Extech Instruments HDV610 HD VideoScope Kit User's Manual

Extech Instruments HDV610 HD VideoScope Kit User's Manual
User Manual
High Definition VideoScope
Model HDV600
Additional User Manual Translations available at www.extech.com
Introduction
Congratulations on your purchase of this Extech HDV600 series Video Borescope. This instrument
is designed for use as a remote inspection device. It can be used to peer into tight spots, record and
playback real-time video and images. Typical applications include HVAC inspection, automotive
inspection, cable routing, and automotive/boat/aircraft inspection. The monitor is designed with dual
left or right handed controls for maximum flexibility and is available with a full line of accessories.
This meter is shipped fully tested and, with proper use, will provide years of reliable service.
Models and Descriptions:
HDV600
VideoScope (Monitor only)
HDV610
VideoScope w/1m flexible cable, 5.5mm diameter
HDV620
VideoScope w/1m semi-rigid cable, 5.8mm diameter
HDV640
VideoScope w/1m Articulating semi-rigid cable, 6mm diameter
HDV640W
VideoScope w/1m Wireless Articulating semi-rigid cable, 6mm diameter
Note: Additional probe lengths and configurations are available. A list is available at the end of this
guide.
Cautions
The IP67 waterproof rating applies to the monitor when the bottom panel access cover is fully in
place.
For the Articulating Probe, do not operate the articulation knob with the probe
in a coiled configuration. This will damage the articulation controls!
2
HDV600-en-GB_V3.0 1/18
Description
Monitor
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Probe connector
Camera button
Video button
Rotate image button
Display
Zoom buttons
Light intensity buttons
Power Button
Scroll buttons
Selection buttons
USB connector
Microphone
SD card slot
Video output jack
Reset button
AC adaptor connector
Articulating Probe
1. Articulation knob
2. Articulation tension knob
3. Articulating camera
4. Light intensity buttons
5. Power button
6. AC Adaptor and extension cable sockets
7. Carrying strap
Wireless Transmitter
1.
Probe Connector
2.
Light Intensity buttons
3.
Power button
4.
AC Adaptor and extension cable sockets
5.
Carrying strap
Probe accessories
1.
Anti-snag tip
2.
Magnet
3.
45° Mirror
Probe
1.
2.
3.
Camera
Shaft
Monitor connector
3
HDV600-en-GB_V3.0 1/18
Setup
Battery Charging and Status Indication:
Note: A fully charged battery will allow approximately 5 hours of continuous use.
1.
Turn the meter off and then connect the AC adaptor to charge the meter.
2.
After several hours, turn the meter on. The battery icon will indicate either:
A: Fully charged
B: Charge in progress
3.
If the battery is charged, remove the AC adaptor and observe that the fully charged 4 bar
icon
appears.
4.
If the battery icon indicates less than 4 bars, turn the meter off and continue charging.
5.
Always wait for a full fully charged indication to maximize operation time and to maintain
battery health.
Note: The battery will not properly charge if the meter is on during the charging cycle.
Startup
1.
Insert the SD card into the bottom SD slot
2.
Press the Power button to turn the monitor on. The battery icon will briefly appear indicating
the battery condition.
3.
Press OK to open the setup MENU
4.
Press the ▲ or ▼ button to scroll through the
MENU selections.
5.
Press OK to open the highlighted selection.
6.
Press the ▲ or ▼ button to scroll through the
items in an open menu item.
7.
Press the ▲ or ▼ buttons to increase or
decrease the selected value.
8.
After there has been a change, press the OK button to save the change or the ESC button to
exit without the change.
Note: After 10 seconds of inactivity, the Setup menu will exit without storing changes.
MENU Description:
DELETE ALL:
Erase all stored pictures and videos
DATE/TIME SETUP:
Set the date (year/month/day), time (hour:minute:second) and display
on/off
LANGUAGE:
Set the menu display to any one of 21 languages.
VIDEO FORMAT:
Set the video output to NTSC or PAL format.
AUTO POWER OFF:
Set the APO to 5, 10, 15, 30 minutes or DISABLE.
INPUT SOURCE:
Set Direct or Wireless.
4
HDV600-en-GB_V3.0 1/18
Operation
1.
Connect the probe to the monitor.
2.
Press the Power button to turn the monitor on.
3.
Maneuvere the probe into position to view the area to be examined. The probe can be
bent into the shape of the area to be examined. Optimum focus distance is 2 to 6cm (0.79
to 2.3”)
4.
Optimum focus distance is probe dependent, but the typical range is 2 to 6cm
Zoom
Press the
or
zoom buttons to increase or decrease the display resolution from 1X to 2X.
Light Intensity
Press and release the
or
buttons to increase or decrease the camera LED light
intensity
Note: the camera LEDs become warm when set to maximum intensity
Taking a Picture
Press the
button to take and store a picture into memory. The
display when a picture is taken.
icon will appear on the
Recording a Video
Press the
button to start recording a video. The
icons will appear on the display
when a video is being recorded. Press the
button to stop the recording. Audio will be
recorded on the video via the microphone on the bottom of the monitor.
Note: The bottom access cover must be removed for audio recording.
The IP67 waterproof rating applies to the monitor when the bottom panel access cover is fully in
place.
Display Rotation
Press the
button to rotate the display 90 degrees.
Installing probe accessories
Three accessories (mirror, anti-snag tip and magnet) are supplied with each probe.
Attach the accessory by unscrewing the probe ring and screwing on the attachment.
5
HDV600-en-GB_V3.0 1/18
Articulating probe
The articulating probe, with adjustable tip angle, is used for improved
viewing angles and optimum inspection when the probe is inserted into the
inspection location. The articulating probe is available in a direct (wired) or
wireless version.
Wireless version
Note: The battery must be fully charged for wireless operation. A weak battery may result in meter
shut down.
1.
Connect the AC adaptor to the transmitter and charge
the battery.
2.
Press and hold the Power button for 4 seconds to turn
the monitor on, then select “WIRELESS” under the
INPUT SOURCE selection in the MENU screen.
3.
Press and hold the Power button for 4 seconds to turn
the transmitter on. The camera video will be transmitted
to the monitor display.
4.
Insert the probe into the area to be inspected.
5.
Turn the probe outer knob to adjust the camera tip to
the viewing angle needed.
6.
Turn the upper knob to increase or decrease the outer
knob tension
Direct version
1.
Connect the probe to the monitor using the supplied
patch cable.
2.
Press and hold the Power buttons for 4 seconds to
turn the probe and the monitor on
3.
Insert the probe into the area to be inspected.
4.
Turn the probe outer knob to adjust the camera tip to
the viewing angle needed.
5.
Turn the upper knob to increase or decrease the
outer knob tension
6.
In this mode, light intensity is controlled by the
buttons on the monitor, not by the buttons on the
transmitter.
6
HDV600-en-GB_V3.0 1/18
Wireless transmitter
The wireless transmitter is intended for use in areas that are difficult to access or in situations
when is hard to maneuver the probe with the display attached. The probe can also be connected
directly to the monitor using the patch cord.
Note: The battery must be fully charged for wireless operation. A weak battery may result in meter
shut down.
Wireless Mode
1.
Connect the AC adaptor to the transmitter and charge the
battery.
2.
Attach the probe to the transmitter.
3.
Press and hold the Power button for 4 seconds to turn the
monitor on, then select “WIRELESS” under the INPUT
SOURCE selection in the MENU screen.
4.
Press and hold the Power button for 4 seconds to turn the
transmitter on. The camera video will be transmitter to the
monitor display.
Direct Mode
1.
Connect the AC adaptor to the transmitter and charge the
battery.
2.
Attach the probe to the transmitter.
3.
Connect the patch cord between the transmitter and the monitor probe input connector
4.
Press and hold the Power button for 4 seconds to turn the
transmitter on.
5.
Press and hold the Power button for 4 seconds to turn the
monitor on, then select “DIRECT” under the INPUT
SOURCE selection in the MENU screen.
6.
In the direct mode, light intensity is controled by the
buttons on the monitor, not by the buttons on the
transmitter.
7
HDV600-en-GB_V3.0 1/18
Viewing a Stored Photo or Video in the Display
1.
Press the ▲ button to access the pictures or videos in memory. Each button press will
step through the files with the file number appearing on the screen (i.e. IMG00005)
2.
Pictures will appear with the
3.
Videos will appear with the
4.
To play a video, select a video file and press the
during playback. Press the
appear.
photo icon on the display.
film icon on the display.
button. The
play icon will appear
button again to pause playback. The
pause icon will
Viewing an Image or Video on a PC
There are two methods to transfer stored files to a pc.
1. Remove the SD card from the monitor and insert it into the SD reader in the pc.
2. Connect the monitor to the pc with a USB cable.
Images are saved in *.JPG format and videos saved in *.AVI format
Deleting stored Images or Videos
1.
2.
3.
4.
Press the ▲ button to access the pictures or videos in memory.
When the file to be deleted appears, press the OK button and the DELETE YES/NO box
will appear.
Press the ▲ button to highlight YES and then press the OK button to delete the file.
Press the ESC button to exit at any time without deleteing the file.
Video Output
1.
2.
3.
Turn the monitor on and select “PAL” or “NTSC”, to match the video monitor to be used,
under the VIDEO OUTPUT selection in the MENU screen and press OK.
Insert the video cable into the VIDEO OUT socket on the bottom of the monitor. Connect the
other end of the cable into the VIDEO IN jack of a TV or other monitor.
The unit will output a high quality video image.
Video Profiles Menu
The HDV600 monitor has 2 factory default profiles (Default1 and Default2) and one User profile
for Brightness, Contrast, Hue, and Saturation camera settings. To access the Factory Default
menu, follow this procedure.
1. Press the OK button and using the arrow button navigate to Video Format. Press OK
2. Highlight NTSC and press the Still camera button.
3. Use the down arrow to select Default1 or Default2. The user can also adjust each video
parameter manually for the best picture.
4. Press the ESC button 2 times to return to the image view mode.
8
HDV600-en-GB_V3.0 1/18
Reset button
If the monitor becomes unresponsive due to an EMI field or other magnetic event, use a paper
clip or other pointed object to press the RESET button located on the bottom panel
Rear stand
The rear stand can be set to three positions. Lower (stored), middle position for bench viewing
and upper position for hanging.
FCC Information
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause
undesired operation.
Battery Replacement
The charging circuit is designed only for the lithium battery included with the meter. The meter
should be returned to one of our repair facilities for replacement. Non-approved lithium battery could
cause damage to the instrument or hazard to the users.
Safety: Please dispose of batteries responsibly; never dispose of batteries in a fire, batteries may
explode or leak. If the meter is not to be used for 60 days or more, remove the battery and store
separately.
Never dispose of used batteries or rechargeable batteries in household waste.
As consumers, users are legally required to take used batteries to appropriate collection
sites, the retail store where the batteries were purchased, or wherever batteries are sold.
Disposal: Do not dispose of this instrument in household waste. The user is obligated to take end-oflife devices to a designated collection point for the disposal of electrical and electronic equipment.
9
HDV600-en-GB_V3.0 1/18
Specifications
Monitor
14.5cm (5.7”) Viewable 13.5cm (5.3”)
Active matrix, 640x480 pixels
Interface
Mini USB 1.1 and AV out
Recording medium
SD Card
Compression format
MPGE4
Still image format
JPEG (640x480)
Video Recording Format
AVI (640x480)
Video output Format
NTSC and PAL
Receiver Frequency
2.4GHz
Receiver Sensitivity
-87dBm (SNR = 42dB, Fmod = 15kHz)
Video System
NTSC / PAL
Data
Video / Audio
Audio type
Stereo
Tripod mount
On rear, Accepts standard tripod screw
Battery
3.7V rechargeable Li-Polymer
Power adaptor
100 to 240V input / 5VDC output
Operating/Storage Temperature -10 to 60°C(14 to 140°F) / -40 to 80°C(-40 to 176°F)
Operating Humidity (Max.)
80%
Ingress protection
IP67
Dimensions (W x D x H)
24.1 x 17.8 x 7.0cm (9.5’x7”x2.75”)
Weight
1474g (3.25lb)
LCD Screen
Transmitter
Frequency
Data
Video System
Battery
Power adaptor
Unobstructed Effective Range
Operating/Storage Temperature
Dimensions (W D H)
Weight (approx)
2.4GHz
Video / Audio
NTSC / PAL
3.7V rechargeable Li-Polymer
100 to 240V input / 9VDC output
10m
-10 to 60°C(14 to 140°F) / -40 to 80°C(-40 to 176°F)
19 x 7 x 6.35cm (7.5’ x 2.75 x 2.5”)
431g (0.95lb)
10
HDV600-en-GB_V3.0 1/18
Camera
Imaging Sensor
Video Format
Brightness Control
Lamp Type
Interface
Ingress protection
Operating Temperature
CMOS
NTSC
Manual
LED
Composite Video
IP67
-20°C to 70°C (-4°F to 158°F)
Probes and Cameras
Articulation
Accessories
Part Number
HDV-TX1
HDV-WTX1
HDV-TX2
HDV-WTX2
HDV-4CAM-1FM
HDV-5CAM-1FM
HDV-5CAM-3F
HDV-5CAM-3FM
HDV-5CAM-10F
HDV-5CAM-1RM
HDV-5CAM-3R
HDV-5CAM-3RM
HDV-25CAM-10G
HDV-25CAM-30G
240°±20° manual tip articulation
Mirror, magnet and anti-snag Ball (excluding 25mm diameter
cables)
Description
Articulating Semi-Rigid
Wireless Articulating Semi-Rigid
Articulating Semi-Rigid Cable
Wireless Articulating Semi-Rigid
Macro lens Flexible
Macro lens Flexible
Long depth of field Flexible
Macro lens Flexible
Long depth of field Flexible
Macro lens Semi-Rigid
Long depth of field Semi-Rigid
Macro lens Semi-Rigid
Fiberglass
Fiberglass
OD
6mm
6mm
6mm
6mm
4mm
5.5mm
5.5mm
5.5mm
5.5mm
5.5mm
5.5mm
5.5mm
25mm
25mm
Length
1m
1m
2m
2m
1m
1m
3m
3m
10m
1m
3m
3m
10m
30m
Camera
640x480
640x480
640x480
640x480
320x240
640x480
640x480
640x480
640x480
640x480
640x480
640x480
640x480
640x480
Focus Distance
2 to 6cm
2 to 6cm
2 to 6cm
2 to 6cm
2 to 6cm
2 to 6cm
6 cm to ∞
2 to 6cm
6 cm to ∞
2 to 6cm
6 cm to ∞
2 to 6cm
6 cm to ∞
6 cm to ∞
Copyright © 2012-2018 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part in any form
ISO-9001 Certified
www.extech.com
11
HDV600-en-GB_V3.0 1/18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement