REPOTEC RP-IMC801FP Industrial Media Converter Owner Manual

Add to my manuals
6 Pages

advertisement

REPOTEC RP-IMC801FP Industrial Media Converter Owner Manual | Manualzz

User Manual

Industrial Gigabit Media Converter

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received; including interference that may cause undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE, the essential protection requirement of

Council Directive 2004/108/EC on the approximation of the laws of the Member

States relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

Edition 2.0

Copyright © 2017, All Rights Reserved.

1

Key Features

 Rugged design Aluminum enclosure 103.5x32x81.5mm (LxWxD)

 Supports 18V-36VAC/12V-56VDC

 Supports Link Fault Pass through (LFP) function

 Supports Switch Mode and Converter Mode.

 Support SFP fiber speed 100M or 1000M dual mode

 Surge protection diodes on power input.

 ESD protection diodes on RJ-45 port

 Provides Far End Fault function on FX port.

 Provides increased Noise Immunity

 Working in extreme environment -40°C to 75°C

Introduction

This mini, hardened Industrial Gigabit Media Converter is designed for Security,

Transportation and Telco applications to extend your network distances. It can be powered by wide range of VAC or VDC. With its multi-purpose design, it can also be used for Din-Rail or Wall-Mounted. It is an ideal unit for IP surveillance, traffic monitoring and Security applications in critical environment. It can tolerate -40°C to 75°C in harsh environment to perform a reliable network.

Installation package

The following items are shipped with this device:

 Din-Rail Mounted * 1

 Wall-Mounted * 2

 Screws * 4

 4 pin Terminal Block * 1

2

Power connection

This unit provides 4 pin terminal block. It can be operated using either VAC or VDC power source. The VDC power range is from 12VDC to 56VDC, and the VAC power range is from 18VAC to 36VAC. Always Make sure your input voltage is within this supported voltage range.

To make power connection – Follow the printed polarity for V1+, V1-, V2+, V2- and Ground. Connect positive wire to V+, connect negative wire to V- and also connect neutral wire to ground.

+V1- +V2-

Connecting procedure:

STEP 1 –

Take out 4 pin terminal block located in the included mounting kit package

STEP 2 –

Connect power wire to 4 pin terminal block. V1+, V1- or redundant power wire to

V2+, V2- and Ground

STEP 3 –

Plug into terminal block socket shown above. Polarity needs to match the V+ and

V-.

WARNING -- Always SHUTS OFF power source to connect power wire.

WARNING -- Any exceeded input voltage will not make this unit function and may damage this unit.

3

Dip switch function

This unit is equipped with 4 pin Dip-Switch located on the front panel. Adjust the

Dip-Switch setting will change the default function of this unit. All the Dip-Switch settings are set to manufacturer default as OFF

Table shown as below is the features of these Dip-Switch function. You may change the Dip-Switch setting to your desired environment.

10

00

1

100

Au to

S

W

OF

F

OFF Con LFP

LED indicator

LED Color

DIP 1

DIP 2

DIP 3

DIP 4

ON SFP Speed 100M

OFF SFP Speed 1000M (Default)

ON Set SFP Auto-negotiation disable

OFF Set SFP Auto-negotiation enable (Default)

ON Converter Mode

OFF Switch Mode (Default)

ON LFP function turn on

OFF LFP function turn off (Default)

PW1

PW2

Green

Green

SFP LNK/ACT Green

1000

10/100

Green

Amber

State

ON

OFF

ON

Description

Power is detected

Power is not detected

Power is detected

OFF

ON

Power is not detected

FX port is detected

Flashing FX data is transmitting/receiving

ON 1000M speed is detected

Flashing TX data is transmitting/receiving

ON 100M speed is detected

Flashing TX data is transmitting/receiving

4

Specification

IEEE Standard

Data Processing

Flow Control

Packet Buffer Size

Jumbo Frame

Network Connector

LED Indicators

DIP Switch Function

Power Protection

Power Input

Power Consumption

Removable Terminal

Block

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE 802.3ab 1000Base-T Gigabit Ethernet

IEEE 802.3z 1000Base-X Gigabit Ethernet

Store and Forward

IEEE 802.3x Flow Control and Back Pressure

1M

9KB

1 x RJ-45 10/100/1000 Base-T(X)

Auto MDI/MDI-X function, Full/Half duplex

1 x 100/1000 BaseF(X) SFP

PW1 (Green): ON

Power is detected

OFF

Power is not detected

PW2 (Green): ON

Power is detected

OFF

Power is not detected

SFP LNK/ACT (Green): ON

FX port is detected

Flashing

FX data is transmitting/receiving

1000 (Green): ON

1000M speed is detected

Flashing

TX data is transmitting/receiving

10/100 (Amber): ON

10/100M speed is detected

Flashing

TX data is transmitting/receiving

DIP 1: ON

SFP Speed 100M

OFF

SFP Speed 1000M (Default)

DIP 2: ON

Set SFP Auto-Negotiation disable

OFF

Set SFP Auto-Negotiation enable (Default)

DIP 3: ON

Converter Mode

OFF

Switch Mode (Default)

DIP 4: ON

LFP enable

OFF

LFP disable (Default)

Surge protection diodes on power input

Reverse polarity protection on power input

Overload current protection

Redundant Power, 18-36VAC, 12-56VDC

3Watts @48VDC full load

4 pin contact terminal block for power input

Wire range : 0.34mm^2 to 2.5mm^2

Solid wire (AWG) : 12-24/14-22

Stranded wire(AWG) : 12-24/14-22

Wire Strip length : 7-8mm

Torque : 5lb-In/0.5Nm/0.56Nm

5

Operating Temperature

Operating Humidity

Storage Temperature

Housing Design

-40°C~75°C

5% to 95% (Non-condensing)

-40°C~85°C

Case Dimension (L x W x D) 103.5 x 32 x 81.5 mm (L x W x D)

Installation

IP30 Design, Rugged Aluminum

DIN-Rail Mounted or Panel Mounted

Certifications

EN55022/24

EN55011

Safety

EMC/EMS

ITE equipment

Industrial, Scientific and Medical (ISM) equipment

IEC EN60950-1

CE, FCC, VCCI

EMI

FCC Part 15 Subpart B Class A,

CE EN 55022 Class A

EN 50155 / EN 60068-2-6 Vibration

EN 50155 / EN 60068-2-27 Shock

EN 50155 / EN 60068-2-32 Free Fall

Housing Dimension (mm)

6

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement