Fujitsu ASTG22KMCB Operation Manual

Fujitsu ASTG22KMCB Operation Manual
PART No. 9382321000-02
SETTING MANUAL
Warning
This mark indicates procedures which, if improperly
performed, might lead to the death or serious injury
of the user.
Caution
This mark indicates procedures which, if improperly
performed, might possibly result in personal harm
to the user or damage to property.
This mark denotes an action that
is PROHIBITED.
This mark denotes an action that
is COMPULSORY.
Wireless LAN control for air conditioner
Warning
Before using this product, read these instructions thoroughly and keep this manual
for future reference.
Items to Check
* Prepare the following items before using this product.
Wireless Router
Smartphone or
Tablet PC
This product uses a wireless router that supports IEEE802.11b/g/n
wireless LAN standard. Set the connection to the wireless router with
WPS to perform communications by wireless LAN. Refer to the operation manual of the wireless router you wish to use, if it supports
IEEE802.11b/g/n or WPS.
Required OS version:
Android OS 4.1 or later
iOS 7.1 or later
 This product contains no user-serviceable parts. Always consult authorized
service personnel for repairing, installation, and relocation of this product.
Improper installation or handling will cause leakage, electric shock, or fire.
 In the event of a malfunction such as burning smell, immediately stop operation of the air conditioner, and disconnect all the power supply by turning off
the electrical breaker or disconnecting the power plug. Then consult authorized service personnel.
Do not repair, disassemble or remodel this product.
Do not get this product wet or use it in locations with lots of moisture.
Do not operate with wet hands.
Do not install this product in locations where the use of wireless equipment is
prohibited (e.g. hospitals).
 Do not use this product near persons with a pacemaker or similar devices.
 Do not use this product near automatic control equipment (e.g. automatic
doors and fire alarms).




Caution
Android and Google Play are registered trademarks of Google Inc.
App store is a service mark of Apple Inc., registered in the U.S. and other countries.
IOS is a trademark or registered trademark of Cisco in the U.S. and other countries
and is used under license.
For information on Wireless LAN (WLAN) control, please refer to the following web
site.
 Disconnect all the power supply when you are not using this product for extended periods.
 Do not stand on slippery, uneven or unstable surfaces when you operate the
unit.
 Do not press the buttons of this product any more strongly than is necessary.
2. USAGE PRECAUTIONS
Name of Parts
Wireless LAN indicator and
button on WLAN adapter
(for option)
LED 1 (green)
LED 2 (orange)
Setting button
 When you use this product, it will become possible to operate the air conditioner
Notice
* The wireless LAN label located beside the wireless LAN indicator is necessary for wireless LAN setup.
* Be sure to keep the wireless LAN label attached to the indoor unit by writing the details
down or pasting it on the list in the last section of this manual.
* The wireless LAN indicator and button is located either on the front panel or attached on
the outside of the indoor unit. If on the front panel, open the intake grille to access. (Refer
to the operating manual of the air conditioner.)
* The shape of the LED display and Setting button may differ from the illustration above
depending on the product.
 Be sure to check in advance that there are no malfunctions of the air conditioner.
in advance that you will be operating and stopping it from a distant location.
Sudden operation or stopping of the air conditioner may surprise a person and cause
the person to fall down or tumble if the person is on a stand. Furthermore, rapid changes in the outside temperature/room temperature may cause deterioration in a person’s
physical condition. Do not use this product when there are people in the room who are
not able to control the temperature by themselves (For example, infants, children, those
with physical disabilities, elderly or sick persons.).
 Fully understand the reserved timer settings and other operations before using
this product.
Unexpected operation or stopping of the air conditioner may cause deterioration in a
person’s physical condition or an adverse effect on animals or plants.
 Frequently check the settings and operating situation of the air conditioner when
using this product from a distant location.
Rapid changes in the outside temperature/room temperature may cause deterioration in
a person’s physical condition or an adverse effect on animals or plants.
 If you operate the air conditioner from this product, there will be no flashing of
the indicator lamps, nor any reception sounds from the air conditioner.
 If there is bad reception between this product and the wireless router, adjusting
1. SAFETY PRECAUTIONS
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and
operated keeping the radiator at least 20cm or more away from person’s body.
Notice
This device complies with Part 15 of FCC Rules and Industry Canada license-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of this device.
 Do not use this product in the following locations. Using this product in such
locations may cause communications becoming unstable or not possible.
 Near wireless communication equipment that uses the same frequency band (2.4GHz)
as this product.
static electricity or radio wave interference occurs.
(Radio waves may not reach depending on the environment.)
the wireless router position or direction of the antenna may improve the reception. It may also be possible to improve reception by moving the wireless router
closer to this product or using a wireless LAN repeater.
the use of radio waves regardless of whether you use encryption or not.
 Wireless LAN uses radio waves to exchange information between this product
 Do not connect to equipment and networks which you are not authorized to use
when setting up your wireless connection.
you use this product, and be sure to comply with the following safety precautions.
1
Open “Google Play” or “App Store” depending on the type of
your smartphone or tablet PC.
2
Search for “FGLair”.
3
Install the application software (mobile app) following the
instructions on your screen.
4.2. User registration
1
Open the installed mobile app.
2
Register the user (with either a smartphone or tablet PC) by
following the instructions in the create an account section of
the mobile app.
4.3. Air conditioner registration
Choose from the following modes to connect your air conditioner to your wireless router.
Note:
 Before starting this setting, wait for 60 seconds or more after the power supply is connected to the air conditioner (via breaker or plug).
 If both LED 1 and 2 are off, the WLAN adapter may be in Sleep mode. Be sure it is
deactivated before setting up the wireless LAN. (Refer to “5. SLEEP MODE”)
 Check that the smartphone or tablet PC is linked to the wireless router you are connecting the air conditioner. The setting will not work if it is not connected to the same wireless router.
 The display screen design may differ depending on the version of the mobile app.
 To control 2 or more air conditioners with the same smartphone or tablet PC, repeat the
setup of the chosen mode.
4.3.1 Button Mode
*Lighting pattern:
OFF
ON
Flashing
1
Launch the mobile app.
2
Sign in with your Email address and
password (as registered in “4.2.
User registration”) following the
screen on the mobile app.
 Initialize the settings of this product when disposing it, or transferring it to a third
party.
john@fgl.com

Sign in
3.3. Others
 Use this product as regular wireless LAN equipment.
 Do not use this product in hospitals or in/near locations with medical equipment.
3
 Do not use this product within aircraft.
Press the [+] button to add a new
air conditioner.
 Do not use this product near electronic equipment that handles high-precision control or
+
weak signals.
Examples of electronic equipment to be careful of:
Hearing aids, pacemakers, fire alarms, automatic doors and other automatic control
equipment
4
 This is not a guarantee of wireless connection and performance with all wireless
routers and in all residential environments. Radio waves may not reach or may
be interrupted in the following situations.
 Interference with wireless communication equipment using the same frequency
 Places where there are magnetic fields from equipment such as microwave ovens, or
 Install and setup this product only after reading the operating manual of the
wireless router.
Confirm that LED 2 is flashing. (On/
off at 2-second intervals.) Then select [Button mode] on the screen.
Button mode
Manual mode
If LED 1 and 2 are off, push the Setting button
once. (Refer to “5. SLEEP MODE”.)
 Use in buildings made from concrete, rebars or metal
 Installation near obstacles
static electricity or radio wave interference occurs
 To prevent personal injury, or property damage, read this section carefully before
4.1. Application software installation
3.2. Personal Information (Security-related) Usage Precautions
and the wireless router. This means it has the advantage of freely being able
to make a LAN connection if within reach of radio waves. On the other hand, if
the radio waves are within a certain range, they will reach all locations beyond
obstacles (e.g. walls). Therefore, it is possible your communications may be
intercepted and read or illegally intruded upon.
Objects may fall down causing personal injury, fire, or damage to property.
SSID: AC-UTY-          
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.
 Be sure to check on a regular basis that the power supply to the air conditioner is
securely connected, and that dust has not built up in the surrounding area.
It may cause heating, or fire.
4. PREPARATIONS FOR USE
Caution
 There is a possibility of interception if you use wireless LAN equipment due to
 If you know that there are people in the vicinity of the air conditioner, inform them
MAC:          
3.1. Radio Wave Usage Precautions
from locations where you cannot see it directly. This means that people in the
room may be exposed to the unintended operation of the air conditioner. Check
the condition of the room before using this product.
 Be sure that the airflow from the air conditioner will not cause any adverse effects.
Wireless LAN label
When you use a wireless LAN, there are precautions that you must follow in relation to radio waves, personal information, and so on. To use this product correctly,
be sure to read the following precautions and the operating manual of the wireless
LAN equipment you are using. We will assume no responsibility, unless legal liability is recognized, in regards to failures, other defects and damages incurred by use
of this product that occur through incorrect use or during use by yourself or a third
party.
 Places where there are magnetic fields from equipment such as microwave ovens, or
http://www.fujitsu-general.com/global/support/
Wireless LAN indicator and
button on front panel
(for built-in products)
3. WIRELESS LAN USAGE PRECAUTIONS
5
Press the WPS button on the wireless router that you are connecting
to.
(on/off=2sec/2sec)
Wireless router
Refer to the operating manual of the wireless
router for the location of the button and how to
press it.
 Incorrect operation due to failure to follow the instructions may cause harm or
damage, the seriousness of which is classified as follows:
Continues on the reverse side
9382321000-02_OM_EN_APS-12B.indd 1
2016/6/14 下午 05:18:43
6
7
Confirm that LED 2 is flashing.
(On/off at 2-second intervals.)
Then press and hold the Setting
button on the WLAN adapter for 3
seconds.
(on/off = 2sec/2sec)
LED 2 lighting will change.
8
(on/off: 2sec/2sec → 2sec/0.5sec)
(on/off=2sec/0.5sec)
Confirm that the LED 1 and 2 is
both on to proceed.
When [Connection complete] is
displayed, press [Done].
After returning to the [Wi-fi] screen,
wait a few seconds until the connected device changes from the A/C
to the wireless router.
Press [Return] to mobile app. or
close the screen and reactivate the
mobile app.
When the following screen appears,
select [continue].
 WLAN adapter updates will be displayed in the mobile app. Update the firmware
before use. Updates can be done according to the information on the screen.
Done
Connection complete
Home AP
 The air conditioner settings from the mobile app will not be reflected in the wire-
 State of the Wireless LAN indicators
*Lighting pattern:
OFF
ON
State of the Lamps
less remote controller.
 It will not be possible to give operation instructions or carry out monitoring from
All the lamps are off
the mobile app while the power supply is disconnected from the air conditioner
(via breaker or plug).
continue
LED1: On
LED2: 2sec/on
2sec/off
However, the displayed room temperature may not be correct depending on the
situation in the room, or the air conditioner operating status. Use this only as a
reference.
7
Press [Register] to start the connection with the wireless router.
 Push the Wireless LAN button, then
check if the LED lights.
 If the mobile app and remote controller settings differ, the latest operation per-
(2 times)
5. SLEEP MODE
*Lighting pattern:
Registration
Successful!
1~3
4
LED 2 is off or flashing fast
(Repeating 0.5 seconds on /
0.5 seconds off)
ON
To use the WLAN adapter
 Press the Setting button of the WLAN adapter. Confirm that the
See steps 1 to 3 in “4.3.1. Button mode”
LED lighting has changed.
Select [Manual mode].
6. INITIALIZATION (Reset)
Button mode
Manual mode
Note:
 Initialize this product if you are connecting to a wireless router different from the one
that is already connected.
 Initialize this product for the protection of your personal information when disposing it, or
transferring it to a third party.
 Be sure to unregister this product from your mobile app before initializing. For
how to unregister, please refer to the instructions on your mobile app.
[For Android]
Select the SSID of the air conditioner you are connecting to.
AC-UTY-xxxxxxxxxx
*Lighting pattern:
6
7
Select the SSID of the wireless router you are connecting to.
Input the wireless router (WLAN
access point) password then press
[Connect device].
LED 1 and 2 will both flash 2 times,
and a message will appear when
setup is complete.
Select the WLAN
Access Point
Home AP
XYZ AP
ABC123
Selected router
Enter
password

Connect device
Registration
Successful!
(2 times)
[For iOS]
5
6
LED1: On
LED2: 2sec/on
2sec/off
Mobile app
(Download and account registration)
Select [Open W-LAN setting] or
activate the wireless LAN by pressing the Home button -> [Setting] ->
[Wi-fi].
Select the SSID of the air conditioner you are connecting to.
Select the SSID of the wireless router you are connecting to.
Input the wireless router (WLAN
Access Point) password then press
[Connect device].
Open W-LAN setting
1
2
OFF
ON
Flashing
Press and hold the Setting button for 10 seconds.
Wireless LAN setup
and initial settings
Operations from the
mobile app
AC-UTY-xxxxxxxxxx
LED1: On
LED2: 2sec/on
2sec/off
* If you will continue to use this product after initialization, connect it to a wireless router following the procedures in “4. PREPARATIONS FOR USE”.
Home AP
XYZ AP
ABC123
Selected router
Enter
password
7. OPERATING TIPS

Connect device
Solutions
I don’t know how to
download the mobile
app.
Refer to “4.1. Application software installation”.
I am not able to use
the mobile app
Check that the version of the OS on your
mobile device is supported.
Refer to “Items to check”.
I have not received
the e-mail when registering my account
Set the domain permissions so that it is not
rejected as spam.
The method of
registering additional
users is unclear
You can only register 1 Email address
and password per WLAN adapter. Use
the same Email address and password for
other users to operate through the same
WLAN adapter.
The method of
registering additional
air conditioners is
unclear
To register additional air conditioners,
repeat the setup of the chosen mode in
“4.3. Air conditioner registration” for each
air conditioner.
Wireless LAN setup
is not possible
Check that your wireless router supports
“WPS function”. (Button mode)
Check if there was any previous owner using this wireless LAN control. If there was a
previous owner, please contact authorized
service personnel.
LED 1 will flash. (on/off=2sec/0.5sec)
After 60 seconds, the LED lamps will return to the
original lighting pattern. (LED1: on, LED 2: on/
off=2sec/2sec)
continue
Select the WLAN
Access Point
Situation
The initialization will be complete when all LED
lamps flashes 3 times simultaneously (on/off at
0.5-second intervals).
 For how to operate the mobile app, refer to the Operating manual of the mobile app.
 Check that the power to the wireless
router is on.
 Disconnect the power supply to the air
conditioner (via breaker or plug), and
then re-connect.
Check the following items before requesting repairs to this product.
Parts/Elements
 The power to the wireless router is not
on.
 There is a possibility that the WLAN
adapter is not properly connected to the
wireless router.
9. TROUBLESHOOTING
 The WLAN adapter will turn to Sleep mode when the WLAN
WLAN adapter will be nonfunctional, and both LED will be off.
Flashing
IEEE802.11b/g/n
Flashing
 The WLAN adapter cannot be used during Sleep mode. The
If LED 1 and 2 are off, push the Setting button
once. (Refer to “5. SLEEP MODE”.)
5
ON
setup is not completed within an hour after the power supply is
connected to the air conditioner (via breaker or plug).
4.3.2 Manual mode
OFF
Wireless LAN-compatible
standard
When the WLAN adapter is not used
(2 times)
*Lighting pattern:
OFF
 Refer to the Operating manual of the
mobile app.
Registration
Successful!
8. SPECIFICATIONS
LED 1 and 2 will both flash 2 times,
and a message will appear when
setup is complete.
 The LED lamps are turned off by setting
from the mobile app.
* If timer settings are done from the mobile app and from the wireless or wired remote controller, both timer settings will be active.
Register
 The power to the WLAN adapter is not
on.
 The WLAN adapter may be in Sleep
mode.
formed will take priority.
LED 1 and 2 will both flash 2 times,
and a message will appear when
setup is complete.
Causes and Solutions
 Check that the power to the air conditioner is on and that the air conditioner
breaker has not blown.
 The room temperature will be displayed in the mobile app during operation.
Open W-LAN setting
Flashing
Wireless LAN setup
is not possible (The
connection settings
of the WLAN adapter
and router are not
complete)
Check that your wireless router supports
“IEEE802.11b/g/n”. (Check with the operating manual of the wireless router.)
I am not able to
operate this product
from the mobile app
Check that the power to the indoor unit is
on.
Check that the WLAN adapter of the indoor
unit is on. (Check that the LED of your
WLAN adapter is lit or flashing.)
* If the LED is set to turn off in the mobile
app, it will not light up or flash.
Check that the power to the wireless router
is on.
LED 1 is flashing fast
(Repeating 0.5 seconds on /
0.5 seconds off)
All the lamps are flashing fast
(Repeating 0.5 seconds on /
0.5 seconds off)
 It is not possible to communicate with
the air conditioner.
 There may be a wiring error in the air
conditioner. Please contact authorized
service personnel.
 There is a problem with the WLAN
adapter.
 Disconnect the power supply to the air
conditioner (via breaker or plug), and
then re-connect. Setup the wireless
LAN again according to the procedures
in “4. PREPARATIONS FOR USE”.
If the problem persists even after you perform these checks or diagnostics, consult
authorized service personnel.
10. SETTING DETAILS
Record the setting details in the following table.
 Setting information
SSID
MAC address (MAC)
System commissioning date
 Installer contact details
Name
Telephone no.
Check that your smartphone is not in flight
mode.
Check that you are not in a place where it
is difficult to make a connection with radio
waves.
Check that the WLAN adapter is not in
Sleep mode.
 You can only register 1 Email address and password per WLAN adapter. To add
other users (smartphone or tablet PC) to the same WLAN adapter, please use
the same Email address and password.
9382321000-02_OM_EN_APS-12B.indd 2
2016/6/14 下午 05:18:44
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement