Copystar KM-3040 Operation Guide

Copystar KM-3040 Operation Guide
Printing System(Y)
Operation Guide
Function Edition
Guides Included
The following guides are included with this machine. Refer to the guide that corresponds
to your particular objective.
Operation Guide Printer Setup Edition
This guide contains instructions for assembling and installing the machine.
Operation Guide Printer Function Edition (this guide)
This guide contains explanations on printer functions as well as default settings and
troubleshooting.
iii
Trademark Information
•
PRESCRIBE and ECOSYS are registered trademarks of Kyocera Corporation. KPDL
and KIR are trademarks of Kyocera Corporation.
•
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft
Corporation. Microsoft Windows Server is a trademark of Microsoft Corporation.
•
Macintosh, AppleTalk, and TrueType is a registered trademark of Apple Computer, Inc.
•
PostScript is a registered trademark of Adobe Systems Incorporated.
•
PCL is registered trademarks of Hewlett-Packard Company.
•
Novell and NetWare are registered trademarks of Novell, Inc.
•
Ethernet is a registered trademark of Xerox Corporation.
•
PowerPC is a trademark of International Business Machines Corporation.
•
CompactFlash is a trademarks of SanDisk Corporation.
•
This product was developed using Tornado, the real-time operating system (ROTS)
general development environment from Wind River Systems, Inc.
•
The Kyocera product uses PeerlessPrintXL to provide the HP LaserJet compatible
PCL6 language emulation. PeerlessPrintXL is a trademark of Peerless Systems
Corporation, 2381 Rosecrans Ave. El Segundo, CA 90245, U.S.A.
•
This product contains UFSTTM and MicroType® from Monotype Imaging Inc.
All other company and product names contained in this Operation Guide are trademarks
or registered trademarks of their respective companies. The designations ™ and ® will not
be used in this Operation Guide.
All rights reserved. No part of this material may be reproduced or transmitted in any form
or by any means, electronic or mechanical, including photocopying, recording or by any
information storage and retrieval system, without permission in writing from the Publisher.
Legal Restriction On Copying
•
It may be prohibited to copy copyrighted material without permission of the copyright
owner.
•
It is prohibited under any circumstances to copy domestic or foreign currencies.
•
Copying other items may be prohibited.
IBM Program License Agreement
THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE
PROGRAMS (“PROGRAMS”) WHICH BELONG TO INTERNATIONAL BUSINESS
MACHINES CORPORATION (“IBM”). THIS DOCUMENT DEFINES THE TERMS AND
CONDITIONS UNDER WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM.
IF YOU DO NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS LICENSE,
THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE YOU MAY
RETURN THE DEVICE FOR A FULL REFUND. IF YOU DO NOT SO RETURN THE
DEVICE WITHIN THE 14 DAYS, THEN YOU WILL BE ASSUMED TO HAVE AGREED TO
THESE TERMS AND CONDITIONS.
The Programs are licensed not sold. IBM, or the applicable IBM country organization,
grants you a license for the Programs only in the country where you acquired the
Programs. You obtain no rights other than those granted you under this license.
iv
The term “Programs” means the original and all whole or partial copies of it, including
modified copies or portions merged into other programs. IBM retains title to the Programs.
IBM owns, or has licensed from the owner, copyrights in the Programs.
1. License
Under this license, you may use the Programs only with the device on which they are
installed and transfer possession of the Programs and the device to another party. If you
transfer the Programs, you must transfer a copy of this license and any other
documentation to the other party. Your license is then terminated. The other party agrees
to these terms and conditions by its first use of the Program.
You may not:
1) use, copy, modify, merge, or transfer copies of the Program except as provided in this
license;
2) reverse assemble or reverse compile the Program; or
3) sublicense, rent, lease, or assign the Program.
2. Limited Warranty
The Programs are provided “AS IS.”
THERE ARE NO OTHER WARRANTIES COVERING THE PROGRAMS (OR
CONDITIONS), EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion
may not apply to you.
SUPPLEMENT TO AGREEMENT FOR SOFTWARE BUNDLING AND DISTRIBUTION
FOR ALDC
3. Limitation of Remedies
IBM’s entire liability under this license is the following;
1) For any claim (including fundamental breach), in any form, related in any way to this
license, IBM’s liability will be for actual damages only and will be limited to the greater of;
a) the equivalent of U.S.$25,000 in your local currency; or
b) IBM’s then generally available license fee for the Program
This limitation will not apply to claims for bodily injury or damages to real or tangible
personal property for which IBM is legally liable. IBM will not be liable for any lost profits,
lost savings, or any incidental damages or other economic consequential damages, even
if IBM, or its authorized supplier, has been advised of the possibility of such damages. IBM
will not be liable for any damages claimed by you based on any third party claim. This
limitation of remedies also applies to any developer of Programs supplied to IBM. IBM's
and the developer's limitations of remedies are not cumulative. Such developer is an
intended beneficiary of this Section. Some jurisdictions do not allow these limitations or
exclusions, so they may not apply to you.
v
4. General
You may terminate your license at any time. IBM may terminate your license if you fail to
comply with the terms and conditions of this license. In either event, you must destroy all
your copies of the Program. You are responsible for payment of any taxes, including
personal property taxes, resulting from this license. Neither party may bring an action,
regardless of form, more than two years after the cause of action arose. If you acquired the
Program in the United States, this license is governed by the laws of the State of New York.
If you acquired the Program in Canada, this license is governed by the laws of the Province
of Ontario. Otherwise, this license is governed by the laws of the country in which you
acquired the Program.
Typeface Trademark Acknowledgement
All resident fonts in this printer are licensed from Monotype Imaging Inc.
Helvetica, Palatino and Times are registered trademarks of Linotype-Hell AG.
ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC Zapf Dingbats are
registered trademarks of International Typeface Corporation.
Monotype Imaging License Agreement
vi
1
“Software” shall mean the digitally encoded, machine readable, scalable outline data
as encoded in a special format as well as the UFST Software.
2
You agree to accept a non-exclusive license to use the Software to reproduce and
display weights, styles and versions of letters, numerals, characters and symbols
(“Typefaces”) solely for your own customary business or personal purposes at the
address stated on the registration card you return to Monotype Imaging. Under the
terms of this License Agreement, you have the right to use the Fonts on up to three
printers. If you need to have access to the fonts on more than three printers, you
need to acquire a multi-user license agreement which can be obtained from
Monotype Imaging. Monotype Imaging retains all rights, title and interest to the
Software and Typefaces and no rights are granted to you other than a License to use
the Software on the terms expressly set forth in this Agreement.
3
To protect proprietary rights of Monotype Imaging, you agree to maintain the
Software and other proprietary information concerning the Typefaces in strict
confidence and to establish reasonable procedures regulating access to and use of
the Software and Typefaces.
4
You agree not to duplicate or copy the Software or Typefaces, except that you may
make one backup copy. You agree that any such copy shall contain the same
proprietary notices as those appearing on the original.
5
This License shall continue until the last use of the Software and Typefaces, unless
sooner terminated. This License may be terminated by Monotype Imaging if you fail
to comply with the terms of this License and such failure is not remedied within thirty
(30) days after notice from Monotype Imaging. When this License expires or is
terminated, you shall either return to Monotype Imaging or destroy all copies of the
Software and Typefaces and documentation as requested.
6
You agree that you will not modify, alter, disassemble, decrypt, reverse engineer or
decompile the Software.
7
Monotype Imaging warrants that for ninety (90) days after delivery, the Software will
perform in accordance with Monotype Imaging-published specifications, and the
diskette will be free from defects in material and workmanship. Monotype Imaging
does not warrant that the Software is free from all bugs, errors and omissions.
The parties agree that all other warranties, expressed or implied, including warranties
of fitness for a particular purpose and merchantability, are excluded.
8
Your exclusive remedy and the sole liability of Monotype Imaging in connection with
the Software and Typefaces is repair or replacement of defective parts, upon their
return to Monotype Imaging.
In no event will Monotype Imaging be liable for lost profits, lost data, or any other
incidental or consequential damages, or any damages caused by abuse or
misapplication of the Software and Typefaces.
9
Massachusetts U.S.A. law governs this Agreement.
10 You shall not sublicense, sell, lease, or otherwise transfer the Software and/or
Typefaces without the prior written consent of Monotype Imaging.
11 Use, duplication or disclosure by the Government is subject to restrictions as set
forth in the Rights in Technical Data and Computer Software clause at FAR 252-2277013, subdivision (b)(3)(ii) or subparagraph (c)(1)(ii), as appropriate. Further use,
duplication or disclosure is subject to restrictions applicable to restricted rights
software as set forth in FAR 52.227-19 (c)(2).
12 YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT,
UNDERSTAND IT, AND AGREE TO BE BOUND BY ITS TERMS AND
CONDITIONS. NEITHER PARTY SHALL BE BOUND BY ANY STATEMENT OR
REPRESENTATION NOT CONTAINED IN THIS AGREEMENT. NO CHANGE IN
THIS AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED BY
PROPERLY AUTHORIZED REPRESENTATIVES OF EACH PARTY.
vii
Conventions
This manual uses the following conventions:
Convention
Description
Example
Bracket Bold Used to emphasize the selection of
Text Typeface the operation panel key.
Press the [Print] key.
Bracket Text
Typeface
Press [Interface].
Used to emphasize the selection of
the touch panel key.
Italic Typeface Used to denote messages or names Processing message is
displayed on the operation panel,
displayed.
names of machine parts and for
references to additional information
and other publications.
viii
Notes
Used to provide additional or useful
NOTE: You can set the
information about a function or
feature. Can also contain references emulation for each interface.
to other publications.
Important
Use to provide important information.
IMPORTANT: Formatting of the
memory card must be executed
from the printer.
Contents
1
Procedure for Making Settings
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Menu Hierarchical Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
e-MPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Print Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2
Selecting the Printer Settings
Status Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Understanding the Status Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Changing the Interface Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Changing Network Interface Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Emulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Emulation Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
KPDL (AUTO) Alternative Emulation Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
KPDL Error Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
KC-GL Pen and Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Default Font . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Selecting the Default Font . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Changing the Default Font Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Character Pitch for Courier/Letter Gothic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Selecting Regular or Dark Courier/Letter Gothic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Setting the Code Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Printing Lists of Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Print Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Number of Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Print Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Page Protect Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Line Feed (LF) Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Carriage-Return (CR) Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Setting Print Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
KIR Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
Eco Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Print Density Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Paper Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
MP Tray Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Selecting the Paper Feed Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Duplex Print Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
Output Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
Overriding Difference between A4 and Letter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Operating the Storage Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Using the Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Using the RAM Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
Using the Optional Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
ix
e-MPS Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Printing a Quick Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Using Proof-and-Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
Printing a Private Print/Job Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
Retrieving Jobs from Virtual Mailbox (VMB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41
Printing a List of Virtual Mailbox (VMB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
Printing a List of Code Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
Changing e-MPS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
Other Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46
Automatic Form Feed Timeout Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46
Resource Protect Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47
Auto Error Clear Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47
Finishing Error Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
Printing the Service Status Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49
Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-50
Received Data Dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-50
3
Troubleshooting
Basic troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Display message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Storage Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
RAM Disk Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Memory Card Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Hard Disk Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Pausing Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Canceling Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
4
Options
5
Specifications
x
1 Procedure for Making Settings
This chapter explains how to use the operator panel to configure the printer function and
shows the hierarchy diagram of the menu selection.
Procedure
To enter the printing function, perform the following procedure.
1
Press the [Print] key. The machine enters the
printer mode.
2
Press [Printer Menu] or [e-MPS]. The
Printer Menu or e-MPS screen will
appear.
Ready to print.
e-MPS
Printer
Menu
3
4
Select the desired settings that you
want to make. For details, refer to
Selecting the Printer Settings on
page 2-1.
Cancel
Select item.
Printer menu
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Paper
Handling
Others
RAM DISK
Mode
When the setting is completed, press [Close]. The setting is decided, returns to the before
screen.
NOTE: To cancel the setting, press [Back]. The setting value is cleared and the previous
value is set again.
1-1
Procedure for Making Settings
Menu Hierarchical Diagram
The following is the hierarchy diagram of the menu selection system of the printer.
These items will not appear unless the printer is installed with the applicable
option unit.
e-MPS
Quick Copy
User
` Job
` 1 to 999 (Set)
` Printing
Delete
Private/Stored
` User
` Job
` 1 to 999 (Set)
Delete
Print VMB Data Tray Job
`
List of VMB
` Printing
List of Code JOB
` Printing
Configuration
` Quick Copy
1-2
` Printing
` 0 to 50 (Job)
Temporary Code
JOB Size
`
0 to 9999 (MB)
Permanent Code
JOB Size
`
VMB Size
` 0 to 9999 (MB)
0 to 9999 (MB)
` ID-code
`Printing
Procedure for Making Settings
Print Menu
Print Status Page ` Printing
Interface
` Network
` Netware
` On, Off
Auto, 802.3, Ethernet II, 802.2, 802.3SNAP
TCP/IP
AppleTalk
` On, Off
DHCP
` On, Off
BOOTP
` On, Off
IP Address
` ###.###.###.###
Subnet Mask
` ###.###.###.###
Gateway
` ###.###.###.###
` On, Off
Network Status Page On, Off
`
USB
Option
` Netware
` On, Off
Auto, 802.3, Ethernet II, 802.2, 802.3SNAP
TCP/IP
Emulation
` On, Off
DHCP
` On, Off
BOOTP
` On, Off
IP Address
` ###.###.###.###
Subnet Mask
` ###.###.###.###
Gateway
` ###.###.###.###
AppleTalk
` On, Off
Opt. Status Page
` On, Off
` PCL6
KPDL
` Print KPDL errors ` On, Off
KPDL (AUTO)
` Alt Emulation
` PCL6, KC-GL, Line Printer, IBM Proprinter,
Diabro 630, EPSON LQ-850
Print KPDL errors ` On, Off
KC-GL
` Pen Adjust
Page Set
` Pen (1) to (8)
` 1 to 99 (dots)
` A2, A1, A0, B3, B2, B1, B0, SPSZ
Line Printer
IBM Proprinter
Diabro 630
EPSON LQ-850
Font
` Font selection
` Font ID
Detail
` ####
` 4.00 to 999.75 (Point)
0.44 to 99.99 (CPI)
Courier
Internal, Dark
Letter Gothic
Internal, Dark
Code Set
` ########
Internal
` Printing
Option font
` Printing
1-3
Procedure for Making Settings
Page Set
Print Quality
Paper Handling
` Copies
` 1 to 999 (Set)
Orientation
` Portrait, Landscape
Zoom(Reduce)
` Page Size
` ####
Print Size
` ####
Page Protect
` Auto, On
LF Action
` LF only, CR and LF, Ignore LF
CR Action
` CR only, CR and LF, Ignore CR
` KIR Mode
` On, Off
Eco Print
` On, Off
Resolution
` Fast1200 Mode, 600 dpi, 300 dpi
Print Density
` 1 to 5
` MP Tray Mode
` Cassette, First
Feed Select
` 1st , 2nd paper, MP tray
Duplex Mode
` None, Short edge bind, Long edge bind
Paper Output
` Top tray
Finisher Tray
Face down, Face up
Override A4/Letter ` On, Off
RAM Disk Mode
` On, Off
Write Data
Hard Disk
1-4
List of Partitions
` Printing
RAM Disk Size
` 1 to 28 (MB)
Read Data
` ########
` Enter
Read Program
` ########
` Enter
Delete Data
` ########
` Delete
Delete Program
` ########
` Delete
Delete Font
` ########
` Delete
Delete Macro
` ########
` Delete
` Write Data
List of Partitions
` Printing
Format
` Yes, No
Read Data
` ########
` Enter
Read Program
` ########
` Enter
Delete Data
` ########
` Delete
Delete Program
` ########
` Delete
Delete Font
` ########
` Delete
Delete Macro
` ########
` Delete
3rd ,4th paper
Procedure for Making Settings
Memory Card
Others
` Write Data
List of Partitions
` Printing
Format
` Yes, No
Read Data
` ########
` Enter
Read Program
` ########
` Enter
Read Font
` ########
` Enter
Read Macro
` ########
` Enter
Delete Data
` ########
` Delete
Delete Program
` ########
` Delete
Delete Font
` ########
` Delete
Delete Macro
` ########
` Delete
Delete Language ` ########
` Delete
` Form Feed Time Out 0 to 495 (Seconds)
`
Resource Protect ` Off, Permanent, Permanent/Temporary
Auto Continue
` On, Off
0 to 495 (Seconds)
Finishing Error
` Proces. Duplex print On, Off
`
Staple Mode
` On, Off
Service
` Print Status page ` Printing
Printer Reset
` Yes, No
Print HEX-DUMP ` Yes, No
1-5
Procedure for Making Settings
1-6
2 Selecting the Printer Settings
This chapter provides the information you need to configure this machine. In general you
need to use the operator panel only to make default settings. You can make most changes
to the printer settings using the printer driver through the application software.
NOTE: Changes to printer settings made using a software application override changes
made using the operator panel.
This chapter contains explanations on the following topics:
•
Status Pages
•
Changing the Interface Parameters
•
Emulation Mode
•
Default Font
•
Print Configuration
•
Setting Print Quality
•
Paper Handling
•
Operating the Storage Device
•
e-MPS Function
•
Other Modes
2-1
Selecting the Printer Settings
Status Pages
This section explains the procedure for printing the status pages. The status page is a list
of parameters and settings for most basic machine configurations. You may be required to
produce a status page when requesting service to the machine.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Print Status Page].
Select item.
Printer menu
4
Press [Printing].
The message Processing data
appears and the machine prints a
status page.
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Paper
Handling
Others
RAM DISK
Mode
Stop
e
Letter
Printing
5
2-2
After the status page is printed, the display returns to the Printer menu screen.
Selecting the Printer Settings
Understanding the Status Page
The numbers in the following diagram refer the items explained below the diagram.
NOTE: The items and values on the status page may vary depending on the machine's
firmware version.
1
2
3
4
5
7
6
8
9
10
2-3
Selecting the Printer Settings
1
Firmware Version
This item shows the version and release date of the machine firmware.
2
Hardware Information
This item shows various machine settings for hardware-related items.
3
Memory
This shows the amount of total memory installed in the machine, the amount of
currently available memory, and the current status of the RAM disk.
4
Page Information
This shows the print resolution, number of copies, and the total page count.
5
Installed Options
This item shows the options installed in the machine.
6
Network Status
This item shows the IP address, subnet mask address, and gateway address for
the network interface card in the machine.
7
Emulation
This item shows all available emulations of the machine. The PCL6 emulation is
set as default when the machine is shipped from the factory.
8
Error Log
This item shows the last three instances of the following types of errors, listing
them in the order of occurrence:
•
•
•
•
KPDL (PostScript) errors
Memory overflow
Print overrun
File-not-found
The most recent error is displayed on the top line of the Error Log. For error
remedies, refer to Display message on page 3-2. Error information is cleared
when the printer’s power is turned off.
9
Interface Information
This information shows the emulation and the default font for all interfaces
installed in the machine.
10 Test pattern
KIR is the original smoothing function. This test pattern shows the effect of the
KIR (Kyocera Image Refinement) system.
2-4
Selecting the Printer Settings
Changing the Interface Parameters
The machine is equipped with both parallel and USB interfaces. Optional network interface
card can also be installed. Various printing environment parameters such as the default
emulation can be changed independently on different interfaces by using the machine’s
menu selection system. Select the interface to apply the changes in the procedure
described below.
Interface
Setting Item
Value
NetWare
TCP/IP
AppleTalk
Network Status Page
On
On
On
On
Change #
Network
USB
Printer menu
Interface
Setting Item
Value
NetWare
TCP/IP
AppleTalk
Opt. Status Page
On
On
On
On
Change #
Network
USB
Option
Printer menu - Interface
NOTE: This interface selection described below does not select the interface from which
data will be received. The machine automatically selects the interface.
Changing Network Interface Parameters
This machine supports TCP/IP, IPX/SPX, NetBEUI, and Appletalk protocols. In addition,
you can install the optional network interface card in the option interface slot.
Using the operator panel, you can:
•
Activate or deactivate TCP/IP, NetWare, and AppleTalk
•
Activate or deactivate DHCP
•
Enter IP address, subnet mask address, and default gateway address
•
Determine whether to print a network status page when the machine is turned on
NOTE: The operations of the optional network interface are the same as those of the
network interface.
TCP/IP
Turn this setting On when this machine is connected to a Windows network, etc., using
TCP/IP.
2-5
Selecting the Printer Settings
NOTE: Before setting the IP Address, ask your Network Administrator to obtain the
address and prepare it. If you use the following procedure to manually register the IP
address, be sure to turn the DHCP setting Off and the TCP/IP setting On.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Interface].
Select item.
Printer menu
4
Press [Network] tab.
Paper
Handling
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Others
RAM DISK
Mode
Interface
Setting Item
When option network interface sets,
press [Option] tab.
Value
NetWare
TCP/IP
AppleTalk
Network Status Page
On
On
On
On
Change #
Network
USB
Printer menu
5
Press S or T to select TCP/IP and press [Change #].
6
Press [On].
7
Press S or T to select DHCP and
press [Change #].
Back
TCP/IP
TCP/IP
Setting Item
Off
DHCP
BOOTP
IP Address
Subnet Mask
Gateway
On
Printer menu - Interface
8
Press [Off] and press [Close].
9
Press S or T to select BOOTP and
press [Change #].
Value
Off
Off
192. 168 . 110. 204
255. 255. 248. 0
192. 168 . 39. 254
- Network
TCP/IP
Back
TCP/IP
Setting Item
Off
DHCP
BOOTP
IP Address
Subnet Mask
Gateway
On
Printer menu - Interface
2-6
- Network
- TCP/IP
Value
Off
Off
192. 168 . 110. 204
255. 255. 248. 0
192. 168 . 39. 254
Selecting the Printer Settings
10
Press [Off] and press [Close].
11
Press S or T to select IP Address
and press [Change #].
Back
Setting Item
DHCP
BOOTP
IP Address
Subnet Mask
Gateway
nterface
12
Use the numeric keys to enter the
address. Enter the 3-digit address in
the highlighted area and press the [#]
key.
- Network
IP Address
Back
- Network
0
0
(with #key)
- TCP/IP
IP Address
Back
192
Printer menu - Interface
Use the same procedure to enter the
remaining address and then press
[Close]. The display returns to the
TCP/IP screen.
0
Confirm per 3 lines pressing # key.
To modify the entered address, press
the [#] key to select the 3-digit
address to be modified and use the
numeric keys to enter the address
again.
14
Change #
Confirm per 3 lines pressing # key.
Printer menu - Interface
Enter the next 3-digit address and
press the [#] key.
Value
Off
Off
192. 168 . 110. 204
255. 255. 248. 0
192. 168 . 39. 254
- TCP/IP
192
13
Close
168
- Network
0
0
(with #key)
- TCP/IP
IP Address
Back
Confirm per 3 lines pressing # key.
192
168
110
204
(with #key)
If you press [Back], the entered
address is cleared and the previous
address is set again.
Printer menu - Interface
15
- Network
Press S or T to select Subnet Mask
and press [Change #].
Back
Setting Item
DHCP
BOOTP
IP Address
Subnet Mask
Gateway
nterface
16
- TCP/IP
Close
Value
Off
Off
192. 168 . 110. 204
255. 255. 248. 0
192. 168 . 39. 254
Change #
- Network
Enter the Subnet Mask address using the same procedure used for the IP Address in steps
12 through 14 of IP Address Setting.
2-7
Selecting the Printer Settings
17
Press S or T to select Gateway and
press [Change #].
Back
Setting Item
DHCP
BOOTP
IP Address
Subnet Mask
Gateway
nterface
Close
Value
Off
Off
192. 168 . 110. 204
255. 255. 248. 0
192. 168 . 39. 254
Change #
- Network
18
Enter the Gateway address using the same procedure used for the IP Address in steps 12
through 14 of IP Address Setting.
19
Press [Close] and returns to the Interface screen.
20
Press [Close] and returns to the Printer menu screen.
NetWare
Set this item to On when you connect to a network using NetWare. Frame mode can be
selected from Auto, 802.3, Ethernet II, 802.2, and 802.3SNAP.
1
Access Interface, refer to TCP/IP on page 2-5.
2
Press S or T to select Netware and press [Change #].
3
Press [On] and select the frame type.
NetWare
Back
Frame Type
NetWare
Off
On
Auto
802.2
802.3
802.3SNAP
EthernetII
Printer menu - Interface - Network
4
Press [Close] and returns to the Interface screen.
5
Press [Close] and returns to the Printer menu screen.
AppleTalk
Set this option to On if connecting to an Apple Macintosh computer.
1
2-8
Access Interface, refer to TCP/IP on page 2-5.
Selecting the Printer Settings
2
Press S or T to select AppleTalk
and press [Change #].
Interface
Setting Item
Value
NetWare
TCP/IP
AppleTalk
Network Status Page
On
On
On
On
Change #
Network
USB
Printer menu
3
Select [On].
4
Press [Close] and returns to the Interface screen.
5
Press [Close] and returns to the Printer menu screen.
Network Status Page Printing
You can have your machine print out a network status page when the machine prints the
status page. The network status page shows the network addresses, and other information
under various network protocols about the network interface card. The default setting is Off
(print disable).
1
Access Interface, refer to TCP/IP on page 2-5.
2
Press S or T to select Network
Status Page and press [Change #].
Interface
Setting Item
Value
NetWare
TCP/IP
AppleTalk
Network Status Page
On
On
On
On
Change #
Network
USB
Printer menu
3
Select [On].
4
Press [Close] and returns to the Interface screen.
5
Press [Close] and returns to the Printer menu screen.
2-9
Selecting the Printer Settings
Emulation Mode
This section explains the procedure to select the emulation protocol.
NOTE: You can set the emulation for each interface.
Emulation Mode Selection
Emulation modes that can be used with this machine: PCL6, KPDL, KPDL(AUTO), KC-GL,
Line Printer, IBM Proprinter, Diabro 630, and EPSON LQ-850
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Emulation].
Select item.
Printer menu
4
Select the desired interface tab.
Paper
Handling
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Others
RAM DISK
Mode
Emulation
PCL6
Line
Printer
KPDL
IBM
Proprinter
KPDL
(AUTO)
Diablo 630
KC-GL
EPSON
LQ-850
Network
USB
Printer menu
5
Select the desired emulation mode.
IMPORTANT: If you set KPDL(AUTO), switching between KPDL and an alternative
emulation mode will be automatically performed according to the print data. If you set KPDL
or KPDL(AUTO), the details of any error that occurs during printing can be printed. If you
set KC-GL, you can set the thickness of the pen and page size.
6
On completion, Press [Close] and returns to the Printer menu screen.
KPDL (AUTO) Alternative Emulation Selection
If you set KPDL(AUTO), switching between KPDL and an alternative emulation mode will
be automatically performed according to print data.
Available emulation modes: PCL6, KC-GL, Line Printer, IBM Proprinter, Diabro 630, and
EPSON LQ-850
2-10
Selecting the Printer Settings
1
Access Emulation, refer to Emulation Mode Selection on page 2-10.
2
Press [KPDL(AUTO)].
3
Press [Alt. Emulation].
Close
Line
Printer
IBM
Proprinter
Diablo 630
EPSON
LQ-850
Alt.
Emulation
Print KPDL
errors
USB
4
Select the desired alternative emulation mode.
5
Press [Close] and returns to the Emulation screen.
KPDL Error Printing
The details of any error that occurs during printing in the KPDL emulation mode can be
printed.
1
Access Emulation, refer to Emulation Mode Selection on page 2-10.
2
Select [KPDL] or [KPDL(AUTO)].
3
Press [Print KPDL errors].
Close
Line
Printer
IBM
Proprinter
Diablo 630
EPSON
LQ-850
Print KPDL
errors
USB
4
Select [On].
5
Press [Close] and returns to the Emulation screen.
KC-GL Pen and Page
If you have selected KC-GL emulation, you can set the thicknesses, color and the page
size.
1
Access Emulation, refer to Emulation Mode Selection on page 2-10.
2
Press [KC-GL].
2-11
Selecting the Printer Settings
3
Press [Pen Adjust].
Close
Line
Printer
IBM
Proprinter
Page Set
Diablo 630
EPSON
LQ-850
Pen Adjust
USB
4
Press S or T to select Pen Adjust
and press [Change #].
Pen Adjust
Setting Item
Pen(1)
Pen(2)
Pen(3)
Pen(4)
Pen(5)
Pen(6)
Pen(7)
Value
1
2
3
4
5
6
7
dots
dots
dots
dots
dots
dots
dots
Change #
#
Change
Printer menu - Emulation
5
Press [+] or [-] or use the numeric
keys to enter the desired pen width
and select the desired pen color.
Back
Pen Width
(1 ~ 99)
1
Emulation
dot(s)
- KC-GL
6
Press [Close] twice and returns to the Emulation screen.
7
Press [Page Set].
8
Select the desired page size.
NOTE: SPSZ is the size specified with the PRESCRIBE SPSZ command.
9
10
2-12
Press [Close] and returns to the Emulation screen.
Press [Close] and returns to the Printer menu screen.
Close
Selecting the Printer Settings
Default Font
You can select the default font for the current interface. The default font can be one of the
internal fonts or a font that is downloaded to the machine memory or stored on memory
card or hard disk.
The following settings are available:
•
Selecting the Default Font
•
Changing the Default Font Size
•
Character Pitch for Courier/Letter Gothic
•
Selecting Regular or Dark Courier/Letter Gothic
•
Setting the Code Set
•
Printing Lists of Fonts
NOTE: You can set the font for each interface.
Selecting the Default Font
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Font].
Select item.
Printer menu
4
Press [Font selection].
Paper
Handling
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Others
RAM DISK
Mode
Back
Font
Code Set
Font
selection
Code Set
Printer menu
5
Select the desired interface tab.
Back
Font
Courier
I000
Font ID
Internal
Dark
Detail
Network
USB
Printer menu - Font
2-13
Selecting the Printer Settings
6
Press S or T to select font ID.
Characters displayed before font numbers indicate the following items. For internal font
numbers, refer to Printing Lists of Fonts on page 2-16.
Display
Description
I
Internal font
S
Downloaded fonts
M
Fonts in memory card
H
Fonts in RAM disk or hard disk
O
Fonts in optional ROM
7
Press [Close] and returns to the Font screen.
8
Press [Close] and returns to the Printer menu screen.
Changing the Default Font Size
If you have selected a proportional font as the default font, you can set the font size. If you
have selected the Courier font or the Letter Gothic font as the default font, only the
Character Pitch setting displays.
1
Access Font, refer to Selecting the Default Font on page 2-13.
2
Press [Font selection].
3
Press [Detail].
Back
Font
Courier
I000
Font ID
Internal
Dark
Detail
Network
USB
Printer menu - Font
4
Press [+] or [-] or use the numeric
keys to enter the character size. The
character size can be set between 4
and 999.75 points, in 0.25-point
increments.
Back
Configuration
(4.00 ~ 999.75)
Size
4.00
Point
(0.25)
(0.25)
Printer menu - Font
5
2-14
Press [Close] and returns to the Font screen.
Selecting the Printer Settings
Character Pitch for Courier/Letter Gothic
You can set the character pitch for fixed fonts when the default font is Courier or Letter
Gothic.
1
Access Font, refer to Selecting the Default Font on page 2-13.
2
Press [Font selection].
3
Press [Detail].
Back
Font
Courier
I000
Font ID
Internal
Dark
Detail
Network
USB
Printer menu - Font
4
Press [+] or [-] or use the numeric
keys to enter the character pitch. The
character pitch can be set between
0.44 and 99.99 characters per inch,
in 0.01 character-per-inch
increments.
Back
Configuration
(0.44 ~ 99.99)
Pitch
0.44
CPI
(0.01)
(0.01)
Printer menu - Font
5
Press [Close] and returns to the Font screen.
Selecting Regular or Dark Courier/Letter Gothic
Courier or Letter Gothic font thickness can be selected as Internal or Dark.
1
Access Font, refer to Selecting the Default Font on page 2-13.
2
Press [Font selection].
3
Press [Internal] or [Dark] under
Courier and Letter Gothic area.
Close
Back
Courier
Letter Gothic
I000
nt ID
Internal
Internal
Dark
Dark
Detail
USB
Font
4
Press [Internal] or [Dark] under Letter Gothic area.
5
Press [Close] and returns to the Font screen.
2-15
Selecting the Printer Settings
Setting the Code Set
You can change the character code set. Available character code sets vary depending on
the current font. (The default is IBM PC-8.)
1
Access Font, refer to Selecting the Default Font on page 2-13.
2
Press [Code Set].
Back
Code Set
Code Set
Close
Printing list
Internal
Option
font
3
Select the desired interface tab.
Back
Code Set
Code Set
IBM PC-8
PC-855 Serbia
ISO Cyrillic
PC-863 Canada
PC-861 Iceland
PC-860 Portugal
Network
Up
Down
USB
Printer menu - Font
4
Press S or T to select the desired code set.
5
Press [Close] and returns to the Font screen.
6
Press [Close] and returns to the Printer menu screen.
Printing Lists of Fonts
To help you decide in selecting a font, you can printout lists of the internal fonts or the
optional fonts including downloaded fonts.
1
Access Font, refer to Selecting the Default Font on page 2-13.
2
Press [Internal] or [Option font] under
Printing list area.
Option font is displayed only when
there are optional fonts available,
such as those contained in the
optional Memory Card.
3
2-16
Press [Printing].
Back
Code Set
Code Set
Close
Printing list
Internal
Option
font
Selecting the Printer Settings
The message Processing data appears and the machine prints a list of fonts. Sample lists
of fonts are shown in the following illustration.
After the list is printed, and returns to the Printer menu screen.
2-17
Selecting the Printer Settings
Print Configuration
The following settings are available:
•
Number of Copies
•
Print Orientation
•
Zoom
•
Page Protect Mode
•
Line Feed (LF) Action
•
Carriage-Return (CR) Action
NOTE: You can set the print configuration for each interface.
Number of Copies
You can set the number of copies of each page to be printed for the current interface. The
number of copies can be set between 1 and 999.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Page Set].
Select item.
Printer menu
4
Press S or T to select Copies and
press [Change #].
Paper
Handling
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Others
RAM DISK
Mode
Page Set
Setting Item
Copies
Orientation
Zoom(Reduce)
Page Protect
LF Action
CR Action
Wide A4
Value
001
[ Cassette] - [ Cassette]
Auto
Off
Change #
Printer menu
5
Press [+] or [-] or use the numeric
keys to enter the number of copies.
Back
Copies
(1 ~ 999)
1
Printer menu - Page Set
2-18
Set (Enter with #-key)
Selecting the Printer Settings
6
Press [Close] and returns to the Page Set screen.
7
Press [Close] and returns to the Printer menu screen.
Print Orientation
You can select portrait (upright) or landscape (sideways) page orientation.
Portrait Orientation
Landscape Orientation
ABC
ABC
1
Access Page Set, refer to Number of Copies on page 2-18.
2
Press S or T to select Orientation
and press [Change #].
Page Set
Setting Item
Value
Copies
Orientation
Zoom(Reduce)
Page Protect
LF Action
CR Action
Wide A4
001
[ Cassette] - [ Cassette]
Auto
Off
Change #
Printer menu
3
Select the desired interface tab.
Back
Orientation
Portrait
Landscape
Network
Printer menu
USB
- Page Set
4
Press [Portrait] or [Landscape].
5
Press [Close] and returns to the Page Set screen.
6
Press [Close] and returns to the Printer menu screen.
Zoom
If you specify the Paper Size (original size) and the Output Size, the machine reduces the
image at a preset magnification ratio to print onto the specified Output Size paper.
1
Access Page Set, refer to Number of Copies on page 2-18.
2-19
Selecting the Printer Settings
2
Press S or T to select
Zoom(Reduce) and press [Change
#].
Page Set
Setting Item
Copies
Orientation
Zoom(Reduce)
Page Protect
LF Action
CR Action
Wide A4
Value
001
[ Cassette] - [ Cassette]
Auto
Change #
Off
Printer menu
3
Press S or T to select the desired
page size and print size.
Back
Zoom(Reduce)
Page Size
The reduction ratio will automatically
be set and displayed.
Zoom
100
%
Cassette
Print Size
Cassette
Printer menu
- Page Set
4
Press [Close] and returns to the Page Set screen.
5
Press [Close] and returns to the Printer menu screen.
Page Protect Mode
The Page Protect Menu does not normally appear, however, Page Protect will be forcibly
set to On if a print overrun error occurs because the print job is too complex. When this has
happened, be sure to reset Page Protect to Auto (default) in order to maintain the optimum
use of machine memory.
1
Access Page Set, refer to Number of Copies on page 2-18.
2
Press S or T to select Page Protect
and press [Change #].
Page Set
Setting Item
Copies
Orientation
Zoom(Reduce)
Page Protect
LF Action
CR Action
Wide A4
Value
001
[ Cassette] - [ Cassette]
Auto
Off
Change #
Printer menu
3
Press [Auto].
4
Press [Close] and returns to the Page Set screen.
5
Press [Close] and returns to the Printer menu screen.
Line Feed (LF) Action
This procedure instructs the machine what to do when it receives a linefeed code (0AH).
2-20
Selecting the Printer Settings
1
Access Page Set, refer to Number of Copies on page 2-18.
2
Press S or T to select LF Action and
press [Change #].
Page Set
Setting Item
Value
Copies
Orientation
Zoom(Reduce)
Page Protect
LF Action
CR Action
001
[ Cassette] - [ Cassette]
Auto
Wide A4
Change #
Off
Printer menu
3
Select the desired interface tab.
Back
LF Action
LF only
CR and LF
Ignore LF
Network
Printer menu
4
USB
- Page Set
Press the desired linefeed action.
LF only
Linefeed is performed (Default).
CR and LF
A linefeed and carriage return are performed.
Ignore LF
The linefeed is ignored.
5
Press [Close] and returns to the Page Set screen.
6
Press [Close] and returns to the Printer menu screen.
Carriage-Return (CR) Action
This procedure instructs the machine what to do when it receives a carriage-return code
(0DH).
1
Access Page Set, refer to Number of Copies on page 2-18.
2
Press S or T to select CF Action
and press [Change #].
Page Set
Setting Item
Copies
Orientation
Zoom(Reduce)
Page Protect
LF Action
CR Action
Wide A4
Value
001
[ Cassette] - [ Cassette]
Auto
Off
Change #
Printer menu
2-21
Selecting the Printer Settings
3
Select the desired interface tab.
Back
CR Action
CR only
CR and LF
Ignore CR
Network
Printer menu
4
2-22
USB
- Page Set
Press the desired carriage-return action.
CF only
A carriage-return is performed (Default).
CR and LF
A linefeed and carriage return are performed.
Ignore CF
The carriage-return is ignored.
5
Press [Close] and returns to the Page Set screen.
6
Press [Close] and returns to the Printer menu screen.
Selecting the Printer Settings
Setting Print Quality
The following settings are available:
•
KIR Mode
•
Eco Print
•
Print Density Adjustment
•
Print Density Adjustment
KIR Mode
Smoothing changes the print quality to 2400 dpi equivalent x 600 dpi.
With KIR Off
With KIR On (default)
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Print Quality].
Select item.
Printer menu
4
Press S or T to select KIR Mode
and press [Change #].
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Paper
Handling
Others
RAM DISK
Mode
Print Quality
Setting Item
KIR Mode
EcoPrint Mode
Resolution
Print Density
Value
On
Off
Fast 1200 Mode
Density 3
Change #
Printer menu
5
Press [On] or [Off].
2-23
Selecting the Printer Settings
6
Press [Close] and returns to the Print Quality screen.
7
Press [Close] and returns to the Printer menu screen.
Eco Print
EcoPrint mode allows printing with less toner consumption. Use this mode when high
quality printing is not necessary, for example, for draft printing.
EcoPrint setting is Off (default).
EcoPrint setting is On
1
Access Print Quality, refer to KIR Mode on page 2-23.
2
Press S or T to select EcoPrint and
press [Change #].
Print Quality
Setting Item
KIR Mode
EcoPrint Mode
Resolution
Print Density
Value
On
Off
Fast 1200 Mode
Density 3
Change #
Printer menu
3
Press [On] or [Off].
4
Press [Close] and returns to the Print Quality screen.
5
Press [Close] and returns to the Printer menu screen.
Print Density Adjustment
The print density can be adjusted in five steps from 1 (light) to 5 (dark). Optimizes printing
when grayscale is too light.
1
Access Print Quality, refer to KIR Mode on page 2-23.
2
Press S or T to select Print Density
and press [Change #].
Print Quality
Setting Item
KIR Mode
EcoPrint Mode
Resolution
Print Density
Value
On
Off
Fast 1200 Mode
Density 3
Change #
Printer menu
2-24
Selecting the Printer Settings
3
Press [Lighter] or [Darker] to select
the print density from five steps from
1 (light) to 5 (dark).
Print Density
Back
Lighter
Darker
Printer menu - Print Quality
IMPORTANT: Adjusting too dark may cause thin lines thickened.
4
Press [Close] and returns to the Print Quality screen.
5
Press [Close] and returns to the Printer menu screen.
2-25
Selecting the Printer Settings
Paper Handling
The following settings are available:
•
MP Tray Mode
•
Selecting the Paper Feed Source
•
Duplex Print Mode
•
Output Destination
•
Overriding Difference between A4 and Letter
MP Tray Mode
The MP(Multi Purpose) tray can be used in either of two modes — Cassette or First. The
MP tray feed paper differently depending on the mode:
Item
Description
Cassette (default) The MP tray acts in the same manner as other paper sources. The
printer can feed paper from any paper source you command on the
printer driver. The cassette mode provides a faster printing speed
than the first mode.
First
The MP tray automatically feeds paper placed on the MP tray
overriding another paper source that is selected on the printer driver.
After all sheets in the MP tray have been used up (approximately 200
sheets), paper will be fed from the paper source originally selected.
This mode is convenient to feed paper of special size or type without
reloading the current paper source. However, the MP tray must be
kept empty if you desire to feed paper from the intended paper
source.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Paper Handling].
Select item.
Printer menu
2-26
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Paper
Handling
RAM DISK
Mode
Others
Selecting the Printer Settings
4
Press S or T to select Multi Purpose
tray mode and press [Change #].
Paper Handling
Setting Item
Value
Multi Purpose Tray mode
Cassette
Feed Select
Duplex Mode
Paper Output
Override A4/LT
1st paper
Off
Finisher tray(F down)
Off
Change #
Printer menu
5
Select [Cassette] or [First].
6
Press [Close] and returns to the Paper Handling screen.
7
Press [Close] and returns to the Printer menu screen.
Selecting the Paper Feed Source
You can select the paper source, from which the machine feeds paper as the default. If an
optional paper feeder(s) is installed, it is also available for the default paper source.
1
Access Paper Handling, refer to MP Tray Mode on page 2-26.
2
Press S or T to select Feed Select
and press [Change #].
Paper Handling
Setting Item
Multi Purpose Tray mode
Feed Select
Duplex Mode
Paper Output
Override A4/LT
Value
Cassette
1st paper
Off
Finisher tray(F down)
Off
Change #
Printer menu
3
Select the desired paper feed source.
4
Press [Close] and returns to the Paper Handling screen.
5
Press [Close] and returns to the Printer menu screen.
2-27
Selecting the Printer Settings
Duplex Print Mode
Use to set the binding position on finished prints for duplex printing.
Short Edge Bind
Binding at a short edge
Long Edge Bind
Binding at a long edge
1
Access Paper Handling, refer to MP Tray Mode on page 2-26.
2
Press S or T to select Duplex Mode
and press [Change #].
Paper Handling
Setting Item
Value
Cassette
Multi Purpose Tray mode
Feed Select
1st paper
Duplex Mode
Paper Output
Override A4/LT
Off
Finisher tray(F down)
Off
Change #
Printer menu
3
Select [None], [Short edge bind], or [Long edge bind].
4
Press [Close] and returns to the Paper Handling screen.
5
Press [Close] and returns to the Printer menu screen.
Output Destination
Use to set the paper Output Destination.
1
2-28
Access Paper Handling, refer to MP Tray Mode on page 2-26.
Selecting the Printer Settings
2
Press S or T to select Paper Output
and press [Change #].
Paper Handling
Setting Item
Multi Purpose Tray mode
Feed Select
Duplex Mode
Paper Output
Override A4/LT
Value
Cassette
1st paper
Off
Finisher tray(F down)
Off
Change #
Printer menu
3
Select the desired output tray and
select [Face down] or [Face up].
elect
Back
Output
Close
Output Side
Job
Separator
Top Tray
Face down
Finisher Tray
Face up
aper Handling
4
Press [Close] and returns to the Paper Handling screen.
5
Press [Close] and returns to the Printer menu screen.
Overriding Difference between A4 and Letter
When the Override A4/LT is turned On using the operator panel, the machine ignores the
difference between A4 and Letter paper sizes. Printing is performed without an error
message even if the actual paper size in the current cassette differs from the paper size
formatting the job. By default, this feature is Off.
1
Access Paper Handling, refer to MP Tray Mode on page 2-26.
2
Press S or T to select Override A4/
LT and press [Change #].
Paper Handling
Setting Item
Multi Purpose Tray mode
Feed Select
Duplex Mode
Paper Output
Override A4/LT
Value
Cassette
1st paper
Off
Finisher tray(F down)
Off
Change #
Printer menu
3
Press [On] or [Off].
4
Press [Close] and returns to the Paper Handling screen.
5
Press [Close] and returns to the Printer menu screen.
2-29
Selecting the Printer Settings
Operating the Storage Device
The machine supports three types of storage device; optional memory card, optional hard
disk, and RAM disk. The optional memory card and optional hard disk are installed into the
dedicated slots of the machine. The RAM disk is an allocated part of the printer's memory.
If the optional hard disk is installed in the machine, the e-MPS function will be available.
The basic operations of each storage device are the same. This section mainly explains
the operation of the memory card.
Using the Memory Card
When the optional Memory Card is installed in this machine, Read, Write and Delete can
be performed for different types of data.
The following options are available:
•
Formatting a Memory Card
•
Writing Data
•
Reading Data (Data, Program Data, Font Data, and Macro Data)
•
Deleting Data (Data, Program Data, Font Data, Macro Data, and Option Language)
•
Printing a List of Data Names (Partitions)
Inserting the Memory Card
1
Turn off the main switch.
IMPORTANT: Be sure to turn the main switch off before inserting or removing the Memory
Card.
2-30
2
Open the MP (Multi Purpose) Tray.
3
Remove the Memory Card Cover Holder from the
MP tray.
4
Attach the Memory Card Cover Holder to the
memory card.
Selecting the Printer Settings
5
Insert the Memory Card into the slot with the front
of the card facing the rear of the machine.
Formatting a Memory Card
A new memory card must be formatted before it can be used in the machine. Formatting
allows data to be written to the memory card.
IMPORTANT: Formatting will destroy any existing data on a storage device including a
used memory card. Formatting of the memory card must be executed from this machine.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Memory Card].
Select item.
Printer menu
4
Press [Format].
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Paper
Handling
Others
Memory
RAM DISK
Mode
Memory Card
All data in the memory card will be
delete. Are you sure? is displayed.
Read
Delete
Language
Write Data
List of
Partitions
Data
Program
Data
Format
Font
Macro
Font
Printer menu
5
Press [Yes].
Formatting of the memory card starts.
6
Formatting is finished, the display returns to the Printer menu screen.
Writing Data
Data can be written to a memory card until the card is full. When writing to a memory card,
a name is assigned to the file automatically. You can use the procedure explained in the
section Printing a List of Data Names (Partitions) on page 2-33 to print a list of data names
for confirmation.
2-31
Selecting the Printer Settings
1
Access Memory Card, refer to Formatting a Memory Card on page 2-31.
2
Press [Write Data].
Memory Card
The display will returns to the Printer
menu screen and the machine enter
a waiting for data state.
Read
Delete
Language
Write Data
List of
Partitions
Data
Program
Data
Format
Font
Macro
Font
Printer menu
3
Transmit the data from PC.
When data is received from a PC, the message Processing data appears. Once the
operation is finished, Waiting is displayed.
4
Press [GO].
This writes the file to the memory card and instructs the printer to automatically print out a
memory card write information page as shown below.
The file is written onto the memory card given a destination name (also referred to as a
partition name) which the printer automatically assigns one after another as follows:
DataS001 (first data), DataS002 (second data), DataS003 (third data)...
5
After the write information page is printed, the display returns to the Printer menu screen.
Reading Data
Reads the selected data, program data, font data, and macro data from the memory card.
1
Access Memory Card, refer to Formatting a Memory Card on page 2-31.
2
Select [Data], [Program], [Font], or
[Macro] under Read area.
Memory Card
Read
Delete
Language
Write Data
Printer menu
2-32
List of
Partitions
Data
Program
Data
Format
Font
Macro
Font
Selecting the Printer Settings
3
Press S or T to select the data
required and press [Enter].
The message Processing data
appears and the reading of data from
the memory card starts.
Read Data
Printer menu
4
Up
Data
DataS001
DataS002
DataS003
DataS004
DataS005
DataS006
DataS007
Down
- Memory Card
After reading of data is finished, the display returns to the Printer menu screen.
Deleting Data
Deletes the selected data, program data, font data, macro data, and option language from
the memory card.
1
Access Memory Card, refer to Formatting a Memory Card on page 2-31.
2
Press [Language], [Data], [Program],
[Font], or [Macro] under Delete area.
Close
Read
Delete
Language
Write Data
3
Press S or T to select the data
required and press [Delete].
The message Processing data
appears and the deleting of data from
the memory card starts.
List of
Partitions
Data
Program
Data
Program
Format
Font
Macro
Font
Macro
Delete Data
Data
DataS001
DataS002
DataS003
DataS004
DataS005
DataS006
DataS007
Printer menu
4
Up
Down
- Memory Card
After the deleting of data is finished, the display returns to the Printer menu screen.
Printing a List of Data Names (Partitions)
The machine prints a list of all data names (referred to as partitions) stored in a memory
card for reference. (Printing a list is also available for a font card.)
1
Access Memory Card, refer to Formatting a Memory Card on page 2-31.
2-33
Selecting the Printer Settings
2
Press [List of Partitions].
Memory Card
Read
Delete
Language
Write Data
List of
Partitions
Data
Program
Data
Format
Font
Macro
Font
Printer menu
3
Press [Printing].
The message Processing data appears and the list of partitions prints.
4
After the list of partitions is printed, the display returns to the Printer menu screen.
Using the RAM Disk
This machine is equipped with RAM disk functions. The RAM disk is a virtual disk unit that
uses a part of the memory. If you assign a certain size of the memory to the RAM disk, you
can use it for electronic sorting (for reduction of total print time) and storage and reading of
data. Also you can use the e-MPS function.
To activate RAM disk in the printer's memory, first you must set the RAM disk mode to On
and set the desired data size for the RAM disk as described in the following section. This
allows you to perform the following operations on the RAM disk.
•
Writing Data
•
Printing a List of Data Names (Partitions)
•
Reading Data (Data and Program Data)
•
Deleting Data (Data, Program Data, Font Data, and Macro Data)
IMPORTANT: The RAM disk can not be used when an optional hard disk is installed. The
RAM disk stores data only temporarily. When the machine is reset or turned off, the stored
data will be erased. The RAM disk is allocated within the printer's memory available to
users. If the size of the RAM disk is set too large, the printing speed may decrease or the
memory may become insufficient.
2-34
Selecting the Printer Settings
NOTE: The operations of the RAM disk are the same as those of the memory card. Refer
to the relevant sections Using the Memory Card on page 2-30.
Activating the RAM Disk
By default, the RAM disk is not activated (Off). To confirm the RAM disk size or activate the
RAM disk, proceed as follows:
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [RAM DISK Mode].
Select item.
Printer menu
4
Press [On].
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Paper
Handling
Others
RAM DISK
Mode
Back
RAM DISK Mode
Read
Delete
Write Data
Off
On
List of
Partitions
RAM Disk
Size
Printer menu
5
Press [Close].
Do you want to restart immediately? is displayed.
6
Press [Yes].
The machine restarts and the RAM disk mode is enabled.
Setting the RAM Disk Size
To use the RAM disk, activate and enter the desired size of the RAM disk in the manner
described below. The maximum RAM disk size can be calculated as follows:
aximum RAM disk size = Total printer memory - 36MB
For example, if the total memory installed in your printer is 64MB, you can set 28MB of
RAM disk. If you attempt to set the RAM disk size beyond this restriction, the printer
automatically round it down so that the size is always 36MB less than the total printer
memory.
2-35
Selecting the Printer Settings
IMPORTANT: To activate RAM disk in the printer's memory, first you must set the RAM
disk mode to On and set the desired size for the RAM disk.
1
Access RAM DISK Mode, refer to Activating the RAM Disk on page 2-35.
2
Press [RAM DISK Size].
Back
RAM DISK Mode
Read
Delete
Write Data
Off
On
List of
Partitions
RAM Disk
Size
Printer menu
3
Press [+] or [-] or use the numeric
keys to enter the RAM disk size.
Back
RAM DISK Size
The memory size to use as RAM disk can be set.
16
MB
Printer menu - RAM DISK Mode
4
Press [Close].
When memory size is changed, Do you want to restart immediately? is displayed.
5
Press [Yes].
The machine restarts and the RAM disk size is changed.
Using the Optional Hard Disk
Installing the optional hard disk into the printer allows you to use all of the e-MPS function.
To use the e-MPS function, refer to e-MPS Function on page 2-38. This allows you to
perform the following operations on the hard disk.
•
Writing Data
•
Printing a List of Data Names (Partitions)
•
Reading Data (Data and Program Data)
•
Deleting Data (Data, Program Data, Font Data, and Macro Data)
•
Formatting a Hard Disk
NOTE: The operations of the hard disk are the same as those of the memory card. Refer
to the relevant sections Using the Memory Card on page 2-30.
Formatting a Hard Disk
When a hard disk is inserted into the printer for the first time, it must be formatted before
use.
2-36
Selecting the Printer Settings
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Hard Disk].
Select item.
Printer menu
4
Press [Format].
Print Status Page
Font
Interface
Page Set
Emulation
Print
Quality
Paper
Handling
Hard Disk
Others
Hard Disk
Read
All data in the HDD will be deleted.
Are you sure? is displayed.
Delete
Write Data
List of
Partitions
Format
Printer menu
5
Press [Yes].
Formatting of the hard disk starts.
6
After the deleting of data is finished, the display returns to the Printer menu screen.
2-37
Selecting the Printer Settings
e-MPS Function
The e-MPS is an abbreviation for enhanced-Multiple Printing System which implements the
following functions that are available from the printer driver:
The following settings are available:
•
Printing a Quick Copy
•
Using Proof-and-Hold
•
Printing a Private Print/Job Storage
•
Retrieving Jobs from Virtual Mailbox (VMB)
•
Printing a List of Virtual Mailbox (VMB)
•
Printing a List of Code Jobs
•
Changing e-MPS Configuration
NOTE: To use the e-MPS functions, the optional Hard Disk must be installed. For details
on e-MPS, refer to the KX Driver User Guide. If the RAM Disk is switched On, the e-MPS
function can still be used for proof-and-hold jobs, private print jobs, and printing a list of
code jobs. Refer to Activating the RAM Disk on page 2-35.
Printing a Quick Copy
This mode enables you to print the requested number of copies of a job, simultaneously
storing the job on the hard disk. When additional copies are required, you can reprint the
required number of copies from the printer operator panel.
The default number of print jobs that can be stored on the hard disk is 32. This value can
be increased to up to 50 from the configuration menu.
IMPORTANT: When the number of jobs reaches the limit, the oldest job will be overwritten
by the new one. When the printer is turned off, all stored jobs will be deleted.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [e-MPS].
3
Press [Quick Copy].
Select item.
e-MPS
Quick Copy
List of
VMB
Private/
Stored
List of
Code JOB
Print VMB
Data Tray
2-38
Configuration
Selecting the Printer Settings
4
Press S or T to select the user
name required and press [Next].
Select the user name.
Up
User
DataH001
DataH002
DataH003
DataH004
DataH005
DataH006
DataH007
Down
e-MPS
5
Press S or T to select a job required
and press [Next].
Quick Copy
Job
Up
DataH001
DataH002
DataH003
DataH004
DataH005
DataH006
DataH007
Down
e-MPS
NOTE: If you want to delete a job, press S or T to select a job required and press
[Delete].
6
Press [+] or [-] or use the numeric
keys to enter the number of copies
and press [Printing].
Quick Copy
(1 ~ 999)
10
Set (Enter with #-key)
The message Processing data
appears and the printing starts.
e-MPS
7
After the printing is finished, and returns to the Printer menu screen.
Using Proof-and-Hold
When you print multiple copies, this mode first prints one copy so that you can proof it
before continuing to print the remaining copies. Since you can proof the printouts before
printing the remaining copies, wastage of paper can be reduced.
The printer prints one copy and, at the same time, saves the print job on the hard disk. You
can also change the number of copies when resuming printing from the operator panel.
When the printer is turned off, all stored jobs will be deleted.
Printing Remaining Copies of a Proof and Hold Job
Printing a Proof-and-Hold job on the operator panel is the same as printing a quick copy
job. Refer to the relevant sections Printing a Quick Copy on page 2-38.
2-39
Selecting the Printer Settings
Printing a Private Print/Job Storage
In private print, you can specify that a job is not printed until you release the job from the
operator panel. When sending the job from the application software, specify a 4-digit
access code in the printer driver. The job is released for printing by entering the access
code on the operator panel ensuring confidentiality of the print job. The data is cleared after
printing.
The job storage feature saves jobs on the hard disk for future printing, even if the printing
system is switched off. You can also use access codes to restrict the printing of forms.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [e-MPS].
3
Press [Private/Stored].
Select item.
e-MPS
Quick Copy
List of
VMB
Private/
Stored
List of
Code JOB
Configuration
Print VMB
Data Tray
4
Press S or T to select the user
name required and press [Next].
Select the user name.
User
DataH001
DataH002
DataH003
DataH004
DataH005
DataH006
DataH007
Up
Down
e-MPS
5
Press S or T to select a job required
and press [Next].
Private/Stored
Job
DataH001
DataH002
DataH003
DataH004
DataH005
DataH006
DataH007
Up
Down
e-MPS
NOTE: If you want to delete a job, press S or T to select a job required and press
[Delete].
2-40
Selecting the Printer Settings
6
Press [+] or [-] or use the numeric
keys to enter the number of copies.
and press [Printing].
Private/Stored
(1 ~ 999)
5
Set (Enter with #-key)
e-MPS
7
Press [Printing].
Enter ID-code is displayed.
8
Use the numeric keys to enter the
four-digit access code in the printer
driver and press [Enter].
Enter ID-code
ID ****
The message Processing data
appears and the printing starts.
Clear
Job name
9
(Enter with #-key)
****
After the printing is finished, and returns to the Printer menu screen.
Retrieving Jobs from Virtual Mailbox (VMB)
Virtual mailbox is part of Job Storage, which stores print jobs on the hard disk without
printing. It enables you to retrieve jobs later from the operator panel. When the job is printed
the data is deleted from the mailbox.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [e-MPS].
3
Press [Print VMB Data Tray].
Select item.
e-MPS
Quick Copy
List of
VMB
Private/
Stored
List of
Code JOB
Configuration
Print VMB
Data Tray
4
Press S or T to select a job required
and press [Printing].
Print VMB Data Tray
Job
The message Processing data
appears and the printing starts.
001
002
003
004
005
006
007
Up
Down
e-MPS
2-41
Selecting the Printer Settings
5
After the printing is finished, and returns to the Printer menu screen.
Printing a List of Virtual Mailbox (VMB)
A list can be printed which shows the current virtual mailbox numbers, the data stored in a
mailbox, the size of data stored and other information.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [e-MPS].
3
Press [List of VMB].
Select item.
e-MPS
Quick Copy
List of
VMB
Private/
Stored
List of
Code JOB
Configuration
Print VMB
Data Tray
4
Press [Printing].
The message Processing data appears and the printing starts.
5
After the printing is finished, and returns to the Printer menu screen.
Printing a List of Code Jobs
Permanent code jobs in the hard disk can be printed.
2-42
1
Press the [Print] key. The machine enters the printer mode.
2
Press [e-MPS].
Selecting the Printer Settings
3
Press [List of Code JOB].
Select item.
e-MPS
Quick Copy
List of
VMB
Private/
Stored
List of
Code JOB
Configuration
Print VMB
Data Tray
4
Press [Printing].
The message Processing data appears and the printing starts.
5
After the printing is finished, and returns to the Printer menu screen.
Changing e-MPS Configuration
The e-MPS settings such as the maximum number of documents that can be stored on the
hard disk and the capacity assigned to each function, can be changed.
The following settings are available:
•
Changing the Maximum Number of Quick Copy Jobs
•
Maximum Space Assigned to Temporary Code Jobs
•
Maximum Space Assigned to Permanent Code Jobs
•
Maximum Space Assigned to Virtual Mailboxes (VMB)
Changing the Maximum Number of Quick Copy Jobs
This changes maximum number of quick copy jobs from 0 to 50. The default is 32.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [e-MPS].
2-43
Selecting the Printer Settings
3
Press [Configuration].
Select item.
e-MPS
Quick Copy
List of
VMB
Private/
Stored
List of
Code JOB
Configuration
Print VMB
Data Tray
4
Press S or T to select Quick Copy
and press [Change #].
Configuration
Setting Item
Value
Quick Copy
Temporary Code JOB Size
Permanent Code JOB Size
VMB Size
32
200MB
100MB
100MB
Change #
e-MPS
5
Press [+] or [-] or use the numeric
keys to enter the maximum number
of jobs.
Back
Quick Copy
Able to adjust Max registration # of quick copy job.
(0 ~ 50)
32
e-MPS
Job
- Configuration
6
Press [Close] and returns to the Configuration screen.
7
Press [Close] and returns to the e-MPS screen.
Maximum Space Assigned to Temporary Code Jobs
This changes the hard disk space that holds temporary code jobs. You can change the
maximum space from 0 to 9999 (megabytes). The actual maximum size depends on the
size of free hard disk space.
2-44
1
Press the [Print] key. The machine enters the printer mode.
2
Press [e-MPS].
3
Press [Configuration].
Selecting the Printer Settings
4
Press S or T to select Temporary
Code JOB Size and press [Change
#].
Configuration
Setting Item
Value
Quick Copy
Temporary Code JOB Size
Permanent Code JOB Size
VMB Size
32
200MB
100MB
100MB
Change #
e-MPS
5
Press [+] or [-] or use the numeric
keys to enter the maximum size.
Back
Tempo. Code Job Size
Able to adjust Max HDD size of code job.
(0 ~ 9999)
200
e-MPS
MB
- Configuration
6
Press [Close] and returns to the Configuration screen.
7
Press [Close] and returns to the e-MPS screen.
Maximum Space Assigned to Permanent Code Jobs
This changes the hard disk space that holds permanent code jobs. You can change the
maximum space from 0 to 9999 (megabytes). The actual maximum size depends on the
size of free hard disk space. The operations are the same as Maximum Space Assigned to
Temporary Code Jobs.
Maximum Space Assigned to Virtual Mailboxes (VMB)
This changes the hard disk space for virtual mailboxes. You can change the maximum
space from 0 to 9999 (megabytes). The actual maximum size depends on the size of free
hard disk space. The operations are the same as Maximum Space Assigned to Temporary
Code Jobs.
2-45
Selecting the Printer Settings
Other Modes
The following modes can be accessed in the Others submenu:
•
Automatic Form Feed Timeout Setting
•
Resource Protect Mode
•
Auto Error Clear Setting
•
Finishing Error Detection
•
Printing the Service Status Page
•
Restart
•
Received Data Dump
Automatic Form Feed Timeout Setting
If this machine does not receive any information indicating the end of data after receiving
the last data, the machine waits for a certain time without printing the last page. When the
preset time elapses, the machine automatically performs a form feed. If you set the time to
0, the machine does not perform a form feed until GO is manually selected.
1
Press the [Print] key. The machine enters the printer mode.
2
Press [Printer Menu].
3
Press [Others].
tem.
Close
Paper
Handling
Font
Others
Page Set
Print
Quality
4
Press S or T to select Form Feed
Time Out and press [Change #].
RAM DISK
Mode
Others
Setting Item
Form Feed Time Out
Resource Protect
Auto Continue
Finishing Error
Value
30 Sec.
Permanent
Off
Change #
Service
Printer menu
5
Press [+] or [-] or use the numeric
keys to enter the form feed time.
Back
Form Feed Time Out
(0 ~ 495)
The timeout time can be between 0
and 495 seconds, in 5-second
increments.
30
(5)
(5)
Printer menu - Others
2-46
Seconds
Selecting the Printer Settings
6
Press [Close] and returns to the Others screen.
7
Press [Close] and returns to the Printer menu screen.
Resource Protect Mode
The Resource Protect Mode protects the resource data such as downloaded fonts and
macros and memorizes the PCL resources even if the emulation mode is switched Off. If
you select Permanent, temporary resources are not protected. If you select Permanent/
Temporary, temporary resources are protected.
1
Access Others, refer to Automatic Form Feed Timeout Setting on page 2-46.
2
Press S or T to select Resource
Protect and press [Change #].
Others
Setting Item
Form Feed Time Out
Resource Protect
Auto Continue
Finishing Error
Value
30 Sec.
Permanent
Off
Change #
Service
Printer menu
3
Press [Off], [Permanent], or [Permanent/Temporary].
4
Press [Close] and returns to the Others screen.
5
Press [Close] and returns to the Printer menu screen.
Auto Error Clear Setting
If an error that still allows you to continue printing occurs, the next received data is
automatically printed after a set period of time elapses. For example, if the printer is shared
over a network as a network printer and one person causes one of the above errors, after
the set period of time elapses, the data sent from the next person is printed. The default
setting is Off (Auto Error Clear disabled). The auto clear errors are:
•
Print overrun Press GO.
•
Memory overflow Press GO.
You can also set the time that elapses before Auto Continue is activated.
1
Access Others, refer to Automatic Form Feed Timeout Setting on page 2-46.
2-47
Selecting the Printer Settings
2
Press S or T to select Auto
Continue and press [Change #].
Others
Setting Item
Value
Form Feed Time Out
Resource Protect
Auto Continue
Finishing Error
30 Sec.
Permanent
Off
Change #
Service
Printer menu
3
Press [On] or [Off].
Back
Auto continue
When error occurs, auto timing for processing can be set.
When you have selected On, press
[+] or [-] or use the numeric keys to
enter the auto continue time.
The auto continue time can be
between 0 and 495 seconds, in 5second increments.
(0 ~ 495)
30
Seconds
Off
(5)
On
(5)
Printer menu - Others
4
Press [Close] and returns to the Others screen.
5
Press [Close] and returns to the Printer menu screen.
Finishing Error Detection
If the error detection setting for duplex (staple) printing has been turned On, and you
attempt to print onto a paper size and paper type that cannot be used for duplex (staple)
printing, the error message will be displayed and printing will stop. To print onto one-side
(without staple) of the paper only when this message is displayed, press [GO]. The default
setting is Off.
Mode
Description
Proces. Duplex On
print
Staple Mode
1
2-48
Displays an error message.
Press [GO] to continue single side printing. Press [Cancel] to
cancel printing.
Off
Continues 1-sided printing without showing an error message.
On
Displays an error message.
Press [GO] to clear the error message and continue printing
without stapling. Press [Cancel] to cancel printing.
Off
No error message is shown and printing continues without
stapling.
Access Others, refer to Automatic Form Feed Timeout Setting on page 2-46.
Selecting the Printer Settings
2
Press S or T to select Finishing
Error and press [Change #].
Others
Setting Item
Form Feed Time Out
Resource Protect
Auto Continue
Finishing Error
Value
30 Sec.
Permanent
Off
Change #
Service
Printer menu
3
Press S or T to select Proces.
Duplex print and press [Change #].
Finishing Error
Setting Item
Proces. Duplex print
On
Value
Staple Mode
On
Change #
Printer menu - Others
4
Press [On] or [Off].
5
Press [Close] and returns to the Finishing Error screen.
6
Repeat steps 3 to 5 to set the Staple Mode.
7
Press [Close] and returns to the Others screen.
8
Press [Close] and returns to the Printer menu screen.
Printing the Service Status Page
The service status page contains printer settings information that is more detailed than the
standard status page and is therefore mostly for service purposes. However, there is a
great deal of information on the service status page that may be useful to you.
1
Access Others, refer to Automatic Form Feed Timeout Setting on page 2-46.
2
Press [Service].
Others
Setting Item
Form Feed Time Out
Resource Protect
Auto Continue
Finishing Error
Value
30 Sec.
Permanent
Off
Change #
Service
Printer menu
2-49
Selecting the Printer Settings
3
Press [Print Status Page].
Service
Print Status Page
Paper Feed
Printer menu - Others
4
Press [Printing].
The message Processing data appears and the machine prints a service status page or
test page.
5
After the service status page is printed, the display returns to the Printer menu screen.
Restart
To reset only the printer board without the need to turn off to the machine, perform the
following procedure. All of the printing data and waiting data are deleted when this machine
is restarted.
1
Access Others, refer to Automatic Form Feed Timeout Setting on page 2-46.
2
Press [Printer Reset].
Only printer board is working without
turning off the main SW. Are you
sure? is displayed.
Close
Item
e Out
ect
Value
30 Sec.
Permanent
Off
Printer
Reset
Change #
3
Service
Print
HEX-DUMP
Press [Yes].
Restart is executed.
Received Data Dump
You can print data received by the printer as hexadecimal code for debugging programs
and files.
1
2-50
Access Others, refer to Automatic Form Feed Timeout Setting on page 2-46.
Selecting the Printer Settings
2
Press [Print HEX-DUMP].
Printing mode with dump Rx data.
Are you sure? is displayed.
Close
Item
Value
e Out
ect
30Sec.
Permanent
Off
Printer
Reset
Change #
3
Service
Print
HEX-DUMP
Press [Yes].
The message Processing data appears for a second, followed by Waiting.
4
While the message display is indicating Waiting send data to be hex-dumped to the printer.
The message display indicates Processing data while the data is being received.
NOTE: You can cancel printing of any more dump data by pressing [GO] and then
[CANCEL].
5
Once all data has been received, the message Waiting will appear. Press [GO] to finish
hex-dump printing.
2-51
Selecting the Printer Settings
2-52
3 Troubleshooting
Basic troubleshooting chart
If you experience trouble while you are using this machine as a printer, refer to the table
below to perform minor adjustments. If trouble persists, contact your service representative
or an authorized service center.
NOTE: For information in regard to general mechanical trouble with the machine, refer to
the Operation Guide for your copier.
Problem
Nothing is printed out
Check point
Is the power cord loose?
Procedure
Connect the power cord securely to a power
source.
Is the power on to the printer? Turn the main switch to the printer on.
Is the printer cable appropriate Be sure to use a compliant printer cable and
and is it connected properly? make sure it is connected properly.
Did you connect the printer
cable after you turned the
power to the printer On?
Connect the printer cable before you turn the
power to the printer on.
Is the printer off-line? (Is the
Status indicator flashing
amber?)
Perform the appropriate procedure to put the
printer on-line.
Press the [Print] key to switch to the printer
mode.
Press [GO].
The Status indicator will go out.
Text is not printed correctly Is the printer cable appropriate Be sure to use a compliant printer cable and
and is it connected properly? make sure it is connected properly.
Print out is not correct
Is the setting configuration in
your PC correct?
Confirm the settings in the printer driver as well
as in the software application in use.
Is the emulation protocol
setting correct?
Check the emulation protocol setting.
3-1
Troubleshooting
Display message
If an error message appears on the operation panel, first check the following tables for
cause of the trouble and then perform the corresponding procedure. For more detailed
information, refer to the Operation Guide for your copier as well as the Operation Guide for
any optional equipment that is installed in your machine.
Display message
Procedure
Add paper in drawer (cassette). The size or type of paper selected for printing does not match the size or
type of paper in the cassette. Replace the paper in the drawer with that of
## size (###)
the correct size and type.
If you want to switch to and print from a different cassette, select the desired
cassette on the touch panel and then press [GO].
The following commands will be displayed in the printer mode.
[GO]: Force-prints onto the current size or type of paper.
[Cancel]: Cancels the printing operation completely.
Use alternative? Press GO.
Displayed after changing the drawer. Press [GO].
Set paper Press GO.
This mode feeds a stack of multiple sheets one at a time. Every time you
want to feed a sheet, press [GO].
Load paper.
The cassette has run out of paper. Add paper.
Add staples.
The finisher (option) has run out of staples. Refer to the Operation Guide for
the finisher and replenish the staples.
Call service.
Trouble has occurred within the printer. Contact your service representative
or an authorized service center.
Account ID mismatch.
The account code you entered does not match the registered one. Check
the account code that is registered in the printer driver.
Exceeded print quantity limit.
The amount of printing accomplished has exceeded the acceptable capacity
as set under copy management. In order to print further, change the copy
management setting in the printer.
Error has occur. PLS change to This message will appear when a printer error occurs and the machine is in
printer screen and check.
a mode other than the printer mode. Press the [Print] key to switch to the
print mode screen and the corresponding error message will be displayed.
Memory card error Press GO.
Code: ##
A memory card error has occurred. Look at the error code given in place of
## and refer to Memory Card Errors on page 3-4. To ignore the memory
card error, press [GO].
HARD DISK error Press GO.
Code: ##
A hard disk error has occurred. Look at the error code given in place of ##
and refer to Hard Disk Errors on page 3-5. To ignore the hard disk error,
press [GO].
KPDL error Press GO.
Code: ##
The current print job cannot continue. Press [GO] prints out the data that
has already been processed. If auto recovery time has been set, printing will
resume automatically when the set time elapses. A KPDL error report can
be printed out from the Printer Menu.
For more information, refer to KPDL Error Printing on page 2-11 and
Automatic Form Feed Timeout Setting on page 2-46.
Memory Card error Insert
again.
The Memory Card (CompactFlash) was removed during operation under the
menu for printer-related settings. Reinsert the Memory Card.
Be sure to turn the main switch off before inserting the Memory Card.
3-2
Troubleshooting
Display message
Procedure
Insert the same memory card.
The Memory Card (CompactFlash) could not be detected during an
operation in which the printer was reading data from that card. Reinsert the
Memory Card.
Be sure to turn the main switch off before inserting the Memory Card.
Format error Memory card.
Initialization of the Memory Card (CompactFlash) currently inserted is
necessary.
Incollect slot. Please re-install.
The optional interface board is loaded in the wrong slot. Turn power off and
load the board in the correct slot.
File not found Press GO.
File error. Press [GO].
Read fonts: Failed
The printer failed to read the font data. Try to read the font data again.
Read macro: Failed
The printer failed to read the macro. Try to read the macro again.
Warning low memory.
There is not enough memory. You can check how much printer memory
there is by printing out a status page. Delete any unnecessary font data and
macros.
Warning image adapt.
Because there is not enough memory, printing cannot be performed at the
set resolution. Either add more memory to the printer or change the
resolution.
Print overrun Press GO.
A data overrun error has occurred due to insufficient memory.
Press the [Print] key to switch to the printer mode. Following commands will
be displayed.
[GO]: Continues printing.
[Cancel]: Cancels the printing operation completely.
If auto recovery time has been set, printing will resume automatically when
the set time elapses.
Once this error message is displayed, Page protect mode will be turned On
automatically.
Memory overflow Press GO.
The current print job could not be completed due to insufficient memory in
the printer.
Press the [Print] key to switch to the printer mode. Following commands will
be displayed.
[GO]: Continues printing. The data that has already been processed will be
printed out and the remaining portion of the print job will be printed onto the
following page.
[Cancel]: Cancels the printing operation completely.
If this error occurs often, it is recommended that you install additional
memory into the printer. For more detailed information on adding memory,
contact your service representative or an authorized service center.
If auto recovery time has been set, printing will resume automatically when
the set time elapses.
Virtual mailbox full.
There is not enough area in the virtual mailbox. Print out data in the virtual
mailbox.
Interface occupied.
The selected interface is currently is use. Wait for a while and then attempt
the operation again.
Format error Hard Disk.
Initialize the hard disk.
3-3
Troubleshooting
Storage Error Codes
RAM Disk Errors
Check the error code displayed in place of ## and refer to the following.
Code
Meaning
01
Format error. Turn power off and on again.
02
The RAM disk mode is off. Turn it on.
03
A write error has occurred. Turn off write protection.
04
The RAM disk does not have enough area to store the data. Delete any
unnecessary data to make more room.
05
The selected file could not be found. Check the file name and whether it is
on the RAM disk or not.
06
There is not enough system memory. Increase memory capacity.
98
Some of the data being collated was not read. Job data is corrupt.
Memory Card Errors
Check the error code displayed in place of ## and refer to the following.
Code
3-4
Meaning
01
Format error. Reformat the memory card.
02
Memory card load error. Correctly load the memory card.
03
A write error has occurred. Turn off write protection.
04
The memory card does not have enough area to store the data. Delete any
unnecessary data to make more room.
05
The selected file could not be found. Check the file name and whether it is
on the memory card or not.
Troubleshooting
Hard Disk Errors
Check the error code displayed in place of ## and refer to the following.
Code
Meaning
01
Format error. Reformat the hard disk.
02
Hard disk load error. Correctly load the hard disk.
03
A write error has occurred. Turn off write protection.
04
The hard disk does not have enough area to store the data. Delete any
unnecessary data to make more room.
05
The selected file could not be found. Check the file name and whether it is
on the hard disk or not.
06
There is not enough system memory. Increase memory capacity.
20
The hard disk is loaded in the wrong slot. Load the hard disk in the correct
slot.
85
An illegal name has been used for the virtual tray. Rename the tray
correctly.
86
The wrong password was used for the virtual mailbox. Input the correct
password.
88
Some of the data in the virtual mailbox was not read. Job data is corrupt.
97
No more jobs can be saved. The limit has been reached. Increase the
number of storable jobs and available area.
98
Some of the data in the job was not read. Job data is corrupt.
3-5
Troubleshooting
Pausing Printing
Toggle the printer’s on-line and off-line states. You can temporarily stop the print job by
switching the printer off-line, perform the following procedure.
1
Press the [Print] key. The machine enters the
printer mode.
2
Press [GO]. The message Off line is to print.
displayed and changes off-line.
Cancel
GO
NOTE: In off-line state, the printer can receive data, but cannot print.
3
3-6
To resume processing of the prints, press [GO] again. The message of Off line goes out,
returns to the on-line.
Troubleshooting
Canceling Printing
To cancel printing and clear the data, perform the following procedure.
1
Press the [Print] key. The machine enters the
printer mode.
2
Press [Cancel].
user1
Orig. Page
16
Letter
Cancel
User name: user1
3
Select the interface through which
printing to be canceled is performed.
Job name:
Stop
Select interface to cancel the job.
Current
Job
Network
Option
USB
NOTE: To stop canceling printing, press [Stop].
4
Printing is canceled.
3-7
Troubleshooting
Restart
To reset only the printer board without the need to turn off to the machine, perform the
following procedure. All of the printing data and waiting data are deleted when this machine
is restarted.
1
Press the [Print] key. The machine enters the
printer mode.
2
Press [Printer Menu].
Ready to print.
e-MPS
Printer
Menu
3
Press [Others].
Cancel
tem.
Close
Font
Paper
Handling
Others
Page Set
Print
Quality
4
RAM DISK
Mode
Press [Printer Reset].
Only printer board is working without
turning off the main SW. Are you
sure? is displayed.
Close
Item
e Out
ect
Value
30 Sec.
Permanent
Off
Printer
Reset
Change #
5
Press [Yes].
Restart is executed.
3-8
Service
Print
HEX-DUMP
4 Options
This machine has the following options available to satisfy your printing requirements.
Additional Memory
To expand the printer memory for more complex print jobs and faster print speed, you can
plug in optional memory modules (dual in line memory modules) in two memory slots
provided on the printer main controller board. You can select additional memory modules
from 64, 128, or 256MB. The maximum memory size is 512MB (256MB x 2).
Hard Disk (HD-5)
The hard disk is used for saving print data. This is advantageous when printing multiple
sets of copies, as high-speed printing is possible using the electronic sorting function. The
hard disk is further required in order to use the e-MPS function.
Memory Card
The printer is equipped with a slot for a memory card with the maximum size of 256MB. A
memory card is useful for storing fonts, macros, and overlays.
Network Interface Card (IB-21E/IB-23)
Along with the standard for the network interface on the printer, the network interface card
supports TCP/IP, IPX/SPX, NetBEUI and AppleTalk protocols, so that the printer can be
used on network environments including Windows, Macintosh, UNIX, NetWare, etc. The
network interface card must be installed in the option interface slot.
4-1
Options
4-2
5 Specifications
NOTE: Specifications are subject to change without notice.
Item
Specification
Printing speed (A4/Letter)
KM-2540: 25 pages/minute
KM-3040: 30 pages/minute
Resolution
Fast1200 mode, 600 dpi, 300 dpi
Controller
Power PC 750CXr 400MHz
Main memory
Standard: 64 MB
Maximum: 576 MB
Additional memory
64 MB, 128 MB, and 256 MB (2 slots)
Compatible Operating
Systems
Microsoft Windows 2000/XP/Vista
Microsoft Windows Server 2003
Apple Macintosh OS 9
Apple Macintosh OS X
Interfaces
- USB
Hi-speed USB, 1 port
- Ethernet
Protocol support: TCP/IP, IPX/SPX, NetBEUI,
AppleTalk, 1 port
- Option
Network interface card, 1 port
Memory card slot
1 slot (CompactFlash card)
Hard disk slot
1 slot
Installed Fonts
PCL: 80
KPDL: 136
Bitmap: 1
5-1
Specifications
5-2
A1
Rev. 1.0 2007.7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement