Fujitsu ASTG12KMCB Operation Manual

Fujitsu ASTG12KMCB Operation Manual
OPERATING MANUAL
R32
REFRIGERANT
This Air Conditioner contains and
operates with refrigerant R32.
THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED
BY QUALIFIED PERSONNEL.
AIR CONDITIONER
Wall Mounted Type
Refer to Commonwealth, State, Territory and local legislation,
regulations, codes, installation & operation manuals, before
the installation, maintenance or service of this product.
Contents
Safety Precautions ..........................................................En-1
Indoor Unit Overview and Operations .............................En-3
Remote Controller Overview and Operations ..................En-4
Timer Operation...............................................................En-6
Human Sensor (Energy Saving) ......................................En-8
Demand Response and Indoor Unit Operation ...............En-8
General Informations on Operation .................................En-9
Care and Cleaning.........................................................En-10
Troubleshooting .............................................................En-12
ASTG09KMCB
ASTG12KMCB
Before using this product, read these instructions thoroughly and keep this manual for future reference.
Safety Precautions
To prevent personal injury, injury to others, or property damage, read this section carefully before you use this product, and be sure to comply to the
following safety precautions.
Incorrect operation due to failure to follow the instructions may cause harm or damage, the seriousness of which is classified as follows:
WARNING
CAUTION
This mark warns of death or serious injury.
This mark warns of injury or damage to property.
This mark denotes an action that is COMPULSORY.
This mark denotes an action that is PROHIBITED.
• Explanation of symbols displayed on the indoor unit or outdoor unit.
WARNING
This symbol shows that this appliance uses a flammable refrigerant. If the refrigerant is leaked and exposure to an external
ignition source, there is a risk of fire.
CAUTION
This symbol shows that the Operation Manual should be read carefully.
CAUTION
This symbol shows that a service personnel should be handling this equipment with reference to the Installation Manual.
CAUTION
This symbol shows that information is available such as the Operating Manual or Installation Manual.
WARNING
• The appliance contains no user-serviceable parts. Always
consult authorized service personnel for repairing, installation,
and relocation of this product.
Improper installation or handling will cause leakage, electric
shock, or fire.
• In the event of a malfunction such as burning smell,
immediately stop operation of the air conditioner, and
disconnect all the power supply by turning off the electrical
breaker or disconnecting the power plug. Then consult
authorized service personnel.
• Take care not to damage the power supply cable.
If it is damaged, it should only be replaced by authorized
service personnel.
• In the event of refrigerant leakage, be sure to keep away
from fire or any flammables, and consult authorized service
personnel.
• If you see lightning or hear thunder, there might be a lightning
strike.
To prevent electric shock hazard, turn off the air conditioner
by using the remote controller, and do not touch the unit or
the power plug during thunderstorm.
• The appliance shall be stored in a room without continuously
operating ignition sources (for example: open flames, an
operating gas appliance or an operating electric heater).
• The appliance shall be stored in a well-ventilated area.
• Be aware that refrigerants may not contain an odour.
• The appliance shall be stored so as to prevent mechanical
damage from occurring.
• Disposing of the product shall be done properly, in
compliance with national or regional regulations.
• During transportation or relocation of the indoor unit, pipes
shall be covered with the wall hook bracket for protection.
Do not move the appliance by holding the indoor unit pipes.
(The stress applied to the pipe joints may cause the
flammable gas to leak during operation).
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance.
(continued)
PART No. 9333003283
9333003283_OM_EN.indd 1
En-1
1/20/2017 9:13:21 AM
Safety Precautions (continued)
WARNING
• Do not install the unit in area filled with mineral oil such as a
factory or area containing a large amount of splashed oil or
steam such as a kitchen.
• Do not start or stop the operation of this product by inserting
or pulling out the power plug, or by turning on or off the
circuit breaker.
• Do not use inflammable gases near the unit.
• Do not expose yourself directly to the cooling airflow for
many hours.
• Do not insert your fingers or any other objects into outlet
port, open panel, or intake grille.
• Do not operate with wet hands.
• Do not use means to accelerate the defrosting process or to
clean the appliance, other than those recommended by the
manufacturer.
• Do not pierce or burn.
CAUTION
• Provide occasional ventilation during use.
• Always operate the unit with air filters installed.
• Ensure that any electronic equipment is at least 1 meter
away from either the indoor unit or outdoor unit.
• Unplug the power supply cable when not using the indoor
unit for an extended period.
• After long period of use, check whether the installation stand
does not deteriorate to prevent the unit from falling down.
• The airflow direction and the room temperature should be
carefully considered when you use this product in a room
with infants, children, elderly or sick persons.
•
•
•
•
• Do not place vase or water container on the unit.
• Do not place any other electrical products or household
belongings under indoor unit or outdoor unit.
Dripping condensation from the unit might get them wet, and
may cause damage or malfunction of your property.
• Do not expose the unit directly to water.
• Do not use this product for preservation of food, plants,
animals, precision equipment, art work, or other objects. This
may cause quality deterioration of those items.
• Do not expose animals or plants to the direct airflow.
• Do not drink the drainage from the air conditioner.
• Do not pull the power supply cable to disconnect the plug.
• Do not touch the aluminum fins of heat exchanger built-in
the indoor or outdoor unit to avoid personal injury when you
install or maintain the unit.
Do not direct the airflow at fireplaces or heating apparatus.
Do not block or cover the intake grille and the outlet port.
Do not apply any heavy pressure to radiator fins.
Do not climb on, place objects on, or hang objects from the unit.
Indoor unit accessories
Remote controller holder installation
1
3 Slide up
2
Screws
Insert
Remote
controller
Remote controller
holder
Tapping screws
(M3 × 12 mm)
WARNING
Take care to prevent infants and young children from accidentally swallowing the batteries.
Batteries
Air cleaning filters
Filter holders
CAUTION
• Do not attempt to recharge dry batteries.
• Do not use dry batteries that has been recharged.
Battery (R03/LR03/AAA × 2) loading and remote controller preparation
3
7
4
1
9
5
6
8
2
5
6
7
8
En-2
Press CLOCK ADJUST button to start clock setting.
Set the day of the week by pressing SELECT button (Monday to
Sunday). *By pressing the TEMP. () buttons, the time indicator
can be changed from a 24-hour to a 12-hour clock.
Press NEXT button to continue.
Set the time by pressing SELECT button.
Pressing  or  changes the value by the minute.
Pressing down on  or  changes the value by 10 minutes.
9
To complete, press the SEND button close to the indoor unit.
Settings may not be properly sent if pressed from a distance.
Notes:
• Use specified type of batteries only.
• Do not mix different types or new and used batteries together.
• Batteries can be used about 1 year in ordinary use.
• If the remote control range noticeably shortens, replace the batteries, and press RESET button as shown in page 5.
OPERATING MANUAL
9333003283_OM_EN.indd 2
1/20/2017 9:13:21 AM
AIR CONDITIONER Wall Mounted Type
Indoor Unit Overview and Operations
1
Intake grille
11
Before starting operation, make sure that the intake grille has been
shut completely. Incomplete closing may have an effect on the proper
function or performance of the product.
2
TIMER indicator (orange)
Lights in TIMER operation, and blinks slowly when the timer setting
error is detected.
For details, refer to “Auto-restart function” on page 9.
MANUAL AUTO button
2
Use when the remote controller is lost or there is a malfunction.
Status
In operation
Stopping
After cleaning
Action
3
Mode or operation
Press more than 3 seconds.
Press more than 3 seconds and
less than 10 seconds.
Press more than 10 seconds.
(Only for servicing.*)
Press less than 3 seconds.
Stop
AUTO
1
Forced cooling
15
4
Filter indicator reset
*:To stop forced cooling, press this button or START/STOP button on
the remote controller.
3
WLAN adapter is build-in for wireless LAN control.
For details, refer to the setting manual of the Wireless LAN control.
NOTES:
• The indicators can be turned off by using the mobile app.
4
Front panel
5
Human Sensor
6
7
13
8
9
10
12
11
Vertical airflow direction louver
Each time you press SET button on the remote controller, the angle
of the vertical airflow direction louver moves as follows:
COOL or DRY mode
1*
4
5
6 7
2
3
HEAT mode
5
4
7*
6
Power diffuser
In conjunction with movement of the vertical airflow direction louver,
the angle of the power diffuser moves as follows:
Vertical airflow
direction louver
1
Power diffuser
1
2
3
5
4
2
12 OPERATION indicator (green)
Lights in normal operation, and blinks slowly in Automatic defrosting
operation.
Blinks during Demand Response operation. For details, refer to page
8.
13
*: Default setting in each mode.
• Do not adjust by hand.
• At the beginning of AUTO or HEAT mode, they may stay on position
1 for a while for adjustment.
• If the angle is set to position 4–7 for more than 30 minutes in COOL
or DRY mode, the louver will automatically return to position 3.
• Keeping the position 4-7 during COOL or DRY mode may cause
condensation to form, and the drops may damage your property.
7
6
14
See page 8
Used for Energy Saving Program. Controls temperature setting by
detecting people in the room.
1
2
3
5
Wireless LAN control indicator and buttons
6
3
Horizontal airflow direction louvers
CAUTION
Before you adjust the horizontal airflow direction, make sure that
the vertical airflow direction louver has been stopped completely.
Adjust two knobs by hand.
14
Air filter
See page 10
15
Air cleaning filters
See page 11
Purify or deodorize the air, and provide fresh airflow.
7
4
• In SWING operation, power diffuser does not move.
8
Drain hose
9
Remote controller signal receiver
CAUTION
For appropriate signal transmission between remote controller and
indoor unit, keep the signal receiver away from the following items:
- Direct sunlight or other strong lights
- Flat-panel television screen
In rooms with instantaneous fluorescent lights, such as inverter type ones, the signal may not be transmitted properly. In
such a case, consult the store of purchase.
10
ECONOMY indicator (green)
Lights in ECONOMY operation and in 10 °C HEAT operation.
OPERATING MANUAL
9333003283_OM_EN.indd 3
En-3
1/20/2017 9:13:21 AM
Remote Controller Overview and Operations
CAUTION
• To prevent malfunction or damage of the remote controller:
- Place remote controller at where will not be exposed to
direct sunlight or excessive heat.
- Remove batteries if the product is not going to be used for
an extended period.
- Exhausted batteries must be removed immediately, and
be disposed according to the local laws and regulations of
your region.
• If leaking battery fluid comes in contact with your skin, eyes,
or mouth, immediately rinse with plenty of clean water, and
consult your physician.
• Obstacles such as a curtain or wall between the remote
controller and the indoor unit may affect the appropriate
signal transmission.
• Do not apply strong shocks to the remote controller.
• Do not pour water on the remote controller.
7
8
24
9
2
23
10
22
11
21
12
20
13
19
14
18
15
17
16
You can quickly start operation with the following 3 steps:
1
START/STOP button
2
MODE button
Switches operation mode in following order.
AUTO
COOL
DRY
FAN
HEAT
Notes in HEAT mode:
• At the beginning of the operation, the indoor unit operates at very
low fan speed for about 3–5 minutes for preparation, then switches
to the selected fan speed.
• Automatic defrosting operation overrides the heating operation when
necessary.
3
TEMP. (temperature) buttons
Sets the desired temperature.
In COOL or DRY mode, the temperature needs to be set lower than
the current room temperature. In HEAT mode, the temperature needs
to be set higher than the current room temperature.
Otherwise, corresponding operation mode may not start.
Temperature setting range
AUTO/COOL/DRY
18.0–30.0 °C
HEAT
16.0–30.0 °C
Notes: Temperature control is not available in FAN mode.
4
4
Remote controller display
In this section, all the possible indicators are displayed for description.
In actual operation, the display is linked with the button operation, and
only shows the necessary indicators for each setting.
6
3
5
1
5
POWERFUL button
Activates the POWERFUL operation.
The unit will operate at maximum power and strong airflow to quickly
cool down or warm up the room.
When activated, the indoor unit will emit 3 short beeps.
To turn off, press the POWERFUL button again. The indoor unit will
then emit 2 short beeps.
POWERFUL operation is automatically turned off in the following
situations:
• Adjusted room temperature reaches the set temperature in COOL,
DRY, or HEAT mode.
• 20 minutes have passed after the POWERFUL operation mode has been set.
Even in situations above, the POWERFUL operation will not
automatically turn off unless it has run for a certain amount of time.
Notes:
• The airflow direction and the fan speed are controlled automatically.
• This operation cannot be performed simultaneously with ECONOMY
operation.
• POWERFUL operation will override the OUTDOOR UNIT LOW
NOISE, ENERGY SAVING functions. Both functions, if set, will start
after the POWERFUL operation is turned off.
6
10 °C HEAT button
Starts 10 °C HEAT operation that maintains the room temperature at
10 °C so as to prevent the room temperature to drop too low.
After pressing the button to start the 10 °C HEAT operation, the
indoor unit emits 2 short beeps and the ECONOMY indicator (green)
will turn on.
To turn off, press the START/STOP button. The Economy indicator
will turn off.
Notes:
• In 10 °C HEAT operation mode, only the vertical airflow direction
can be adjusted by using the SET button.
• HEAT mode will not be performed if the room temperature is warm enough.
(continued)
En-4
OPERATING MANUAL
9333003283_OM_EN.indd 4
1/20/2017 9:13:22 AM
AIR CONDITIONER Wall Mounted Type
Remote Controller Overview and Operations (continued)
7
Signal transmitter
19 SEND button
Aim at the signal receiver of the indoor unit properly.
• Signal transmit indicator on the remote controller display shows
that the signal from the remote controller is being transmitted.
• Operating range is approximately 7 m.
• You will hear a beep if the transmitted signal has been sent properly.
If there is no beep, press the button on the remote controller again.
8
(HIGH)
(MED)
(LOW)
(QUIET)
• When AUTO is selected, the fan speed is automatically adjusted
according to the operation mode.
SWING button
Starts or stops automatic swing of the vertical airflow direction louver.
• The Swing operation range will differ by mode as follows:
1
2
3
COOL, DRY, or FAN
mode
4
1
5
2
3
HEAT or FAN mode
4
5
6
7
6 7
Notes:
• SWING operation may stop temporarily when the indoor unit fan is
rotating at very low speed or is stopped.
• In FAN mode, swing operation range of 1  3 or 4  7 is decided
according to the airflow direction previously set before starting the
swing operation.
10 SET button
See page 3
Adjusts the vertical airflow direction.
11
See page 6
Used to enter the timer setting mode.
21 SELECT button
22
Controls the fan speed.
9
20 TIMER SETTING button
Used for adjusting the clock or timer.
FAN button
(AUTO)
Used for sending the timer/clock setting.
WEEKLY timer button
See page 6
Activates the WEEKLY timer for a maximum of 4 on or off programs
per day, each day of the week.
12 SLEEP timer button
See page 6
Activates the SLEEP timer that helps you to fall asleep comfortably
with gradual temperature control.
13 ON/OFF timer button
See page 6
OUTDOOR UNIT LOW NOISE button
Starts or stops OUTDOOR UNIT LOW NOISE operation that lowers
noise generated from the outdoor unit by cutting down the rotation
number of the compressor, and suppressing the fan speed.
Once the operation is set, the setting is preserved until you press this
button again to stop the operation, even if the indoor unit operation is
stopped.
on the remote controller display shows that the unit is in
OUTDOOR UNIT LOW NOISE mode.
Notes:
• This operation cannot be performed simultaneously with FAN, DRY
and POWERFUL operation modes.
23
ECONOMY button
Starts or stops ECONOMY operation that saves more electricity
than other operation modes by changing the set temperature to a
moderate setting.
By pressing the ECONOMY button, the ECONOMY indicator on the
indoor unit turns on.
• In COOL or DRY mode, the room temperature will be adjusted a few
degrees higher than the set temperature.
• In HEAT mode, the room temperature will be adjusted a few
degrees lower than the set temperature.
Notes:
• In COOL, HEAT, or DRY mode, the maximum output of this
operation is approximately 70 % of usual air conditioning operation.
• This operation cannot be performed during temperature monitoring
by AUTO mode.
24
SENSOR button (ENERGY SAVING PROGRAM)
See page 8
Activates or deactivates the energy saving program.
* The Energy Saving program is ON at the time of purchase.
: The setting must be done while the setting screen is displayed for
each function.
: The button is controllable only when the air conditioner is on.
Activates the ON/OFF timer.
14 NEXT button
Used for adjusting the timer setting.
15 BACK button
Used for adjusting the timer setting.
16 RESET button
When you press the RESET button, press it gently by using the tip of
a ballpoint pen or other small object in correct direction as shown in
this figure.
RESET
17 TEST RUN button
See page 2
Only used for the initial test in the unit installation.
Do not press this button under normal use because it will cause
incorrect operation.
• During the test run, the OPERATION indicator and the TIMER
indicator blink simultaneously.
• To quit the test run that is started unintentionally, you need to turn
off the air conditioner by pressing the START/STOP button.
18 CLOCK ADJUST button
See page 2
Used for adjusting the clock.
OPERATING MANUAL
9333003283_OM_EN.indd 5
En-5
1/20/2017 9:13:23 AM
Timer Operation
 Remote controller custom code setting
When two or more air conditioners are installed in a room and the
remote controller is operating an air conditioner other than the one you
wish to set, change the custom code of the remote controller to operate
only the air conditioner you wish to set (4 selections possible).
When two or more air conditioners are installed in a room, please
contact your retailer to set the individual air conditioner custom codes.
Use the following steps to select the custom
code of the remote controller.
(Note that the air conditioner cannot receive
a signal if the air conditioner has not been set
for the matching custom code.)
1. Press the START/STOP button until only the
clock is displayed on the remote controller
display.
2. Press the MODE button for at least five
seconds to display the current custom code
(initially set to A).
3. Press the SET TEMP. (
between A↔B↔C↔D.
/
) button to change the custom code
Note for timer settings:
Any interruption of the power supply, such as a blackout or cutting off
of a circuit breaker, makes the set internal clock incorrect.
In such a case, the TIMER indicator on the indoor unit blinks, and you
need to readjust the setting.
ON timer or OFF timer
You can set the ON timer or OFF timer with the following steps.
1
Press the TIMER SETTING button to start the setting.
The WEEKLY indicator will be flashing on the remote controller.
2
Press the SELECT button to choose the desired mode. The mode
will change as follows:
WEEKLY
• If no buttons are pressed within 30 seconds after the custom code
is displayed, the system returns to the original clock display. In this
case, start again from step 1.
• The air conditioner custom code is set to A prior to shipment.
Contact our authorized service personnel to change the custom code.
• Depending on the remote controller, the custom code may return to
custom code A when the batteries are replaced. In this case,if you
use a code other than A, reset the code after replacing the batteries. If you do not know the air conditioner custom code setting,try
each code A↔B↔C↔D until you find the code which operates the
air conditioner.
When you use remote controller, there are following different points as
compared with using wireless remote controller.
[The additional functions for wired remote controller]
• Temperature set back timer
And, you can use wired and wireless remote controller together.
However, you must change some restricted functions of wireless remote
controller to invalid.
If restricted function is valid, remote controller cannot use correctly.
(beeping sound will be heard, OPERATION, TIMER and the ECONOMY
indicator of the indoor unit will flash.)
[The restricted functions for wireless remote controller]
<Polar 3-core wired remote controller>
• Outdoor unit low noise
• Energy saving
• 10°C HEAT
• Powerful
• Timer operation
ON/OFF
(ONOFF)
SLEEP
(OFF)
Press the NEXT button. Continue to setting for each mode.
* To cancel timer setting during the setting process, press the
TIMER SETTING button again.
4
Adjust the time by pressing the SELECT button while the clock
indicator is blinking. Each time you press the button, the time will
change by +5/-5 minutes. Pressing down will change the time by
+10/-10 minutes.
5
Press the SEND button.
To redo the timer setting, perform step 1 to 5 again.
To cancel the ON/OFF timer, press the ON/OFF button while the ON/
OFF indicator is on. (Erases the indicator)
Program timer (combined use of the ON timer and the OFF timer)
You can set an integrated ON–OFF or OFF–ON timer.
Either of the timer whose configured starting time is closer to the
current time works first, and the order of timer operation is displayed
as follows:
Timer
Indicator on remote controller display
ON–OFF timer
OFF–ON timer
 Wired Remote Controller (Option)
The optional wired remote controller can be used.
ON/OFF
(OFF)
3
Match the code on the display to the air conditioner custom code.
4. Press the MODE button again to return to the clock display. The
custom code will be changed.
ON/OFF
(ON)
To set the program timer, conduct the same steps 1~5 for the ON/
OFF timer. (Select ONOFF in Step 2)
Notes:
• If you change the setting value for the timer after the program timer
is set, the counting down of the timer will be reset at that moment.
• Time setting for each combination should be within a span of 24 hours.
SLEEP timer
To set the SLEEP timer, first follow steps 1~3 for the ON/OFF timer.
4
Adjust the time by pressing the SELECT button while the clock
indicator is blinking.
Each time you press the button, the time changes as follows:
0H
1H
30M
00M
(30 min.)
5
2H
00M
3H
00M
5H
00M
7H
00M
9H
00M
hours
Press the SEND button.
To cancel the SLEEP timer, press the SLEEP button while the SLEEP
indicator is on. (Erases the indicator)
To help you to fall asleep comfortably and prevent excessive warming
or cooling in sleep, the SLEEP timer controls the temperature setting
automatically in accordance with the set time shown as follows. The
air conditioner completely turns off after the set time has elapsed.
In HEAT mode
In COOL or DRY mode
1 °C 2 °C 3 °C 4 °C
Set
temperature
30 min.
1 hour
1.5 hour
Set time
Set time
1 hour
1 °C
2 °C
(continued)
En-6
OPERATING MANUAL
9333003283_OM_EN.indd 6
1/20/2017 9:13:23 AM
AIR CONDITIONER Wall Mounted Type
Timer Operation (continued)
WEEKLY timer
ON and OFF timer can be combined, and up to 4 reservations (program
) per day and 28 reservations per week.
Before setting the program, please set the week and time of the air
conditioner first.
If the week and time are not set, the weekly timer will not operate
correctly at the set time.
Please refer to "remote controller preparation" (page 2).
To set the WEEKLY timer, first follow steps 1~3 on page 6 for the ON/
OFF timer.
4
Select the program number and the day using the SELECT
button.
Example of WEEKLY timer 1
Program
Monday to
Friday
7:00 ON 24°C
Wake up
Leave for work
Come back home
9:00 OFF
11:00 OFF
Program
Program
Program
ON
Program
1Week
Program
Monday
Tuesday
Program
Sunday
ON
Program
Saturday Program
Sunday
Press the NEXT button, when the program number and day you
want to set are flashing.
No timer settings
Program
Monday Program
Go to sleep
5
Sunday ON
Program
17:00 ON 26°C 23:00 OFF
9:00 OFF
Saturday
1Week
Program
Program
Program
Program
17:00 OFF
ON
Using the SELECT button select the operation mode(ON timer,
OFF timer, or without a timer).
23:00 OFF
Example of WEEKLY timer 2
You can specify a given temperature in the ON setting in WEEKLY
timer.
Program
Program
7:00 ON 22°C
9:00 ON 24°C 17:00 ON 26°C 23:00 ON 22°C
Program
Program
* You can set the temperature for AUTO, COOL, and DRY modes within
the range of 18-30°C, for Heat mode the range is 10 or 16-30°C.
Even if you set to 10, 16, or 17°C, if you run the product on AUTO,
COOL, or DRY, it will run at 18°C.
Notes:
• Operations modes other than the temperature setting will be the
same at the last time operation was stopped, so Cooling → Heating
→ Cooling → Heating type of operations cannot be automatically
set.
• If you set the ON timer and OFF timer on the same time, the air
conditioner will run the ON timer. If two ON timer are set at the same
time, the air conditioner will run in the order of the program number.
• If there is a power interruption, such as due to a power outage
during the WEEKLY timer setting or a circuit breaker cutting out,
the internal timer of the air conditioner will be incorrect. (See page
9 "Auto-restart".) In such a case, the main timer lamp will notify you
of this by flashing, so carry out matching of the time and date. (See
page 2 "remote controller preparation".)
• You cannot use the WEEKLY timer together with the other timers.
If you want to run the product on WEEKLY timer after using the ON/
OFF Timer, Program Timer, or SLEEP Timer while the WEEKLY
timer is running, you need to activate the WEEKLY timer again.
To operate without a timer
1. Press the NEXT button to go back to step 4 and configure the
next setting.
2. Press the SEND button to finish
Press the NEXT button.
6
Press the SELECT button to set the desired ON time or OFF
time.
If you selected OFF in step 5
1. Press the NEXT button to go back to step 4 and configure the
next setting.
2. Press the SEND button.
Press the NEXT button.
7
Press the SELECT button to set the temperature.
If you want to move on to the next setting, press the NEXT button,
return to step 4 and configure the next setting.
8
To complete the setting, press the SEND button.
If you want to cancel the setting midway, please press the
TIMER SETTING button instead of pressing the SEND button.
Notes:
● When canceling the WEEKLY timer, select No Timer Operation in
Step 5 in the WEEKLY timer setting.
● If you want to go back to the previous step when configuring
settings, press the BACK button to return to the previous step.
● Press the SEND button, when you are close to the main unit. If you
do so when far from the main unit, the signal may not get properly
sent, and the settings may not get properly configured.
● To check the schedule, repeat steps 1 to 3 to enter the WEEKLY
timer mode, then use the SELECT button to browse through the
WEEKLY timer settings in the order shown in step 4.
● To cancel the WEEKLY timer, press the WEEKLY button while the
WEEKLY indicator is on. (Erases the indicator)
OPERATING MANUAL
9333003283_OM_EN.indd 7
En-7
1/20/2017 9:13:23 AM
Human Sensor (Energy Saving)
To prevent waste of electricity, this function controls the temperature
setting when no one is occupying the room. Energy Saving program is
on at the time of purchase.
1
2
● Application range is follows.
Vertical angle 90° (Side view)
To activate the Energy Saving program, press the SENSOR
button.
indicator will be flashing on the remote controller
display.
To deactivate the Energy Saving program, press the SENSOR
button again.
will no longer be shown on the remote controller
display.
About the ENERGY SAVING Operation
If no one enters the room for approximately 20 minutes, the set
temperature will be automatically controlled.
(When someone comes back into the room, the human sensor will
detect this, and automatically revert to the original settings.)
Operation
mode
Operating details
(if there is no one in the room for a while)
The set temperature will be increased by a maximum of
COOL/DRY
approximately 2˚C.
HEAT
The set temperature will be decreased by a maximum
of approximately 4˚C.
AUTO
This runs the ENERGY SAVING function automatically
for the selected mode (Cooling/ Heating/ Drying).
● When using together with the SLEEP timer (page 6), the SLEEP
timer will be prioritized.
● During 10°C HEAT operation, if there is no one in the room the set
temperature will not be changed.
7m
Horizontal angle 100° (Top view)
7m
90°
50°
50°
ENERGY SAVING function may not work when the room temperature is
very different from the temperature defined in temperature setting, such
as when immediately after starting the operation.
About the HUMAN SENSOR
● Details about detection with the human sensor
● The human sensor detects whether there are people in the room
by looking for movement by people in the room.
Notice
● Since the human sensor detects infrared light given out by
people, there may be cases where this detection is incorrect.
Situations in which the sensor will detect no people in the
room, even when there is someone there
● When the temperature is high and the difference with between people’s body temperature is small.
(Such as during the summer when the temperature is 30˚C
or higher)
● When there is someone in the room, but they do not move
for a long period of time.
● When someone is hidden behind a sofa, other furniture,
glass, or in similar situations.
● When someone is wearing extremely thick clothing and has
their back facing the sensor.
Situations in which the sensor will incorrectly detect people
in the room, even when there is no one there
● When there is a dog or a cat moving around in the room.
● When the wind is making curtains or plants move.
● When there are heating units, humidifiers, or electric appliances such as oscillating electric fans operating.
Demand Response and Indoor Unit Operation
This product is designed to be compatible with Air Conditioning Demand
Response program.
To utilize the function, you need a separate arrangement with your
electricity supplier. Please check availability in the place of use.
When your electricity supplier activates one of the following 3 Demand
Response (DR) modes, the air conditioner switches over to the
appropriate operation, and the OPERATION indicator (green) on the
indoor unit blinks to inform you the unit has entered the DR mode.
DR mode
Compressor off.
DR mode 2
The air conditioner continues to cool or heat during
the Demand Response event, but the electrical energy
consumed by the air conditioner in a half hour period
is not more than 50% of the total electrical energy that
would be consumed if operating at the rated capacity in
a half hour period.
DR mode 3
The air conditioner continues to cool or heat during
the Demand Response event, but the electrical energy
consumed by the air conditioner in a half hour period
is not more than 75% of the total electrical energy that
would be consumed if operating at the rated capacity in
a half hour period.
OPERATION indicator
(indoor unit)
Blinking pattern and the intervals are as follows :
● AUTO/COOL/HEAT/DRY/FAN operations
ON (4 seconds)
OFF (0.5 seconds)
OFF (0.5 seconds)
● 10˚C HEAT operation
OFF (4 seconds)
ON (0.5 seconds)
ON (0.5 seconds)
ON (0.5 seconds)
OFF (0.5 seconds)
The indicator will keep blinking until the unit finishes the function.
En-8
Description of operation in this mode
DR mode 1
When the unit enters the DR mode, it performs moderate operation so
the cooling or heating effect may be reduced. You cannot override this
function by changing the temperature setting using the remote controller
or other actions unless the unit finishes the function.
Note: Stopping the operation of the air conditioner by using the remote
controller or by OFF timer are valid in DR mode.
If the timer operation is interfered by an interruption of power
supply such as a blackout and the power supply is resumed, no
indication of the DR mode is performed.
During the DR mode, no indication of "filter sign" is performed.
Powerful operation is performed within the operable range of the
DR mode.
When the unit finishes the function, it will perform the operation that was
previously performed before entering the DR mode.
If you have operational issues, contact your electricity supplier first to
check whether they are activating any of the DR mode described above.
If the air conditioner is under demand controlling, consult the issues with
your electricity supplier.
If they are not demand controlling the air conditioner, refer to your
warranty card for the contact details of Fujitsu General (AUST.) PTY
LIMITED or visit our website : www.fujitsugeneral.com.au
OPERATING MANUAL
9333003283_OM_EN.indd 8
1/20/2017 9:13:24 AM
AIR CONDITIONER Wall Mounted Type
General Informations on Operation
Automatic defrosting operation
Heating performance
When outdoor temperature is very low with high humidity, frost
may form on the outdoor unit during the heating operation, and
it could reduce the operating performance of the product.
For frost protection, a microcomputer-controlled automatic
defrost function is equipped in this air conditioner.
If frost forms, the air conditioner will temporarily stop, and
defrost circuit will operate briefly (maximum of 15 minutes.)
OPERATION indicator on the indoor unit blinks during this
operation.
If frost forms on the outdoor unit after the heating operation, the
outdoor unit will stop automatically after it operates for a few
minutes. Then the automatic defrosting operation starts.
• This air conditioner operates on the heat-pump principle,
absorbing heat from air outdoors and transferring that heat
to the indoor unit. As a result, the operating performance is
reduced as outdoor air temperature drops. If you feel that the
heating performance is insufficient, we recommend you to use
this air conditioner in conjunction with other kinds of heating
appliance.
Auto-restart function
In event of power interruption such as a blackout, the air
conditioner stops once. But it restarts automatically and
performs previous operation when the power supply is resumed.
If any power interruption occurs after the timer is set, counting
down of the timer will be reset.
After the power supply is resumed, the TIMER indicator on the
indoor unit blinks to notify you that there has been a timer fault.
In such a case, reset the timer for your opportune time.
Malfunctions caused by other electrical devices:
Use of other electrical appliances such as an electric shaver or
nearby use of a wireless radio transmitter may cause the malfunction
of the air conditioner.
If you encounter such a malfunction, turn off the circuit breaker once.
Then turn it on again, and resume operation by using the remote
controller.
Temperature and Humidity Range
Permissible ranges of temperature and humidity are as follows:
COOL/DRY
HEAT
Indoor temperature
About 18 °C to 32 °C
Indoor humidity
Below approximately 80%.
If the air conditioner is used continuously for many
hours, water may condense on the surface and drip.
Indoor temperature
About 16 °C to 30 °C
If the unit is used under higher temperature conditions than those noted here, the automatic protection circuit may operate, interrupting the operation.
If the unit is used under lower temperature conditions than those noted here, the heat exchanger may freeze, causing water leakage or other malfunction.
● Do not use the air conditioner for any purpose other than room cooling/dry, room heating or fan.
OPERATING MANUAL
9333003283_OM_EN.indd 9
En-9
1/20/2017 9:13:25 AM
Care and Cleaning
CAUTION
• Before cleaning the indoor unit, be sure to turn it off and all the power supply has been disconnected.
• Before starting operation, make sure that the intake grille has been shut completely. Incomplete closing of the intake grille might have an
effect on the proper working or performance of the air conditioner.
• Do not touch the aluminum fins of heat exchanger built-in the indoor unit to avoid personal injury when you maintain the unit.
• Do not expose the indoor unit to liquid insecticides or hair sprays.
• Do not stand on slippery, uneven or unstable surfaces when you maintain the unit.
Daily care
Cleaning the air filters
When cleaning the indoor unit body, mind the following:
• Do not use water hotter than 40 °C.
• Do not use scouring cleanser, volatile solvents such as benzene or
thinner.
• Wipe the unit gently by using soft cloth.
Cleaning the intake grille
1
Open the intake grille in direction of the arrow a. While gently
pressing the left and right mounting shafts of the intake grille
outward b, remove the intake grille in direction of the arrow c.
Mind that you have a periodical cleaning of the air filters to prevent
reducing the operation efficiency of the product.
Using of clogged air filter with dust will lower the product performance,
and may cause airflow reduction or increase of operating noise.
Clean the air filters once every 2 weeks under normal use.
1
Open the intake grille.
(Refer to a of step 1 in “Cleaning the intake grille”.)
2
While holding the intake grille with your hand, pull up the handle
a of the filter in direction of the arrow and release the 2 claws b.
Then pull the filter out with gently sliding it downward c.
a
c
c
c
a
b
b
b
3
a
a
b
Filter holder and air cleaning filter are attached on the rear side
of the air filter. Remove them from the air filter by unlatching each
corner of the filter holder d.
d
d
2
Wash the intake grille gently with water or wipe it gently with a
soft cloth moisten with warm water.
Then wipe it with a dry and soft cloth.
3
While holding the grille horizontal, set the left and right mounting
shafts into the pillow blocks at the top of the panel a. To latch
each shaft properly, insert the shaft until it snaps.
Then close the intake grille b.
a
a
d
d
4
Remove dust by using a vacuum cleaner or by washing the filter.
When you wash the filter, use neutral household detergent and
warm water.
After rinse the filter well, dry it throughly in a shaded place before
you reinstall it.
5
Attach the air cleaning filter and the filter holder to each air filter.
6
Attach the air filter with aligning both side of the filter with the front
panel, and push in the filter fully.
Note:
Make sure that 2 claws are firmly snapped to the guide holes on
the panel.
b
b
4
En-10
7
Close the intake grille firmly.
(Refer to step 4 in “Cleaning the intake grille”.)
Press 4 places on the intake grille to close it completely.
OPERATING MANUAL
9333003283_OM_EN.indd 10
1/20/2017 9:13:25 AM
AIR CONDITIONER Wall Mounted Type
Care and Cleaning
Replacing the air cleaning filter
1
Remove the air filter. (Refer to step 1 in “Replacing the air filter”.)
2
Release 2 latches a of the filter holder, and turn over the holder
in direction of arrow b.
Remove the soiled air cleaning filter c.
Note:
Air cleaning filter is attached on each air filter.
a
a
b
Following 2 types of air cleaning filters are used in this product.
When you replace them, purchase dedicated air cleaning filters for this
product.
Apple-catechin filter: UTR-FA16
(1 sheet)
The Apple-catechin filter uses static electricity to clean fine particles
and dust in the air such as tobacco smoke and plant pollen that are
too small to see.
• This filter is disposable. Do not wash or reuse it.
• Once you open the package, use it as soon as possible. The
cleaning effect is reduced if the filter is left with the package opened.
• Replace the filter once every 3 months under normal use.
• By setting the fan speed high, the air cleaning effect increases.
Ion deodorization filter: UTR-FA16-2
(Light blue, 1 sheet)
c
3
Attach new or maintained air cleaning filter d to the filter holder.
New air cleaning filter can be attached to either of the right holder
or the left holder.
d
4
The filter deodorizes by powerfully decomposing absorbed odors
using the oxidizing and reducing effects of ions generated by the
ultra-fine-particle ceramic.
• To maintain the deodorizing effect, clean the filter once every 3
months as follows:
1. Remove the filter.
2. Flush the filter with high-pressure hot water until the surface of
the filter is covered with water.
3. Wash the filter gently with diluent neutral detergent. Do not wash
it by wringing or rubbing to prevent reducing the deodorizing
effect by damage.
4. Rinse the filter well with water flow.
5. Dry the filter throughly in a shaded place.
6. Reinstall the filter to the indoor unit.
• Replace the filter once every 3 years under normal use.
Latch 2 corners of the filter holder e to the air filter firmly.
After extended non-use of the unit
e
e
If you have shut down the indoor unit for 1 month or more, perform the
FAN operation for half a day to dry the internal parts throughly before
you perform normal operation.
Additional inspection
5
Reinstall the air filter. (Refer to step 6 in “Cleaning the air filter”.)
6
Close the intake grille firmly.
(Refer to step 4 in “Cleaning the intake grille” on page 10.)
After long period of use, accumulated dust inside the indoor unit may
reduce the product performance even if you have maintained the unit
with instructed daily care or cleaning procedures written in this manual.
In such a case, a product inspection is recommended.
For more information, consult authorized service personnel.
OPERATING MANUAL
9333003283_OM_EN.indd 11
En-11
1/20/2017 9:13:26 AM
Troubleshooting
WARNING
In following events, immediately stop operation of the air conditioner, and disconnect all the power supply by turning off the electrical
breaker or disconnecting the power plug. Then consult your dealer or authorized service personnel.
As long as the unit is connected to the power supply, it is not insulated from the power supply even if the unit is turned off.
• Unit smells of something burning or emits smoke
• Water leaks from the unit
Following symptoms do not indicate product malfunction, but they are normal functions or characteristics of this product.
Symptom
Operation is delayed after
restart.
Noise is heard.
Cause
To prevent blowout of the fuse, the compressor will not operate while the protection circuit is working
for about 3 minutes after sudden OFF→ON operation of the power supply.
• During operation or immediately after stopping the air conditioner, refrigerant flowing sound may be
heard. Also it may be particularly noticeable for 2–3 minutes after starting operation.
• During the operation, a slight squeaking sound produced by the minute expansion and contraction
of the front panel caused by temperature change may be heard.
See page
–
–
During heating operation, a sizzling sound produced by the automatic defrosting operation may be
heard.
9
Smell coming from the unit.
Various smells generated from interior textile, furniture, or cigarette smoke absorbed into the air
conditioner may be emitted.
–
Mist or steam is emitted from
the unit.
In COOL or DRY mode, a thin mist generated by condensation formed with sudden cooling process
may be emitted.
–
During heating operation, the fan built-in the outdoor unit may stop and rising steam generated by the
automatic defrosting operation may be seen.
9
• Immediately after the heating operation is started, the fan speed stays very low temporarily to warm
up the internal parts of the unit.
• In HEAT mode, the outdoor unit stops and the indoor unit operates at very low fan speed if the
room temperature rises above the set temperature.
–
In HEAT mode, the indoor unit temporarily stops for maximum of 15 minutes to perform the automatic
defrosting operation while the OPERATION indicator is flashing.
9
In DRY mode, the indoor unit operates at low fan speed to adjust the room humidity, and may stop
from time to time.
–
When the fan speed is set to “QUIET”, the fan rotates at very low speed and the airflow is reduced.
–
Airflow is weak or stops.
Outdoor unit emits water.
In COOL mode, the indoor unit fan may stop from time to time when the outdoor unit is stopped.
4
When monitoring operation is performed in AUTO mode, the fan rotates at very low speed.
–
During heating operation, the outdoor unit may emit water generated by the automatic defrosting
operation.
9
Before you call for or request servicing, troubleshoot a problem by performing following checks:
Symptom
Does not operate at all.
Diagnostic
–
 Is the timer operating?
6
Poor cooling or heating perfor-  Is the air filter dirty?
mance.
 Is the intake grill or outlet port of indoor unit blocked?
The unit operates differently
from the remote controller
setting.
See page
 Has the circuit breaker been turned off?
 Has there been a power outage?
 Has a fuse blown out or the circuit breaker been tripped?
10
–
 Is the room temperature adjusted appropriately?
4
 Is a window or door left opened?
 Is direct or strong sunlight shinning into the room in cooling operation?
 Are there other heating apparatus or computers operating, or too many people in the room in cooling operation?
–
 Is the fan speed set to “QUIET”?
When the fan speed setting is set to “QUIET”, noise reduction is prioritized and the air-conditioning
performance may become lower. If the volume of provided airflow is not agreeable to your preference, set the fan speed to “LOW” or higher fan speed.
5
 Has the OUTDOOR UNIT LOW NOISE mode been set?
5
 Do you have an arrangement with your electric company for Demand Response?
8
 Are the batteries used in the remote controller exhausted?
 Are the batteries used in the remote controller loaded properly?
2
Immediately stop operation and turn off the electrical breaker in following cases. Then consult authorized service personnel.
• The problem persists even if you perform these checks or diagnostics.
• The OPERATION indicator and TIMER indicator blink while the ECONOMY indicator is blinking fast.
NOTES:
• For any troubleshooting related to the wireless LAN control, refer to the setting manual for wireless LAN control or the mobile app installed in your
smartphone or tablet PC.
En-12
OPERATING MANUAL
9333003283_OM_EN.indd 12
1/20/2017 9:13:26 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement