Fujitsu AUGG54LRLA-A Operation Manual

Fujitsu AUGG54LRLA-A Operation Manual
Cassette Type
OPERATING MANUAL
HƯỚNG DẪN VẬN HÀNH
BUKU PANDUAN PENGOPERASIAN
English
AIR CONDITIONER
ไทย
Indonesia
Việt
คูมือการใชงาน
KEEP THIS MANUAL FOR FUTURE REFERENCE
請保存本說明書以供日後參考
VUI LÒNG GIỮ LẠI SÁCH HƯỚNG DẪN NÀY ĐỂ THAM KHẢO TRONG TƯƠNG LAI
SIMPAN PANDUAN INI UNTUK REFERENSI MENDATANG
เก็บคูมือฉบับนี้ไวสําหรับใชอางอิงในภายหลัง
PART No. 9378589117-02
9378589117-02_OM.indb 1
8/6/2018 1:45:22 PM
OPERATING MANUAL
Cassette Type
PART No. 9378589117-02
CONTENTS
SAFETY PRECAUTIONS........................................ 1
FEATURES AND FUNCTIONS ............................... 2
NAME OF PARTS ................................................... 3
PREPARATORY OPERATION ................................ 5
OPERATION............................................................ 6
TIMER FUNCTIONS ............................................... 7
ON/OFF TIMER ....................................................... 7
WEEKLY TIMER ...................................................... 8
TEMPERATURE SET BACK TIMER ..................... 10
ADJUSTING THE DIRECTION OF AIR
CIRCULATION ........................................................11
SWING OPERATION .............................................11
ECONOMY OPERATION ...................................... 12
SENSOR SETTING ............................................... 12
CLEANING AND CARE ......................................... 13
TROUBLESHOOTING .......................................... 14
OPERATING TIPS................................................. 15
SELF-DIAGNOSIS ................................................ 17
SAFETY PRECAUTIONS
To prevent personal injury to others, or property damage, read this section carefully before you use this product, and be sure to comply
following safety precautions.
Incorrect operation due to failure to follow the instructions may cause harm or damage, the seriousness of which is classified as follows:
WARNING
CAUTION
This mark warns of death or serious injury.
This mark warns of injury or damage to property.
This mark denotes an action that is COMPULSORY.
This mark denotes an action that is PROHIBITED.
WARNING
• This product contains no user-serviceable parts. Always
consult authorized service personnel for repairing, installation, and relocation of this product.
Improper installation or handling will cause leakage,
electric shock, or fire.
• In the event of a malfunction such as burning smell,
immediately stop operation of the air conditioner, and
disconnect all the power supply by turning off the electrical breaker or disconnecting the power plug. Then
consult authorized service personnel.
• Take care not to damage the power supply cable.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
• In the event of refrigerant leakage, be sure to keep away
from fire or any flammables, and consult authorized
service personnel.
• If you see lightning or hear thunder, there might be a
lightning strike.
To prevent electric shock hazard, turn off the air conditioner by using the remote controller, and do not touch
this product or the power plug during thunderstorm.
• Do not install this product in area filled with mineral oil
such as a factory or area containing a large amount of
splashed oil or steam such as a kitchen.
• Do not start or stop the operation of this product by
inserting or pulling out the power plug, or by turning on
or off the circuit breaker.
• Do not use inflammable gases near this product.
• Do not expose yourself directly to the cooling airflow for
many hours.
• Do not insert your fingers or any other objects into outlet
port or inlet port.
• Do not operate with wet hands.
CAUTION
• Provide occasional ventilation during use.
• Always operate this product with air filters installed.
• Ensure that any electronic equipment is at least 1 meter
away from either this product.
• Turn off power source when not using this product for
extended periods.
• After long period of use, check whether the installation
stand does not deteriorate to prevent this product from
falling down.
• The airflow direction and the room temperature should
be carefully considered when you use this product in
a room with infants, children, elderly or sick persons.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
• Keep clean and tidy around the outdoor unit, and do not
place the things around it.
If it is covered with fallen leaves, there could be an infiltration of small animals or insects whose contact with the internal electrical components leads to the product malfunction.
• Do not direct the airflow at fireplaces or heating apparatus.
• Do not block or cover the inlet port and the outlet port.
• Do not apply any heavy pressure to radiator fins.
• Do not climb on, place objects on, or hang objects from
this product.
• Do not place vase or water container on this product.
• Do not place any other electrical products or household
belongings under this product.
• Dripping condensation from this product might get them
wet, and may cause damage or malfunction of your
property.
• Do not expose this product directly to water.
• Do not use this product for preservation of food, plants,
animals, precision equipment, art work, or other objects.
This may cause quality deterioration of those items.
• Do not expose animals or plants to the direct airflow.
• Do not drink the drainage from the air conditioner.
• Do not pull the power supply cable.
• Do not touch the aluminum fins of heat exchanger builtin this product to avoid personal injury when you install
or maintain the unit.
• Do not stand on unstable steps when operating or cleaning this product. It may overturn and can cause the injury.
En-1
9378589117-02_OM.indb Sec1:1
8/6/2018 1:45:23 PM
FEATURES AND FUNCTIONS
■ Energy saving and Comfortable function
■ Remote controller
INVERTER
WIRED REMOTE CONTROLLER
At the start of operation, large amount of power is used to
bring the room quickly to the desired temperature. Afterwards, the unit automatically switches to a low power setting for economic and comfortable operation.
The wired remote controller allows convenient control of
indoor unit operation.
ECONOMY OPERATION
The optional wireless remote controller can be used.When
you use remote controller, there are following different
points as compared with using wired remote controller.
When ECONOMY operation mode is operated, the room
temperature will be little higher than the set-temp under
cooling mode and lower than set-temp under heating
mode. Therefore, the ECONOMY mode is able to save
more energy than other normal mode.
SUPER QUIET OPERATION
When the FAN button is used to select QUIET, the indoor
unit begins super quiet operation; the indoor unit’s airflow
is reduced to produce quieter operation.
AUTO CHANGEOVER
WIRELESS REMOTE CONTROLLER (OPTION)
[ The additional function for wireless ones ]
• SLEEP timer
• TIMER
• 10°C HEAT operation
And you can use both wireless and wired remote controller simultaneously. (But function is limited.)
[ The restricted functions for wired ones ]
• Weekly timer
• Temperature set back timer
The operation mode (cooling, dry, heating) is switched automatically to maintain the set temperature, and the temperature is kept constant at all times.
■ Convenient function
WEEKLY TIMER
Use this timer function to set operating times for each day
of the week. Use the DAY OFF setting to switch off timed
operation for a selected day in the coming week. Because
all days can be set together, the weekly timer can be used
to repeat the timer settings for all of the days.
TEMPERATURE SET BACK TIMER
Use this timer function to change the set temperature in
the operation times set for each day of the week. This can
be used together with other timer settings.
En-2
9378589117-02_OM.indb Sec1:2
8/6/2018 1:45:23 PM
NAME OF PARTS
Indoor unit
1
2
3
4
5
6
7
Air filter (in air intake grille)
Airflow direction flaps
Air intake grille
Remote controller (wired)
Control panel (OPTION)
Remote control signal receiver
MANUAL AUTO button
When the MANUAL AUTO button
is pressed in for more than 10 seconds, the forced cooling operation
will start.
● The forced cooling operation is used
at the time of installation. Only for
authorized service personnel’s use.
● When the forced cooling operation
starts by any chance, press the
START/STOP button to stop the operation.
● Please press the button at Filter Reset.
●
2
1
5
3
4
8 OPERATION indicator lamp
(green)
9 TIMER indicator lamp (orange)
●
0 ECONOMY indicator lamp (green)
WIRED TYPE
●
5
0
TIMER indicator lamp lights when
the timer is set from wireless remote
controller.
(OPTION)
ECONOMY indicator lamp lights in
following operations:
• ECONOMY operation
• 10 °C HEAT operation (controlled by
wireless remote controller)
A Remote controller (wireless)
A
9
8
7
6
Either the wireless or wired remote controller can be selected.
En-3
9378589117-02_OM.indb Sec1:3
8/6/2018 1:45:23 PM
NAME OF PARTS
Remote controller
1
2
3
4
5
6
7
8
9
0
A
B
START/STOP button
SET TEMP. (temperature) button
MODE button
FAN button
ECONOMY button
TIMER MODE (CLOCK ADJUST) button
DAY (DAY OFF) button
SET BACK button
SET TIME ( < > ) button
TIMER DELETE button
TIMER SET button
Vertical airflow direction and
Swing button*1
C Horizontal airflow direction and
Swing button*2
D MAINTENANCE(FILTER RESET)
button#1
E Operation lamp
F Timer and Clock indicator
G Operation mode indicator
H Fan speed indicator
I Operation lock indicator
J Temperature indicator
K Function indicator
Defrost indicator
Thermo sensor indicator
ECONOMY indicator
Vertical swing indicator*3
Filter indicator#1
*1~3 These functions cannot be used.
(Please also see the operating manual of the
option when using it with options, etc.)
#1 Can be used if set correctly during
installation. Please consult authorized service
personnel when using this function.
En-4
9378589117-02_OM.indb Sec1:4
8/6/2018 1:45:23 PM
PREPARATORY OPERATION
Set the current day and time
1
2
Press the TIMER MODE (CLOCK
ADJUST) button for 2 seconds or
more. The time indicator on the
remote controller will flash.
3
Press the DAY button and select the current day.
A
appears around the selected day.
SU
MO
TU
WE
TH
FR
SA
Press the SET TIME (< >) buttons to set the current time.
Press repeatedly to adjust the current time in 1-minute increments. Press and hold to adjust the current time in 10-minute
increments.
SU MO TU WE TH FR SA
ex. Monday PM11:00
4
SET BACK
SU MO TU WE TH FR SA
Press the SET BACK button to switch between the
12- and 24-hour time displays.
SU MO TU WE TH FR SA
5
Press again to end.
En-5
9378589117-02_OM.indb Sec1:5
8/6/2018 1:45:23 PM
OPERATION
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
To start/stop operation
Press the START/STOP button.
Operation lamp
Air conditioner ON: Lit brightly
Air conditioner OFF: Not lit
To set the operation mode
●
Operation mode setting
Press the MODE button to set the operation mode.
If DRY is selected, the fan speed will be set to AUTO.
AUTO
●
Room temperature setting
Lower
●
Rise
Fan speed setting
COOL
DRY
FAN
HEAT*
Press the SET TEMP. buttons to set the room temperature.
Temperature setting range
AUTO ............................................... 18 to 30 °C
COOL/DRY ...................................... 18 to 30 °C
HEAT* .............................................. 16 to 30 °C
Press the FAN button to set the fan speed.
AUTO
HIGH
MED
LOW
QUIET
ECONOMY operation
Press the ECONOMY button to start or stop ECONOMY operation.
For details on the function, refer to page 12.
Child lock function
Press the DAY (DAY OFF) button and TIMER SET button
simultaneously for 2 seconds or more to activate the child lock
function and lock all of the buttons on the remote controller.
Press the buttons again for 2 seconds or more to deactivate
the child lock function.
When the child lock function is activated, the
mark appears. If any button is pressed during the child lock, the CL
indicator flashes.
En-6
9378589117-02_OM.indb Sec1:6
8/6/2018 1:45:24 PM
TIMER FUNCTIONS
OFF timer (See page 7.)
Use this timer function to stop air conditioner operation. The timer operates and air conditioner operation stops after the
set time has passed. The timer can be set up to 24 hours in advance.
ON timer (See page 7.)
Use this timer function to start air conditioner operation. The timer operates and air conditioner operation starts after the
set time has passed. The timer can be set up to 24 hours in advance.
WEEKLY timer (See page 8.)
Use this timer function to set operating times for each day of the week.
Use the DAY OFF setting to switch off timed operation for a selected day in the coming week.
Because all days can be set together, the weekly timer can be used to repeat the timer settings for all of the days.
Temperature SET BACK timer (See page 10.)
Use this timer function to change the set temperature in the operation times set for each day of the week.
This can be used together with other timer settings.
ON/OFF TIMER
To set the ON/OFF timer
1
Press the TIMER MODE button to
select the ON timer or OFF timer.
2
SU MO TU WE TH FR SA
From 1 to 24 hours
No indicator
NON
STOP
●
OFF
TIMER
ON
TIMER
WEEKLY
TIMER
ex. OFF timer set for 6 hours
Press the SET TIME (< >) buttons to set the time.
After the time is set, the timer will start automatically.
The amount of time until the OFF timer operates that is displayed
on the timer indicator decreases as time passes.
To cancel
• Press the TIMER DELETE button to cancel the timer mode.
• The timer mode can also be canceled by changing the timer mode using the TIMER MODE button.
En-7
9378589117-02_OM.indb Sec1:7
8/6/2018 1:45:24 PM
WEEKLY TIMER
Weekly timer setting
1
2
Press the TIMER SET button for
2 seconds or more.
Press the TIMER MODE button to select the weekly timer.
3
●
Day of the week setting
ALL
SU
MO
TU
WE
TH
FR
SA
2
1
Press the DAY button to select the day of the week, and then press the TIMER
SET button to confirm the setting.
For ALL, all of the days can be set together when a
appears around
each day.
4
●
Time setting
When the operating time is set,
the
mark appears.
ON-1
3
2
1
OFF-1
ON-2
OFF-2
ex. The timer is set for 7:00-18:00.
Press the SET TIME (< >) buttons to set the time, and then press the TIMER SET
button to confirm the setting and proceed to the next ON or OFF time setting.
Up to 2 times ON and OFF times can be set per day.
Press the DAY button to complete the time setting and return to the day of the week
setting.
5
●
To delete the operating time
If the TIMER DELETE button is pressed dur-
3 4
ing steps or , the operating time for the
selected day will be deleted.
If all the days are selected, the operating
times for all of the days will be deleted.
3
4
Repeat steps and .
To complete the weekly timer settings, press the TIMER
SET button for 2 seconds or more.
NOTES
• The operating time can be set in 30-minute increments only.
• The OFF time can be carried over to the next day.
• The ON timer and the OFF timer functions cannot be set using the weekly timer. Both an ON and OFF time must be set.
En-8
9378589117-02_OM.indb Sec1:8
8/6/2018 1:45:24 PM
WEEKLY TIMER
WEEKLY timer operation
●
To start
●
When the weekly timer is selected, the
timer starts automatically.
To cancel
• Press the TIMER DELETE button to
cancel the timer mode.
• The timer mode can also be
canceled by changing the timer
mode using the TIMER MODE
button.
ex. Operating time 7:00-18:00
The operating time for the current day
is displayed.
To set the DAY OFF (for a holiday)
1
2
3
4
During the weekly timer, press
the TIMER SET button for 2
seconds or more to set the
day.
Select the day to set the DAY
OFF.
Press the DAY (DAY OFF)
button for 2 seconds or more
to set the DAY OFF.
Press the TIMER SET button
for 2 seconds or more to complete the DAY OFF setting.
SU MO TU WE TH FR SA
SU MO TU WE TH FR SA
The
mark flashes under a day of the week.
●
3 6 9 12 15 18 21
3 6 9 12 15 18 21
ex. The DAY OFF is set for Monday.
To cancel
Follow the same procedures as those
for setup.
NOTES
• The DAY OFF setting is only available for days for which weekly settings already exist.
• If the operating time carries over to the next day (during a next day setting), the effective DAY OFF range will be set as shown
below.
●
Normal
●
Next day setting
DAY OFF
ON
OFF
WEEKLY
Preceding day
ON
DAY OFF
OFF
ON
WEEKLY
OFF
WEEKLY
Setting day
Next day
Preceding day
OFF
ON
WEEKLY
Setting day
Next day
• The DAY OFF setting can only be set 1 time. The DAY OFF setting is cancelled automatically after the set day has passed.
En-9
9378589117-02_OM.indb Sec1:9
8/6/2018 1:45:24 PM
TEMPERATURE SET BACK TIMER
Temperature SET BACK timer setting
1
SET BACK
2
If there is no existing
SET BACK temperature setting, “- -” will
be displayed for the
temperature.
Press the TIMER SET button
for 2 seconds or more.
Press the SET BACK button to change to the SET BACK confirmation display.
The SET BACK operating time and the set temperature will be
displayed.
3
●
Day setting
1
●
Operating time setting
2
4
3
ex. When setting all days together
Follow the same procedures to set the operating time as those for the weekly timer. The TIMER DELETE button is also used
as described in the procedures for the weekly timer.
4
●
Temperature setting
Press the SET TEMP. buttons to set the
temperature. (The temperature setting range
is the same as the range for the operation
mode.)
5
3
ex. Operating time 15:00–22:00
ON
SET BACK temperature
Normal temperature
28°C
24°C
4
Repeat steps and .
Press the TIMER SET button for
2 seconds or more to complete
the temperature SET BACK timer
settings.
OFF
24°C
Temperature SET BACK timer operation
●
To start
●
To cancel
SET BACK
1
ex. Display during SET BACK timer operation
(The operating time will not be displayed.)
Press the SET BACK button. The SET BACK confirmation display appears for
5 seconds, and then the timer starts automatically.
2
Press the SET BACK button, and then
press the TIMER DELETE button while
the SET BACK confirmation display is
displayed. Even if the SET BACK button
is pressed again, the SET BACK timer
will be cancelled.
NOTES
•
•
•
•
The SET BACK timer only changes the set temperature, it cannot be used to start or stop air conditioner operation.
The SET BACK timer can be set to operate up to 2 times per day but only 1 temperature setting can be used.
The SET BACK timer can be used together with the ON, OFF, and weekly timer functions.
The SET BACK operating time is displayed only in the SET BACK confirmation display. (Refer to step 1 for the SET BACK
confirmation display.)
En-10
9378589117-02_OM.indb Sec1:10
8/6/2018 1:45:24 PM
ADJUSTING THE DIRECTION OF AIR CIRCULATION
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
Start air conditioner operation before performing this procedure.
To set the operation mode
●
Vertical air direction adjustment
Press the START/STOP button to start the air conditioner, and then proceed as follows.
Press the vertical airflow direction and swing button to adjust the direction of
the vertical airflow.
Each time the button is pressed, the air direction range will change as follows:
1
2
3
4
The remote controller display does not change.
● Attempting to move up/down air di-
rection flaps manually could result in
improper operation; in this case, stop
operation and restart. The louvers
should begin to operate properly
again.
Recommended airflow direction setting:
1, 2, 3, 4: During cooling/dry mode
2, 3, 4
: During heating mode
● When used in a room with infants,
children, elderly or sick persons, the
air direction and room temperature
should be considered carefully when
making settings.
●
The vertical airflow direction is set automatically as shown, in accordance with the
type of operation selected.
During cooling/dry mode
: Horizontal flow 1
During heating mode*
: Downward flow 4
●
During AUTO mode operation, for the first minute after beginning operation, airflow
will be horizontal 1; the air direction cannot be adjusted during this period.
●
Horizontal air direction adjustment.
The function cannot be used.
SWING OPERATION
Begin air conditioner operation before performing this procedure.
To select/stop swing operation
Press the vertical airflow direction and swing button for more than 2 seconds.
(Stop the setting by pressing for more than 2 seconds again.)
About Swing Operation
The type of operation
Cooling/Heating/Dry/Fan
Range of swing
1 to 4
●
The swing operation may stop temporarily when the air conditioner’s fan is not operating, or when operating at very low
speeds.
En-11
9378589117-02_OM.indb Sec1:11
8/6/2018 1:45:24 PM
ECONOMY OPERATION
Begin air conditioner operation before performing this procedure.
To Use the ECONOMY Operation
Press the ECONOMY button.
The ECONOMY indicator will light.
ECONOMY operation begins.
To Stop the ECONOMY Operation
Press the ECONOMY button again.
The ECONOMY indicator will go out.
Normal operation begins.
About ECONOMY Operation
At the maximum output, ECONOMY operation is approximately 70% of normal air conditioner operation for cooling and heating.
● If the room is not cooled (or heated) well during ECONOMY operation, select normal operation.
●
During the monitor period in the AUTO mode, the air conditioner operation will not change to ECONOMY operation even if
ECONOMY operation is selected by pressing the ECONOMY operation button.
●
When ECONOMY operation mode is operated, the room temperature will be little higher than the set-temp under cooling mode
and lower than set-temp under heating mode. Therefore, the ECONOMY mode is able to save more energy than other normal
mode.
SENSOR SETTING
Room temperature sensor selection
•
This function is locked at the factory. In order to detect the room temperature correctly, consult authorized service personnel when using this function.
Indoor unit
Press the ECONOMY button for more than 2 seconds to select
whether the room temperature is detected at the indoor unit or
the remote controller.
When the
thermo sensor indicator appears, the room
temperature is detected at the remote controller.
NOTES
•
If this function is locked, the location where the room temperature is detected cannot be changed and the
when the ECONOMY button is pushed for 2 seconds or more.
mark flashes
En-12
9378589117-02_OM.indb Sec1:12
8/6/2018 1:45:24 PM
CLEANING AND CARE
CAUTION
●
Before cleaning the unit, be sure to stop the unit and disconnect the power supply.
●
Turn off the electrical breaker.
●
A fan operates at high speed inside the unit, and personal injury could result.
●
Be careful not to drop the intake grille.
●
As the filter cleaning involves high-altitude operation, please consult the professional technical service personnel.
●
When used for extended periods, the unit may accumulate dirt inside, reducing its performance. We recommend that the unit
be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized service personnel.
●
When cleaning the unit’s body, do not use water hotter than 40°C, harsh abrasive cleansers, or volatile agents like benzene or
thinner.
●
Do not expose the unit body to liquid insecticides or hair sprays.
●
If the unit will not be operated for a period of 1 month or more, be sure to allow the inner parts of the unit to dry thoroughly, in
advance, by operating the unit in fan mode for half a day.
Cleaning the Air Filter
1. Push the intake grille’s hooks inward towards the center of the unit to open the
intake grille.
4. Re-attach the air filters to the intake grille.
1 Replace the air filter into its holder.
2 Make sure that the air filter makes contact with the filter
stopper when it is replaced into its holder.
2. Pull out the filter from the intake grille.
5. Close the intake grille and push the intake
grille’s hooks outward.
3. Clean the air filter.
Remove the dust from the air filters by vacuuming or washing
them. After washing, allow the air filters to dry thoroughly in
an area protected from sunlight.
●
Dust can be cleaned from the air filter either with a vacuum
cleaner, or by washing the filter in a solution of mild detergent and warm water. If you wash the filter, be sure to allow
it to dry thoroughly in a shady place before reinstalling.
●
If dirt is allowed to accumulate on the air filter, air flow will
be reduced, lowering operating efficiency and increasing
noise.
Filter indicator Reset (A special setting)
● Can
tion.
be used if set correctly during installation. Please consult authorized service personnel when using this func-
• It lights on when it is time to clean the air filters.
After turning the power on.
Press the MAINTENANCE button for
2 seconds or more on the remote control.
The filter indicator will disappear.
En-13
9378589117-02_OM.indb Sec1:13
8/6/2018 1:45:25 PM
TROUBLESHOOTING
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
WARNING
●
In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the electrical breaker, and consult authorized service personnel.
●
Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. Always be sure to turn
off the electrical breaker to ensure that power is completely off.
Before requesting service, perform the following checks:
Symptom
NORMAL
FUNCTION
Does not operate immediately:
Noise is heard:
Problem
See Page
If the unit is stopped and then immediately started again, the compressor will not operate for about 3 minutes, in order to prevent
fuse blowouts.
● Whenever the electrical breaker is turned off then on again, the
protection circuit will operate for about 3 minutes, preventing unit
operation during that period.
—
During operation and immediately after stopping the unit, the sound
of water flowing in the air conditioner’s piping may be heard. Also,
noise may be particularly noticeable for about 2 to 3 minutes after
starting operation (sound of coolant flowing).
—
●
●
*● During heating operation, a sizzling sound may be heard
occasionally. This sound is produced by the automatic defrosting
operation.
15
Smells:
●
Some smell may be emitted from the indoor unit. This smell is the
result of room smells (furniture, tobacco, etc.) which have been
taken into the air conditioner.
—
Mist or steam are emitted:
●
During cooling or dry operation, a thin mist may be seen emitted
from the indoor unit. This results from the sudden cooling of room air
by the air emitted from the air conditioner, resulting in condensation
and misting.
—
*● During heating operation, the outdoor unit’s fan may stop, and
steam may be seen rising from the unit. This is due to the automatic
defrosting operation.
15
*● When heating operation is started, fan speed is temporarily very low,
to allow internal parts to warm up.
*● During heating operation, if the room temperature rises above the
thermostat setting, the outdoor unit will stop, and the indoor unit will
operate at very low fan speed. If you wish to warm the room further,
set the thermostat to a higher setting.
—
*● During heating operation, the unit will temporarily stop operation
(between 4 and 15 minutes) as the automatic defrosting mode operates. During the automatic defrosting operation,
will be shown
on the remote controller display.
15
●
The fan may operate at very low speed during dry operation or when
the unit is monitoring the room’s temperature.
—
●
During QUIET operation, the fan will operate at very low speed.
—
●
In the monitor AUTO operation, the fan will operate at very low speed.
—
*● During heating operation, water may be produced from the outdoor
unit due to the automatic defrosting operation.
15
Airflow is weak or stops:
Water is produced from the
outdoor unit:
The FILTER indicator blinks:
thermo sensor display
on the remote controller is
flashing:
●
Clean the filter. Afterwards, turn the FILTER indicator off.
13
●
The room temperature sensor may be malfunctioning. Please consult authorized service personnel.
—
En-14
9378589117-02_OM.indb Sec1:14
8/6/2018 1:45:25 PM
TROUBLESHOOTING
Symptom
CHECK
ONCE
MORE
Does not operate at all:
Poor cooling (or heating*)
performance:
Problem
●
●
●
Has the circuit breaker been turned off?
Has there been a power failure?
Has a fuse blown out, or a circuit breaker been tripped?
●
Is the timer operating?
●
Is the air filter dirty?
●
Are the air conditioner’s intake grille or outlet port blocked?
●
Did you adjust the room temperature settings (thermostat) correctly?
●
Is there a window or door open?
●
In the case of cooling operation, is a window allowing bright sunlight to enter? (Close the curtains.)
●
In the case of cooling operation, are there heating apparatus and
computers inside the room, or are there too many people in the
room?
●
Is the unit set for QUIET operation?
See Page
—
7 to 10
—
—
If the problem persists after performing these checks, or if you notice burning smells, stop operation immediately, turn off electric
breaker, and consult with authorized service personnel.
OPERATING TIPS
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
Heating Performance*
●
●
This air conditioner operates on the heat-pump principle,
absorbing heat from outdoor air and transferring that heat
indoors. As a result, the operating performance is reduced
as outdoor air temperature drops. If you feel that insufficient
heating performance is being produced, we recommend you
use this air conditioner in conjunction with another type of
heating appliance.
Heat-pump air conditioners heat your entire room by recirculating air throughout the room, with the result that some time
may be required after first starting the air conditioner until the
room is heated.
When Indoor and Outdoor Temperature
are High*
When both indoor and outdoor temperatures are high during use
of the heating mode, the outdoor unit’s fan may stop at times.
Low Ambient Cooling
When the outdoor temperature drops, the outdoor unit’s fans may
switch to Low Speed, or one of the fans may stop intermittently.
Fan speed: AUTO
Heating*:
The fan will operate at very low speed when the
temperature of the air issued from the indoor unit is
low.
Cooling:
As the room temperature approaches that of the set
temperature, the fan speed becomes slower.
Fan:
The fan runs at the low fan speed.
Microcomputer-controlled Automatic
Defrosting*
●
When using the heating mode under conditions of low outdoor
temperature and high humidity, frost may form on the outdoor
unit, resulting in reduced operating performance.
In order to prevent this kind of reduced performance, this
unit is equipped with a microcomputer-controlled automatic
defrosting function. During the defrost cycle, the indoor fan will
shutdown and
will be displayed on the remote controller. It will take anywhere from 4 to 15 minutes before the air
conditioner starts up again.
●
After heating operation stops, if frost forms on the outdoor
unit, the unit will start Automatic Defrosting operation.
At this time, the outdoor unit will automatically stop after
operating for a few minutes.
Dual Remote Controllers (optional)
An additional remote controller can be added up to the
maximum of 2 remote controllers. Either remote controller
can control the air conditioner. However, the timer functions
cannot be used at the secondary unit.
Group Control
1 remote controller can control up to 16 air conditioners. All of
the air conditioners will be operated with the same settings.
Hot Start*
The indoor unit prevents cold drafts when heating operation
begins.
The indoor unit fan will not operate or it will operate at a
very low speed until the heat exchanger reaches the set
temperature.
En-15
9378589117-02_OM.indb Sec1:15
8/6/2018 1:45:25 PM
OPERATING TIPS
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
Mode Operation
AUTO (in COOLING model):
●
When AUTO (automatic changeover) operation first selected, the fan will operate at very low speed for about a few
minutes, during which time the indoor unit detects the room conditions and selects the proper mode.
Room temperature is higher than the defined temperature in temperature
setting  Cooling mode or dry mode
Room temperature is close to or lower than the defined temperature in
temperature setting  Monitor operation
Cooling mode
or Dry mode
Defined
temperature in
temperature
setting
Monitor operation
●
When the indoor unit has adjusted your room’s temperature to near the temperature setting, it will begin monitor operation. In the monitor operation mode, the fan will operate at low speed. If the room temperature subsequently changes,
the indoor unit will once again select the appropriate operation (cooling) to adjust the temperature to the value set in the
temperature setting.
●
If the mode automatically selected by the unit is not what you wish, select one of the mode operation (COOL, DRY, FAN).
AUTO [in HEAT & COOL (Reverse Cycle) model]:
●
When AUTO (automatic changeover) is selected, the air conditioner selects the appropriate operation mode (cooling or
heating) according to your room’s present temperature.
●
When AUTO (automatic changeover) operation first selected, the fan will operate at low speed for about a few minute,
during which time the indoor unit detects the room conditions and selects the proper operation mode.
Room temperature is higher than the defined temperature in temperature
setting → Cooling mode or dry mode
Room temperature is close to the defined temperature in temperature setting
→ Determined by outdoor temperature
Room temperature is lower than the defined temperature in temperature
setting → Heating mode
Cooling or Dry
Defined
temperature in
temperature
setting
Determined by
outdoor temperature
Heating
●
When the air conditioner has adjusted your room’s temperature to near the thermostat setting, it will begin monitor operation. In the monitor operation mode, the fan will operate at low speed. If the room temperature subsequently changes,
the air conditioner will once again select the appropriate operation (heating, cooling) to adjust the temperature to the
value set in the thermostat.
●
If the mode automatically selected by the unit is not what you wish, select one of the mode operation (HEAT, COOL, DRY, FAN).
HEAT *: ● Use to warm your room.
● When heating mode is selected, the air conditioner will operate at very
low fan speed for about 3 to 5 minutes, after which it will switch to the
selected fan setting. This period of time is provided to allow the indoor
unit to warm up before beginning full operation.
● When the room temperature is very low, frost may form on the outdoor
unit, and its performance may be reduced. In order to remove such frost,
the unit will automatically enter the defrost cycle from time to time. During
automatic defrosting operation, the heat operation will be interrupted.
● After the start of heating operation, it takes sometime before the room
gets warmer.
COOL: ● Use to cool your room.
● Use for gently cooling while dehumidifying your room.
DRY:
● You cannot heat the room during dry mode.
● During dry mode, the unit will operate at low speed; in order to adjust
room humidity, the indoor unit’s fan may stop from time to time. Also, the
fan may operate at very low speed when adjusting room humidity.
● The fan speed cannot be changed manually when dry mode has been
selected.
● Use to circulate the air throughout your room.
FAN:
During heating mode:
Set the thermostat to a temperature setting
that is higher than the current room temperature. The heating mode will not operate if the thermostat is set lower than the
actual room temperature.
During cooling/dry mode:
Set the thermostat to a temperature setting
that is lower than the current room temperature. The cooling and dry modes will
not operate if the thermostat is set higher
than the actual room temperature (in cooling mode, the fan alone will operate).
During fan mode:
You can not use the unit to heat and cool
your room.
En-16
9378589117-02_OM.indb Sec1:16
8/6/2018 1:45:25 PM
OPERATING TIPS
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
AUTO Restart
In Event of Power Interruption
●
Should the power supply to the air conditioner be interrupted
by a power failure, the air conditioner will restart automatically
in the previously selected mode once the power is restored.
●
Use of other electrical appliances (electric shaver, etc.) or
nearby use of a wireless radio transmitter may cause the air
conditioner to malfunction. In this event, temporarily disconnect the power supply, reconnect it, and then use the remote
controller to resume operation.
Notices
*● During use of the heating mode, the outdoor unit will occasionally commence the defrost operation for brief periods.
During the defrosting operation, if the user sets the indoor
unit for heating again, the defrosting mode will continue, and
the heating operation will begin after completion of defrosting, with the result that some time may be required before
warm air is emitted.
*● During use of the heating mode, the top of the indoor unit
may become warm, but this is due to the fact that coolant is
circulated through the indoor unit even when it is stopped;
it is not a malfunction.
SELF-DIAGNOSIS
When “Er” in temperature indicator is displayed, inspection of the air conditioning system is necessary. Please consult
authorized service personnel.
Unit number (usually “00”)
Error code
ex. Self-diagnosis check
En-17
9378589117-02_OM.indb Sec1:17
8/6/2018 1:45:25 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement