Code CR1100 User Manual

Code CR1100 User Manual
USER MANUAL
CR1100
MANUAL VERSION 01
RELEASE DATE: JANUARY 2019
www.codecorp.com
Configuration Guide
Statement of Agency Compliance
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Industrie Canada (IC)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Code Reader™ CR1100 User Manual
Copyright © 2019 Code Corporation.
All Rights Reserved.
The software described in this manual may only be used in accordance with the terms of its license agreement.
No part of this publication may be reproduced in any form or by any means without written permission from Code Corporation. This includes
electronic or mechanical means such as photocopying or recording in information storage and retrieval systems.
NO WARRANTY. This technical documentation is provided AS-IS. Further, the documentation does not represent a commitment on the part
of Code Corporation. Code Corporation does not warrant that it is accurate, complete or error free. Any use of the technical documentation
is at the risk of the user. Code Corporation reserves the right to make changes in specifications and other information contained in this
document without prior notice, and the reader should in all cases consult Code Corporation to determine whether any such changes
have been made. Code Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or
consequential damages resulting from the furnishing, performance, or use of this material. Code Corporation does not assume any product
liability arising out of or in connection with the application or use of any product or application described herein.
NO LICENSE. No license is granted, either by implication, estoppel, or otherwise under any intellectual property rights of Code Corporation.
Any use of hardware, software and/or technology of Code Corporation is governed by its own agreement.
The following are trademarks or registered trademarks of Code Corporation:
CodeXML®, Maker, QuickMaker, CodeXML® Maker, CodeXML® Maker Pro, CodeXML® Router, CodeXML® Client SDK, CodeXML® Filter,
HyperPage, CodeTrack, GoCard, GoWeb, ShortCode, GoCode®, Code Router, QuickConnect Codes, Rule Runner®, Cortex®, CortexRM,
CortexMobile, Code, Code Reader, CortexAG, CortexStudio, CortexTools, Affinity®, and CortexDecoder.
All other product names mentioned in this manual may be trademarks of their respective companies and are hereby acknowledged.
The software and/or products of Code Corporation include inventions that are patented or that are the subject of patents pending. U.S.
Patents: 6997387, 6957769, 7428981, 6619547, 6736320, 7392933, 7014113, 7240831, 7353999, 7519239, 7204417,
6942152, 7070091, 7097099, 7621453, 8001550, 8011584
The Code Reader software uses the Mozilla SpiderMonkey JavaScript engine, which is distributed under the terms of the Mozilla Public
License Version 1.1.
The Code Reader software is based in part on the work of the Independent JPEG Group.
Code Corporation, 12393 S. Gateway Park Place, Ste. 600, Draper, Utah 84020
www.codecorp.com
D007007_08
UserUser
Manual
D032078
_01CR1000
CR1100
Manual
2
Table of Contents
1.0 - Included Items if Ordered............................................................................. 4
2.0 - Attaching and Detaching a Cable................................................................... 5
3.0 - Set Up........................................................................................................ 5
4.0 - Using a CR1100 Out of a Stand.................................................................... 6
5.0 - Using a CR1100 In a Stand ......................................................................... 6
6.0 - Reading Ranges........................................................................................... 6
7.0 - Reader Feedback......................................................................................... 7
8.0 - Symbologies Defaulted On............................................................................ 7
9.0 - Symbologies Defaulted Off............................................................................ 7
10.0 - Reader ID & Firmware Version..................................................................... 8
11.0 - CR1100 Hole Mounting Pattern.................................................................. 8
12.0 - CR1100 Overall Dimensions....................................................................... 9
13.0 - USB Cable Example with Pinouts................................................................ 9
14.0 - RS232 Cable Example with Pinouts............................................................. 9
15.0 - Reader Pinouts........................................................................................ 10
16.0 - CR1100 Maintenance.............................................................................. 10
17.0 - Warranty................................................................................................. 11
D007007_08
CR1000 User
Manual
D032078
_01 CR1100
User
Manual
3
1.0 - Included Items if Ordered
CR1100
USB 2.0 Cable
D007007_08
User
Manual
D032078
_01 CR1000
CR1100
User
Manual
RS232 Cable
5VDC
Power Supply
4
2.0 - Attaching and Detaching a Cable
3.0 - Set Up
USB
RS232
Plug in
1
Wait 2 seconds
2
2 Sec.
LED will flash
3
4
Reader will beep
2x
D007007_08
User
Manual
D032078
_01 CR1000
CR1100
User
Manual
5
4.0 - U
sing a CR1100
Out of a Stand
5.0 - Using a CR1100
In a Stand
10 cm
10 cm
6.0 - Typical Reading Ranges
Test Barcode
Min Inches (mm)
Max Inches (mm)
3 mil Code 39
3.3” (84 mm)
4.3” (109 mm)
7.5 mil Code 39
1.9” (47 mm)
7.0” (177 mm)
10.5 mil GS1 DataBar
0.6” (16 mm)
7.7” (196 mm)
13 mil UPC
1.3” (33 mm)
11.3” (286 mm)
5 mil DM
1.9” (48 mm)
4.8” (121 mm)
6.3 mil DM
1.4” (35 mm)
5.6” (142 mm)
10 mil DM
0.6” (14 mm)
7.2” (182 mm)
20.8 mil DM
1.0” (25 mm)
12.6” (319 mm)
Note: Working ranges are a combination of both the wide and high density fields. All samples were high quality barcodes and were read along a
physical center line at a 10° angle. Measured from the front of the reader with default settings. Testing conditions may impact reading ranges.
D007007_08
UserUser
Manual
D032078
_01CR1000
CR1100
Manual
6
7.0 - Reader Feedback
Scenario
Top LED Light
Sound
CR1100 Successfully Powers Up
Green LED Flashes
1 Beep
CR1100 Successfully Enumerates with Host (via cable)
Once Enumerated, the Green
LED turns Off
1 Beep
Attempting to Decode
Green LED Light is Off
None
Successful Decode and Data Transfer
Green LED Flashes
1 Beep
Configuration Code Successfully Decoded and Processed
Green LED Flashes
2 Beeps
Configuration Code successfully decoded but wasn’t
successfully processed
Green LED Flashes
4 Beeps
Downloading File/Firmware
Amber LED Flashes
None
Installing File/Firmware
Red LED is On
3-4 Beeps*
*Depending on comm port configuration
8.0 - Symbologies Defaulted On
The following are symbologies that have a default of ON.
To turn symbologies on or off, scan the symbology barcodes
located in the CR1100 Configuration Guide located on our
website at www.codecorp.com/files.php.
Aztec
Codabar
Code 39
Code 93
Code 128
Data Matrix
Data Matrix Rectangle
All GS1 DataBar
Interleaved 2 of 5
PDF417
QR Code
UPC/EAN/JAN
D032078
_01CR1000
CR1100
User
Manual
D007007_08
User
Manual
9.0 - Symbologies Defaulted Off
Code barcode readers can read a number of barcode
symbologies that are not enabled by default. To turn
symbologies on or off, scan the symbology barcodes located in
the CR1100 Configuration Guide located on our website at
www.codecorp.com/files.php.
Codablock F
Code 11
Code 32
Code 49
Composite
Grid Matrix
Han Xin Code
Hong Kong 2 of 5
IATA 2 of 5
Matrix 2 of 5
Maxicode
Micro PDF417
MSI Plessey
NEC 2 of 5
Pharmacode
Plessey
Postal Codes
Standard 2 of 5
Telepen
Trioptic
7
10.0 - Reader ID and Firmware Version
To find out the Reader ID and Firmware version, open a text editor program
(i.e., Notepad, Microsoft Word, etc.) and read the Reader ID and Firmware
configuration barcode.
Reader ID and Firmware
You will see a text string indicating your firmware version and CR1100 ID number.
example: <RD><RR MD=”CR1100” /></RD><RD><RR SN=”1060000003” /></RD><RD><FW VS=”1.1.4 ” /></RD><RD><LC GL=”” /></RD>
Model Number
Serial Number
Firmware
Version
Number
License Part
Number (if there
is any)
<RD><RR MD=”CR1100” /></RD><RD><RR SN=”1060000003” /></RD><RD><FW VS=”1.1.4” /></RD><RD><LC GL=”” /></RD>
Note:Code will periodically release new firmware for CR1100, which requires CortexTools2 to update. There are also a number of drivers
(VCOM, OPOS, JPOS) available on the website. For access to the latest drivers, firmware, and support software, please visit our website at
www.codecorp.com/files.php
11.0 - CR1100 Hole Mounting Pattern
34.1 mm (1.34”)
15.5 mm (0.6”)
10.4 mm (0.41”)
NOTE 1:
Locating holes are 2 mm (0.08”)
diameter, hole depth is 1.5 mm
(0.06”)
NOTE 2:
Mounting inserts are M3 x 0.5
internal thread, 3.8 mm (0.15”)
length.
30.2 mm (1.19”)
27.0 mm (1.06”)
31.1 mm (1.23”)
D007007_08
UserUser
Manual
D032078
_01CR1000
CR1100
Manual
8
12.0 - CR1100 Overall Dimensions
67.5 mm
(2.7”)
29.7 mm
(1.2”)
52.5 mm
(2.1”)
13.0 - USB Cable Example with Pinouts
NOTES:
1. Maximum Voltage Tolerance = 5V +/- 10%.
2. C
aution: Exceeding the maximum voltage will void
manufacturer warranty.
CONNECTOR A
NAME
CONNECTOR B
1
VIN
1
2
D-
2
3
D+
3
4
GND
10
SHELL
SHIELD
N/C
CONNECTOR A
CONNECTOR B
14.0 - RS232 Cable Example with Pinouts
NOTES:
1. Maximum Voltage Tolerance = 5V +/- 10%.
2. C
aution: Exceeding the maximum voltage will void
manufacturer warranty.
D007007_08
User
Manual
D032078
_01CR1000
CR1100
User
Manual
CONNECTOR A
NAME
CONNECTOR B
CONNECTOR C
1
VIN
1
TIP
4
TX
2
5
RTS
8
6
RX
3
7
7
CTS
10
GND
5
N/C
SHIELD
SHELL
RING
9
15.0 - Reader Pinouts
The connector on the CR1100 is an RJ-50
(10P-10C). The pinouts are as follows:
Pin 1
+VIN (5v)
Pin 2
USB_D-
Pin 3
USB_D+
Pin 4
RS232 TX (output from reader)
Pin 5
RS232 RTS (output from reader)
Pin 6
RS232 RX (input to reader)
Pin 7
RS232 CTS (input to reader)
Pin 8
External Trigger (active low input to reader)
Pin 9
N/C
Pin 10
Ground
16.0 - CR1100 Maintenance
The CR1100 device needs only a minimum of maintenance to operate. A few tips are given below for maintenance suggestions.
Cleaning the CR1100 Window
CR1100 window should be clean to allow the best performance of the device. The window is the clear plastic piece inside the head of
the reader. Do not touch the window. Your CR1100 uses CMOS technology that is much like a digital camera. A dirty window may stop
the CR1100 from reading barcodes.
If the window becomes dirty, clean it with a soft, non-abrasive cloth or a facial tissue (no lotions or additives) that has been moistened
with water. A mild detergent may be used to clean the window, but the window should be wiped with a water moistened cloth or tissue
after using the detergent.
Technical Support and Returns
For returns or technical support call Code Technical Support at (801) 495-2200. For all returns Code will issue an RMA number which
must be placed on the packing slip when the reader is returned. Visit www.codecorp.com/codesupport.php for more information.
D007007_08
UserUser
Manual
D032078
_01CR1000
CR1100
Manual
10
17.0 - Warranty
The CR1100 carries a standard two year limited warranty as described herein. Extended warranty periods may be available with a CodeOne Service
Plan. Stand and Cables have a 30 day warranty period.
Limited Warranty. Code warrants each Code product against defects in materials and workmanship under normal use for the Warranty Coverage Term
applicable to the product as described at www.codecorp.com/legal/warranty/term.php. If a hardware defect arises and a valid warranty claim is
received by Code during the Warranty Coverage Term, Code will either: i) repair a hardware defect at no charge, using new parts or parts equivalent
to new in performance and reliability; ii) replace the Code product with a product that is new or refurbished product with equivalent functionality
and performance, which may include replacing a product that is no longer available with a newer model product; or ii) in the case of failure with any
software, including embedded software included in any Code product, provide a patch, update, or other work around. All replaced products become the
property of Code. All warranty claims must be made using Code’s RMA process.
Exclusions. This warranty does not apply to: i) cosmetic damage, including but not limited to scratches, dents, and broken plastic; ii) damage resulting
from use with non-Code products or peripherals, including batteries, power supplies, cables, and docking station/cradles; iii) damage resulting from
accident, abuse, misuse, flood, fire or other external causes, including damage caused by unusual physical or electrical stress, immersion in fluids or
exposure to cleaning products not approved by Code, puncture, crushing, and incorrect voltage or polarity; iv) damage resulting from services performed
by anyone other than a Code authorized repair facility; v) any product that has been modified or altered; vi) any product on which the Code serial
number has been removed or defaced. If a Code Product is returned under a warranty claim and Code determines, in Code’s sole discretion, that the
warranty remedies do not apply, Code will contact Customer to arrange either: i) repair or replace the Product; or ii) return the Product to Customer, in
each case at Customer’s expense.
Non Warranty Repairs. Code warrants its repair/replacement services for ninety (90) days from the date of shipment of the repaired/replacement product
to the Customer. This warranty applies to repairs and replacements for: i) damage excluded from the limited warranty described above; and ii) Code
Products on which the limited warranty described above has expired (or will expire within such ninety (90) day warranty period). For repaired product
this warranty covers only the parts that were replaced during the repair and the labor associated with such parts.
No Extension of Term of Coverage. Product that is repaired or replaced, or for which a software patch, update, or other work around is provided, assumes
the remaining warranty of the original Code Product and does not extend the duration of the original warranty period.
Software and Data. Code is not responsible for backing up or restoring any of software, data, or configuration settings, or reinstalling any of the foregoing
on products repaired or replaced under this limited warranty.
Shipping and Turn Around Time. The estimated RMA turn-around time from receipt at Code’s facility to shipment of the repaired or replaced product
to Customer is ten (10) business days. An expedited turn-around time may apply to products covered under certain CodeOne Service Plans. Customer
is responsible for shipping and insurance charges for shipping Code Product to Code’s designated RMA facility and repaired or replaced product is
returned with shipping and insurance paid by Code. Customer is responsible for all applicable taxes, duties, and similar charges.
Transfer. If a customer sells a covered Code Product during the Warranty Coverage Term, then that coverage may be transferred to the new owner by
written notification from the original owner to Code Corporation at:
CodeOne Service Center
12393 South Gateway Park Place, Suite 600
Draper, UT 84020
Limitation on Liability. Code’s performance as described herein shall be Code’s entire liability, and the Customer’s sole remedy, resulting from any
defective Code product. Any claim that Code has failed to perform its warranty obligations as described herein must be made within six (6) months of
the alleged failure. Code’s maximum liability related to its performance, or failure to perform, as described herein shall be limited to the amount paid
by Customer for the Code product that is subject to the claim. In no event will either party be liable for any lost profits, lost savings, incidental damage,
or other economic consequential damages. This is true even if the other party is advised of the possibility of such damages.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE LIMITED WARRANTIES DESCRIBE HEREIN REPRESENT THE ONLY
WARRANTIES CODE MAKES WITH RESPECT TO ANY PRODUCT. CODE DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESSED OR
IMPLIED, ORAL OR WRITTEN, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT.
THE REMEDIES DESCRIBED HEREIN REPRESENT CUSTOMER’S EXCLUSIVE REMEDY, AND CODE’S ENTIRE RESPONSIBILITY, RESULTING FROM
ANY DEFECTIVE CODE PRODUCT.
CODE SHALL NOT BE LIABLE TO CUSTOMER (OR TO ANY PERSON OR ENTITY CLAIMING THROUGH CUSTOMER) FOR LOST PROFITS, LOSS OF
DATA, DAMAGE TO ANY EQUIPMENT WITH WHICH THE CODE PRODUCT INTERFACES (INCLUDING ANY MOBILE TELEPHONE, PDA, OR OTHER
COMPUTING DEVICES), OR FOR ANY SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENTIAL OR EXEMPLARY DAMAGES ARISING OUT OF OR IN
ANY MANNER CONNECTED WITH THE PRODUCT, REGARDLESS OF THE FORM OF ACTION AND WHETHER OR NOT CODE HAS BEEN INFORMED
OF, OR OTHERWISE MIGHT HAVE ANTICIPATED, THE POSSIBILITY OF SUCH DAMAGES.
D007007_08
CR1000
User Manual
D032078
_01
CR1100
User Manual
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement