Robe Robin Esprite US User Manual

Robe Robin Esprite US User Manual
Version 2.6 US
1
Robin Esprite
Robin Esprite FS
Table of contents
1. Safety instructions.......................................................................................................... 3
2. Operating determination................................................................................................. 4
3. Fixture exterior view ...................................................................................................... 5
4. Installation....................................................................................................................... 6
4.1 Connection to the mains............................................................................................. 6
4.2 Replacing the medium frost ....................................................................................... 6
4.3 Replacing rotating gobos ........................................................................................... 7
4.4 Replacing static gobos ............................................................................................... 9
4.5 Installing the gel frame ............................................................................................... 9
4.6 Rigging the fixture..................................................................................................... 10
4.7 DMX-512 connection................................................................................................. 12
4.8 Ethernet connection.................................................................................................. 13
4.9 Wireless DMX operation........................................................................................... 15
5. Remotely controllable functions.................................................................................. 16
6. Control menu map......................................................................................................... 18
7. Control menu ................................................................................................................ 22
7.1 Tab " Address"........................................................................................................... 23
7.2 Tab "Information"....................................................................................................... 24
7.3 Tab "Personality"....................................................................................................... 26
7.4 Tab "Manual Control"................................................................................................. 28
7.5 Tab "Stand-alone" ..................................................................................................... 28
7.6 Tab "Service"............................................................................................................. 29
8. RDM................................................................................................................................ 33
9. Error and information messages................................................................................. 34
10. Technical Specifications............................................................................................. 37
11. Photometric diagrams................................................................................................. 42
12. Maintenance and cleaning.......................................................................................... 51
12.1 Disposing of the product......................................................................................... 51
13. ChangeLog .................................................................................................................. 52
14. Appendix .....................................................................................................................53
14.1Changing the LED light source................................................................................53
14.2. Obtaining information about the LED light source by mobile phone .....................57
2
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualified
- follow the instructions of this manual
CAUTION!
Be careful with your operations.
With a high voltage you can suffer
a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
Never let the power-cord come into contact with other cables! Handle the power cord and all connections with
the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable
to completely remove power from unit when not in use or before cleaning or servicing the unit.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
The electric connection, repairs and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
For replacement use fuses of same type and rating only.
LED light emission. Risk of eye injury.
Do not look straight at the fixture´s LED source during operation. The intense light
beam may damage your eyes.
3
Do not view the light output with optical instruments or any device that may
concentrate the beam.
CAUTION! Risk group 2, RG-2
Immunity of the equipment is designed for electromagnetic environments E1, E2, E3 according to the standard
EN55103-2 ed.2 Electromagnetic compatibility. Product family standard for audio, video, audiovisual and entertainment lighting control apparatus for professional use. Part 2: Immunity.
The installation company should check levels of possible interferences above the tested levels E1,E2,E3 given
by this standard (e.g. transmitters in surrounding area) before installing the equipment.
Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia
equipment – Emission Requirements according to class B.
2. Operating determination
This device is a moving head for creating decorative effects and was designed for indoor use only.
This device is for professional use only. It is not for household use.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the
fixture at the transport handles.
When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture
or dust. There should not be any cables lying around. You endanger your own and the safety of others!
Make sure that the area below the installation place is blocked when rigging, de-rigging or servicing the fixture.
Always fix the fixture with an appropriate safety rope. Fix the safety rope at the correct holes only.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
The maximum ambient temperature 45°C must never be exceeded.
CAUTION!
The front lens has to be replaced when it is obviously damaged,
so that its function is impaired, e. g. due to cracks or deep scratches!
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the device. Most damages are the result of unprofessional operation!
Do not block the front objective lens with any object when the fixture is under operation.
The fixture housing never must be covered with cloth or other materials.
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, burns etc.
CAUTION!
To avoid damage of the internal parts of the fixture head, never let the sunlight lights
directly to the front lens , even when the fixture is not working !
4
3. Fixture exterior view
1 - Front lens
2 - Camera*
3 - Arm
4- Handles
5 - Head
6 - Tilt lock
7 - Pan lock
8 - Base
*ESPRITE FS only
The head has to be locked for transportation- the tilt lock latch (6) and the pan lock latch (7) have to be in the
locked positions. To unlock the head, move these latches to unlock position before operating the fixture.
Rear panel of the base:
9 - Ethernet input (RJ45)
10 - 3-pin DMX output
11 - 5-pin DMX output
12 - Fuse holder
13 - Camera output (RJ 45)*
14 - 3-pin DMX input
15 - 5-pin DMX input
16 - Power (PowerCon True 1)
*ESPRITE FS only
Front panel of the base:
17 - QVGA touch screen
18 - ESCAPE button
19 - NEXT button
20 - ENTER/DISPLAY ON button
21 - PREV button
22 - USB port
The ENTER/DISPLAY ON button also serves for switching the display on when the fixture is disconnected
from the mains.
5
4. Installation
Fixtures must be installed by a qualified electrician in accordance with all
national and local electrical and construction codes and regulations.
4.1 Connection to the mains
For protection from electric shock, the fixture must be earthed!
The Robin Esprite is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC
power source from 100-240 Volts.
Power cable is enclosed to the fixture. If you need to install a power plug on the power cable to allow connection
to power outlets, install a grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you
have any doubts about proper installation, consult a qualified electrician.
Core (EU)
Core (US)
Connection
Plug Terminal Marking
Brown
Black
Live
L
Light blue
White
Neutral
N
Yellow/Green
Green
Earth
This device falls under class one and must be earthed (grounded).
To apply power, first check that the head pan and tilt locks are released.
4.2 Replacing the medium frost
Unplug the fixture from mains before installing the frost module!
To replace the frost module.
1. Disconnect the fixture from mains and allow it to cool for 10 minutes.
2. Remove plastic cover of the head by loosening the 2 quarter-turn fasteners on the cover to get access to
the frost module (1).
3. The holder (2) of the frost foil is fastened to the frost holder (3) by means of the four magnets (4). Grip the
holder (2) and carefully tilt it out to break a force of magnets (4) on the frost holder (3).
4. Place a new frost module into the frost holder (3). Check, that both slots (6) snapped correctly into two
protrusions (5) in the holder (3).
5. Place the plastic cover back on the fixture before applying power.
6
4.3 Replacing rotating gobos
1. Close a light output of the fixture and allow the fixture to cool about 15 minutes.
2. Put the fixture on the table and remove top plastic covers of the head by loosening the 2 quarter-turn fasteners
on each cover.
3. Connect the fixture to mains. Go to the tab "Service", select the menu "Adjust DMX values " and move
the fixture head to the position which is intended for changing rot. gobos as shown on the picture below.
4. Remove the top plastic cover of the head by loosening the 2 quarter-turn fasteners on the cover.
Place for rot. gobos
changing
5. Escape from the menu "Adjust DMX values " and go to the menu " Rotating Gobos Change" in the same tab,
select Gobo Carousel 1 and enter to its menu.
6. Select a gobo (G1-Mg, G2, G3, G4, G5, G6, G7) which you wish to replace. The selected gobo will move to
the accessible position for its changing.
Note: "G1-Mg" means the gobo holder with a magnet.
7. Check that the position point (4) on the gobo holder aims exactly to the toothlike projection (6) on
the edge of the rotating gobo wheel. If not, go to the option "Gobo Offset" and adjust the position point (4)
exactly opposite of the toothlike projection(6). Adjusted value in the "Gobo Offset" is valid for all gobos on
the gobo carousel.
Note: The magnet (7) on the gobo holder substitutes the position point (4).
7
8. Gently pull up the gobo holder (3) from the rotation gobo carousel.
9. Remove the spring lock (1) with an appropriate tool (e.g. small-bladed screwdriver).
Do not touch the surface of the pattern of the glass gobo with bare fingers.
10. Remove the original gobo (2) and insert the new one (glossy side towards the light source, black matt side
towards the front lens).
The Robe gobo has a small position point (5) at its edge which has to aim at the position point (4) on
the gobo holder (3). Insert the spring lock (1) to secure correct gobo position in the gobo holder (3).
11 Insert the gobo holder back into gobo carousel in this way, that its position point (4) (or magnet (7) has to
exactly aim at a small toothlike projection (6) on the edge of the rotating gobo wheel. Do not move with
neighbouring gobo holders.
12. Escape the gobo item and enter another gobo item which you want to replace. You do not need to set
the gobo offset again. Repeat steps 6, 8-12 for all gobos which you need to replace on the gobo carousel.
Note. The hot-spot lens with holder can be installed instead of the rot. gobo 7.
8
4.4 Replacing static gobos
Disconnect the fixture from mains before replacing gobos!
1. Disconnect the fixture from mains and allow it to cool.
2. Remove the plastic cover of the head by loosening the 2 quarter-turn fasteners on the cover.
3. Gently pull up the gobo holder (1) from the static gobo wheel.
4. Remove the spring gobo-lock (3) with an appropriate tool (e.g. small-bladed screwdriver) and remove it.
Do not touch the surface of the pattern of the glass gobo.
5. Remove the original gobo (2) and insert the new one (glazy side towards the light source). Insert the
spring-gobo lock (3) to secure it in the gobo holder (1).
6. Insert the gobo holder back to the static gobo wheel until it reaches the stop (4) in the static gobo wheel.
5. Replace the bottom cover before applying power.
4.5 Installing the gel frame
Disconnect the fixture from mains before installing the gel frame adaptor.
1. Screw the gel frame adaptor [P/N 10980463] (1) on the head (2) by means of the six screws M4x10 (3).
2. Insert the gel frame [P/N 10980464] (4) to the gel frame adaptor and secure it by the spring lock (5).
Max. dimension of transparent film (for inserting to the gel frame) is 210 x 210 mm.
9
4.6 Rigging the fixture
A structure intended for installation of the fixture(s) must safely hold weight of the fixture(s) placed on it. The
structure has to be certificated to the purpose.
The fixture (fixtures) must be installed in accordance with national and local electrical and construction codes
and regulations.
For overhead installation, the fixture must be always secured with a safety wire
that can bear at least 10 times the weight of the fixture
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.
The operator has to make sure that safety relating and machine technical installations are approved by a skilled
person once a year.
Allow the fixture to cool for ten minutes before handling.
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working
load limits, installation material being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualifications, do not attempt the installation yourself, but use a help of professional
companies.
CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do not install the fixture!
The fixture has to be installed out of the reach of public.
The fixture must never be fixed swinging freely in the room.
Danger of fire !
When installing the device, make sure there is no highly inflammable
material (decoration articles, etc.) in a distance of min. 1 m.
CAUTION!
Use 2 appropriate clamps to rig the fixture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is fixed properly! Ensure that the
structure (truss) to which you are attaching the fixtures is secure.
The fixture can be placed directly on the stage floor or rigged in any orientation on a truss without altering its
operation characte­ristics .
For securing the fixture to the truss, install a safety wire which can hold at least 10 times the weight of the fixture.
Use only the safety wire with a snap hook with screw lock gate.
10
Truss installation
1.Bolt clamps (4) to the brackets Omega CL (1) with M12 bolts and lock nuts through the hole in the bracket
Omega CL.
2.Fasten the brackets Omega CL on the bottom of the base by means of the quick-lock fasteners (2) and tighten
them fully clockwise.
3. Lock the snap hook of the safety wire (3) in the attachment point (5) a) and pull the safety wire around
the truss (6) in a suitable position so that the maximum fall of the fixture will be 20 cm. Lock the snap hook
with screw lock gate.
1-Mounting bracket Omega CL
2-Quick-lock fasteners
3-Safety wire
4-Clamps
5-Attachment point
6-Truss
When installing fixtures side-by-side,
avoid illuminating one fixture with another!
DANGER TO LIFE!
Before taking into operation for the first time,the installation has to be approved by
an expert!
11
4.7 DMX-512 connection
The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output. The sockets are wired
in parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in
order to connect the controller with the fixture or one fixture with another.
DMX outputDMX input
XLR mounting sockets (rear view):
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
XLR mounting plugs (rear view):
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with
the DMX input of the first fixture in the DMX chain. If you wish to connect DMX controllers with other XLR outputs, you need to use adapter cables.
Building a serial DMX chain:
Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture. Always connect
one output with the input of the next fixture until all fixtures are connected. Up to 32 fixtures can be conected.
Caution: At the last fixture, the DMX cable has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a 3-pin XLR plug and plug it in the DMX output of the last fixture.
12
4.8 Ethernet connection
The fixtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control software running on your PC (or light console) has to support Art-Net protocol.
Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow
transfer of large amounts of DMX 512 data over a wide area using standard network technology.
IP address is the Internet protocol address.The IP uniquely identifies any node (fixture) on a network.
The Universe is a single DMX 512 frame of 512 channels.
The Robin Esprite is equipped with 8-pin RJ- 45 socket for Ethernet input.Use a network cable category 5 (with
four “twisted” wire pairs) and standard RJ-45 plugs in order to connect the fixture to the network.
RJ-45 socket (front view):
RJ-45 plug (front view):
1- TD+ 5- Not connected
2- TD-6- RX3- RX+7- Not connected
4- Not connected
8- Not connected
Patch cables that connect fixtures to the hubs or LAN sockets are wired 1:1,that is,pins with the same numbers
are connected together:
1-1
2-2
3-3
4-4
5-5
6-6
7-7
8-8
If only the fixture and the computer are to be interconnected,no hubs or other active components are needed.A
cross-cable has to be used:
1-3
2-6
3-1
4-8
5-7
6-2
7-5
8-4
If the fixture is connected with active Ethernet socket (e.g. switch) the network icon
will appear at the
bottom right corner of the screen:
Direct Ethernet operation
Connect the Ethernet inputs of all fixtures with the Ethernet network.
Option “ Artnet" (gMaI or gMA2 or sACN) has to be selected from “Ethernet Mode” menu at each fixture.
Set IP address (002.xxx.xxx.xxx / 010.xxx.xxx.xxx) and the Universe at each fixture.
(DMX address=146)
IP addres=002.168.002.004
Universe=1
(DMX address=50)
IP addres=002.168.002.003
Universe=1
(DMX address=1)
IP addres=002.168.002.002
Universe=1
An advised PC setting: IP address: 002.xxx.xxx.xxx / 010.xxx.xxx.xxx (Different from fixture IP addresses)
NET mask: 255.0.0.0
13
Ethernet / DMX operation
Option “ Artnet" (gMaI or gMA2 or sACN) has to be selected from “Ethernet Mode” menu at first fixture.
Option “Ethernet To DMX” has to be selected from the “Ethernet Mode” menu at the first fixture (connected to
the Ethernet) in the fixture chain, next fixtures have standard DMX setting.
Connect the Ethernet input of the first fixture in the data chain with the network. Connect the DMX output of this
fixture with the input of the next fixture until all fixtures are connected to the DMX chain.
Caution: At the last fixture, the DMX chain has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a XLR-plug and connect it in the DMX-output of the last fixture.
Example:
DMX address=1
IP addres=002.168.002.002
Universe=0
DMX address=50
DMX address=1
DMX address=50
IP addres=002.168.002.003
Universe=1
14
DMX address=146
DMX address=146
4.9 Wireless DMX operation
The wireless version of the Robin Esprite is equipped with the Lumen Radio CRMX module and antenna for
receiving DMX signal. CRMX module operates on the 2.4 GHz band.
The item " Wireless " from the menu "DMX Input" allows you to activate receiving of wireless DMX (Personality--> DMX Input -->Wireless.). First two options from the "DMX Input" menu are stated in DMX chart as well
(channel Power/Special functions , range of 10-19 DMX). If DMX input option is changed by DMX command,
the change is permanently written into fixture´s memory.
DMX range of 10-19 switching fixture to the wired/wireless operation is active only during first 10 seconds after switching the fixture on.
After switching the fixture on, the fixture checks both modes of receiving DMX in the following order:
1. For the first five seconds, the fixture receives DMX signal from the wired input. If the Power/Special functions
channel is set at some DMX input option, the fixture will receive DMX value according to this option. If DMX input
option is set to the wired input , this option is saved and checking procedure is finished. If DMX input option is
not set, the fixture continues next 5 seconds in scanning wireless DMX signal-see point 2.
2. For the next 5 seconds the fixture receives wireless DMX signal and again detects if the Power/Special
functions channel is set at some DMX input option, if not, the fixture will take option which is set in the fixture
menu "DMX Input".
To link the fixture with DMX transmitter.
The fixture can be only linked with the transmitter by running the link procedure at DMX transmitter .
After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item “Wireless State“ (Information
-->Wireless State).
To unlink the fixture from DMX transmitter.
The fixture can be unlinked from receiver via the menu item “ Unlink Wireless Adapter“ (Information--> Wireless
State --> Unlink Wireless Adaptor).
Note: If the option "Wireless In/XLR Out" is selected (Personality--> DMX Input -->Wireless In/XLR Out), the
fixture receives wireless DMX and sends the signal to its wired DMX output. The fixture behaves as " Wireless/
Wired" adaptor.
Example
of connection:
15
5. Remotely controllable functions
Effect wheel
The wheel rotates in both directions with variable speed which creates wide spectrum of graphic effects.
Gobo wheels
The fixture includes static gobo wheel with 9 gobos and rotating gobo wheel with 7 glass gobos rotating in
both directions, indexable, replaceable "SLOT&LOCK” system. The hot-spot lens can be installed instead of
the rot. gobo 7.
Prism
The 6-facet prism rotates in both directions at different speeds, 16 prism/gobo macros are available.
Frost
Two frost filters (light 1°and medium 5°) provide variable frost for fine frosting. The medium frost is replaceable.
Iris
Motorized adjustable iris, wide range of variable pulse effects.
Zoom
Motorized zoom unit enables zoom between 5.5 °- 49°.
Focus
Motorized focus allows to focus beam from approx. 2 meters to infinity.
Framing system
Framing system consists of four framing shutters. There is individual control of each shutter blade position
and angle, together with rotation of the complete framing module. As well as providing a sharp precise or soft
frame for the projected image.
Framing system orientation:
16
Pan/Tilt
Fast pan/tilt movement due to built-in electronic motion stabilizer (EMS). The electronic motion stabilizer ensures
precise position of the fixture´s head during its movement and reduces its swinging when the truss shakes.
Pan /Tilt movement range: 0-540°/0-280°.
Colour wheel 1
This wheel contains five dichroic filters + open. The colour wheel can be positioned between two adjacent
colours in any position. It is also possible to rotate the colour wheel continuously at different speeds ("Rainbow
effect“ in both directions).
Colour wheel 2
This wheel contains one multicolour filter, two dichroic filters and two CRI filters (80, 90) + open. The colour
wheel can be positioned between two adjacent colours in any position. It is also possible to rotate the colour
wheel continuously at different speeds ("Rainbow effect“ in both directions).
CMY+CTO colour mixing system
The CMY color mixing system is based on graduated cyan, magenta, and yellow colour filters. A continuous
range of colors may be achieved by varying the amount of each filter from 0 to 100%.
17
6. Control menu map
Default settings=Bold print
Tab
Level 1
Level 2
Level 3
Addressing
Settings
DMX Address
001-512
DMX Presets
Mode 1
Level 4
Mode 2
View Selected Preset
Ethernet Settings
Ethernet Mode
Disable
ArtNet
gMAI
gMA2
sACN
Ethernet To DMX
Off, On
IP Address/Net Mask
Default IP Address
Custom IP Address
Net Mask
Information
Fixture Times
ArtNet Universe
0-255
MANet settings
MANetI/II Universe
01-256
MANet Session ID
01-32
sACN Settings
sACN Universe
00001-32000
Power On Time
Total Hours
Resetable Hours
LEDs On Time
Total Hours
Resetable Hours
Air Filters
Elapsed Time
Alert Period
Fixture Temperatures
LEDs Temperatures
Cur.rent
Maximum NonRes..
Maximum Res..
Driver Temperature
Cur.rent
Maximum NonRes..
Maximum Res..
Base Temperature
Current
Maximum NonRes.
Maximum Res.
DMX Values
Pan
:
Dimmer Fine
Wireless State
Signal Quality
Unlink
Wireless Adapter
Power Channel state
Software Versions
Display System
Module M
Module L
Module O
Module F-A
Module F-B
Module G
Module FR
Module C1
Module C2
Product IDs
Mac Address
RDM UID
18
10-300
Level 5
Level 6
Tab
Level 1
Level 2
Level 3
Level 4
RDM Label
LED Module info
First Module Assembly
Actual Module Info
Assembly History
Intensity History
LED Modules History
View Logs
Fixture Errors
Fixture States
Power On
Power Off
Fixture Position
Fixture Temperatures
LEDs Temperature
Driver Temperatures
Base Temperatures
Personality
User Mode
User A Settings
User B Settings
DMX Presets
Mode 1
Mode 2
View Selected Preset
DMX Input
Wired
Wireless
Wireless In/XLR Out
Pan/Tilt Settings
Pan Reverse
Off, On
Tilt Reverse
Off, On
Pan/Tilt Feedback
Off, On
Pan/Tilt mode
Time
Speed
Pan/Tilt EMS
Off
Soft
Medium
Hard
Microphone Sensitivity
1-10-20
Blackout Settings
Blackout During M.C.
Off, On
Blackout while:
Pan/Tilt moving
Off, On
Colour Wheel Moving
Off, On
Frequency Setup
300 Hz
600Hz
1200Hz
2400Hz
Frequency Adjust
Init Effect Positions
Pan
0-255
:
Screen Settings
Dimmer Fine
0-255
Display Intensity
1-10
Screen Saver Delay
Off-10min.
Touchscreen Lock
Off-10min.
Recalibrate Touchscreen
Display Orientation
Normal
Inverted
Auto
Temperature Unit
°C,°F
Fan Mode
Auto
High
Quiet
High-power mode
Off, On
19
Level 5
Level 6
Tab
Level 1
Level 2
High-power Mode
Off, On
Dimmer Curve
Linear
Level 3
Level 4
Level 5
Level 6
0-255
Square law
Date & Time Settings
Default Settings
Password Protection
Off, On
Reset Web Password
Manual Control
Reset Functions
Total System Reset
Pan/Tilt reset
Color System Reset
Gobo/Eff. Wh. Reset
Optics/Prism/Frost Res.
Iris/framing Sh. Reset
Manual Effect Control
Pan
0-255
:
Dimmer Fine
Stand -Alone
Test Sequences
0-255
Dynamic Mode
Static Mode
Pan
0-255
Tilt
0-255
Zoom
0-255
Focus
0-255
Edit Program 1
Start Step
1-80
Edit Program 2
End Step
1-80
Edit Program Steps
Step 1
Pan
:
:
:
Dimmer Fine
0-255
:
Step Time
0-25,5 sec.
Step 80
Pan
0-255
MusicTrigger
Off, On
Preset Playback
None
Test
Prog. 1
Prog. 2
Play Program
Play Program 1
Play Program 2
Edit Program
:
Service
Adjust DMX Values
Pan
0-255
:
Calibrations
Dimmer Fine
0-255
Calibrate Effects
Pan
0-255
Tilt
0-255
Effect Wheel
0-255
Rot. Gobo Wheel
0-255
R. Gobo Index 1
0-255
:
:
R. Gobo Index 7
0-255
Static Gobo
0-255
Colour Wheel 1
0-255
Colour Wheel 2
0-255
Prism 1
0-255
Prism 2
0-255
Zoom
0-255
20
Dimmer Fine
0-255
Step Time
0-25,5 sec.
Tab
Level 1
Level 2
Calibrate Fr. Hysteresis
Level 3
Level 4
Focus
0-255
Iris
0-255
Frost 1/1
0-255
Frost 1/2
0-255
Frost 2/1
0-255
Frost 2/2
0-255
Fr. Shutters rot.
0-255
Fr. Shutter 1 Move
0-255
Fr. Shutter 1 Swiv
0-255
Fr. Shutter 2 Move
0-255
Fr. Shutter 2 Swiv
0-255
Fr. Shutter 3 Move
0-255
Fr. Shutter 3 Swiv
0-255
Fr. Shutter 4 Move
0-255
Fr. Shutter 4 Swiv
0-255
Framing Lamella 1
0-8
Framing Lamella 2
0-8
Framing Lamella 3
0-8
Framing Lamella 4
0-8
Calibrate Pan/Tilt EMS
Load Default Calibrations
Rotating Gobos
Change
Gobo Carousel 1
G1-Mg
G2
:
G7
Gobo Offset
LEDs Measure
Update Software
21
0-255
Level 5
Level 6
7. Control menu
The Robin Esprite is equipped with the QVGA Robe touch screen with battery backup which
allows you to set the fixture´s behaviour according to your needs, obtain information on its operation, control
all range of effects and program it in stand-alone mode.
The fixture´s menu can be controlled either by the control buttons or directly by touching the icon.
Control buttons on the front panel:
[ESCAPE] button used to leave the menu without saving changes.
[NEXT] , [PREV] buttons for moving between menu items and symbols, adjusting values.
[ENTER/Display On] button used to enter the selected menu (menu item) and to confirm adjusted value.
If the fixture is disconnected from mains, the button switches the touch screen on.
Icons used in the touch screen menu:
- [back arrow] used to move back to the previous screen (menu).
- [up arrow] used to move up on the previous page.
- [down arrow] used to move down on the next page.
- [confirm] used to save adjusted values, to leave menu or to perform desired action.
- [cancel] used to leave menu item without saving changes.
- [confirm+copy] used to save adjusted values and copy them to the next prog. step.
- [warning icon] used to indicate some error which has occurred in the fixture.
- [Ethernet] used to indicate Ethernet connected.
- [menu rotation] used to rotate menu 180 degrees from current orientation.
- [slider control] used to recall slider system for setting desired value.
- [keyboard control] used to recall keyboard system for setting desired value.
- [air filters cleaning] used to signal that cleaning period of the air filters elapsed.
The menu page displays icons for each function that you can perform from the touch screen.
After switching the fixture on, the touch screen shows the screen with the ROBE logo:
22
Touch any part of the screen or press the [ENTER/Display On] button to display the initial screen with the current stored DMX address:
Note: The green icon at the top right corner of the screen indicates the level of the display battery charging. If
the whole icon is green, the battery is fully charged while the red icon indicates exhausted battery. The battery
charges during fixture operation, its charging lasts cca 6 hours.
We recommend that the fixture should be in operation at least 7 hours per week to keep the battery fully charged.
If you switch the fixture on and this screen will not appear till 1 minute, switch the fixture off and on again. If the
screen lights, the battery is exhausted. In case the screen still does not light, the battery is faulty.
This is also indicated by an error message "Faulty battery" and if such an error message appears the battery
should be replaced immediately. The lifetime of the battery is highly dependent on ambient temperature (and
consequently on base temperature). If the maximum ambient temperatures (as recorded and displayed in menu:
Information -> Fixture Temperatures -> Ambient Temperature -> Maximum NonRes.) are kept within the specified limits, the battery should last for at least two years. Shell the ambient temperatures exceed the specified
maximum temperature, the lifetime of the batteries could be considerably shortened even up to just one year
or less and also result in physical damage (battery leakage) or unreliable fixture functions.
Damage caused by batteries failed due to exceeded maximum ambient temperature cannot be claimed under
warranty terms.
Touch the green arrow at the bottom right corner of the screen or press the [ENTER/Display On] button to enter
the " Address" menu.
Each item (such as a Tab, menu item, text box, icon) may be selected from a screen by simply touching the
item in the list or by pressing the [NEXT] or [PREV] buttons to scroll through list items. With each press, the
next item is highlighted. Press [ENTER/Display On] to select the highlighted item.
Before first fixture operation, set current date and time in the menu "Date &Time
Setings" (menu path: Personality--> Date &Time Setings).
7.1 Tab " Address"
DMX Address - Select the menu to set the DMX start address.
DMX Preset - Use the menu to select desired channel mode.
DMX Preset - Use the menu to select desired channel mode.
Mode 1 - 49 control channels
Mode 2 - 42 control channels
View Selected Preset - Use the menu to display channels included in the selected mode.
Ethernet Settings - The menu allows all needed settings for the Ethernet operation
Ethernet Mode
Disable - The option disables Ethernet operation.
Artnet - Fixture receives Artnet protocol
gMAI - Fixture receives MANet I protocol
gMA2 - Fixture receives MANet 2 protocol
sACN - Fixture receives sACN protocol
23
Ethernet To DMX - Fixture receives protocol from the Ethernet input and sends DMX
data to its DMX output (fixture works as an "Ethernet/DMX converter", next fixture can
be connected to its DMX output and you can build a standard DMX chain by connecting another fixtures.
Only one fixture has to be connected to the Ethernet.
IP Address/Net Mask - Select this menu to set IP address. IP address is the Internet protocol
address. The IP uniquely identifies any node (fixture) on a network.
There cannot be 2 fixtures with the same IP address on the network!
Default IP Address -Preset IP address, you can set up only first byte of IP address
(2 or 10) e.g. 002.019.052.086.
Custom IP Address - The option enables to set up all bytes of IP address.
Net Mask - The option enables to set up all bytes of Net Mask.
ArtNet Universe - Use this item to set a Universe (0-255). The Universe is a single DMX
512 frame of 512 channels.
MANet Settings - Use this menu to set parameters for MANet operation.
MANet Universe I/II - The value of this item can be set in range 1-256.
MANet Session ID - The value of this item can be set in range 1-32.
sACN Settings - Use this menu to set parameters for sACN operation.
sACN Universe - The value of this item can be set in range 1-32000.
7.2 Tab "Information"
Fixture Times - The menu provides readouts of fixture and LED module operation hours.
Power On Time Hours - Select this menu to read the number of fixture operation hours.
Total Hours - The item shows the total number of the operation hours since the Robin Esprite has been fabricated.
Resetable Hours - The item shows the number of the operation hours that the Robin Esprite has been powered on since the counter was last reset.
In order to reset this counter to 0, touch the text box next to the item "Resetable Hours:"
LED On Time - Select this menu to read the number of LEDs operation hours.
Total Hours - a total time of the LEDs module operation during which a dimmer intensity
was > 0%.
Adaptive Hours - a relative time of the LEDs module operation during which a dimmer intensity
was > 0%.(e.g. if dimmer = 20% for one hour, the adaptive time is 0.2 hour, if dimmer = 100%
for one hour, the adaptive time is 1 hour).
Air Filters - Regular cleaning of the air filters is very important for the fixture´s life and performance.
Bild-up of dust, dirt and fog fluid residues reduces the fixture´s light output and cooling ability.
The two items of this menu help you to keep cleaning period of the air filters.
Alert period - Cleaning schedule for the fixture depends on the operating environment.
It is therefore impossible to specify accurate cleaning interval. This item allows
you to change the cleaning interval of the air filters. This "alert" value is 300 hours and it
is set as default. Inspect the fixture within its 300 hours of operation to see whether cleaning
is necessary. If cleaning is required, clean all air filters and change the value in this menu
on acceptable level. Min. level of alert period is 10 hours, max. is 300 hours.
Elapsed Time - The item allows you to read the time which remains to cleaning air filters.
The time period is set in the menu mentioned above.
Expired time period is signalled by a negative mark (-) at the time value and a warning icon
on the display.
Clean the filters and reset this menu item (by touching the text box next to the item
"Elapsed Time").
Fixture Temperatures - The menu is used to view temperatures of the fixture´s inside.
LEDs temperature - The menu shows temperature on the LED PCB in the light source
24
Current - A current temperature of the LED PCB.
Maximum NonRes. - A maximum temperature of the LED PCB since the fixture has been
fabricated.
Maximum Res. - A maximum temperature of the LED PCBs since the counter
was last reset.
In order to reset some counter to 0, touch desired text box under item "Max.Res."
Driver Temperature - The menu shows temperature on the LEDs control PCB in the fixture head.
Current - A current temperature on the LEDs control PCB.
Maximum NonRes. - A maximum temperature on the LEDs control PCB since
the fixture has been fabricated.
Maximum Res. - A maximum temperature on the LEDs control PCB since the counter
was last reset.
In order to reset this counter to 0, touch the text box next to the item "Maximum Res.
Base Temperature - The menu shows temperature on the display PCB in the fixture base.
Current - A current temperature on the display PCB.
Maximum NonRes. - A maximum temperature on the display PCB since the fixture has
been fabricated.
Maximum Res. - A maximum temperature on the display PCB since the counter
was last reset.
In order to reset this counter to 0, touch the text box next to the item "Maximum Res."
DMX Values - The menu items allows you to read DMX values of each channel received by the fixture.
Wireless State - The menu serves for reading of the wireless operation status.
Unlink Wireless Adapter - The item serves for unlinking the fixture from a DMX transmitter.
If the wireless module is not installed in the fixture, message" Wireless Module Not Installed" will appear.
Power Channel State - Select this item to see current setting of the functions, which can be set by menu items
in "Personality" as well as by DMX command at channel "Power/Special functions".
Colour Functions State - Select this item to see current setting of the colour functions, which can be set by
menu items in "Personality" as well as by DMX command at channel "Colour functions".
Software Version - Select this item to read the software version of the fixture processors:
Display System - A display processor on the display board in the fixture base
Module M - a Pan/Tilt processor
Module L - a LEDs control processor
Module O - a Focus/Zoom/Prism/ control processor
Module F-A -a Framming shutters control processor
Module F-B - a Framming shutters + Iris control processor
Module G - a Rot. gobo/Static gobo wheel control processor
Module FR - a Frost control processor
Module C1 - a Colour wheel 1 control processor
Module C2 - a Colour wheel 2 control processor
Product IDs - The menu is used to read the MAC Address ,RDM UID and RDM Label.
LED Module Info - Use this menu to read LEDs module information.
First Module Assembly - Use the item to read initial information about the LEDs module installed in
the fixture. The fixture has to be connected to mains to read the values in the menu items.
Serial Number/ Device UID - a serial number of the LEDs module/RDM UID of the fixture.
Installation Date/Time - a date/time of the first installation of the LEDs module to a
some Esprite device.
Intensity - an original intensity of the LEDs module in percentages (100%).
LEDs On Time Total/Adaptive - Total: a total time of the LEDs module operation during which
the dimmer intensity was > 0%.
Adaptive: a relative time of the LEDs module operation during which the dimmer intensity
was > 0% (e.g. if dimmer = 50% for one hour, the adaptive time is 0.5 hour, if dimmer = 100%
for one hour, the adaptive time is 1 hour).
25
Actual Module Info - Use the item to read current information about the LEDs module installed in
the fixture.
Serial Number/ Device UID - a serial number of the LEDs module/RDM UID of the fixture.
Measurement Date/Time - a date/time of running the procedure "LEDs Measure" in the tab
Service.
Intensity - the item shows a light intensity of the LEDs module measured after running
the procedure "LEDs Measure" in the tab Service. The light intensity is displayed in percentages
in relation to the initial intensity of the new LEDs module (initial intensity=100%).
LEDs On Time Total/Adaptive - Total: a total time of the LEDs module operation during which
the dimmer intensity was > 0%.
Adaptive: a relative time of the LEDs module operation during which the dimmer intensity
was > 0% (e.g. if dimmer = 50% for one hour, the adaptive time is 0.5 hour, if dimmer = 100%
for one hour, the adaptive time is 1 hour).
Assembly History - Use the item to read a history of the LEDs module installed in the fixture (its serial
number, RDM UID of fixture at which was installed and date/time of installation).
Up to 31 records can be saved in the menu item.
Intensity History - Use the item to read a history of light intensity of the LEDs module installed in the fixture.
Serial Number/ Device UID - a serial number of the LEDs module/RDM UID of the fixture.
Measurement Date/Time - a date/time of running the procedure "LEDs Measure" in the tab
Service.
Intensity - the item shows a light intensity of the LEDs module measured after running
the procedure "LEDs Measure" in the tab Service. The light intensity is displayed in percentages
in relation to the initial intensity of the new LEDs module (initial intensity=100%) .
Up to 31 records can be saved in the menu item.
LED Modules History - Use the item to read a history of the LEDs modules installed in the fixture (their serial
numbers and date/time of installation).
Up to 31 records can be saved in the menu item.
View Logs - Use this menu to read fixture´s data which have been recorded during fixture operation. This
collected data allows easier troubleshooting.
Fixture Errors - Use this menu to read fixture errors which have occurred during fixture operation.
Fixture States - In the menu are recorded fixture states as power on and power off.
Fixture Positions - In the menu are recorded installation positions of the fixture:
Fixture Temperatures - In the menu are recorded temperatures which have exceeded defined levels.
Note: The log buffer can contain max. 8000 records. If the buffer is full, old data will be overwritten.
7.3 Tab "Personality"
User mode - The Robin Esprite allows you to recall two user settings. After switching the fixture on for the first
time, the User A settings is active. Now all changes made in the “Personality” menu , ”Addressing” menu and the
“Music Trigger“ and “ Preset Playback“ items from the “Stand-alone” menu are saved to the User A settings. If
you now select the User B settings, from this moment the changes made in these menus will be saved to the
User B settings. After switching the fixture off and on, the User B setting is active. In this way you may use the
two fixture operating behaviours.
User A Settings - the function recalls the user A settings.
User B Settings - the function recalls the user B settings.
26
DMX Preset - Use the menu to select desired channel mode.
Mode 1 - 49 control channels
Mode 2 - 42 control channels
View Selected Preset - Use the menu to display channels included in the selected mode.
DMX Input- Use the menu to select mode of DMX signal receiving.
Wired - DMX signal is received by means of the standard DMX cable.
Wireless - DMX signal is received by means of the inbuilt wireless module.
Wireless In/XLR Out- the fixture receives wireless DMX and sends the signal to its wired DMX output.
The fixture behaves as " Wireless/Wired" adapter.
The options "Wired" and "Wireless" are also stated in DMX chart (channel Power/Special functions).
Note. If the wireless module is not installed in the fixture, the following message will appear:
DMX Input Set to Wired
Wireless Module Missing
If the fixture is not connected to mains, the message "Not Available In Offline Mode" will appear after entering
the menu DMX Input. To enter this menu, the fixture has to be connected to mains.
Pan/Tilt Settings - Use the menu set behaviour of both pan and tilt movements.
Pan Reverse - The item allows to invert pan movement.
Tilt Reverse - The item allows to invert tilt movement.
Pan/Tilt Feedback - The item allows to return the mowing head to the required pan/tilt position after
changing the position by an external force if this option is set on.
Note. Be careful, the Pan/Tilt Feedback should be permanent On, the option Off is not suitable for standard
operation and the head of the fixture can be damaged!
Pan/Tilt mode - Use this menu to set the mode of the pan/tilt movement
Time mode – The pan and tilt will move with different speeds and they will come at
the same time to the end point of their tracks (pan and tilt use their optimal speeds).
Time of the pan/tilt movement (25.5 sec. max.) is set by the channel "Pan/Tilt speed, Pan/Tilt
time".
Speed Mode - Both Pan and tilt will move with the same speed as adjusted at the channel
"Pan/Tilt speed, Pan/Tilt time".
Pan/Tilt EMS - Built-in electronic motion stabilizer ensures precise position of the fixture´s head during its
movement and also reducing its swinging when the truss shakes.
Follow Spot Mode - If the function is activated, the pan/tilt motors perform on lower power and the head position
can be controlled manually. You can choose from three levels of the pan/tilt "consistency": soft, medium and hard.
Note: reset of pan/tilt will not be executed if the fixture is in the Follow Spot Mode.
Microphone Sensitivity - Enter the menu if you want to adjust the microphone sensitivity from 1 (max.) to 20
(min.).
Blackout Settings - Use the menu if you need to close the light output under certain conditions which are
described below
Blackout During MC - Blackout during movement correction. Set this option On if you wish to close light
output during the time when the head goes to its correct position from which has been changed by an
external force.
Active Blackouts - Use this menu if you wish to close the light output during effect changes.
Pan/Tilt Moving - The menu item enables to close light output while the pan/tilt DMX values
are changing.
Colour Wheel Moving - The menu item enables to close light output while colour wheel
is moving.
Frequency Setup - The function allows you to set the PWM (Pulse Width Modulation) output frequency of
LEDs to 300Hz, 600Hz, 1200Hz or 2400Hz.
Frequency Adjust - The menu item allows you fine adjustment of the LED frequency around selected frequency.
Init Effect Positions - Use the menu to set all effects to the desired positions at which they will stay after
switching the fixture on without DMX signal received.
Screen Settings - Use this menu to change the touch screen settings.
Display Intensity - The item allows to control the intensity of the screen (1-min., 10-max.).
Screen saver Delay - The item allows you to keep the screen on or to turn it off automatically after 1-10
minutes after last touch (or pressing any button on the control panel).
27
Touchscreen Lock - The item allows you to lock the screen after last touch (or pressing any button on the
control panel). The time delay can be set in range of 1-10 minutes.To unlock the screen, press the
[ENTER/Display On] button.
Recalibrate Touchscreen - The item starts calibration of the touch screen. Follow the instructions on
the screen.
Display Orientation - The menu allows to change display orientation.
Normal - Standard display orientation if the fixture is placed horizontally (e.g. on the ground).
Inverted - Inverted orientation (needed if the fixture is hanging on the truss).
Auto - The option activates a gravitation sensor for automatic screen orientation.
Note: Auto option is set as default. You change the display orientation by touching the icon
on the display,
an the option set in the "Display Orientation" menu is temporarily overriden.
Temperature unit - Use the menu item to change temperature unit from °C to °F.
Fan Mode - Use the menu to set the fixture fans to max. power mode ("High") or to the auto-control mode
("Auto"). The option "Quiet" allows you to set desired fan noise. The light output of the fixture
is reduced at low speeds of fans and the High-power Mode is deactivated.
High-power Mode - If the High-power Mode is On, the light output from the fixture will be increased about 6%
towards to the operation with fans in High mode. Fans will run on max. power.
Dimmer Curve - Use the menu to select desired dimmer curve: Linear or Square Law.
Date & Time Settings - Use this menu to set current date and time for the fixture log system (menu "View
Logs"). Set this menu items before first fixture operation.
Default Settings - The menu item allows to set all fixture parameters in this menu to the default (factory) values
except items "DMX Input".
Password Protection - allows to enter password in order to prevent unauthorized person from changing setting
of the fixture.
Reset Web Password - The menu item allows you to reset a password for access on the Web server (default
password: 2479, user: robe).
7.4 Tab "Manual Control"
Reset Functions - The menu allows to reset the fixture either per function modules or all modules together.
Total System Reset - The item resets all function modules.
Pan/Tilt Reset - The item resets a pan and a tilt.
Colour System Reset - The item resets colour wheel 1/colour wheel 2 and CMY+CTO system.
Gobo/Eff. Wh. Reset - The item resets static and rotating gobo wheel and an effect wheel.
Optics/Prism/Frost Res. - The item resets a zoom, focus, prism and a frost module.
Iris/Framing Sh. Reset - The item resets an iris module and framing shutters.
Manual Effect control - Use the menu to control all fixture channels by means of the control panel.
7.5 Tab "Stand-alone"
Test Sequences -Use the menu to run a test/demo sequences without an external controller, which will show
you some possibilities of using Robin Esprite.
28
Dynamic Mode - This mode uses all Robin Esprite functions including pan/tilt movement and therefore
is good for a complete introduction of the fixture.
Static Mode - This mode is suitable for projections on the wall, ceiling or ground without any pan/tilt movement.
Adjust the pan, tilt, zoom and focus to desired positions an start test sequences by touching the green icon.
Music Trigger - Use the item to activate the sound control of the running program via the built-in microphone.
Preset Playback - This menu allows you to select the program which will be played in a loop after switching
the fixture on (the option is commonly used in a stand-alone operation without an external controller).
None - The option disables “Presetting playback” function.
Test - The option starts the test sequences.
Prog. 1 - The option starts user program No. 1.
Prog. 2 - The option starts user program No. 2.
Play program - Use the menu to run desired program in a loop.
Play Program 1 - The option starts user program No.1.
Play Program 2 - The option starts user program No. 2.
Edit Program - Use the menu to create or to edit desired program. The Robin Esprite offers 2 free programs,
each up to 80 steps.
Edit Program 1 - The option allows to edit user program No.1.
Edit Program 2 - The option allows to edit user program No.2.
To edit program:
1. Touch the item which you want to edit (“Edit Program 1” - “Edit Program 2”).
2. Touch the item "Edit Program Steps".
3. Touch the item "Step 1".
4 From the list of effects touch desired effect and set its value. Browse throw the list by touching the [up arrow]
and [down arrow] and set all desired effects.
An item "Step Time" (value of 0-25.5 sec.) is the time during which effects last in the current step
5. Save adjusted effects to the current step by touching the [confirm] or save and copy them to the following
step by touching the [confirm+copy]. By touching the text box "Preview" next to the current program step you
can view created scene.
6. Repeat the steps 4 and 5 for next program steps.
7. After editing desired program steps, adjust the length of the program by touching the text boxes "Start Step"
and "End Step".
Meaning of the icons used in the "Edit Program" menu:
- moves down on the next page
- saves adjusted values and leaves menu
- moves up on the previous page
- saves values to the current step and copy them to the
following prog. step
- leaves menu without saving values
7.6 Tab "Service"
Adjust DMX Values - The menu allows you to set all effects to desired positions before fine calibration of the
effects .
Calibrations - This menu enables fine calibration of fixture effects and download default calibration values.
Calibrate Effects - The menu allows the fine adjustment of effects.
Pan- a pan position fine adjustment (value range: 0-255)
Tilt - a tilt position fine adjustment (value range: 0-255)
Effect Wheel - an effect wheel position fine adjustment (value range: 0-255)
Rot. Gobo Wheel - a carousel of rotating gobos fine movement (value range: 0-255)
R. Gobo Index 1 - a fine movement of the rotating gobo 1 (value range: 0-255)
R. Gobo Index 2 - a fine movement of the rotating gobo 2 (value range: 0-255)
R. Gobo Index 3 - a fine movement of the rotating gobo 3 (value range: 0-255)
R. Gobo Index 4 - a fine movement of the rotating gobo 4 (value range: 0-255)
R. Gobo Index 5 - a fine movement of the rotating gobo 5 (value range: 0-255)
R. Gobo Index 6 - a fine movement of the rotating gobo 6 (value range: 0-255)
R. Gobo Index 7 - a fine movement of the rotating gobo 7 (value range: 0-255)
29
Static Gobo - a static gobo wheel fine movement (value range: 0-255)
Colour Wheel 1 - a colour wheel 1 fine movement (value range: 0-255)
Colour Wheel 2 - a colour wheel 2 fine movement (value range: 0-255)
Prism 1 - a prism fine movement (value range: 0-255)
Prism 2 - a prism fine rotation (value range: 0-255)
Zoom - a zoom module fine movement (value range: 0-255)
Focus - a focus module fine movement (value range: 0-255)
Iris - an iris fine movement (value range: 0-255)
Frost 1/1 - a light frost fine position movement 1
Frost 1/2 - a light frost fine position movement 2
Frost 2/1 - a medium frost fine position movement 1
Frost 2/2 - a medium frost fine position movement 2
Fr. Shutters.rot- a framing shutters module fine rotation (value range: 0-255)
Fr. Shutter 1 Move - a Fram. lamella 1 fine moving
Fr. Shutter 1 Swiv. - a Fram. lamella 1 fine swivelling
Fr. Shutter 2 Move - a Fram. lamella 2 fine moving
Fr. Shutter 2 Swiv.- a Fram. lamella 2 fine swivelling
Fr. Shutter 3 Move - a Fram. lamella 3 fine moving
Fr. Shutter 3 Swiv. - a Fram. lamella 3 fine swivelling
Fr. Shutter 4 Move - a Fram. lamella 4 fine moving
Fr. Shutter 4 Swiv. - a Fram. lamella 4 fine swivelling
Calibration of the effects via the control board
1. Disconnect DMX controller from the fixture and enter the "Calibrate Effects" menu.
2. Use the [up arrow] and [down arrow] to find "Pan" and touch it to enter the fine effect adjustment screen.
3. Set desired value and save it by touching the [confirm].
4. Repeat steps 2 and 3 for next item
5. After calibrating all effects, touch the [confirm] to save all adjusted values and reset the fixture.
Calibration of the effects via the DMX controller
1. Connect DMX controller to the fixture and enter the "Calibrate Effects" menu.
Calibration protocol:
Effect
Mode 1
Mode 2
Panchannel 50channel 43
Tilt channel 51
channel 44
Ef. wheel
channel 52
channel 45
Rot. Gobo Wheel
channel 53
channel 46
R. Gobo Index 1
channel 54
channel 47
R. Gobo Index 2
channel 55
channel 48
R. Gobo Index 3
channel 56
channel 49
R. Gobo Index 4
channel 57
channel 50
R. Gobo Index 5
channel 58
channel 51
R. Gobo Index 6
channel 59
channel 52
R. Gobo Index 7
channel 60
channel 53
Static gobo
channel 61
channel 54
Colour wheel 1
channel 62
channel 55
Colour wheel 2
channel 63
channel 56
Prism 1
channel 64
channel 57
Prism 2
channel 65
channel 58
Zoomchannel 66channel 59
Focuschannel 67channel 60
Irischannel 68channel 61
Frost 1/1
channel 69
channel 62
Frost 1/2
channel 70
channel 63
Frost 2/1
channel 71
channel 64
Frost 2/2
channel 72
channel 65
Fr. Shutters rot.
channel 73
channel 66
Fr. Shutter 1 Move
channel 74
channel 67
Fr. Shutter 1 swiveling. channel 75
channel 68
Fr. Shutter 2 Move
channel 76
channel 69
Fr. Shutter 2 swiveling channel 77
channel 70
Fr. Shutter 3 Move
channel 78
channel 71
30
Fr. Shutter 3 swiveling channel 79
Fr. Shutter 4 Move
channel 80
Fr. Shutter 4 swiveling channel 81
channel 72
channel 73
channel 74
Calibrate Fr. Hysteresis
Framing Lamella 1 - a framing lamella 1 reverse movement (value range: 0-8)
Framing Lamella 2 - a framing lamella 1 reverse movement (value range: 0-8)
Framing Lamella 3 - a framing lamella 1 reverse movement (value range: 0-8)
Framing Lamella 4 - a framing lamella 1 reverse movement (value range: 0-8)
The value set for every framing lamella gives a value at which the lamella reacts to its reverse
movement promptly (without movement hysteresis).
Calibrate Pan/Tilt EMS - This menu item allows calibration of the pan/tilt electronic motion stabilizer.
Important: during this calibration any external force must not influence the fixture and the surface at which
the fixture stands (or truss if the fixture hangs) has to be without movement, shake, strokes etc.
Load Default Calibrations - The item loads default (factory) calibration values.
Rotating Gobos Change - This menu makes changing of rotating gobos in the fixture easier.
Gobo Carousel 1 - The menu allows movement of rotating gobos to the positions suitable for their changing.
G1-Mg - a movement of the gobo 1 (gobo holder with magnet) to the changing position.
G2 - a movement of the gobo 2 to the changing position.
:
G7 - a movement of the gobo 7 to the changing position.
Gobo Offset -a gobo offset setting. The function allows fine swiveling of the gobo holder. The set value
is valid for all gobos on the gobo carousel.
LEDs Measure - This menu item runs a procedure which measures a light intensity of the LEDs module installed
in the fixture. This procedure takes about 1 minute (message " LEDs Module Measurement" is displayed on
the screen"). During the procedure the fixture does not receive DMX signal, pan/tilt go to 128 DMX, a shutter
is open and a dimmer is set at max. light intensity (255 DMX). All effects are taken out from the light beam.
The measured light intensity is recorded in the item Intensity in the menu LED Module Info:
Tab Information --> Actual Module Info --> Intensity
Tab Information --> Intensity History --> Intensity
The light intensity in the menu item Intensity is displayed in percentages in relation to the initial intensity of the
new LEDs module (initial intensity=100%).
The LEDs Measure procedure should be run after every change of the LED light source.
Note: The fixture has to be connected to mains in order to run LEDs Measure procedure.
Update software - The menu item allows you to update software in the fixture.
The following items are required in order to update software:
- PC running Windows or Linux or macOS
- DSU file
- Flash cable RS232/DMX, P/N13050624 (if you want to use a serial port of PC)
- Robe Universal Interface or Robe Universal interface WTX (if you want to use an USB port of PC)
After the software updating the fixture will be set to default values.
To update software in the fixture:
1. DSU file is available from Robe web site at WWW.robe.cz.
File with extension zip is intended for Windows (used and tested from XP to W10 on 32/64bit systems).
File with extension tbz is intended for Linux (used and tested on Debian and Ubuntu 32/64bit).
File with extension dmg is intended for macOS (used and tested on OSX up to Sierra) XQuartz required,
install it from https://www.xquartz.org/
Save the download file to a folder on your computer.
In case that you use windows, extract files in the zip file (e.g. DSU_RobinEsprite_18100828.zip)
2. Disconnect the fixture from DMX controller.
3. If you use the flash cable RS232/DMX, connect a serial port of your computer with DMX input of the fixture
by means of the cable.
If you use the Robe Universal Interface, connect a USB port of your computer with the Robe Universal Interface
by means of the USB cable and DMX input of the fixture with the DMX output of the Robe Universal Interface
via a DMX cable.
4. Switch the fixture to the update mode (tab "Service" --> Update Software).
31
Note: If you do not want to continue in the software update, you have to switch off and on the fixture
to escape from the updating mode.
We recommend to cancel all running programs on your computer before starting the software update.
5. Double-click the software uploader file (e.g. DSU_RobinEsprite_18100828.exe) in
the extracted files. The Software Uploader program will start running.
6. Select correct "COM " number if you use a Flash cable RS232/DMX or select "Robe Universal Interface "
if you use the Robe Universal Interface/Robe Universal Interface WTX and then click on the "Connect" button.
7. If the connection is OK, click the “Start Uploading" button to start software uploading. It will take several
minutes to perform software update.
If the option "Incremental Update" is not checked, all processors will be updated (including processors with
the same software version).
If you wish to update only processors with new version of software, check the “Incremental Update box“.
Avoid interrupting the process. Update status is being displayed in the "Info Box" window.
When the update is finished, the line with the text “Fixture is successfully updated“ will appear in
this window.
In case upload process is interrupted (e.g. power loss), the fixture stays in “Updating mode” and you will have
to repeat the software update again.
Another way, how to update software in the fixtures (especially large installation of fixtures) is to use the ROBE
Uploader. It is a software for automatized software update of Robe fixtures. It takes advantage of RDM
support).
For more information please see https://www.robe.cz/robe-uploader/.
32
8. RDM
This fixture supports RDM operation. RDM (Remote Device Management) is a bi-directional communications
protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and
status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting
existing non-RDM equipment. By using a special „Start Code,“ and by complying with the timing specifications
for DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive
messages from specific moving lights.
RDM allows explicit commands to be sent to a device and responses to be received from it.
The list of commands for Robin Esprite is the following:
Parameter ID
Discovery command SET command
DISC_UNIQUE_BRANCH
*
DISC_MUTE
*
DISC_UN_MUTE
*
GET command
DEVICE_INFO
*
SUPPORTED_PARAMETERS
*
SOFTWARE_VERSION_LABEL
*
DMX_START_ADDRESS
*
*
IDENTIFY_DEVICE
*
*
DEVICE_MODEL_DESCRIPTION
*
MANUFACTURER_LABEL
*
*
DEVICE_LABEL
*
SENSOR_DEFINITION
*
SENSOR_VALUE
*
DISPLAY_INVERT
*
*
DISPLAY_LEVEL
*
*
PAN_INVERT
*
*
TILT_INVERT
*
*
DEVICE_RESET
*
DMX_PERSONALITY
*
*
DMX_PERSONALITY_DESCRIPTION
*
STATUS_MESSAGES
*
STATUS_ID_DESCRIPTION
*
RDM model ID for the Robin Esprite is 0x0107.
33
9. Error and information messages
Information icons
- Air Filters Cleaning
This icon signalizes that cleaning period of the air filters has elapsed
and you have to clear air filters and reset the menu item "Elapsed Time".
Errors
Error in the fixture is signalled by the yellow warning icon at the bottom line of the screen:
Touch the warning icon or press the [ESCAPE] button to display error messages.
List of error and information messages:
Tilt Error 1 (Tilt Error 2)
This message will appear after the reset of the fixture if the head´s magnetic-indexing circuit malfunctions
(sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The head
is not located in the default position after the reset.
Pan Error 1 (Pan Error 2)
This message will appear after the reset of the fixture if the yoke´s magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The yoke is not
located in the default position after the reset of the fixture.
Prism Error 1 (Prism Error 2 )
The messages will appear after the reset of the prism wheel if this wheel is not located in the default position.
Iris Error 1 (Iris Error 2 )
The messages will appear after the reset of the iris if the iris is not located in the default position.
Frost 1 Error 1 (Frost 1 Error 2 )
The messages will appear after the reset of the light frost module if this module is not located in the default
position.
Frost 2 Error 1 (Frost 2 Error 2 )
The messages will appear after the reset of the medium frost module if this module is not located in the default
position.
Zoom Error 1 (Zoom Error 2 )
The messages will appear after the reset of the zoom module if the zoom lens is not located in the default position.
Focus Error 1 (Focus Error 2 )
The messages will appear after the reset of the focus module if the focus lens is not located in the default.
Gobo Carousel Error 1 (Gobo Carousel Error 2 )
The messages will appear after the reset of the rotating gobo wheel if this wheel is not located in the default
position.
Gobo Rotation Error 1 (Gobo Rotation Error 2 )
The messages will appear after the reset of the rotating gobo wheel if the rotating gobos are not located in the
default positions.
Effect Wheel Error 1 (Effect Wheel Error 2 )
The messages will appear after the reset of the effect wheel if this wheel is not located in the default position
34
Fr. Shutters Rot. Error 1 (Fr. Shutters Rot. Error 2 )
The messages will appear after the reset of the framing shutters module if this module is not located in the
default position.
Fr. Shutter 1 Error 1 (Fr. Shutter 1 Error 2 )
The messages will appear after the reset of the framing shutters module if the frame 1 is not located in the
default position.
Fr. Shutter 2 Error 1 (Fr. Shutter 2 Error 2 )
The messages will appear after the reset of the framing shutters module if the frame 2 is not located in the
default position.
Fr. Shutter 3 Error 1 (Fr. Shutter 3 Error 2 )
The messages will appear after the reset of the framing shutters module if the frame 3 is not located in the
default position.
Fr. Shutter 4 Error 1 (Fr. Shutter 4 Error 2 )
The messages will appear after the reset of the framing shutters module if the frame 4 is not located in the
default position.
EEprom Error
Hardware error of the EEprom.
Recharge The battery
The battery on the display board needs to be charged. Let the fixture on for cca 6 hrs.
Battery Faulty. Replace it.
The battery on the display board is exhausted and should be replaced immediately.
Pan/Tilt EMS Cal. Error
The EMS system is not calibrated.
Pan/Tilt EMS Error
Control electronics cannot communicate with the EMS system.
Internal Error 1
Communication error between PCBs (error or noise was detected on communication wires)
Internal Error 2
Communication error (some PCB has failed or is disconnected (this PCB will show as N/A in menu --> Information --> Software versions) or error/noise was detected on communication wires)
Clean Air Filters
The message informs you that the item "Elapsed Time" in the "Fixture Information" menu is at 0 value. Clean
air filters and reset this counter.
Overheated
The LED engine is overheated and light output is closed.
Base Fan Bad
One or both fans in the fixture base are disconnected from their control PCB or are faulty and has to be replaced. .
Fan 1 Bad/Fan 2 Bad/Fan 3 Bad
The suction fan 1 (fan 2/ fan 3) at the LED engine is disconnected from its control PCB or is faulty and has to
be replaced.
Fan 4 Bad/ Fan 5 Bad/ Fan 6 Bad
The exhaust fan 4 (fan 5/ fan6) at the LED engine is disconnected from its control PCB or is faulty and has to
be replaced.
35
Positions of cooling fans, their control PCBs and control processors:
36
10. Technical Specifications
Electrical
Power supply: electronic auto-ranging
Input voltage range: 100-240V, 50-60Hz
Fuse: T 12 A
Max. power consumption: 950W (Power factor 0.98)
Optic
Light source: TE™ 650W White LED Engine (Transferable)
Colour temperature: 6700K
CRI: 70 (standard), 80 or 90 by means of CRI filters on the colour wheel 2
Light source warranty: 3 years or 20 000 hours
Colour wheel 1
five dichroic filters (deep red, deep blue, orange, green, congo blue) + open
Colour wheel 2
one multicolour filter, two dichroic filters (lavender, laser green), CRI filter 80, CRI filter 90
+ open
CMY + CTO mixing module
Smooth CMY colour mixing system
Variable CTO: 3000K - 6.700K
Virtual colour wheel
Effect wheel
66 preset colours
Aluminium effect wheel rotating in both directions with variable speed
Static gobo wheel
9 replaceable gobos, outside diameter: 26.8+0,1 mm, image diameter=23.5 mm, high temperature
borofloat or better glass, thickness=1.1-3.5 mm
Gobo wheel continuous rotation
Gobos order:
Note. Metal (or aluminium) gobos cannot be used due to thermal stress.
Rotating gobo wheel
7 replaceable gobos can be indexed and rotated in both directions at different speeds
Gobo carousel continuous rotation,
Gobos: outside diameter= 26.8+0,1 mm, image diameter=23.5 mm, thickness=1.1-3.5 mm, high
temperature borofloat or better glass. Do not use steel gobos 0.15mm
"Slot&lock" system for easy replacement of gobos
Gobos order:
Note. Metal (or aluminium) gobos cannot be used due to thermal stress.
37
Prism
Rotating 6-facet prism with continuous rotation in both directions
Iris
Motorized iris for different beam diameters
Frost filters
2 separate,variable frost filters ( light (1°) and medium (5°))
The medium filter is replaceable
Framing shutters module
Zoom
Strobe
Dimmer
4 individually positionable blades plus rotation of the complete frame system +/- 60°
Each framing shutter can move up to 80% of the beam and swivel +/- 30°
Linear motorized zoom
Min. beam angle :5.5°
Max. beam angle: 49°
Strobe effect with variable speed (0.3 - 20Hz)
Smooth dimmer from 0 - 100 % (8 or 16 bit (internal 18 bit))
Camera (Robin Esprite FS only)
Type: SNZ-6320
Max. resolution: 1920 x 1080
16 : 9 Full HD (1080p) resolution support
32x optical zoom, 16x digital zoom
H.264, MJPEG dual codec, Multiple streaming
Day & Night (ICR), WDR (120dB)
Control
Graphic touch screen for fixture setting and addressing
Gravitation sensor for auto screen positioning
Battery backup of the touch screen
Readout fixture and LEDs usage, receiving DMX values, temperatures, etc
Built-in analyzer for easy fault finding, error messages
Built-in demo sequences
Stand-alone operation
2 user editable programs, each up to 80 steps
Supported protocols: USITT DMX 512-A, RDM, ArtNet, MANet, MANet2, sACN
Support of RDM (Remote Device Management)
2 DMX modes (49, 42 control channels)
Wireless DMX/RDM module
Compliance with USITT DMX-512 (1986 & 1990) and 512-A
Full DMX fidelity and frame integrity
Auto sensing of DMX frame rate and frame size
<5ms DMX latency
Operational frequency range of 2402-2480 MHz
Producer: LumenRadio
Pan/Tilt
Pan movement range 540°
Tilt movement range 280°
16 bit movement resolution
38
Pan/Tilt electronic motion stabilizer
Automatic Pan/Tilt position correction
Remotely controllable speed of pan/tilt movement for easy programming
Pan/tilt-lock mechanism
Connection
Rigging
DMX data in/out: Locking 3-pin and 5-pin XLR
AC power input: Chassis connector Neutrik PowerCon TRUE 1, NAC3MPX
Mounting points: 2 pairs of 1/4-turn locks
Mounting horizontally or vertically via 2 Omega brackets
Temperatures
Maximum/Minimum ambient operating temperature : +45°C/-5°C
Maximum housing temperature : 70° C
Minimum distances
Min. distance from flammable surfaces: 1 m
Min. distance to lighted object: 3 m
Total heat dissipation
3240 BTU/hr (calculated)
Ingress protection rating
IP20
Weight
28.2 kg (Robin Esprite)
29.4 kg (Robin Esprite FS)
39
Dimensions (mm) Robin Esprite
40
Robin Esprite FS
Gel Frame Adaptor Esprite (P/N 10980463)
Gel Frame Esprite (P/N 10980464)
Accessories
1 x Omega Adaptor Tall CL-regular 2 pcs in box (P/N 10980501)
1 x Power cable including powerCON TRUE1 In connector
1 x Hot-spot lens (P/N 10980483) Optional accessories
Gel Frame Adaptor Esprite (P/N 10980463)
Gel Frame Esprite (P/N 10980464)
Top hat Esprite (P/N 10980465)
Doughty Trigger Clamp (P/N 17030386)
LED light source for Esprite (P/N 14080066)
Safety wire 35 kg (P/N 99011963)
Frost filter 10° assembled (P/N 10980497)
Upgrade kit CRMX Universal 260 (P/N 99030100)
Omega adaptor CL-regular 2 pcs in box (P/N 10980033)
Robin Esprite LightMaster Side kit SET (P/N 10080332)
41
11. Photometric diagrams
42
43
44
45
46
47
48
49
50
12. Maintenance and cleaning
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build
up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will
not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances
should alcohol or solvents be used!
DANGER !
Disconnect from the mains before starting any
maintenance work
The front objective lens will require weekly cleaning as smoke-fluid tends to building up residues, reducing the
light-output very quickly. The cooling-fans should be cleaned monthly.
The interior of the fixture should be cleaned at least annually using a vacuum-cleaner or an air-jet.
Gobo wheels and the internal lenses should be cleaned monthly.
Remove dust and dirt from the fans and cooling vents using a soft brush and vacuum-cleaner.
Important! Check the air filters periodically and clean before they become clogged!
Clean the air filters placed in the base. Use a vacuum cleaner, compressed air or you can wash them and put
back dry.
After replacing the air filters, reset the elapsed time counter in the menu "Information"
(Information--->Air Filters---> Elapsed Time).
Replacing the fuse.
Before replacing the fuse, unplug mains lead.
1. Remove the fuse holder on the rear panel of the base with a fitting screwdriver from the housing
(anti-clockwise).
2. Remove the old fuse from the fuse holder.
3. Install the new fuse in the fuse holder (only the same type and rating).
4. Replace the fuseholder in the housing and fix it.
Checking plastic parts of the fixture.
The plastic parts of the fixture should be checked for damages and beginning cracks at least every two months.
In addition, the plastic part of the front lens has to be checked mechanically (by means of movement by the
plastic part) if it is firmly fastened to the fixture. If hint of a crack is found on some plastic part, do not use the
fixture until the damaged part will be replaced.
Cracks or another damages of the plastic parts can be caused by the fixture transportation or manipulation and
also ageing process may influence plastic materials.
This checking is necessary for both fixed installations and preparing fixtures for renting. Any free moving parts
inside of the fixture head, cracked plastic or any plastic part of front lens not sitting properly in place need to
be immediately replaced.
12.1 Disposing of the product
To preserve the environment please dispose or recycle this product at the end of its life according to the local
regulations and codes.
51
13. ChangeLog
This section summarizes changes in the user manual.
Version of the
manual
Date of issue
Description of changes
1.1
11/09/2019
Accessories changed
1.2
12/09/2019
High-power Mode added
1.3
03/10/2019
DMX chart ver. 1.2. (virtual colour wheel -colours specified).
1.4
08/10/2019
Changing the LED source added.
1.5
14/10/2019
DMX chart ver. 1.3. (framing shutter swivelling 30°)
1.6
17/10/2019
Version "Esprite FS" added
1.7
30/10/2019
DMX chart ver. 1.4 (CTC range changed 6700K-3000K)
1.8
20/11/2019
Hot-spot lens added to Optional accessories
1.9
29.11/2019
Optional accessories specified
2.0
06/01/2020
Frost filter 10° - new P/N 10980497
2.1
20/01/2020
Warning "Risk group 2, RG-2 " added
2.2
14/02/2020
Gel frame installation added
2.3
18/02/2020
LED Module Info added (tab Information)
2.4
03/03/2020
Obtaining information about the LED light source by mobile phone
2.5
11/03/2020
Follow spot mode added (tab Personality)
2.6
31/03/2020
DMX chart ver. 1.5 (Virtual colours more specified)
March 31, 2020
Copyright © 2018-2020 Robe Lighting - All rights reserved
All Specifications subject to change without notice
Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici
52
14. Appendix
14.1Changing the LED light source
The Robin Esprite allows you to change the LED light source and this way keep a high performance of the fixture.
To change the LED light source.
1. Disconnect the fixture from mains and allow it to cool about 30 minutes.
2. Remove top covers of the fixture and lock the head in a horizontal position in which you will have access to
the control PCB (1) of the LED source.
3. Disconnect both LED source connectors (2) from the LED control PCB (1).
1
2
2
4. Unscrew two screws M3x12 with star washers (3) on each side of the rear cover (4) of the head and remove
the cover (4).
3
4
3
53
5. Unscrew the four socket head screws M4x16 (use Allen key 3) with plain washers (5) and remove the LED
source module (6) from the head. Be careful, the LED source module is heavy.
5
5
6
5
5
Fixture head without LED source module.
54
The new LED light source includes PCB with LEDs, connecting cables with connectors and the heat sink.
Handle with care. Do not touch LEDs with bare hands.
6. To install the new LED source module, proceed in a reverse order than at its dismantling, i.e. screw the LED
source module (6) to the head, screw the rear cover (4) to the head and connect the connectors from the LED
source module to the LED control PCB (1).
Placing of the LED source module cable:
55
Note for mounting of the rear cover (4).
After placing the rear cover (4) on the head, do not fully tighten the screws (3) in the holes with M3 thread (7)
We recommend you to install one or both plastic covers (8) on the head, check that cover (s) properly fits to
the rear cover (4) and then fully tighten the rear cover screws (3).
7
9
7
There can be a space (about 1 mm) between the rear cover (4) and the side cover (9).
8
3
4
9
3
After finishing the LED source module installation and placing all covers back on the fixture, connect the fixture
to mains and run the procedure LEDs Measure from the tab Service.
56
14.2. Obtaining information about the LED light source by mobile phone
You can read information about the LED light source by means of the mobile application ROBE COM. The LED
light source has to be outside of the fixture.
Download and install the application ROBE COM from Google Play (for Android 5.0 and higher) or App Store (for
iOS 12.0 and higher) to your mobile phone. Your mobile phone has to support NFC (Near-Field Communication).
After installing the ROBE COM, run the application by touching the icon
The following screen will appear:
.
Hold the mobile phone close to the point of the LED light source PCB which is marked with the symbol NFC.
57
If NFC connection is OK, the screen with RDM UID of the LED light source will appear.
Touch the LED engine and the screen with LED light source information will appear.
The button READ loads data from another LED light source. The button WRITE does not have any function.
If you touch the READ button to load data from another LED light source, the warning message will appear.
If you select the option DISCARD, originally loaded data will be overwritten.
58
DMX protocol
Robin Esprite TM - DMX protocol
Version: 1.5 Mode 1 - Standard 16 bit, Mode 2 - Reduced 8 bit
Quick overview of default DMX values for each channel
Mode/channel
1
2
Default
DMX Value
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
1
2
3
4
5
6
7
8
9
10
*
11
*
12
13
14
15
16
17
18
19
20
21
22
23
24
25
*
26
27
28
29
*
30
*
31
*
32
33
34
35
36
128
0
128
0
0
0
10
128
0
0
0
0
0
0
0
0
0
0
0
0
0
0
128
0
0
0
128
0
0
128
0
0
0
128
0
128
0
128
0
128
0
128
43
37
0
Function
Pan
Pan Fine
Tilt
Tilt fine
Pan/Tilt speed , Pan/Tilt time
Power/Special functions
LED frequency selection
LED frequency fine adjusting
Max. light intensity indication and setting
Colour wheel 1
Colour wheel 1-fine positioning
Colour wheel 2
Colour wheel 2-fine positioning
Cyan
Magenta
Yellow
CTO
Virtual colour wheel
Effects speed
CMY+CTO+Colour wheels time
Static gobo/ Framing shutters/Zoom/Focus/Iris/Frost/Prism time
Effect wheel positioning
Effect wheel rotation
Effect wheel animations
Static gobo wheel
Rotating gobo wheel
Rot. gobo indexing and rotation
Rot. gobo indexing/rotation - fine
Prism
Prism indexing/rotation
Frost
Iris
Iris - fine
Zoom
Zoom - fine
Focus
Focus - fine
Framing shutters module rotation
Framing shutter 1- movement
Framing shutter 1- swivelling
Framing shutter 2- movement
Framing shutter 2- swivelling
Framing shutter 3 movement
Page 1
DMX protocol
Mode/channel
1
2
44
45
46
47
48
49
38
39
40
41
42
*
Mode/channel
1
2
1
1
2
2
Default
DMX Value
128
0
128
32
0
0
4
5
5
Type of
control
Pan movement by 540° (128=default)
proportional
Pan Fine
0 - 255
Fine control of pan movement (0=default)
0 - 255
Tilt movement by 280° (128=default)
proportional
Tilt
proportional
Tilt fine
0 - 255
Fine control of tilt movement (0=default)
proportional
Pan/Tilt speed , Pan/Tilt time
0
1
2 - 255
2 - 255
6
Function
Pan
3
4
Framing shutter 3- swivelling
Framing shutter 4 movement
Framing shutter 4- swivelling
Shutter/ strobe
Dimmer intensity
Dimmer intensity - fine
DMX
Value
0 - 255
3
Function
Standard mode (0=default)
Max. Speed Mode
Pan/Tilt speed mode
Speed from max. to min.
Pan/Tilt time mode
Time from 0.2 sec. to 25.5 sec.
step
step
proportional
proportional
Power/Special functions
6
Factory display menu setting: DMX Input-Wired ,Graphic displayOn, Pan/tilt Mode-Speed,Blackout while pan/tilt moving-Off,
Blackout while gobo wheels moving-Off,Blackout while colour
wheels moving-Off, Fans mode-Auto, High-power mode Off
0 -9
10-14
15-19
Reserved (0=default)
To activate following functions, stop in DMX value for at least 3 s and
shutter must be closed at least 3 sec. (Channel „Shutter/ Strobe” 47/41
must be at range: 0-31 DMX). Corresponding menu items are temporarily
overwritten.
DMX input: Wired DMX *
DMX input: Wireless DMX *
step
step
* function is active only 10 seconds after switching the fixture on
20-24
25-29
30-39
40-44
45-49
50-54
55-59
60-64
65-69
70-74
Graphic display: On
Graphic display: Off
Reserved
step
Pan/Tilt mode: Speed
Pan/Tilt mode: Time
Blackout while pan/tilt moving: On
Blackout while pan/tilt moving: Off
Blackout while gobo wheels moving: On
Blackout while gobo wheels moving: Off
Blackout while colour wheels moving: On
step
step
Page 2
step
step
step
step
step
step
DMX protocol
Mode/channel
1
2
DMX
Value
75-79
80-84
85-89
90-94
95-99
100-109
110-114
115-119
120-124
125-129
Function
Blackout while colour wheels moving: Off
Fans mode: Auto
Fans mode: High
High-power mode: On
High power mode: Off
Reserved
Dimmer curve: Square law
Dimmer curve: Linear
Parking position: On
Parking position: Off
Type of
control
step
step
step
step
step
step
step
step
step
To activate following functions, stop in DMX value for at least 3 seconds.
130 - 139
140 - 149
150 - 159
160 - 169
170 - 179
180 - 189
190 - 199
200 - 209
210-224
Fixture reset (except pan/tilt)
Pan/Tilt reset
Colour system reset
Gobo wheels/effect wheel reset
Reserved
Zoom/focus/frost/prism reset
Iris /framing shutters reset
Total fixture reset
Reserved
step
step
step
step
step
step
The following RoboSpot related commands are only applicable when the RoboSpot
is connected:
225 - 229
230 - 234
235 - 239
240
241 - 255
7
RoboSpot enabled
RoboSpot disabled - except handle faders and pan/tilt
RoboSpot fully disabled
Disabled "Quiet mode"
Quiet mode - fan noise control from min. to max.
step
step
step
step
proportional
LED frequency selection
Factory display menu setting: 600Hz
7
Select PWM output frequency of LEDs. Selected PWM frequency can be
fine adjusted in 127 steps up/down around selected PWM frequency on
the channel below. Corresponding menu item (Frequency Setup) is
temporarily overridden.
0-4
5-9
10-14
15-19
20-24
25-255
PWM frequency from Display menu (fixture utilizes PWM
frequency set in the display menu item Frequency Setup).
step
300 Hz
600 Hz (10=default)
1200 Hz
2400 Hz
Reserved (fixture utilizes PWM frequency set in the display menu item
step
step
step
step
Frequency Setup).
8
LED frequency fine adjusting
Factory display menu setting: 600Hz
8
Select desired PWM output frequency of LEDs on the channel above.
0-1
2
3
4
:
Selected LED Frequency
LED Frequency (step -126)
LED Frequency (step -125)
LED Frequency (step -124)
step
step
step
step
Page 3
DMX protocol
Mode/channel
1
2
DMX
Value
125
126
127
128
129
130
131
:
252
253
254
255
9
9
0-10
11-20
Function
Type of
control
LED Frequency (step -3)
LED Frequency (step -2)
LED Frequency (step -1)
step
Selected LED Frequency (128=default)
step
LED Frequency (step +1)
LED Frequency (step +2)
LED Frequency (step +3)
step
LED Frequency (step +124)
LED Frequency (step +125)
LED Frequency (step +126)
Selected LED Frequency
Max. light intensity indication and setting
No function (0=default)
Indication of drop of max. light intensity
step
step
step
step
step
step
step
step
step
A drop of max. light intensity of the fixture (compared to its
original intensity) is indicated by a corresponding colour output:
0-5%, (WHITE /new LED module/)
6-10% (RED)
11-15% (GREEN)
16-20% (BLUE )
21-25% (CYAN )
26-30% (MAGENTA)
31-35% (YELLOW)
36-40% (ORANGE)
Pan/tilt/zoom is set at 128 DMX (50%), Dimmer is open at 255
DMX (100%).
To set a drop of max. light intensity (compared to original light
intensity), stay at DMX value for at least 3 sec. and shutter must
be closed at least 3 sec. (Channel „Shutter/ Strobe” 47/41 must be
at range: 0-31 DMX). Corresponding menu items are permanently
overwritten.
21-30
31-40
41-50
51-60
61-70
71-80
81-90
91-100
101-255
10
Set drop by 6-10% (RED)
Set drop by 11-15% (GREEN)
Drop by 16-20% (BLUE)
Set drop by 21-25% (CYAN)
Set drop by 26-30% (MAGENTA)
Set drop by 31-35% (YELLOW)
Set drop by 36-40% (ORANGE)
Original intensity (WHITE)
Reserved
step
step
step
step
step
step
step
step
Colour wheel 1
10
0
21
43
64
86
Continual positioning
Open/white (0=default)
Deep red
Deep blue
Orange
Green
proportional
proportional
proportional
proportional
proportional
Page 4
DMX protocol
Mode/channel
1
2
DMX
Value
Function
107
Congo blue
128-129 Open/White
Positioning
130-141 Deep red
142-153 Deep blue
154-165 Orange
166-177 Green
178-189 Congo blue
190 - 215 Forwards rainbow effect from fast to slow
216 - 217 No rotation
218 - 243 Backwards rainbow effect from slow to fast
244 - 249 Random colour selection by audio control
(Set microphone sensitivity in menu „Personality”)
250 - 255 Auto random colour selection from fast to slow
11
130-141
142-153
154-165
166-177
178-189
190 - 215
216 - 217
218 - 243
244 - 249
250 - 255
0 - 255
12
15
13
15
18
16
step
step
step
proportional
step
proportional
step
proportional
Fine positioning (0=default)
proportional
Continual positioning
Open/white (0=default)
Multicolour
Laser green
Lavender
Filter CRI 80
Filter CRI 90
Open/White
Positioning
Multicolour
Laser green
Lavender
Filter CRI 80
Filter CRI 90
Forwards rainbow effect from fast to slow
No rotation
Backwards rainbow effect from slow to fast
Random colour selection by audio control
(Set microphone sensitivity in menu „Personality”)
Auto random colour selection from fast to slow
proportional
proportional
proportional
proportional
proportional
proportional
step
step
step
step
step
step
proportional
step
proportional
step
proportional
Fine positioning (0=default)
proportional
Cyan from min. saturation --> full cyan (0=default)
proportional
Magenta
0 - 255
Magenta from min. saturation --> full magenta (0=default)
0 - 255
Yellow from min. saturation --> full yellow (0=default)
proportional
Yellow
14
17
step
Cyan
0 - 255
16
step
Colour wheel 2 - fine positioning
*
14
step
Colour wheel 2
11
0
21
43
64
86
107
128-129
13
proportional
Colour wheel 1 - fine positioning
*
0 - 255
12
Type of
control
proportional
CTO filter
0 - 255
CTO from 6700K --> 3000K (0=default)
Virtual colour wheel
Page 5
proportional
DMX protocol
Mode/channel
1
2
DMX
Value
0
1-2
3-4
5-6
7-8
9-10
11-12
13-14
15-16
17-18
19-20
21-22
23-24
25-26
27-28
29-30
31-32
33-34
35-36
37-38
39-40
41-42
43-44
45-46
47-48
49-50
51-52
53-54
55-56
57-58
59-60
61-62
63-64
65-66
67-68
69-70
71-72
73-74
75-76
77-78
79-80
81-82
83-84
85-86
87-88
89-90
91-92
93-94
Function
No function (0=default)
Filter 4 (Medium Bastard Amber)
Filter 10 (Medium Yellow)
Filter 19 (Fire)
Filter 26 (Bright Red)
Filter 58 (Lavender)
Filter 68 (Sky Blue)
Filter 71 (Tokyo Blue)
Filter 79 (Just Blue)
Filter 88 (Lime Green)
Filter 90 (Dark Yellow Green)
Filter 100 (Spring Yellow)
Filter 101 (Yellow)
Filter 102 (Light Amber)
Filter 103 (Straw)
Filter 104 (Deep Amber)
Filter 105 (Orange)
Filter 106 (Primary Red)
Filter 111 (Dark Pink)
Filter 115 (Peacock Blue)
Filter 116 (Medium Blue-Green)
Filter 117 (Steel Blue)
Filter 118 (Light Blue)
Filter 119 (Dark Blue)
Filter 120 (Deep Blue)
Filter 121 (Filter Green)
Filter 128 (Bright Pink)
Filter 131 (Marine Blue)
Filter 132 (Medium Blue)
Filter 134 (Golden Amber)
Filter 135 (Deep Golden Amber)
Filter 136 (Pale Lavender)
Filter 137 (Special Lavender)
Filter 138 (Pale Green)
Filter 139 (Primary Green)
Filter 141 (Bright Blue)
Filter 147 (Apricot)
Filter 148 (Bright Rose)
Filter 152 (Pale Gold)
Filter 154 (Pale Rose)
Filter 157 (Pink)
Filter 158 (Deep Orange)
Filter 162 (Bastard Amber)
Filter 164 (Flame Red)
Filter 165 (Daylight Blue)
Filter 169 (Lilac Tint)
Filter 170 (Deep Lavender)
Filter 172 (Lagoon Blue)
Page 6
Type of
control
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
DMX protocol
Mode/channel
1
2
DMX
Value
95-96
97-98
99-100
101-102
103-104
105-106
107-108
109-110
111-112
113-114
115-116
117-118
119-120
121-122
123-124
125-126
127-128
129-130
131-132
133-255
19
24
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
Speed of CMY+CTO movement from max. to min. (0=default)
Speed of Rot. Gobo/Stat. Gobo selection from max. to min.
proportional
proportional
Function is off (0=default)
step
Time of CMY, CTO and Colour wheels movement (0.1sec-->25.5sec.)
proportional
Static gobo wheel/ Framing
shutters/Zoom/Focus/Iris/Frost/Prism time
19
1-50
23
step
CMY+CTO+Colour wheels time
18
0
1-255
1 - 255
22
step
Speed of CMY&CTO movement and Rot. Gobo/Static Gobo
selection
0
1 - 255
21
Filter 179 (Chrome Orange)
Filter 180 (Dark Lavender)
Filter 181 (Congo Blue)
Filter 197 (Alice Blue)
Filter 201 (Full C.T. Blue)
Filter 202 (Half C.T. Blue)
Filter 203 (Quarter C.T. Blue)
Filter 204 (Full C.T. Orange)
Filter 205 (Half C.T. Orange)
Filter 206 (Quarter C.T. Orange)
Filter 247 (Filter Minus Green)
Filter 248 (Half Minus Green)
Filter 281 (Three Quarter C.T. Blue)
Filter 285 (Three Quarter C.T. Orange)
Filter 352 (Glacier Blue)
Filter 353 (Lighter Blue)
Filter 715 (Cabana Blue)
Filter 778 (Millennium Gold)
Filter 793 (Vanity Fair)
Reserved
Type of
control
Effects Speed
17
0-255
0-255
20
Function
Function is off (0=default)
step
Time of Static gobo movement (0.1 sec-->25.5 sec.)
proportional
Time of framing shutters, zoom, focus, iris and frost movement (0.1
proportional
sec-->25.5 sec.)
Time of prism movement (0.1 sec-->5 sec.)
proportional
Effect wheel positioning
20
0-19
20-127
128-170
171-213
214-255
No function (0=default)
Proportional indexing (73-center)
Ramping from open to full position ( max--->min. speed)
Ramping from open to half position ( max. --->min. speed)
Ramp. from half position to full position ( max. --->min. speed)
0
1 - 127
128
129 - 255
No rotation
Forwards rotation from fast to slow
No rotation (128=default)
Backwards rotation from slow to fast
step
proportional
proportional
proportional
proportional
Effect wheel rotation
21
Effect wheel animations
22
0-7
No animation (0=default)
Page 7
step
proportional
step
proportional
DMX protocol
Mode/channel
1
2
DMX
Value
Function
Type of
control
Note : Set suitable DMX value at Focus channel to get desired
animation. All animations were created at distance of 5 m from screen
with zoom=128 DMX, Focus value is different for each effect (focus value is
stated in parentheses for this distance)
The following channels are blocked: Effect wheel positioning, Effect
wheel rotation,Static gobo wheel. Rotating gobo wheel, Rot. Gobo
indexing and rotation, Rot. Gobo wheel fine rotation.
8-9
10-11
12-13
14-15
16-17
18-19
20-21
22-23
24-25
26-27
28-255
25
step
step
step
step
step
step
step
step
step
step
Static gobo wheel
23
0-8
9-17
18-26
27-35
36-44
45-53
54-62
63-71
72-80
81-91
92-103
104-115
116-127
128-139
140-151
152-163
164-175
176-187
188-199
200 - 201
202 - 222
223 - 243
244 - 249
250 - 255
26
Macro 1 (Focus=159)
Macro 2 (Focus=144)
Macro 3 (Focus=146)
Macro 4 (Focus=160)
Macro 5 (Focus=181)
Macro 6 (Focus=181)
Macro 7 (Focus=166)
Macro 8 (Focus=142)
Macro 9 (Focus=151)
Macro 10 (Focus=152)
Reserved
Open/hole (0=default)
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Shaking gobos from slow to fast
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Open/hole
Forwards gobo wheel rotation from fast to slow
Backwards gobo wheel rotation from slow to fast
Random gobo selection by audio control
(Set microphone sensitivity in menu „Personality”)
Auto random gobo selection from fast to slow
step
step
step
step
step
step
step
step
step
step
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
step
proportional
proportional
step
proportional
Rotating gobo wheel
24
0-3
4-7
Index - set indexing on channel 27/25
Open/hole (0=default)
Gobo 1
Page 8
step
step
DMX protocol
Mode/channel
1
2
DMX
Value
8-11
12-15
16-19
20-23
24-27
28-31
32-35
36-39
40-43
44-47
48-51
52-55
56-59
Function
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Rotation - set rotation on channel 27/25
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Type of
control
step
step
step
step
step
step
step
step
step
step
step
step
step
Shaking gobos from slow to fast
Index - set indexing on channel 27/25
60 - 69 Gobo 1
70 - 79 Gobo 2
80 - 89 Gobo 3
90 - 99 Gobo 4
100 - 109 Gobo 5
110 - 119 Gobo 6
120 - 129 Gobo 7
proportional
proportional
proportional
proportional
proportional
proportional
proportional
Shaking gobos from slow to fast
Rotation - set rotation on channel 27/25
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Open/hole
Forwards gobo wheel rotation from fast to slow
No rotation
Backwards gobo wheel rotation from slow to fast
Random gobo selection by audio control
(Set microphone sensitivity in menu „Personality”)
250 - 255 Auto random gobo selection from fast to slow
130 - 139
140 - 149
150 - 159
160 - 169
170 - 179
180 - 189
190 - 199
200 - 201
202 - 221
222 - 223
224 - 243
244 - 249
27
Gobo indexing - set position on channel 26/24
Gobo indexing
Gobo rotation - set position on channel 26/24
0
No rotation
1 - 127 Forwards gobo rotation from fast to slow
128
No rotation (128=default)
129 - 255 Backwards gobo rotation from slow to fast
*
proportional
proportional
proportional
proportional
proportional
proportional
step
proportional
step
proportional
step
proportional
Rot. gobo indexing and rotation
25
0 - 255
28
proportional
Rot. gobo indexing/rotation - fine
Page 9
proportional
step
proportional
step
proportional
DMX protocol
Mode/channel
1
2
DMX
Value
0-255
29
Function
Fine indexing/rotation (0=default)
Type of
control
proportional
Prism
26
0 - 19
20 - 73
74-127
Open position - hole (0=default)
Prism indexing
Prism rotation
Prism/gobo macros
step
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Macro 13
Macro 14
Macro 15
Macro 16
step
step
step
The following channels are blocked: Prism, Prism rotation, Static gobo
wheel, Rotating gobo wheel, Rot. Gobo indexing and rotation, Rot. Gobo
wheel fine rotation.
128 - 135
136 - 143
144 - 151
152 - 159
160 - 167
168 - 175
176 - 183
184 - 191
192 - 199
200 - 207
208 - 215
216 - 223
224 - 231
232 - 239
240 - 247
248 - 255
30
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
Prism indexing/rotation
27
Prism indexing - set position on channel 29/26
0 - 255 Prism 1 indexing
Prism rotation - set position on channel 29/26
0
No rotation
1 - 127 Forwards prism rotation from fast to slow
128
No rotation (128=default)
129-255 Backwards prism rotation from slow to fast
31
proportional
step
proportional
step
proportional
Frost
28
0
1-50
51-53
54-63
64-73
74-83
84-86
87-136
137-139
140-149
150-159
160-169
Open (0=default)
Light Frost
Light Frost from 0% to 100%
100% Light Frost
Pulse closing from slow to fast
Pulse opening from fast to slow
Ramping from fast to slow
Open
Medium Frost
Medium Frost from 0% to 100%
100% Medium Frost
Pulse closing from slow to fast
Pulse opening from fast to slow
Ramping from fast to slow
Page 10
step
proportional
step
proportional
proportional
proportional
step
proportional
step
proportional
proportional
proportional
DMX protocol
Mode/channel
1
2
DMX
Value
Function
170-172 Open
Combined Frost
173-222 Medium Frost from 0% to 100% (Light Frost inserted)
223-225 100% Medium Frost (Light Frost inserted)
226-235 Pulse closing from slow to fast
236-245 Pulse opening from fast to slow
246-255 Ramping from fast to slow
32
0
Open (0=default)
1 - 179 From max. diameter to min. diameter
180 - 191 Closed
Pulse effects with Iris blackout
192 -219 Pulse opening from slow to fast
220 - 247 Pulse closing from fast to slow
248 - 249 Random pulse opening (fast)
250 - 251 Random pulse opening (slow)
252 - 253 Random pulse closing (fast)
254 - 255 Random pulse closing (slow)
*
34
30
35
*
38
32
Fine iris movement (0=default)
Zoom from max. to min. beam angle (128=default)
0-255
Fine zooming (0=default)
40
41
42
43
44
33
34
35
36
37
38
proportional
proportional
step
proportional
step
proportional
proportional
step
step
step
step
proportional
proportional
0 - 255
Continuous adjustment from far to near (128=default)
proportional
Focus
proportional
Focus - fine
0- 255
39
proportional
Zoom - fine
31
*
step
Zoom
0 - 255
37
proportional
Iris - fine
0 - 255
36
step
Iris
29
33
Type of
control
Fine focusing (0=default)
Framing shutters module rotation
0-127 Rotation from right (0°) to 60°
128
Centre (128=default)
129-255 Rotation from 60° to left (120°)
Framing shutter 1- movement
0-255 Movement from Outward to Inward (0=default)
Framing shutter 1- swivelling
0-127 Swivelling from -30 degrees towards 0 degrees
128
0 degrees (128=default)
129-255 Swivelling from 0 degrees to +30 degrees
Framing shutter 2- movement
0-255 Movement from Outward to Inward (0=default)
Framing shutter 2- swivelling
0-127 Swivelling from -30 degrees towards 0 degrees
128
0 degrees (128=default)
129-255 Swivelling from 0 degrees to +30 degrees
Framing shutter 3 movement
0-255 Movement from Outward to Inward (0=default)
Framing shutter 3- swivelling
0-127 Swivelling from -30 degrees towards 0 degrees
Page 11
proportional
proportional
step
proportional
proportional
proportional
step
proportional
proportional
proportional
step
proportional
proportional
proportional
DMX protocol
Mode/channel
1
2
45
46
47
39
40
DMX
Value
128
0 degrees (128=default)
129-255 Swivelling from 0 degrees to +30 degrees
Framing shutter 4 movement
0-255 Movement from Outward to Inward (0=default)
Framing shutter 4- swivelling
0-127 Swivelling from -30 degrees towards 0 degrees
128
0 degrees (128=default)
129-255 Swivelling from 0 degrees to +30 degrees
0 - 31
32 - 63
64 - 95
96 - 127
128 - 143
144 - 159
160 - 191
192 - 223
224 - 255
42
49
*
Type of
control
step
proportional
proportional
proportional
step
proportional
Shutter/ strobe
41
48
Function
Shutter closed
Shutter open (32=default)
Strobe-effect from slow to fast
Shutter open
Opening pulse in sequences from slow to fast
Closing pulse in sequences from fast to slow
Shutter open
Random strobe-effect from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
Dimmer intensity
0 - 255
Dimmer intensity from 0% to 100% (0=default)
proportional
Dimmer intensity - fine
0 - 255
Fine dimming (0=default)
proportional
Copyright © 2019 Robe Lighting s.r.o. - All rights reserved
All Specifications subject to change without notice
Page 12
Robin Esprite - Colours on Virtual Colour Wheel
Col.
Col.
Magenta
Colour name
Wheel 1 Wheel 2 Cyan DMX
DMX
DMX
DMX
0
0
0
134
Filter 4 (Medium Bastard Amber)
0
0
0
45
Filter 10 (Medium Yellow)
154
0
0
210
Filter 19 (Fire)
130
0
0
45
Filter 26 (Bright Red)
0
0
10
205
Filter 58 (Lavender)
0
154
165
120
Filter 68 (Sky Blue)
144
0
0
0
Filter 71 (Tokyo Blue)
0
154
165
135
Filter 79 (Just Blue)
0
142
0
90
Filter 88 (Lime Green)
0
142
201
0
Filter 90 (Dark Yellow Green)
0
0
0
0
Filter 100 (Spring Yellow)
0
0
0
75
Filter 101 (Yellow)
0
0
0
60
Filter 102 (Light Amber)
0
0
0
0
Filter 103 (Straw)
0
0
0
150
Filter 104 (Deep Amber)
0
0
0
195
Filter 105 (Orange)
154
0
0
240
Filter 106 (Primary Red)
0
0
0
182
Filter 111 (Dark Pink)
0
0
246
0
Filter 115 (Peacock Blue)
0
0
239
0
Filter 116 (Medium Blue-Green)
0
0
180
90
Filter 117 (Steel Blue)
0
0
225
0
Filter 118 (Light Blue)
0
0
255
120
Filter 119 (Dark Blue)
0
154
255
30
Filter 120 (Deep Blue)
0
142
135
0
Filter 121 (Filter Green)
0
0
52
235
Filter 128 (Bright Pink)
0
0
210
15
Filter 131 (Marine Blue)
0
0
240
0
Filter 132 (Medium Blue)
0
0
49
201
Filter 134 (Golden Amber)
0
0
49
223
Filter 135 (Deep Golden Amber)
0
0
64
198
Filter 136 (Pale Lavender)
0
0
34
159
Filter 137 (Special Lavender)
0
0
120
81
Filter 138 (Pale Green)
166
0
0
0
Filter 139 (Primary Green)
0
0
240
0
Filter 141 (Bright Blue)
0
0
0
182
Filter 147 (Apricot)
0
0
0
225
Filter 148 (Bright Rose)
0
0
57
190
Filter 152 (Pale Gold)
0
0
57
185
Filter 154 (Pale Rose)
0
0
59
224
Filter 157 (Pink)
0
0
0
220
Filter 158 (Deep Orange)
0
0
0
165
Filter 162 (Bastard Amber)
154
0
0
240
Filter 164 (Flame Red)
0
0
210
0
Filter 165 (Daylight Blue)
0
0
87
202
Filter 169 (Lilac Tint)
1
Yellow
DMX
CTO
DMX
150
210
0
255
93
0
0
0
0
147
210
210
165
150
225
240
0
164
185
193
165
165
0
0
210
194
135
15
237
254
131
112
201
0
45
221
217
204
189
223
255
195
30
0
169
225
255
0
90
101
0
0
0
225
0
165
255
240
240
210
150
15
255
0
0
15
30
0
105
0
113
30
105
28
40
0
0
50
240
195
0
0
0
67
0
0
0
195
75
0
Colour name
Filter 170 (Deep Lavender)
Filter 172 (Lagoon Blue)
Filter 179 (Chrome Orange)
Filter 180 (Dark Lavender)
Filter 181 (Congo Blue)
Filter 197 (Alice Blue)
Filter 201 (Full C.T. Blue)
Filter 202 (Half C.T. Blue)
Filter 203 (Quarter C.T. Blue)
Filter 204 (Full C.T. Orange)
Filter 205 (Half C.T. Orange)
Filter 206 (Quarter C.T. Orange)
Filter 247 (Filter Minus Green)
Filter 248 (Half Minus Green)
Filter 281 (Three Quarter C.T. Blue)
Filter 285 (Three Quarter C.T. Orange)
Filter 352 (Glacier Blue)
Filter 353 (Lighter Blue)
Filter 715 (Cabana Blue)
Filter 778 (Millennium Gold)
Filter 793 (Vanity Fair)
Col.
Wheel 1
DMX
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Col.
Magenta
Wheel 2 Cyan DMX
DMX
DMX
0
98
200
0
225
30
0
57
190
0
175
185
0
195
225
154
225
0
0
180
0
0
168
0
0
135
45
0
0
195
0
90
180
0
0
165
0
0
184
0
48
134
0
180
0
0
0
173
0
210
0
0
220
0
154
255
0
0
0
215
0
15
225
2
Yellow
DMX
CTO
DMX
133
135
240
0
0
0
105
37
120
240
210
163
131
110
105
234
105
144
0
255
0
0
15
0
0
15
60
60
118
0
30
0
30
20
24
120
90
60
0
105
0
255
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement