Fujitsu AXGA18ARTA Operation Manual

Fujitsu AXGA18ARTA Operation Manual
Unit Overview
Controller
ROOM AIR CONDITIONER
OPERATION MANUAL
ENGLISH
Position
THERMOSTAT
1–10
(OFF)
P/N 9352970030-03
Refer to the rating label with the serial number.
MADE IN THAILAND
Before using this product, read these instructions thoroughly and keep this manual for future reference.
Safety Precautions
(SUPER
QUIET)
CAUTION
This mark warns of death or serious injury.
l Do not bundle the power supply cable.
l In the event of a malfunction (burning smell, etc.), immediately stop
operation, turn off the electrical breaker or disconnect the power
supply plug, and consult authorized service personnel.
l Always turn off the electrical breaker or disconnect the power supply
plug whenever cleaning the air conditioner or the air filter.
l This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that they do
not play with the appliance.
l If you see lightning or hear thunder, there might be a lightning
strike. To prevent electric shock hazard, stop the operation of the air
conditioner, and do not touch the unit during thunderstorm.
CAUTION
Provide occasional ventilation during use.
Do not direct airflow at fireplaces or heating apparatus.
Do not climb on, or place objects on the air conditioner.
Do not hang objects from the unit.
Do not set flower vases or water containers on top of air conditioners.
Do not expose the indoor side of air conditioner directly to water.
Do not operate the air conditioner with wet hands.
Do not pull power supply cord.
Check the condition of the support brackets for damage.
Do not place animals or plants in the direct path of the airflow.
Do not drink the water drained from the air conditioner.
l Do not touch the aluminum fins of heat exchanger built-in the indoor or
outdoor unit to avoid personal injury when you install or maintain the unit.
l Do not use in applications involving the storage of foods, plants or
animals, precision equipment, or art works.
l Do not apply any heavy pressure to the aluminum fins of heat
exchanger.
l Operate only with air filter installed.
l Do not block or cover the intake grille and outlet port.
l Ensure that any electronic equipment is at least 1 m away from the unit.
l When installing the unit, take precautions to prevent access by infants.
l Do not use inflammable gases near the air conditioner.
Unit Overview
SUPPER
QUIET
6
0
SELECT
LEVER
EXHAUST AIR
Fan (High speed) and compressor
operate at rapid cooling.
This lever is used to adjust the air flow
direction and sweep angle.
OPEN
Room air is drawn outside.
CLOSE
Exhaust vent is closed.
To obtain maximum cooling effect in the hot summer select position HIGH POWER on the master control. Maximum moisture removal, air circulation and
dust removal are effected at the same time.
Selection of SUPER QUIET reduces operating noise.
Air Circulation
An adequate flow of air is very important for comfort. When the master control knob is set at “FAN” position, the fan only is actuated so that the air is filtered
and circulated without cooling effect.
Air circulation only without cooling effect may also be achieved with the thermostat knob turned counterclockwise to “1” position and with the master control
at either “HIGH POWER” or “SUPER QUIET” position.
Thermostat Control
The thermostat is set by means of the thermostat control. When the room temperature is higher than the thermostat setting, the compressor is
automatically switched on to provide a cooling effect. When the room temperature is lower than the thermostat setting, the compressor is automatically
switched off to stop cooling.
It can be seen therefore, that the thermostat serves to keep the room temperature constant by causing the compressor to start and stop automatically.
1. When you wish to lower the temperature, turn the thermostat control clockwise in the direction of the higher numbers on the dial.
2. When you wish to increase the temperature, turn the thermostat control counterclockwise in the direction of the lower numbers.
3. When the thermostat is set at positions “5”, “6”, or “7”, comfortable room temperatures can usually be obtained. Note that it is unhealthy for the room
temperature to be lower than approximately 22 °C.
4. When the thermostat control is positioned at “10”, the room-side fin coil may freeze up due to excessively low room temperature (for example, below
18°C) caused by low outdoor temperature at night.
Once the fin coil becomes frozen, the airflow from the air conditioner is restricted by the frost, and the room temperature may rise due to the resultant
weak cooling performance of the air conditioner.
5. The thermostat positions “8”, “9”, and “10” can be used when the room temperature does not become sufficiently low. This condition may occur when the
thermostat switches off automatically because cooled air, when it passes through the vertical airflow louvers positioned downwards and the horizontal
airflow louvers positioned to the left, makes a short circuit and the recirculated air touches the sensor of the thermostat.
Note: The thermostat controls the compressor only and accordingly the fan is constantly circulating air even during the period when the compressor is off.
Important: When restarting the cooling operation after it has been turned off by either master control of thermostat, be sure to allow at least 3 minutes.
If cooling operation is restarted immediately after it is turned off, an over current will flow through the compressor motor and the safety
device will be actuated. If the safety device is actuated it will not be possible to restart the compressor motor for about 20 minutes.
F
2
9
OFF
Air Flow Adjustment
OFF
NEUTRAL
SUPER WAVE ZONE
Right side
With this air conditioner, three air directions can be obtained as shown in the figures on the left side.
When the air flow direction is set, adjust to the desired sweep angle.
Left side
Center
Adjusting Air Flow Direction and Sweep Angle
SELECT LEVER
CLOSE
OPEN
10
1
ON
HIGH
POWER
8
SUPER WAVE
NO
R
When the SUPER WAVE switch is turned to “ON” position, the horizontal airflow louvers is automatically actuated and sweeps the jet of air alternately, left
and right and thus more effective cooling will be obtained.
The louvers may be stopped at any position when SUPER WAVE switch is turned off. Sweep angle and direction can be adjusted with the select lever.
The sweep can span an area either to the right or to the left. Select a sweep angle suitable to the layout of the room and the position of the air conditioner
in the room which the air conditioner is installed.
AL
3
Power supply cable
AN
M
7
4
COOL
EXHAUST AIR
Screw
Right
Left
Air filter
Front panel
Intake grille
Care and Maintenance
1.
2.
3.
4.
5.
Move the select lever fully left to the “NEUTRAL”.
Position the vertical louver to either the left end, center, or the right end .
Move the select lever fully to the right end of the SUPER WAVE ZONE.
Set the SUPER WAVE switch to “ON”.
The sweep angle can be adjusted within the SUPER WAVE ZONE range. When the select lever is
returned to the left, the sweep angle decreases. Adjust sweep angle according to preference.
Note: If the select lever is returned to the “NEUTRAL” in error, the vertical louvres do not function properly.
In this event, carry out the procedure from the beginning.”
Center
Select lever
Installation (Instructions for Installers)
CAUTION
Installation dimension
Cleaning the Air Filter
Accessory
The following installation accessory is
supplied. Use it as required.
Sunshade
75 or less
300 or more
Unit 455
Installation hole
455–460
l During maintenance, be sure to place the removed components in a safe place to avoid damage to them.
l Do not touch the aluminum fins of heat exchanger built-in the indoor or outdoor unit to avoid personal injury when you install or maintain the unit.
Also, pay attention not to be scratched or pinched your hand by inner parts.
l Never use water hotter than 40 °C. The unit body may warp or change color.
l Do not use inflammable sprays such as lacquer or hair spray near the air conditioner.
The unit can be damaged by gasoline, benzine, thinners, insecticides and other chemical agents.
l Before cleaning the unit, be sure to turn it off and all the power supply has been disconnected.
Name and Shape
600
or more
Wall
200 or more
If dirt is allowed to collect in the air filter, the airflow will be reduced, leading to reduced performance, and increased operating noise. Be sure to clean the
filters at the beginning of the operating season, and about every 2 weeks during periods of frequent operation.
The air filter is attached to the front panel, and you need to remove the intake grille first, when you get access to the air filter.
Intake grille removal
Drain tube
(Outer diameter: Φ16)
Unit 710
Condenser air inlet louvers
With lifting up small tabs on the air
filter, pull the filter toward you.
Front panel
Air filter cleaning
Use a vacuum cleaner to remove dust and dirt from the air filter, or wash in a synthetic detergent. After washing, dry in a shaded place, then reinstall.
Cleaning the unit
5-10 mm
Clean the unit by wiping with a cloth moisten with cool or warm water, then wipe with another soft, clean, and dry cloth.
When not using the unit for extended periods (1 month or more)
Operate the unit on fan mode for about one-half day on a day with clear weather, to assure that the internal parts are dry.
When not using the unit for extended periods, turn off the electrical breaker or disconnect the power plug for safety.
200
or more
200
or more
Unit 670
Installation hole 670–673
Fit flashing or insert caulking compound
behind top outside architrave.
Recommended architrave
57 mm (2 1/4”)×13 mm (1/2”)
tapering to 8 mm (5/16”)
typical all round on front and
rear of unit.
Timber frame–typical all
round on front and rear of
unit.
50 mm (2”)×6 mm (1/4”)
sponge rubber strip–typical
all round on front and rear
of unit.
Condenser air inlet louvers
must be completely clear of
outside architrave surface.
Recommended height:
750-1500 mm from the
floor
Attach field supplied cabinet support brackets
to the cabinet and the wall, it is required.
Check the power cord
l Remove the built-up dirt and dust on the power plug and the electrical outlet periodically.
l Check the power cord occasionally to confirm that it is not damaged by cuts or abrasions. If you discover damage to the cord, consult authorized service
personnel.
Inspections and repairs:
Depending on the conditions of use, the internal parts of an air conditioner will become dirty after about two or three season of use, and performance
may be affected. For this reason, regular professional maintenance is recommended. Consult authorized service personnel.
Q’ty
Insulation
1
Wall
Unit: mm
Typical installation
Air filter removal
Push the bottom of the intake grille up
with your hand, and pull it toward you.
● When constructing a timber frame, arrange so that the outside rear of the air
conditioner is between 5 and 10 mm lower than the front of the unit.
This allows condensed water to drain off outside the room.
If the inside of the air conditioner is lower, condensed water and rain may flow
into the room.
Avoid installing the air conditioner near a fireplace or other heating
apparatus.
In the place where bears be sufficient to the weight of the air
conditioner concerning installation, noise and vibration choose
such place without increasing.
● For installation, avoid any places in direct sunlight. Combined
installation with a sunshade is recommended; installing the unit
under direct sunlight may cause low cooling performance or
increasing of the electricity consumption.
● Consult the installation in a special place to a selling agent.
Because sea breeze sometimes becomes to a cause of
malfunction by corrosion etc., in the case that the place become
use with machine oil, the place of many place etc., that occur,
sulfuration gas such as a hot spring area that hits in a seashore
area it buys and give consultation to that selling agent.
● Avoid the neighbourhood that be discharged dust, a lampblack,
steam, such as an exhaust port, a ventilation fan.
● It is place where do not give neighbours trouble about removal
water or a wind and noise.
● Where practicable, locate the air conditioner with the lower edge
of the cabinet approximately 0.75 m (29.5”) to 1.5 m (59”) from
the floor. This usually gives the optimum air circulation pattern
within the room for cooling and heating.
● When installing the attached insulation (620 mm x 40 mm, t12),
insert it from the inside of the room so that the insulation fills up
the gap between the rails on the inner bottom of the cabinet and
bottom side of the base.
Power Supply
Troubleshooting
WARNING
Before requesting service, perform the following checks:
Symptom
Problem
Noise is heard:
● During operation and immediately after stopping the unit, the sound of water flowing in the air
conditioner’s piping may be heard. Also, noise may be particularly noticeable for about 2 to 3
minutes after starting operation (sound of coolant flowing).
● During operation, a slight squeaking sound may be heard. This is the result of minute expansion and
contraction of the front cover due to temperature changes.
Smells:
● Some smell may be emitted from the unit. This smell is the result of room smells (furniture, tobacco,
etc.) which have been taken into the air conditioner.
Mist or steam are emitted:
● During cooling operation, a thin mist may be seen emitted from the unit. This results from the sudden
cooling of room air by the air emitted from the air conditioner, resulting in condensation and misting.
Does not operate at all:
● Is the power plug disconnected from its outlet?
● Has there been a power failure?
● Has a fuse blown out, or a circuit breaker been tripped?
Poor cooling performance:
●
●
●
●
●
●
Is the air filter dirty?
Are the air conditioner’s intake grille or outlet port blocked?
Did you adjust the room temperature settings (thermostat) correctly?
Is there a window or door open?
In the case of cooling operation, is a window allowing bright sunlight to enter? (Close the curtains.)
In the case of cooling operation, are there heating apparatus or computers inside the room, or are
there too many people in the room?
l Wiring connections must be performed by a qualified person in accordance with the specifications. The voltage rating for this product is 220-240V at
50Hz. It should be operated with the range of 198 to 264V.
l This air conditioner must be connected to a power source that has an electrical impedance of 0.100 Ω or less or has a supply current of 100 A or
greater. If the power supply does not meet the specifications, contact the power company.
l In order to enable efficient and trouble-free operation of your air conditioner, connect supply main of your air conditioner through an exclusive circuit,
having a time delay fuse, to the correct power supply described on the rating plate.
l The circuit breaker with all pole disconnection must be incorporated in permanent wiring.
l Always use a separate power supply line protected by a circuit breaker operating on all wires with a distance between contact of 3 mm for this unit.
l To protect the persons, ground the unit correctly, and use the power supply cord combined with an Earth Leakage Circuit Breaker (ELCB).
l This appliance shall be installed in accordance with national wiring regulations.
l Always connect the earth (ground) wire. Improper earthing (grounding) work can cause electric shocks.
l When using the power plug to power the unit from the power outlet, use a power plug that conforms to the maximum current value described on the
rating label of the unit.
Connect BROWN line of the power supply cable to the “Live” terminal of the power outlet, and the earth (ground)
line (GREEN and YELLOW) to the earth (ground) terminal.
Remaining line should be connected to the neutral terminal of the power outlet.
Front panel removal and installation
Test run (Instructions for Installers)
Perform test operation and check items 1 and 2 below.
1. Indoor side
Is operation of each switch and lever normal?
Do the airflow direction louver operate normally?
Is the drain normal?
Screws
2. Outdoor side
Is there any abnormal noise and vibration during operation?
Will noise, wind, or drain water from the unit disturb the neighbors?
BLUE
N
L
BROWN
GREEN/YELLOW
Front panel removal
If the problem persists after performing these checks, immediately stop operation, turn off the electrical breaker or disconnect the power plug, and consult
authorized service personnel.
9352970030-03_EN.indd 1
Horizontal airflow louvers stop enabling
airflow to be directed in any desired
direction.
Air Direction Control
5
CHECK ONCE
MORE
OFF
By setting EXHAUST AIR control lever to the appropriate positions between “OPEN” and “CLOSE” positions, it is possible to expel the room air to the
desired extent. The quantity of air to be expelled will increase when the lever is positioned closer to the “OPEN” position.
Control panel
NORMAL
FUNCTIONS
ON
Exhaust Air Control
Vertical airflow louvers
Horizontal airflow louvers
Air inlet
(HIGH
POWER)
Description
Horizontal airflow louvers continuously
change the direction of airflow. When
the master control knob is set to “OFF”,
the SUPER WAVE does not operate.
Cooling
WARNING
l
l
l
l
l
l
l
l
l
l
l
SUPER WAVE
Position
Operation
This mark warns of injury or damage to property.
l Do not attempt to install this air conditioner by yourself.
l This unit contains no user-serviceable parts. Always consult authorized
service personnel for repairs.
l If the power supply cord is damaged, it must be replaced by the
manufacturer, its service agent, or similarly qualified persons in order to
avoid a hazard.
l When moving, consult authorized service personnel for disconnection
and installation of the unit.
l Do not become over-exposed to cold air by staying in the direct path of
the air flow of the air conditioner for extended periods of time.
l Do not insert fingers or objects into the outlet port or intake grille.
l Do not start and stop air conditioner operation by turning off the
electrical breaker or disconnecting the power supply plug and so on.
l Take care not to damage the power supply cord.
l Do not modify the power cables, use extension cables, or use any
branches in the wiring. Improper connections, insufficient insulation, or
exceeding the allowable current can cause electric shock or fire.
The air conditioner is switched off.
Fan (Medium speed) and compressor
(NORMAL)
operate at intermediate cooling.
To prevent personal injury, injury to others, or property damage, read this section carefully before you use this product, and be sure to comply following
safety precautions.
Incorrect operation due to failure to follow the instructions may cause harm or damage, the seriousness of which is classified as follows:
WARNING
Controller
Fan only operates at MED speed,
without cooling room air is circulated
and cleaned.
Fan (Low speed) and compressor
operate at quiet cooling.
(FAN)
MASTER
CONTROL
Description
As the knob is turned clockwise the
higher numbers on the dial indicate
lower temperature.
Remove the front panel in the following manner.
The front panel is attached to the cabinet with snap clips at the top and screws at the bottom. Remove the
removable panel first and you will see two screws at the left and right of the bottom side. Take them off.
Hold up the front panel with your hands to remove it completely.
Front panel installation
When refitting the front panel, insert the two clips on the upper part of the panel into the two slots at the
top side of the cabinet.
Press the front panel at its bottom side and fix it with screws. This completes refitting of the front panel.
6/20/2560 BE 15:50
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement