Fujitsu ARUL9TLAV2 Operation Manual

Add to My manuals
6 Pages

advertisement

Fujitsu ARUL9TLAV2 Operation Manual | Manualzz
MODE D’EMPLOI
UNITÉ INTÉRIEURE (type conduit)
Conservez ce manuel pour pour toute référence ultérieure.
MANUAL DE FUNCIONAMIENTO
UNIDAD INTERIOR (Tipo conducto)
Conserve este manual para posibles consultas futuras.
English
Keep this manual for future reference.
Français
INDOOR UNIT (Duct type)
Español
OPERATING MANUAL
ARUL7TLAV2
ARUL9TLAV2
ARUL12TLAV2
ARUL14TLAV2
ARUL18TLAV2
PART No. 9374343447
9374343447_OM.indb cover1
7/30/2019 10:36:04 AM
OPERATING MANUAL
PART No. 9374343447
VRF system indoor unit (Duct type)
CONTENTS
SAFETY PRECAUTIONS........................................................................1
NAME OF PARTS ...................................................................................1
MANUAL AUTO OPERATION ................................................................2
OPERATING TIPS ..................................................................................2
CLEANING AND CARE...........................................................................3
TROUBLESHOOTING ............................................................................3
SPECIFICATIONS...................................................................................4
SAFETY PRECAUTIONS
● Do not apply any heavy pressure to radiator fins.
● Do not use flammable gases near the air conditioner.
● Do not touch the piping during operation.
● Ensure that any electronic equipment is at least 40 in (1 m) away from
either the indoor or outdoor units.
● This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
Note: Switching the operating mode in the heat recovery system may
require some time to prepare for operation. Please note that this is
not a fault.
PRECAUTIONS ON INSTALLATION
● Before using the appliance, read these “PRECAUTIONS” thoroughly
and operate in the correct way.
● The instructions in this section all relate to safety; be sure to maintain
safe operating conditions.
● “WARNING” and “CAUTION” have the following meanings in these
instructions:
WARNING
This mark indicates procedures which, if improperly performed, might lead to the death or
serious injury of the user.
CAUTION
This mark indicates procedures which, if improperly performed, might possibly result in personal harm to the user, or damage to property.
PRECAUTIONS ON USE
WARNING
● Do not keep exposing oneself to the direct wind of air conditioner for a
long time.
CAUTION
● Do not attempt to install this air conditioner by yourself.
● This unit contains no user-serviceable parts. Always consult authorized
service personnel for repairs.
● When moving, consult authorized service personnel for disconnection
and installation of the unit.
● The unit must be earthed (grounded).
● Make sure drain work is implemented properly for drainage.
● Avoid installing the air conditioner near a fireplace or other heating
apparatus.
● When installing the indoor and outdoor units, take precautions to prevent access by infants.
NAME OF PARTS
● Ceiling Concealed
● Do not insert fingers or objects into the outlet port or intake grilles.
● Except for EMERGENCY, never turn off main as well as sub breaker
of the indoor units during operation. It will cause compressor failure as
well as water leakage. First, stop the indoor unit by operating the control unit, converter or external input device and then cut the breaker.
Make sure to operate through the control unit, converter or external
input device.
● If the power supply cord of this appliance is damaged, it should only
be replaced by the authorized service personal, since special purpose
tools and specified cord are required.
● If any refrigerant happens to leak, extinguish any flames, ventilate the
room and get in touch with authorized service personnel.
CAUTION
● Do not place animals or plants in the direct path of the airflow.
● Wall Mounted / Floor Standing Concealed
● Do not direct airflow at fireplaces or heating apparatus.
● Do not block or cover the inlet port and outlet port.
● Do not climb on, or place objects on, the air conditioner.
● Do not set flower vases or water containers on top of air conditioners.
● Do not hang objects from the indoor unit.
● Do not place anything below the indoor unit that should not get wet.
● Always turn off the electrical breaker whenever cleaning the air conditioner or the air filter.
● Do not pour water or cleaning solvent on the unit directly, or wash the
unit with them.
● Do not expose the air conditioner directly to water.
● Do not operate the air conditioner with wet hands.
● Check the condition of the installation stand for damage.
● Operate only with air filters installed.
● Do not drink the water drained from the air conditioner.
1 Outlet Port
2 Intake Port
En-1
9374343447_OM.indb 1
7/30/2019 10:36:06 AM
Control unit (optional)
Types of remote controllers:
● Wireless remote controller
(Be sure to use after connecting receiver unit.)
● Wired remote controller
● Simple remote controller
For operation method, please refer to the Operating Manual of each
device.
MANUAL AUTO OPERATION
Use the MANUAL AUTO operation in the event the remote controller is
lost or otherwise unavailable.
OPERATING TIPS
Operation and Performance
About priority state and standby state
● Multiple indoor units can be connected within the same system. Depending on the system, choice of operating mode are limited.
Cooling priority
state
When the other indoor units within the same system
operate in cooling or dry mode, heating cannot be
selected at the same time.
Heating priority
state
When the other indoor units within the same system
operate in heating mode, cooling and dry mode can
not be selected at the same time.
Standby state
The standby state activates when 2 or more indoor
units start up at the same time in different mode.
Any indoor unit other than priority mode will wait in
standby state until priority mode changes (operation
starts as soon as priority is switched).
At this time, the OPERATION indicator lamp (green)
lights up and the TIMER indicator lamp (orange)
flashes (limited to only when receiver unit is connected).
*Limited to only when receiver unit is connected.
CAUTION
Do not press the MANUAL AUTO button with wet hands or pointed objects, otherwise an electric shock or malfunction may occur.
Starting Operation
Press the MANUAL AUTO button on the operating
control panel.
The operation can be set in the following setting.
Operating mode
AUTO:
When Auto mode cannot be selected, it will
operate in the same mode as the other indoor
unit in the same system. (When other indoor
unit in the same system doesn’t operate, the air
conditioner will operate in cooling.)
Fan speed
AUTO
Setting temperature
74°F (23°C)
Stopping Operation
Press the MANUAL AUTO button on the operating
control panel.
Emergency Heat
* It is available when this function is enabled. Please consult an authorized service personnel as to whether this function is effective.
Set emergency heat
During heating operation, press the MANUAL AUTO
button on the operating control panel.
Auxiliary heater will be primary heater, and the outdoor unit will stop.
The OPERATION Indicator Lamp (Green) blinks during emergency heating operation. (3 seconds on, 1 second off.)
Cancel emergency heat
During emergency heating operation, press the MANUAL AUTO button on the operating control panel.
Low ambient cooling
● When the outdoor temperature drops, the outdoor unit’s fans may
switch to Low Speed, or one of the fans may stop intermittently.
Heating performance
● Heating mode operates on the heat-pump principle, absorbing heat
from outdoor air and transferring that heat indoors. As a result, the
operating performance is reduced as outdoor air temperature drops.
If you feel that insufficient heating performance is being produced, we
recommend you use this air conditioner in conjunction with another
type of heating appliance.
● Heating mode heat your entire room by recirculating air throughout the
room, with the result that some time may be required after first starting
the air conditioner until the room is heated.
Microcomputer-controlled automatic defrosting
● When using the Heating mode under conditions of low outdoor air
temperature high humidity, frost may form on the outdoor unit, resulting in reduced operating performance. In order to prevent this kind of
reduced performance, this unit is equipped with a Microcomputer-controlled automatic defrosting function. If frost forms, the air conditioner
will temporarily stop, and the defrosting circuit will operate briefly (for
about 4 to 15 minutes).
During Automatic Defrosting operation, the OPERATION indicator lamp
(green) will flash (limited to only when receiver unit is connected).
Oil recovery operation
● Periodically, the oil recovery operation is performed in order to return
compressor oil to the outdoor unit.
During oil recovery operation, the OPERATION indicator lamp (green)
will flash (for about 10 minutes) (limited to only when receiver unit is
connected).
En-2
9374343447_OM.indb 2
7/30/2019 10:36:06 AM
Temperature and humidity range
● The temperature and humidity required for operating this product is as
shown in the following table.
Cooling/Dry Mode
Heating Mode
Outdoor
temperature
Please refer to the specification of outdoor units.
Indoor
temperature
About 64 to 90 °F DB
(18 to 32 °C DB)
Indoor humidity
About 50 to 86 °F DB
(10 to 30 °C DB)
About 80% or less
● If the air conditioner is operated under higher temperature conditions
than those listed, the built-in protection circuit may operate to prevent
internal circuit damage. Also, during Cooling and Dry modes, if the unit
is used under conditions of lower temperature than those listed above,
the heat-exchanger may freeze, leading to water leakage and other
damage.
● If the unit is used for long periods under high-humidity conditions,
condensation may form on the surface of the indoor unit, and drip onto
the floor or other objects underneath.
● Do not use this unit for any purposes other than the Cooling, Heating,
Dehumidifying, and air-circulation of rooms in ordinary dwellings.
CLEANING AND CARE
CAUTION
● Before cleaning the unit, be sure to stop the unit and disconnect the
power supply.
● Do not stand on an unstable platform when cleaning.
● When removing and replacing the air filters, be sure not to touch the
heat exchanger, as personal injury may result.
● Do not clean the inside of the unit by yourself. To clean the inside,
always consult authorized service personnel.
● When cleaning the unit’s body, do not use water hotter than 104°F
(40°C), harsh abrasive cleansers, or volatile agents like benzene or
thinner.
● If dirt is allowed to accumulate on the air filter, airflow will be reduced,
lowering operating efficiency and increasing noise.
During periods of normal use, the air filter should be cleaned every 2
weeks.
Cleaning the air filter
Cleaning
Cleaning the air filter
Remove dust with a vacuum cleaner or by washing. After washing, be
sure to allow it to dry thoroughly in a shady place before reinstalling.
When not using for an extended period
Leave the breaker on for at least 12 hours before starting operation
when it is to be used again.
Airflow is weak or stops:
● When Heating operation is started, indoor unit’s fan may temporarily
stop, to allow internal parts to warm up.
● During Heating operation, if the room temperature rises above the
thermostat setting, the outdoor unit will stop, and the indoor unit’s fan
will stop. If you wish to warm the room further, set the thermostat for a
higher setting.
● During oil recovery operation, the airflow may stop for approximately
10 minutes. (See page 2.)
● During Heating operation, the unit will temporarily stop operation (between 4 and 15 minutes) as the Automatic Defrosting mode operates.
(See page 2.)
● The fan may operate at low speed during Dry operation or when the
unit is monitoring the room’s temperature.
● In the monitor AUTO operation, the fan will operate at low speed.
Flashing lamps:
(Limited to only when receiver unit is connected)
● The Operation indicator lamp (green) flashes:
An oil recovery operation is being performed. (See page 2.)
● The Operation indicator lamp (green) flashes:
An automatic defrosting operation is being performed. (See page 2.)
● The Operation indicator lamp (green) and Timer indicator lamp (orange) are flashing alternately:
It has recovered from a power outage.
● The Operation indicator lamp (green) and Timer indicator lamp (orange) are flashing simultaneously:
It is operating in trial operation mode. Ask a manager as there may be
maintenance being conducted.
● The Operation indicator lamp (green) lights up and the Timer indicator
lamp (orange) flashes:
This is the standby state. (See page 2.)
Noise is heard:
● In the following conditions there are sounds of water flowing from the
indoor unit and the operation sound becomes loud. These are the
sounds of the flowing of refrigerant.
When operation starts
When oil recovery operation finishes
When automatic defrosting operation finishes
● During operation, a slight squeaking sound may be heard. This is the
result of minute expansion and contraction of the panel due to temperature changes.
● During Heating operation, a sizzling sound may be heard occasionally.
This sound is produced by the Automatic Defrosting operation. (See
page 2.)
Smells:
● Some smell may be emitted from the indoor unit. This smell is the
result of room smells (furniture, tobacco, etc.) which have been taken
into the air conditioner.
Fog comes out of the indoor unit:
● During Cooling operation, a thin mist may be seen emitted from the
indoor unit. This results from the sudden Cooling of room air by the air
emitted from the air conditioner, resulting in condensation and misting.
TROUBLESHOOTING
Steam comes out of the indoor unit:
● During Heating operation, the outdoor unit’s fan may stop, and steam
may be seen rising from the unit. This is due to the Automatic Defrosting operation. (See page 2.)
The following conditions are not breakdowns or operation failures.
Water is produced from the outdoor unit:
● During Heating operation, water may be produced from the outdoor
unit due to the Automatic Defrosting operation.
Doesn’t operate immediately:
● If the unit is stopped and then immediately started again, the compressor will not operate for about 3 minutes, in order to prevent fuse
blowouts.
● Whenever the electrical breaker is turned off then on again, the protection circuit will operate for about 3 minutes, preventing unit operation
during that period.
En-3
9374343447_OM.indb 3
7/30/2019 10:36:06 AM
The following conditions may not be breakdowns so
check again.
Doesn’t operate at all:
● Has there been a power failure?
● Has a fuse blown out, or a circuit breaker been tripped?
● Is the main power switch set to the OFF position?
● Are you trying to engage in an operation different from the priority
state? (See page 2.)
● Is it in standby state? (See page 2.)
The operation mode cannot be changed:
● Are you trying to change to an operation different from the priority
conditions? (See page 2.)
Poor Cooling (or Heating) performance:
● Did you adjust the room temperature settings (thermostat) correctly?
● Is the air filter dirty? (See page 3.)
SPECIFICATIONS
ARUL
7
TLAV2
MODEL
ARUL
9
TLAV2
ARUL
12
TLAV2
ARUL
14
TLAV2
POWER SOURCE
208/230 V ~ 60 Hz
AVAILABLE
VOLTAGE RANGE
187 to 253 V
ARUL
18
TLAV2
COOLING
CAPACITY
Btu/h
(kW)
7,500
(2.2)
9,500
(2.8)
12,000
(3.5)
14,000
(4.1)
18,000
(5.3)
HEATING
CAPACITY
Btu/h
(kW)
9,500
(2.8)
10,900
(3.2)
13,500
(4.0)
15,600
(4.6)
20,000
(5.9)
SOUND PRESSURE LEVEL
HIGH
dB [A]
28
29
30
34
34
● Is there a window or door open?
MED HIGH
dB [A]
26
27
28
32
31
● In the case of Cooling operation, is a window allowing bright sunlight to
enter? (Close the curtains.)
MED
dB [A]
25
25
27
30
29
MED LOW
dB [A]
24
24
26
28
27
LOW
dB [A]
22
22
24
25
25
QUIET
dB [A]
21
21
22
22
23
● Are the air conditioner’s inlet port or outlet port blocked?
● In the case of Cooling operation, are there heating apparatus and computers inside the room, or are there too many people in the room?
● Is the fan speed set to low?
Set the temperature lower than the room temperature and use it:
● Temperature does not fall down well. Temperature may not fall down
depending on the room conditions. (While high humidity or the room
temperature is high.) (See page 3.)
DIMENSIONS & WEIGHT
HEIGHT
[in (mm)]
7-13/16 (198)
In the following situations stop operation immediately
and get in touch with authorized service personnel.
7-13/16
(198)
WIDTH
[in (mm)]
27-9/16 (700)
35-7/16
(900)
● The problem cannot be solved even when the troubleshooting checks
have been performed.
DEPTH
[in (mm)]
24-7/16 (620)
● The FILTER indicator lamp (red) is flashing very fast (when receiver
unit is connected).
24-7/16
(620)
WEIGHT
[lbs (kg)]
● The wired remote controller or simple remote controller indicate Er
(when connected).
● It has burning smell.
● For details on marking the Flashing lamps, please refer to the Manual
of “IR Receiver Unit” or “Wired Remote Controller”.
37 (17)
40 (18)
49 (22)
● Acoustic Noise Information:
The maximum sound pressure level is less than 70 dB (A) for both
indoor unit and outdoor unit. According to IEC 704-1 and ISO 3744.
● Standard static pressure: 0.1 in WG (25 Pa)
En-4
9374343447_OM.indb 4
7/30/2019 10:36:06 AM
9374343447_OM.indb 7
7/30/2019 10:36:07 AM

advertisement

Related manuals

Download PDF

advertisement