Fujitsu AXGT18FHTC-B Operation Manual

Fujitsu AXGT18FHTC-B Operation Manual
Unit Overview
Drain tube
Air outlet
AX SERIES
WIRELESS TYPE
(At the bottom of the backside)
Moisture condensed from the air during cooling is
drained here.
Warm air is blown out.
Horizontal airflow direction
louvers
ROOM AIR CONDITIONER
OPERATION MANUAL
ENGLISH
PART No. 9386269148
Intake grille
Front panel
Refer to the rating label with the serial number.
MADE IN THAILAND
Before using this product, read these instructions thoroughly and keep this manual for future reference.
Safety Precautions
To prevent personal injury, injury to others, or property damage, read this section carefully before you use this product, and be sure to comply following
safety precautions.
Incorrect operation due to failure to follow the instructions may cause harm or damage, the seriousness of which is classified as follows:
WARNING
CAUTION
This mark warns of death or serious injury.
This mark warns of injury or damage to property.
WARNING
z Do not attempt to install this air conditioner by yourself.
z This unit contains no user-serviceable parts. Always consult authorized
service personnel for repairs.
z When moving, consult authorized service personnel for disconnection
and installation of the unit.
z Do not become over-exposed to cold air by staying in the direct path of
the air flow of the air conditioner for extended periods of time.
z Do not insert fingers or objects into the outlet port or intake grille.
z Do not start and stop air conditioner operation by turning off the
electrical breaker or disconnecting the power supply plug and so on.
z Take care not to damage the power supply cord.
z Do not modify the power cables, use extension cables, or use any
branches in the wiring. Improper connections, insufficient insulation, or
exceeding the allowable current can cause electric shock or fire.
z Do not bundle the power supply cable.
z In the event of a malfunction (burning smell, etc.), immediately stop
operation, turn off the electrical breaker or disconnect the power
supply plug, and consult authorized service personnel.
z Always turn off the electrical breaker or disconnect the power supply
plug whenever cleaning the air conditioner or the air filter.
z This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that they do
not play with the appliance.
z If you see lightning or hear thunder, there might be a lightning strike.
To prevent electric shock hazard, turn off the air conditioner by using
the remote controller, and do not touch the unit or the power plug
during thunderstorm.
Provide occasional ventilation during use.
Do not direct airflow at fireplaces or heating apparatus.
Do not climb on, or place objects on the air conditioner.
Do not hang objects from the unit.
Do not set flower vases or water containers on top of air conditioners.
Do not expose the air conditioner directly to water.
Do not operate the air conditioner with wet hands.
Do not pull power supply cord.
Turn off power source when not using the unit for extended periods.
Check the condition of the installation stand for damage.
Do not place animals or plants in the direct path of the airflow.
Do not drink the water drained from the air conditioner.
Do not touch the aluminum fins of heat exchanger built-in the indoor or
outdoor unit to avoid personal injury when you install or maintain the
unit.
Vertical airflow direction louvers
Control airflow in the vertical (up-down) direction.
Air inlet
(Both sides)
Air filter
Power supply plug
Removes all dirt and
dust from the air.
SUPER WAVE indicator (Green)
Lights during SUPER WAVE working.
Screw
Securing the front panel
to the unit.
MANUAL AUTO button
Remote control
signal receiver
Signals from the remote control unit
are received here.
OPERATION indicator
(Green)
TIMER indicator (Orange)
 Lights when unit is operating.
 Flashes quickly for about 1 second
when a signal is received from the
remote control unit.
Lights during ON TIMER, OFF TIMER, and SLEEP
TIMER.
If the TIMER indicator flashes when the timer is
operating, it indicates that a fault has occurred with
the timer setting.
Remote controller display
Set temperature / Timer Indicator
* The accompanying illustration depicts the
display with all indicators lighted; in actual use,
however, only those indicators currently required
are displayed.
 Shows the thermostat setting.
 During the timer mode is set, the function is
displayed. (After the timer mode is shown, the
thermostat setting is returned to temperature
indication.)
Operation Mode Indicator
z Do not use in applications involving the storage of foods, plants or
animals, precision equipment, or art works.
z Do not apply any heavy pressure to radiator fins.
z Operate only with air filter installed.
z Do not block or cover the intake grille and outlet port.
z Ensure that any electronic equipment is at least 1 m away from the
unit.
z Avoid installing the air conditioner near a fireplace or other heating
apparatus.
z When installing the unit, take precautions to prevent access by infants.
z Do not use inflammable gases near the air conditioner.
z Always turn off the electrical breaker or disconnect the power supply
plug whenever cleaning the air conditioner or the air filter.
 Pressed 10 seconds or less (AUTOMATIC
mode)
• Fan speed will be set to “AUTO” and the
thermostat will be set for 24 °C.
• To stop operation, either press the MANUAL
AUTO button once again.
 Pressed 10 seconds or more (Forced cooling)
• The forced cooling operation is used at the
time of installation.
Only for authorized service personnel’s use.
• When the forced cooling operation starts by
any chance, press START/STOP button to
stop the operation.
Remote Controller Overview
CAUTION
z
z
z
z
z
z
z
z
z
z
z
z
z
Control airflow in the horizontal (right-left) direction.
Air is taken in here.
Shows the operation mode
(AUTO, COOL, DRY, and FAN)
Fan Speed Indicator
Timer Mode Indicator
Transmit Indicator
Shows the current fan speed.
Shows the timer mode
O : “OFF TIMER” symbol
I : “ON TIMER” symbol
: “SLEEP TIMER” symbol
Displayed when a signal is sent to the air
conditioner.
Signal Transmitter
Controls signal sent to the air conditioner from here.
MODE button
FAN button
Press to select operating mode
(AUTO, COOL, DRY, FAN)
SET TEMP. buttons (
/
Press to select fan speed. (AUTO, HIGH, MED, and
LOW).
)
SUPER WAVE button
Press to set the unit’s thermostat.
Use to set the desired airflow direction.
Power Supply
START/STOP button
TEST RUN button
WARNING
z In order to enable efficient and trouble-free operation of your air conditioner, connect the power plug of your air conditioner through an exclusive
circuit, having a time delay fuse, to the correct power supply described on the rating plate.
z The circuit breaker with all pole disconnection must be incorporated in permanent wiring.
z If the power supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a
hazard.
z This appliance shall be installed in accordance with national wiring regulations.
Connect BROWN line of the power supply cable to the “Live” terminal of the power outlet, and the earth (ground) line (GREEN and YELLOW) to
the earth (ground) terminal.
Remaining line should be connected to the neutral terminal of the power outlet.
Preparation
Press to start and stop operation.
This button is used when testing the air
conditioner after installation.
Do not use under normal condition.
RESET button
This button is used when replacing batteries.
SLEEP button
Use to set time for OFF the air conditioner.
CANCEL button
Press to cancel the setting time.
OFF TIMER button
ON TIMER button
Use to set time for OFF the air conditioner.
Use to set time for ON the air conditioner.
Airflow Direction Adjustment
Vertical airflow direction louvers:
Rotate the vertical airflow louvers upward, or downward.
Loading batteries (AAA/R03/LR03×2) on the remote controller
WARNING
1
Take precautions to prevent infants from accidentally swallowing
batteries.
CAUTION
 When not using the remote controller for an extended period,
remove the batteries to avoid possible leakage and damage to the
unit.
 If leaking battery fluid comes in contact with your skin, eyes, or
mouth, immediately wash with copious amounts of water, and
consult your physician.
 Dead batteries should be removed quickly and disposed of properly,
either by placing in a public battery collection receptacle, or by
returning to a properly equipped dealer.
Press and slide the battery
compartment lid on the reverse
side to open it.
Right-Left Airflow-direction Louvers:
Control airflow in the horizontal (right-left) direction.
When the SUPER WAVE button
blow air to the left and right.
Vertical airflow direction louvers
To stop SUPER WAVE operation, press the button again.
Slide in the direction of the arrow
mark.
while pressing the
2
Indicators
Insert batteries.
Be sure to align the battery polarities (
3
) correctly.
Close the battery compartment lid.
SUPER WAVE indicator will light.
Notes:
 Never mix new and used batteries, or batteries of different types.
 Batteries should last about 1 year under normal use. If the remote
controller’s operating range becomes appreciably reduced, replace the
batteries and press the reset button with the tip of a ballpoint pen or
other small object.
Turn on the power
SUPER WAVE indicator go out.
Connect the power plug to an electrical point.
Connect securely,
without looseness.
In the case of direct line
connections, turn on the breaker.
To use the remote controller
 The remote control unit must be pointed at signal receiver to operate
correctly.
 When a signal is properly received by the air conditioner, a beeping
sound will be heard.
 If no beep is heard, press the remote control unit button again.
Operating range:
Within about 7 meters
Signal receiver
is pressed, the louvers move and
Notes:
 Signals will not be transmitted properly if a wall, curtain, or other object
is between the air conditioner and the remote control unit.
 The air conditioner may fail to operate properly if strong direct light
is allowed to strike the signal receiver. Use a curtain to shade strong
sunlight from windows, and place strong lamps at a distance away from
the signal receiver.
 Do not place the remote control unit in locations where it may be
subjected to heat from direct sunlight or from heating apparatus.
 Do not subject the remote control unit to strong impacts, and do not
allow water or other liquids to splash on it.
 When the remote control unit is used in rooms furnished with instantlighting type fluorescent lamps, the air conditioner may fail to receive
control signals correctly. Consult with authorized service personnel
when purchasing a new fluorescent lamp.
 If another electric appliance is operated by the remote control unit move
the appliance away or consult with authorized service personnel.
Automatic Operation
 When Automatic operation first selected, the fan will operate at low
speed for 1 minute, during which time the unit detects the room
conditions and selects the proper operating mode.
If the difference between thermostat setting and actual room
temperature is more than +2ºC→Cooling operation
If the difference between thermostat setting and actual room
temperature is less than +2ºC→Dry operation
1
Press the START/STOP button.
2
Press the MODE button to select AUTO.
The air conditioner will start operation.
The operating mode “AUTO” will appear alone in the display. The
transmit indicator will flash to indicate the command has been sent,
and about 3 seconds later the entire display panel will reappear.
 If the mode automatically selected by the unit is not what you wish,
select one of the mode operation (COOL, DRY, and FAN.)
2
1
Basic Operations
Mode Operation (COOL, DRY, and FAN)
Cooling: Use to cool your room.
Drying: Use for gently cooling while dehumidifying your room.
 You cannot heat the room during drying mode.
 During drying mode, the unit will operate at low speed, in order
to adjust room humidity, the unit’s fan may stop from time to time.
Also, the fan may operate at very low speed when detecting room
humidity.
 The fan speed cannot be changed manually when drying mode has
been selected.
Fan: Use to circulate air through your room without changing its
temperature.
 You cannot use the unit to heat and cool your room.
Each time the MODE button
is pressed, the mode will change in the
following order.
AUTO
COOL
FAN
DRY
About 3 seconds later, the entire display will reappear.
Thermostat Setting
button: Press to raise the thermostat setting.
button: Press to lower the thermostat setting.
 Thermostat setting range:
AUTO .................................. 18-30 °C
Cooling/Dry ......................... 18-30 °C
9386269148-EN.indd 1
The thermostat cannot be used to set room temperature during the FAN
mode (the temperature will not appear on the remote controller’s display.)
About 3 seconds later, the entire display will reappear.
The thermostat setting should be considered a standard value, and
may differ somewhat from the actual room temperature.
Notes:
• In the following situation, the setting temperature will be 24ºC even if
you set the setting temperature lower than 24ºC.
—When changing the operation mode
—When stopping the operation once, then restart the operation
* When you change the setting temperature higher than 24 ºC, the
changed setting temperature will be saved.
Fan Speed Setting
Each time the button is pressed, the fan speed changes in the following
order:
AUTO
HIGH
MED
LOW
About 3 seconds later, the entire display will reappear.
Temperature and Humidity Range
Permissible ranges of temperature and humidity are as follows:
Outdoor temperature: About 21 °C to 55 °C
Cooling
Operation
Indoor temperature: About 18 °C to 35 °C
Indoor humidity: About 80 % or less. If the unit is used for long periods under conditions of high humidity, water may humidity, water
may condense on and drip from the surface of the unit.
Outdoor temperature: About 18 °C to 55 °C
Drying
Operation
Indoor temperature: About 18 °C to 35 °C
Indoor humidity: If the unit is used for long periods under conditions of high humidity, water may condense on and drip from the surface
of the unit.
If the unit is used under higher temperature conditions than those noted here, the automatic protection circuit may operate, interrupting the operation.
If the unit is used under lower temperature conditions than those noted here, the heat exchanger may freeze, causing water leakage or other malfunction.
 Do not use the air conditioner for any purpose other than room cooling, room drying or fan.
When the FAN CONTROL is set to AUTO:
COOL: Operation begins and as the room temperature approaches that of
the thermostat setting, the fan speed switches to the low setting.
2019/12/16 9:05:45
TIMER Operation
Care and Maintenance
OFF TIMER (stops the air conditioner operation at the set time)
1
Press the START/STOP button.
2
Press OFF TIMER button to select desired times.
CAUTION
z During maintenance, be sure to place the removed components in a safe place to avoid damage to them.
z Do not touch the aluminum fins of heat exchanger built-in the indoor or outdoor unit to avoid personal injury when you install or maintain the unit.
Also, pay attention not to be scratched or pinched your hand by inner parts.
z Never use water hotter than 40 °C. The unit body may warp or change color.
z Do not use inflammable sprays such as lacquer or hair spray near the air conditioner.
The unit can be damaged by gasoline, benzine, thinners, insecticides and other chemical agents.
z Before cleaning the unit, be sure to turn it off and all the power supply has been disconnected.
(if the unit is already operating, proceed to step 2).
The unit’s green OPERATION indicator will light.
Press OFF TIMER button to change from temperature setting to timer indicator.
Each time the button is pressed, the time changes in the following order:
1
2
(hour)
) on the remote controller’s display is flashing.
Set the time while the OFF TIMER indicator (
Cleaning the Air Filter
If dirt is allowed to collect in the air filter, the airflow will be reduced, leading to reduced performance, and increased operating noise. Be sure to clean the
filters at the beginning of the operating season, and about every 2 weeks during periods of frequent operation.
The air filter is attached to the front panel, and you need to remove the intake grille first, when you get access to the air filter.
ON TIMER (begins the air conditioner operation at the set time)
1
Press the START/STOP button.
2
Press ON TIMER button to set the expected time.
Air filter cleaning
Intake grille removal
Push the bottom of the intake grille up with your hand, and pull it toward you.
(If the unit is already operating, proceed to step 2.)
The unit’s green OPERATION indicator will light.
Use a vacuum cleaner to remove dust and dirt from the air filter, or wash in
a synthetic detergent. After washing, dry in a shaded place, then reinstall.
Air filter installation
To attach the filter to the front panel, with aligning the both sides of the filter
to the front panel, insert the upper edge of the filter to the rail on the front
panel. Then make sure that the lower edge of the filter is firmly inserted to
the rail too.
If ON TIMER button is pressed, it will be changed into time indication from temperature indication.
Each time the button is pressed, the time changes in the following order:
1
(hour)
2
Set the time while the ON TIMER mark (
) on the remote controller’s display is flashing.
Note: When you set the setting temperature lower than 24 ºC and activate the On timer, the setting
temperature will be changed at 24 ºC. You can change the setting temperature.
To Cancel the TIMER
To Change the TIMER Settings
Press the CANCEL button
Press the ON TIMER button
.
To Stop the Air Conditioner Operation while
the TIMER is Operating
Air filter removal
With lifting up small tabs on the air filter, pull the filter toward you.
or OFF TIMER
button as required.
The air filter can be installed either way up.
After attaching the air filter, reinstall the intake grille.
To Change Operating Conditions
If you wish to change the operating conditions (mode, fan speed,
thermostat setting), after making the timer setting, wait until the entire
display reappears, then press the appropriate buttons to change to the
desired operating condition.
Press the START/STOP button.
SLEEP TIMER Operation
Cleaning the unit
Clean the unit by wiping with a cloth moisten with cool or warm water, then wipe with another soft, clean, and dry cloth.
Front panel removal
Front panel installation
1. Remove one screw securing the front panel.
1. Hook the upper edge of the front panel (2 places) to the unit.
2. Push the small projections on the bottom side of the front panel
upward to unlatch the lower side. Then with holding up the front panel
with your hands, remove it toward you.
2. Press the lower edge of the front panel, and secure it with the screw.
Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operation is stopped.
About SLEEP TIMER
SLEEP timer setting
To prevent excessive warming or cooling during sleep, the SLEEP timer function automatically modifies
the thermostat setting in accordance with the time setting. When the time has elapsed, the air conditioner
completely stops.
Set time
1 hour
During Cooling/Dry operation:
When the SLEEP timer is set, the thermostat setting is automatically raised 1 °C every 1 hour.
When the thermostat has been raised a total of 2 °C, the thermostat setting at that time is maintained until
the set time has elapsed, at which time the air conditioner automatically turns off.
1 °C
2 °C
To Use the SLEEP TIMER
To Change the SLEEP TIMER Settings
While the air conditioner is operating or stopped,
press the SLEEP button
.
Press the SLEEP button once to display the last
setting time.
The SLEEP TIMER indicator (
will light.
Press the SLEEP button again to change the time.
) on the remote controller’s display
Each time the button is pressed, the time changes in the following order
(Change from the last setting time):
1.0
2.0
3.0
5.0
7.0
9.0 (hour)
Within 3 seconds after the indicator lights, the time can be changed by
pressing SLEEP button once again.
(RESET)
a
a
When not using the unit for extended periods (1 month or more)
Each time the button is pressed, the time changes in the following order:
1.0
2.0
3.0
5.0
7.0
9.0 (hour)
To Cancel the TIMER
Operate the unit on fan mode for about one-half day on a day with clear weather, to assure that the internal parts are dry.
When not using the unit for extended periods, disconnect the power plug for safety.
(RESET)
About 3 seconds later, the entire display will reappear.
Press the CANCEL button
Check the power cord
The unit’s OPERATION indicator (green) and the TIMER indicator (orange)
light.
.
To Stop the Air Conditioner Operation while
the TIMER is Operating
z Remove the built-up dirt and dust on the power plug and the electrical outlet periodically.
z Check the power cord occasionally to confirm that it is not damaged by cuts or abrasions. If you discover damage to the cord, consult authorized service
personnel.
Inspections and repairs:
Depending on the conditions of use, the internal parts of an air conditioner will become dirty after about two or three season of use, and performance
may be affected. For this reason, regular professional maintenance is recommended. Consult authorized service personnel.
Press the START/STOP button.
Troubleshooting
Before requesting service, perform the following checks:
Installation
Symptom
Installation dimension
NORMAL
FUNCTIONS
Sunshade
300 or more
Unit 455
Installation hole
455–460
80 or less
200
or more
600
or more
Unit 710
200
or more
Does not operate
immediately:
 If the unit is stopped and then immediately started again, the compressor will not operate for about
3 minutes, in order to prevent fuse blowouts.
 Whenever the power plug is disconnected and then reconnected to a power outlet, the protection
circuit will operate for about 3 minutes, preventing unit operation during that period.
Noise is heard:
 During operation and immediately after stopping the unit, the sound of water flowing in the air
conditioner’s piping may be heard. Also, noise may be particularly noticeable for about 2 to 3
minutes after starting operation (sound of coolant flowing).
 During operation, a slight squeaking sound may be heard. This is the result of minute expansion and
contraction of the front cover due to temperature changes.
Smells:
 Some smell may be emitted from the unit. This smell is the result of room smells (furniture, tobacco,
etc.) which have been taken into the air conditioner.
Mist or steam are emitted:
 During cooling operation, a thin mist may be seen emitted from the unit. This results from the sudden
cooling of room air by the air emitted from the air conditioner, resulting in condensation and misting.
Poor cooling performance:
 The setting temperature may change to the initial setting (24ºC) automatically. In this case, set the
temperature again.
Does not operate at all:





Is the power plug disconnected from its outlet?
Has there been a power failure?
Has a fuse blown out, or a circuit breaker been tripped?
Are the remote controller batteries loaded properly?
Is the timer operating?
Poor cooling performance:






Is the air filter dirty?
Are the air conditioner’s intake grille or outlet port blocked?
Did you adjust the room temperature settings (thermostat) correctly?
Is there a window or door open?
In the case of cooling operation, is a window allowing bright sunlight to enter? (Close the curtains.)
In the case of cooling operation, are there heating apparatus or computers inside the room, or are
there too many people in the room?
Poor dry performance:
 Set the thermostat to a temperature setting that is lower than the present room temperature. Dry
modes will not operate if the thermostat is set higher than the actual room temperature.
The unit operates differently
from the remote controller
setting:
 Are the remote controller batteries dead?
 Are the remote controller batteries loaded properly?
Wall
Wall
Unit 670
Drain tube
(Outer diameter: Φ16)
Installation hole 670–673
Unit: mm
Typical installation
Condenser air inlet louvers
Front panel
Fit flashing or insert caulking compound
behind top outside architrave.
Recommended architrave
57 mm (2 1/4")×13 mm (1/2")
tapering to 8 mm (5/16")
typical all round on front and
rear of unit.
5-10 mm
Timber frame–typical all
round on front and rear of
unit.
50 mm (2")×6 mm (1/4")
sponge rubber strip–typical
all round on front and rear
of unit.
Condenser air inlet louvers
must be completely clear of
outside architrave surface.
Recommended height:
750-1500 mm from the
floor
Attach local purchased cabinet support brackets
to the cabinet and the wall, it is required.
 When constructing a timber frame, arrange so that the outside rear of the air
conditioner is between 5 and 10 mm lower than the front of the unit.
This allows condensed water to drain off outside the room.
If the inside of the air conditioner is lower, condensed water and rain may flow
into the room.
In the event of a malfunction (burning smell, etc.), immediately
stop operation, disconnect the power plug, and consult
authorized service personnel.
In the place where bears be sufficient to the weight of the air
conditioner concerning installation, noise and vibration choose
such place without increasing.
 For installation, avoid any places in direct sunlight. Combined
installation with a sunshade is recommended; installing the unit
under direct sunlight may cause low cooling performance or
increasing of the electricity consumption.
 Consult the installation in a special place to a selling agent.
Because sea breeze sometimes becomes to a cause of
malfunction by corrosion etc., in the case that the place become
use with machine oil, the place of many place etc., that occur,
sulfuration gas such as a hot spring area that hits in a seashore
area it buys and give consultation to that selling agent.
 Avoid the neighborhood that be discharged dust, a lampblack,
steam, such as an exhaust port, a ventilation fan.
 It is place where do not give neighbors trouble about removal
water or a wind and noise.
 Where practicable, locate the air conditioner with the lower edge
of the cabinet approximately 0.75 m (29.5") to 1.5 m (59") from
the floor. This usually gives the optimum air circulation pattern
within the room for cooling and heating.
 When installing the attached insulation (620 mm x 40 mm, t12),
insert it from the inside of the room so that the insulation fills up
the gap between the rails on the inner bottom of the cabinet and
bottom side of the base.
Error Codes
If you use a wireless remote controller, the lamp on the photodetector unit will output error codes by way of blinking patterns. See the Indicator blinking
patterns and error codes in the table below. An error display is displayed only during operation.
Error display
OPERATION Indicator
(green)
TIMER Indicator
(orange)
Description
SUPER WAVE Indicator
(green)
(3)
(5)
Manual auto switch error
(4)
(1)
Room temperature sensor error
(4)
(2)
Heat exchanger temperature sensor error
CHECK ONCE
MORE
If the problem persists after performing these checks, or if you notice burning smells, or the TIMER indicator flashed, immediately stop operation,
disconnect the power plug, and consult authorized service personnel.
AUTO Restart
In Event of Power Interruption
 The air conditioner power has been interrupted by a power failure. The air conditioner will then restart automatically in its previous mode when the
power is restored.
 Operated by setting before the power failure.
 If a power failure occurs during TIMER operation, the timer will be reset and the unit will begin (or stop) operation at the new time setting. In the event
that this kind of timer fault occurs the TIMER indicator will flash.
Specifications
MODEL
POWER
REFRIGERANT (R410A)
COOLING
TEST CONDITION:
IEC60335-2-40
AXGT18FHTC-B
CAPACITY
CURRENT
POWER INPUT
ENERGY EFFICIENCY RATIO
: 0.5s ON / 0.5s OFF, ( ) : Number of flashing,
: 0.1s ON / 0.1s OFF
TEST CONDITION : IEC60335-2-40
MAX. PRESSURE
DIMENSIONS (W×H×D)
WEIGHT
AXGT24FHTC-B
230 V , 1Ø, 50 Hz
MAX. CURRENT
• Display mode
Problem
SUCTION
DISCHARGE
[kg]
[kW (Btu/h)]
[A]
[kW]
[W/W]
[A]
[Mpa]
[Mpa]
[mm]
[kg]
1.10
5.37 (18,300)
8.2
1.80
2.98
1.10
6.45 (22,000)
9.9
2.22
2.91
12.5
13.0
1.2
4.8
670×455×710
56
62
• Acoustic Noise Information : The maximum sound pressure level is less than 70 dB (A) for both indoor unit and outdoor unit.
According to IEC 704-1 and ISO 3744.
• COOLING CONDITION : INDOOR 27/19 °C (DB/WB) OUTDOOR 35/24 °C (DB/WB)
9386269148-EN.indd 2
2019/12/16 9:05:47
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement