Mercury HQJF578 Crystal Oscillator Owner manual

Mercury HQJF578 Crystal Oscillator Owner manual
H_JF578 Series
150 fsec typical Phase Jitter
High Frequency Ultra-low Jitter Crystal Oscillators
MERCURY
Since 1973
H_JF578 series(7.0x5.0x1.8 mm, 8 pads), a member of Mercury QuikXO™ quick-turn
clock oscillators, features LVPECL, LVDS, CML or HCSL output logics and
fento-second (fsec) RMS phase jitter (129 fsec for LVPECL 644.530 MHz at 3.3V).
Short lead time, for both standard and custom frequencies.
Other QuikXO™ products in this family: G_JF578 series(VCXOs).
General Specifications(*): at Ta=+25°C
Output Logic Type
LVPECL
LVDS
CML
HCSL
Frequency Range
150 ~ 2100 MHz
150 ~ 2100 MHz
15 ~ 2100 MHz
150 ~ 700 MHz
50 ohms into VDD-2V or
Thevenin equivalent
100 ohms between
OUT and OUTN
50 ohms to VDD
50 ohms to GND
+1.8V ± 5%
+2.5V ± 10%
+3.3V ± 10%
Load
+2.5V ± 10%
+3.3V ± 10%
+2.5V ± 10%
+3.3V ± 10%
+1.8V ± 5%
+2.5V ± 10%
+3.3V ± 10%
Output “High” Voltage; VOH
VDD - 1.165V min.
VDD - 0.8V max.
VDD : 1.4 V typical
VDD : 1.6 V max.
VDD – 0.085V min
VDD = max.
VDD : 0.66V min.
VDD : 1.15V max.
Output “Low” Voltage; VOL
VDD – 2.0V min.
VDD - 1.55V max
VDD : 1.1 V typical
VDD : 0.9 V min.
VDD - 0.6V min.
VDD - 0.32V min.
VDD : 0.0V min.
VDD : 0.15V max.
Power Supply Voltage (VDD)
Frequency stability over
operating temp. range
Frequency Stability Codes
± 25 ppm
± 50 ppm
± 100 ppm
Commercial (-10 to +70°C)
A
B
C
Industrial (-40 to +85°C)
D
E
F
if non-standard , please enter
the desired stability after the
“C” or “I” for example :
“C20” ± 20ppm over
-10 to +70°C
Aging at Ta = 25˚C
+3ppm max. first year ; ±2ppm max. per year thereafter
Duty Cycle (at 50% VDD)
50% ±5%
50% ±5%
50% ±5%
50% ±5%
Rise Time (Tr) /
Fall Time (Tf)
(20% ↔ 80% waveform )
0.35 nS. max.
0.35 nS. max.
0.35 nS. max.
0.4 nS. max.
Current Consumption
at VDD = 3.3V
100mA typ.
120mA max.
75mA typ.
90mA max.
70mA typ.
85mA max.
94mA typ.
115mA max.
Current with Output
Disabled
99mA typ.
74mA typ.
69mA typ.
93mA typ.
Start-up Time
5ms typical ; 10 ms max.
Phase Jitter, rms
(12 KHz to 20 MHz)
150 fsec typical , 300 fsec Max.
MERCURY
Page 1 of 6
July 16, 2018
Revision A.4
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com
H_JF578 Series
150 fsec typical Phase Jitter
High Frequency Ultra-low Jitter Crystal Oscillators
MERCURY
Since 1973
Output Enable Function on Pad 1
0.8% of VDD minimum to enable output.
OE Control
0.2% of VDD maximum to disable output.
Output Enable Time
2.5 ms max.
Output Disable Time
10 us max.
(*)If you want detailed specifications, please call for details.
Environmental Performance Specifications
Second Level Interconnect
RoHS compliant, Pb (lead) free in accordance with EU Directive 2002/95/EC
6/6 (2002/95/EC) and WEEE (2002/96/EC).
Free of halide, cadmium, hexavalent chromium, lead, mercury, PBB’s and PBDE’s.
e4
Moisture Sensitivity Level
Level 1 (infinite) according to IPC/JEDEC J-STD-020D.1
Storage temp. range
-55 to +150°C
Humidity
85% RH, 85°C, 48 hours
Fine Leak / Gross Leak
MIL-Std-883, method 1014, condition A / MIL-Std-883, method 1014, condition C
Solderability
MIL-STD-202F method 208E
Reflow
260°C for 10 sec. Two times.
Vibration
MIL-STD-202F method 204, 35G, 50 to 2000 Hz
Shock
MIL-STD-202F method 213B, test condi. E, 1000GG ½ sine wave
Resistance to Solvent
MIL-STD-202, method 215
Temperature Cycling
MIL-STD-883, method 1010
ESD Rating
Pad Surface Finish
Human body model (HBM): 2000 V min.
Gold (0.3 um to 1.0 um) over nickel (1.27 um to 8.89 um)
Weight of the Device
0.045 grams typical
Green Requirement
Part Number Format and Example:
Example: 3HPJF5781-E-644.530
3
Supply Voltage
code
“3” for 3.3V
“25” for 2.5V
“18” for 1.8V
H
“H” : for
Crystal
oscillators
P
Output Logic Code
“P” : PECL
“D” : LVDS
“C” : HCSL
“Q” : CML
JF578
“JF”: Product Series.
“578”: Package size
7.0x5.0x1.8 mm
8 Pad
-
1
OE function.
“1”: OE on
pad1. Note 1
-
E
Frequency stability
code:
“A”~“F”.
See table above.
-
644.530
Frequency(MHz)
Note 1: OE on pad 2 and pad 1 no connection is also available. Please change product series from “JF5381” to “JF5382”.
MERCURY
Page 2 of 6
July 16, 2018
Revision A.4
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com
H_JF578 Series
150 fsec typical Phase Jitter
High Frequency Ultra-low Jitter Crystal Oscillators
MERCURY
Since 1973
Output OE Function on Pad1
3HPJF5781 Phase Noise and Phase Jitter Data (typical), VDD=+3.3V, Voltage Control = Ground
Frequency (MHz)
SSB Phase
Noise Data
(dBc/Hz
Typical)
156.250
491.52
644.530
1480
2100
10 Hz offset
-39
-16
-31
-12
-18
100 Hz offset
-74
-48
-58
-54
-49
1 KHz offset
-99
-83
-86
-80
-77
10 KHz offset
-123
-112
-110
-104
-100
100 KHz offset
-139
-128
-126
-119
-116
1 MHz offset
-149
-140
-137
-130
-125
5 MHz offset
-156
-151
-150
-145
-141
10 MHz offset
-157
-153
-153
-148
-145
20 MHz offset
-157
-154
-153
-150
-147
159
155
151
147
163
Phase Jitter fsec
(12KHz ~ 20 MHz, RMS)
MERCURY
Page 3 of 6
July 16, 2018
Revision A.4
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com
H_JF578 Series
150 fsec typical Phase Jitter
High Frequency Ultra-low Jitter Crystal Oscillators
MERCURY
Since 1973
Phase Noise Plot of 3HPJF5781-E-644.530 MHz, VDD=+3.3V, LVPECL, Output Enable =+3.3V, +25°C.
Package Dimensions and Recommended Solder Pad Layout
unit: (mm)
MERCURY
Page 4 of 6
July 16, 2018
Revision A.4
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com
H_JF578 Series
150 fsec typical Phase Jitter
High Frequency Ultra-low Jitter Crystal Oscillators
Test Circuits and Output Waveforms
LVPECL
LVDS
HCSL
CML
Differential Output Waveforms
Duty cycle=
∗ 100%.
MERCURY
Since 1973
Measured at 50% VDD
MERCURY
Page 5 of 6
July 16, 2018
Revision A.4
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com
H_JF578 Series
150 fsec typical Phase Jitter
High Frequency Ultra-low Jitter Crystal Oscillators
MERCURY
Since 1973
Recommended Solder Reflow Profile (per IPC/JEDEC J-STD-020D.1)
Tp
Tsmax
Te
m
pe
rat
ur
e
TL
tp
Max. Ramp Up Rate=3°C/s
Max. Ramp Down Rate=6°C/s
Tc-5°C
User Tp≤Tc
tL
Preheat Area
Tsmin
Tc
Tc-5°C
User tp
ts
25
Time 25°C to Peak
Time
Profile Feature
Sn-Pb Eutectic Assembly
Pb-free Assembly
100⁰C
150⁰C
60 to 120 seconds
3⁰C / sec. max.
150⁰C
200⁰C
60 to 180 seconds
3⁰C / sec. max.
Peak package body temperature (Tp)
183⁰C
60 to 150 seconds
235⁰C
217⁰C
60 to 150 seconds
260⁰C
Time (Tp) within 5⁰C of the classification temperature Tc
10 to 30 seconds
20 to 40 seconds
Ramp-down rate (Tp to TL)
6⁰C / second max.
6⁰C / second max.
Preheat/Soak
Temperature min. (Ts min.)
Temperature max. (Ts max.)
Time (ts) (Ts min. to Ts max.)
Ramp-up rate (TL to Tp)
Liquidous temperature (TL )
Time (tL) maintained above TL
Time 25⁰C to peak temperature
6 minutes max.
All temperatures refer to topside of the package, measured on the package body surface.
8 minutes max.
MERCURY
Page 6 of 6
July 16, 2018
Revision A.4
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement