Copystar CS-1635 Operation Guide

1635
2035
Operation Guide
OPERATION GUIDE
1-1
In areas of the GEEA, the available setting for the Sleep Mode to engage
is between 1 and 120 minutes, and the available setting for the Low Power
Mode to engage is any 1 minute, 5 minutes, 15 minutes, 30 minutes, 45
minutes, 60 minutes, 90 minutes or 120 minutes.
This Operation Guide is for 1635 and 2035. This Operation Guide
mentioned that the 1635 is a 16-sheet copier and the 2035 is a 20-sheet
copier.
All rights reserved. No part of this material may be reproduced or
transmitted in any form or by any means, electronic or mechanical,
including photocopying, recording or by any information storage and
retrieval system, without permission in writing from the Publisher.
Legal Restriction On Copying
•
It may be prohibited to copy copyrighted material without permission of
the copyright owner.
•
It is prohibited under any circumstances to copy domestic or foreign
currencies.
•
Copying other items may be prohibited.
Contents
Making Full use of this copier’s advanced functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Energy Star Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Safety Conventions in This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Caution Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
INSTALLATION PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
PRECAUTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
About the Operation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xix
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx
1
Name of Parts
Main Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Message Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
2
Preparations
Loading Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
3
Basic Operation
Basic Copying Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Zoom Copying. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Interrupt Copying. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Low Power Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Auto Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
4
Copying Functions
Making 2-Sided copies from various originals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Split Copy Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Making a margin space on the copies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Making copies with clean edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Copying 2 or 4 originals onto a single page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Automatic Collating of copy sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Saving on toner use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Program Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
5
System Setting
System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
System Menu Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
System Menu Operations Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Procedure for Changing the Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Checking the Total Counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
6
Job Accounting
Overview of Job Accounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Job Accounting Operations Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Department ID Code Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Deleting Department ID Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Clearing the Job Accounting Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
OPERATION GUIDE
i
Contents
Outputting the Job Accounting List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
How to set the Job Accounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Making copies in the Job Accounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
7
Optional Equipment
8
Maintenance
Cleaning the Copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Replacing the Toner Container and Waste Toner Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
9
Troubleshooting
If other trouble occurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
If one of the following indications is Displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
If paper jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-1
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-4
Functions and Settings Combination Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-5
ii
OPERATION GUIDE
Making Full use of this copier’s advanced functions
Auto Paper Selection Mode
Image Quality Selection
Auto Zoom
The copier will automatically
select the paper that is the same
size as the original
Making clear copies of photograph
originals
Reduction/Enlargement for
specified cassette sizes
Ledger: 129%
(A3: 141%)
Letter
(A4)
Statement
:64%
(A5: 70%)
Zoom Mode
2-Sided Copy Mode
Split copy
Reduction/Enlargement in the
range from 25 to 400%
Making 2-Sided Copies from
various types of originals
Copying each image of openfaced (book, etc.) or 2-Sided
originals onto separate sheets
#
25%
"
#
1
"
!
2
2
1
!
1
1
2
2
400%
Margin Mode
Border Erase Mode
Combine Mode
Shifting the image to create
margins for copies
Eliminate unnecessary borders on
the original for cleaner output
Combine two or four originals on a
single page
2
1
1
2
Collate Mode
EcoPrint
Program Function
Automatic collating can be
performed
The amount of toner consumed
can be reduced
Memorizing frequently used
settings
OPERATION GUIDE
3
2
1
3
2
1
3
2
1
3
2
1
iii
Job Accounting Mode
Language Selection
Using ID-codes to control the
number of copies mode
Changing the language used in
the message display
A full range of optional equipment is available
Document Processor
Paper Feeder
Duplex Unit
Key Counter
Printer Kit
Print server
Additional memory
iv
OPERATION GUIDE
Energy Star Program
We have determined as a participating company in the International
Energy Star Program that this product is compliant with the standards laid
out in the International Energy Star Program.
About the International Energy Star Program
International Energy Star Program has as its basic goals the promotion of
efficient energy use and the reduction of the environmental pollution that
accompanies energy consumption by promoting the manufacture and sale
of products that fulfill program standards.
International Energy Star Program standards require that copies come
equipped with a Low Power Mode where energy consumption is reduced
after a certain amount of time elapses since the device was last used, as
well as a Sleep Mode where the device automatically turns itself off after
there is no activity within a set amount of time. When the copier includes
printer and fax functions, the printer and fax must enter a Low Power Mode
where power consumption is automatically reduced after a certain amount
of time elapses since they were last used, and they must also support a
Sleep Mode where power consumption is reduced to a minimum when
there is no activity within a set amount of time. This product is equipped
with the following features as a result of its compliance with International
Energy Star Program standards.
Low Power Mode
The device automatically enters Low Power Mode when 15 minutes have
passed since the device was last used. The amount of time of no activity
that must pass before Low Power Mode is activated may be lengthened.
Refer to Low Power Mode Transition Time on page 5-22 for more
information.
Sleep Mode (If the copier has printer and/or facsimile function)
The device automatically enters Sleep Mode when 30 minutes have
passed since the device was last used. The amount of time of no activity
that must pass before Sleep Mode is activated may be lengthened. For
more information refer to Auto Sleep Setting on page 5-21.
Automatic 2-Sided Copy Function
The Energy Star Program encourages the use of 2-sided copying which
reduces the load on the environment and this device includes 2-sided
copying as a optional function. For example, by copying two 1-sided
originals onto a single sheet of paper as a 2-sided copy, it is possible to
lower the amount of paper used. For more information refer to Making 2Sided copies from various originals on page 4-2.
Paper Recycling
The Energy Star Program encourages the use of environmentally friendly
recycled paper. Your sales or service representative can provide
information about recommended paper types.
OPERATION GUIDE
v
Safety Conventions in This Guide
Please read this Operation Guide before using the copier. Keep it
close to the copier for easy reference.
The sections of this guide and parts of the copier marked with symbols are
safety warnings meant to protect the user, other individuals and
surrounding objects, and ensure correct and safe usage of the copier. The
symbols and their meanings are indicated below.
DANGER: Indicates that serious injury or even death will very
possibly result from insufficient attention to or incorrect
compliance with the related points.
WARNING: Indicates that serious injury or even death may
result from insufficient attention to or incorrect compliance with
the related points.
CAUTION: Indicates that personal injury or mechanical
damage may result from insufficient attention to or incorrect
compliance with the related points.
Symbols
The
symbol indicates that the related section includes safety warnings.
Specific points of attention are indicated inside the symbol.
..........[General warning]
..........[Warning of danger of electrical shock]
..........[Warning of high temperature]
The
symbol indicates that the related section includes information on
prohibited actions. Specifics of the prohibited action are indicated inside
the symbol.
..........[Warning of prohibited action]
..........[Disassembly prohibited]
vi
OPERATION GUIDE
The z symbol indicates that the related section includes information on
actions which must be performed. Specifics of the required action are
indicated inside the symbol.
..........[Alert of required action]
..........[Remove the power plug from the outlet]
..........[Always connect the copier to an outlet with a ground
connection]
Please contact your service representative to order a replacement if the
safety warnings in this Operation Guide are illegible or if the guide itself is
missing. (fee required)
OPERATION GUIDE
vii
Caution Labels
Labels related to safety have been attached to the product in the locations
shown below. Please observe the warnings to prevent accidents such as
burns and electrical shock while clearing paper misfeeds and adding toner.
Label2
Label3
High temperature inside this section.
There is the risk of being burned so do not
touch anything within.
High voltage generated in this
section. There is a risk of getting
shocked so do not touch anything in
this section.
Label1
High voltage generated in this
section. There is a risk of getting
shocked so do not touch
anything in this section.
Label4
Label5
Sections identified by this label operate at
high temperatures. There is the risk of being
burned so do not touch anything within.
High temperature in the upper part of this
section. There is the risk of being burned so
do not touch anything within.
Note: Do not remove any of these labels.
viii
OPERATION GUIDE
INSTALLATION PRECAUTIONS
Environment
Caution
Avoid placing the copier on or in locations which are unstable or
not level. Such locations may cause the copier to fall down or fall
over. This type of situation presents a danger of personal injury
or damage to the copier.
Avoid locations with humidity or dust and dirt. If dust or dirt
become attached to the power plug, clean the plug to avoid the
danger of fire or electrical shock.
Avoid locations near radiators, heaters, or other heat sources, or
locations near flammable items, to avoid the danger of fire.
To keep the copier cool and facilitate changing of parts and
maintenance, allow access space as shown below. Leave
adequate space, especially around the left and right sides, to
allow air to be properly ventilated out of the copier.
* Additional space will be required when the Document Processor is to be
installed.
Other precautions
Adverse environmental conditions may affect the safe operation and
performance of the copier. Install in an air-conditioned room
(recommended room temperature: around 71.6ºF (22ºC), humidity: around
60% RH) and avoid the following locations when selecting a site for the
copier.
OPERATION GUIDE
•
Avoid locations near a window or with exposure to direct sunlight.
•
Avoid locations with vibrations.
ix
•
Avoid locations with drastic temperature fluctuations.
•
Avoid locations with direct exposure to hot or cold air.
•
Avoid poorly ventilated locations.
If the floor is delicate, when this product is moved after installation, the floor
material may be damaged.
During copying, some ozone is released, but the amount will not cause any
ill effect to one's health. If, however, the copier is used over a long period
of time in a poorly ventilated room or when making an extremely large
number of copies, the smell may become unpleasant. To maintain the
appropriate environment for copy work, it is suggested that the room be
properly ventilated.
Power supply/Grounding the copier
Warning
DO NOT use a power supply with a voltage other than that
specified. Avoid multiple connections in the same outlet. These
types of situations present a danger of fire or electrical shock.
Plug the power cord securely into the outlet. If metallic objects
come in contact with the prongs on the plug, it may cause a fire
or electric shock.
Always connect the copier to an outlet with a ground connection
to avoid the danger of fire or electrical shock in case of an
electric short. If an earth connection is not possible, contact your
service representative.
Other precautions
Connect the power plug to the outlet closest to the copier.
The power supply cord is used as the main disconnect device. Ensure that
the socket/outlet is located/installed near the equipment and is easily
accessible.
Handling of plastic bags
Warning
Keep the plastic bags that are used with the copier away from
children. The plastic may cling to their nose and mouth causing
suffocation.
x
OPERATION GUIDE
PRECAUTIONS FOR USE
Cautions when using the copier
Warning
DO NOT place metallic objects or containers with water (flower
vases, flower pots, cups, etc.) on or near the copier. This type of
situation presents a danger of fire or electrical shock should they
fall inside.
DO NOT remove any of the covers from the copier as there is a
danger of electrical shock from high voltage parts inside the
copier.
DO NOT damage, break or attempt to repair the power cord. DO
NOT place heavy objects on the cord, pull it, bend it
unnecessarily or cause any other type of damage. These types
of situations present a danger of fire or electrical shock.
NEVER attempt to repair or disassemble the copier or its parts
as there is a danger of fire, electrical shock or damage to the
laser. If the laser beam escapes, there is a danger of it causing
blindness.
If the copier becomes excessively hot, smoke appears from the
copier, there is an odd smell, or any other abnormal situation
occurs, there is a danger of fire or electrical shock. Turn the
power switch OFF ({) immediately, REMOVE THE POWER
PLUG from the outlet and then contact your service representative.
If anything harmful (paper clips, water, other fluids, etc.) falls into
the copier, turn the power switch OFF ({) immediately. Next,
BE ABSOLUTELY CERTAIN to remove the power plug from the
outlet to avoid the danger of fire or electrical shock. Then contact
your service representative.
DO NOT remove or connect the power plug with wet hands, as
there is a danger of electrical shock
ALWAYS contact your service representative for maintenance
or repair of internal parts.
OPERATION GUIDE
xi
Caution
DO NOT pull the power cord when removing it from the outlet.
Pulling on the power cord may break the wires and start a fire or
cause an electrical shock. (ALWAYS grasp the power plug when
removing the power cord from the outlet.)
ALWAYS remove the power plug from the outlet when moving
the copier. If the power cord is damaged, there is a danger of fire
or electrical shock.
If the copier will not be used for a short period of time (overnight,
etc.), turn the power switch OFF ({).
If it will not be used for an extended period of time (vacations,
etc.), remove the power plug from the outlet for safety purposes
during the time the copier is not in use.
HOLD the designated parts only when lifting or moving the
copier.
For safety purposes, always REMOVE the power plug from the
outlet when performing cleaning operations.
If dust accumulates within the copier, there is a danger of fire or
other trouble. It is therefore recommended that you consult with
your service representative in regard to cleaning of internal
parts. This is particularly effective if accomplished prior to
seasons of high humidity. Consult with your service representative in
regard to the cost of cleaning the internal parts of the copier.
DO NOT leave the Document Processor open as there is a
danger of personal injury.
Other precautions
DO NOT place heavy objects on the copier or cause other damage to the
copier.
DO NOT open the front cover, turn off the power switch, or pull out the
power plug during copying.
When lifting or moving the copier, contact your service representative.
Do not touch electrical parts, such as connectors or printed circuit boards.
They could be damaged by static electricity.
DO NOT attempt to perform any operations not explained in this handbook.
CAUTION: Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
xii
OPERATION GUIDE
Do not look directly at the light from the scanning lamp. Doing so may
cause pain in the eyes or eyestrain.
Cautions when handling consumables
Caution
DO NOT attempt to incinerate the toner containers or the waste
toner box. Dangerous sparks may cause burns.
Keep the toner containers and the waste toner box out of the
reach of children.
If toner happens to spill from the toner container or the waste
toner box, avoid inhalation or ingestion, as well as contact with
your eyes and skin.
•
If you do happen to inhale toner, move to a place with fresh air and
gargle thoroughly with a large amount of water. If coughing develops,
contact a physician.
•
If you do happen to ingest toner, rinse your mouth out with water and
drink 1 or 2 cups of water to dilute the contents of your stomach. If
necessary, contact a physician.
•
If you do happen to get toner in your eyes, flush them thoroughly with
water. If there is any remaining tenderness, contact a physician.
•
If toner does happen to get on your skin, wash with soap and water.
DO NOT attempt to force open or destroy the toner containers
or the waste toner box.
Other precautions
After use, ALWAYS dispose of the toner containers and the waste toner
box in accordance with Federal, State and Local rules and regulations.
Store all consumables in a cool, dark location.
If you will not be using the copier for a prolonged period of time, remove all
paper from the cassette and the MP tray and seal in its original packaging.
OPERATION GUIDE
xiii
Laser Safety (Europe)
Laser radiation could be hazardous to the human body. For this reason,
laser radiation emitted inside this machine is hermetically sealed within the
protective housing and external cover. In the normal operation of the
product by user, no radiation can leak from the machine.
This machine is classified as Class 1 laser product under IEC 60825.
CAUTION: Performance of procedures other than those specified in this
manual may result in hazardous radiation exposure.
This label is attached to the laser scanner unit inside the machine and is
not in a user access area.
The labels shown below are attached on the rear side of the machine.
xiv
OPERATION GUIDE
Safety Instructions Regarding the Disconnection of Power (Europe)
CAUTION: The power plug is the main isolation device! Other switches
on the equipment are only functional switches and are not suitable for
isolating the equipment from the power source.
VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen
Schalter auf dem Gerät sind nur Funktionsschalter und können nicht
verwendet werden, um den Stromfluß im Gerät zu unterbrechen.
DECLARATION OF CONFORMITY
TO
89/336/EEC, 73/23/EEC and 93/68/EEC
We declare under our sole responsibility that the product to which
this declaration relates is in conformity with the following specifications.
Limits and methods of measurement for immunity
characteristics of information technology equipment
EN55024
Limits and methods of measurement for radio
interference characteristics of information technology EN55022 Class B
equipment
Limits for harmonic currents emissions
for equipment input current 16A per phase
Limitation of voltage fluctuations and flicker in lowvoltage supply systems for equipment with rated
current 16A
OPERATION GUIDE
EN61000-3-2
EN61000-3-3
Safety of information technology equipment,
including electrical equipment
EN60950
Radiation Safety of laser products, equipment
classification, requirements and user’s guide
EN60825-1
xv
Safety of Laser Beam (USA)
1. Safety of laser beam
This copier has been certified by the manufacturer to Class 1 level under
the radiation performance standards established by the U.S.DHHS
(Department of Health and Human Services) in 1968. This indicates that
the product is safe to use during normal operation and maintenance. The
laser optical system, enclosed in a protective housing and sealed within
the external covers, never permits the laser beam to escape.
2. The CDRH Act
A laser-product-related act was implemented on Aug. 2, 1976, by the
Center for Devices and Radiological Health (CDRH) of the U.S. Food and
Drug Administration (FDA). This act prohibits the sale of laser products in
the U.S. without certification, and applies to laser products manufactured
after Aug. 1, 1976. The label shown below indicates compliance with the
CDRH regulations and must be attached to laser products marketed in the
United States. On this copier, the label is on the side.
1635
2035
3. Optical unit
When checking the optical unit, avoid direct exposure to the laser beam,
which is invisible.
Shown at left is the label located on the cover of the optical unit.
xvi
OPERATION GUIDE
4. Maintenance
For safety of the service personnel, follow the maintenance instructions in
the other section of this manual.
5. Safety switch
The power to the laser unit is cut off when the upper front cover is opened.
Safety Instructions Regarding the Disconnection of Power
CAUTION: The power plug is the main isolation device! Other switches
on the equipment are only functional switches and are not suitable for
isolating the equipment from the power source.
ATTENTION: Le débranchement de la fiche secteur est le seul moyen
de mettre l’appareil hors tension. Les interrupteurs sur l’appareil ne sont
que des interrupteurs de fonctionnement : ils ne mettent pas l’appareil hors
tension.
WARNING
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: The changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
The above warning is valid only in the United States of America.
Mercury Warning
The lamp(s) inside this product contain mercury and must be recycled or
disposed of according to local, state or federal laws.
OPERATION GUIDE
xvii
Warranty (USA)
1635/2035 COPIER LIMITED WARRANTY
xviii
1
Kyocera Mita America, Inc. and Kyocera Mita Canada, Ltd. (both referred to as Kyocera)
warrants the Customer's new Multifunctional Product (referred to as MFP), and the new
accessories installed with the initial installation of the MFP, against any defects in material and
workmanship for a period of one (1) year, or 100,000 copies/prints from date of installation by
an Authorized Kyocera Dealer for the 1635/2035, whichever first occurs. In the event the MFP
or an accessory is found to be defective within the warranty period, Kyocera's only obligation
and the Customer’s exclusive remedy shall be replacement of any defective parts. It is
understood that Kyocera shall have no obligation to furnish labor.
2
This warranty is valid only as to the original retail purchaser (referred to as the Customer) of a
new Kyocera MFP in the United States of America or Canada, based upon the country of
purchase.
3
In order to obtain performance of this warranty, the Customer must immediately notify the
Authorized Kyocera Dealer from whom the product was purchased. If the Kyocera Dealer is
not able to provide service, write to Kyocera at the address below for the name and address of
the Authorized Kyocera Dealer in your area or visit our website at www.kyoceramita.com.
4
This warranty does not cover MFP’s or accessories: (a) which have become damaged due to
operator negligence, misuse, accidents, improper storage or unusual physical or electrical
stress, (b) which have used parts or supplies which are not genuine Kyocera brand parts or
supplies, (c) which have been serviced by a technician not employed by Kyocera or an
Authorized Kyocera Dealer, or (d) which have had the serial number modified, altered, or
removed.
5
This warranty does not cover process unit. Kyocera shall give the Customer a separate
warranty for this item.
6
This warranty gives the Customer specific legal rights. The Customer may also have other
rights, which vary from state to state, or province to province. Neither the seller, nor any other
person is authorized to extend the time period, or expand this warranty on behalf of Kyocera.
7
THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES AND (CONDITIONS),
EXPRESS OR IMPLIED, AND KYOCERA SPECIFICALLY DISCLAIMS ANY IMPLIED
WARRANTY (OR CONDITION) OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. THIS WARRANTY SHALL NOT EXTEND TO, AND KYOCERA SHALL NOT BE
LIABLE FOR, ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHICH MAY ARISE
OUT OF THE USE, OR INABILITY TO USE, OF THE MFP.
OPERATION GUIDE
About the Operation Guide
This Operation Guide has the following chapters:
Chapter 1 - Name of Parts
This chapter explains the names of parts.
Chapter 2 - Preparations
This chapter explains the preparations required before using the copier.
Chapter 3 - Basic Operation
This chapter describes the procedures for basic copying.
Chapter 4 - Copying Functions
This chapter describes the full-featured copying functions of the copier.
Chapter 5 - System Setting
This chapter explains how to configure various settings of the copier.
Chapter 6 - Job Accounting
This chapter explains how to manage job accounting on copier use shared
among various departments.
Chapter 7 - Optional Equipment
This chapter introduces optional equipment available for the copier.
Chapter 8 - Maintenance
This chapter describes cleaning and toner replacement.
Chapter 9 - Troubleshooting
This chapter explains how to handle printer problems that may occur, such
as paper jams.
OPERATION GUIDE
xix
Conventions
This manual uses the following conventions.
Convention
Example
Italic Typeface
Used to emphasize a key word,
phrase or references to
additional information.
Close the front cover.
Refer to Toner Container Replacement
on page 3-3.
Courier Typeface
Used to denote messages or
names displayed on the
operation panel.
System menu will be displayed.
Bold Typeface
Used to indicate operation panel
keys.
Press [Start].
Notes
Used to provide additional or
useful information about a
function or feature.
NOTE: For information about storing the
pin, refer to step 10.
Important
Used to provide important
information.
Caution
Cautions are statements that
suggest mechanical damage as
a result of an action.
CAUTION: Do not pull the cassette out
Used to alert users to the
possibility of personal injury.
WARNING: High voltage is present
in the charger section.
Warning
xx
Description
IMPORTANT: Ensure paper is not
folded, curled, or damaged.
when holding the front of the machine.
OPERATION GUIDE
Name of Parts
1 Name of Parts
This chapter identifies copier parts and operation panel keys.
•
•
•
OPERATION GUIDE
Main Body .................................................................... 1-2
Operation Panel ........................................................... 1-4
Message Display .......................................................... 1-6
1-1
Name of Parts
Main Body
1
2
3
8
4
9
10
7
6
1
Original Cover
2
Output Tray
3
Operation Panel
4
Cassette
5
Paper Width Guides
6
Paper Stopper
7
Left Cover Handle
8
MP Tray (multi-purpose tray)
9
MP Tray Extension
5
10 Paper Width Guides
1-2
OPERATION GUIDE
Name of Parts
19
11
20
12
15
16
14 17
18
13
20
11 Platen
12 Original Size Indicator Plate
13 Left Cover
14 Waste Toner Box
15 Toner Container Release Lever
16 Toner Container
17 Cleaning shaft
18 Front Cover
19 Power Switch
20 Handles
OPERATION GUIDE
1-3
Name of Parts
Operation Panel
Inch specifications
36
37
30
33
34
31
28 27
24
26 25 23
11
18
17 14
9
7
6
4
3
2
1
35
32
29
20
22
19
21
16 13 12
8
15
10
1
Start Key (Indicator)
2
Stop/Clear Key
3
Reset Key
4
Energy Saver Key
5
Numeric keys
6
Interrupt Key
7
Job Accounting Key
8
V
9
U
5
10 %/OK Key
11 100%/Auto% Key
12 Paper Supply Indicator
13 Paper Selection Key
14 Paper Supply Level Indicator
15 Paper Misfeed Indicator
16 MP Indicator
17 No. of Copies/Zoom Display
18 Message Display
19 Original Size Key
20 EcoPrint Key
21 Auto Exposure Key
22 Exposure Adjustment Key/Exposure Display
1-4
OPERATION GUIDE
Name of Parts
Metric specifications
36
37
30
33
34
31
28 27
24
26 25 23
11
18
17 14
9
7
6
4
3
2
1
35
32
29
20
22
19
21
16 13 12
8
15
10
5
23 Attention Indicator
24 Error Indicator
25 Add Toner Indicator
26 Maintenance Indicator
27 Image Quality Selection Key
28 Printer Key (Indicator)
Press this to switch the message display between copier mode and
printer mode, when optional printer kit is installed.
29 2-sided Key
30 Mixed Original Size Key
31 Combine Key
32 Split Key
33 Program Key
34 Border Erase Key
35 Media Type Key
36 Collate Key
37 Margin Key
OPERATION GUIDE
1-5
Name of Parts
Message Display
The message display on the operation panel shows:
•
Status information, the messages listed below which are displayed
during normal operation.
•
Error codes, when the printer requires the operator’s attention, refer to
If one of the following indications is Displayed on page 9-5.
Status Information
Message
Meaning
Self test
The copier is performing self-diagnostics after power-up.
Please wait.
The copier is warming up and is not ready.
When the copier is switched on for the first time, this message will take
approximately 20 seconds.
Ready to copy.
The copier is ready to copy.
Error codes
Refer to If one of the following indications is Displayed on page 9-5.
System Menu (the mode after warm-up processing has been completed or
[Reset] pressed)
The copier has been set at the factory to automatically select a
magnification ratio of 1:1 for the same size of paper as the original in the
Auto Mode with the No. of Copies at “1” and
for the Image Quality.
NOTE: The Default Settings can be changed in the System Menu.
In the case where an optional cassette is present, the cassette selected in
the System Menu can be changed. (Refer to Selected Cassette on page
5-14.)
The Image Quality Mode selected in the System Menu can be changed.
(Refer to Original Image Quality on page 5-9.)
The Default Setting for the copy density can be changed to the Auto.
(Refer to Initial Density on page 5-9.)
Auto Clear function
After the copy has been produced and a fixed interval (10 to 270 seconds)
has elapsed, the copier will automatically revert to the state it was in when
warm-up processing was completed.(However, the copy density mode and
the Image Quality will not revert back to their original state. Copies can still
be repeatedly produced with the same Copy Mode, No. of Copies, copy
density and other settings if the Auto clear function has not been activated.
1-6
OPERATION GUIDE
Name of Parts
NOTE: Please refer to Auto Clear Time on page 5-21. Turning Off the
Auto clear Function Auto Clear Setting on page 5-20 for information on
changing the time interval before the Auto clear function activates.
Custom Sizes
Paper and original sizes that are not displayed on the Operation Panel can
be registered as Custom Sizes. (Inputting Custom Size on page 2-9.)
Automatic Cassette Switching Function
If multiple cassettes contain the same size paper and the paper in one
cassette runs out during copying, the automatic cassette switching
function will switch paper feed from the empty cassette to the other
cassette that still contains paper.
NOTE: An optional cassette is required to do this.
The Automatic Cassette Switching Function can also be turned off if not
needed. (Refer to Auto Cassette Switching on page 5-15.)
The paper has to be oriented in the same direction.
OPERATION GUIDE
1-7
Name of Parts
1-8
OPERATION GUIDE
Preparations
2 Preparations
This chapter explains the preparations required before using
the copier.
•
OPERATION GUIDE
Loading Paper .............................................................. 2-2
2-1
Preparations
Loading Paper
Paper can be loaded into the copier via the cassette or MP tray.
Before Loading Paper
When you open a new package of
paper, fan through the sheets to
separate them slightly prior to
loading. If the paper is curled or
folded, straighten it before
loading. Paper that is curled or
folded may cause paper jams.
IMPORTANT: If you copy onto used paper (paper already used for
copying), do not use paper that is stapled or clipped together. This may
damage the copier or cause poor image quality.
Set the paper in the cassette with
the side which faced the top of its
packaging facing up.
IMPORTANT: When using paper that has been run through a copier
before, check it to make sure that all staples and paper clips have been
removed. Attempting to copy paper that has fasteners attached may result
in poor images or malfunctions.
Straighten out any creases or curls in the paper before loading it into the
cassette. Failure to straighten out creases and curls may lead to paper
misfeeds.
Leaving paper out of its package
under high temperature and high
humidity conditions may lead to
problems caused by ambient
moisture. After loading paper into
cassette, store the remaining
paper sealed in the paper storage
bag. Also, before leaving the
copier in disuse for a prolonged
period of time, remove the paper
from the cassette and seal it in the paper storage bag to protect it from
moisture.
Special Types of Paper
The size of the paper to be accommodated by the cassette or MP tray can
2-2
OPERATION GUIDE
Preparations
be set. (Refer to Inputting MP Tray Size and Media Type on page 2-7 and
Inputting Custom Size on page 2-9.)
Loading Paper into the Cassette
Standard paper, recycled paper and colored paper can be loaded into the
cassette. Up to 300 sheets of standard paper (80 g/m2) or 100 sheets of
thick paper (90 to 105 g/m2) can be set. Sizes which can be loaded are:
Ledger to Statement, Oficio 2, A3 to A5R and Folio.
IMPORTANT: When loading paper for the first time or when changing
paper sizes, use the operation panel to indicate the cassette size. (Refer
to Cassette Size Detection on page 2-5.) This can also be set in the
System Menu. (Refer to Inputting Custom Sizes on page 5-15.)
[Inch specifications]
When using sizes that are Oficio 2, A3 to A5R, set the size. (Refer to
Inputting Custom Sizes on page 5-15.)
[Metric specifications]
When using sizes that are Oficio 2, Ledger to Statement, set the size.
(Refer to Inputting Custom Sizes on page 5-15.)
1
Pull the cassette all the way out
towards you.
NOTE: Do not pull out several
cassettes at one time.
2
Push down on the cassette base
plate and secure it.
3
Grasp the Width Size Adjustment
tab and match the paper size to
the Width Guide.
The paper sizes are impressed in
the cassette.
OPERATION GUIDE
2-3
Preparations
4
Grasp the Length Size
Adjustment tab and match the
paper size to the Length Guide.
The paper sizes are impressed in
the cassette.
IMPORTANT: When setting
Ledger paper, move the length
size adjustment tab to the right
side end and push it down as
shown in the illustration below.
5
Set the paper straight from the
upper part.
IMPORTANT: Be careful not to
bend and crease the paper when
inserting it into the cassette.
Creases in the paper may lead to
paper misfeeds.
(1)
The maximum paper limit
indicator (1) is on the Width
Guide. Make sure that the paper
loaded is below the maximum
limit indicator.
When loading paper into the cassette, set it so that the side which was
facing upwards in its packaging faces up.
Always match the Width and Length Guides to the paper size before
loading the paper. Failure to do so may result in paper skewing or jamming.
Make sure that the Length and Width Guides are flush against the paper.
If there is space between the Guide and the paper, adjust the Length or
Width Guide to eliminate it. If the Guides are not firmly set against the
paper, a size that is different from that in the cassette may be displayed on
the Paper Selection display.
2-4
OPERATION GUIDE
Preparations
When the paper has become wrinkled from moisture, set the paper so that
the wrinkled side is towards the Length Guide.
NOTE: When loading paper into the cassette, set it so that the side that
is to be copied faces upwards.
6
Set the accompanying paper
sheet so that the paper size set in
the cassette can be identified
from the front of the cassette.
7
Gently push in the cassette.
NOTE: When the copier will not be used for a long period of time, remove
the paper from the cassette, put it in a storage bag and seal the bag in
order to protect the paper from humidity.
Cassette Size Detection
Set the Size Detection on the operation panel to match the size of the
paper loaded in the cassette. The copier has been set at the time of
shipping for automatic detection in inch units for inch specifications, or in
centimeter units (A⋅B columns) for metric specifications.
1
Press [Paper Selection] for 3 seconds. The System Menu will be
displayed.
2
Press U or V to display the
19.Cassette1Size.
System Menu:
19.Cassette1Size
NOTE: When setting the size of the optional cassette (2 to 4), display
20.Cassette2Size, 21.Cassette3Size and 22.Cassette4Size.
OPERATION GUIDE
3
Press [OK].
4
Press U or V and select Auto Detect mm, AutoDetect inch or
Oficio 2.
5
Press [OK]. The display will blink and copying can begin.
2-5
Preparations
Setting paper on the MP tray
In addition to standard paper and recycled paper, special paper (45 to 160
g/m2) can also be set.
Up to 50 sheets of standard (80 g/m2) paper (25 sheets of Ledger R, Legal
R or A3, B4, Oficio 2, Folio) can be set. The paper sizes that can be used
are: Ledger R to Statement, A3 to B6R, A6R, Oficio 2, Cardstock, Folio R,
8k, 16k, 16k R, Executive, ISO B5, Envelope #10, Envelope #9, Monarch,
Envelope #6.75, Envelope C5, Envelope C4, Envelope DL,
OuhukuHagaki, Youkei 2gou and Youkei 4gou.
When making copies onto special paper, always use the MP tray.
NOTE: The types of special paper that can be loaded and their
respective quantities are as follows.
Color Paper: 50 sheets
Postcards: 10 sheets
Vellum Paper/Thick Paper (45 to 160 g/m2): 50 sheets to 5 sheets
(quantity differs depending on paper size and thickness)
IMPORTANT: Set the paper size and type according to that set in the
Paper Feed. (Refer to Inputting MP Tray Size and Media Type on page 27.)
This can also be set in the System Menu. (Inputting MP Tray Size and
Media Type on page 2-7)
When using non-standard size paper, register the paper size as Custom.
(Refer to Inputting Custom Size on page 2-9.)
When loading the thick paper (90 to 160 g/m2) or vellum paper (45 to 63 g/
m2), set the Media Type. (Refer to Selecting Special Media Types on page
2-10.)
1
Open the MP tray.
NOTE: When setting paper
greater than Letter/A4R, pull out
the MP tray extension to match
the paper size.
2-6
OPERATION GUIDE
Preparations
2
Adjust the paper width guide to
the width of the paper to be set.
3
Use the paper width guide to push
the paper in until it reaches the
point where it stops.
IMPORTANT: Always straighten out postcards and other types of thick
paper that are curved before using them. There may be cases in which the
feeding operation cannot be carried out due to the quality of the paper.
When loading paper into the MP Tray, set it so that the side which was
facing upwards in its packaging faces downwards. If the front of the paper
is bent backwards, straighten it out before setting it.
Check to make sure there are no creases, etc. in the paper. Creases in the
paper may lead to paper misfeeds.
Inputting MP Tray Size and Media Type
Adjust the paper in the MP Tray and register the paper size using the
Operation Panel. And specifies the media type.
OPERATION GUIDE
1
Press [Paper Selection] for 3 seconds. The System Menu will be
displayed.
2
Check to make sure that 23.MPTray
Config is displayed and then press [OK].
System Menu:
23.MPTray Config
2-7
Preparations
3
Press U or V and select the paper size. The paper sizes displayed are as
given in the table below. In the case of the selection of Other Standards
or Custom Size, proceed to Inputting Other Standards on page 2-9 or
Inputting Custom Size on page 2-9.
Inch specifications
Metric specifications
Universal size
Universal size
Ledger R
A3 R
Legal R
A4 R
Letter R
A4
Letter
A5 R
Statement R
B4 R
Other Standards
B5 R
Customized Size
Folio R
Other Standards
Customized Size
IMPORTANT: Use the illustration
as a reference when setting the
paper in the ## R in the MP Tray.
2-8
4
Press [OK].
5
Press U or V and select the media type. The media types displayed are
as given below.
Plain
Letterhead
Transparency
Colour
Preprinted
Prepunched
Labels
Envelope
Bond
Cardstock
Recycled
Thick Paper
Rough
High Quality
OPERATION GUIDE
Preparations
Vellum
Custom (1 to 8)
6
Press [OK]. The display will blink and the copier will return to the System
menu.
7
Press U or V to display 00.Setting done.
8
Press [OK]. Copying can be begun.
Inputting Other Standards
1
Select the Other Standards. (Refer to Inputting MP Tray Size and
Media Type on page 2-7.)
2
Press [OK].
3
Press U or V and select the paper size. The paper size displayed are as
given below.
Inch specifications
A3 R, A4 R, A4, A5 R, A6 R, B4 R, B5 R, B5, B6 R, Folio R, Oficio
2, Executive, ISO B5, Envelope #10, Envelope #9, Monarch,
Envelope #6.75, Envelope C5, Envelope C4, Envelope DL,
Hagaki, OufukuHagaki, Youkei 2gou, Youkei 4gou, 8k R, 16k R,
16k
Metric specifications
A6 R, B5, B6 R, Ledger R, Legal R, Letter R, Letter, Statement
R, Oficio 2, Executive, ISO B5, Envelope #10, Envelope #9,
Monarch, Envelope #6.75, Envelope C5, Envelope C4, Envelope
DL, Hagaki, OufukuHagaki, Youkei 2gou, Youkei 4gou, 8k R, 16k
R, 16k
4
Proceed to Step 4 (Inputting MP Tray Size and Media Type on page 2-7).
Inputting Custom Size
OPERATION GUIDE
1
Select the Customized Size. (Refer to Inputting MP Tray Size and
Media Type on page 2-7.)
2
Press [OK].
3
Press U or V and input the Length Size.
3.88 to 11.63(")/98 to 297(mm): The range
in which setting is possible.
4
Press [OK].
5
Press U or V and input the Width Size.
5.88 to 17.00(")/148 to 432(mm): The range
in which setting is possible.
Non-std size L
297mm
Non-std size W
148mm
2-9
Preparations
6
Proceed to Step 4 (Inputting MP Tray Size and Media Type on page 2-7).
Selecting Special Media Types
Select the media type when copying on special types of paper such as
thick paper (1) and vellum paper (2). When the media type has been
selected, the copier will change the fixing temperature to match the paper.
1
Press [Media Type] and select the media type. The indicator for the media
type selected will light up.
2
Proceed with the copying operation.
NOTE: When media type has been selected, the copying speed is
reduced.
2-10
OPERATION GUIDE
Basic Operation
3 Basic Operation
This chapter explains the following operations.
•
•
•
•
•
OPERATION GUIDE
Basic Copying Procedure............................................. 3-2
Zoom Copying .............................................................. 3-5
Interrupt Copying.......................................................... 3-7
Low Power Mode.......................................................... 3-8
Auto Sleep Mode.......................................................... 3-9
3-1
Basic Operation
Basic Copying Procedure
1
Warm-up
Turn ON (|) the Power Switch.
Start will light up after warm up
has been completed.
2
Setting the Original
Set the copy original on the glass
platen. Align the original so that
the left rear corner is flush against
the original size indicator.
NOTE: Please refer to Setting Originals in the Document Processor on
page 7-3 for the procedure used for placing the original when using the
optional Document Processor.
3
Selecting Functions
Select any of the various functions available.
•
•
•
•
•
•
•
•
Making enlarged and reduced copies (Refer to page3-5.)
Interrupt Copying (Refer to page3-7.)
Making 2-Sided copies from various types of originals (Refer to
page4-2.)*
Split Copy Modes (Refer to page4-6.)
Making a margin space on the copies (Refer to page4-8.)
Making copies with clean edge (Refer to page4-10.)
Fitting the image of either two or four originals onto a single copy
page (Refer to page4-12.)
Automatic Collating of copy sets (Refer to page4-19.)
*. The Duplex Unit (option) is necessary.
4
Paper Selection
When Automatic Paper Selection is lit, a paper size identical to the original
will be automatically selected. Press [Paper Selection] in order to select
a different paper size to copy.
NOTE: It is possible to turn off the Automatic Size Selection function.
(Refer to Cassette Selection on page 5-13.)
3-2
OPERATION GUIDE
Basic Operation
It is also possible to select the cassette that is to be automatically given
priority for use. (Refer to Selected Cassette on page 5-14.)
5
Image Quality Selection
The Image Quality can be selected to match the type of original to be
copied. Press [Image Quality Selection] to light up the Image Quality
Mode to be used.
•
•
•
: Use this when the original contains a mixture of text and
photos.
: Use this when copying a photograph.
: Use this when copying originals that contain a large amount
of text.
NOTE: The Image Quality Mode selected in the System Menu can be
changed. (Refer to Original Image Quality on page 5-9.)
The density of each of the Image Quality Modes can be adjusted. (Refer
to Text + Photo Mode Exposure Adjustment on page 5-11, Photo
Exposure Adjustment on page 5-11 and Text Exposure Adjustment on
page 5-12.)
When horizontal lines stand out in Photo Mode, select Dithering (Refer to
Photo Processing on page 5-12). Note, however, that the images will be
rougher when Dithering is used.
6
Adjusting Copy Exposure
The Copy Exposure (density) is adjusted manually. To make the copy
darker, press [Exposure Adjustment] on the right and move the exposure
scale to the right. To make the copy lighter, press [Exposure Adjustment]
on the left and move the exposure scale to the left.
Pressing [Auto Exposure] will detect the copy exposure and set it to the
optimal setting.
NOTE: The exposure can be adjusted when the overall exposure is too
light or too dark using Auto Exposure. (Refer to Auto Exposure
Adjustment on page 5-11.)
The Copy Exposure Adjustment can be set to Auto Exposure Mode when
setting the Default Settings. (Refer to Initial Density on page 5-9.)
Pressing [Exposure Adjustment] will move the scale in increments of
0.5 and allow even finer adjustment of the exposure. (Refer to Exposure
Steps on page 5-10.)
When the Photo Mode has been selected using Image Quality Selection,
Auto Exposure cannot be selected.
7
Setting the Number of Copies
Press the numeric keys to input and display the desired number of copies.
Up to 999 copies can be set at a single time.
OPERATION GUIDE
3-3
Basic Operation
NOTE: The maximum number of copies that can be made at one time
can also be restricted. (Refer to Copy Limit on page 5-19.)
8
Start Copying
Press [Start]. When the Start indicator lights green copying can be begun.
9
Completion of the Copying
Procedure
The finished copy will be ejected
into the output tray.
IMPORTANT: Up to 250 standard paper copies (80 g/m2) can be stored.
Note, however, that the number of copies that can be stored may differ with
the condition of the paper used.
CAUTION: When the
copier will not be used for a
period of time, such as at
night, turn off the power
switch. When it will not be
used for longer periods of
time such as during long
holiday periods, remove the
plug from the outlet in the
interest of safety.
3-4
OPERATION GUIDE
Basic Operation
Zoom Copying
Auto Zoom Ratio Selection Mode
Original images are reduced or
enlarged according to the
selected paper size.
Ledger: 129%
(A3: 141%)
Letter
(A4)
Statement: 64%
(A5: 70%)
IMPORTANT: When this is to be used as the default Mode, set the Auto
Sizing on page 5-15 to on.
1
Set the original.
The original’s size will be
automatically detected.
2
Press [100%/Auto%] to light up the Auto% indicator.
3
Press [Paper Selection] and select the paper.
4
Press [Start] to begin copying.
Zoom Mode
With this mode, the zoom ratio
can be set between 25% and
400% (25% to 200% with the
document processor) in 1%
increments.
25%
400%
IMPORTANT: When the zoom ratio is changed in the Auto Paper Select
Mode, the zoom ratio for the selected paper size is also changed to match
the zoom ratio.
OPERATION GUIDE
3-5
Basic Operation
1
Set the original.
2
Press U, V or [%/OK].
The copy magnification will be displayed in the No. of Copies display and
“%” will light up.
3
Change the zoom percentage displayed using U or V.
The percentage can also be input using the numeric keys.
3-6
4
Press [OK]. After the zoom percentage has been confirmed the display
changes back to the No. of Copies display.
5
Press [Start] to begin copying.
OPERATION GUIDE
Basic Operation
Interrupt Copying
Interrupt Copying is useful when
you want to make a copy of a
different original at different
settings during copying
operations. After the Interrupt
Copy has been produced, the
copying operation resumes at the
same settings in effect prior to the
interruption.
OPERATION GUIDE
1
Press [Interrupt]. The Interrupt indicator
will blink. It will stay lit when the Interrupt
operation becomes possible.
2
Temporarily storing the original during copy operations.
3
Set the original for the Interrupt
operation and copy it.
4
After the Interrupt copy has been produced, pressing [Interrupt] will cause
the display to light up. Replace it with the original that had been put aside
and press [Start] to resume copying.
Interrupt copy
is available.
3-7
Basic Operation
Low Power Mode
Pressing [Energy Saver] will put the copier into a resting state even when
the Power Switch is ON. The No. of Copies display on the Operation Panel
will change to “- - -”, the Energy Saver indicator will light up and all other
indicators and message display will be turned off.
Press any key on the Operation Panel or open and close the Original
Cover in order to resume copying operations. In the case where the
optional Document Processor is installed, placing an original in the
Document Processor will also revert the copier to the state where copies
can be made. The recovery time before copies can be made is within 10
seconds.
NOTE: A function to automatically enter the Low Power Mode after a set
interval in which no copies have been produced has passed is also
included. (Refer to Low Power Mode Transition Time on page 5-22.)
3-8
OPERATION GUIDE
Basic Operation
Auto Sleep Mode
The Auto Sleep Function is a function that automatically turns the copier
off after a set period of time (1 to 240 minutes) has passed. “-” is displayed
in the No. of Copies display and all other indicators and message display
will be turned off.
This has been set to 30 minutes at shipping.
NOTE: In the Sleep Mode state, the supply of electrical power to
everything except the operating section is stopped. When the Power
Switch is turned off, the supply of power to everything, including the
operating section, is stopped.
The No. of Copies display will show a “-” for approximately 5 seconds
after the Power Switch has been turned off.
Press [Energy Saver] in order to resume copying operations. The
recovery time before copies can be made is less than 20 seconds.
Auto Sleep Mode
The Auto Sleep Function is a power-saving function that automatically puts
the copier into Sleep Mode when no copying operations have been
performed for a set period of time.
In the case of copiers, the amount of time spent idling rather than copying
is large, so the amount of power consumed during idle operation makes up
the largest share of their power usage. The consumption of power during
idling or when someone forgets to turn the copier off after work can be
reduced through the copier unit automatically entering the Sleep Mode and
the electric bill reduced as a result.
NOTE: The time interval before the Auto Sleep Mode engages can be
changed. (Refer to Sleep Mode Transition Time on page 5-22.)
The Auto Sleep Mode can be deselected. (Refer to Auto Sleep Setting on
page 5-21.)
OPERATION GUIDE
3-9
Basic Operation
3-10
OPERATION GUIDE
Copying Functions
4 Copying Functions
This chapter explains the following topics.
•
•
•
•
•
•
•
•
OPERATION GUIDE
Making 2-Sided copies from various originals.............. 4-2
Split Copy Modes ......................................................... 4-6
Making a margin space on the copies.......................... 4-8
Making copies with clean edges................................. 4-10
Copying 2 or 4 originals onto a single page ............... 4-12
Automatic Collating of copy sets ................................ 4-19
Saving on toner use ................................................... 4-21
Program Function....................................................... 4-22
4-1
Copying Functions
Making 2-Sided copies from various originals
Copies of both sides can be made from open-faced originals as well as
from 2-in-1 originals.
NOTE: The Duplex Unit (option) is necessary.
Making 2-Sided copies from a 2-Sided original
Front and Back side copies are
made in the same way as duplex
copies.
Original
Finished Product
Left-Right Binding *1
Left-Right Binding
Left-Right Binding *2
Top Binding *2
*1
2-Sided Copy reverse side
rotation setting: OFF
*2
2-Sided Copy reverse side
rotation setting: ON
Top Binding *1
Top Binding
Left-Right Binding
Top Binding
NOTE:
[Inch specifications]
The paper sizes that can be used are Ledger, Legal, Letter, Letter R and
Statement sizes. A3 to A5R sizes can also be used when Custom Size is
set.
The Duplex Unit (option) is necessary.
[Metric specifications]
The paper sizes that can be used are from A3 to A5R. Ledger, Legal,
Letter, Letter R and Statement sizes can also be used when Custom Size
is set.
The Duplex Unit (option) is necessary.
4-2
OPERATION GUIDE
Copying Functions
Making 2-Sided copies from an open-faced (book, etc.) original
The double-page original of
books, magazines, etc. can be
copied onto both sides of the
paper by pressing [Start] one
time.
Original
Finished Product
Left Binding
Spread →
Spread: Front and Back
1
1 2
2
Spread →
Spread: Front and Back
Right Binding
2
1
2 1
NOTE:
[Inch specifications]
The original sizes that can be used are Ledger and Letter. The paper
sizes that can be used are Letter. A3, B4, A4R, B5R and A5R Original
sizes can also be used when Custom Size is set.
The paper size can be changed and the magnification adjusted to fit the
size of the paper.
[Metric specifications]
The original sizes that can be used are A3, B4, A4R, B5R and A5R. The
paper sizes that can be used are A4 and B5. Ledger and Letter Original
sizes can also be used when Custom Size is set.
The paper size can be changed and the magnification adjusted to fit the
size of the paper.
Making 2-Sided copies from one-sided originals
Original
Copy
#
"
!
#
"
2-Sided Copy one side of an
original to the front and back
sides. When the number of pages
is an odd number, the back side of
the last page is copied as a blank
page.
!
NOTE: The back side copy can also be rotated 180 degrees and copied.
Original Left/Right Binding → Finished Left/Right Binding:
Setting the 2-Sided Copy reverse side setting to OFF will result in the
reverse side being copied as is.
OPERATION GUIDE
4-3
Copying Functions
1
Original
Copy
(1)
ghi
abc
def
Original Left/Right Binding →
Finished Top Binding:
Setting the 2-Sided Copy
reverse side setting to ON will
result in the reverse side being
copied after being rotated 180
degrees. The finished copy is
bound at the top, and each page
spread copied in the same
direction.
ghi
def
abc
(2)
ghi
abc
def
Set the original.
NOTE: The underside Rotate Copy can also be set in the System Menu.
(Refer to 2-Sided Copy Reverse Side Rotation Setting on page 4-5.)
The value set in the System Menu will inherit the value that is set at the
time when the copy is made.
2
Press [2-sided], select the type of original, and select
,
or
to light up the corresponding display.
3
Input the number of sets of copies using the numeric keys.
4
Press [Start]. The copier will begin
scanning the original.
Scanning.
When an original has been set in the
optional Document Processor copying will
begin automatically.
4-4
OPERATION GUIDE
Copying Functions
When the original has been set on the
platen and the scanning of the original
completed, Place next original. is
displayed and the 2-Sided Copy display
blinks. When this occurs, carry out the
following procedure.
5
Place next
original.
Replace the original with the next one and press [Start].
The copier will scan the original.
6
If there are no more originals to be scanned, press [2-sided] or [OK]. The
copier will begin copying.
2-Sided Copy Reverse Side Rotation Setting
Follow the procedure below to change the rotation setting for the reverse
side when making 2-Sided copies.
OPERATION GUIDE
1
Press [2-sided] for 3 seconds. The System
Menu for the reverse side setting of 2-Sided
Copies will be displayed.
2
Press U or V and select Rotation On in the case where the reverse side
is to be rotated or Rotation Off when it isn’t to be rotated.
3
Press [OK]. The display will blink and the copier will return to the state
where copying can be continued.
42.Duplex 2nd
Rotation On
4-5
Copying Functions
Split Copy Modes
Split copy from book originals
Copy books, magazines, etc. with
two facing pages of an openfaced original onto separate
sheets of paper.
Original
1
Copy
2
2
1
NOTE:
[Inch specifications]
The original sizes that can be used are Ledger and Letter. The paper
sizes that can be used are Letter. A3, B4, A4R, B5R and A5R Original
sizes can also be used when Custom Size is set.
The paper size can be changed and the magnification adjusted to fit the
size of the paper.
[Metric specifications]
The original sizes that can be used are A3, B4, A4R, B5R and A5R. The
paper sizes that can be used are A4 and B5. Ledger and Letter Original
sizes can also be used when Custom Size is set.
The paper size can be changed and the magnification adjusted to fit the
size of the paper.
Split copy from 2-sided originals
The original is copied separately
as simplex pages.
Original
1
Copy
1
2
2
4-6
OPERATION GUIDE
Copying Functions
1
Set the original.
2
Press [Split], select the type of original, and select
light up the corresponding display.
3
Press [Start]. The copier will begin copying.
or
to
In the case where Collate Copies has been set, proceed to Step 4.
OPERATION GUIDE
4
Replace the original with the next one and press [Start]. The copier will
scan the original.
5
If there are no more originals to be scanned, press [OK]. The copier will
begin copying.
4-7
Copying Functions
Making a margin space on the copies
Standard Margin
[Inch specifications]
The position of the image of the
original is shifted for copying and
a 0.13/0.25/0.38/0.50/0.63/0.75
(") (1/8-inch increments) width
binding margin created.
Original
Copy
[Metric specifications]
The position of the image of the
original is shifted for copying and
a 1 to 18 mm (1 mm increments)
width binding margin created.
NOTE: If the left width of the Binding Margin is set when setting the 2Sided Copy, the right side of the Binding Margin will be set automatically
for the reverse side by the 2-sided copy rotational setting in the case
where it is rotated.
1
Set the original.
.
IMPORTANT: Place the original so that the side to be set for the Margin
shift is on the right side (on the left side, in the case of the optional
Document Processor) and check its position after setting it. If the original
is placed in the wrong direction, the Binding Margin will not be produced in
the position set.
NOTE: The Binding Margin can also be set in the System Menu. (Refer
to Setting the Margin on page 4-9.)
The value set in the System Menu will inherit the value that is set at the
time when the copy is made.
4-8
2
Press [Margin]. The Margin indicator will light up.
3
Press [Start]. The copier will begin copying.
OPERATION GUIDE
Copying Functions
Setting the Margin
Use the procedure given below to change the Margin.
1
Press [Margin] for 3 seconds. The System
Menu for the Margin will be displayed.
2
Press U or V and select the binding margin width.
43.Stitch Width
1mm
[Inch specifications]
0.13/0.25/0.38/0.50/0.63/0.75("): the range in which the margin can
be set.
[Metric specifications]
A margin from 1 to 18 (mm) can be set.
3
OPERATION GUIDE
Press [OK]. The display will blink and the copier will return to the state
where copying can be continued.
4-9
Copying Functions
Making copies with clean edges
Erasing blemishes from edges of copies (Sheet erase mode)
[Inch specifications]
Use this to remove the dark
shading that appears around
sheet originals during copying.
Select the border width to be
erased from among 0.13/0.25/
0.38/0.50/0.63/0.75 ("). ((A) in the
illustration is the Border Width.)
Original
Copy
(A)
(A)
[Metric specifications]
Use this to remove the dark shading that appears around sheet originals
during copying. Select the border width to be erased from 1 to 18 (mm).
((A) in the illustration is the Border Width.)
Erasing blemishes from the edges and middle of copies made from books
(Book erase mode)
[Inch specifications]
Original
Use this to get a clean copy of
thick books. Select the outer
border width from among 0.13/
0.25/0.38/0.50/0.63/0.75 ("). The
center border width will be 2-times
that of the outer border width ((A)
in the illustration is the outer
border width and (B) is the center
border width.)
(A)
(B)
Copy
(A)
[Metric specifications]
Use this to get a clean copy of thick books. Select the outer border width
from 1 to 18 (mm). The center border width will be 2-times that of the outer
border width ((A) in the illustration is the outer border width and (B) is the
center border width.)
NOTE: Only standard sizes can be used as the Original size.
4-10
OPERATION GUIDE
Copying Functions
1
Set the original.
NOTE: The Border Width can also be set in the System Menu. (Refer to
Setting the Border Width on page 4-11.)
The value set in the System Menu will inherit the value that is set at the
time when the copy is made.
2
Press [Border Erase] and select the type of border erase to be performed
to light up the
3
or
indicator.
Press [Start]. The copier will begin copying.
Setting the Border Width
Use the procedure given below to change the Border Width.
1
Press [Border Erase] for 3 seconds. The
System Menu for the Border Width will be
displayed.
2
Press U or V and select the border width.
44.Border Erase
1mm
[Inch specifications]
Select from 0.13 ("), 0.25 ("), 0.38 ("), 0.50 ("), 0.63 (") or 0.75 (").
[Metric specifications]
Select from 1 to 18 (mm).
3
OPERATION GUIDE
Press [OK]. The display will blink and the copier will return to the state
where copying can be continued.
4-11
Copying Functions
Copying 2 or 4 originals onto a single page
The sizes of 2-sheet or 4-sheet
originals can be reduced and
copied together onto a single
sheet. In addition, the borders of
each original can be separated
with a solid or dotted line.
2
1
1
2
NOTE: Only standard paper sizes and originals can be used for this.
2 in 1
2 sheets of originals can be
copied onto a single sheet. If
used together with 2-Sided
Copy, 4 sheets of originals can
be copied onto both sides of a
single sheet.
(Follow the order shown in
illustrations 1 → 2 in placing the
originals on the platen.)
Original
Copy
The directions for setting the original and the finished copy are as follows.
4-12
OPERATION GUIDE
Copying Functions
When the original is set on the platen
Original Setting Direction
Finished Product
1
1
1
1
OPERATION GUIDE
4-13
Copying Functions
When the original is set in the Document Processor
Original Setting Direction
Finished Product
4-14
OPERATION GUIDE
Copying Functions
4 in 1
4 sheets of originals can be
copied onto a single sheet. If
used together with 2-Sided
Copy, 8 sheets of originals can
be copied onto both sides of a
single sheet.
(Follow the order shown in
illustrations 1 → 2 → 3 → 4 in
placing the originals on the
platen.)
Original
Copy
1
2
3
4
1
3
2
4
4
3
2
1
Portrait
4
3
2
1
1
2
3
4
1
3
2
4
Landscape
The directions for setting the original and the finished copy are as follows.
When the original is set on the platen
Original Setting Direction
Finished Product
1
11
1
1
1
OPERATION GUIDE
4-15
Copying Functions
When the original is set in the Document Processor
Original Setting Direction
Finished Product
11
1
1
1
Set the original.
NOTE: The 4 in 1 layout setting (refer to 4 in 1 Layout Order on page 417) and the setting of border lines when setting Combine mode (refer to
Setting the Combine mode Border Lines on page 4-17) can also be set in
the System Menu.
The value set in the System Menu will inherit the value that is set at the
time when the copy is made.
2
Press [Combine] to light up the
3
Input the number of sets of copies using the numeric keys.
4
Press [Start]. The copier will begin reading
in the original.
or
indicator.
Scanning.
When an original has been set in the
optional Document Processor copying will
begin automatically.
4-16
OPERATION GUIDE
Copying Functions
When the original has been set on the
platen and the scanning of the original
completed, Place next original. is
displayed and the Combine indicator blinks.
When this occurs, carry out the following
procedure.
Place next
original.
5
Replace the original with the next one and press [Start]. The copier will
read in the original.
6
If there are no more originals, press [Combine] or [OK]. The copier will
begin copying.
4 in 1 Layout Order
Follow the procedure below to change the order in which pages are to be
laid out within the copied page when making 4 in 1 copies.
1
Press [Combine] for 3 seconds. The
System Menu will be displayed.
2
Confirm that 45.4 in 1 Layout is displayed and then press [OK].
3
Press U or V and select the
layout.
45.4 in 1 Layout
Portrait 1
Portrait 1
Portrait 2
1 2
1 3
3 4
2 4
Landscape 1
2
4
1
3
4
Landscape 2
1
2
3
4
Press [OK]. The display will blink and copying can be begun.
Setting the Combine mode Border Lines
Use the procedure given below to change the Combine mode Border
Lines.
OPERATION GUIDE
1
Press [Combine] for 3 seconds. The System Menu will be displayed.
2
Press U to display 46.Combine Border.
3
Press the [OK].
4
Press U or V and select the type of border line.
System menu:
46.Combine Border
4-17
Copying Functions
Off
Solid
Dotted
5
4-18
Press [OK]. The display will blink and the copier will return to the state
where copying can be continued.
OPERATION GUIDE
Copying Functions
Automatic Collating of copy sets
It is possible to Collate the number
of copy sets needed from multiple
sheets of originals.
NOTE: Whether or not to
collate while changing the
direction for each set at the
time of collating can be
changed using the System
Menu. (Refer to Rotate Collate
Setting on page 5-19.)
No Collating
Copy
1
1
1
Original
2
2
2
3
2
1
3
3
3
Collating
Copy
3
2
1
Original
3
2
1
3
2
1
3
2
1
1
Set the original.
NOTE: When an original is set in the optional Document Processor, the
Collate indicator will light and Collate Copies will be set. In this case,
proceed to Step 3.
2
Press [Collate].
3
Input the number of sets of copies using the numeric keys.
4
Press [Start]. The copier will begin reading
in the original.
Scanning.
When an original has been set in the
optional Document Processor copying will
begin automatically.
OPERATION GUIDE
4-19
Copying Functions
When the original has been set on the
platen and the scanning of the original
completed, Place next original. is
displayed and the Collate display blinks.
When this occurs, carry out the following
procedure.
4-20
Place next
original.
5
Replace the original with the next one and press [Start]. The copier will
read in the original.
6
If there are no more originals, press [Collate] or [OK]. The copier will begin
copying.
OPERATION GUIDE
Copying Functions
Saving on toner use
Setting EcoPrint will result in a reduced amount of toner being consumed.
Use this to make test copies or copies where high-quality printing is not
required. Refer to EcoPrint on page 5-10 for instructions on how to select
or deselect EcoPrint in the System Menu.
The image will become slightly
lighter.
OPERATION GUIDE
EcoPrint
Not Set
1
Set the original.
2
Press [EcoPrint].
3
Press [Start]. The copier will begin copying.
EcoPrint
Set
4-21
Copying Functions
Program Function
Copy settings that are frequently used can be registered and then recalled
by pressing [Program]. Even types of copies can be stored.
Registering a program
1
Set the Copy Mode to be registered.
2
Press [Program] for 3 seconds.
3
Input the program number (0 to 9) using the numeric keys and press the
[Program] key for 3 seconds.
The display of the number input will blink 2 times and the program will be
registered.
NOTE: If the same number as a program already registered is input, the
prior program is overwritten.
Using programmed setting to make copies
4-22
1
Press [Program].
2
Press U or V, select the number of the program to be used and then press
[OK]. Input can also be done using the numeric keys.
3
Set the original and press [Start]. The copy will be made using the
program that has been set.
OPERATION GUIDE
System Setting
5 System Setting
This chapter covers how to configure various settings of the
copier using the menus on the operation panel.
•
•
•
•
•
OPERATION GUIDE
System Menu ............................................................... 5-2
System Menu Items...................................................... 5-2
System Menu Operations Procedures ......................... 5-2
Procedure for Changing the Default Settings............... 5-8
Checking the Total Counter ........................................ 5-24
5-1
System Setting
System Menu
The copier will enter System Menu after warm up has been completed or
when [Reset] has been pressed. The settings automatically set for the
copier in System Menu are called the Default Settings. These settings can
be freely changed to match the usage of the copier.
System Menu Items
The following are the System Menu Items.
Change the settings as necessary in order to achieve the most efficient use
of the copier. The factory default setting is indicated by an asterisk (*).
System Menu
Items
5-2
Description
Available settings
Reference
Page
01.Copy Status
Outputs the content of the Default Settings.
---
5-8
02.Language
Set the language of the message display.
[Inch specifications]
English*
Francais
Espanol
Japanese
Portugues
[Metric specifications]
English
Deutsch
Francais
Espanol
Italiano
5-8
03.Image Quality
Sets the manuscript image quality that will be
selected at the time the copier is turned on.
Text + Ph Dens.*
Photo Density
Text Density
5-9
04.Initial Dens.
Sets the copy exposure at the time the copier is
turned on to Manual or Automatic.
There will be no display when Photo Density has
been selected in 03.Image Quality.
Manual*
Auto
5-9
05.EcoPrint
Selects the initial value of the EcoPrint Mode when
the power is turned on. The initial value of the Eco
Mode can be set to on (Enable). Exposures will be
lighter and less toner will be consumed when the
EcoPrint Mode is used.
On: Enabled
Off: Disabled*
5-10
06.Density steps
Changes the number of the adjustment steps for the
copy’s exposure. 0.5 - Setting this step enables even
finer adjustment of the exposure.
1 Step*
0.5 Step
5-10
07.Auto Density
Adjusts the overall exposure of the copy when Auto
Exposure Mode is used.
1(lightest) to 7(darkest)
(*4)
5-11
08.Text+Ph Dens.
Adjusts the central exposure value for the copier’s
manual exposure (Text and Photo).
1(lightest) to 7(darkest)
(*4)
5-11
09.Photo Density
Adjusts the central exposure value for the copier’s
manual exposure (Photo).
1(lightest) to 7(darkest)
(*4)
5-11
OPERATION GUIDE
System Setting
System Menu
Items
Description
Available settings
Reference
Page
10.Text Density
Adjusts the central exposure value for the copier’s
manual exposure (Text).
1(lightest) to 7(darkest)
(*4)
5-12
11.ReduceStreaks
It is possible to make black streaking less noticeable
when it appears when using the optional Document
Processor.
Off*
Weak
Strong
5-12
12.OptimizePhoto
Setting this to Error Diffusion when copying originals
with text and photos and Dithering when copying
originals with mainly photos will result in clearer
images.
ErrorDiffusion*
Dither Matrix
5-12
13.OptimizBackgr
The background color can be lightened when it is
found to be too dark after copying.
1(lightest) to 5(darkest)
(*3)
5-13
14.Initial Paper
Selects whether the cassette with the same size of
paper as the original size will be automatically
selected or whether a selected cassette level is to be
used.
Auto*
DefaultCassette
5-13
15.AutoSel Paper
Specifies the media type when the copier
automatically selects the paper.
Plain*
Transparency
Rough
Vellum
Labels
Recycled
Preprinted
Bond
Cardstock
Color (Colour)
Prepunched
Letterhead
Thick paper
Envelope
High Quality
Custom 1 to 8
5-14
16.DefaultCasset
Selects the cassette that is automatically given
priority for use.
Manual paper feeding cannot be set using the
Selected cassette function.
Cassettes 2 to 4 will be displayed only when the
optional Paper Feeder is installed.
Cassette 1*
Cassette 2
Cassette 3
Cassette 4
5-14
17.AutoCassetSet
Switches feeding automatically to a cassette holding
paper of the same size/orientation and copying
continues when the paper in the cassette being used
runs out.
This will be displayed when the optional Paper
Feeder is installed.
Disting. paper
Not dist. paper*
5-15
18.PriorAutoZoom
Sets whether or not to use automatic magnification
(zoom/reduction percentage) when a paper cassette
has been selected.
On: Enabled
Off: Disabled*
5-15
OPERATION GUIDE
5-3
System Setting
System Menu
Items
19.Cassette1Size
20.Cassette2Size
21.Cassette3Size
22.Cassette4Size
23.MPTray Config
5-4
Description
Available settings
Reference
Page
Automatically detects the paper size in the supply
cassettes (1 to 4).
When it is to be detected in inches, set this to
AutoDetect inch; when paper size is to be detected in
centimeters, (A⋅B columns) set this to Auto Detect
mm and when Oficio 2 size is to be used set this to
Oficio 2.
Cassettes 2, 3 and 4 will be displayed only when the
optional Paper Feeder is installed.
Auto Detect mm
(*Metric specifications)
AutoDetect inch (*Inch
specifications)
Oficio 2
2-5
Sets the size of paper to be manually fed in.
Paper Size
[Inch specifications]
Universal size*
Ledger R
Legal R
Letter R
Letter
Statement R
Other Standards
Customized Size
[Metric specifications]
Universal size*
A3 R
A4 R
A4
A5 R
B4 R
B5 R
Folio R
Other Standards
Customized Size
Media Type
Plain*
Transparency
Preprinted
Labels
Bond
Recycled
Rough
Vellum
Letterhead
Colour
Prepunched
Envelope
Cardstock
Thick Paper
High Quality
Custom (1 to 8)
2-7
OPERATION GUIDE
System Setting
System Menu
Items
24.Custom Size 1
25.Custom Size 2
26.Casst1MedType
27.Casst2MedType
Description
[Inch specifications]
A3 R
A4 R
A4
A5 R
B4 R
B5R
B5
B6 R
A6 R
Hagaki
11 × 15" R
Folio R
Oficio 2
Customized Size
YYY × XXX (mm)
Y-direction: 98 to 297mm
X-direction: 148 to 432mm
[Metric specifications]
B5 R
B6 R*
A6 R
Cardstock
Ledgr R
Legal R
Letter R
Letter
Statement R
Oficio 2
11 × 15" R
Customied Size
YYY × XXX (")
Y-direction: 3.88 to 11.63"
X-direction: 5.88 to 17"
5-15
Specifies the media type to the cassettes (1 to 4) .
Cassette 2, 3 and 4 will be displayed only when the
optional Paper Feeder is installed.
Plain*
Recycled
Preprinted
Bond
Rough
Color (Colour)
Letterhead
Prepunched
High Quality
Custom 1 to 8
5-17
Sets the paper weights and 2-sided copying to the
Custom paper. 2-sided copying will be displayed only
when the optional Duplex Unit is installed.
Paper weights
Extra Heavy
Heavy 3
Heavy 2
Heavy 1
Normal 3
Normal 2*
Normal 1
Light (Vellum)
2-sided copying
On: Enabled*
Off: Disabled
5-17
29.Casst4MedType
31.CustmMedType2
32.CustmMedType3
33.CustmMedType4
34.CustmMedType5
35.CustmMedType6
36.CustmMedType7
Reference
Page
Sets the size to be set to the Custom size (1 to 2).
This makes it possible to set the size that do not
appear on the operation panel.
28.Casst3MedType
30.CustmMedType1
Available settings
37.CustmMedType8
OPERATION GUIDE
5-5
System Setting
System Menu
Items
5-6
Description
Available settings
Reference
Page
38.Hagaki/A6RDet
Select the paper size when copying an original
document of non-standard size.
Hagaki
A6 R*
5-18
39.B4R/Folio Det
Select the paper size when copying an original
document of non-standard size.
B4 R
Folio R*
5-18
40.11x15" Detect
When the size of original document is 11 x 15", the
original document is automatically zoomed.
On
Off*
5-18
41.Copy Limit
Limits the number of copies or sets of copies that can
be made at one time.
1 to 999 (*999)
5-19
42.Duplex 2nd
Rotates the paper 180 degrees and copies it when
both sides of a sheet are to be copied.
This will not be displayed when the optional Duplex
Unit is not installed.
Rotation On
Rotation Off*
4-5
43.Stitch Width
Sets the initial value for the Binding Margin.
[Inch specifications]
0.13/0.25/0.38/0.50/
0.63/0.75 (") (*0.25)
[Metric specifications]
1 to 18 (mm) (*6)
4-9
44.Border Erase
Sets the initial value for the border width that will be
lightened to remove shadows from the sheet or book.
[Inch specifications]
0.13/0.25/0.38/0.50/
0.63/0.75 (") (*0.25)
[Metric specifications]
1 to 18 (mm) (*6)
4-11
45.4 in 1 Layout
Sets the layout for the order in which the originals will
appear in the 4-in-1 Layout mode.
Portrait 1*
Portrait 2
Landscape 1
Landscape 2
4-17
46.Combine Border
Selects the type of borderline to be used in the
Layout mode.
Off*
Solid
Dotted
4-17
47.Rotate/Offset
Sets the copier so that each copy set is rotated and
collated when it is collate copied.
On: Rotational Collating
Enabled
Off: Rotational Collating
Disabled*
5-19
48.Auto Rotation
Sets of copied documents are output landscape/
portrait alternately, allowing easy separation of each
set from the other.
On: Enabled*
Off: Disabled
5-20
49.Silent mode
Shortens the amount of time the internal motor
continues to run after the copy is produced. Use this
setting in cases when the motor noise is bothersome.
0, 5, 10, 15, 30
(seconds) (*10)
5-20
50.Auto Clear
Sets the copier so that automatic clearing is executed
after a set amount of time has elapsed after the copy
is produced. (Refer to Auto Clear function on page 16.)
On: Enabled*
Off: Disabled
5-20
OPERATION GUIDE
System Setting
System Menu
Items
Description
Available settings
Reference
Page
51.Auto Sleep
The Auto Sleep mode will be entered after a set
period of time has passed after the final copy has
been produced or during which no operations have
been performed.
If the Auto Sleep function interferes with your copy
operations, disable the function. Before disabling the
Auto Sleep function, you may want to try lengthening
the amount of time before the Auto Sleep function
engages (Sleep Mode Transition Time).
On: Enabled*
Off: Disabled
5-21
52.AutoClearTime
Sets the time interval prior to the automatic operation
of the Auto Clear function when On (Enable) has
been selected as the 50.Auto Clear setting.
This will not be displayed when 50.Auto Clear is set
to Off.
10 to 270 (10-second
units) (*90)
5-21
53.LowPower Time
Sets the time interval prior to the automatic
engagement of the Low Power mode after copy
operations have been completed.
1, 5, 15, 30, 45, 60, 90,
120, 180, 240 (minutes)
(*15)
5-22
54.AutoSleepTime
Sets the time interval prior to the automatic operation
of the Auto Sleep function when On (Enable) has
been selected as the 51.Auto Sleep setting.
This will not be displayed when 51.Auto Sleep is set
to Off.
1, 5, 15, 30, 45, 60, 90,
120, 180, 240 (minutes)
(*30)
5-22
55.Alarm
The Alarm can be set to sound when a key on the
Operation Panel is pressed or in cases when errors
occur, etc.
On: Enabled (sound
alarm)*
Off: Disabled (no alarm)
5-23
56.CoverageRepo
Prints out a report that shows the number of copies
made and the average amount of toner used
(blackness ratio %) for each paper size.
---
5-23
System Menu Operations Procedures
Follow the procedure listed below to operate in the System Menu.
1
Press [Exposure Adjustment] on both
sides for 3 seconds. System Menu will be
displayed.
2
Press U or V and select System Menu Items.
System Menu:
00.Setting done
NOTE: Each of System Menu Items can be selected by pressing the
numeric keys.
Refer to "Procedure for Changing the Default Settings" regarding the
following.
3
OPERATION GUIDE
After completing each operation, press U or V to display 00.Setting
done.
5-7
System Setting
NOTE: The message display will return to the Ready to copy. by
pressing [Reset].
You can cancel the setting by pressing [Stop/Clear].
4
Press [OK].
Procedure for Changing the Default Settings
The procedure for changing each of the items in the System Menu is
described below.
User Status Report
Outputs a list of the values set for the System Menu items.
NOTE: Check to make sure that Letter/A4 size paper is loaded in the
cassette.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 01.Copy
Status.
3
Press [OK].
4
Press U or V and select Yes.
5
Press [OK]. The report will be output.
Sample: User Status
Report
System Menu:
01.Copy Status
USER COPY SETTING LIST
F00 : [ - - - - - - - - - - - - - - - - - - - - - - - -] ==========
F01 : [ - - - - - - - - - - - - - - - - - - - - - - - -] ==========
F02 : [ - - - - - - - - - - - - - - - - - - - - - - - -] =======
F03 : [
=======
] ==========
F04 : [
=====
] ==========
F05 : [
====
] =======
F07 : [
======
] ==========
F08 : [
======
] ==========
F09 : [
=
] ==========
F10 : [
=
] ========
=
] ==========
=
] ========
F11 : [
F12 : [
F13 : [
======
F14 : [
======
F15 : [
======
] ==========
] ==========
F16 : [
=====
] ==========
F17 : [
====
] =========
F18 : [
======
] ==========
] ==========
Message Language
You can select the language of the message display by following the
procedure given below.
5-8
OPERATION GUIDE
System Setting
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 02.Language.
3
Press [OK].
4
Press U or V. The display cycles through the available selection in the
System Menu:
02.Language
following order:
Inch specifications
5
Metric specifications
English
English
Francais
Deutsch
Espanol
Francais
Japanese
Espanol
Portugues
Italiano
Press [OK]. The display will return to that of Step 2.
Original Image Quality
Sets the original image quality that will be selected at the time the copier is
turned on.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 03.Image
Quality.
3
Press [OK].
4
Press U or V and select Text+Ph Dens, Photo Density or Text
Density.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
03.Image Quality
Initial Density
Sets the copy density at the time the copier is turned on to Manual or
Automatic.
OPERATION GUIDE
5-9
System Setting
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 04.Initial
Dens.
3
Press [OK].
4
Press U or V and select Manual or Auto.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
04.Initial Dens.
EcoPrint
Selects the initial value of EcoPrint when the power is turned on. The initial
value of the EcoPrint can also be set to on (Enable).
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 05.EcoPrint.
3
Press [OK].
4
When EcoPrint is to be used as the initial value press V and select On
(Enable).
5
Press [OK]. The display will return to that of Step 2.
System Menu:
05.EcoPrint
Exposure Steps
Changes the number of steps for the copy’s exposure.
5-10
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 06.Density
steps.
3
Press [OK].
4
Press U or V and select 1 Step, or 0.5 Step.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
06.Density steps
OPERATION GUIDE
System Setting
Auto Exposure Adjustment
Adjusts the overall exposure of the copy when Auto Exposure Mode is
used.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 07.Auto
Density.
3
Press [OK].
4
Press U or V and select an exposure from 1 to 7.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
07.Auto Density
Text + Photo Mode Exposure Adjustment
Adjusts the median exposure value of the copy for the Text + Photo
original.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 08.Text+Ph
Dens.
3
Press [OK].
4
Press U or V and select an exposure from 1 to 7.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
08.Text+Ph Dens.
Photo Exposure Adjustment
Adjusts the median exposure value of the copy for the Photo original.
OPERATION GUIDE
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 09.Photo
Density.
3
Press [OK].
System Menu:
09.Photo Density
5-11
System Setting
4
Press U or V and select an exposure from 1 to 7.
5
Press [OK]. The display will return to that of Step 2.
Text Exposure Adjustment
Adjusts the median exposure value of the copy for the Text original.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 10.Text
Density.
3
Press [OK].
4
Press U or V and select an exposure from 1 to 7.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
10.Text Density
Processing to Reduce Black Line
It is possible to make black line less noticeable when it appears when using
the optional Document Processor. Using processing to reduce black line
decreases the reproduction quality of small characters, so it is
recommended that the copier normally be used at the factory default
setting.
NOTE: When Photo Mode has been selected in Image Quality Mode,
processing to reduce black line is not possible.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
11.ReduceStreaks.
3
Press [OK].
4
Press U or V and select Off, Weak or Strong.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
11.ReduceStreaks
Photo Processing
Select the processing method for photo originals.
5-12
OPERATION GUIDE
System Setting
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
12.OptimizePhoto.
3
Press [OK].
4
Press U or V and select ErrorDiffusion, or Dither Matrix.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
12.OptimizePhoto
Background Adjustment
The background can be lightened when it is found to be too dark after
copying.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
13.OptimizBackgr.
3
Press [OK].
4
Press U or V and select a background color exposure from 1 to 5.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
13.OptimizBackgr
Cassette Selection
Selects whether the cassette with the same size of paper as the original
size will be automatically selected or whether a selected cassette level
(fixed) is to be used.
OPERATION GUIDE
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 14.Initial
Paper.
3
Press [OK].
4
Press U or V and select Auto, or DefaultCassette.
System Menu:
14.Initial Paper
5-13
System Setting
5
Press [OK]. The display will return to that of Step 2.
Selecting Media Types for Automatic Paper Selection
Specifies the type of media when the copier automatically selects the copy
paper according to the size of the original. The type of media can be
specified from the following types of paper supported.
Plain, Transparency, Rough, Vellum, Labels, Recycled, Preprinted, Bond,
Cardstock, Color (Colour), Prepunched, Letterhead, Thick paper,
Envelope, High Quality and Custom 1-8
When Plain is selected in the following example, the copier looks for the
cassette or MP tray in which the paper of the matching type (plain) and size
(of the original document) is loaded and begins copying.
NOTE: To assign media type to cassette according to the type of the
media loaded, refer to Selecting Media Type (Cassettes 1 to 4) on page 517 for details.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 15.AutoSel
Paper.
3
Press [OK].
4
Press U or V to select the desired media type.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
15.AutoSel Paper
Selected Cassette
When the optional Paper Feeder is installed, priority will be assigned to the
cassette that is selected automatically. Manual paper feeding cannot be
set using the Selected Cassette function.
5-14
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
16.DefaultCasset.
3
Press [OK].
4
Press U or V and select the cassette to be given priority for use.
System Menu:
16.DefaultCasset
OPERATION GUIDE
System Setting
NOTE: The range of selection will vary in accordance with the number of
cassettes installed.
5
Press [OK]. The display will return to that of Step 2.
Auto Cassette Switching
When the optional Paper Feeder has been installed, select whether or not
to use the Auto Cassette Switching function.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
17.AutoCassetSet.
3
Press [OK].
4
Press U or V and select Disting. paper when the Auto Cassette
Switching function is to be used and Not dist. paper when it will not
be used.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
17.AutoCassetSet
Auto Sizing
Sets whether or not to use automatic sizing (zoom/reduction percentage)
when a paper cassette has been selected.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
18.PriorAutoZoom.
3
Press [OK].
4
Press U or V and select On when the Automatic Sizing function is to be
used and Off when copies are to be taken at a 1:1 ratio.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
18.PriorAutoZoom
Inputting Custom Sizes
Sizes that are not displayed on the Operation Panel are registered as
Custom Sizes.
OPERATION GUIDE
5-15
System Setting
The setting of Custom Size 1 is shown here as an example. To set Custom
Size 2 select 25.Custom Size 2 in the System Menu and then perform
the same settings.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display the 24.Custom
Size1.
3
Press [OK].
4
Press U or V and select the size. The paper sizes displayed are as shown
in the table below. When selecting Irregular Sizes, carry out the following
procedure. In the case of the selection of other sizes, proceed to Step 9.
Inch specifications
System Menu:
24.Custom Size 1
Metric specifications
A3 R
B5 R
A4 R
B6 R
A4
A6 R
A5 R
Cardstock
A6 R
Ledger R
B4 R
Legal R
B5 R
Letter R
B5
Letter
B6 R
Statement R
11×15" R
Oficio 2
Folio R
11×15" R
Cardstock
Customized Size
Customized Size
5-16
5
Press [OK]. The Width can be input after 2 blinks.
6
Press U or V and input the Length Size.
3.88 to 11.63(")/98 to 297 (mm): The range
in which setting is possible.
7
Press [OK]. The Width can be input after 2 blinks.
Non-std size L
297mm
OPERATION GUIDE
System Setting
8
Press U or V and input the Width Size.
5.88 to 17.00(")/148 to 432 (mm): The range
in which setting is possible.
9
Press [OK]. The display will return to that of Step 2.
Non-std size W
148mm
Selecting Media Type (Cassettes 1 to 4)
Specifies the media type to the cassette 1 to 4. These cassettes support
the following media type.
Plain, Preprinted, Bond, Recycled, Rough, Letterhead, Color (Colour),
Prepunched, High Quality and Custom 1-8
The setting of Cassette 1 is shown here as an example, select
27.Casst2MedType, 28.Casst3MedType and 29.Casst4MedType in
the System Menu before selecting Cassette 2, 3 and 4 (option),
respectively.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
26.Casst1MedType.
3
Press [OK].
4
Press U or V to select the desired media type.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
26.Casst1MedType
Specifying the Paper Weight and 2-sided Copying to Custom Paper
Assigns one of the following paper weights to the Custom paper. And you
can determine whether 2-sided copying is allowed to the custom paper. Up
to 8 custom paper are configurable.
Extra Heavy, Heavy3, Heavy2, Heavy1, Normal3, Normal2, Normal1 and
Light (Vellum)
The setting of Custom 1 is shown here as an example, select
31.CustmMedType2, 32.CustmMedType3, 33.CustmMedType4,
34.CustmMedType5, 35.CustmMedType6, 36.CustmMedType7 and
37.CustmMedType8 in the System Menu before selecting Custom 2, 3,
4, 5, 6, 7 and 8, respectively.
NOTE: 2-sided Copying setting will be displayed only when the optional
Duplex Unit is installed.
Refer to the following media types and weights (g/m2)
OPERATION GUIDE
5-17
System Setting
•
•
•
•
•
•
•
•
Extra Heavy - OHP sheet
Heavy 3 - from 171 g/m2 to 209 g/m2
Heavy 2 - from 136 g/m2 to 170 g/m2
Heavy 1 - from 106 g/m2 to 135 g/m2
Normal 3 - from 91 g/m2 to 105 g/m2
Normal 2 - from 76 g/m2 to 90 g/m2
Normal 1 - from 60 g/m2 to 75 g/m2
Light (Vellum) - from 60 g/m2 to 64 g/m2
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
30.CustmMedType1.
3
Press [OK].
4
Press U or V to select the desired media type.
5
Press [OK]. When the optional Duplex Unit is not installed, the display will
return to that of Step 2.
6
Press U or V and select On when the 2-sided Copying is to be used and
Off when it will not be used.
7
Press [OK]. The display will return to that of Step 2.
System Menu:
30.CustmMedType1
Auto Detect Originals
Allows you to predetermine what paper size is selected for printing when
copying an original document of non-standard sizes (Refer to below). This
feature is applicable when the size of the original is either Hagaki, A6R,
B4R or Folio. The menu also provides the means to determine whether 11
x 15" is recognized as a standard size.
The setting of Hagaki or A6R is shown here as an example, select
39.B4R/Folio Det and 40.11x15" Detect in the System Menu
before selecting B4R and 11 x 15", respectively.
NOTE: This setting is only available for metric models.
5-18
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 38.Hagaki/
A6RDet.
System Menu:
38.Hagaki/A6RDet
OPERATION GUIDE
System Setting
3
Press [OK].
4
Press U or V to select the paper size to set up.
When the size of the original document is Hagaki or A6R, choose Hagaki
to copy it on Hagaki size or A6 R to copy it on A6R size.
When the size of the original document is B4R or Folio, choose B4 R to
copy it on B4R size or Folio R to copy it on Folio size.
When the size of the original document is 11 x 15" (computer form), you
can choose whether the original document is automatically zoomed to the
currently selected paper (On) or the copier halts and prompts you to
investigate the size of the original document (Off).
5
Press [OK]. The display will return to that of Step 2.
Copy Limit
Limits the number of copies or sets of copies that can be made at one time.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 41.Copy Limit.
3
Press [OK].
4
Press U or V and set the copy limit value (1 to 999). This can also be input
using the numeric keys.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
41.Copy Limit
Rotate Collate Setting
Set whether or not to change the direction for each copy set and collate it
when collating copies.
OPERATION GUIDE
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 47.Rotate/
Offset.
3
Press [OK].
4
Press U or V and select On to change the direction for each copy set and
collate it or Off to collate in the same direction.
System Menu:
47.Rotate/Offset
5-19
System Setting
5
Press [OK]. The display will return to that of Step 2.
Selecting Auto Rotation
The auto rotation delivers the sets of copied documents perpendicular to
each other, allowing an easy separation of each set from the others.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 48.Auto
Rotation.
3
Press [OK].
4
Press U or V and select On when the sets of copied documents are to be
rotated and Off when no rotation is to be performed.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
48.Auto Rotation
Silent Mode Transition Time
Shortens the amount of time the internal motor continues to run after the
copy is produced. Use this setting in cases when the motor noise is
bothersome.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 49.Silent
mode.
3
Press [OK].
4
Press U or V and select the amount of time for transition into Silent Mode.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
49.Silent mode
Auto Clear Setting
Set whether or not to automatically return the copier to Ready to copy.
state when copying is finished.
1
5-20
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
OPERATION GUIDE
System Setting
2
Press U or V to display 50.Auto Clear.
3
Press [OK].
4
Press U or V and select On in the case where the transition to Auto Clear
is to be made or Off when it is not.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
50.Auto Clear
Auto Sleep Setting
Set whether or not to automatically enter Sleep Mode when copying is
completed or after operations have been finished.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 51.Auto Sleep.
3
Press [OK].
4
Press U or V and select On in the case when the transition to Auto Sleep
is to be made or Off when it is not.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
51.Auto Sleep
NOTE: If the Auto Sleep function interferes with your copy operations,
disable the function. Before disabling the Auto Sleep function, you may
want to try lengthening the amount of time before the Auto Sleep function
engages.
Auto Clear Time
Set the time interval to automatically return the copier to Ready to copy.
state when copying is finished.
OPERATION GUIDE
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
52.AutoClearTime.
3
Press [OK].
System Menu:
52.AutoClearTime
5-21
System Setting
4
Press U or V and select a time interval from 10 to 270 (seconds).
NOTE: Set the time interval to a longer length of time in the case where
the copier is used often and to a shorter time interval when it is used
infrequently.
This can be set when the Auto Clear setting has been set to On. (Refer to
Auto Clear Setting on page 5-20.)
5
Press [OK]. The display will return to that of Step 2.
Low Power Mode Transition Time
Set the time interval from the time operations end to the automatic
engagement of the Low Power Mode.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 53.LowPower
Time.
3
Press [OK].
4
Press U or V and select a time interval from 1 minute to 240 minutes.
System Menu:
53.LowPower Time
NOTE: The time intervals available are: 1, 5, 15, 30, 45, 60, 90, 120,
180 and 240 minutes.
5
Press [OK]. The display will return to that of Step 2.
Sleep Mode Transition Time
Set the time interval for automatically entering Sleep Mode when copying
is completed or after operations have been finished.
5-22
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
54.AutoSleepTime.
3
Press [OK].
4
Press U or V and select a time interval from 1 minutes to 240 minutes.
System Menu:
54.AutoSleepTime
OPERATION GUIDE
System Setting
NOTE: This can be set when the Auto Sleep setting has been set to On.
(Refer to Auto Sleep Setting on page 5-21.)
The time intervals that can be set are 1, 5, 15, 30, 45, 60, 90, 120, 180
and 240 minutes.
5
Press [OK]. The display will return to that of Step 2.
Alarm
The Alarm can be set to sound when a key on the Operation Panel is
pressed or in cases when errors occur, etc.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display 55.Alarm.
3
Press [OK].
4
Press U or V and select On in the case where the alarm is to be sounded
or Off when it isn’t to be sounded.
5
Press [OK]. The display will return to that of Step 2.
System Menu:
55.Alarm
Toner Coverage Report
Output the report that shows the number of copies made and the average
concentration of toner used for each paper size.
1
Display the System Menu. (Refer to System Menu Operations
Procedures on page 5-7.)
2
Press U or V to display
56.CoverageRepo.
System Menu:
56.CoverageRepo
NOTE: Check to make sure that Letter/A4 size paper is loaded in the
cassette.
OPERATION GUIDE
3
Press [OK].
4
Press U or V and select Yes.
5
Press [OK]. The report will be output and the display will return to that of
Step 2.
5-23
System Setting
Sample: Toner
Coverage Report
TONER COVERAGE REPORT
### Machine No. :
XXXXXXXXX
<LAST PAGE COVERAGE>
1.14
<COPY COVERAGE>
PAGE SIZE
A3
B4
A4
B5
A5
B6
POST
OTHER
USAGE
PAGES
COVERAGE(%)
10
0
9
0
0
0
0
0
12.25
0.00
2.89
0.00
0.00
0.00
0.00
0.00
9.34
(AVE.)
Checking the Total Counter
The Total Count can be viewed on the Operation Panel. A Counter Report
can also be output.
1
Press [Stop/Clear] for 3 seconds. The Copy Count will be displayed on the
message display.
NOTE: Pressing on [Start] while the Copy Count is displayed will output
the Counter Report. Check to make sure that Letter/A4 paper is available
in the cassette before printing out the Counter Report.
Sample: Counter
Report
= = = = COUNT REPORT = = = =
### Machine No. :
XXXXXXXXX
<Total count>
485
<Output count>
B/W
<Scan count>
Document
2
5-24
Copy
Printer
20
465
Total
485
Copy
16
The copier will return to the state where copying can be continued after the
Copy Count has been displayed.
OPERATION GUIDE
Job Accounting
6 Job Accounting
This chapter explains how to manage job accounting on copier
use shared among various departments.
•
•
•
•
•
•
•
•
OPERATION GUIDE
Overview of Job Accounting......................................... 6-2
Job Accounting Operations Procedures....................... 6-2
Department ID Code Registration ................................ 6-3
Deleting Department ID Codes .................................... 6-3
Clearing the Job Accounting Count.............................. 6-4
Outputting the Job Accounting List............................... 6-4
How to set the Job Accounting..................................... 6-5
Making copies in the Job Accounting ........................... 6-6
6-1
Job Accounting
Overview of Job Accounting
The Job Accounting allows you to manage the number of copies for each
department through the setting of the Department ID Code separately for
each department.
This copier has the following features available through the Department ID
Code.
•
•
•
A maximum of 100 Sections can be managed.
ID Codes can be set from 0 to 99999999 for a maximum of 8 digits.
The accumulated totals of pages copied according to ID Code can be
printed out on paper.
The factory default setting is indicated by an asterisk (*).
Job Accounting
Available
settings
Description
On: Set
Off: No Setting*
Reference
Page
01.JobAccounting
In order to carry out Job Accounting, set this to on
(set), Set this to oFF (no setting) when Department
Management is not needed.
6-5
02.Register code
Registers the Department ID Code up to the line. Up
to 100 sections can be registered as Department ID
Codes.
03.Delete code
Deletes Department ID Codes that will not be used
anymore.
04.Count Clear
Batch-clears the copy count after a set amount of
copies have been managed. The counts cannot be
deleted separately in accordance with the Department
ID Codes.
6-4
05.Print list
Outputs the number of copies produced by
Department in a report format.
6-4
6-3
Yes: Delete
No: No Deletion
6-3
Job Accounting Operations Procedures
Follow the procedure listed below to operate the Job Accounting.
1
Press both of [Exposure Adjustment] for 3
seconds while pressing on [Job
Accounting]. Job Accounting: will be
displayed.
2
Press U or V and select each of the mode displays.
Job Accounting:
00.Set Completed
NOTE: Refer to each of the following setting procedures and make the
settings.
Each of the Modes can be selected by pressing the numeric keys.
6-2
OPERATION GUIDE
Job Accounting
3
After completing each setting, press U or V
to display 00.Set Completed.
4
Press [OK].
Job Accounting:
00.Set Completed
Department ID Code Registration
A Department ID Code of up to 8 digits can be entered.
1
Display the Job Accounting. (Refer to Job Accounting Operations
Procedures on page 6-2.)
2
Press U or V to display 02.Register
code.
3
Press [OK].
4
Input the Department ID Code to be registered (up to a maximum of 8
digits) using numeric keys.
Job Accounting:
02.Register code
Number from 0 to 99999999 can be input.
NOTE: If a mistake is made during input it can be cleared by pressing
[Stop/Clear] and the value reentered.
5
Press [OK]. The code that was input will flash on and off.
6
After confirming the code that was input, press [OK]. The display will return
to that of Step 2.
NOTE: If an existing Department ID Code is attempted to be registered,
an error will occur and Already registered. will display in the
message display. In this case, register a different Department ID Code.
Deleting Department ID Codes
Deleting a registered Department ID Code.
OPERATION GUIDE
1
Display the Job Accounting. (Refer to Job Accounting Operations
Procedures on page 6-2.)
2
Press U or V to display 03.Delete
code.
Job Accounting:
03.Delete code
6-3
Job Accounting
3
Press [OK].
4
Input the Department ID Code to be deleted using the numeric keys.
NOTE: If a mistake is made during input it can be cleared by pressing
[Stop/Clear] and the value reentered.
5
Confirm the code to be deleted and then press [OK].
6
Press U or V and select Yes. To cancel deletion, select No.
7
Press [OK]. The display will return to that of Step 2.
Clearing the Job Accounting Count
The Total No. of Copies Count for all departments can be cleared.
1
Display the Job Accounting. (Refer to Job Accounting Operations
Procedures on page 6-2.)
2
Press U or V to display 04.Count
Clear.
3
Press [OK].
4
Press U and select Yes. To cancel the clearing of the count, select No.
5
Press [OK]. The counter will be cleared and the display will return to that
of Step 2.
Job Accounting:
04.Count Clear
Outputting the Job Accounting List
The Total No. of Copies by department can be output.
1
Display the Job Accounting. (Refer to Job Accounting Operations
Procedures on page 6-2.)
2
Press U or V to display 05.Print list.
Job Accounting:
05.Print list
NOTE: Check to make sure that Letter/A4 size paper is loaded in the
cassette.
3
6-4
Press [OK]. The list will be output and the display will return to that of Step
2.
OPERATION GUIDE
Job Accounting
Sample: Department
Management List
How to set the Job Accounting
Set Job Accounting to enable or disable it.
OPERATION GUIDE
1
Display the Job Accounting. (Refer to Job Accounting Operations
Procedures on page 6-2.)
2
Press U or V to display
01.JobAccounting.
3
Press [OK].
4
Press U or V and select On when Job Accounting is to be used and Off
when it will not be used.
5
Press [OK]. The display will return to that of Step 2.
Job Accounting:
01.JobAccounting
6-5
Job Accounting
Making copies in the Job Accounting
When Job Accounting is being carried out “= = =” will be displayed in the
No. of Copies display and copy operations can be carried out by entering
the assigned Department ID Codes using the numeric keys.
IMPORTANT: Always remember to press [Job Accounting] after
completing copying.
1
Confirm the ID code to be deleted and then press [OK]. “1” will be
displayed on the No. of Copies display.
NOTE: When an error has been made in input, press [Stop/Clear] and
input the data again.
When the Department ID Code that is input does not match any of the
Department ID Codes registered, Illegal Account. is displayed and
the copier returns to the “= = =” display. Input the correct Department ID
Code.
6-6
2
Carry out regular copy operations.
3
Press [Job Accounting] after completing copying. “= = =” will be
displayed on the No. of Copies display.
OPERATION GUIDE
Optional Equipment
7 Optional Equipment
This chapter introduces optional equipment available for the
copier.
Duplex Unit
Document Processor
Additional Memory
Printer Kit
Paper Feeder
OPERATION GUIDE
Key Counter
Print server
7-1
Optional Equipment
Document Processor
The Document Processor automatically feeds one-sided originals one by
one for scanning. It also reverses two-sided originals automatically for
duplex copying and split copying.
Originals that can be used with the Document Processor
•
•
•
•
Sheet originals only.
Single-sided originals that have a paper weight within the range of
45 g/m2 to 160 g/m2.
Two-sided originals that have a paper weight within the range of
50 g/m2 to 120 g/m2.
Sizes: Ledger to Statement, Oficio 2, A3 to A5R, Folio
No. of Sheets that can be loaded:
50 sheets (50 to 80 g/m2)
(Note, however, that when in Mixed Size Mode, this number is
reduced to 30 sheets.)
Notes on acceptable documents
Be sure NOT to use the following as originals in the Document Processor.
In addition, originals with punched holes or perforations should be set so
that the edge of the paper with the holes or perforations is facing away from
the direction of insertion into the Document Processor.
•
•
•
•
•
•
•
•
7-2
OHP film or other transparencies.
Soft originals such as carbon or vinyl paper, or other originals that
are curled, wrinkled or creased.
Irregularly shaped originals, wet originals, or originals that have
adhesive tape or glue on them.
Originals bound with clips or staples. (If you must use such originals,
be sure to remove the clips or staples, and straighten any curls,
wrinkles or creases, before setting them in the Document Processor.
Failure to do so may result in the originals being misfed.)
Originals with cut-out sections or that have a slippery surface on
either side.
Originals on which any correction fluid is still wet.
Originals with strong folds. (If you must use such originals, be sure to
smooth out the folds before setting them in the Document Processor.
Failure to do so may result in the originals being misfed.)
Originals with sharp curves (when use of a curved original is
unavoidable, straighten out the curves before setting it).
OPERATION GUIDE
Optional Equipment
Section Names
1
Left Cover
2
Original Width Guides
3
Original Table
4
Original Eject Table
1
2
3
2
4
5
Originals that have been
copied are stored here.
5
Ejection Extension
6
Ejection Tray
The original will be
temporarily ejected when
copies of both sides are
made.
7
6
7
Document Processor Open/Close Handle
Setting Originals in the Document Processor
1
Adjust the original width guides to
match the size of the original.
NOTE: Check to make sure that
there are no ejected originals
remaining on the Original Eject
Table before setting the original.
Originals left on the Original Eject
Table may cause the original to
jam.
When setting multiple originals at the same time, make sure that they are
all of the same size. Note, however, that when setting originals in the
Mixed Original Sizes Mode, originals with the same width, such as Ledger
to Letter R, A3 or A4, can be set at the same time. (Refer to Mixed
Original Sizes Mode on page 7-5.)
OPERATION GUIDE
7-3
Optional Equipment
2
Place the originals to be copied
with the side to be copied facing
up (in the case of 2-Sided copies,
place them with the Front side
facing up) and place them in order
on the Originals Table.
IMPORTANT: Set the originals
below the scale gradation pasted
on the rear original width guide.
Setting more than the acceptable
number of originals may lead to
the originals jamming. (Refer to
Originals that can be used with
the Document Processor on page
7-2 for the number of originals that
can be set.)
When setting Ledger, Legal, A3 or
B4 originals open the Ejection
Extension to prevent the originals
from falling after ejection.
In the case of Front and Back
originals, the originals will be turned over so the originals will be
temporarily ejected into the Ejection Tray. Do not handle the originals
during this temporary ejection. Trying to pull an original out by force may
cause a paper misfeed.
Setting the Original on the Platen
When copying items such as books or magazines that cannot be set in the
Document Processor, open the Document Processor and place the
original on the platen.
1
7-4
Open the Document Processor by
grasping the Document
Processor Open/Close handle.
OPERATION GUIDE
Optional Equipment
NOTE: Check to make sure that there are no originals remaining on the
Original Table or on the Original Eject Table before opening the Document
Processor. Originals left there may fall out when the Document Processor
is opened.
2
Place the side to be copied so that
it faces down. At this time, adjust
the Original Size Indicator Plate to
match the size of the original.
3
Shut the Document Processor by grasping the Document Processor Open/
Close handle.
IMPORTANT: Do not use excessive force to press the Document
Processor onto the platen. The platen glass may break if excessive force
is used.
CAUTION: Do not leave the copier with the Document Processor
open. Doing so may lead to injuries.
Mixed Original Sizes Mode
When the original size has not
been specified using [Mixed
Original Size] while using the
Document Processor, the original
sizes are detected one by one and
each original is automatically
copied to a sheet of the same
size.
IMPORTANT: The maximum
number of sheets that can be set
in the Document Processor in this
mode is 30 sheets.
[Inch specifications]
11" 17"
(A3)
8 1/2" 14"
(Folio)
11" 8 1/2"
(A4)
8 1/2" 11"
(A4R)
Only Letter R and Ledger, or
Legal and Letter sizes.
[Metric specifications]
B4
B5
Only A4 and A3, B5 and B4, or
A4R and Folio sizes.
OPERATION GUIDE
7-5
Optional Equipment
1
Set the originals in the Document Processor.
2
Press [Mixed Original Size]. The Mixed Original Sizes Indicator will light
up.
3
Press [Start]. The copier will begin copying.
Paper Feeder
In addition to the cassettes
provided with the copier, a Paper
Feeder (a 3-level device with a
cassette that can hold 300
sheets) can also be used.
•
•
The number of sheets that
can be accommodated: 300
sheets (standard paper, 64
to 105 g/m2).
Sizes that can be set are:
Ledger to Statement, Oficio 2, A3, B4, A4, A4R, B5, B5R, A5R and
Folio.
The cassette is set in the same way as the standard cassette provided with
the main unit. Refer to Loading Paper on page 2-2.
* The Left Cover has been provided to allow for the extraction of sheets
when jamming occurs.
Duplex Unit
2-Sided copies can be made
when the Duplex Unit is installed.
2-Sided copies of sizes from
Ledger to Statement, Oficio 2, A3
to A5R, Folio (64 to 90 g/m2) can
be made.
Key Counter
The Key Counter is used to
confirm the amount of usage of
the copier. It is useful in managing
copier usage for each
department, section, etc. as well
as in the company overall.
7-6
OPERATION GUIDE
Optional Equipment
Setting the Key Counter
Set the Key Counter securely in
the Key Counter Slot.
NOTE: In the case where the Key Counter is used, no one will be able to
make copies until it is installed in the copier. “U1” will be displayed when
the Key Counter has not been securely inserted.
Printer Kit
Install the printer kit to use the
copier as a printer as well.
Print server
The print server provides an
optimal printing network so that all
users on the network can take
advantage of them. The print
server's USB interface offers easy
external connections. Our original
utility simplifies configuring your
Ethernet network to offer printing
to users.
OPERATION GUIDE
7-7
Optional Equipment
Additional Memory
Memory can be increased.
Increasing the amount of memory
will increase the maximum
number of originals that can be
read in. 64MB and128MB are
effective in reading in photo
originals at low compression
ratios.
(16MB, 32MB, 64MB, 128MB)
16MB: 250 sheets, 32MB: 250 sheets, 64MB: 250 sheets, 128MB:
250 sheets (Letter blackness ratio 6% originals)
7-8
OPERATION GUIDE
Maintenance
8 Maintenance
This chapter describes cleaning and toner replacement.
•
•
OPERATION GUIDE
Cleaning the Copier...................................................... 8-2
Replacing the Toner Container and Waste Toner Box.. 8-5
8-1
Maintenance
Cleaning the Copier
CAUTION: Remove the power plug from the outlet during cleaning
operations as a safety precaution.
Cleaning the Original Cover
Open the Original Cover and use
a cloth dampened with alcohol or
a dilute neutral detergent to clean
the underside of the Original
Cover.
IMPORTANT: Do not use thinner, organic solvents etc.
Cleaning the Platen
Open the Original Cover and use
a cloth dampened with alcohol or
a dilute neutral detergent to clean
the Platen.
IMPORTANT: Do not use thinner, organic solvents etc.
Cleaning the Slit Glass
When black streaks appear on
copies when using the optional
Document Processor, this means
that the Slit Glass (a) is dirty. Use
a soft dry cloth to clean the slit
glass.
(a)
IMPORTANT: Do not use water, thinner, organic solvents, alcohol, etc.
* Refer to Replacing the Toner Container and Waste Toner Box on page
8-5 for instructions for cleaning the inside of the copier.
8-2
OPERATION GUIDE
Maintenance
Cleaning the Separation Pawl
1
Open the front cover.
2
Remove the cleaning brush.
3
Grasp the Left Cover handles to
lift the cover and open it.
4
Brush from the left side to the right
side along the separation pawl as
shown in the illustration to remove
any dirt or dust.
Separation
Pawl
5
OPERATION GUIDE
Close the left cover.
8-3
Maintenance
Cleaning the Transfer Rollers
8-4
1
Open the front cover.
2
Remove the cleaning brush.
3
Grasp the Left Cover handles to
lift the cover and open it.
4
Turn the Left Transport Roller
gear as shown in the illustration
and move the brush from left to
right while turning the gear to
remove any dust or dirt on the
rollers.
5
Close the left cover.
OPERATION GUIDE
Maintenance
Replacing the Toner Container and Waste Toner Box
When the Add Toner Indicator on the Operation Panel lights up and the
copier stops, replace the Toner. Replace the Waste Toner Box at the same
time you replace the Toner Container.
•
•
Replenish the Toner only when the Add Toner Indicator lights up or
blinks.
Whenever the Toner Container is changed, always carry out the
procedures listed from Step 7 on page8-7 through Step 11 on page88. If any section is left dirty, the performance of the product cannot be
maintained.
CAUTION: Do not attempt to incinerate the toner cartridge or waste
toner box. Doing so will generate sparks and may lead to burns.
Do not try to force open or crush the toner container or waste toner
box.
1
Open the front cover.
2
Push the Waste Toner Box holder
to the left and remove the Waste
Toner Box while pushing the
holder.
IMPORTANT: Do not invert the old Waste Toner Box.
WARNING: The electrically charged section inside the main unit
of the copier uses high voltage. Exercise caution in handling it to
prevent electric shock.
OPERATION GUIDE
8-5
Maintenance
3
Use the cap attached to the center
of the old Waste Toner Box to
cover the opening.
4
Turn Toner Container release
lever (1) to the left and remove the
Toner Container.
(1)
CAUTION: Do not attempt to incinerate the toner cartridge or waste
toner box. Doing so will generate sparks and may lead to burns.
Do not try to force open or crush the toner container or waste toner
box.
8-6
5
Place the old Waste Toner Box in
the plastic bag provided for
disposal.
6
Place the old Toner Container in
the plastic bag provided for
disposal.
OPERATION GUIDE
Maintenance
7
Grasp the Cleaning Rod and pull
gently pull it out as far as it will go
and then push it in again.
Repeat this operation several
times.
NOTE: Do not use excessive force to pull the rod or attempt to pull it out.
OPERATION GUIDE
8
While pushing the electrical
charge section to the right, pull it
out approximately 5 cm (2
inches).
9
Remove the accompanying Grid
Cleaner from its package and
remove its cap.
10
Match the Grid Cleaner to the
notch and install it in the copier
main unit.
11
While holding gently the Grid
Cleaner with your left hand, pull
out the Electrical Charge Section
as far as it will go and push it back
until the portion (2) does not touch
the white pad of the Grid Cleaner.
Repeat this operation several
times.
(2)
8-7
Maintenance
NOTE: When pushing back the Electrical Charge Section, do not push it
all the way into the main body. Copying trouble may occur.
After cleaning the Electrical Charge Section using the Grid Cleaner, wait
more than 5 minutes before using the machine.
12
When the Electrical Charge
Section is pulled out
approximately 5 cm (2 inches),
remove the Grid Cleaner and then
push back the Electrical Charge
Section all the way into the main
body.
13
Hold the new toner container
vertically and tap the upper part
five times or more.
Turn the toner container upside
down and tap the upper part five
times or more.
14
Shake the toner container up and
down five times or more.
Turn the toner container upside
down and shake it five times or
more.
15
8-8
5
5
Hold the toner container
horizontally and shake it from side
to side five times or more.
OPERATION GUIDE
Maintenance
16
Set the new Toner Container in
place, and turn Toner Container
Release Lever (1) to the right.
17
Install the new Waste Toner Box.
18
Close the front cover.
(1)
Return used toner containers and waste toner boxes to the dealer you
purchased them from or to a sales representative. Recovered toner
containers and waste toner boxes will be either reused, recycled or
disposed of in accordance with the law.
NOTE: In order to ensure maximum copier performance, in addition to
the cleaning done when changing the Toner Container, regularly (about 1
time per month) carry out Step 7 described in page8-7 and Step 10
described in page8-7.
OPERATION GUIDE
8-9
Maintenance
8-10
OPERATION GUIDE
Troubleshooting
9 Troubleshooting
This chapter explains how to solve problems with the copier.
•
•
•
OPERATION GUIDE
If other trouble occurs................................................... 9-2
If one of the following indications is Displayed ............. 9-5
If paper jams................................................................. 9-9
9-1
Troubleshooting
If other trouble occurs
Check the following items when trouble occurs. If the problem is not
resolved after checking these items, contact your service representative.
Items to Check
Nothing displays on
the Operation Panel
even though the
Power Switch is ON.
Check to make sure the copier is
plugged into the outlet.
Plug the copier power cord into
the outlet.
–
No copy is produced
when [Start] is
pressed.
Check to see if something has
been displayed on the Operation
Panel.
Check the corrective procedure
for the error display and carry it
out.
9-5
Nothing appears on
the copy.
Check to see that the original
has been set properly.
Place the original face down on
the platen and adjust the Original
Size Indicator Plate to match its
size.
Place the original face up when
setting it in the optional
Document Processor.
3-2
Check to see if the copier is in
Auto Exposure Mode.
When the exposure is to be
changed overall, perform out the
“Auto Exposure Adjustment”.
5-11
Check to see if the copier is in
Manual Exposure Mode.
Use Exposure Adjustment to set
the proper exposure.
3-3
When the exposure is to be
changed overall, perform the
Manual Exposure Adjustment in
each original mode.
3-3
Check to see if the toner in the
toner container is canted.
Shake the Toner Container left
and right for approximately 10
times.
8-8
Check to see if the Add Toner
Indicator is lit.
Replace the Toner Container.
8-5
Check to see if the paper is
damp or not.
Replace the paper with new
paper.
–
Check to see if the electrical
charge section is dirty or not.
Open the front cover and use the
Cleaning Rod to clean the
electrical charge section.
8-7
A light copy is
produced.
9-2
Corrective Procedure
Reference
Page
Symptom
7-3
OPERATION GUIDE
Troubleshooting
Symptom
Dark copies are
produced.
Items to Check
Corrective Procedure
Reference
Page
Check to see if the copier is in
Auto Exposure Mode.
When the exposure is to be
changed overall, perform out the
“Auto Exposure Adjustment”.
5-11
Check to see if the copier is in
Manual Exposure Mode.
Use Exposure Adjustment to set
the proper exposure.
3-3
When the exposure is to be
changed overall, perform the
Manual Exposure Adjustment in
each original mode.
3-3
Spotting (the
shading fails to line
up uniformly and
spots occur).
Check to see whether the
original is a printed original or
not.
Select “Photos” in the Image
Quality Mode.
3-3
The copy is not
clear.
Check to see whether an Image
Quality Mode that matches the
type of original being copied has
been selected or not.
Select the appropriate Image
Quality Mode.
3-3
The copy is dirty.
Check to see if the Platen or
Original Cover is dirty.
Clean the Platen and Original
Cover.
8-2
The copy image is
skewed.
Check to see that the original
has been set properly.
Make sure that the original is
correctly set against the Original
Size Indicator Plate when
placing the original on the platen.
When setting the original in the
optional Document Processor
make sure that the original is
correctly aligned with the original
insertion guide.
3-2
Check the position of the Width
Guide in the cassette.
2-2
Check to see that the paper has
been set properly.
OPERATION GUIDE
7-3
9-3
Troubleshooting
Symptom
Paper misfeeds
occur frequently
Items to Check
Corrective Procedure
Reference
Page
Check to see that the paper has
been loaded properly in the
cassette.
Set the paper correctly.
2-2
Depending on the type of paper
and its storage condition, there
may be cases in which the
copies curl. This may lead to
paper misfeeds. Remove the
paper, turn it over and then
replace it.
–
Check to see if the paper is
curled, creased or wrinkled.
Replace the paper with new
paper.
–
Check to see if fragments of
paper or a jammed sheet is in
the copier.
Use an appropriate method to
remove the fragment or jammed
sheet of paper.
9-9
Check to see if the paper size
actually set in the MP Tray and
the MP Tray Size set are
different or not.
Match the paper size of the
paper set in the MP Tray and the
MP Tray Size setting.
–
Black streaks appear
on the copy when
the optional
Document Processor
is used.
Check to see if the slit glass is
dirty.
Clean the slit glass if it is dirty.
In addition, you can set the
Processing to Reduce Black
Streaks when black streaking
occurs to make the streaking
unnoticable.
8-2
5-12
Wrinkling occurs in
copies.
Check to see if the separation
pawl is dirty.
Clean the separation pawl if it is
dirty.
8-3
A white or black
lengthwise line
shows up on copies.
Check to see if the electrical
charge section is dirty or not.
Open the front cover and use a
cleaning rod to clean it.
8-7
White spots appear
on copies.
Check to see if the transfer
rollers are dirty.
Scrub the transfer rollers with a
cleaning brush to clean them.
8-4
9-4
OPERATION GUIDE
Troubleshooting
If one of the following indications is Displayed
Carry out the corresponding corrective procedure when any of the error
messages shown in the table below are displayed.
Display
Add paper
in cassette #.
Add toner.
Cannot copy
this paper size.
Corrective Procedure
Reference
Page
There is no paper in the cassette. Load paper into the
cassette as displayed in place of #.
2-2
Copies cannot be produced because there is no toner.
Replace the toner container with a new one.
8-5
An original size that cannot be copied has been set.
Check the original.
• The original was set in a vertical direction during the
Book Border Erasure copying operation. Set the
original horizontally.
• An irregular size original was set during the Border
Erase or Combine mode operation.
• An original size other than Letter, Ledger, A3, A4R,
A5R, B4 or B5R was set to make a split copy or a 2Sided Copy from a double-page spread original.
4-10
4-10, 4-12
4-6
Cannot duplex
this paper size
A size that cannot be copied on both sides has been
specified. 2-Sided copies cannot be taken when A6R,
B6R, Postcard, Irregular Size or the paper size has not
been specified. Specify a paper size that can be used.
4-2
Call service.
C####
Make a note of the C and the number (C# # # #). Turn
the power switch OFF, unplug the power cord and
contact your service representative.
–
The Document Processor is open. Close the Document
Processor.
–
The left cover of the Document Processor is open. Close
the left cover. Close the front cover.
–
The front cover of the copier is open. Close the front
cover.
–
Close document
processor.
Close document
processor cover.
Close
front cover.
OPERATION GUIDE
9-5
Troubleshooting
Display
Close
left cover #.
The left cover of the cassette is open. Close the left
cover as displayed in place of #.
Check the key counter and make sure it is set properly.
7-7
No Letter/A4 size paper was available in either the
cassette or the Paper Feeder (MP tray) at the time when
the report was attempted to be output. Press [Paper
Selection] and select the supply cassette, then press
[Start]. Paper will be supplied from the cassette
selected.
–
Turn the power switch OFF/ON. Usage will be possible
again once the regular display returns. When A and the
number (A# # # #) are again displayed, make a note of
the A and the number. Turn the power switch OFF,
unplug the power cord and contact your service
representative.
–
Copies cannot be produced because memory is full
during the interrupt copy operation. Interrupt Copying
cannot be carried out so press [Stop/Clear] and then
press [Interrupt] again after the data read in has been
deleted to exit the Interrupt Copying.
After the copying operation for the interrupted copy has
been completed, repeat the procedure again.
–
Memory is full.
Press [OK] to start outputting the copies read in. Press
[Reset] or [Stop/Clear] to delete the data read in.
Reduce the number of originals and repeat the copying
procedure.
–
MP tray empty.
Add paper.
Check the MP Tray paper. Set paper in the MP Tray in
the event there is no paper present there. When the MP
Tray paper fails to be fed, reset the paper.
2-6
Paper jam
A paper misfeed has occurred. Remove the jammed
paper.
9-9
Place the
original on DP.
The copier will try to make copies of the originals it could
not copy before. Return all of the originals to the original
table and try copying them again.
–
Insert
key counter.
No matching
paper available.
MainPower Off/On
A####
Memory is full.
Cannot continue.
Memory is full.
Press OK.
9-6
Reference
Page
Corrective Procedure
OPERATION GUIDE
Troubleshooting
Display
Corrective Procedure
Reference
Page
The waste toner box is full. Replace it with a new waste
toner box.
8-5
250 copies have been stored on output tray. Remove
the paper, press [Start] and resume copying.
–
Originals were set in the optional Document Processor
when copying on 2-sides (front and back sides), when
copying from the platen in 2-Sided copy, 2 in 1, 4 in 1 or
when collating copies. Remove the originals from the
Document Processor, replace the originals on the
Original Table after exiting the front and back copying, 2Sided copy, 2 in 1, 4 in 1 or Collate Mode and resume
copying.
–
If the optional Document Processor is being used, there
are originals left on the original table. Remove the
originals, return them to the original table and try
copying them again.
–
Check the paper cassette that corresponds to the
lighting indicator. Set the cassette.
2-2
The Toner Container has not been set. Set the Toner
Container.
8-5
The Add Toner indicator blinks on
and off.
There is very little toner remaining. Copying can be
continued for a short while before running out of toner.
Replace the toner container with a new one as soon as
possible.
8-5
The Periodic Maintenance
indicator blinks on and off.
This is a notification that the time for periodic
maintenance is approaching.
–
The Periodic Maintenance
indicator lights up.
It is time for Periodic Maintenance. Contact your service
representative.
–
“= = =” appears on the copy
quantity display.
Job Accounting being set. Use the numeric keys to enter
the assigned Section Code to perform copying
operations. Press [Job Accounting] after copying is
finished to display “= = =” again.
6-6
“-” appears on the copy quantity
display.
The copier is in the Sleep Mode setting. Press [Energy
saver] to exit the mode.
3-9
Replace waste
toner box.
Remove paper on
top tray; Start.
Reseat originals
on DP.
Return all
originals to DP.
Set paper
cassette.
Set toner
container.
OPERATION GUIDE
9-7
Troubleshooting
Reference
Page
Display
Corrective Procedure
“---” appears on the copy quantity
display.
The copier is in the Low Power mode setting. Press any
key to exit the mode or in the case where the optional
Document Processor is installed, set an original in the
Document Processor.
9-8
3-8
OPERATION GUIDE
Troubleshooting
If paper jams
Stop copying operations when a paper misfeed occurs. When a paper
misfeed occurs, the indicator for the location of the paper misfeed will light
up on the Operation Panel and either “J” plus a 2-digit number will be
displayed as notification of the location of the paper misfeed.
With the Power Switch in the ON (|) position, refer to Removal
Procedure on page 9-9 and clear the paper misfeed.
Misfeed location indicators
1
2
Paper misfeed in the paper
supply section – Refer to
page9-9.
Paper misfeed in the left
cover internal section –
Refer to page9-11.
3
2
1
3
Paper misfeed in the
optional Document
Processor – Refer to
page9-12.
4
Paper misfeed in the optional cassette – Refer to page9-13.
4
WARNING: The electrically charged section inside the main unit
of the copier uses high voltage. Exercise caution in handling it to
prevent electric shock.
CAUTION: The fixation section inside the main unit of the copier is
extremely hot. Exercise caution in handling it to prevent getting
burned.
*Do not attempt to reuse paper that has jammed before.
*When a sheet gets torn during removal, make sure that the remnants do
not remain in the machine. Failure to completely remove remnants of torn
pages can lead to paper misfeeds.
*The copier will start warm up operations after the paper misfeed
processing has been completed. The paper misfeed indicator lamp will
go off and the copier will be restored to the state it was in before the paper
misfeed occurred.
Removal Procedure
Paper misfeed in the paper supply section
Paper misfeed in the cassette (J11, J21)
When the paper misfeed has occurred in the cassette, use the procedure
below to clear it.
OPERATION GUIDE
9-9
Troubleshooting
1
Pull the cassette out.
2
If a sheet of paper is jammed
inside, remove it carefully so as
not to tear it.
NOTE: If the paper is torn, be sure to remove all remnants or fragments
from the cassette.
3
Firmly push the cassette back into its original position.
NOTE: Check to see that there is no paper sticking out from the guides in
the cassette. If paper is sticking out, recheck the cassette.
In the case where “J21” is displayed, refer to Paper misfeed in the Left
Cover internal section (J20, J30, J40 to 45, J50, J52 to 56, J60, J61) on
page 9-11 and remove the paper.
Paper misfeed in the MP Tray (J10)
When the paper misfeed has occurred in the MP Tray, use the procedure
below to clear it.
1
9-10
Remove all of the MP Tray paper.
OPERATION GUIDE
Troubleshooting
2
Check to see that the paper
misfeed indicator lamp has gone
out and then set the MP Tray
paper again.
IMPORTANT: Paper misfeed in the MP Tray (except J10)
In the case where “J20" is displayed, refer to Paper misfeed in the Left
Cover internal section and remove the paper.
In the case where “J40" is displayed, refer to Paper misfeed in the Left
Cover internal section and remove the paper.
When removing jammed paper, do not pull it out from the MP tray side.
Paper misfeed in the Left Cover internal section (J20, J30, J40 to 45, J50,
J52 to 56, J60, J61)
When the paper misfeed has occurred in the Left Cover internal section,
use the procedure below to clear it.
NOTE: Supplementary Information
The drum section inside the main unit is sensitive to scratches and
contaminants. When removing paper, be careful not to touch it or scratch
it with your watch, ring, etc.
1
Grasp the Left Cover handles to
lift the cover and open it.
CAUTION: The fixation section inside the main unit of the copier is
extremely hot. Exercise caution in handling it to prevent getting burned.
2
OPERATION GUIDE
Remove jammed sheets of paper
carefully so as not to tear them.
9-11
Troubleshooting
NOTE: If the paper is torn, be sure to remove all remnants or fragments
from the cassette.
3
If the Duplex Unit (option) is
installed, lift it up and remove the
paper.
NOTE: If the paper is torn, be sure to remove all remnants or fragments
from the cassette.
4
Close the left cover.
Paper misfeed in the Document Processor (option) (J70 to 75)
When the paper misfeed has occurred in the optional Document
Processor, use the procedure below to clear it.
9-12
1
If there are originals on the
Original Table, remove them.
2
Open the Left Cover.
OPERATION GUIDE
Troubleshooting
3
If an original is jammed inside,
remove it carefully so as not to
tear it.
NOTE: If the original is torn, be sure to remove all remnants or fragments
of it from the cassette. Failure to completely remove remnants of torn
pages can lead to paper misfeeds.
4
Lift up the Paper Supply Unit (1).
5
If an original is jammed inside, remove it carefully so as not to tear it.
(1)
NOTE: If the original is torn, be sure to remove all remnants or fragments
of it from the cassette.
6
Rotate the dial as shown in the
illustration and remove the
original.
7
Close the Left Cover to return it to its original position.
Add the original that was jammed to the originals on the Original Table and
resume copying.
Paper misfeed in the optional cassette (J12 to 16, J22 to 24)
When the paper misfeed has occurred in the optional cassette, use the
procedure below to clear it.
OPERATION GUIDE
9-13
Troubleshooting
1
Remove the left cover of the
cassette being used.
2
If a sheet of paper is jammed
inside, remove it carefully so as
not to tear it.
NOTE: If the paper is torn, be sure to remove all remnants or fragments
from the cassette.
9-14
3
Close the left cover of the
cassette.
4
Pull the cassette out.
OPERATION GUIDE
Troubleshooting
5
If a sheet of paper is jammed
inside, remove it carefully so as
not to tear it.
NOTE: If the paper is torn, be sure to remove all remnants or fragments
from the cassette.
6
OPERATION GUIDE
Gently push the cassette back into its original position.
9-15
Troubleshooting
9-16
OPERATION GUIDE
Appendix
This appendix lists the copier specifications.
Specifications
NOTE: Specifications are subject to change without notice.
Main Body
Item
Description
Type
Desktop Type
Original Table
Fixed Original Table
Copy System
Indirect electrostatic system
Original Types
Accommodated
Sheets, books and 3-dimensional objects (Maximum original size: Ledger/A3)
Copy Sizes
Ledger, Legal, Letter, Letter R, Statement, Oficio 2, A3, B4, A4, A4R, B5, B5R,
A5R, B6R, A6R, Postcard, Folio, 8k, 16k and 16k R
Width that cannot be copied: 0.5 to 5.5 mm
Copying Speed
- 16-sheet copier
1:1/Memory Copy Ledger/A3:8 sheets/minute, Legal/B4:8 sheets/minute,
Letter/A4:16 sheets/minute, Letter R/A4R:13 sheets/minute, B5:16 sheets/
minute, B5R:13 sheets/minute, A5R:10 sheets/minute, A6R:10 sheets/minute
- 20-sheet copier
1:1/Memory Copy Ledger/A3:10 sheets/minute, Legal/B4:10 sheets/minute,
Letter/A4:20 sheets/minute, Letter R/A4R:13 sheets/minute, B5:20 sheets/
minute, B5R:13 sheets/minute, A5R:10 sheets/minute, A6R:10 sheets/minute
Warm-up Time
Less than 20 seconds (Room Temperature 71.6ºF/22ºC, Humidity 60% RH)
First Copy Time
Less than 5.9 seconds (A4)
Copying Magnification
25 to 400% (1% increments) with variable and fixed magnifications. (25 to
200% with the document processor)
Standard Memory
18MB bitmap memory. 14MB image storage memory.
Resolution
Reading: 600 × 600 dpi
Writing: 600 × 600 dpi
Paper Supply System
Automatic Cassette Feed (Sheet storage: 300 sheets [80 g/m2]) and MP Tray
(Sheet storage: 50 sheets [80 g/m2])
OPERATION GUIDE
Appendix-1
Item
Acceptable Paper
- Paper Weights
Description
Cassette: 64 to 105 g/m2
Duplex Unit: 64 to 90 g/m2
MP Tray: 45 to 160 g/m2
- Media Types
Cassette: Standard paper, recycled paper and color paper
Duplex Unit: Standard paper, recycled paper and color paper
MP Tray: Standard paper, recycled paper, color paper, vellum paper and thick
paper
Consecutive Copying
1 to 999 sheets
Light Source
Rare gas lamp
Developing System
Dry developing
Fixation System
Heat roller
Cleaning System
Blade cleaning system
Drum Type
OPC
Standard Functions and
Modes
Automatic Paper Selection, Image Quality Selection, Automatic Magnification
Selection Mode, Zoom Mode, 2-Sided Copy1, Split Copy, Margin Shift, Border
Width, Combine mode, Collate Copy, EcoPrint, Copy Program and Job
Accounting
1...When the Duplex Unit (option) is installed.
Ambient conditions
- Temperature
10 to 32.5 °C
- Humidity
15 to 80 %RH
- Altitude
Maximum 2,500m
- Illumination
1,500 lux or less
Power Source
- Inch specifications
120V AC 60Hz 9.0A
- Metric specifications
220 to 240V AC 50Hz 5.0A
Dimensions
Width 22 5/8" × Depth 21 3/4" × Height 19 3/4"
Width 574 mm × Depth 552 mm × Height 502 mm
Weight
Approximately 85.9 lbs/39 kg
Required Space
Width 32 9/16" × Depth 21 3/4"
Width 827 mm × Depth 552 mm
Options
Document Processor, Paper Feeder, Duplex Unit, Key Counter
The Original Cover is standard depending on the destination.
Appendix-2
OPERATION GUIDE
Document Processor (option).
Item
Description
Original Feed System
Automatic feed system
Acceptable Types of
Originals
Sheet originals
Original Sizes
Maximum: Ledger/A3
Minimum: Statement/A5R
Original Thickness
(paper weight)
Single-side Originals: 45 to 160 g/m2
Double-sided Originals: 50 to 120 g/m2
No. of Originals that can
be loaded
Less than 50 sheets (50 to 80 g/m2)
Power Source
Electrically connected to the copier main unit
External Dimensions
Width 21 3/4" × Depth 19 1/8" × Height 4 11/16"
Width 552 mm × Depth 483 mm × Height 120 mm
Weight
Approximately 13.2 lbs/6 kg
Paper Feeder (option)
Item
Description
Paper Supply System
Automatic Cassette Feed (sheet storage 300 sheets [80 g/m2])
Paper Sizes
Ledger, Legal, Letter, Letter R, Statement, Oficio 2, A3, B4, A4, A4R, B5, B5R
and A5R
Acceptable Paper
- Paper Weights
64 to 105 g/m2
- Media Types
Standard paper, recycled paper and color paper
Power Source
Electrically connected to the copier main unit
Dimensions
Width 22 7/16" × Depth 21 3/16" × Height 5 5/16"
Width 570 mm × Depth 538 mm × Height 135 mm
Weight
Approximately 15.4 lbs/7 kg
Duplex Unit (option)
Item
Description
System
Internal type
Paper Sizes
Ledger, Legal, Letter, LetterR, Statement, Folio, Oficio 2, A3, B4, A4, A4R, B5,
B5R and A5R
OPERATION GUIDE
Appendix-3
Item
Description
Acceptable Paper
- Paper Weights
64 to 90 g/m2
- Media Types
Standard paper, recycled paper and color paper
Power Source
Electrically connected to the copier main unit
Dimensions
Width 14 1/2" × Depth 2 1/16" × Height 7 1/16"
Width 368 mm × Depth 53 mm × Height 180 mm
Weight
Approximately 1.4 lbs/0.65 kg
Additional Memory (option).
Item
Description
Memory Type
100-pin DIMM
Memory Capacity
16MB, 32MB, 64MB and 128MB
No. of Originals that can
be read in
16MB: 250 sheets, 32MB: 250 sheets, 64MB: 250 sheets, 128MB: 250 sheets
(Letter, blackness ratio 6% originals)
Environmental Specifications
Power consumption
Inch specifications
120V AC 60Hz
Item
Metric specifications
220 to 240V AC 50Hz
Recovery time from the Low Power mode
10 seconds
10 seconds
Transition time to the Low Power mode (at time
of purchase)
15 minutes
15 minutes
Transition time to the Sleep modes (at time of
purchase)
30 minutes
30 minutes
Power consumption in the Plugged-In mode can only be terminated by
removing the power plug from the outlet.
2-Sided Copy Function
Option
Paper Transportability
Recycled paper made from 100% recycled pulp may be used with this product.
Please consult with dealer or sales representative for information on the
recommended types of paper, etc.
Appendix-4
OPERATION GUIDE
Functions and Settings Combination Chart
This copier has various functions, which if used together, can further
increase copying efficiency. Refer to the chart below for function
combinations.
The blank space can be combined as desired.
-= Cannot be combined.
DP: Document Processor
Secondary Priority
01= Clears the prior setting and gives priority to the later setting.
02= Switches the copier to Manual Exposure because the Photo Mode
does not have Auto Exposure.
03= Mixed Original Sizes automatically detects the original size and
switches the copier to Automatic Paper Selection Mode.
04= Switches the copier to automatic magnification when Combine mode
is set.
05= This type of media cannot be copied on both sides. The media type
will be given priority and 2-Sided Copy exited.
06= Automatic Paper Selection is cleared and the copier switched to
automatic magnification or manual mode.
07= When a supply level other than A4, B5, Letter or 16k is to be selected,
select the A4, B5, Letter or 16k paper size supply level.
Primary Priority
21= Setting is not possible because the Photo Mode does not have Auto
Exposure.
22= Mixed Original Sizes has only Original Size Automatic Detection and
Automatic Paper Selection.
23= Single side → 2-Sided Copy and Mixed Original Sizes cannot be
combined.
24= Spread originals and Mixed Original Sizes cannot be combined.
25= Border Erase and Mixed Original Sizes cannot be combined.
26= Combine mode and Mixed Original Sizes cannot be combined.
27= Spread originals and Combine mode cannot be combined.
28= Only automatic magnification is available for Combine mode.
29= Media Type and 2-Sided Copy cannot be combined.
30= Media Type and Mixed Original Sizes cannot be combined.
31= Media Type and Automatic Paper Selection cannot be combined.
Functions can be combined (conditions for combining exist)
41= Irregular original sizes cannot be copied.
42= Vertically oriented originals and irregular original sizes cannot be
copied.
43= Sizes other than Letter, Ledger, A3R, A4R, A5R, B4R, B5R and 8k
cannot be copied.
44= 2-Sided Copies for paper sizes A6R, B6R, Postcard, Irregular Size or
unspecified MP Tray sizes where the paper size is irregular cannot be
produced.
45= Selection is not possible when the paper size is other than A4, B5,
Letter or 16k.
OPERATION GUIDE
Appendix-5
Necessary
Option
After Setting
1
2
1 2 3 1 2
1 Image
Quality
1 Text & Photo
4
5
1 2
6
7
8
1 2 1 2 3
9
:
A
1 2 3 1 2
B
C
D
E
1 2 1 2 1 2
01 -
2 Photo
-
3 Text
2 Exposure
3
01 21
01 -
1 Auto
02
2 Select
01
01
3 EcoPrint
4 Original
Size*
1 Auto
2 Select
5 Mixed Original Size
6U
Present Setting
V
7 Paper
Select
03
DP
22
22 22
1 Auto
03
2 Select
03 01
1 Auto
22 22
23
43
43
42
43
43
41 42 41 41
24
24
25 25 26 26 30 30
01 01
01
01
04 04
06 06
2 Cassette
03
01
3 MP Tray
03
01 -
-
04 04 06 06
44 44 07
07
44 44 07
07
8 Collate Copy
9 2-Sided
Copy
: Split Copy
1 1-Sided → 2-Sided
2-Sided
2 2-Sided → 2-Sided
2-Sided, DP
3 Book → 2-Sided
2-Sided
1 2-Sided → 1-Sided
DP
2 Book → 1-Sided
23
44 44
43 43 24
01 01 01 01
05 05
01 01 01
05 05
01 01
27 27 05 05
44 44
01
45 45
01 01
01 01 01
43 43 24
45 45
01
01 01 01 01
27 27
A Binding Margin
B Border
Erase
C Combine
mode
1 Sheet Border Erasure
2 Book Border Erasure
41 25
01
42 42 25
01
1 2 in 1
41 26
28 28
27
27
2 4 in 1
41 26
28 28
27
27
30
31
29 29 29
30
31
29 29 29
D Media Type 1 Thick Paper
2 Vellum Paper
01
01
01
01
E Interrupt Copying
* Note: Manual Size Selection includes Custom Sizes 1 and 2.
Appendix-6
OPERATION GUIDE
Index
Numerics
2 in 1 4-12
2-Sided copies 4-2
2-Sided Copy Reverse Side Rotation Setting
4-5
4 in 1 4-15
4 in 1 Layout Order 4-17
A
Accompanying paper sheet 2-5
Additional Memory 7-8
Adjusting Copy Exposure 3-3
Alarm 5-23
Auto Cassette Switching 5-15
Auto Clear function 1-6
Auto Clear Setting 5-20
Auto Clear Time 5-21
Auto Detect Originals 5-18
Auto Exposure Adjustment 5-11
Auto Rotation 5-20
Auto Sizing 5-15
Auto Sleep Mode 3-9
Auto Sleep Setting 5-21
Auto Zoom Ratio Selection Mode 3-5
Automatic Cassette Switching Function 1-7
Automatic Collating of copy sets 4-19
Automatic Paper Selection 5-14
Cleaning Rod 8-7
Cleaning the Copier 8-2
Cleaning the Original Cover 8-2
Cleaning the Platen 8-2
Cleaning the Separation Pawl 8-3
Cleaning the Slit Glass 8-2
Cleaning the Transfer Rollers 8-4
Collating 4-19
Completion of the Copying Procedure 3-4
Copy Limit 5-19
Copying 2 or 4 originals onto a single page
4-12
Copying Functions 4-1
Counter Report 5-24
Custom Sizes 1-7
D
Deleting Department ID Codes 6-3
Department ID Code Registration 6-3
Document Processor 7-2
Drawer Size Detection 2-5
Duplex Unit 7-6
E
EcoPrint 4-21, 5-10
Environment ix
Exposure Steps 5-10
B
F
Background Adjustment 5-13
Basic Operation 3-1
Book erase mode 4-10
Functions and Settings Combination Chart
Appendix-5
C
Cassette Selection 5-13
Cassette Size Detection 2-5
Caution Labels viii
Cautions when handling consumables xiii
Cautions when using the copier xi
OPERATION GUIDE
G
Grounding the copier x
H
Handling of plastic bags x
How to set the Job Accounting 6-5
Index-1
I
If one of the following indications is
Displayed 9-5
If other trouble occurs 9-2
If papaer jams 9-9
Image Quality Selection 3-3
Initial Density 5-9
Inputting Custom Sizes 5-15
Inputting MP Tray Size and Media Type 2-7
Interrupt Copying 3-7
J
Job Accounting 6-1
Job Accounting Operations Procedures 6-2
K
Key Counter 7-6
L
Loading Paper 2-2
Loading Paper into the Cassette 2-3
Low Power Mode 3-8
Low Power Mode Transition Time 5-22
M
Maintenance 8-1
Making a margin space on the copies 4-8
Making copies in the Job Accounting 6-6
Making copies with clean edges 4-10
Message Display 1-6
Message Language 5-8
Misfeed location indicators 9-9
Mixed Original Sizes Mode 7-5
N
Name of Parts 1-1
Notes on acceptable documents 7-2
O
Optional Equipment 7-1
Original Image Quality 5-9
Originals that can be used with the
Index-2
Document Processor 7-2
Outputting the Job Accounting List 6-4
Overview of Job Accounting 6-2
P
Paper Feeder 7-6
Paper misfeed in the cassette 9-9
Paper misfeed in the Document Processor
(option) 9-12
Paper misfeed in the Left Cover internal
section 9-11
Paper misfeed in the MP tray 9-10
Paper misfeed in the optional cassette 9-13
Paper misfeed in the paper supply section
9-9
Paper Selection 3-2
Paper Weight and 2-sided Copying 5-17
Photo Exposure Adjustment 5-11
Photo Mode 3-3
Photo Processing 5-12
Power Supply x
PRECAUTIONS FOR USE xi
Print server 7-7
Printer Kit 7-7
Procedure for Changing the Default Settings
5-8
Processing to Reduce Black Line 5-12
Program Function 4-22
Pull the electrical charge section out as far
as it will go and push it in after pulling it back
and forth several times. 8-7
R
Registering a program 4-22
Rotate Collate Setting 5-19
S
Saving on toner use 4-21
Section Names (Document Processor) 7-3
Selected Cassette 5-14
Selecting Functions 3-2
Selecting Media Type 5-17
Setting Originals in the Document Processor
7-3
Setting paper on the MP tray 2-6
OPERATION GUIDE
Setting the Border Width 4-11
Setting the Combine mode Border Lines
4-17
Setting the Key Counter 7-7
Setting the Margin 4-9
Setting the Number of Copies 3-3
Setting the Original 3-2
Setting the Original on the Platen (Document
Processor) 7-4
Sheet erase mode 4-10
Silent Mode Transition Time 5-20
Sleep Mode Transition Time (Default
Settings) 5-22
Split Copy Modes 4-6
Standard Margin 4-8
Start Copying 3-4
System Menu 1-6, 5-2
System Menu Items 5-2
System Menu Operations Procedures 5-7
System Setting 5-1
5-11
Text Exposure Adjustment 5-12
Text Mode 3-3
Toner xiii
Toner Container 8-5
Toner Container release lever 8-6
Toner Coverage Report 5-23
Total Counter 5-24
Troubleshooting 9-1
T
Z
Text + Photo Mode 3-3
Text + Photo Mode Exposure Adjustment
Zoom Copying 3-5
Zoom Mode 3-5
OPERATION GUIDE
U
User Status Report 5-8
Using programmed setting to make copies
4-22
W
Warm-up 3-2
Waste Toner Box 8-5
Index-3
Index-4
OPERATION GUIDE
For best results and machine performance, we recommend that you use only our original supplies
for your products.
A1
©2005
is a trademark of Kyocera Corporation
Revision 1.0 2005.10
">