Fujitsu AUUB24TLAV1 Installation Manual

Fujitsu AUUB24TLAV1 Installation Manual
For authorized service personnel only.
MANUEL D’INSTALLATION
UNITÉ INTÉRIEURE (type cassette)
Pour le personnel agréé uniquement.
MANUAL DE INSTALACIÓN
UNIDAD INTERIOR (Tipo casete)
AUUB18TLAV1
AUUB24TLAV1
AUUB30TLAV1
Únicamente para personal de servicio autorizado.
Français
INDOOR UNIT (Cassette Type)
Español
INSTALLATION MANUAL
English
TM
AUUB36TLAV1
AUUB48TLAV1
PART No. 9371022574-02
9371022574-02_IM.indb 1
2018/1/26 10:21:59
INSTALLATION MANUAL
1.2. SPECIAL PRECAUTIONS
PART No. 9371022574-02
VRF system indoor unit (Cassette type)
When Wiring
Contents
1.
SAFETY PRECAUTIONS .........................................................................................1
1.1. IMPORTANT! Please read before starting .........................................................1
1.2. SPECIAL PRECAUTIONS .................................................................................1
2.
ABOUT THIS PRODUCT..........................................................................................2
2.1. Precautions for using R410A refrigerant ............................................................2
2.2. Special tools for R410A ......................................................................................2
2.3. Accessories ........................................................................................................2
2.4. Optional parts .....................................................................................................2
2.5. About unit of the length ......................................................................................2
3.
INSTALLATION WORK ............................................................................................3
3.1. Selecting an installation location ........................................................................3
3.2. Installation dimension .........................................................................................3
3.3. Installing the unit ................................................................................................3
4.
PIPE INSTALLATION ...............................................................................................4
4.1. Selecting the pipe material .................................................................................4
4.2. Pipe requirement ................................................................................................4
4.3. Flare connection (pipe connection) ....................................................................4
4.4. Installing heat insulation .....................................................................................5
ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL INJURY OR DEATH. ONLY A
QUALIFIED, EXPERIENCED ELECTRICIAN SHOULD ATTEMPT TO WIRE THIS SYSTEM.
• Do not supply power to the unit until all wiring and tubing are completed or reconnected
and checked.
• Highly dangerous electrical voltages are used in this system. Carefully refer to the wiring diagram and these instructions when wiring. Improper connections and inadequate
earthing (grounding) can cause accidental injury or death.
• Earth (Ground) the unit following local electrical codes.
• Connect all wiring tightly. Loose wiring may cause overheating at connection points and
a possible fire hazard.
When Transporting
Be careful when picking up and moving the indoor and outdoor units. Get a partner to
help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin
aluminum fins on the air conditioner can cut your fingers.
When Installing...
...In a Ceiling or Wall
Make sure the ceiling/wall is strong enough to hold the unit’s weight. It may be necessary
to construct a strong wood or metal frame to provide added support.
...In a Room
Properly insulate any tubing run inside a room to prevent “sweating” that can cause
dripping and water damage to walls and floors.
5.
INSTALLING DRAIN PIPES .....................................................................................5
6.
ELECTRICAL WIRING .............................................................................................6
6.1. Electrical requirement.........................................................................................6
6.2. Wiring method ....................................................................................................7
6.3. Unit wiring...........................................................................................................7
6.4. Connection of wiring ...........................................................................................8
6.5. Optional parts wiring...........................................................................................9
6.6. External input and external output (Optional parts) ............................................9
When Connecting Refrigerant Tubing
FIELD SETTING .......................................................................................................10
7.1. Setting the address ............................................................................................11
7.2. Custom code setting...........................................................................................11
7.3. Function setting ..................................................................................................11
• Keep all tubing runs as short as possible.
• Use the flare method for connecting tubing.
• Apply refrigerant lubricant to the matching surfaces of the flare and union tubes before
connecting them, then tighten the nut with a torque wrench for a leak-free connection.
• Check carefully for leaks before opening the refrigerant valves.
7.
8.
CASSETTE GRILLE INSTALLATION .......................................................................12
9.
TEST RUN ................................................................................................................12
9.1. Test run using Outdoor unit (PCB) .....................................................................12
9.2. Test run using remote controller .........................................................................12
10. CHECK LIST.............................................................................................................12
11. ERROR CODES .......................................................................................................13
...In an Area with High Winds
Securely anchor the outdoor unit down with bolts and a metal frame.
Provide a suitable air baffle.
...In a Snowy Area (for Heat Pump-type Systems)
Install the outdoor unit on a raised platform that is higher than drifting snow.
When Servicing
• Turn the power OFF at the main circuit breaker panel before opening the unit to check or
repair electrical parts and wiring.
• Keep your fingers and clothing away from any moving parts.
• Clean up the site after you finish, remembering to check that no metal scraps or bits of
wiring have been left inside the unit being serviced.
• After installation, explain correct operation to the customer, using the operating manual.
DANGER
Never touch electrical components immediately after the power supply has been turned
off. Electrical shock may occur. After turning off the power, always wait 5 minutes or more
before touching electrical components.
1. SAFETY PRECAUTIONS
1.1. IMPORTANT! Please read before starting
This air conditioning system meets strict safety and operating standards.
As the installer or service person, it is an important part of your job to install or service the
system so it operates safely and efficiently.
For safe installation and trouble-free operation, you must:
• Carefully read this instruction booklet before beginning.
• Follow each installation or repair step exactly as shown.
• Observe all local, state, and national electrical codes.
• Pay close attention to all danger, warning, and caution notices given in this manual.
WARNING:
This symbol refers to a hazard or unsafe practice which can result in
severe personal injury or death.
CAUTION:
This symbol refers to a hazard or unsafe practice which can result in
personal injury and the potential for product or property damage.
• Hazard alerting symbols
: Electrical
WARNING
Request your dealer or a professional installer to install the unit in accordance with this
Manual.
An improperly installed unit can cause serious accidents such as water leakage, electric
shock, or fire.
If the unit is instruction in disregard of the instructions in the Installation Manual, it will
void the manufacturer’s warranty.
Do not turn ON the power until all work has been completed.
Turning ON the power before the work is completed can cause serious accidents such
as electric shock or fire.
If refrigerant leaks while work is being carried out, ventilate the area.
If the refrigerant comes in contact with a flame, it produces a toxic gas.
: Safety/alert
If Necessary, Get Help
These instructions are all you need for most installation sites and maintenance conditions.
If you require help for a special problem, contact our sales/service outlet or your certified
dealer for additional instructions.
In Case of Improper Installation
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information
pertaining to your safety. Be sure to observe them.
• Hand this Manual, together with the Operating Manual to the customer.
• Request the customer to keep them on hand for future use, such as for relocating or
repairing the unit.
The manufacturer shall in no way be responsible for improper installation or maintenance
service, including failure to follow the instructions in this document.
Installation must be performed in accordance with the requirement of NEC (National
Electrical Code) and CEC (Canadian Electrical Code) by authorized personnel only.
Except for EMERGENCY, never turn off main as well as sub breaker of the indoor units
during operation. It will cause compressor failure as well as water leakage. First, stop
the indoor unit by operating the control unit, converter or external input device and then
cut the breaker.
Make sure to operate through the control unit, converter or external input device.
When the breaker is designed, locate it at a place where the users cannot start and stop
in the daily work.
En-1
9371022574-02_IM.indb 1
2018/1/26 10:21:59
For installing indoor unit.
Template
(Carton top)
2. ABOUT THIS PRODUCT
1
2.1. Precautions for using R410A refrigerant
Washer
For installing indoor unit.
WARNING
8
Do not introduce any substance other than the prescribed refrigerant into the refrigeration cycle.
If air enters the refrigeration cycle, the pressure in the refrigeration cycle will become
abnormally high and cause the piping to rupture.
Insulation
If there is a refrigerant leakage, make sure that it does not exceed the concentration
limit.
If a refrigerant leakage exceeds the concentration limit, it can lead to accidents such as
oxygen starvation.
Drain hose
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
area. Touching the refrigerant directly can cause frostbite.
For installing drain pipe
1
1
Hose band
For installing drain hose.
If a refrigerant leakage occurs during operation, immediately vacate the premises and
thoroughly ventilate the area.
If the refrigerant comes in contact with a flame, it produces a toxic gas.
2.2. Special tools for R410A
1
For installing drain pipe.
Drain pipe insulation
1
WARNING
To install a unit that uses R410A refrigerant, use dedicated tools and piping materials that have been manufactured specifically for R410A use. Because the pressure
of R410A refrigerant is approximately 1.6 times higher than the R22, failure to use
dedicated piping material or improper installation can cause rupture or injury.
Furthermore, it can cause serious accidents such as water leakage, electric shock, or
fire.
Tool name
For installing drain pipe.
(Ø 3/4 in [I.D.]; Ø 1-1/16 in [O.D.])
2.4. Optional parts
Description
Contents of change for R22 tool
Gauge manifold
Pressure is huge and cannot be measured with a conventional
(R22) gauge. To prevent erroneous mixing of other refrigerants,
the diameter of each port has been changed.
It is recommended to use a gauge manifold with a high pressure
display range 30 in Hg to 768 psi (–0.1 to 5.3 MPa) and a low
pressure display range 30 in Hg to 551 psi (–0.1 to 3.8 MPa).
Charging hose
To increase pressure resistance, the hose material and base size
were changed.
Vacuum pump
A conventional (R22) vacuum pump can be used by installing a
vacuum pump adapter.
• A conventional vacuum pump can be used by installing a
vacuum pump adapter.
• Be sure that the pump oil does not back flow into the system.
Use one capable for vacuum suction of 5 Torr, –755 mm Hg
(–100.7 kPa).
Gas leakage
detector
Special gas leakage detector for HFC refrigerant R410A.
Model
UTY-XWZXZC
UTY-XWZXZB
For control input function.
(Apply voltage terminal / CNA01)
External connect kit UTY-XWZXZD
WARNING
The following installation parts are furnished. Use them as required.
Keep the Installation Manual in a safe place and do not discard any other accessories
until the installation work has been completed.
For control input function.
(Dry contact terminal / CNA02)
UTY-XWZXZ7
For forced thermostat off function.
(Apply voltage terminal / CNA03)
UTY-XWZXZE
For forced thermostat off function.
(Dry contact terminal / CNA04)
IR receiver kit
UTY-LBHXD
For air conditioner operation.
Human sensor kit
UTY-SHZXC
To prevent waste of electricity, this
function controls the temperature
setting when no one is occupying the
room.
Wide panel
UTG-AKXA-W
Wide panel hides the gap between the
ceiling hole and the Cassette grille.
Panel spacer
UTG-BKXA-W
Installation in a space of 1-9/16 in (56
mm) or greater is possible by using
panel spacer when the height behind
the ceiling is low.
Air outlet shutter
plate
UTR-YDZK
Install the plate at outlet when carrying
out 3-way direction operation.
2.3. Accessories
For installation purposes, be sure to use the parts supplied by the manufacturer or other
prescribed parts.
The use of non-prescribed parts can cause serious accidents such as the unit to fall,
water leakage, electric shock, or fire.
Application
For output function.
(Output terminal / CNB01)
Insulation kit for
high humidity
UTZ-KXRA, UTZ-KXGA
(For indoor unit height
11-3/4 in (298 mm))
UTZ-KXGB
(For indoor unit height
10-1/16 in (256 mm))
Install when the condition under the
roof is over 80% in humidity and over
86°F (30°C) in temperature.
* You cannot use the Fresh air intake kit (UTZ-VXGA) for this product.
2.5. About unit of the length
Name and Shape
Q’ty
Application
Operation manual
1
Installation manual
All Fujitsu General products are manufactured to metric units and tolerances. United
States customary units are provided for reference only. In cases where exact dimensions
and tolerances are required, always refer to metric units.
(This book)
1
For fixing the connection pipe
(Large and Small).
Cable tie (Large)
4
Push mount cable tie
Coupler heat insulation
(Small)
Coupler heat insulation (Large)
1
For transmission and remote
controller cable binding.
For indoor side pipe joint (Small).
1
For indoor side pipe joint (Large).
1
En-2
9371022574-02_IM.indb 2
2018/1/26 10:21:59
Discharge direction setting
3. INSTALLATION WORK
• The discharge direction can be selected as shown below.
Correct initial installation location is important because it is difficult to move unit after it is
installed.
4 direction
3 direction
3.1. Selecting an installation location
Decide the mounting position together with the customer as follows.
WARNING
*1: Please ensure sufficient
service access during
installation.
Select installation locations that can properly support the weight of the indoor. Install the
units securely so that they do not topple or fall.
4 in (100 mm) or more (*1)
CAUTION
Do not install the unit in the following areas:
• Area with high salt content, such as at the seaside.
It will deteriorate metal parts, causing the parts to fail or the unit to leak water.
• Area filled with mineral oil or containing a large amount of splashed oil or steam, such
as a kitchen.
It will deteriorate plastic parts, causing the parts to fail or the unit to leak water.
• Area that generates substances that adversely affect the equipment, such as sulfuric
gas, chlorine gas, acid, or alkali.
It will cause the copper pipes and brazed joints to corrode, which can cause refrigerant
leakage.
• Area that can cause combustible gas to leak, contains suspended carbon fibers or
flammable dust, or volatile inflammables such as paint thinner or gasoline.
If gas leaks and settles around the unit, it can cause a fire.
• Area where animals may urinate on the unit or ammonia may be generated.
Do not use the unit for special purposes, such as storing food, raising animals, growing
plants, or preserving precision devices or art objects.
It can degrade the quality of the preserved or stored objects.
* Select the most appropriate airflow direction from 3 or 4 directions according to the
shape of the room and the installation position.
* When changing the number of outlets, we recommend using the optional AIR OUTLET
SHUTTER PLATE KIT to close the outlet.
* For the specific closing pattern, please refer to the attached AIR OUTLET SHUTTER
PLATE KIT’S MANUAL. (Do so before installing the cassette grille as it will be installed
on the body.)
3.3. Installing the unit
WARNING
Install the air conditioner in a location which can withstand a load of at least 5 times the
weight of the main unit and which will not amplify sound or vibration. If the installation
location is not strong enough, the indoor unit may fall and cause injuries.
If the job is done with the panel frame only, there is a risk that the unit will come loose.
Please take care.
Do not install where there is the danger of combustible gas leakage.
3.3.1 Position the ceiling hole and hanging bolts
Do not install the unit near a source of heat, steam, or flammable gas.
(1) Positions of the ceiling opening, hanging bolt pitch, piping and ducts.
• Ceiling opening and hanging bolt pitch. [unit: in (mm)]
37-3/8 (950)
(Cassette grille)
13/16 to 1-3/4
(20 to 45)
33-7/8 to35-13/16
(860 to 910) (Ceiling opening)
31-5/16 (796)
(Hanging bolt pitch)
5-1/8
(130)
5-1/8 (130)
5-1/8 (130)
7-7/8
(200)
5-1/2 to 5-11/16
(140 to 145)
Unit: in (mm)
11 (256) or more (AUUB 18/24/30)
12 (298) or more (AUUB 36/48)
5-1/8
(130)
1-15/16 to 3-15/16
(50 to 100)
3.2. Installation dimension
Ceiling height is as shown in the figure.
310-1/4 (768)
(Hanging bolt pitch)
Use the “Insulation kit for high humidity” (option), when the condition under the roof is
over 80% in humidity and over 86 °F (30 °C) in temperature. Otherwise, there is a risk
of condensation on the ceiling.
(1) Install the indoor unit on a place having a sufficient strength so that it withstands
against the weight of the indoor unit.
(2) The inlet and outlet ports should not be obstructed; the air should be able to blow all
over the room.
(3) Leave the space required to service the air conditioner.
(4) A place from where the air can be distributed evenly throughout the room by the unit.
(5) Install the unit where connection to the outdoor unit (or RB unit) is easy.
(6) Install the unit where the connection pipe can be easily installed.
(7) Install the unit where the drain pipe can be easily installed.
(8) Install the unit where noise and vibrations are not amplified.
(9) Take servicing, etc., into consideration and leave the spaces. Also install the unit
where the filter can be removed.
13/16 to 1-3/4
(20 to 45)
33-1/16 (840)
(Indoor unit)
If children under 10 years old may approach the unit, take preventive measures so that
they cannot reach the unit.
Decide the mounting position with the customer as follows:
13/16 to 1-3/4
(20 to 45)
1-15/16
(50)
Model
AUUB 18/24/30
AUUB 36/48
Strong and durable ceiling
13/16 to 1-3/4
(20 to 45)
Install the indoor unit, power supply cable, transmission cable, and remote controller
cable at least 40 in (1 m) away from a television or radio receivers. The purpose of this
is to prevent TV reception interference or radio noise.
(Even if they are installed more than 40 in (1 m) apart, you could still receive noise
under some signal conditions.)
33-1/16 (840)
(Indoor unit)
33-7/8 to35-13/16
(860 to 910) (Ceiling opening)
37-3/8 (950)
(Cassette grille)
Install the unit where drainage does not cause any trouble.
Dimension [in (mm)]
A
B
9-11/16
(246)
11-5/16
(288)
10-1/16
(256)
11-3/4
(298)
119 (3,000) or more
70 (1,800) to H
• Refrigerant piping and drain piping positions. [unit: in (mm)]
3-1/8
(80)
Obstruction
3/8
(10)
39 (1,000) or more
1-9/16
(40)
3/8
(10)
60 (1,500)
or more
Floor
H: Maximum height from floor to ceiling
AUUB 36/48
118 (3,000)
125 (3,200)
High Ceiling mode
137 (3,500)
165 (4,200)
* Be sure to make the function settings with the remote controller according to the
installed ceiling height.
Drain pipe
(Connect the attached
drain hose)
13-7/16 (342) 11-9/16 (293)
Gas pipe
1-3/4 (45)
7-1/16
(180)
AUUB 18/24/30
Standard mode
Liquid pipe
5-1/2
(140)
Drain pipe
H [in (mm)]
7-7/8
(200)
Function setting
En-3
9371022574-02_IM.indb 3
2018/1/26 10:21:59
(2) Setting the positions of hanging bolt and ceiling opening.
• Use an installation template (packaging top surface) to set the positions of the hanging
bolt and ceiling opening and drill holes.
(3) Hanging structure.
• Select a strong structure for the hanging location.
• If necessary, reinforce the hanging bolt with quakeproof columnar support material to
prevent shaking.
• Use hanging bolts of M8 to M10.
• Thicknesses of copper pipes used with R410A are as shown in the table.
• Never use copper pipes thinner than those indicated in the table even if they are available on the market.
Thicknesses of Annealed Copper Pipes (R410A)
Pipe outside diameter [in (mm)]
Thickness [in (mm)]
1/4 (6.35)
0.032 (0.80)
3.3.2 Hanging preparations
• Firmly fasten the hanging bolts as
shown in the figure or by another
method.
• Install the hanging bolts at a place
where they would be capable of
holding a weight of at least 110 lbf
(490 N) per bolt.
Hole-in anchor
Hole-in plug
Concrete
Insert
3/8 (9.52)
0.032 (0.80)
1/2 (12.70)
0.032 (0.80)
5/8 (15.88)
0.039 (1.00)
3/4 (19.05)
0.039 (1.20)
4.2. Pipe requirement
CAUTION
Hanging bolt M10
(locally purchased)
Refer to the installation manual for the outdoor unit for description of allowable pipe
length and height difference.
Use pipe with water-resistant heat insulation.
3.3.3 Body installation
CAUTION
WARNING
Perform final tightening by tightening the double nut firmly.
Be sure to install the body horizontally and adjust the height below the body and the
ceiling surface properly.
(1) Install the attached washer and nut (prepared on site) onto the hanging bolt.
(2) Hook the body onto the hanging bolt.
(3) Adjust the dimensions of the ceiling surface from the body.
After installing the cassette grille, you can make fine adjustment of the height of the
body. For details, refer to the installation manual of the cassette grille.
Hanging bolt
(locally purchased)
Install heat insulation around both the gas and liquid pipes. Failure to do so may cause
water leaks.
Use heat insulation with heat resistance above 248 °F (120 °C). (Reverse cycle model
only)
In addition, if the humidity level at the installation location of the refrigerant piping is
expected to exceed 70 %, install heat insulation around the refrigerant piping. If the
expected humidity level is 70 to 80 %, use heat insulation that is 9/16 in (15 mm) or
thicker and if the expected humidity exceeds 80 %, use heat insulation that is 13/16 in
(20 mm) or thicker. If heat insulation is used that is not as thick as specified, condensation may form on the surface of the insulation. In addition, use heat insulation with heat
conductivity of 0.045 W/(m·K) or less (at 68 °F (20 °C)).
[Unit: in (mm)]
4.3. Flare connection (pipe connection)
Nut A
(locally purchased)
Washer
(Accessories)
WARNING
1-3/16 (30) or more
After installing the body,
tighten the nuts.
Washer
(Accessories)
Tighten the flare nuts with a torque wrench using the specified tightening method. Otherwise, the flare nuts could break after a prolonged period, causing refrigerant to leak and
generate hazardous gas if the refrigerant comes into contact with a flame.
4.3.1 Flaring
Nut B (Double Nut)
(locally purchased)
Use special flare tool exclusive for R410A.
3/8 to 9/16 (10 to 15)
3.3.4 Leveling
• Using a level, or vinyl hose filled with water, fine adjust so that the body is level.
• Inclined installation so as the drain pipe side is higher may cause a malfunction of the
float switch, and may cause water leakage.
(1) Cut the connection pipe to the necessary length with a pipe cutter.
(2) Hold the pipe downward so that cuttings will not enter the pipe and remove any burrs.
(3) Insert the flare nut (always use the flare nut attached to the indoor and outdoor units
(or RB unit) respectively) onto the pipe and perform the flare processing with a flare
tool. Use the special R410A flare tool. Leakage of refrigerant may result if other flare
nuts are used.
(4) Protect the pipes by pinching them or with tape to prevent dust, dirt, or water from
entering the pipes.
Drain pipe
Check if [L] is flared uniformly and
is not cracked or scratched.
B
Die
A
L
Pipe
Vinyl hoses
4. PIPE INSTALLATION
CAUTION
Pipe outside diameter
[in (mm)]
Dimension A [in (mm)]
Flare tool for R410A,
clutch type
(0)
Dimension B 0-0.015
(-0.4)
[in (mm)]
1/4 (6.35)
3/8 (9.1)
3/8 (9.52)
1/2 (13.2)
Be more careful that foreign matter (oil, water, etc.) does not enter the piping than with
refrigerant R410A models. Also, when storing the piping, securely seal the openings by
pinching, taping, etc.
1/2 (12.70)
While welding the pipes, be sure to blow dry nitrogen gas through them.
5/8 (15.88)
3/4 (19.7)
3/4 (19.05)
15/16 (24.0)
4.1. Selecting the pipe material
CAUTION
Do not use existing pipes from another refrigeration system or refrigerant.
Use pipes that have clean external and internal sides without any contamination which
may cause trouble during use, such as sulfur, oxide, dust, cutting waste, oil, or water.
0 to 0.020
(0 to 0.5)
5/8 (16.6)
When using conventional (R22) flare tools to flare R410A pipes, the dimension A should
be approximately 0.020 in (0.5 mm) more than indicated in the table (for flaring with
R410A flare tools) to achieve the specified flaring. Use a thickness gauge to measure the
dimension A. It is recommended that a R410A flaring tool is used.
Width across
flats
Pipe outside diameter
[in (mm)]
Width across flats of Flare
nut [in (mm)]
1/4 (6.35)
11/16 (17)
3/8 (9.52)
7/8 (22)
It is necessary to use seamless copper pipes.
Material : Phosphor deoxidized seamless copper pipes
It is desirable that the amount of residual oil is less than 0.04 oz/100 ft (40 mg/10 m).
1/2 (12.70)
1 (26)
Do not use copper pipes that have a collapsed, deformed, or discolored portion (especially on the interior surface). Otherwise, the expansion valve or capillary tube may
become blocked with contaminants.
5/8 (15.88)
1-1/8 (29)
3/4 (19.05)
1-7/16 (36)
Improper pipe selection will degrade performance. As an air conditioner using R410A
incurs pressure higher than when using conventional (R22) refrigerant, it is necessary to
choose adequate materials.
En-4
9371022574-02_IM.indb 4
2018/1/26 10:21:59
4.3.2 Bending pipes
• If pipes are shaped by hand, be careful not to collapse them.
• Do not bend the pipes in an angle more than 90°.
• When pipes are repeatedly bent or stretched, the material will harden, making it difficult
to bend or stretch them anymore.
• Do not bend or stretch the pipes more than 3 times.
5. INSTALLING DRAIN PIPES
WARNING
Do not insert the drain piping into the sewer where sulfurous gas occurs. (Heat exchange erosion may occur)
Insulate the parts properly so that water will not drip from the connection parts.
CAUTION
Check for proper drainage after the construction by using the visible portion of transparent drain port and the drain piping final outlet on the body.
To prevent breaking of the pipe, avoid sharp bends.
If the pipe is bent repeatedly at the same place, it will break.
CAUTION
4.3.3 Pipe connection
Do not apply adhesive agent on the drain port of the body. (Use the attached drain hose
and connect the drain piping)
CAUTION
Be sure to install the pipe against the port on the indoor unit and the outdoor unit correctly. If the centering is improper, the flare nut cannot tightened smoothly. If the flare
nut is forced to turn, the threads will be damaged.
Do not remove the flare nut from the indoor unit pipe until immediately before connecting the connection pipe.
Do not use mineral oil on flared part. Prevent mineral oil from getting into the system as
this would reduce the lifetime of the units.
Hold the torque wrench at its grip, keeping it at a right angle with the pipe, in order to
tighten the flare nut correctly.
(1) Detach the caps and
plugs from the pipes.
(2) Center the pipe against
the port on the indoor
unit, and then turn the
flare nut by hand.
• Install the drain pipe with downward gradient (1/100 to 1/50) and so there are no rises or
traps in the pipe. Unsmooth draining caused by accumulated water flow in the pipe may
cause clogged drain.
• Use general hard polyvinyl chloride pipe (Ø 3/4 in [I.D.]; Ø 1-1/16 in [O.D.]).
• When the pipe is long, install supporters.
• Do not perform air bleeding. DrainPipe size
age may be blown out.
(Ø 3/4 in [I.D.]; Ø 1-1/16 in [O.D.])
• If it is impossible to have sufficient gra- Drain pipe
dient of pipe, perform drain lift-up.
60 to 78 in (1.5 to 2.0 m)
Hanging fittings
Connection pipe (Gas)
Connection pipe
(Liquid)
Ø 3/4 in [I.D.]; Ø 1-1/16 in [O.D.]
Downward gradient 1/100 to 1/50
(3) When the flare nut is
tightened properly by
your hand, hold the body
side coupling with a
separate spanner, then
tighten with a torque
wrench. (See the table
below for the flare nut
tightening torques.)
Tighten with 2
wrenches.
PROHIBITED:
Holding wrench
Flare nut
Torque wrench
Rise
Indoor unit pipe (Body side)
Flare nut [in (mm)]
Connection pipe
Tightening torque [lbf·ft (N·m)]
1/4 (6.35) dia.
11.8 to 13.3 (16 to 18)
3/8 (9.52) dia.
23.6 to 31.0 (32 to 42)
1/2 (12.70) dia.
36.1 to 45.0 (49 to 61)
5/8 (15.88) dia.
46.5 to 55.3 (63 to 75)
3/4 (19.05) dia.
66.4 to 81.1 (90 to 110)
CAUTION
Air bleeding
When lifting up drain:
• Height of inclined pipe should be less than 33 in (850 mm) from the ceiling. A rise dimension over this range will cause leakage.
• Lift up the pipe vertically at the position of 11 in (300 mm) or less from the unit.
Downward gradient
11 in (300 mm) or less
1/100 to 1/50
Ø 3/4 in [I.D.];
Ø 1-1/16 in [O.D.]
local arrangement
33 in (850 mm)
or less
Horizontal or
upward gradient
4.4. Installing heat insulation
After checking for gas leaks (refer to the Installation Manual of the outdoor unit), perform
this section.
Trap
33 in (850 mm)
or less
Ø 1 in [I.D.]; Ø 1-5/16 in [O.D.] or more
Downward gradient 1/100 to 1/50
Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to do
so may cause water leaks.
After checking for gas leaks, insulate by wrapping insulation around the 2 parts (gas and
liquid) of the indoor unit coupling, using the Coupler heat insulation.
After installing the Coupler heat insulation, wrap both ends with vinyl tape so that there is
no gap.
Cable tie (Large)
(Accessories)
Working procedure
Coupler heat
insulation
(Accessories)
No gap
Body
Be sure to overlap
the insulation
Coupler heat
insulation
(1) Install the attached drain hose to the drain port of the body. Install the hose band
from the top of the hose within the graphic display area. Secure firmly with the hose
band.
(2) Use vinyl adhesive agent to glue the drain piping (PVC pipe VP25) which is prepared
on site or elbow socket. (Apply color adhesive agent evenly until the gauge line and
seal)
(3) Check the drainage. (See separate diagram)
(4) Install the heat insulation.
(5) Use the attached heat insulation to insulate the drain port and band parts of the body.
CAUTION
Must fit tightly against body without any gap.
En-5
9371022574-02_IM.indb 5
2018/1/26 10:21:59
Install the knob
faces upward
Attached hose band
(Accessories)
Attached drain hose
heat insulation
(Accessories)
Locally arranged
vinyl pipe
Attached drain hose
(Accessories)
Attached heat insulation
(Accessories)
Securely connect the connection cables to the terminal board. In addition, secure the
cables with wiring holders. Improper connections, either in the wiring or at the ends of
the wiring, can cause a malfunction, electric shock, or fire.
Always fasten the outside covering of the connection cable with the cable clamp. (If the
insulator is chafed, electric discharge may occur.)
We suggest installing GFEB breakers or follow local electrical code. When installing this
system, install using ground fault equipment breakers (GFEB) to reduce the risk of leaking current which result in electric shock or potential fire.
Always connect the earth (ground) cable.
Improper earthing (grounding) work can cause electric shocks.
Install the remote controller cables so as not to be direct touched with your hand.
Perform wiring work in accordance with standards so that the air conditioner can be
operated safely and positively.
Connect the connection cable firmly to the terminal board. Imperfect installation may
cause a fire.
If the supply cable is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
CAUTION
(a) Top view
(b) Side view Ø 3/4 in [I.D.];
Ø 1-1/16 in [O.D.]
Applying area
of adhesive
1-3/8 in (35 mm)
Hose Band
Earth (Ground) the unit.
Do not connect the earth (ground) cable to a gas pipe, water pipe, lightning rod, or a
telephone earth (ground) cable.
Improper earthing (grounding) may cause electric shock.
Do not connect power supply cables to the transmission or remote controller terminals,
as this will damage the product.
Never bundle the power supply cable and transmission cable, remote control cable
together. Separate these cable by 2 in (50 mm) or more. Bundling these cables together
will cause miss operation or breakdown.
3/16 to 3/8 in
(5 to 10 mm)
Gauge line
3/16 in (4 mm)
or less
13/16 in (20 mm)
(c) Top view
(d) Hose opening view
Wind the attached heat insulation
around the hose band
Make sure the
alignment is on top
When handling PCB, static electricity charged in the body may cause malfunction of the
PCB. Follow the cautions below:
• Establish an earth (ground) for the indoor and outdoor units and peripheral devices.
• Cut power (breaker) off.
• Touch metal part of the indoor units for more than 10 seconds to discharge static
electricity charged in the body.
• Do not touch terminals of parts and patterns implemented on PCB.
6.1. Electrical requirement
• Select the power cable type and size
in accordance with relevant local and
national regulations.
Make sure there are no gaps
Voltage rating
208/230 V
Operating range
187 to 253 V
• Specifications for local wiring power cord and branch wiring are in compliance with local
code
• Max. wire length: Set a length so that the voltage drop is less than 2%. Increase the wire
diameter when the wire length is long.
Breaker should be installed at every refrigerant system. Do not use a breaker in a different
refrigerant system.
Refer to the table for the breaker specifications of each installation condition. Perform
the power crossover wiring within the range of the same refrigerant system. When the
crossover wiring is done, make a connection for indoor units to satisfy conditions A and B
below.
NOTE: Check for drainage
Pour about 1 liter of water from
the position shown in the diagram or from the airflow outlet
to the dew tray. Check for any
abnormalities such as strange
noises and whether the drain
pump functions normally.
A. Current breaker requirements
6. ELECTRICAL WIRING
WARNING
Electrical work must be performed in accordance with this Manual by a person certified
under the national or regional regulations. Be sure to use a dedicated circuit for the unit.
An insufficient power supply circuit or improperly performed electrical work can cause
serious accidents such as electric shock or fire.
Before starting work, check that power is not being supplied to the all units.
For wiring, use the prescribed type of cables, connect them securely, making sure that
there are no external forces of the cables applied to the terminal connections.
Improperly connected or secured cables can cause serious accidents such as overheating the terminals, electric shock, or fire.
Securely install the electrical box cover on the unit.
An improperly installed electrical box cover can cause serious accidents such as electric
shock or fire through exposure to dust or water.
Install sleeves into any holes made in the walls for wiring. Otherwise, a short circuit
could result.
Model
MCA
AUUB18TLAV1
0.33 A
AUUB24TLAV1
0.40 A
AUUB30TLAV1
0.68 A
AUUB36TLAV1
0.78 A
AUUB48TLAV1
1.40 A
MAX. CKT. BKR
(Fuse capacity)
15 A
• MCA: Minimum Circuit Ampacity
• MAX. CKT. BKR : Maximum Circuit
Breaker
When the power crossover wiring is
done, make it so that the total of the
MCA of the connected RB units and
indoor units does not exceed the 11 A.
For RB unit MCA, refer to the RB unit
installation manual.
If the capacity of connected RB units
and indoor units exceeds the upper limit,
either add breakers or use a breaker with
a greater capacity.
B. Earth leakage breaker requirements
Breaker capacity
Maximum connectable “indoor units”
or “indoor units +
RB units” (*1)
30 mA, 0.1 sec or less
36 or less
100 mA, 0.1 sec or less
37 to 121 (*2)
*1: Heat pump type: indoor units,
Heat recovery type: indoor units
and RB units.
*2: If the 100 mA capacity breaker is
not provided, split the quantity of
the indoor units into small groups
of 9 units or less and provide a
breaker with capacity of 30 mA for
each group.
Use the included connection cables and power cables or ones specified by the manufacturer. Improper connections, insufficient insulation, or exceeding the allowable current
can cause electric shock or fire.
Do not modify the power cables, use extension cables, or use any branches in the wiring. Improper connections, insufficient insulation, or exceeding the allowable current can
cause electric shock or fire.
Match the terminal block numbers and connection cable colors with those of the outdoor
unit (or RB unit). Erroneous wiring may cause burning of the electric parts.
En-6
9371022574-02_IM.indb 6
2018/1/26 10:21:59
6.1.1 Cable specifications
Use
Cable size
(AWG)
Power supply
cable
18 to 12
Transmission
cable
22
Remote
controller
cable
(2-wire type)
Strip 1 in
(25 mm)
Cable type
22 to 16
18
Remark
Sheathed PVC cable
2 cable + earth
(ground)
22 AWG LEVEL 4 (NEMA)
non-polar 2 core, twisted
pair solid core diameter
0.026 in (0.65mm)
LONWORKS®
compatible cable
Sheathed PVC cable
Non polar 2 core,
twisted pair
Thermostat cable 2 core
Use sheathed non
twisted pair cable
Loop
Screw with
special washer
Screw with
special washer
Cable
Cable end (Loop)
Cable end (Loop)
Terminal block
Cable
6.2. Wiring method
Do not apply branch wiring. It may result electric shock or fire.
Outdoor unit or RB unit *1
Breaker 1: Ground Fault Equipment
Breaker (GFEB)
Breaker 2: Maximum Circuit Breaker
(MAX. CKT. BKR)
Transmission
WARNING
When using solid core cables, do not use the ring terminal. If you use the solid core
cables with the ring terminal, the ring terminal's pressure bonding may malfunction and
cause the cables to abnormally heat up.
B. For strand wiring
Indoor unit
Indoor unit
Indoor unit
Remote
control
Transmission
Power supply
Breaker 2
Breaker 2
Breaker 1
Breaker 1
Power supply
Breaker 2
Breaker 1
*2
*2
Remote controller
Remote
(Slave)
controller
*2
Remote controller
(Master)
(1) Use ring terminals with insulating sleeves as shown in the figure below to connect to
the terminal block.
(2) Securely clamp the ring terminals to the cables using an appropriate tool so that the
cables do not come loose.
(3) Use the specified cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(4) Use an appropriate screwdriver to tighten the terminal screws. Do not use a screwdriver that is too small, otherwise, the screw heads may be damaged and prevent the
screws from being properly tightened.
(5) Do not tighten the terminal screws too much, otherwise, the screws may break.
(6) See the table for the terminal screw tightening torques.
(7) Please do not fix 2 power supply cables with 1 screw.
Strip 3/8 in
Ring terminal
(10 mm)
*1: When connecting to the Heat Recovery System, refer to the installation manual of the
RB unit.
*2: The 3-wire type remote controller is not used.
Sleeve
(Crossover wiring of power supply)
Indoor unit
Power supply
Indoor unit
Power supply
Screw with
special washer
Indoor unit
Power supply
Screw with
special washer
Cable
Ring terminal
Ring terminal
Terminal block
Pull box
Breaker 2
Breaker 1
Cable
Pull box
WARNING
: Disconnect switch
Power supply
Use ring terminals and tighten the terminal screws to the specified torques, otherwise,
abnormal overheating may be produced and possibly cause heavy damage inside the
unit.
6.3. Unit wiring
Terminal number
Tightening torque
M3.5 screw (Power supply/L, N, GND)
11 to 16 lbf·in (1.2 to 1.8 N·m)
• Before attaching the cable to terminal block.
6.3.1 Power supply cable
Conduit connector
7-7/8 in (200 mm)
6.3.2 Transmission and Remote controller cable
Transmission cable
Remote controller cable
1-3/16 in (30 mm)
Earth (ground)
wire
8-1/4 in (210 mm)
A. For solid core wiring
(1) To connect the electrical terminal, follow the below diagram and connect after looping
it around the end of the cable.
(2) Use the specified cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(3) Use an appropriate screwdriver to tighten the terminal screws.
Do not use a screwdriver that is too small, otherwise, the screw heads may be damaged and prevent the screws from being properly tightened.
(4) Do not tighten the terminal screws too much, otherwise, the screws may break.
(5) See the table for the terminal screw tightening torques.
(6) Please do not fix 2 power supply cables with 1 screw.
Shield
cable
(no film)
1-3/16 in (30 mm)
1-3/4 in
(45 mm)
• Connect remote controller and transmission cables as shown in figure below.
GOOD
PROHIBITED
Different diameter
Connect to 1 side
WARNING
Tighten the terminal screws to the specified torques, otherwise, abnormal overheating
may be produced and possibly cause heavy damage inside the unit.
En-7
9371022574-02_IM.indb 7
2018/1/26 10:22:00
Terminal number
Tightening torque
M3 screw (Transmission /X1, X2)
(Remote controller /Y1, Y2)
(2) Please firmly tighten Connection cable and Remote controller cable with the attached
cable tie.
4.4 to 5.3 Ibf·in (0.5 to 0.6 N·m)
X1, X2: Transmission cable
CAUTION
To peel the film from the lead cable, use a dedicated tool that will not damage the
conductor cable.
Cut
When installing a screw on the terminal block, do not cut the cable by overtightening the
screw. On the other hand, an undertightened screw can cause faulty contact, which will
lead to a communication failure.
Push mount cable tie (accessories)
6.4. Connection of wiring
(1) Remove the control box cover and install each connection cable.
Attach the conduit connector on
the wiring connecting port.
(The grommet edging and the
connection cable clamp are not
used.)
Y1, Y2: Remote controller cable
(do not use Y3.)
Conduit connector
Lock nut
Wiring connecting port
(for power supply cable)
(3) Replace the Control box
cover and Wiring cover.
Securely tighten the
screws.
Wiring
connecting port (for
transmission cable
and remote controller
cable)
Wiring cover
Control box cover
Cure the wiring connecting
port and remote controller
connecting port with putty or
heat insulation so that insects
or dust will not enter the unit.
L2
(N)
L1
CAUTION
1
2
3
Earth
(ground)
L2
L1 (N)
Lock nut
Do not bundle the remote controller cable, or wire the remote controller cable in parallel,
with the indoor unit connection wire (to the outdoor unit) and the power supply cable. It
may cause erroneous operation.
(4) Fix the conduit with the supporters as shown below.
Conduit (Power supply cable)
Supporter
Indoor unit
Conduit connector
(L1, L2 (N): Power supply cable)
30 in
(756 mm)
or less
54 in
(1,361 mm)
or less
54 in
(1,361 mm)
or less
54 in
(1,361 mm)
or less
En-8
9371022574-02_IM.indb 8
2018/1/26 10:22:00
● Apply voltage terminal ([CNA01], [CNA03])
6.5. Optional parts wiring
When a power supply must be provided at the input device you want to connect, use the
Apply voltage terminal ([CNA01], [CNA03]).
6.5.1 Connector and DIP switch position
Output terminal
CNB01
CNA03
DC power supply
12 to 24V
Controller PCB
Input
device 1
Apply voltage terminal
CNA01
*1
P.C.B
Load
resistance
CNA01
*a
DIP switch
(SET 2)
OFF
Load
resistance
*a
SW1 SW3
SW2 SW4
Dry contact terminal
Input signal type switching
Output terminal
For external output
6.5.2 Connection methods
Wire modification
IMPORTANT:
(1) Remove insulation from wire atBe sure to insulate the connection between the
tached to wire kit connector.
wires.
(2) Remove insulation from field
Wire kit connector
supplied cable. Use crimp type
(optional parts)
insulated butt connector to join field Locally purchased
cable and wire kit wire.
(3) Connect the wire with connecting
wire with solder.
Solder and insulate the connected parts.
Connection terminals and wiring arrangement
In following figure, all the possible connectors are connected for description.
In actual installation, you cannot connect all the connectors at once.
Connected unit
*1: Make the power supply DC 12 to 24 V. Select a power supply capacity with an ample
surplus for the connected load.
Do not impress a voltage exceeding 24 V across pins 1-2, and 1-3.
*a: The allowable current is DC 5 mA to 10 mA. (Recommended: DC 5 mA)
Provide a load resistance such that the current becomes DC 10 mA or less.
Select very low current use contacts (usable at DC 12 V, DC 1 mA or less).
*b: The polarity is [+] for pin 1 and [-] for pin 2 and 3. Connect correctly.
When connected to Apply voltage terminals of multiple indoor units with a connected unit,
be sure to make a branch outside the indoor unit using a pull box, etc. as shown on below
example.
DC power supply
12 to 24V
Input
device 1
CNA01
CNA03
CNA02
CNA04
DIP switch SET 2 (SW2)
CNB01
Application
Apply voltage terminal
For external input
Load
resistance
Input
device 2
Name
CNA03
Load
resistance
P.C.B
CNA01
P.C.B
CNA01
P.C.B
Connected unit
Cable hooks
1
2
3
CNA01
Indoor unit
ON
Indoor unit
CNA02
CNA04
Dry contact terminal
*a
Indoor unit
SET 2
Input
device 3
Input
device 2
*b
Load
resistance
L2
L1 (N)
● Dry contact terminal ([CNA02], [CNA04])
When a power supply is unnecessary at the input device you want to connect, use the Dry
contact terminal ([CNA02], [CNA04]).
P.C.B
CNA01 CNA03
CNA02
CNB01
*c
Ch 1
CNA04
*c
Ch 2
Cable clamp
6.6. External input and external output (Optional parts)
6.6.1 External input
• Indoor unit can be Operation/Stop, Emergency stop or Forced stop by using indoor unit
PCB CNA01 or CNA02.
• “Operation/Stop” mode, “Emergency stop” mode or “Forced stop” mode can be selected
with function setting of indoor unit.
• Indoor unit can be Forced thermostat off by using indoor unit PCB CNA03 or CNA04.
• A twisted pair cable (22 AWG) should be used. Maximum length of cable is 492 ft (150
m).
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• The wire connection should be separate from the power cable line.
CNA02
GND
*d
*c
Ch 3
CNA04
Connected unit
*c: Select very low current use contacts (usable at DC 12 V, DC 1 mA or less).
*d: The wiring is different from Apply voltage terminals. Be sufficiently careful when wiring.
Input select
Use either one of these types of terminal according to the application. (Both types of
terminals cannot be used simultaneously.)
En-9
9371022574-02_IM.indb 9
2018/1/26 10:22:00
When connected to Dry contact terminals of multiple indoor units with a connected unit,
insulate each indoor unit with relay, etc. as shown on below example.
[“Edge” input only]
Connector
K4
CNA02
Indoor unit
P.C.B
K1
P.C.B
K2
K5
CNA02
Indoor unit
Power supply for relay
● Forced thermostat off function
Input signal
Ch3 of CNA03 or CNA04
Command
OFF → ON
Thermostat off
ON → OFF
Normal
6.6.2 External output
• A twisted pair cable (22AWG) should be used. Maximum length of cable is 82 ft (25m).
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• Output voltage: Hi DC12V±2V, Lo 0V.
• Permissible current: 50mA
Output select
● When indicator etc. are connected directly
P.C.B
K3
Input device 1
K6
CNA02
Indoor unit
P.C.B
Indicator 1
CNB
01
Indicator 2
Input device 2
K1 - K6: Relay
(Device for DC Current)
Indicator 3
Indicator 4
NOTE :
When connected to multiple indoor units directly, it will cause breakdown.
connected unit
● When connecting with unit equipped with a power supply
Operation behavior
● Input signal type
P.C.B
Edge
The input signal type can be selected.
It is switched by DIP switch on the indoor unit PCB.
DIP switch [Set 2 SW2]
Connected
device 1
Input signal type
OFF (Factory setting)
Edge
ON
Pulse
Pulse
Connected
device 2
The width of pulse must be
longer than 200 msec.
Connected
device 3
● When function setting is “Operation/Stop” mode.
Connected
device 4
[In the case of “Edge” input]
Connector
Input signal
Ch1 of CNA01 or CNA02
Command
OFF → ON
Operation
ON → OFF
Stop
CNA01 or CNA02
Input signal
connected unit
Operation behavior
Connector
Command
Ch1
OFF → ON
Operation
Ch2
OFF → ON
Stop
* The last command has priority.
* The indoor units within the same remote controller group operates in the same mode.
Ch1 of CNA01 or CNA02
Command
CNA01 or CNA02
External output 3
Pins 1-4
DC 12 V
External output 4
Pins 1-5
0V
External heater OFF
DC 12 V
External heater ON
0V
Error
Indoor unit fan stop
Indoor unit fan operation
● Indoor unit fan setting for external heater
Fan setting when turning ON output to the connected external heater can be set by
changing Dip switch on PC board.
Command
Emergency stop
Ch2
OFF → ON
Normal
* All indoor units of same refrigerant system stops when Emergency stop operates.
● When function setting is “Forced stop” mode.
Dip switch
[SET2 SW3]
Fan setting when
ON is output to the
external heater
OFF
(Factory setting)
OFF
ON
ON
Explanation
For the fan setting details, see the
Design & Technical Manual.
7. FIELD SETTING
[In the case of “Edge” input]
Input signal
Command
OFF → ON
Forced stop
ON → OFF
Normal
There are 3 methods for address setting by FIELD SETTING as follows.
Please set by either of the methods.
Each setting method is described in below (1) to (3).
(1) IU AD, REF AD SW settings: This section (7.1. Setting the address)
[In the case of “Pulse” input]
CNA01 or CNA02
Normal
DC 12 V
Normal
OFF → ON
Connector
Operation
Emergency stop
Ch1
Ch1 of CNA01 or CNA02
0V
ON → OFF
Input signal
Connector
DC 12 V
Status
Stop
OFF → ON
[In the case of “Pulse” input]
Connector
0V
External output 2
Pins 1-3
CNB01
[In the case of “Edge” input]
Input signal
Output voltage
External output 1
Pins 1-2
● When function setting is “Emergency stop” mode.
Connector
Relay (Locally purchased)
* If function setting "60" is set to "00"
[In the case of “Pulse” input]
Connector
CNB
01
Input signal
Command
Ch1
OFF → ON
Forced stop
Ch2
OFF → ON
Normal
(2) Remote controller settings:
Refer to the wired or wireless remote controller manual
for detailed setting information. (Set IU AD, REF AD
SW to 0)
(3) Automatic address settings: Refer to the outdoor unit manual for detailed setting
information. (Set IU AD, REF AD SW to 0)
* When the forced stop is triggered, indoor unit stops and Operation/Stop operation by a
remote controller is restricted.
* When forced stop function is used with forming a remote controller group, connect the
same equipment to each indoor unit within the group.
• Selection method of functions
“Operation/Stop” mode or “Emergency stop” mode, “Forced stop” mode can be selected
with function setting of indoor unit.
En-10
9371022574-02_IM.indb 10
2018/1/26 10:22:00
• Custom code setting for indoor unit
7.1. Setting the address
IU AD
Set the DIP switch SET3 SW1, 2, referring to the
figure and table below.
CAUTION
×10
Use an insulated screwdriver to set the dip switches.
REF AD
×1
SET3
• Open the cover referring to the figure below. Close and fix the cover after addressing
setting.
For refrigerant
circuit address
For indoor
unit address
(1) Loosen the screw.
IU AD
REF AD
×1
×10
SET3
×1
SET4
DIP switch “SET3”
DIP switch “SET3”
ON
DIP switch
SET3
RC AD
OFF
×10
×10
RC AD
×1
SW SW SW SW
1 2 3 4
Custom code
A (Factory
setting)
B
C
D
SW1
OFF
ON
OFF
ON
SW2
OFF
OFF
ON
ON
SET4
7.3. Function setting
(2) Slide the cover and open it.
7.1.1 Indoor unit address
• Rotary switch (IU AD × 1)...Factory setting “0”
• Rotary switch (IU AD × 10)...Factory setting “0”
When connecting multiple indoor units to 1 refrigerant system, set the address at IU AD
SW as shown in the Table A.
7.1.2 Refrigerant circuit address
• Rotary switch (IU AD × 1)...Factory setting “0”
• Rotary switch (IU AD × 10)...Factory setting “0”
In the case of multiple refrigerant systems, set REF AD SW as shown in the Table A for
each refrigerant system.
Set to the same refrigerant circuit address as the outdoor unit.
Setting
Setting range
Indoor unit address
Type of switch
* Turning on the power to the indoor units initializes EEV, so make sure the piping air tight
test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Function
Filter indicator interval
Function
number
11
Setting
example 2
0 to 63
IU AD × 10
Refrigerant circuit
address
• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
• Refer to “7.1. Setting the address” for indoor unit address and refrigerant circuit address
settings.
• Turn the power of the indoor unit ON before starting the setting.
IU AD × 1
Filter indicator action
REF AD × 10
REF AD × 1
• If working in an environment where the wireless remote controller can be used, the addresses can also be set using the remote controller.
• If setting the addresses using the wireless remote controller, set the indoor unit address
and refrigerant circuit address to “00”.
(For information on setting using the wireless remote controller.)
Ceiling
airflow
20
Vertical
airflow
direction
23
Table A
Address
Refrigerant
circuit
0
1
2
3
4
5
6
7
8
9
10
11
12
.
.
.
99
Rotary switch setting
REF AD SW
× 10
×1
0
0
0
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
9
1
0
1
1
1
2
.
.
.
.
.
.
9
9
Address
Rotary switch setting
IU AD SW
× 10
×1
0
0
0
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
9
1
0
1
1
1
2
.
.
.
.
.
.
Indoor unit
0
1
2
3
4
5
6
7
8
9
10
11
12
.
.
.
63
6
Cool air
temperature
trigger
Heat air
temperature
trigger
Auto restart
Cool Air
Prevention
00
Standard
01
Longer
02
Shorter
00
Enable
01
Disable
02
Display only
on central
remote
controller
00
Standard
01
High Ceiling
00
Standard
01
Adjust
00
Standard
01
Adjust (1)
02
Adjust (2)
00
Standard
01
Adjust (1)
02
Adjust (2)
03
Adjust (3)
00
Enable
01
Disable
00
Super low
01
Follow the
setting on
the remote
controller
00
Start/Stop
01
Emergency
stop
02
Forced stop
00
All
01
Display only
on central
remote
controller
13
Setting example 63
0 to 99
Setting number
30
31
40
43
3
Do not set the indoor unit address (IU AD SW) at 64 to 99.
It may result in failure.
7.2. Custom code setting
External
control
• Selecting the custom code prevents the indoor unit mix-up. (figure below)
(Up to 4 codes can be set.)
• Perform the setting for both the indoor unit and the remote controller.
Confusion
Code change
Indoor unit
Remote
controller
A
A
B
B
C
C
46
D
D
Error report
target
47
Default
Details
Adjust the filter cleaning interval
notification. If the notification
is too early, change to setting
01. If the notification is too late,
change to setting 02.
Enable or disable the filter indicator. Setting 02 is for use with a
central remote controller.
Regulate the airflow according
to the needs of the installation
location. When set to 01, the air
flow will be stronger. (Cassette
type only)
Adjust the vertical airflow direction. All airflow direction louvers
are adjusted together.
Adjust the cool air trigger
temperature. To lower the trigger
temperature, use setting 01. To
raise the trigger temperature,
use setting 02.
Adjust the heat air trigger
temperature. To lower the trigger
temperature by 6 degrees C, use
setting 01. To lower the trigger
temperature by 4 degrees C, use
setting 02. To raise the trigger
temperature, use setting 03.
Enable or disable automatic
system restart after a power
outage.
Restrain the cold airflow with
making the airflow lower when
starting heating operation. To
correspond to the ventilation,
set to 01.
Allow an external controller to
start or stop the system, or to
perform an emergency stop.
* If an emergency stop is
performed from an external
controller, all refrigerant
systems will be disabled.
* If forced stop is set, indoor
unit stops by the input to the
external input terminals, and
Start/Stop by a remote controller is restricted.
Change the target for reporting
errors. Errors can either be reported in all locations, or only on
the central remote controller.
En-11
9371022574-02_IM.indb 11
2018/1/26 10:22:00
Function
Function
number
Fan setting when
cooling
thermostat
OFF
Setting number
00
Follow the
setting on
the remote
controller
01
Stop
49
Default
When set to 01, the fan stops
when the thermostat is OFF in
cooling operation. Connection
of the wired remote controller (2-wire type or 3-wire type)
and switching its thermistor are
necessary.
00 Mode 0
Switching
functions
for external
inputs and
external
outputs
terminals
60
01
02
03
04
05
06
07
08
00
01
Control
switching
of external
heaters
02
61
03
04
00
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Auxiliary
heater control 1
Auxiliary
heater control 2
Heat pump
prohibition
control
Heater selection control
using outdoor
temperature 1
Heater selection control
using outdoor
temperature 2
Setting 0
01 Setting 1
Operating
temperature
switching
of external
heaters
62
02 Setting 2
03 Setting 3
04 Setting 4
05 Setting 5
Auto mode
type
68
Single
setpoint auto
00
mode
(traditional)
Dual setpoint
01
auto mode
8. CASSETTE GRILLE INSTALLATION
Details
• Set this function when connecting the VRF system to a ventilator, economizer, humidifier, or
other external device.
• The connection terminal functions can be changed depending
on the type of external device.
For details of the connection terminal functions, see the Design
& Technical Manual.
Sets the control method for the
external heater being used. For
details of the control method, see
the Design & Technical Manual.
• Sets the temperature conditions
when the external heater is ON.
• For the temperature conditions,
see "Temperature conditions
when the external heater is ON".
For a more detailed explanation, see the Design & Technical
Manual.
Switch the setting method of
auto mode to single or dual
(cooling/heating).
For heat pump systems, it is
necessary to set the master
indoor unit (by wired remote
controller).
04 4°F (2.0°C)
05 5°F (2.5°C)
06 6°F (3.0°C)
Refer to the Installation Manual for the outdoor unit if the PCB for the outdoor unit is to be
used for the test run.
9.2. Test run using remote controller
• Refer to the Installation Manual for the remote controller to perform the test run using the
remote controller.
• When the air conditioner is being test run, the OPERATION and TIMER indicator lamp
flash slowly at the same time.
Check items
If not performed correctly
Has the indoor unit been installed
correctly?
Vibration, noise, indoor unit may
drop
Has there been a check for gas leaks
(refrigerant pipes)?
No cooling, No heating
Has heat insulation work been completed?
Water leakage
Does water drain easily from the indoor
units?
Water leakage
Is the voltage of the power source the
same as that indicated on the label on
the indoor unit?
No operation, heat or burn damage
Are the wires and pipes all connected
completely?
No operation, heat or burn damage
Is the indoor unit earthed (grounded)?
Short circuit
Is the connection cable the specified
thickness?
No operation, heat or burn damage
Are the inlets and outlets free of any
obstacles?
No cooling, No heating
Does start and stop air conditioner
operation by remote control unit or
external device?
No operation
Check
box
After installation is completed, has the
proper operation and handling been
explained to the user?
02 2°F (1.0°C)
69
9.1. Test run using Outdoor unit (PCB)
Pay special attention to the check items below when installing the indoor unit(s). After
installation is complete, be sure to check the following check items again.
01 1°F (0.5°C)
03 3°F (1.5°C)
9. TEST RUN
10. CHECK LIST
00 0°F (0°C)
Deadband
value
• Operate according to the installation Manual CASSETTE GRILLE.
• Be sure to confirm there is no gap between the cassette grille and main unit after installing the CASSETTE GRILLE.
Choose the minimum temperature
between cooling and heating
settings (deadband) for Dual
setpoint auto mode (set in No. 68).
07 7°F (3.5°C)
08 8°F (4.0°C)
09 9°F (4.5°C)
(Forbidden)
70
00
Temperature conditions when the external heater is ON
Temperature (t) when the external heater is ON= Room temperature - set temperature
Set value of function: 61
Set value of function: 62
00
00
01
t < -5.4°F (-3°C)
02
03
04
t ≤ -0.9°F (-0.5°C)
01
t < -3.6°F (-2°C)
t ≤ -1.8°F (-1°C)
02
t < -3.6°F (-2°C)
t ≤ -3.6°F (-2°C)
03
t < -5.4°F (-3°C)
t ≤ -5.4°F (-3°C)
04
t < -7.2°F (-4°C)
t ≤ -7.2°F (-4°C)
05
t < -9.0°F (-5°C)
t ≤ -9.0°F (-5°C)
En-12
9371022574-02_IM.indb 12
2018/1/26 10:22:00
11. ERROR CODES
If you use a wired type remote controller, error codes will appear on the remote controller
display. If you use a wireless remote controller, the lamp on the photodetector unit will
output error codes by way of blinking patterns. See the lamp blinking patterns and error
codes in the table below.
OPERATION
lamp (green)
Error indications
TIMER lamp FILTER lamp
(orange)
(red)
Wired Remote
Controller Error
code
Error contents
(1)
(2)
Remote controller communication error
(1)
(4)
Network communication error
(1)
(6)
Peripheral unit communication error
(2)
(6)
Indoor unit address setting error
(2)
(9)
Connection unit number
error in wired remote
controller system
(3)
(1)
Indoor unit power supply
abnormal
(5)
(1)
Indoor unit main PCB
error
(3)
(10)
Indoor unit communication circuit (wired remote
controller) error
(4)
(1)
Indoor unit room temp.
thermistor error
(4)
(2)
Indoor unit heat ex.
temp. thermistor error
(4)
(4)
Human sensor error
(5)
(1)
Indoor unit fan motor
1 error
(5)
(2)
Indoor unit coil (expansion valve) error
(5)
(3)
Indoor unit water drain
abnormal
(9)
(15)
Outdoor unit miscellaneous error
(10)
(8)
Poor refrigerant circulation
(13)
(1)
RB unit error
Display mode
: 0.5 s ON / 0.5 s OFF
: 0.1 s ON / 0.1 s OFF
( ) : Number of flashing
Wired Remote Controller Display
UTY-RNRUZ* (2-wire type)
Touch the [Next Page] (or [previous page])
to switch to other indoor unit information.
Error icon
Fri 10:00AM
Mode
Set Temp.
Fan
Status
Page 1/ 4
Air Flow Direction
VT
HZ
1
Individual
Economy
Unoccupied
Status
Menu
Touch the [Status].
3
Anti Freeze
Off
Monitor
Off
Next
Page
Error
Information
Touch the [Error Information].
2-digit numbers are corresponding to
the error code in the preceding table.
For more information, refer to the installation manual of the remote controller.
En-13
9371022574-02_IM.indb 13
2018/1/26 10:22:00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement