Fujitsu AUXK045GLAH Installation Manual

Fujitsu AUXK045GLAH Installation Manual
INNENGERÄT (Kassettentyp)
Nur für autorisiertes Fachpersonal.
MANUEL D’INSTALLATION
UNITÉ INTÉRIEURE (type cassette)
Pour le personnel agréé uniquement.
MANUAL DE INSTALACIÓN
UNIDAD INTERIOR (Tipo casete)
Únicamente para personal de servicio autorizado.
MANUALE DI INSTALLAZIONE
UNITÀ INTERNA (tipo a cassetta)
ΕΣΩΤΕΡΙΚΗ ΜΟΝΑΔΑ (Τύπος Κασέτας)
Μόνο για εξουσιοδοτημένο τεχνικό προσωπικό.
MANUAL DE INSTALAÇÃO
UNIDADE INTERIOR (Tipo Cassete)
Apenas para técnicos autorizados.
РУКОВОДСТВО ПО УСТАНОВКЕ
ВНУТРЕННИЙ МОДУЛЬ (кассетного типа)
Только для авторизованного обслуживающего персонала.
MONTAJ KILAVUZU
İÇ ÜNİTE (Kaset Tipi)
Português
ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ
Ελληνικά
A uso esclusivo del personale tecnico autorizzato.
Русский
AUXK018GLAH
AUXK024GLAH
AUXK030GLAH
AUXK034GLAH
AUXK036GLAH
AUXK045GLAH
AUXK054GLAH
Türkçe
AUXM018GLAH
AUXM024GLAH
AUXM030GLAH
Deutsch
INSTALLATIONSANLEITUNG
Français
For authorized service personnel only.
Español
INDOOR UNIT (Cassette Type)
Italiano
INSTALLATION MANUAL
English
TM
Yalnızca yetkili servis personeli için.
Refer to the rating label for the serial number,
manufactured year and month.
MADE IN P.R.C.
[Original instructions]
PART No. 9371022475-02
9371022475-02_IM_9L.indb 1
2/26/2018 2:40:05 PM
INSTALLATION MANUAL
PART No. 9371022475-02
VRF system indoor unit (Cassette type)
1.
SAFETY PRECAUTIONS .........................................................................................1
2.
ABOUT THIS PRODUCT..........................................................................................1
2.1. Precautions for using R410A refrigerant ............................................................1
2.2. Special tools for R410A ......................................................................................1
2.3. Accessories ........................................................................................................2
2.4. Optional parts .....................................................................................................2
4.
Do not attempt to install the air conditioner or a part of the air conditioner by yourself.
This unit must be installed by qualified personnel with a capacity certificate for handling
refrigerant fluids. Refer to regulation and laws in use on installation place.
The installation must be carried out in compliance with regulations in force in the place
of installation and the installation instructions of the manufacturer.
This unit is part of a set constituting an air conditioner. It must not be installed alone or
with non-authorized by the manufacturer.
INSTALLATION WORK ............................................................................................2
3.1. Selecting an installation location ........................................................................2
3.2. Installation dimension .........................................................................................3
3.3. Installing the unit ................................................................................................3
Always use a separate power supply line protected by a circuit breaker operating on all
wires with a distance between contact of 3mm for this unit.
PIPE INSTALLATION ...............................................................................................4
4.1. Selecting the pipe material .................................................................................4
4.2. Pipe requirement ................................................................................................4
4.3. Flare connection (pipe connection) ....................................................................4
4.4. Installing heat insulation .....................................................................................5
The units are not explosion proof and therefore should not be installed in explosive
atmosphere.
5.
INSTALLING DRAIN PIPES .....................................................................................5
6.
ELECTRICAL WIRING .............................................................................................6
6.1. Electrical requirement.........................................................................................6
6.2. Wiring method ....................................................................................................6
6.3. Unit wiring...........................................................................................................7
6.4. Connection of wiring ...........................................................................................7
6.5. Optional parts wiring...........................................................................................8
6.6. External input and external output (Optional parts) ............................................8
7.
This mark indicates procedures which, if improperly performed,
might possibly result in personal harm to the user, or damage
to property.
Read carefully all security information before use or install the air conditioner.
Contents
3.
CAUTION
FIELD SETTING .......................................................................................................10
7.1. Setting the address ............................................................................................10
7.2. Custom code setting...........................................................................................10
7.3. Function setting ..................................................................................................11
8.
CASSETTE GRILLE INSTALLATION .......................................................................11
9.
TEST RUN ................................................................................................................11
9.1. Test run using Outdoor unit (PCB) .....................................................................11
9.2. Test run using remote controller .........................................................................11
10. CHECK LIST.............................................................................................................11
11. ERROR CODES .......................................................................................................12
The unit must be correctly earthed (grounded) and the supply line must be equipped
with a differential breaker in order to protect the persons.
Never touch electrical components immediately after the power supply has been turned
off. Electric shock may occur. After turning off the power, always wait 5 minutes before
touching electrical components.
This unit contains no user-serviceable parts. Always consult authorized service personnel to repairs.
When moving, consult authorized service personnel for disconnection and installation
of the unit.
2. ABOUT THIS PRODUCT
2.1. Precautions for using R410A refrigerant
WARNING
Do not introduce any substance other than the prescribed refrigerant into the refrigeration cycle.
If air enters the refrigeration cycle, the pressure in the refrigeration cycle will become
abnormally high and cause the piping to rupture.
If there is a refrigerant leakage, make sure that it does not exceed the concentration
limit.
If a refrigerant leakage exceeds the concentration limit, it can lead to accidents such as
oxygen starvation.
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
area. Touching the refrigerant directly can cause frostbite.
If a refrigerant leakage occurs during operation, immediately vacate the premises and
thoroughly ventilate the area.
If the refrigerant comes in contact with a flame, it produces a toxic gas.
2.2. Special tools for R410A
1. SAFETY PRECAUTIONS
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information
pertaining to your safety. Be sure to observe them.
• Hand this Manual, together with the Operating Manual to the customer. Request the customer to keep them on hand for future use, such as for relocating or repairing the unit.
WARNING
This mark indicates procedures which, if improperly performed, might lead to the death or serious injury of the user.
Request your dealer or a professional installer to install the unit in accordance with this
Manual.
An improperly installed unit can cause serious accidents such as water leakage, electric
shock, or fire.
If the unit is installed in disregard of the instructions in the Installation Manual, it will void
the manufacturer’s warranty.
Do not turn ON the power until all work has been completed.
Turning ON the power before the work is completed can cause serious accidents such
as electric shock or fire.
If refrigerant leaks while work is being carried out, ventilate the area.
If the refrigerant comes in contact with a flame, it produces a toxic gas.
WARNING
To install a unit that uses R410A refrigerant, use dedicated tools and piping materials that have been manufactured specifically for R410A use. Because the pressure
of R410A refrigerant is approximately 1.6 times higher than the R22, failure to use
dedicated piping material or improper installation can cause rupture or injury.
Furthermore, it can cause serious accidents such as water leakage, electric shock, or
fire.
Tool name
Gauge manifold
Charging hose
To increase pressure resistance, the hose material and base
size were changed.
Vacuum pump
A conventional vacuum pump can be used by installing a
vacuum pump adapter.
• A conventional vacuum pump can be used by installing a
vacuum pump adapter.
• Be sure that the pump oil does not back flow into the
system. Use one capable for vacuum suction of -100.7kPa
(5 Ton, -755mmHg).
Gas leakage detector
Special gas leakage detector for HFC refrigerant R410A.
Installation work must be performed in accordance with national wiring standards by
authorized personnel only.
Except for EMERGENCY, never turn off main as well as sub breaker of the indoor units
during operation. It will cause compressor failure as well as water leakage. First, stop
the indoor unit by operating the control unit, converter or external input device and then
cut the breaker. Make sure to operate through the control unit, converter or external
input device. When the breaker is designed, locate it at a place where the users cannot
start and stop in the daily work.
Contents of change for R22 tool
Pressure is huge and cannot be measured with a conventional gauge. To prevent erroneous mixing of other refrigerants, the diameter of each port has been changed.
It is recommended to use a gauge manifold with a high
pressure display range -0.1 to 5.3 MPa and a low pressure
display range -0.1 to 3.8 MPa.
En-1
9371022475-02_IM_9L.indb 1
2/26/2018 2:40:05 PM
2.3. Accessories
Panel spacer
UTG-BKXA-W
Installation in a space of 56 mm or
greater is possible by using panel
spacer when the height behind the
ceiling is low.
Air outlet shutter plate
UTR-YDZK
Install the plate at outlet when carrying
out 3-way direction operation.
Insulation kit for high
humidity
UTZ-KXRA
Install when the condition under the roof
is over 80% in humidity and over 30°C
in temperature.
WARNING
For installation purposes, be sure to use the parts supplied by the manufacturer or other
prescribed parts.
The use of non-prescribed parts can cause serious accidents such as the unit to fall,
water leakage, electric shock, or fire.
The following installation parts are furnished. Use them as required.
Keep the Installation Manual in a safe place and do not discard any other accessories
until the installation work has been completed.
Name and Shape
Q’ty
Fresh air intake kit
UTZ-VXRA
To take fresh air.
Wireless LAN adapter
UTY-TFSXZ*
For wireless LAN control.
Application
3. INSTALLATION WORK
Operation manual
1
Installation manual
Correct initial installation location is important because it is difficult to move unit after it is
installed.
(This book)
1
3.1. Selecting an installation location
Decide the mounting position together with the customer as follows.
Operating Manual
(CD-ROM)
WARNING
1
Cable tie (Large)
For fixing the connection pipe
(Large and Small).
Select installation locations that can properly support the weight of the indoor. Install the
units securely so that they do not topple or fall.
4
CAUTION
Push mount cable tie
1
Coupler heat insulation (Small)
1
For transmission and remote
controller cable binding.
For indoor side pipe joint
(Small).
For indoor side pipe joint
(Large).
Coupler heat insulation (Large)
1
For installing indoor unit.
Template (Carton top)
1
Do not use the unit for special purposes, such as storing food, raising animals, growing
plants, or preserving precision devices or art objects.
It can degrade the quality of the preserved or stored objects.
For installing indoor unit.
Washer
8
Insulation
1
1
Hose band
Do not install where there is the danger of combustible gas leakage.
Do not install the unit near a source of heat, steam, or flammable gas.
For installing drain pipe
Drain hose
Do not install the unit in the following areas:
• Area with high salt content, such as at the seaside.
It will deteriorate metal parts, causing the parts to fail or the unit to leak water.
• Area filled with mineral oil or containing a large amount of splashed oil or steam, such
as a kitchen.
It will deteriorate plastic parts, causing the parts to fail or the unit to leak water.
• Area that generates substances that adversely affect the equipment, such as sulfuric
gas, chlorine gas, acid, or alkali.
It will cause the copper pipes and brazed joints to corrode, which can cause refrigerant
leakage.
• Area that can cause combustible gas to leak, contains suspended carbon fibers or
flammable dust, or volatile inflammables such as paint thinner or gasoline.
If gas leaks and settles around the unit, it can cause a fire.
• Area where animals may urinate on the unit or ammonia may be generated.
For installing drain pipe.
VP25 (O.D.32, I.D.25)
For installing drain hose.
1
Install the unit where drainage does not cause any trouble.
Install the indoor unit, power supply cable, transmission cable, and remote controller
cable at least 1 m away from a television or radio receivers. The purpose of this is to
prevent TV reception interference or radio noise.
(Even if they are installed more than 1 m apart, you could still receive noise under some
signal conditions.)
If children under 10 years old may approach the unit, take preventive measures so that
they cannot reach the unit.
Use the “Insulation kit for high humidity” (option), when the condition under the roof
is over 80% in humidity and over 30°C in temperature. Otherwise, there is a risk of
condensation on the ceiling.
Decide the mounting position with the customer as follows:
Drain pipe insulation
For installing drain pipe.
1
2.4. Optional parts
Description
Model
Application
UTY-XWZXZC
For output function.
(Output terminal / CNB01)
UTY-XWZXZB
For control input function.
(Apply voltage terminal / CNA01)
UTY-XWZXZD
For control input function.
(Dry contact terminal / CNA02)
UTY-XWZXZ7
For forced thermostat off function.
(Apply voltage terminal / CNA03)
UTY-XWZXZE
For forced thermostat off function.
(Dry contact terminal / CNA04)
IR receiver kit
UTY-LBHXD
For air conditioner operation.
Human sensor kit
UTY-SHZXC
To prevent waste of electricity, this
function controls the temperature setting
when no one is occupying the room.
Wide panel
UTG-AKXA-W
Wide panel hides the gap between the
ceiling hole and the Cassette grille.
External connect kit
(1) Install the indoor unit on a place having a sufficient strength so that it withstands
against the weight of the indoor unit.
(2) The inlet and outlet ports should not be obstructed; the air should be able to blow all
over the room.
(3) Leave the space required to service the air conditioner.
(4) A place from where the air can be distributed evenly throughout the room by the unit.
(5) Install the unit where connection to the outdoor unit (or RB unit) is easy.
(6) Install the unit where the connection pipe can be easily installed.
(7) Install the unit where the drain pipe can be easily installed.
(8) Install the unit where noise and vibrations are not amplified.
(9) Take servicing, etc., into consideration and leave the spaces. Also install the unit
where the filter can be removed.
En-2
9371022475-02_IM_9L.indb 2
2/26/2018 2:40:05 PM
• Refrigerant piping and drain piping positions. (unit: mm)
3.2. Installation dimension
80
10
Ceiling height is as shown in the figure.
256 mm or more (AUXM018,024,030)
298 mm or more (AUXK018,024,030,034,036,045,054)
Drain pipe
Gas pipe
Liquid pipe
Strong and durable ceiling
Drain pipe
(Connect the attached
drain hose)
1,500 mm
or more
342
293
45
180
1,800 mm to H
1,000 mm or more
140
200
3,000 mm or more
Obstruction
• Distribution ducts and fresh air inlet positions.
Floor
Fresh air
inlet position
H: Maximum height from floor to ceiling
Distribution duct
connecting port
100
83
100
83
Cut out
Standard mode
3,000
3,200
3,200
High Ceiling mode
3,500
3,600
4,200
* Be sure to make the function settings with the remote controller according to the
installed ceiling height.
Drain pipe
Refrigerant pipe
Distribution duct connecting port
Discharge direction setting
163
AUXK
036/045/054
90
AUXK
018/024/030/034
Distribution duct
connecting port
AUXM
018/024/030
Distribution duct
connecting port
H (mm)
Function setting
352
10 × Ø 3.2 hole
Detailed diagram of distribution duct connecting port (4 sides)
Ø 70
Ø 144
250
(cut out)
(bolt pitch)
4 direction
163
• The discharge direction can be selected as shown below.
3 direction
4 × Ø 3.2 hole
Fresh air inlet position
NOTE:
Conduct proper insulation when connecting the
distribution ducts and fresh air inlet.
100 mm or more *1
*1: Please ensure sufficient
service access during
installation.
* Select the most appropriate airflow direction from 3 or 4 directions according to the
shape of the room and the installation position.
* When changing the number of outlets, we recommend using the optional AIR OUTLET
SHUTTER PLATE KIT to close the outlet.
* For the specific closing pattern, please refer to the attached AIR OUTLET SHUTTER
PLATE KIT’S MANUAL. (Do so before installing the cassette grille as it will be installed
on the body.)
3.3. Installing the unit
Insulation
* When sucking in the fresh air, please detach the
insulation affixed to the drain pan.
(2) Setting the positions of hanging bolt and
ceiling opening.
• Use an installation template (packaging top
surface) to set the positions of the hanging bolt
and ceiling opening and drill holes.
Fresh air
inlet position
(3) Hanging structure.
• Select a strong structure for the hanging location.
• If necessary, reinforce the hanging bolt with quakeproof columnar support material to
prevent shaking.
• Use hanging bolts of M8 to M10.
3.3.2 Hanging preparations
WARNING
Install the air conditioner in a location which can withstand a load of at least 5 times the
weight of the main unit and which will not amplify sound or vibration. If the installation
location is not strong enough, the indoor unit may fall and cause injuries.
If the job is done with the panel frame only, there is a risk that the unit will come loose.
Please take care.
• Firmly fasten the hanging bolts as shown
in the figure or by another method.
• Install the hanging bolts at a place
where they would be capable of holding
a weight of at least 490 N per bolt.
Hole-in anchor
Hole-in plug
3.3.1 Position the ceiling hole and hanging bolts
3.3.3 Body installation
• Ceiling opening and hanging bolt pitch. (unit: mm)
WARNING
950 (Cassette grille)
130
130
140 to 145
Perform final tightening by tightening the double nut firmly.
Type
B
A
Be sure to install the body horizontally and adjust the height below the body and the
ceiling surface properly.
40
10
130
50
200
840 (Indoor unit)
130
768 (Hanging bolt pitch)
796 (Hanging bolt pitch)
860 to 910 (Ceiling opening)
950 (Cassette grille)
20 to 45
840 (Indoor unit)
50 to 100
20 to 45
20 to 45
860 to 910 (Ceiling opening)
Insert
Hanging bolt M10
(locally purchased)
(1) Positions of the ceiling opening, hanging bolt pitch, piping and ducts.
20 to 45
Concrete
Dimension (mm)
A
B
AUXM
246
256
AUXK
288
298
(1) Install the attached
washer and nut (prepared
on site) onto the hanging bolt.
(2) Hook the body onto the
hanging bolt.
(3) Adjust the dimensions of
the ceiling surface from
the body.
After installing the
cassette grille, you can
make fine adjustment of
the height of the body.
For details, refer to the
installation manual of the
cassette grille.
Hanging bolt
(locally purchased)
Washer
(Accessories)
Washer
(Accessories)
Nut A
(locally purchased)
30 mm or more
After installing
the body, tighten
the nuts.
Nut B (Double Nut)
(locally purchased)
10 to 15 mm
En-3
9371022475-02_IM_9L.indb 3
2/26/2018 2:40:06 PM
3.3.4 Leveling
4.3.1 Flaring
• Using a level, or vinyl hose
filled with water, fine adjust
so that the body is level.
• Inclined installation so
as the drain pipe side
is higher may cause a
malfunction of the float
switch, and may cause
water leakage.
Drain pipe
Vinyl hoses
4. PIPE INSTALLATION
CAUTION
Be more careful that foreign matter (oil, water, etc.) does not enter the piping than with
refrigerant R410A models. Also, when storing the piping, securely seal the openings by
pinching, taping, etc.
While welding the pipes, be sure to blow dry nitrogen gas through them.
4.1. Selecting the pipe material
CAUTION
Do not use existing pipes from another refrigeration system or refrigerant.
Use pipes that have clean external and internal sides without any contamination which
may cause trouble during use, such as sulfur, oxide, dust, cutting waste, oil, or water.
It is necessary to use seamless copper pipes.
Material : Phosphor deoxidized seamless copper pipes
It is desirable that the amount of residual oil is less than 40 mg/10 m.
Do not use copper pipes that have a collapsed, deformed, or discolored portion (especially on the interior surface). Otherwise, the expansion valve or capillary tube may
become blocked with contaminants.
Improper pipe selection will degrade performance. As an air conditioner using R410A
incurs pressure higher than when using conventional (R22) refrigerant, it is necessary to
choose adequate materials.
• Thicknesses of copper pipes used with R410A are as shown in the table.
• Never use copper pipes thinner than those indicated in the table even if they are available on the market.
Thicknesses of
Annealed Copper
Pipes (R410A)
Pipe outside diameter [mm (in)]
Thickness [mm]
6.35 (1/4)
0.80
9.52 (3/8)
0.80
12.70 (1/2)
0.80
15.88 (5/8)
1.00
19.05 (3/4)
1.20
4.2. Pipe requirement
CAUTION
Refer to the installation manual for the outdoor unit for description of allowable pipe
length and height difference.
Use pipe with water-resistant heat insulation.
CAUTION
Install heat insulation around both the gas and liquid pipes. Failure to do so may cause
water leaks.
Use heat insulation with heat resistance above 120 °C. (Reverse cycle model only)
In addition, if the humidity level at the installation location of the refrigerant piping is
expected to exceed 70 %, install heat insulation around the refrigerant piping. If the
expected humidity level is 70 to 80 %, use heat insulation that is 15 mm or thicker and
if the expected humidity exceeds 80 %, use heat insulation that is 20 mm or thicker. If
heat insulation is used that is not as thick as specified, condensation may form on the
surface of the insulation. In addition, use heat insulation with heat conductivity of 0.045
W/(m·K) or less (at 20 °C).
4.3. Flare connection (pipe connection)
WARNING
Tighten the flare nuts with a torque wrench using the specified tightening method. Otherwise, the flare nuts could break after a prolonged period, causing refrigerant to leak and
generate hazardous gas if the refrigerant comes into contact with a flame.
Use special flare tool exclusive for R410A.
(1) Cut the connection pipe to
the necessary length with a
pipe cutter.
(2) Hold the pipe downward so
that cuttings will not enter the
Die
pipe and remove any burrs.
(3) Insert the flare nut (always
use the flare nut attached to
the indoor and outdoor units
(or RB unit) respectively)
onto the pipe and perform
the flare processing with a
flare tool. Use the special
R410A flare tool. Leakage of
refrigerant may result if other
flare nuts are used.
(4) Protect the pipes by pinching
them or with tape to prevent
dust, dirt, or water from
entering the pipes.
When using conventional (R22)
flare tools to flare R410A pipes, the
dimension A should be approximately 0.5 mm more than indicated
in the table (for flaring with R410A
flare tools) to achieve the specified flaring. Use a thickness gauge
to measure the dimension A. It is
recommended that a R410A flaring
tool is used.
Check if [L] is
flared uniformly
and is not cracked
or scratched.
Pipe
Dimension A
[mm]
(Flare tool for
R410A, clutch
type)
Pipe outside
diameter
[mm (in)]
Dimension
0
[mm]
B -0.4
6.35 (1/4)
9.1
9.52 (3/8)
13.2
12.70 (1/2)
0 to 0.5
16.6
15.88 (5/8)
19.7
19.05 (3/4)
24.0
Pipe outside
diameter
[mm (in)]
Width across
flats of Flare nut
[mm]
6.35 (1/4)
17
9.52 (3/8)
22
12.70 (1/2)
26
15.88 (5/8)
29
19.05 (3/4)
36
Width across
flats
4.3.2 Bending pipes
• If pipes are shaped by hand, be careful not to collapse them.
• Do not bend the pipes in an angle more than 90°.
• When pipes are repeatedly bend or stretched, the material will harden, making it difficult
to bend or stretch them anymore.
• Do not bend or stretch the pipes more than 3 times.
CAUTION
To prevent breaking of the pipe, avoid sharp bends.
If the pipe is bent repeatedly at the same place, it will break.
4.3.3 Pipe connection
CAUTION
Be sure to install the pipe against the port on the indoor unit and the outdoor unit correctly. If the centering is improper, the flare nut cannot tightened smoothly. If the flare
nut is forced to turn, the threads will be damaged.
Do not remove the flare nut from the indoor unit pipe until immediately before connecting the connection pipe.
Do not use mineral oil on flared part. Prevent mineral oil from getting into the system as
this would reduce the lifetime of the units.
Hold the torque wrench at its grip, keeping it at a right angle with the pipe, in order to
tighten the flare nut correctly.
(1) Detach the caps and
plugs from the pipes.
(2) Center the pipe against
the port on the indoor
unit, and then turn the
flare nut by hand.
Connection pipe (Gas)
Connection pipe
(Liquid)
(3) When the flare nut is tightened properly
by your hand, hold the body side coupling
with a separate spanner, then tighten with
a torque wrench. (See the table below for
the flare nut tightening torques.)
Flare nut
[mm (in)]
Tightening torque
[N·m (kgf·cm)]
6.35 (1/4) dia.
16 to 18 (160 to 180)
9.52 (3/8) dia.
32 to 42 (320 to 420)
12.70 (1/2) dia.
49 to 61 (490 to 610)
15.88 (5/8) dia.
63 to 75 (630 to 750)
19.05 (3/4) dia.
90 to 110 (900 to 1,100)
Tighten with 2
wrenches.
Holding
wrench
Flare nut
Torque
wrench
Indoor unit pipe
(Body side)
Connection pipe
En-4
9371022475-02_IM_9L.indb 4
2/26/2018 2:40:06 PM
Working procedure
4.4. Installing heat insulation
CAUTION
After checking for gas leaks (refer to the Installation Manual of the outdoor unit), perform
this section.
Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to do
so may cause water leaks.
After checking for gas leaks,
insulate by wrapping insulation around the 2 parts (gas
and liquid) of the indoor unit
coupling, using the Coupler
heat insulation.
After installing the Coupler
heat insulation, wrap both ends
with vinyl tape so that there is
no gap.
Cable tie (Large)
(Accessories)
Coupler heat
insulation
(Accessories)
No gap
Body
Be sure to overlap
the insulation
(1) Install the attached drain hose to the drain port of the body. Install the hose band
from the top of the hose within the graphic display area. Secure firmly with the hose
band.
(2) Use vinyl adhesive agent to glue the drain piping (PVC pipe VP25) which is prepared
on site or elbow socket. (Apply color adhesive agent evenly until the gauge line and
seal)
(3) Check the drainage. (See separate diagram)
(4) Install the heat insulation.
(5) Use the attached heat insulation to insulate the drain port and band parts of the body.
Install the knob
faces upward
Attached hose band
(Accessories)
Locally arranged
vinyl pipe
Attached drain hose
heat insulation
(Accessories)
Attached drain hose
(Accessories)
Coupler heat
insulation
Attached heat insulation
(Accessories)
CAUTION
Must fit tightly against body without any gap.
5. INSTALLING DRAIN PIPES
WARNING
Do not insert the drain piping into the sewer where sulfurous gas occurs. (Heat exchange erosion may occur)
Insulate the parts properly so that water will not drip from the connection parts.
Check for proper drainage after the construction by using the visible portion of transparent drain port and the drain piping final outlet on the body.
(a) Top view
(b) Side view
VP25
CAUTION
Applying area
of adhesive
35 mm
Hose Band
Do not apply adhesive agent on the drain port of the body. (Use the attached drain hose
and connect the drain piping)
• Install the drain pipe with downward gradient (1/100 to 1/50) and so there are no rises or
traps in the pipe. Unsmooth draining caused by accumulated water flow in the pipe may
cause clogged drain.
• Use general hard polyvinyl chloride pipe (VP25) [outside diameter 32 mm].
• When the pipe is long, install supporters.
• Do not perform air bleeding. Drainage may
be blown out.
• If it is impossible to have sufficient gradient of
pipe, perform drain lift-up.
Hanging fittings
Pipe size
Drain pipe
Gauge line
4 mm or less
20 mm
(c) Top view
VP25 (O.D. 32 mm)
(d) Hose opening view
Wind the attached heat insulation
around the hose band
1.5 to 2 m
Make sure the
alignment is on top
VP25 (O.D. 32 mm)
Downward gradient 1/100 to 1/50
Make sure there are no gaps
NOTE: Check for drainage
PROHIBITED:
Rise
5 to 10 mm
Trap
Air bleeding
When lifting up drain:
• Height of inclined pipe should be less than 850 mm from the ceiling. A rise dimension
over this range will cause leakage.
• Lift up the pipe vertically at the position of 300 mm or less from the unit.
Downward gradient
300 mm or less
1/100 to 1/50
VP25 (O.D. 32 mm)
local arrangement
Pour about 1 liter of water from
the position shown in the diagram or from the airflow outlet
to the dew tray. Check for any
abnormalities such as strange
noises and whether the drain
pump functions normally.
850 mm or less
Horizontal or
upward gradient
850 mm or less
VP30 (O.D. 38 mm) or more
Downward gradient 1/100 to 1/50
En-5
9371022475-02_IM_9L.indb 5
2/26/2018 2:40:06 PM
6. ELECTRICAL WIRING
A. Current breaker requirements
Model
MCA
AUXM018GLAH
0.24 A
Electrical work must be performed in accordance with this Manual by a person certified
under the national or regional regulations. Be sure to use a dedicated circuit for the unit.
An insufficient power supply circuit or improperly performed electrical work can cause
serious accidents such as electric shock or fire.
AUXM024GLAH
0.29 A
AUXM030GLAH
0.50 A
AUXK018GLAH
0.41 A
Before starting work, check that power is not being supplied to the all units.
AUXK024GLAH
0.41 A
For wiring, use the prescribed type of cables, connect them securely, making sure that
there are no external forces of the cables applied to the terminal connections.
Improperly connected or secured cables can cause serious accidents such as overheating the terminals, electric shock, or fire.
AUXK030GLAH
0.46 A
AUXK034GLAH
0.46 A
AUXK036GLAH
0.57 A
Securely install the electrical box cover on the unit.
An improperly installed electrical box cover can cause serious accidents such as electric
shock or fire through exposure to dust or water.
AUXK045GLAH
0.81 A
AUXK054GLAH
1.04 A
WARNING
Install sleeves into any holes made in the walls for wiring. Otherwise, a short circuit
could result.
Use the included connection cables and power cables or ones specified by the manufacturer. Improper connections, insufficient insulation, or exceeding the allowable current
can cause electric shock or fire.
Do not modify the power cables, use extension cables, or use any branches in the wiring. Improper connections, insufficient insulation, or exceeding the allowable current can
cause electric shock or fire.
Match the terminal block numbers and connection cable colors with those of the outdoor
unit (or RB unit). Erroneous wiring may cause burning of the electric parts.
Securely connect the connection cables to the terminal board. In addition, secure the
cables with wiring holders. Improper connections, either in the wiring or at the ends of
the wiring, can cause a malfunction, electric shock, or fire.
• MCA: Minimum Circuit Ampacity
• MFA: Maximum Fuse Ampacity
MFA
When the power crossover wiring is done,
make it so that the total of the MCA of the
connected RB units and indoor units does not
exceed the 15 A. For RB unit MCA, refer to
the RB unit installation manual.
If the capacity of connected RB units and
indoor units exceeds the upper limit, either
add breakers or use a breaker with a greater
capacity.
20 A
B. Earth leakage breaker requirements
*1: Heat pump type: indoor units,
Heat recovery type: indoor units
and RB units.
*2: If the 100 mA capacity breaker is
not provided, split the quantity of
the indoor units into small groups
of 9 units or less and provide a
breaker with capacity of 30 mA for
each group.
Maximum connectable “indoor units”
or “indoor units +
RB units” (*1)
Breaker capacity
30 mA, 0.1 sec or less
44 or less
100 mA, 0.1 sec or less
45 to 148 (*2)
6.1.1 Cable specifications
Recommended
cable size (mm²)
Cable type
Remark
Always fasten the outside covering of the connection cable with the cable clamp. (If the
insulator is chafed, electric discharge may occur.)
Power supply cable
2.5
Type245 IEC57
or equivalent
Install an earth leakage breaker. In addition, install the earth leakage breaker so that the
entire AC main power supply is cut off at the same time. Otherwise, electric shock or fire
could result.
Transmission cable
0.33
22 AWG LEVEL 4 (NEMA)
LONWORKS®
non-polar 2 core, twisted pair
compatible cable
solid core diameter 0.65 mm
Always connect the earth (ground) cable.
Improper earthing (grounding) work can cause electric shocks.
Remote controller
cable (2-wire type)
0.33 to 1.25
Install the remote controller cables so as not to be direct touched with your hand.
Perform wiring work in accordance with standards so that the air conditioner can be
operated safely and positively.
Connect the connection cable firmly to the terminal board. Imperfect installation may
cause a fire.
If the supply cable is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
Sheathed PVC
cable *1
2 Cable + earth (ground)
Non-polar 2 core, twisted
pair
*1: Use shielded cable in accordance with local rules for remote controller cables.
6.2. Wiring method
Outdoor unit or RB unit *1
Transmission
CAUTION
Earth (Ground) the unit.
Do not connect the earth (ground) cable to a gas pipe, water pipe, lightning rod, or a
telephone earth (ground) cable.
Improper earthing (grounding) may cause electric shock.
Do not connect power supply cables to the transmission or remote controller terminals,
as this will damage the product.
Never bundle the power supply cable and transmission cable, remote control cable
together. Separate these cable by 50 mm or more. Bundling these cables together will
cause miss operation or breakdown.
When handling PCB, static electricity charged in the body may cause malfunction of the
PCB. Follow the cautions below:
• Establish an earth (ground) for the indoor and outdoor units and peripheral devices.
• Cut power (breaker) off.
• Touch metal part of the indoor units for more than 10 seconds to discharge static
electricity charged in the body.
• Do not touch terminals of parts and patterns implemented on PCB.
6.1. Electrical requirement
• Select the power cable type and size
Voltage rating
230 V
in accordance with relevant local and
national regulations.
Operating
198 to 264 V (50 Hz)
• Specifications for local wiring power cord
198 to 253 V (60 Hz)
range
and branch wiring are in compliance with
local code
• Max. wire length: Set a length so that the voltage drop is less than 2%. Increase the wire
diameter when the wire length is long.
Breaker should be installed at every refrigerant system. Do not use a breaker in a different
refrigerant system.
Refer to the table for the breaker specifications of each installation condition. Perform
the power crossover wiring within the range of the same refrigerant system. When the
crossover wiring is done, make a connection for indoor units to satisfy conditions A and B
below.
Indoor unit
Transmission
Power supply
*2
Breaker
Power supply
Indoor unit
Remote
control
Indoor unit
*2
*2
Breaker
Breaker
*3
Remote controller
(Master)
*3
Remote controller
(Slave)
*3
Remote controller
*1: When connecting to the Heat Recovery System, refer to the installation manual of the
RB unit.
*2: Earth (Ground) the remote controller if it has an earth (ground) cable.
*3: The 3-wire type remote controller is not used.
(Crossover wiring of power supply)
Indoor unit
Power supply
Indoor unit
Power supply
Indoor unit
Power supply
Pull box
Breaker
Pull box
Power supply
En-6
9371022475-02_IM_9L.indb 6
2/26/2018 2:40:06 PM
6.3.2 Transmission and Remote controller cable
6.3. Unit wiring
Transmission cable
• Before attaching the cable to terminal block.
Remote controller cable
30 mm
6.3.1 Power supply cable
Shield
cable
(no film)
20 mm
Earth (Ground)
cable
30 mm
30 mm
45 mm
• Connect remote controller and transmission cables as shown in Fig. C.
Fig. C
A. For solid core wiring
(1) To connect the electrical terminal, follow the below diagram and connect after looping
it around the end of the cable.
(2) Use the specified cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(3) Use an appropriate screwdriver to tighten the terminal screws.
Do not use a screwdriver that is too small, otherwise, the screw heads may be damaged and prevent the screws from being properly tightened.
(4) Do not tighten the terminal screws too much, otherwise, the screws may break.
(5) See the table for the terminal screw tightening torques.
(6) Please do not fix 2 power supply cables with 1 screw.
PROHIBITED
GOOD
Different diameter
Strip 25 mm
Connect to 1 side
WARNING
Loop
Tighten the terminal screws to the specified torques, otherwise, abnormal overheating
may be produced and possibly cause heavy damage inside the unit.
Tightening torque
Screw with
special washer
Screw with
special washer
Cable
Cable end (Loop)
Cable end (Loop)
Terminal block
Cable
Do not apply branch wiring. It may result electric shock or fire.
WARNING
M3 screw (Transmission / X1, X2)
(Remote controller / Y1, Y2, Y3)
0.5 to 0.6 N·m
(5 to 6 kgf·cm)
CAUTION
To peel the film from the lead cable, use a dedicated tool that will not damage the
conductor cable.
When installing a screw on the terminal block, do not cut the cable by overtightening the
screw. On the other hand, an undertightened screw can cause faulty contact, which will
lead to a communication failure.
6.4. Connection of wiring
When using solid core cables, do not use the ring terminal. If you use the solid core
cables with the ring terminal, the ring terminal's pressure bonding may malfunction and
cause the cables to abnormally heat up.
(1) Remove the control box cover and wiring cover by loosening the screws.
B. For strand wiring
(1) Use ring terminals with insulating sleeves as shown in the figure below to connect to
the terminal block.
(2) Securely clamp the ring terminals to the cables using an appropriate tool so that the
cables do not come loose.
(3) Use the specified cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(4) Use an appropriate screwdriver to tighten the terminal screws. Do not use a screwdriver that is too small, otherwise, the screw heads may be damaged and prevent the
screws from being properly tightened.
(5) Do not tighten the terminal screws too much, otherwise, the screws may break.
(6) See the table for the terminal screw tightening torques.
(7) Please do not fix 2 power supply cables with 1 screw.
Ring terminal
Strip 10 mm
Sleeve
Screw with
special washer
Screw with
special washer
Cable
Ring terminal
Wiring connecting port
(for power supply cable)
Wiring
connecting port (for
transmission cable
and remote controller
cable)
Wiring cover
Control box cover
(2) Thread each cable through the holes or indents of the cabinet and connect the wires.
(3) After wiring is complete, secure the cables with the cable clamps.
L
N
Ring terminal
Earth
(ground)
Terminal block
Cable
clamp
Cable
WARNING
Use ring terminals and tighten the terminal screws to the specified torques, otherwise,
abnormal overheating may be produced and possibly cause heavy damage inside the
unit.
Terminal number
Tightening torque
M3.5 screw (Power supply/L, N, GND)
1.2 to 1.8 N·m (12 to 18 kgf·cm)
Power supply cable
En-7
9371022475-02_IM_9L.indb 7
2/26/2018 2:40:06 PM
X1, X2: Transmission cable
6.5.2 Connection methods
Wire modification for External
input/output wire
IMPORTANT:
Be sure to insulate the connection between the
(1) Remove insulation from wire atwires.
tached to wire kit connector.
Locally
Wire kit connector
(2) Remove insulation from field
purchased
(optional parts)
supplied cable. Use crimp type
insulated butt connector to join field
cable and wire kit wire.
(3) Connect the wire with connecting
Solder and insulate the connected parts.
wire with solder.
Cut
Push mount cable tie (accessories)
Connection terminals and wiring arrangement
Y1, Y2: Remote controller cable
(do not use Y3.)
In following figure, all the possible connectors are connected for description.
In actual installation, you cannot connect all the connectors at once.
Cable hooks
1
CNA01 CNA03
CNA02
2
3
CNB01
CN65
CNA04
Cable clamp
(4) Replace the Control box
cover and Wiring cover.
Securely tighten the
screws.
6.6. External input and external output (Optional parts)
6.6.1 External input
• Indoor unit can be Operation/Stop, Emergency stop or Forced stop by using indoor unit
PCB CNA01 or CNA02.
• “Operation/Stop” mode, “Emergency stop” mode or “Forced stop” mode can be selected
with function setting of indoor unit.
• Indoor unit can be Forced thermostat off by using indoor unit PCB CNA03 or CNA04.
• A twisted pair cable (22 AWG) should be used. Maximum length of cable is 150 m.
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• The wire connection should be separate from the power cable line.
Cure the wiring connecting
port and remote controller
connecting port with putty or
heat insulation so that insects
or dust will not enter the unit.
CAUTION
Input select
Do not bundle the remote controller cable, or wire the remote controller cable in parallel,
with the indoor unit connection wire (to the outdoor unit) and the power supply cable. It
may cause erroneous operation.
Use either one of these types of terminal according to the application. (Both types of
terminals cannot be used simultaneously.)
6.5. Optional parts wiring
When a power supply must be provided at the input device you want to connect, use the
Apply voltage terminal ([CNA01], [CNA03]).
● Apply voltage terminal ([CNA01], [CNA03])
6.5.1 Connector and DIP switch position
CNA03
CNB01
CN65
DC power supply
12 to 24V
Controller PCB
Input
device 1
CNA01
Input
device 2
ON
DIP switch
(SET 2)
OFF
SW1 SW3
SW2 SW4
Name
CNA01
CNA03
CNA02
CNA04
DIP switch SET 2 (SW2)
CNB01
CN65
Apply voltage terminal
Application
For external input
Dry contact terminal
Input signal type switching
Output terminal
For external output
For one of the following.
• MODBUS® convertor (*1)
• Wireless LAN adapter (*1)
*1: For details, refer to each installation manual.
Input
device 3
CNA04
P.C.B
Load
resistance
CNA01
*a
*b
SET 2
CNA02
*1
Load
resistance
*a
Load
resistance
CNA03
*a
Connected unit
*1: Make the power supply DC 12 to 24 V. Select a power supply capacity with an ample
surplus for the connected load.
Do not impress a voltage exceeding 24 V across pins 1-2, and 1-3.
*a: The allowable current is DC 5 mA to 10 mA. (Recommended: DC 5 mA)
Provide a load resistance such that the current becomes DC 10 mA or less.
Select very low current use contacts (usable at DC 12 V, DC 1 mA or less).
*b: The polarity is [+] for pin 1 and [-] for pin 2 and 3. Connect correctly.
En-8
9371022475-02_IM_9L.indb 8
2/26/2018 2:40:06 PM
When connected to Apply voltage terminals of multiple indoor units with a connected unit,
be sure to make a branch outside the indoor unit using a pull box, etc. as shown on below
example.
CNA01
Input signal
Indoor unit
CNA01
OFF → ON
Operation
Ch2
OFF → ON
Stop
* The last command has priority.
* The indoor units within the same remote controller group operates in the same mode.
● When function setting is “Emergency stop” mode.
Connector
Input signal
Ch1 of CNA01 or CNA02
Command
OFF → ON
Emergency stop
ON → OFF
Normal
CNA01
Indoor unit
[In the case of “Pulse” input]
P.C.B
Connected unit
Command
Ch1
[In the case of “Edge” input]
P.C.B
Load
resistance
Indoor unit
P.C.B
Load
resistance
Input
device 1
Connector
CNA01 or CNA02
DC power supply
12 to 24V
Input
device 2
[In the case of “Pulse” input]
Connector
Input signal
CNA01 or CNA02
Command
Ch1
OFF → ON
Emergency stop
Ch2
OFF → ON
Normal
* All indoor units of same refrigerant system stops when Emergency stop operates.
● Dry contact terminal ([CNA02], [CNA04])
When a power supply is unnecessary at the input device you want to connect, use the Dry
contact terminal ([CNA02], [CNA04]).
● When function setting is “Forced stop” mode.
[In the case of “Edge” input]
Connector
P.C.B
Input signal
Ch1 of CNA01 or CNA02
*c
Ch 1
CNA02
*c
Ch 2
*d
*c
Ch 3
Connector
CNA04
Connected unit
*c: Select very low current use contacts (usable at DC 12 V, DC 1 mA or less).
*d: The wiring is different from Apply voltage terminals. Be sufficiently careful when wiring.
When connected to Dry contact terminals of multiple indoor units with a connected unit,
insulate each indoor unit with relay, etc. as shown on below example.
K5
CNA02
Indoor unit
P.C.B
P.C.B
Input device 1
Normal
Input signal
CNA01 or CNA02
K6
CNA02
Input device 2
K1 - K6: Relay
(Device for DC Current)
NOTE :
When connected to multiple indoor units directly, it will cause breakdown.
OFF → ON
Forced stop
Ch2
OFF → ON
Normal
* When the forced stop is triggered, indoor unit stops and Operation/Stop operation by a
remote controller is restricted.
* When forced stop function is used with forming a remote controller group, connect the
same equipment to each indoor unit within the group.
• Selection method of functions
“Operation/Stop” mode or “Emergency stop” mode, “Forced stop” mode can be selected
with function setting of indoor unit.
[“Edge” input only]
Connector
Input signal
Ch3 of CNA03 or CNA04
Thermostat off
ON → OFF
Normal
• A twisted pair cable (22AWG) should be used. Maximum length of cable is 25m.
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• Output voltage: Hi DC12V±2V, Lo 0V.
• Permissible current: 50mA
● When indicator etc. are connected directly
P.C.B
Operation
indicator
Error
indicator
CNB
01
Indoor unit Fan
status indicator
connected unit
● Input signal type
● When connecting with unit equipped with a power supply
Edge
The input signal type can be selected.
It is switched by DIP switch on the indoor unit PCB.
Input signal type
OFF (Factory setting)
Edge
ON
Pulse
P.C.B
Pulse
The width of pulse must be
longer than 200 msec.
● When function setting is “Operation/Stop” mode.
Ch1 of CNA01 or CNA02
Connected
device 1
Connected
device 2
CNB
01
Connected
device 3
[In the case of “Edge” input]
Connector
Command
OFF → ON
6.6.2 External output
Operation behavior
DIP switch [Set 2 SW2]
Command
Ch1
Output select
Indoor unit
Power supply for relay
CNA02
Indoor unit
K4
K3
ON → OFF
● Forced thermostat off function
P.C.B
K2
Forced stop
[In the case of “Pulse” input]
GND
K1
Command
OFF → ON
Input signal
Command
OFF → ON
Operation
ON → OFF
Stop
connected unit
Relay (Locally purchased)
En-9
9371022475-02_IM_9L.indb 9
2/26/2018 2:40:06 PM
Table A
Operation behavior
Connector
Output voltage
0V
External output 1
Pins 1-2
CNB01
DC 12 V
0V
External output 2
Pins 1-3
DC 12 V
0V
External output 3
Pins 1-4
DC 12 V
Address
Status
Refrigerant
circuit
Stop
Operation
Normal
Error
Indoor unit fan stop
Indoor unit fan operation
7. FIELD SETTING
There are 3 methods for address setting by FIELD SETTING as follows.
Please set by either of the methods.
Each setting method is described in below (1) to (3).
(1) IU AD, REF AD SW settings: This section (7.1 Setting the address)
(2) Remote controller settings:
Refer to the wired or wireless remote controller manual
for detailed setting information. (Set IU AD, REF AD
SW to 0)
(3) Automatic address settings: Refer to the outdoor unit manual for detailed setting
information. (Set IU AD, REF AD SW to 0)
0
1
2
3
4
5
6
7
8
9
10
11
12
⁞
99
Rotary switch setting
REF AD SW
× 10
×1
0
0
0
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
9
1
0
1
1
1
2
⁞
⁞
9
9
Address
Rotary switch setting
IU AD SW
× 10
×1
0
0
0
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
9
1
0
1
1
1
2
⁞
⁞
6
3
Indoor unit
0
1
2
3
4
5
6
7
8
9
10
11
12
⁞
63
Do not set the indoor unit address (IU AD SW) at 64 to 99.
It may result in failure.
7.2. Custom code setting
• Selecting the custom code prevents the indoor unit mix-up. (figure below)
(Up to 4 codes can be set.)
• Perform the setting for both the indoor unit and the remote controller.
7.1. Setting the address
CAUTION
Code change
Confusion
Use an insulated screwdriver to set the dip switches.
A
Indoor unit
B
C
D
B
C
D
• Open the cover referring to the figure below. Close and fix the cover after addressing
setting.
For refrigerant
circuit address
For indoor
unit address
(1) Loosen the screw.
IU AD
×10
REF AD
×1
×10
RC AD
×1
Remote
controller
A
• Custom code setting for indoor unit
Set the DIP switch SET3 SW1, 2, referring to the
figure and table below.
IU AD
×10
REF AD
×1
SET3
SET3
×10
RC AD
×1
SET4
SET4
DIP switch “SET3”
DIP switch “SET3”
(2) Slide the cover and open it.
ON
7.1.1 Indoor unit address
• Rotary switch (IU AD × 1)...Factory setting “0”
• Rotary switch (IU AD × 10)...Factory setting “0”
When connecting multiple indoor units to 1 refrigerant system, set the address at IU AD
SW as shown in the Table A.
OFF
SW SW SW SW
1 2 3 4
DIP switch
SET3
Custom code
A (Factory
setting)
B
C
D
SW1
OFF
ON
OFF
ON
SW2
OFF
OFF
ON
ON
7.1.2 Refrigerant circuit address
• Rotary switch (IU AD × 1)...Factory setting “0”
• Rotary switch (IU AD × 10)...Factory setting “0”
In the case of multiple refrigerant systems, set REF AD SW as shown in the Table A for
each refrigerant system.
Set to the same refrigerant circuit address as the outdoor unit.
Setting
Setting range
Indoor unit address
0 to 63
Refrigerant circuit
address
0 to 99
Type of switch
Setting
example 2
IU AD × 10
IU AD × 1
REF AD × 10
REF AD × 1
Setting example 63
• If working in an environment where the wireless remote controller can be used, the addresses can also be set using the remote controller.
• If setting the addresses using the wireless remote controller, set the indoor unit address
and refrigerant circuit address to “00”.
(For information on setting using the wireless remote controller.)
En-10
9371022475-02_IM_9L.indb 10
2/26/2018 2:40:06 PM
00
Single
setpoint auto
mode
(traditional)
01
Dual setpoint
auto mode
7.3. Function setting
• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
• Refer to “7.1 Setting the address” for indoor unit address and refrigerant circuit address
settings.
• Turn the power of the indoor unit ON before starting the setting.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air tight
test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Function
Filter indicator interval
Filter indicator action
Function
number
11
20
Vertical
airflow
direction
23
Cool air
temperature
trigger
30
Heat air
temperature
trigger
Auto restart
Cool Air
Prevention
External
control
31
40
43
00
Standard
01
Longer
02
Shorter
00
Enable
01
Disable
02
Display only
on central
remote
controller
00
Standard
01
High Ceiling
00
Standard
01
Adjust
00
Standard
01
Adjust (1)
02
Adjust (2)
00
Standard
01
Adjust (1)
02
Adjust (2)
03
Adjust (3)
00
Enable
01
Disable
00
Super low
01
Follow the
setting on
the remote
controller
00
Start/Stop
01
Emergency
stop
46
02
Error report
target
47
68
00 0°C
01 0.5°C
02 1.0°C
03 1.5°C
Deadband
value
69
Choose the minimum temperature
between cooling and heating
settings (deadband) for Dual
setpoint auto mode (set in No. 68).
04 2.0°C
05 2.5°C
06 3.0°C
Setting number
13
Ceiling
airflow
Auto mode
type
Switch the setting method of
auto mode to single or dual
(cooling/heating).
For heat pump systems, it is
necessary to set the master
indoor unit (by wired remote
controller).
Forced stop
00
All
01
Display only
on central
remote
controller
00
Follow the
setting on
the remote
controller
01
Stop
Fan setting when
cooling
thermostat
OFF
49
(Forbidden)
60
00
(Forbidden)
61
00
(Forbidden)
62
00
Default
Details
07 3.5°C
Adjust the filter cleaning interval
notification. If the notification
is too early, change to setting
01. If the notification is too late,
change to setting 02.
08 4.0°C
Enable or disable the filter indicator. Setting 02 is for use with a
central remote controller.
Regulate the airflow according
to the needs of the installation
location. When set to 01, the air
flow will be stronger. (Cassette
type only)
Adjust the vertical airflow direction. All airflow direction louvers
are adjusted together.
Adjust the cool air trigger
temperature. To lower the trigger
temperature, use setting 01. To
raise the trigger temperature,
use setting 02.
Adjust the heat air trigger
temperature. To lower the trigger
temperature by 6 degrees C, use
setting 01. To lower the trigger
temperature by 4 degrees C, use
setting 02. To raise the trigger
temperature, use setting 03.
Enable or disable automatic
system restart after a power
outage.
Restrain the cold airflow with
making the airflow lower when
starting heating operation. To
correspond to the ventilation,
set to 01.
Allow an external controller to
start or stop the system, or to
perform an emergency stop.
* If an emergency stop is
performed from an external
controller, all refrigerant
systems will be disabled.
* If forced stop is set, indoor
unit stops by the input to the
external input terminals, and
Start/Stop by a remote controller is restricted.
Change the target for reporting
errors. Errors can either be reported in all locations, or only on
the central remote controller.
09 4.5°C
8. CASSETTE GRILLE INSTALLATION
• Operate according to the installation Manual CASSETTE GRILLE.
• Be sure to confirm there is no gap between the cassette grille and main unit after installing the CASSETTE GRILLE.
9. TEST RUN
9.1. Test run using Outdoor unit (PCB)
Refer to the Installation Manual for the outdoor unit if the PCB for the outdoor unit is to be
used for the test run.
9.2. Test run using remote controller
• Refer to the Installation Manual for the remote controller to perform the test run using the
remote controller.
• When the air conditioner is being test run, the OPERATION and TIMER indicator lamp
flash slowly at the same time.
10. CHECK LIST
Pay special attention to the check items below when installing the indoor unit(s). After
installation is complete, be sure to check the following check items again.
Check items
Check
box
If not performed correctly
Has the indoor unit been installed
correctly?
Vibration, noise, indoor unit may
drop
Has there been a check for gas leaks
(refrigerant pipes)?
No cooling, No heating
Has heat insulation work been completed?
Water leakage
Does water drain easily from the indoor
units?
Water leakage
Is the voltage of the power source the
same as that indicated on the label on
the indoor unit?
No operation, heat or burn damage
Are the wires and pipes all connected
completely?
No operation, heat or burn damage
Is the indoor unit earthed (grounded)?
Short circuit
Is the connection cable the specified
thickness?
No operation, heat or burn damage
Are the inlets and outlets free of any
obstacles?
No cooling, No heating
Does start and stop air conditioner
operation by remote control unit or
external device?
No operation
After installation is completed, has the
proper operation and handling been
explained to the user?
When set to 01, the fan stops
when the thermostat is OFF in
cooling operation. Connection
of the wired remote controller (2-wire type or 3-wire type)
and switching its thermistor are
necessary.
En-11
9371022475-02_IM_9L.indb 11
2/26/2018 2:40:06 PM
Wired Remote Controller Display
11. ERROR CODES
If you use a wired type remote controller, error codes will appear on the remote controller
display. If you use a wireless remote controller, the lamp on the photodetector unit will
output error codes by way of blinking patterns. See the lamp blinking patterns and error
codes in the table below.
OPERATION
lamp (green)
Error indications
TIMER lamp FILTER lamp
(orange)
(red)
(1)
(2)
Wired Remote
Controller Error
code
Error icon
Touch the [Next Page] (or [previous page])
to switch to other indoor unit information.
Error contents
Remote controller communication error
(1)
(4)
Network communication error
(1)
(6)
Peripheral unit communication error
(2)
(6)
Indoor unit address setting error
(2)
(9)
Connection unit number
error in wired remote
controller system
(3)
(1)
Indoor unit power supply
abnormal
(5)
(1)
Indoor unit main PCB
error
(3)
(10)
Indoor unit communication circuit (wired remote
controller) error
(4)
(1)
Indoor unit room temp.
thermistor error
(4)
(2)
Indoor unit heat ex.
temp. thermistor error
(4)
(4)
Human sensor error
(5)
(1)
Indoor unit fan motor
1 error
(5)
(2)
Indoor unit coil (expansion valve) error
(5)
(3)
Indoor unit water drain
abnormal
(9)
(15)
Outdoor unit miscellaneous error
(10)
(8)
Poor refrigerant circulation
(13)
(1)
RB unit error
Display mode
UTY-RNR*Z* (2-wire type)
Touch the [Status].
Touch the [Error Information].
2-digit numbers are corresponding to
the error code in the preceding table.
For more information, refer to the installation manual of the remote controller.
UTY-RLR* (2-wire type)
Error icon
Error code
For more information, refer to the installation manual of the remote controller.
: 0.5 s ON / 0.5 s OFF
: 0.1 s ON / 0.1 s OFF
( ) : Number of flashing
En-12
9371022475-02_IM_9L.indb 12
2/26/2018 2:40:06 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement