Fujitsu AUXA30GALH Installation Manual

Fujitsu AUXA30GALH Installation Manual
INNENGERÄT (Kassettentyp)
Nur für autorisiertes Fachpersonal.
MANUEL D’INSTALLATION
UNITÉ INTÉRIEURE (type cassette)
Pour le personnel agréé uniquement.
MANUAL DE INSTALACIÓN
UNIDAD INTERIOR (Tipo casete)
Únicamente para personal de servicio autorizado.
MANUALE DI INSTALLAZIONE
UNITÀ INTERNA (tipo a cassetta)
Μόνο για εξουσιοδοτημένο τεχνικό προσωπικό.
MANUAL DE INSTALAÇÃO
UNIDADE INTERIOR (Tipo Cassete)
Apenas para técnicos autorizados.
РУКОВОДСТВО ПО УСТАНОВКЕ
ВНУТРЕННИЙ МОДУЛЬ (кассетного типа)
Только для авторизованного обслуживающего персонала.
MONTAJ KILAVUZU
İÇ ÜNİTE (Kaset Tipi)
Português
ΕΣΩΤΕΡΙΚΗ ΜΟΝΑΔΑ (Τύπος Κασέτας)
Русский
ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ
Ελληνικά
A uso esclusivo del personale tecnico autorizzato.
Türkçe
AUXD18GALH
AUXD24GALH
AUXA18GALH
AUXA24GALH
AUXA30GALH
AUXA34GALH
AUXA36GALH
AUXA45GALH
AUXA54GALH
Deutsch
INSTALLATIONSANLEITUNG
Français
For authorized service personnel only.
Español
INDOOR UNIT (Cassette Type)
Italiano
INSTALLATION MANUAL
English
TM
Yalnızca yetkili servis personeli için.
Refer to the rating label for the serial number,
manufactured year and month.
MADE IN P.R.C.
[Original instructions]
PART NO. 9371022383-03
9371022383-03_IM.indb 1
2017/8/11 15:11:20
INSTALLATION MANUAL
PART NO. 9371022383-03
VRF system indoor unit (Cassette type)
Do not attempt to install the air conditioner or a part of the air conditioner by yourself.
1.
SAFETY PRECAUTIONS .........................................................................................1
2.
ABOUT THIS PRODUCT..........................................................................................1
2.1. Precautions for using the R410A refrigerant ......................................................1
2.2. Special tool for R410A .......................................................................................1
2.3. Accessories .......................................................................................................2
2.4. Optional parts ....................................................................................................2
INSTALLATION WORK ............................................................................................2
3.1. Selecting an installation location .......................................................................2
3.2. Installation dimensions ......................................................................................3
3.3. Installing the unit ................................................................................................3
4.
PIPE INSTALLATION ...............................................................................................5
4.1. Selecting the pipe material ................................................................................5
4.2. Pipe requirement ...............................................................................................5
4.3. Flare connection (pipe connection) ...................................................................5
4.4. Installing heat insulation ....................................................................................6
5.
INSTALLING DRAIN PIPES .....................................................................................6
6.
ELECTRICAL WIRING .............................................................................................7
6.1. Electrical requirement ........................................................................................8
6.2. Wiring method ...................................................................................................8
6.3. Unit wiring ..........................................................................................................8
6.4. Connection of wiring ..........................................................................................9
6.5. External input and external output (Optional parts) ...........................................10
7.
This mark indicates procedures which, if improperly performed,
might possibly result in personal harm to the user, or damage
to property.
Read carefully all security information before use or install the air conditioner.
Contents
3.
CAUTION
FIELD SETTING .......................................................................................................12
7.1. Setting the address ............................................................................................12
7.2. Custom code setting ..........................................................................................13
7.3. Function setting .................................................................................................14
8.
CASSETTE GRILLE INSTALLATION .......................................................................15
9.
TEST RUN ................................................................................................................15
9.1. Test run using Outdoor unit (PCB) .....................................................................15
9.2. Test run using Remote Controller ......................................................................15
10. CHECK LIST.............................................................................................................15
11. ERROR CODES .......................................................................................................16
This unit must be installed by qualified personnel with a capacity certificate for handling
refrigerant fluids. Refer to regulation and laws in use on installation place.
The installation must be carried out in compliance with regulations in force in the place
of installation and the installation instructions of the manufacturer.
This unit is part of a set constituting an air conditioner. It must not be installed alone or
with non-authorized by the manufacturer.
Always use a separate power supply line protected by a circuit breaker operating on all
wires with a distance between contact of 3mm for this unit.
The unit must be correctly earthed (grounded) and the supply line must be equipped
with a differential breaker in order to protect the persons.
The units are not explosion proof and therefore should not be installed in explosive
atmosphere.
Never touch electrical components immediately after the power supply has been turned
off. Electric shock may occur. After turning off the power, always wait 5 minutes before
touching electrical components.
This unit contains no user-serviceable parts. Always consult authorized service personnel to repairs.
When moving, consult authorized service personnel for disconnection and installation
of the unit.
2. ABOUT THIS PRODUCT
2.1. Precautions for using the R410A refrigerant
WARNING
Do not introduce any substance other than the prescribed refrigerant into the
refrigeration cycle.
If air enters the refrigeration cycle, the pressure in the refrigeration cycle will become
abnormally high and cause the piping to rupture.
If there is a refrigerant leakage, make sure that it does not exceed the concentration
limit.
If a refrigerant leakage exceeds the concentration limit, it can lead to accidents such
as oxygen starvation.
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
area. Touching the refrigerant directly can cause frostbite.
If a refrigerant leakage occurs during operation, immediately vacate the premises and
thoroughly ventilate the area.
If the refrigerant comes in contact with a flame, it produces a toxic gas.
2.2. Special tool for R410A
1. SAFETY PRECAUTIONS
WARNING
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information
pertaining to your safety. Be sure to observe them.
• Hand this Manual, together with the Operating Manual to the customer.
Request the customer to keep them on hand for future use, such as for relocating or
repairing the unit.
WARNING
This mark indicates procedures which, if improperly
performed, might lead to the death or serious injury of the
user.
Request your dealer or a professional installer to install the unit in accordance with
this Manual.
An improperly installed unit can cause serious accidents such as water leakage,
electric shock, or fire.
If the unit is installed in disregard of the instructions in the Installation Manual, it will
void the manufacturer’s warranty.
Do not turn ON the power until all work has been completed.
Turning ON the power before the work is completed can cause serious accidents
such as electric shock or fire.
To install a unit that uses the R410A refrigerant, use dedicated tools and piping
materials that have been manufactured specifically for R410A use.
Because the pressure of the R410A refrigerant is approximately 1.6 times higher
than the R22, failure to use dedicated piping material or improper installation can
cause rupture or injury.
Furthermore, it can cause serious accidents such as water leakage, electric shock,
or fire.
Tool name
Gauge manifold
Pressure is huge and cannot be measured with a conventional
(R22) gauge. To prevent erroneous mixing of other refrigerants,
the diameter of each port has been changed.
It is recommended to use a gauge manifold with a high pressure
display range –0.1 to 5.3 MPa and a low pressure display range
–0.1 to 3.8 MPa.
Charging hose
To increase pressure resistance, the hose material and base
size were changed.
Vacuum pump
A conventional (R22) vacuum pump can be used by installing
a vacuum pump adapter. Be sure that the pump oil does not
backflow into the system. Use one capable for vacuum suction
of –100.7 kPa (5 Torr, –755 mmHg).
If refrigerant leaks while work is being carried out, ventilate the area.
If the refrigerant comes in contact with a flame, it produces a toxic gas.
Installation work must be performed in accordance with national wiring standards by
authorized personnel only.
Except for EMERGENCY, never turn off main as well as sub breaker of the indoor
units during operation. It will cause compressor failure as well as water leakage.
First, stop the indoor unit by operating the control unit, converter or external input
device and then cut the breaker. Make sure to operate through the control unit,
converter or external input device. When the breaker is designed, locate it at a place
where the users cannot start and stop in the daily work.
Contents of change
Gas leakage
detector
Special gas leakage detector for HFC refrigerant R410A.
En-1
9371022383-03_IM.indb 1
2017/8/11 15:11:20
2.3. Accessories
2.4. Optional parts
Description
WARNING
For installation purposes, be sure to use the parts supplied by the manufacturer or
other prescribed parts.
The use of non-prescribed parts can cause serious accidents such as the unit to fall,
water leakage, electric shock, or fire.
The following installation parts are furnished. Use them as required.
External connect kit
Keep the Installation Manual in a safe place and do not discard any other
accessories until the installation work has been completed.
Name and Shape
Q’ty
Application
Model
Application
UTY-XWZXZC
For output function
(Output terminal / CNB01)
UTY-XWZXZB
For control input function
(Apply voltage terminal / CNA01)
UTY-XWZXZD
For control input function
(Dry contact terminal / CNA02)
UTY-XWZXZ7
For forced thermostat off function
(Apply voltage terminal / CNA03)
UTY-XWZXZE
For forced thermostat off function
(Dry contact terminal / CNA04)
UTZ-KXRA, UTZ-KXGA
Operation manual
1
Insulation kit for high
humidity
(This book)
Installation manual
(For indoor unit height
298 mm)
UTZ-KXGB
(For indoor unit height
256 mm)
Install when the condition under the
roof is over 80% in humidity and over
30°C in temperature.
1
3. INSTALLATION WORK
Cable tie (Large)
For fixing the connection
pipe (Large and Small)
4
Cable tie (Medium)
Correct initial installation location is important because it is difficult to move unit after it is
installed.
3.1. Selecting an installation location
For transmission and remote
controller cable binding.
2
WARNING
Select installation locations that can properly support the weight of the indoor. Install
the units securely so that they do not topple or fall.
CAUTION
Coupler heat insulation
(Small)
For indoor side pipe joint (Small)
1
Coupler heat insulation
(Large)
For indoor side pipe joint (Large)
1
Template
(Carton top)
For installing indoor unit.
Do not install the unit in the following areas:
• Area with high salt content, such as at the seaside.
It will deteriorate metal parts, causing the parts to fail or the unit to leak water.
• Area filled with mineral oil or containing a large amount of splashed oil or steam,
such as a kitchen.
It will deteriorate plastic parts, causing the parts to fail or the unit to leak water.
• Area that generates substances that adversely affect the equipment, such as sulfuric
gas, chlorine gas, acid, or alkali.
It will cause the copper pipes and brazed joints to corrode, which can cause
refrigerant leakage.
• Area that can cause combustible gas to leak, contains suspended carbon fibers or
flammable dust, or volatile inflammables such as paint thinner or gasoline.
If gas leaks and settles around the unit, it can cause a fire.
• Area where animals may urinate on the unit or ammonia may be generated.
Do not use the unit for special purposes, such as storing food, raising animals,
growing plants, or preserving precision devices or art objects.
It can degrade the quality of the preserved or stored objects.
1
Do not install where there is the danger of combustible gas leakage.
For installing indoor unit.
Washer
Do not install the unit near a source of heat, steam, or flammable gas.
Install the unit where drainage does not cause any trouble.
8
For installing drain pipe
Insulation
If children under 10 years old may approach the unit, take preventive measures so
that they cannot reach the unit.
1
Drain hose
Install the indoor unit, power supply cable, transmission cable, and remote controller
cable at least 1 m away from a television or radio receivers. The purpose of this is to
prevent TV reception interference or radio noise.
(Even if they are installed more than 1 m apart, you could still receive noise under
some signal conditions.)
For installing drain pipe
VP25 (O.D.32, I.D.25)
Use the “Insulation kit for high humidity” (option), when the condition under the roof
is over 80% in humidity and over 30°C in temperature. Otherwise, there is a risk of
condensation on the ceiling.
1
Decide the mounting position with the customer as follows:
Hose band
For installing drain hose
(1) Install the indoor unit on a place having a sufficient strength so that it withstands
against the weight of the indoor unit.
(2) The inlet and outlet ports should not be obstructed; the air should be able to blow all
over the room.
1
(3) Leave the space required to service the air conditioner.
(4) A place from where the air can be distributed evenly throughout the room by the unit.
For installing drain pipe
Drain pipe insulation
(5) Install the unit where connection to the outdoor unit (or RB unit) is easy.
(6) Install the unit where the connection pipe can be easily installed.
1
(7) Install the unit where the drain pipe can be easily installed.
(8) Install the unit where noise and vibrations are not amplified.
(9) Take servicing, etc., into consideration and leave the spaces. Also install the unit
where the filter can be removed.
En-2
9371022383-03_IM.indb 2
2017/8/11 15:11:20
3.3.1. Position the ceiling hole and hanging bolts
3.2. Installation dimensions
(1) Positions of the ceiling opening, hanging bolt pitch, piping and ducts. (unit: mm)
Ceiling height is as shown in the figure.
• Ceiling opening and hanging bolt pitch.
256 mm or more (AUXD18,24)
298 mm or more (AUXA18,24,30,34,36,54)
950 mm (Cassette grille)
20 to
45 mm
Strong and durable ceiling
20 to
45 mm
860 to 910 mm (Ceiling opening)
20 to
45 mm
840 mm (Indoor unit)
1,500 mm
or more
795 mm (Hanging bolt pitch)
Standard mode
3,000
3,000
3,200
3,200
3,200
3,200
3,200
3,200
3,200
High Ceiling mode
3,500
3,500
3,600
3,600
3,600
3,600
4,200
4,200
4,200
* Be sure to make the function settings with the remote controller according to the
installed ceiling height.
50 mm
130 mm
20 to
45 mm
AUXD AUXD AUXA AUXA AUXA AUXA AUXA AUXA AUXA
18
24
18
24
30
34
36
45
54
130 mm
H (mm)
Function setting
860 to 910 mm
(Ceiling opening)
H: Maximum height from floor to ceiling
130 mm
Obstruction
Floor
80 mm
699 mm
(Hanging bolt pitch)
1,000 mm or more
840 mm (Indoor unit)
1,800 mm to H
950 mm (Cassette grille)
3,000 mm or more
200 mm
Discharge Direction Setting
If the job is done with the panel frame only, there is a risk that the unit will come
loose. Please take care.
358 mm
278 mm
Gas pipe
60 mm
180 mm
Drain pipe
(Connect the attached
drain hose)
Liquid pipe
200 mm
WARNING
A
• Refrigerant piping and drain piping positions.
Drain pipe
Install the air conditioner in a location which can withstand a load of at least 5 times
the weight of the main unit and which will not amplify sound or vibration. If the
installation location is not strong enough, the indoor unit may fall and cause injuries.
B
246
288
140 mm
3.3. Installing the unit
A
256
298
80 mm
* Select the most appropriate airflow direction from 3 or 4 directions according to the
shape of the room and the installation position.
* When changing the number of outlets, we recommend using the optional AIR
OUTLET SHUTTER PLATE KIT to close the outlet.
* For the specific closing pattern, please refer to the attached AIR OUTLET SHUTTER
PLATE KIT’S MANUAL. (Do so before installing the cassette grille as it will be
installed on the body.)
Model
AUXD18/24
AUXA18/24/30/34/36/45/54
10 mm
100 mm or more
40 mm
B
10 mm
3 direction
140 to
145 mm
4 direction
50 to
100 mm
• The discharge direction can be selected as shown below.
En-3
9371022383-03_IM.indb 3
2017/8/11 15:11:20
3.3.2. Hanging preparations
• Distribution ducts and fresh air inlet positions.
Distribution duct connecting port
• Firmly fasten the hanging bolts as shown in the figure or by another method.
• Install the hanging bolts at a place where they would be capable of holding a weight of
at least 490 N per bolt.
Distribution duct connecting port
Distribution duct connecting port
Fresh air inlet position
Hole-in anchor
Hole-in plug Concrete
Hanging bolt M10
(locally purchased)
Distribution duct connecting port
3.3.3. Body installation
• Detailed diagram of distribution duct connecting port (4 sides)
100 mm
100 mm
(1) Install the attached washer and nut (prepared on site) onto the hanging bolt.
83 mm
90 mm
Cut out
(2) Hook the body onto the hanging bolt.
185 mm
83 mm
Insert
(3) Adjust the dimensions of the ceiling surface from the body.
After installing the cassette grille, you can make fine adjustment of the height of the
body. For details, refer to the installation manual of the cassette grille.
WARNING
Perform final tightening by tightening the double nut firmly.
352 mm
10 × Ø 2.5 mm hole
Be sure to install the body horizontally and adjust the height below the body and the
ceiling surface properly.
• Fresh air inlet position
Hanging bolt
(locally purchased)
250 mm
Burling hole pitch
Ø 70 mm
Cut out
185 mm
Ø 88 mm
Nut A
(locally purchased)
Washer
(Accessories)
30 mm or more
After installing the body,
tighten the nuts.
4 × Ø 2.5 mm hole
NOTE:
Conduct proper insulation when connecting the distribution ducts and fresh air inlet.
Insulation
Nut B (Double Nut)
(locally purchased)
Washer
(Accessories)
10 to 15 mm
3.3.4. Leveling
• Using a level, or vinyl hose filled with water, fine adjust so that the body is level.
• Inclined installation so as the drain pipe side is higher may cause a malfunction of the
float switch, and may cause water leakage.
Drain pipe
Fresh air inlet position
* When sucking in the fresh air, please detach the insulation affixed to the drain pan.
(2) Setting the positions of hanging bolt and ceiling opening.
• Use an installation template (packaging top surface) to set the positions of the hanging
bolt and ceiling opening and drill holes.
Vinyl hoses
(3) Hanging structure.
• Select a strong structure for the hanging location.
• If necessary, reinforce the hanging bolt with quakeproof columnar support material to
prevent shaking.
• Use hanging bolts of M8 to M10.
En-4
9371022383-03_IM.indb 4
2017/8/11 15:11:20
4.3. Flare connection (pipe connection)
4. PIPE INSTALLATION
WARNING
CAUTION
Be more careful that foreign matter (oil, water, etc.) does not enter the piping than
with refrigerant R410A models. Also, when storing the piping, securely seal the
openings by pinching, taping, etc.
While welding the pipes, be sure to blow dry nitrogen gas through them.
Tighten the flare nuts with a torque wrench using the specified tightening method.
Otherwise, the flare nuts could break after a prolonged period, causing refrigerant to
leak and generate hazardous gas if the refrigerant comes into contact with a flame.
4.3.1. Flaring
Use special flare tool exclusive for R410A.
4.1. Selecting the pipe material
(1) Cut the connection pipe to the necessary length with a pipe cutter.
(2) Hold the pipe downward so that cuttings will not enter the pipe and remove any burrs.
CAUTION
Do not use existing pipes from another refrigeration system or refrigerant.
Use pipes that have clean external and internal sides without any contamination
which may cause trouble during use, such as sulfur, oxide, dust, cutting waste, oil, or
water.
(3) Insert the flare nut (always use the flare nut attached to the indoor and outdoor units (or
RB unit) respectively) onto the pipe and perform the flare processing with a flare tool.
Use the special R410A flare tool. Leakage of refrigerant may result if other flare nuts
are used.
(4) Protect the pipes by pinching them or with tape to prevent dust, dirt, or water from
entering the pipes.
It is necessary to use seamless copper pipes.
Material : Phosphor deoxidized seamless copper pipes
It is desirable that the amount of residual oil is less than 40 mg/10 m.
Do not use copper pipes that have a collapsed, deformed, or discolored portion
(especially on the interior surface). Otherwise, the expansion valve or capillary tube
may become blocked with contaminants.
Check if [L] is flared uniformly and
is not cracked or scratched.
B
Die
A
L
Pipe
Improper pipe selection will degrade performance. As an air conditioner using
R410A incurs pressure higher than when using conventional (R22) refrigerant, it is
necessary to choose adequate materials.
• Thicknesses of copper pipes used with R410A are as shown in the table.
• Never use copper pipes thinner than those indicated in the table even if they are
available on the market.
Thicknesses of Annealed Copper Pipes (R410A)
Pipe outside diameter
[mm (in)]
Dimension A [mm]
Flare tool for R410A, clutch
type
0
Dimension B-0.4 [mm]
6.35 (1/4)
9.1
9.52 (3/8)
13.2
0 to 0.5
Pipe outside diameter [mm (in)]
Thickness [mm]
12.70 (1/2)
6.35 (1/4)
0.80
15.88 (5/8)
19.7
9.52 (3/8)
0.80
19.05 (3/4)
24.0
12.70 (1/2)
0.80
15.88 (5/8)
1.00
19.05 (3/4)
1.20
When using conventional (R22) flare tools to flare R410A pipes, the dimension A should
be approximately 0.5 mm more than indicated in the table (for flaring with R410A flare
tools) to achieve the specified flaring. Use a thickness gauge to measure the dimension A.
It is recommended that a R410A flaring tool is used.
Width across
flats
4.2. Pipe requirement
16.6
Pipe outside diameter
[mm (in)]
Width across flats of Flare nut
[mm]
6.35 (1/4)
17
CAUTION
Refer to the installation manual for the outdoor unit for description of allowable pipe
length and height difference.
Use pipe with water-resistant heat insulation.
9.52 (3/8)
22
12.70 (1/2)
26
15.88 (5/8)
29
19.05 (3/4)
36
CAUTION
Install heat insulation around both the gas and liquid pipes. Failure to do so may
cause water leaks.
Use heat insulation with heat resistance above 120 °C. (Reverse cycle model only)
In addition, if the humidity level at the installation location of the refrigerant piping
is expected to exceed 70 %, install heat insulation around the refrigerant piping.
If the expected humidity level is 70 to 80 %, use heat insulation that is 15 mm or
thicker and if the expected humidity exceeds 80 %, use heat insulation that is 20 mm
or thicker. If heat insulation is used that is not as thick as specified, condensation
may form on the surface of the insulation. In addition, use heat insulation with heat
conductivity of 0.045 W/(m·K) or less (at 20 °C).
4.3.2. Bending pipes
• If pipes are shaped by hand, be careful not to collapse them.
• Do not bend the pipes in an angle more than 90°.
• When pipes are repeatedly bend or stretched, the material will harden, making it
difficult to bend or stretch them any more.
• Do not bend or stretch the pipes more than 3 times.
CAUTION
To prevent breaking of the pipe, avoid sharp bends.
If the pipe is bent repeatedly at the same place, it will break.
En-5
9371022383-03_IM.indb 5
2017/8/11 15:11:20
4.3.3. Pipe connection
5. INSTALLING DRAIN PIPES
CAUTION
Be sure to install the pipe against the port on the indoor unit and the outdoor unit
correctly. If the centering is improper, the flare nut cannot tightened smoothly. If the
flare nut is forced to turn, the threads will be damaged.
Do not remove the flare nut from the indoor unit pipe until immediately before
connecting the connection pipe.
Do not use mineral oil on flared part. Prevent mineral oil from getting into the system
as this would reduce the lifetime of the units.
Hold the torque wrench at its grip, keeping it at a right angle with the pipe, in order to
tighten the flare nut correctly.
(1) Detach the caps and plugs from the pipes.
(2) Center the pipe against the port on the indoor unit, and then turn the flare nut by
hand.
Connection pipe (Gas)
WARNING
Do not insert the drain piping into the sewer where sulfurous gas occurs. (Heat
exchange erosion may occur)
Insulate the parts properly so that water will not drip from the connection parts.
Check for proper drainage after the construction by using the visible portion of
transparent drain port and the drain piping final outlet on the body.
CAUTION
Do not apply adhesive agent on the drain port of the body. (Use the attached drain
hose and connect the drain piping)
• Install the drain pipe with downward gradient (1/100 to 1/50) and so there are no rises
or traps in the pipe. Unsmooth draining caused by accumulated water flow in the pipe
may cause clogged drain.
• Use general hard polyvinyl chloride pipe (VP25) [outside diameter 32 mm].
Connection pipe
(Liquid)
• When the pipe is long, install supporters.
• Do not perform air bleeding. Drainage may be blown out.
• Always heat insulate the indoor side of the drain pipe.
• If it is impossible to have sufficient gradient of pipe, perform drain lift-up.
Pipe size
Drain pipe
VP25 (O.D. 32 mm)
(3) When the flare nut is tightened properly by your hand, hold the body side coupling
with a separate spanner, then tighten with a torque wrench. (See the table below for
the flare nut tightening torques.)
Hanging fittings
1.5 to 2 m
Tighten with 2 wrenches.
Holding wrench
VP25 (O.D. 32 mm)
Downward gradient 1/100 to 1/50
Flare nut
Torque wrench
PROHIBITED:
Indoor unit pipe
(Body side)
Connection pipe
Flare nut [mm (in)]
Tightening torque [N·m (kgf·cm)]
6.35 (1/4) dia.
16 to 18 (160 to 180)
9.52 (3/8) dia.
32 to 42 (320 to 420)
12.70 (1/2) dia.
49 to 61 (490 to 610)
15.88 (5/8) dia.
63 to 75 (630 to 750)
19.05 (3/4) dia.
90 to 110 (900 to 1,100)
Rise
Trap
Air bleeding
When lifting up drain:
• Height of inclined pipe should be less than 850 mm from the ceiling. A rise dimension
over this range will cause leakage.
• Lift up the pipe vertically at the position of 300 mm or less from the unit.
Downward gradient
300 mm or less
1/100 to 1/50
VP25 (O.D. 32 mm)
local arrangement
850 mm or less
4.4. Installing heat insulation
Horizontal or
upward gradient
CAUTION
After checking for gas leaks (refer to the Installation Manual of the outdoor unit),
perform this section.
Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to
do so may cause water leaks.
850 mm or less
VP30 (O.D. 38 mm) or more
Downward gradient 1/100 to 1/50
After checking for gas leaks, insulate by wrapping insulation around the 2 parts (gas and
liquid) of the indoor unit coupling, using the Coupler heat insulation.
After installing the Coupler heat insulation, wrap both ends with vinyl tape so that there is
no gap.
Cable tie (Large)
(Accessories)
Coupler heat
insulation
(Accessories)
No gap
Body
Be sure to overlap
the insulation
Coupler heat
insulation
CAUTION
Must fit tightly against body without any gap.
En-6
9371022383-03_IM.indb 6
2017/8/11 15:11:21
Working procedure
(1) Install the attached drain hose to the drain port of the body. Install the hose band from
the top of the hose within the graphic display area. Secure firmly with the hose band.
(2) Use vinyl adhesive agent to glue the drain piping (PVC pipe VP25) which is prepared
on site or elbow socket.
(Apply color adhesive agent evenly until the gauge line and seal)
(4) Install the heat insulation.
(5) Use the attached heat insulation to insulate the drain port and band parts of the body.
Attached hose band
(Accessories)
Locally arranged
vinyl pipe
Attached drain hose
heat insulation
(Accessories)
WARNING
Electrical work must be performed in accordance with this Manual by a person
certified under the national or regional regulations. Be sure to use a dedicated circuit
for the unit.
An insufficient power supply circuit or improperly performed electrical work can cause
serious accidents such as electric shock or fire.
(3) Check the drainage. (See separate diagram)
Install the knob
faces upward
6. ELECTRICAL WIRING
Before starting work, check that power is not being supplied to the all units.
For wiring, use the prescribed type of cables, connect them securely, making sure
that there are no external forces of the cables applied to the terminal connections.
Improperly connected or secured cables can cause serious accidents such as
overheating the terminals, electric shock, or fire.
Securely install the electrical box cover on the unit.
An improperly installed electrical box cover can cause serious accidents such as
electric shock or fire through exposure to dust or water.
Attached drain hose
(Accessories)
Attached heat insulation
(Accessories)
Install sleeves into any holes made in the walls for wiring. Otherwise, a short circuit
could result.
Use the included connection cables and power cables or ones specified by the
manufacturer. Improper connections, insufficient insulation, or exceeding the
allowable current can cause electric shock or fire.
Do not modify the power cables, use extension cables, or use any branches in the
wiring. Improper connections, insufficient insulation, or exceeding the allowable
current can cause electric shock or fire.
Match the terminal block numbers and connection cable colors with those of the
outdoor unit (or RB unit). Erroneous wiring may cause burning of the electric parts.
Securely connect the connection cables to the terminal board. In addition, secure the
cables with wiring holders. Improper connections, either in the wiring or at the ends
of the wiring, can cause a malfunction, electric shock, or fire.
(a) Top view
(b) Side view
VP25
Applying area
of adhesive
35 mm
Hose Band
Always fasten the outside covering of the connection cable with the cable clamp. (If
the insulator is chafed, electric discharge may occur.)
Install an earth leakage breaker. In addition, install the earth leakage breaker so
that the entire AC main power supply is cut off at the same time. Otherwise, electric
shock or fire could result.
Always connect the earth (ground) cable.
Improper earthing (grounding) work can cause electric shocks.
Install the remote controller cables so as not to be direct touched with your hand.
5 to 10 mm
Gauge line
4 mm or less
20 mm
(c) Top view
(d) Hose opening view
Wind the attached heat insulation
around the hose band
Make sure the
alignment is on top
Perform wiring work in accordance with standards so that the air conditioner can be
operated safely and positively.
Connect the connection cable firmly to the terminal board. Imperfect installation may
cause a fire.
If the supply cable is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
CAUTION
Earth (Ground) the unit.
Do not connect the earth (ground) cable to a gas pipe, water pipe, lightning rod, or a
telephone earth (ground) cable.
Improper earthing (grounding) may cause electric shock.
Make sure there are no gaps
NOTE: Check for drainage
Pour about 1 liter of water from the position shown in the diagram or from the airflow
outlet to the dew tray. Check for any abnormalities such as strange noises and whether
the drain pump functions normally.
Do not connect power supply cables to the transmission or remote controller terminals,
as this will damage the product.
Never bundle the power supply cable and transmission cable, remote control cable
together. Separate these cable by 50 mm or more. Bundling these cables together will
cause miss operation or breakdown.
When handling PCB, static electricity charged in the body may cause malfunction of the
PCB. Follow the cautions below:
• Establish an earth (ground) for the indoor and outdoor units and peripheral devices.
• Cut power (breaker) off.
• Touch metal part of the indoor units for more than 10 seconds to discharge static
electricity charged in the body.
• Do not touch terminals of parts and patterns implemented on PCB.
En-7
9371022383-03_IM.indb 7
2017/8/11 15:11:21
6.1. Electrical requirement
6.2. Wiring method
Voltage rating
230 V
198 to 264 V (50 Hz)
198 to 253 V (60 Hz)
Operating range
• Select the power cable type and size in accordance with relevant local and national
regulations.
• Specifications for local wiring power cord and branch wiring are in compliance with local
code.
• Max. wire length: Set a length so that the voltage drop is less than 2%. Increase the wire
diameter when the wire length is long.
Breaker should be installed at every refrigerant system. Do not use a breaker in a different
refrigerant system.
Refer to the table for the breaker specifications of each installation condition. Perform
the power crossover wiring within the range of the same refrigerant system. When the
crossover wiring is done, make a connection for indoor units to satisfy conditions A and B
below.
A. Current breaker requirements
Example
Outdoor unit or RB unit *1
Transmission
Indoor unit
Transmission
*2
Power supply
Indoor unit
Remote
control
*2
*3
Breaker
Model
MCA
AUXD18GALH
0.32 A
AUXD24GALH
0.38 A
AUXA18GALH
0.46 A
AUXA24GALH
0.46 A
AUXA30GALH
0.51 A
AUXA34GALH
0.61 A
AUXA36GALH
0.64 A
AUXA45GALH
0.83 A
AUXA54GALH
0.94 A
Indoor unit
*2
*3
Breaker
*3
Breaker
MFA
Power supply
20 A
Remote controller
(Master)
Remote controller
(Slave)
Remote controller
*1: When connecting to the Heat Recovery System, refer to the installation manual of the
RB unit.
*2: Earth (Ground) the remote controller if it has an earth (ground) cable.
*3: When connecting the 2-wire type remote controller, Y3 is not used.
(Crossover wiring of power supply)
Indoor unit
Indoor unit
Power supply
MCA: Minimum Circuit Ampacity
MFA: Maximum Fuse Ampacity
Power supply
Indoor unit
Power supply
Pull box
When the power crossover wiring is done, make it so that the total of the MCA of the
connected RB units and indoor units does not exceed the 15 A. For RB unit MCA, refer to
the RB unit installation manual.
If the capacity of connected RB units and indoor units exceeds the upper limit, either add
breakers or use a breaker with a greater capacity.
B. Earth leakage breaker requirements
Breaker capacity
* Maximum connectable “indoor units” or
“indoor units + RB units”
30 mA, 0.1 sec or less
44 or less
100 mA, 0.1 sec or less
45 to 148 **
Breaker
Pull box
Power supply
6.3. Unit wiring
• Before attaching the cable to terminal block.
6.3.1. Power supply cable
* Heat pump type: indoor units, Heat recovery type: indoor units and RB units.
** If the 100 mA capacity breaker is not provided, split the quantity of the indoor units into
small groups of 44 units or less and provide a breaker with capacity of 30 mA for each
group.
20 mm
Earth (Ground)
cable
30 mm
6.1.1. Cable specifications
Recommended cable
2
size (mm )
Power supply cable
Transmission cable
Remote controller
cable (2-wire type)
Remote controller
cable (3-wire type)
A. For solid core wiring
Cable type
2.5
Type60245
IEC57 or
equivalent
0.33
LONWORKS
compatible cable
0.33 to 1.25
0.33
Sheathed PVC
cable*
Sheathed PVC
cable*
Remark
2 Cable + earth (ground)
22 AWG LEVEL 4
(NEMA)
non-polar 2 core,
twisted pair solid core
diameter 0.65 mm
Non-polar 2 core,
twisted pair
(1) To connect the electrical terminal, follow the below diagram and connect after looping
it around the end of the cable.
(2) Use the specified cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(3) Use an appropriate screwdriver to tighten the terminal screws.
Do not use a screwdriver that is too small, otherwise, the screw heads may be
damaged and prevent the screws from being properly tightened.
(4) Do not tighten the terminal screws too much, otherwise, the screws may break.
(5) See the table for the terminal screw tightening torques.
(6) Please do not fix 2 power supply cables with 1 screw.
Polar 3 core
*: Use shielded cable in accordance with local rules for remote controller cables.
Strip 25 mm
Loop
Cable
Screw with
special washer
Screw with
special washer
Cable end (Loop)
Cable end (Loop)
Terminal block
Cable
Do not apply branch wiring. It may result electric shock or fire.
En-8
9371022383-03_IM.indb 8
2017/8/11 15:11:21
WARNING
Tightening torque
When using solid core cables, do not use the ring terminal. If you use the solid core
cables with the ring terminal, the ring terminal's pressure bonding may malfunction
and cause the cables to abnormally heat up.
M3 screw (Transmission / X1, X2)
(Remote controller / Y1, Y2, Y3)
0.5 to 0.6 N·m
(5 to 6 kgf·cm)
CAUTION
B. For strand wiring
(1) Use ring terminals with insulating sleeves as shown in the figure below to connect to
the terminal block.
(2) Securely clamp the ring terminals to the cables using an appropriate tool so that the
cables do not come loose.
(3) Use the specified cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
To peel the film from the lead cable, use a dedicated tool that will not damage the
conductor cable.
When installing a screw on the terminal block, do not cut the cable by overtightening
the screw. On the other hand, an undertightened screw can cause faulty contact,
which will lead to a communication failure.
6.4. Connection of wiring
(4) Use an appropriate screwdriver to tighten the terminal screws.
Do not use a screwdriver that is too small, otherwise, the screw heads may be
damaged and prevent the screws from being properly tightened.
(5) Do not tighten the terminal screws too much, otherwise, the screws may break.
(6) See the table for the terminal screw tightening torques.
(1) Remove the control box cover and install each connection cable.
* Fill the wiring connecting port and remote
controller connecting port with putty or
heat insulation so that insects or dust will
not enter the unit.
(7) Please do not fix 2 power supply cables with 1 screw.
Ring terminal
Strip 10 mm
* Wiring connecting port
For putting through the
power supply cable.
Sleeve
Screw with
special washer
Cable
Connection cable clamp
Screw with
special washer
Ring terminal
Ring terminal
Terminal block
Cable
1 Wiring cover
WARNING
Use ring terminals and tighten the terminal screws to the specified torques,
otherwise, abnormal overheating may be produced and possibly cause heavy
damage inside the unit.
Power terminal board
2 Control box cover
Tightening torque
M4 screw
(Power supply / L, N, GND)
1.2 to 1.8 N·m
(12 to 18 kgf·cm)
Transmission cable and Remote
controller terminal board
* Remote controller connecting port
6.3.2. Transmission and Remote controller cable
Transmission cable
Shielded cable (no film)
For putting through the transmission
cable and the remote controller cable.
30 mm
(2) Please firmly tighten Connection cable and Remote controller cable with the attached
cable tie.
40 mm
Remote controller cable
For 3-wire type
For 2-wire type
30 mm
30 mm
• Connect remote controller and transmission cables as shown in Fig. C.
Fig. C
GOOD
PROHIBITED
Different diameter
Connect to 1 side
WARNING
Tighten the terminal screws to the specified torques, otherwise, abnormal
overheating may be produced and possibly cause heavy damage inside the unit.
En-9
9371022383-03_IM.indb 9
2017/8/11 15:11:21
CAUTION
6.5. External input and external output (Optional parts)
When switching the DIP switch (SW1), be sure to turn off the power supply to the
indoor unit. Otherwise, the PC board of the indoor unit may be damaged.
Controller PCB
DIP switch
(SET 2)
Apply voltage terminal
(CNA03)
OFF ON
SW1
SW2
SW3
SW4
(CNA01)
Cable clamp
L, N:
Power supply
cable
Output terminal
(CNB01)
Earth (ground)
(CNA02)
Dry contact terminal
(CNA04)
(1) External input
• Indoor unit can be Operation/Stop, Emergency stop or Forced stop by using indoor unit
PCB CNA01 or CNA02.
• “Operation/Stop” mode, “Emergency stop” mode or “Forced stop” mode can be selected
with function setting of indoor unit.
• Indoor unit can be Forced thermostat off by using indoor unit PCB CNA03 or CNA04.
• A twisted pair cable (22 AWG) should be used. Maximum length of cable is 150 m.
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• The wire connection should be separate from the power cable line.
X1, X2:
Transmission cable
Input select
Cable tie (Medium)
(Accessories)
● Apply voltage terminal ([CNA01], [CNA03])
Use either one of these types of terminal according to the application. (Both types of
terminals cannot be used simultaneously.)
When a power supply must be provided at the input device you want to connect, use the
Apply voltage terminal ([CNA01], [CNA03]).
Y1,Y2,Y3:
Remote controller
cable
Input
device 1
For 2-wire type
Input
device 2
DIP switch (SW1)
Load
resistance
*a
Load
resistance
*a
Input
device 3
DC power supply *1
12 to 24V
Load
resistance
*a
CNA01
For 3-wire type
Connect the remote
controller cable
Y1: Non-polar
Y2: Non-polar
Y3: Do not connect *1
Y1: Red
Y2: White
Y3: Black
Set the DIP switch (SW1)
2WIRE (Factory setting)
3WIRE
*1: If you connect the remote controller cable to the terminal Y3, 2-wire type
remote controller does not work.
P.C.B
*b
(3) Please fix the Connection cable with cable Clamp. And then install the Wire Cover with
screws.
CNA03
connected unit
*1 Make the power supply DC12 to 24V. Select a power supply capacity with an ample
surplus for the connected load.
Do not impress a voltage exceeding 24V across pins 1-2, and 1-3.
*a The allowable current is DC 5mA to 10mA. (Recommended: DC5mA)
Provide a load resistance such that the current becomes DC10mA or less.
Select very low current use contacts (usable at DC12V, DC1mA or less).
*b The polarity is [+] for pin 1 and [-] for pin 2 and 3. Connect correctly.
(c)
Bind securely
When connected to Apply voltage terminals of multiple indoor units with a connected unit,
be sure to make a branch outside the indoor unit using a pull box, etc. as shown on below
example.
CNA01
P.C.B
CNA01
connected unit
P.C.B
CNA01
Indoor unit
Do not bundle the remote controller cable, or wire the remote controller cable in
parallel, with the indoor unit connection wire (to the outdoor unit) and the power
supply cable. It may cause erroneous operation.
Load
resistance
P.C.B
Indoor unit
CAUTION
Input
device 1
(4) Install control box cover.
Load
resistance
Input
device 2
DC power supply
12 to 24V
Indoor unit
Detail (c)
En-10
9371022383-03_IM.indb 10
2017/8/11 15:11:21
[In the case of “Pulse” input]
● Dry contact terminal ([CNA02], [CNA04])
When a power supply is unnecessary at the input device you want to connect, use the Dry
contact terminal ([CNA02], [CNA04]).
P.C.B
Connector
Input signal
Command
Ch1
OFF → ON
Emergency stop
Ch2
OFF → ON
Normal
CNA01 or CNA02
CNA02
*c
*c
Ch 1
Ch 2
GND
* All indoor units of same refrigerant system stops when Emergency stop operates.
*d
● When function setting is “Forced stop” mode.
[In the case of “Edge” input]
Connector
Input signal
connected unit
*c Select very low current use contacts (usable at DC12V, DC1mA or less).
*d The wiring is different from Apply voltage terminals. Be sufficiently careful when wiring.
When connected to Dry contact terminals of multiple indoor units with a connected unit,
insulate each indoor unit with relay, etc. as shown on below example.
K5
CNA02
Indoor unit
Indoor unit
P.C.B
K2
P.C.B
K3
Input device 1
K6
CNA02
Input device 2
K1 - K6: Relay
(Device for DC Current)
NOTE :
When connected to multiple indoor units directly, it will cause breakdown.
Operation behavior
Edge
● Input signal type
The input signal type can be selected.
It is switched by DIP switch on the indoor unit PCB.
DIP switch [Set 2 SW2]
Edge
ON
Pulse
The width of pulse
must be longer than
200msec.
● When function setting is “Operation/Stop” mode.
Input signal
Command
OFF → ON
Operation
ON → OFF
Stop
Ch1 of CNA01 or CNA02
Ch2
OFF → ON
Normal
* When forced stop function is used with forming a remote controller group, connect the
same equipment to each indoor unit within the group.
• Selection method of functions
“Operation/Stop” mode or “Emergency stop” mode, “Forced stop” mode can be selected
with function setting of indoor unit.
● Forced thermostat off function
[“Edge” input only]
Connector
Input signal
Command
OFF → ON
Thermostat off
ON → OFF
Normal
Ch3 of CNA03 or CNA04
(2) External output
• A twisted pair cable (22AWG) should be used. Maximum length of cable is 25m.
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• Output voltage: Hi DC12V±2V, Lo 0V.
• Permissible current: 50mA
Output select
● When indicator etc. are connected directly
P.C.B
Error
indicator
CNB
01
Indoor unit Fan
status indicator
connected unit
Input signal
Command
Ch1
OFF → ON
Operation
Ch2
OFF → ON
Stop
CNA01 or CNA02
* The last command has priority.
* The indoor units within the same remote controller group operates in the same mode.
● When function setting is “Emergency stop” mode.
● When connecting with unit equipped with a power supply
P.C.B
Connected
device 1
Connected
device 2
Input signal
CNB
01
Connected
device 3
connected unit
[In the case of “Edge” input]
Connector
Forced stop
CNA01 or CNA02
[In the case of “Pulse” input]
Connector
Command
OFF → ON
Operation
indicator
[In the case of “Edge” input]
Connector
Input signal
Ch1
Pulse
Input signal type
OFF (Factory setting)
Normal
* When the forced stop is triggered, indoor unit stops and Operation/Stop operation by a
remote controller is restricted.
Indoor unit
Power supply for relay
CNA02
ON → OFF
[In the case of “Pulse” input]
Connector
K4
Forced stop
Ch1 of CNA01 or CNA02
P.C.B
K1
Command
OFF → ON
Relay (locally purchased)
Command
OFF → ON
Emergency stop
ON → OFF
Normal
Ch1 of CNA01 or CNA02
En-11
9371022383-03_IM.indb 11
2017/8/11 15:11:21
Operation behavior
Connector
CNB01
Fig. A
Output voltage
0V
External output1
Pins 1-2
DC 12 V
External output2
Pins 1-3
DC 12 V
External output3
Pins 1-4
DC 12 V
Status
Stop
Operation
0V
Normal
Error
0V
Indoor unit fan stop
Indoor unit fan operation
(3) Connection methods
Screw
• Wire modification
Remove insulation from wire attached to wire kit connector.
Remove insulation from locally purchased cable. Use crimp type insulated butt
connector to join field cable and wire kit wire.
Connect the wire with connecting wire with solder.
IMPORTANT: Be sure to insulate the connection between the wires.
Option parts
External input /output wire
Locally purchased
Cover
Rotary switch Example: “0”
Solder and insulate the connected parts.
• Connection terminals and wiring arrangement
Rotary switch
Example: “0”
In following figure, all the possible connectors are connected for description.
In actual installation, you cannot connect all the connectors at once.
Cable tie (locally purchased):
Bind to the transmission cable
hook
Setting
Indoor unit
address
Transmission cable
CNB01
CNA01
CNA03 CNA02
Setting range
0 to 63
Type of switch
Setting
example 2
IU AD × 10
IU AD × 1
REF AD × 10
REF AD × 1
CNA04
Refrigerant
circuit address
7. FIELD SETTING
There are 3 methods for address setting by FIELD SETTING as follows.
Set by either of the methods.
Each setting method is described (1) to (3) below.
(1) IU AD, REF AD SW settings ............. This section (7.1. Setting the address)
(2) Remote controller settings ............... Refer to the wired or wireless remote controller
manual for detailed setting information. (Set IU
AD, REF AD SW to 0)
(3) Automatic address settings ............. Refer to the outdoor unit manual for detailed
setting information. (Set IU AD, REF AD SW to 0)
CAUTION
Be sure to turn OFF the power before performing the field setting.
7.1. Setting the address
0 to 99
Setting
example
63
(1) Indoor unit address
Rotary switch (IU AD × 1)...Factory setting “0”
Rotary switch (IU AD × 10)...Factory setting “0”
When connecting multiple indoor units to 1 refrigerant system, set the address at IU
AD SW as shown in the Table A.
(2) Refrigerant circuit address
Rotary switch (IU AD × 1)...Factory setting “0”
Rotary switch (IU AD × 10)...Factory setting “0”
In the case of multiple refrigerant systems, set REF AD SW as shown in the Table
A for each refrigerant system.
Set to the same refrigerant circuit address as the outdoor unit.
• If working in an environment where the wireless remote controller can be used, the
addresses can also be set using the remote controller.
• If setting the addresses using the wireless remote controller, set the indoor unit
address and refrigerant circuit address to “00”.
(For information on setting using the wireless remote controller.)
CAUTION
Use an insulated screwdriver to set the dip switches.
• Remove the cover referring to the below Fig. A. Fix the cover after addressing setting.
En-12
9371022383-03_IM.indb 12
2017/8/11 15:11:21
Custom code setting for indoor unit
Table A
Address
Rotary switch setting
Address
Rotary switch setting
Refrigerant
circuit
REF AD SW
× 10
×1
× 10
×1
0
1
2
3
4
5
6
7
8
9
10
11
12
.
.
.
0
0
0
0
0
0
0
0
0
0
1
1
1
.
.
.
0
1
2
3
4
5
6
7
8
9
0
1
2
.
.
.
0
1
2
3
4
5
6
7
8
9
10
11
12
.
.
.
0
0
0
0
0
0
0
0
0
0
1
1
1
.
.
.
0
1
2
3
4
5
6
7
8
9
0
1
2
.
.
.
99
9
9
63
6
3
Set the DIP switch SET 3 SW1, SW2, referring to the Table B.
IU AD SW
Indoor unit
ON
DIP switch “SET 3”
OFF
SW SW SW SW
1
2
3
4
Table B
Do not set the indoor unit address (IU AD SW) at 64 to 99.
It may result in failure.
(3) Remote controller address
i) 3-wire type
Rotary switch (RC AD SW)...Factory setting “0”
When connecting multiple indoor units to 1 standard wired remote controller, set the
address at RC AD SW in sequence from 0.
Setting
Setting range
Remote controller
address
DIP switch SET 3 SW1
DIP switch SET 3 SW2
A (Factory setting)
OFF
OFF
Custom code
B
ON
OFF
C
OFF
ON
D
ON
ON
Type of switch
Setting
example
0
0 to 15
RC AD
Example
If 4 indoor units are connected.
Indoor unit
Indoor unit
Indoor unit
Indoor unit
RC AD SW
0
RC AD SW
1
RC AD SW
2
RC AD SW
3
Remote
controller
RC AD SW
Address
0
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
RC AD SW
Address
8
8
9
9
A
10
B
11
C
12
D
13
E
14
F
15
ii) 2-wire type
Rotary switch (RC AD SW)...Factory setting “0”
Since the remote controller address settings are automatically configured, you do not
need to configure them.
If configuring manually, it is necessary to configure both the indoor unit and the remote
controller. For details, please refer to the remote controller manual.
7.2. Custom code setting
Selecting the custom code prevents the indoor unit mix-up.
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote controller.
Code change
Indoor
unit
Remote
controller
Confusion
A
A
B
C
D
B
C
D
En-13
9371022383-03_IM.indb 13
2017/8/11 15:11:21
7.3. Function setting
Function
• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
• Refer to “7.1. Setting the address” for indoor unit address and refrigerant circuit address settings.
• Turn the power of the indoor unit ON before starting the setting.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air
tight test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function
number
Setting number
Default
(Forbidden)
60
00
○
(Forbidden)
61
00
○
(Forbidden)
62
00
○
Details
7.3.1. Button name and function
Function details
Function
Function
number
Filter indicator interval
Filter indicator action
Ceiling
airflow
Vertical
airflow
direction
Cool air
temperature
trigger
Heat air
temperature
trigger
Auto restart
11
Setting number
00
Standard
01
Longer
02
Shorter
00
Enable
01
Disable
02
Display only on
central remote
controller
00
Standard
13
External
control
01
High Ceiling
00
Standard
Fan setting
when cooling
thermostat
OFF
○
Adjust the filter cleaning interval
notification. If the notification
is too early, change to setting
01. If the notification is too late,
change to setting 02.
○
Enable or disable the filter indicator. Setting 02 is for use with
a central remote controller.
01
Raise
00
Standard
01
Adjust (1)
30
02
Adjust (2)
00
Standard
01
Adjust (1)
31
02
Adjust (2)
03
Adjust (3)
00
Enable
01
Disable
○
○
○
○
40
43
○
○
Follow the setting
01 on the remote
controller
00
Start/Stop
01
Emergency stop
○
46
All
01
Display only on
central remote
controller
47
49
Follow the setting
00 on the remote
controller
01 Stop
Regulate the airflow according
to the needs of the installation
location. When set to 01, the air
flow will be stronger. (Cassette
type only)
○
○
TIMER indicator
lamp (Orange)
OPERATION indicator
lamp (Green)
Adjust the vertical airflow direction. All airflow direction louvers
are adjusted together.
(Cassette type only)
Adjust the cool air trigger temperature. To lower the trigger
temperature, use setting 01. To
raise the trigger temperature,
use setting 02.
Adjust the heat air trigger temperature. To lower the trigger
temperature by 6 degrees C,
use setting 01. To lower the trigger temperature by 4 degrees
C, use setting 02. To raise the
trigger temperature, use setting
03.
Enable or disable automatic
system restart after a power
outage.
Restrain the cold airflow with
making the airflow lower when
starting heating operation. To
correspond to the ventilation,
set to 01.
Allow an external controller to
start or stop the system, or to
perform an emergency stop.
* If an emergency stop is
performed from an external
controller, all refrigerant
systems will be disabled.
* If forced stop is set, indoor
unit stops by the input to
the external input terminals,
and Start/Stop by a remote
controller is restricted.
Forced stop
00
FILTER indicator
lamp (Red)
23
02
Error report
target
Details
20
00 Super low
Cool Air
Prevention
Default
Change the target for reporting errors. Errors can either be
reported in all locations, or only
on the central remote controller.
When set to 01, the fan stops
when the thermostat is OFF in
cooling operation. Connection
of the wired remote controller
(2-wire type or 3-wire type)
and switching its thermistor are
necessary.
MANUAL AUTO
button
(Optional)
7.3.2. Checking the function settings
• Press and hold the “MANUAL AUTO” button on the indoor unit for 3 seconds to check
the function settings. It is necessary to disconnect the power in order to return to
normal operation mode.
(1) Indoor unit and refrigerant address indication
Indication pattern
Indication pattern
Indoor unit address
Refrigerant address
Indicator name
OPERATION indicator lamp
ON
Flash (1.0s ON/1.0s OFF)
(Green)
TIMER indicator lamp (Orange) Address: tens place (0.5s ON/0.5s OFF)
FILTER indicator
Address: ones place (0.5s ON/0.5s OFF)
lamp (Red)
• Indoor unit address example
(Example) ADDRESS : 24
1 cycle 12 sec
OPERATION
indicator lamp
(Green)
TIMER
indicator lamp
(Orange)
FILTER
indicator lamp
(Red)
ON
OFF
ON
OFF
ON
OFF
ON
0.5s 0.5s 0.5s 0.5s
10 sec
0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s
8 sec
• Refrigerant address example
(Example) ADDRESS : 30
1 cycle 12 sec
OPERATION
indicator lamp
(Green)
TIMER
indicator lamp
(Orange)
FILTER
indicator lamp
(Red)
ON
OFF
ON
OFF
ON
OFF
1.0s
1.0s
1.0s
1.0s
0.5s 0.5s 0.5s 0.5s 0.5s 0.5s
1.0s
1.0s
1.0s
9 sec
OFF
En-14
9371022383-03_IM.indb 14
2017/8/11 15:11:21
• Setting details
8. CASSETTE GRILLE INSTALLATION
Function number
Item
Setting number
01
Indoor unit address
00 to 63
02
Refrigeration address
00 to 99
For use with a remote controller, set all rotary switches to 0, and refer to “7.1. Setting the
address” for details.
All switches are set to 0 at the factory.
(2) Others
• Operate according to the installation Manual CASSETTE GRILLE.
• Be sure to confirm there is no gap between the cassette grille and main unit after
installing the CASSETTE GRILLE.
9. TEST RUN
9.1. Test run using Outdoor unit (PCB)
Indication pattern
Indicator Name
OPERATION indicator lamp (Green)
TIMER indicator lamp (Orange)
FILTER indicator lamp (Red)
Indication pattern
Function number; tens place
(0.5s ON/0.5s OFF)
Function number; ones place
(0.5s ON/0.5s OFF)
Setting number: (0 to 9) (0.5s ON/0.5s OFF)
(Example) Function : 31, Setting number : 2
1 cycle 12 sec
OPERATION
indicator lamp
(Green)
TIMER
indicator lamp
(Orange)
FILTER
indicator lamp
(Red)
ON
OFF
ON
OFF
ON
OFF
0.5s 0.5s 0.5s 0.5s 0.5s 0.5s
9 sec
0.5s 0.5s
11 sec
0.5s 0.5s 0.5s 0.5s
10 sec
• Refer to the Installation Manual for the outdoor unit if the PCB for the outdoor unit is to
be used for the test run.
9.2. Test run using Remote Controller
• Refer to the Installation Manual for the remote controller to perform the test run using
the remote controller.
• When the air conditioner is being test run, the OPERATION and TIMER indicators
flash slowly at the same time.
10. CHECK LIST
Pay special attention to the check items below when installing the indoor unit(s).
After installation is complete, be sure to check the following check items again.
CHECK ITEMS
If not performed correctly
Has the indoor unit been installed
correctly?
Vibration, noise, indoor unit may
drop
Has there been a check for gas leaks
(refrigerant pipes)?
No cooling, No heating
Has heat insulation work been
completed?
Water leakage
Does water drain easily from the indoor
units?
Water leakage
Is the voltage of the power source the
same as that indicated on the label on
the indoor unit?
No operation, heat or burn
damage
Are the wires and pipes all connected
completely?
No operation, heat or burn
damage
Is the indoor unit earthed (grounded)?
Short circuit
Is the connection cable the specified
thickness?
No operation, heat or burn
damage
Are the inlets and outlets free of any
obstacles?
No cooling, No heating
Does start and stop air conditioner
operation by remote control unit or
external device?
No operation
CHECK
BOX
After installation is completed, has the
proper operation and handling been
explained to the user?
En-15
9371022383-03_IM.indb 15
2017/8/11 15:11:21
Wired remote controller display
11. ERROR CODES
UTY-RNK* / UTY-RNKYT (3-wire type)
Error code
If you use a wired type remote controller, error codes will appear on the remote controller
display. If you use a wireless remote controller, the lamp on the photodetector unit will
output error codes by way of blinking patterns. See the lamp blinking patterns and error
codes in the table below.
Error indications
OPERATION
lamp (green)
TIMER
lamp
(orange)
Wired
Remote
FILTER
Controller
lamp (red) Error CODE
Error contents
(1)
(2)
Remote controller communication
error
(1)
(4)
Network communication error
UTY-RNR*Z* (2-wire type)
Error icon
Touch the [Status].
(1)
(6)
Peripheral unit communication
error
Touch the [Next Page] (or [previous page])
to switch to other indoor unit information.
Touch the [Error Information].
2-digit numbers are corresponding to
the error code in the preceding table.
For more information, refer to the installation manual of the remote controller.
UTY-RLR* (2-wire type)
(2)
(6)
Indoor unit address setting error
(2)
(9)
Connection unit number error in
wired remote controller system
(3)
(1)
Indoor unit power supply abnormal
(3)
(2)
Indoor unit main PCB error
(3)
(10)
Indoor unit communication circuit
(wired remote controller) error
(4)
(1)
Indoor unit room temp. thermistor
error
(4)
(2)
Indoor unit heat ex. temp.
thermistor error
(5)
(1)
Indoor unit fan motor 1 error
(5)
(2)
Indoor unit coil (expansion valve)
error
(5)
(3)
Indoor unit water drain abnormal
(9)
(15)
Outdoor unit miscellaneous error
(13)
(1)
RB unit error
Error icon
Error code
Display mode
For more information, refer to the installation manual of the remote controller.
: 0.5s ON / 0.5s OFF
: 0.1s ON / 0.1s OFF
( ) : Number of flashing
En-16
9371022383-03_IM.indb 16
2017/8/11 15:11:21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement