Allnet ALL-CAM2373-VEP User Guide

Allnet ALL-CAM2373-VEP User Guide
ALL-CAM2305-LW
ALL-CAM2306-C
ALL-CAM2373-VEP
ALL-CAM2386-LEFN
ALL-CAM2387-LEFN
ALL-CAM2388-LVE(W)
ALL-CAM2395(v2)-LVEF
ALL-CAM2396(v2)-LEF
ALL-CAM2397-LE(W)
User Manual
1
Default-IP
via DHCP
Username:
admin
Password:
Has to be configured at the first log
in.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the
limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the Low Voltage
Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to
your local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery
that cannot be disposed of as unsorted municipal waste in the
European Union. See the product documentation for specific
battery information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more
information see: www.recyclethis.info.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
3
Safety Instruction
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are
neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions
are neglected.
Warnings Follow these safeguards to Cautions Follow these precautions to
prevent serious injury or death.
prevent potential injury or material
damage.
Warnings:
 Please adopt the power adapter which can meet the safety extra low voltage
(SELV) standard. And source with 12 VDC according to the IEC60950-1 and
Limited Power Source standard.
 If the product does not work properly, please contact your dealer or the
nearest service center. Never attempt to disassemble the camera yourself. (We
shall not assume any responsibility for problems caused by unauthorized
repair or maintenance.)
 To reduce the risk of fire or electrical shock, do not expose this product to rain
or moisture.
 This installation should be made by a qualified service person and should
conform to all the local codes.
 Please install blackouts equipment into the power supply circuit for
convenient supply interruption.
 Please make sure that the ceiling can support more than 50(N) Newton
gravities if the camera is fixed to the ceiling.
 If the product does not work properly, please contact your dealer or the
nearest service center. Never attempt to disassemble the camera yourself. (We
shall not assume any responsibility for problems caused by unauthorized
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
4
repair or maintenance.)
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
5
Cautions:

Make sure the power supply voltage is correct before using the camera.

Do not drop the camera or subject it to physical shock.

Do not touch sensor modules with fingers. If cleaning is necessary, use a clean
cloth with a bit of ethanol and wipe it gently. If the camera will not be used
for an extended period of time, put on the lens cap to protect the sensor
from dirt.

Do not aim the camera lens at the strong light such as sun or incandescent
lamp. The strong light can cause fatal damage to the camera.

The sensor may be burned out by a laser beam, so when any laser equipment
is being used, make sure that the surface of the sensor not be exposed to the
laser beam.

Do not place the camera in extremely hot, cold temperatures, dusty or damp
environment, and do not expose it to high electromagnetic radiation.

To avoid heat accumulation, good ventilation is required for a proper
operating environment.

Keep the camera away from water and any liquid.

While shipping, the camera should be packed in its original packing.
Notes:
For the camera supports IR, you are required to pay attention to the following
precautions to prevent IR reflection:

Dust or grease on the dome cover will cause IR reflection. Please do not
remove the dome cover film until the installation is finished. If there is dust
or grease on the dome cover, clean the dome cover with clean soft cloth and
isopropyl alcohol.

Make certain the installation location does not have reflective surfaces of
objects too close to the camera. The IR light from the camera may reflect
back into the lens causing reflection.

The foam ring around the lens must be seated flush against the inner surface
of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to
camera body so that the foam ring and the dome cover are attached
seamlessly.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
6
Table of Contents
Chapter 1
System Requirement .................................................... 10
Chapter 2
Network Connection .................................................... 11
2.1
Setting the Network Camera over the LAN................................. 11
2.1.1
Wiring over the LAN......................................................................................... 11
2.1.2
Detecting and Changing the IP Address ......................................................... 12
2.2
Setting the Network Camera over the WAN ............................... 14
2.2.1
Static IP Connection.......................................................................................... 14
2.2.2
Dynamic IP Connection .................................................................................... 15
Chapter 3
Access to the Network Camera ................................... 18
3.1
Accessing by Web Browsers .......................................................... 18
3.2
Accessing by Client Software ....................................................... 20
Chapter 4
Wi-Fi Settings ................................................................ 23
4.1
Configuring Wi-Fi Connection in Manage and Ad-hoc Modes ... 23
4.2
Easy Wi-Fi Connection with WPS function ................................... 27
4.3
IP Property Settings for Wireless Network Connection ............. 30
Chapter 5
Live View ....................................................................... 32
5.1
Live View Page ............................................................................... 32
5.2
Starting Live View ......................................................................... 33
5.3
Recording and Capturing Pictures Manually ............................... 34
5.4
Operating PTZ Control ................................................................... 34
5.4.1
PTZ Control Panel ............................................................................................. 35
5.4.2
Setting / Calling a Preset .................................................................................. 36
5.4.3
Setting / Calling a Patrol .................................................................................. 37
Chapter 6
Network Camera Configuration .................................. 39
6.1
Configuring Local Parameters ...................................................... 39
6.2
Configuring Time Settings ............................................................ 41
6.3
Configuring Network Settings ..................................................... 43
6.3.1
Configuring TCP/IP Settings ............................................................................. 43
6.3.2
Configuring Port Settings ................................................................................ 45
6.3.3
Configuring PPPoE Settings ............................................................................. 46
6.3.4
Configuring DDNS Settings .............................................................................. 46
6.3.5
Configuring SNMP Settings ............................................................................. 49
6.3.6
Configuring 802.1X Settings ............................................................................ 51
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
7
6.3.7
Configuring QoS Settings ................................................................................ 52
6.3.8
Configuring UPnP™ Settings ........................................................................... 53
6.3.9
Email Sending Triggered by Alarm.................................................................. 53
6.3.10 Configuring NAT (Network Address Translation) Settings ............................ 55
6.3.11 Configuring FTP Settings.................................................................................. 56
6.3.12 HTTPS Settings .................................................................................................. 57
6.4
Configuring Video and Audio Settings ........................................ 59
6.4.1
Configuring Video Settings ............................................................................. 59
6.4.2
Configuring Audio Settings ............................................................................. 62
6.4.3
Configuring ROI Encoding ............................................................................... 62
6.4.4
Display Info. on Stream .................................................................................... 64
6.5
Configuring Image Parameters .................................................... 64
6.5.1
Configuring Display Settings ........................................................................... 64
6.5.2
Configuring OSD Settings ................................................................................ 70
6.5.3
Configuring Text Overlay Settings .................................................................. 71
6.5.4
Configuring Privacy Mask ................................................................................ 72
6.6
Configuring and Handling Alarms ............................................... 73
6.6.1
Configuring Motion Detection ........................................................................ 74
6.6.2
Configuring Video Tampering Alarm.............................................................. 80
6.6.3
Configuring Alarm Input.................................................................................. 81
6.6.4
Configuring Alarm Output .............................................................................. 83
6.6.5
Handling Exception .......................................................................................... 84
6.6.6
Configuring Line Crossing Detection .............................................................. 84
6.6.7
Configuring Intrusion Detection ..................................................................... 86
6.6.8
Configuring Other Alarm ...................... Fehler! Textmarke nicht definiert.
6.7
Configuring NAS Settings ............................................................. 89
6.8
Configuring Recording Schedule .................................................. 91
6.9
Configuring Snapshot Settings .................................................... 95
Chapter 7
Playback ........................................................................ 98
Chapter 8
Log Searching ............................................................. 101
Chapter 9
Others.......................................................................... 103
9.1
Managing User Accounts ............................................................ 103
9.2
Authentication ............................................................................. 105
9.3
Anonymous Visit ......................................................................... 106
9.4
IP Address Filter ........................................................................... 107
9.5
Security Service ........................................................................... 108
9.6
Viewing Device Information ....................................................... 109
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
8
9.7
Maintenance ................................................................................ 110
9.7.1
Rebooting the Camera ................................................................................... 110
9.7.2
Restoring Default Settings ............................................................................. 110
9.7.3
Exporting / Importing Configuration File ..................................................... 111
9.7.4
Upgrading the System .................................................................................... 112
9.8
RS-232 Settings ............................................................................ 112
9.9
RS-485 Settings ............................................................................ 113
9.10
Service Settings ........................................................................... 114
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
9
Chapter 1
System Requirement
Operating System: Microsoft Windows XP SP1 and above version / Vista /
Win7 / Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz to Core i7-4000 series or higher, depending
on different video resolutions
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 7.0 and above version, Safari 5.02 and
above version, Mozilla Firefox 3.5 and above version and Google Chrome8
and above versions.
10
Chapter 2
Network Connection
Before you start:

If you want to set the network camera via a LAN (Local Area Network),
please refer to Section 2.1 Setting the Network Camera over the
LAN.

If you want to set the network camera via a WAN (Wide Area
Network), please refer to Section 2.2 Setting the Network Camera
over the WAN.
2.1 Setting the Network Camera over the
LAN
Purpose:
To view and configure the camera via a LAN, you need to connect the
network camera in the same subnet with your computer, and install the
SADP or ALL-VMS software to search and change the IP of the network
camera.
Note: For the detailed introduction of SADP, please refer to Appendix 1.
2.1.1 Wiring over the LAN
The following figures show the two ways of cable connection of a
network camera and a computer:
11
Purpose:

To test the network camera, you can directly connect the network
camera to the computer with a network cable as shown in Figure 2-1.

Refer to the Figure 2-2 to set network camera over the LAN via a
switch or a router.
Figure 2-1 Connecting Directly
Figure 2-2 Connecting via a Switch or a Router
2.1.2 Detecting and Changing the IP Address
You need the IP address to visit the network camera.
Steps:
1. To get the IP address, you can choose either of the following methods:

Use SADP, a software tool which can automatically detect the
online network cameras in the LAN and list the device information
including IP address, subnet mask, port number, device serial
number, device version, etc., shown in Figure 2-3.

Use the ALL-VMS client software to list the online devices. Please
refer to the user manual of ALL-VMS client software for detailed
information.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
12
2. Change the IP address and subnet mask to the same subnet as that of
your computer.
3. Enter the IP address of network camera in the address field of the web
browser to view the live video.
Notes:

The default IP address is set to DHCP and if no DHCP-Server is active
you have to configure the ip-address via SADP-tool. The port number
is 8000. The default user name is admin, and the password has to be
configured at the first log in.

For accessing the network camera from different subnets, please set
the gateway for the network camera after you logged in. For detailed
information, please refer to Section 6.3.1 Configuring TCP/IP
Settings.
Figure 2-3 SADP Interface
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
13
2.2 Setting the Network Camera over the
WAN
Purpose:
This section explains how to connect the network camera to the WAN with
a static IP or a dynamic IP.
2.2.1 Static IP Connection
Before you start:
Please apply a static IP from an ISP (Internet Service Provider). With the
static IP address, you can connect the network camera via a router or
connect it to the WAN directly.

Connecting the network camera via a router
Steps:
1. Connect the network camera to the router.
2. Assign a LAN IP address, the subnet mask and the gateway. Refer to
Section 2.1.2 Detecting and Changing the IP Address for detailed IP
address configuration of the camera.
3. Save the static IP in the router.
4. Set port mapping, e.g., 80, 8000, and 554 ports. The steps for port
mapping vary according to the different routers. Please call the router
manufacturer for assistance with port mapping.
5. Visit the network camera through a web browser or the client software
over the internet.
Figure 2-4 Accessing the Camera through Router with Static IP
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
14

Connecting the network camera with static IP directly
You can also save the static IP in the camera and directly connect it to the
internet without using a router. Refer to Section 2.1.2 Detecting and
Changing the IP Address for detailed IP address configuration of the
camera.
Figure 2-5 Accessing the Camera with Static IP Directly
2.2.2 Dynamic IP Connection
Before you start:
Please apply a dynamic IP from an ISP. With the dynamic IP address, you
can connect the network camera to a modem or a router.

Connecting the network camera via a router
Steps:
1. Connect the network camera to the router.
2. In the camera, assign a LAN IP address, the subnet mask and the
gateway. Refer to Section 2.1.2 Detecting and Changing the IP
Address for detailed LAN configuration.
3. In the router, set the PPPoE user name, password and confirm the
password.
4. Set port mapping. E.g. 80, 8000, and 554 ports. The steps for port
mapping vary depending on different routers. Please call the router
manufacturer for assistance with port mapping.
5. Apply a domain name from a domain name provider.
6. Configure the DDNS settings in the setting interface of the router.
7. Visit the camera via the applied domain name.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
15

Connecting the network camera via a modem
Purpose:
This camera supports the PPPoE auto dial-up function. The camera gets a
public IP address by ADSL dial-up after the camera is connected to a
modem. You need to configure the PPPoE parameters of the network
camera. Refer to Section 5.3.3 Configuring PPPoE Settings for detailed
configuration.
Figure 2-6 Accessing the Camera with Dynamic IP
Note: The obtained IP address is dynamically assigned via PPPoE, so the IP
address always changes after rebooting the camera. To solve the
inconvenience of the dynamic IP, you need to get a domain name from the
DDNS provider (E.g. DynDns.com). Please follow the steps below for
normal domain name resolution and private domain name resolution to
solve the problem.

Normal Domain Name Resolution
Figure 2-7 Normal Domain Name Resolution
Steps:
1. Apply a domain name from a domain name provider.
2. Configure the DDNS settings in the DDNS Settings interface of the
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
16
network camera. Refer to Section 6.3.4 Configuring DDNS Settings
for detailed configuration.
3. Visit the camera via the applied domain name.

Private Domain Name Resolution
Figure 2-8 Private Domain Name Resolution
Steps:
1. Install and run the IP Server software in a computer with a static IP.
2. Access the network camera through the LAN with a web browser or
the client software.
3. Enable DDNS and select IP Server as the protocol type. Refer to Section
6.3.4 Configuring DDNS Settings for detailed configuration.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
17
Chapter 3
Access to the Network Camera
3.1 Accessing by Web Browsers
Steps:
1. Open the web browser.
2. Input the IP address of the network camera in the address bar and
press the Enter key to enter the login interface.
3. Now you have to configure a password first:
18
4. Input the user name and password and click Login.
Figure 3-1 Login Interface
Notes:
 Multi-language is supported. English, Simplified Chinese, Traditional
Chinese, Russian, Turkish, Japanese, Korean, Thai, Vietnamese,
Estonian, Bulgarian, Hungarian, Czech, Slovak, French, Italian, German,
Spanish, Portuguese, Polish, Greek, Dutch, Romanian, Finnish,
Norwegian, Danish, Swedish, Croatian, Serbian, Slovenian, etc.
5. Install the plug-in before viewing the live video and operating the
camera. Please follow the installation prompts to install the plug-in.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
19
Figure 3-2 Download and Install Plug-in
Figure 3-3 Install Plug-in (1)
Figure 3-4 Install Plug-in (2)
Note: You may have to close the web browser to install the plug-in. Please
reopen the web browser and log in again after installing the plug-in.
3.2 Accessing by Client Software
The product CD contains the ALL-VMS client software. You can view the
live video and manage the camera with the software.
Follow the installation prompts to install the software. The control panel
and live view interface of ALL-VMS client software are shown as bellow.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
20
Figure 3-5 ALL-VMS Control Panel
Figure 3-6 ALL-VMS Configuration Panel
Note: For detailed information about the software, please refer to the
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
21
user manual of the ALL-VMS.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
22
Chapter 4
Wi-Fi Settings
Purpose:
By connecting to the wireless network, you don’t need to use cable of any
kind for network connection, which is very convenient for the actual
surveillance application.
Note: This chapter is only applicable for the cameras with the built-in
Wi-Fi module.
4.1 Configuring Wi-Fi Connection in Manage
and Ad-hoc Modes
Before you start:
A wireless network must be configured.
Wireless Connection in Manage Mode
Steps:
1. Enter the Wi-Fi configuration interface.
Configuration> Advanced Configuration> Network> Wi-Fi
Figure 4-1 Wireless Network List
2. Click Search to search the online wireless connections.
3. Click to choose a wireless connection on the list.
23
Figure 4-2 Wi-Fi Setting- Manage Mode
4. Check the checkbox to select the Network mode as Manage, and
the Security mode of the network is automatically shown when you
select the wireless network, please don’t change it manually.
Note: These parameters are exactly identical with those of the router.
5. Enter the key to connect the wireless network. The key should be
that of the wireless network connection you set on the router.
Wireless Connection in Ad-hoc Mode
If you choose the Ad-hoc mode, you don’t need to connect the wireless
camera via a router. The scenario is the same as you connect the camera
and the PC directly with a network cable.
Steps:
1. Choose Ad-hoc mode.
Figure 4-3 Wi-Fi Setting- Ad-hoc
2. Customize a SSID for the camera.
3. Choose the Security Mode of the wireless connection.
Figure 4-4 Security Mode- Ad-hoc Mode
4. Enable the wireless connection function for your PC.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
24
5. On the PC side, search the network and you can see the SSID of the
camera listed.
Figure 4-5 Ad-hoc Connection Point
6. Choose the SSID and connect.
Security Mode Description:
Figure 4-6 Security Mode
You can choose the Security Mode as not-encrypted, WEP,
WPA-personal, WPA-enterprise, WPA2-personal, and WPA2-enterprise.
WEP mode:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
25
Figure 4-7 WEP Mode

Authentication - Select Open or Shared Key System Authentication,
depending on the method used by your access point. Not all access
points have this option, in which case they probably use Open System,
which is sometimes known as SSID Authentication.

Key length - This sets the length of the key used for the wireless
encryption, 64 or 128 bit. The encryption key length can sometimes be
shown as 40/64 and 104/128.

Key type - The key types available depend on the access point being
used. The following options are available:
HEX - Allows you to manually enter the hex key.
ASCII - In this method the string must be exactly 5 characters for
64-bit WEP and 13 characters for 128-bit WEP.
WPA-personal and WPA2-personal Mode:
Enter the required Pre-shared Key for the access point, which can be a
hexadecimal number or a passphrase.
Figure 4-8 Security Mode- WPA-personal
WPA- enterprise and WPA2-enterprise Mode:
Choose the type of client/server authentication being used by the access
point; EAP-TLS or EAP-PEAP.
EAP-TLS
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
26
Figure 4-9 EAP-TLS

Identity - Enter the user ID to present to the network.

Private key password – Enter the password for your user ID.

EAPOL version - Select the version used (1 or 2) in your access point.

CA Certificates - Upload a CA certificate to present to the access point
for authentication.
EAP-PEAP:

User Name - Enter the user name to present to the network

Password - Enter the password of the network

PEAP Version - Select the PEAP version used at the access point.

Label - Select the label used by the access point.

EAPOL version - Select version (1 or 2) depending on the version used
at the access point

CA Certificates - Upload a CA certificate to present to the access point
for authentication
4.2 Easy Wi-Fi Connection with WPS function
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
27
Purpose:
The setting of the wireless network connection is never easy. To avoid the
complex setting of the wireless connection you can enable the WPS
function.
WPS (Wi-Fi Protected Setup) refers to the easy configuration of the
encrypted connection between the device and the wireless router. The
WPS makes it easy to add new devices to an existing network without
entering long passphrases. There are two modes of the WPS connection,
the PBC mode and the PIN mode.
Note: If you enable the WPS function, you do not need to configure the
parameters such as the encryption type and you don’t need to know the
key of the wireless connection.
Steps:
Figure 4-10 Wi-Fi Settings - WPS
PBC Mode:
PBC refers to the Push-Button-Configuration, in which the user simply has
to push a button, either an actual or virtual one (as the
button
on the configuration interface of the IE browser), on both the Access Point
(and a registrar of the network) and the new wireless client device.
1. Check the checkbox of
to enable WPS.
2. Choose the connection mode as PBC.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
28
Note: Support of this mode is mandatory for both the Access Points and
the connecting devices.
3. Check on the Wi-Fi router to see if there is a WPS button. If yes push
the button and you can see the indicator near the button start flashing,
which means the WPS function of the router is enabled. For detailed
operation, please see the user guide of the router.
4. Push the WPS button to enable the function on the camera.
If there is not a WPS button on the camera, you can also click the virtual
button to enable the PBC function on the web interface.
5. Click Connect button.
When the PBC mode is both enabled in the router and the camera, the
camera and the wireless network is connected automatically.
PIN Mode:
The PIN mode requires a Personal Identification Number (PIN) to be read
from either a sticker or the display on the new wireless device. This PIN
must then be entered to connect the network, usually the Access Point of
the network.
Steps:
1. Choose a wireless connection on the list and the SSID is shown.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
29
Figure 4-11 Wi-Fi Settings – WPS PIN Mode
2. Choose Use route PIN code.
If the PIN code is generated from the router side, you should enter the PIN
code you get from the router side in the Router PIN code field.
3. Click Connect.
Or
You can generate the PIN code on the camera side. And the expired time
for the PIN code is 120 seconds.
1. Click Generate.
2. Enter the code to the router, in the example, enter 48167581 to the
router.
4.3 IP Property Settings for Wireless
Network Connection
The wireless network interface controller is set to DHCP. When you
connect the wireless network you can change the IP-address.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
30
Steps:
1.
Enter the TCP/IP configuration interface.
Configuration> Advanced Configuration> Network> TCP/IP
or
Configuration> Basic Configuration> Network> TCP/IP
Figure 4-12 TCP/IP Settings
2.
Select the NIC as wlan.
3.
Customize the IPv4 address, the IPv4 Subnet Mask and the Default
Gateway.
The setting procedure is the same with that of LAN.
If you want to be assigned the IP address you can check the checkbox to
enable the DHCP.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
31
Chapter 5
Live View
5.1 Live View Page
Purpose:
The live view page allows you to view the real-time video, capture images,
realize PTZ control, set/call presets and configure video parameters.
Log in the network camera to enter the live view page, or you can click
Live View on the menu bar of the main page to enter the live view page.
Descriptions of the live view page:
Figure 5-1 Live View Page
Camera Model:
It lists the camera model you are connecting to.
Online Help:
Click
to get the online help, which will guide you through the basic
32
operations for each function.
Menu Bar:
Click each tab to enter Live View, Playback, Log and Configuration page
respectively.
Display Control:
Click each tab to adjust the layout and the stream type of the live view.
And you can click the drop-down to select the plug-in. For IE (internet
explorer) user, webcomponents and quick time are selectable. And for
Non-IE user, webcomponents, quick time, VLC or MJPEG is selectable if
they are supported by the web browser.
Live View Window:
Display the live video.
Toolbar:
Operations on the live view page, e.g., live view, capture, record, audio
on/off, two-way audio, etc.
PTZ Control:
Panning, tilting and zooming actions of the camera and the lighter and
wiper control (if it supports PTZ function or an external pan/tilt unit has
been installed).
Preset Setting/Calling:
Set and call the preset for the camera (if supports PTZ function or an
external pan/tilt unit has been installed).
5.2 Starting Live View
In the live view window as shown in Figure 5-2, click
on the toolbar to
start the live view of the camera.
Figure 5-2 Live View Toolbar
Table 5-1 Descriptions of the Toolbar
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
33
Icon
Description
Start/Stop live view.
/
The window size is 4:3.
The window size is 16:9.
The original widow size.
Self-adaptive window size.
Live view with the main stream.
Live view with the sub stream.
Live view with the third stream.
Click to select the third-party plug-in.
Manually capture the picture.
Manually start/stop recording.
/
Audio on and adjust volume /Mute.
/
/
Turn on/off microphone.
/
Turn on/off 3D zooming function.
5.3 Recording
and
Capturing
Pictures
Manually
In the live view interface, click
pictures or click
on the toolbar to capture the live
to record the live view. The saving paths of the
captured pictures and clips can be set on the Configuration > Local
Configuration page. To configure remote scheduled recording, please
refer to Section 7.2.
Note: The captured image will be saved as JPEG file or BMP file in your
computer.
5.4 Operating PTZ Control
Purpose:
In the live view interface, you can use the PTZ control buttons to realize
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
34
pan/tilt/zoom control of the camera.
Before you start:
To realize PTZ control, the camera connected to the network must support
the PTZ function or a pan/tilt unit has been installed to the camera. Please
properly set the PTZ parameters on RS-485 settings page referring to
Section 10.8 RS-485 Settings.
5.4.1 PTZ Control Panel
On the live view page, click
to show the PTZ control panel or click
to hide it.
Click the direction buttons to control the pan/tilt movements.
Figure 5-3 PTZ Control Panel
Click the zoom/iris/focus buttons to realize lens control.
Notes:

There are 8 direction arrows ( , , ,
, , ,
,
) in the live view
window when you click and drag the mouse in the relative positions.
 For the cameras which support lens movements only, the direction
buttons are invalid.
Table 5-2 Descriptions of PTZ Control Panel
Icon
Description
Zoom in/out
Focus near/far
Iris +/Light on/off
Wiper on/off
One-touch focus
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
35
Initialize lens
Adjust speed of pan/tilt
movements
5.4.2 Setting / Calling a Preset
 Setting a Preset:
1. In the PTZ control panel, select a preset number from the preset list.
Figure 5-4 Setting a Preset
2. Use the PTZ control buttons to move the lens to the desired position.
• Pan the camera to the right or left.
• Tilt the camera up or down.
• Zoom in or out.
• Refocus the lens.
3. Click
to finish the setting of the current preset.
4. You can click
to delete the preset.
Note: You can configure up to 128 presets.

Calling a Preset:
This feature enables the camera to point to a specified preset scene
manually or when an event takes place.
For the defined preset, you can call it at any time to the desired preset
scene.
In the PTZ control panel, select a defined preset from the list and click
to call the preset.
Or you can place the mouse on the presets interface, and call the preset by
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
36
typing the preset No. to call the corresponding presets.
Figure 5-5 Calling a Preset
5.4.3 Setting / Calling a Patrol
Note:
No less than 2 presets have to be configured before you set a patrol.
Steps:
1. Click
to enter the patrol configuration interface.
2. Select a path No., and click
to add the configured presets.
3. Select the preset, and input the patrol duration and patrol speed.
4. Click OK to save the first preset.
5. Follow the steps above to add the other presets.
Figure 5-6 Add Patrol Path
6. Click
to save a patrol.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
37
7. Click
to start the patrol, and click
8. (Optional) Click
to stop it.
to delete a patrol.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
38
Chapter 6
Network Camera
Configuration
6.1 Configuring Local Parameters
Note: The local configuration refers to the parameters of the live view,
record files and captured pictures. The record files and captured pictures
are the ones you record and captured using the web browser and thus the
saving paths of them are on the PC running the browser.
Steps:
1. Enter the Local Configuration interface:
Configuration > Local Configuration
Figure 6-1 Local Configuration Interface
2. Configure the following settings:

Live View Parameters: Set the protocol type and live view
39
performance.

Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable.
TCP: Ensures complete delivery of streaming data and better video
quality, yet the real-time transmission will be affected.
UDP: Provides real-time audio and video streams.
HTTP: Allows the same quality as of TCP without setting specific
ports for streaming under some network environments.
MULTICAST: It’s recommended to select MCAST type when using
the Multicast function. For detailed information about Multicast,
refer to Section 6.3.1 TCP/IP Settings.

Live View Performance: Set the live view performance to Shortest
Delay, Real Time, Balanced or Best Fluency.

Rules: It refers to the rules on your local browser, select enable or
disable to display or not display the colored marks when the motion
detection, face detection, or intrusion detection is triggered. E.g.:
enabled as the rules are, and the face detection is enabled as well,
when a face is detected, it will be marked with a green rectangle on
the live view.


Image Format: Choose the image format for picture capture.
Record File Settings: Set the saving path of the recorded video files.
Valid for the record files you recorded with the web browser.

Record File Size: Select the packed size of the manually recorded
and downloaded video files to 256M, 512M or 1G. After the
selection, the maximum record file size is the value you selected.

Save record files to: Set the saving path for the manually recorded
video files.

Save downloaded files to: Set the saving path for the
downloaded video files in playback mode.

Picture and Clip Settings: Set the saving paths of the captured
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
40
pictures and clipped video files. Valid for the pictures you captured
with the web browser.

Save snapshots in live view to: Set the saving path of the
manually captured pictures in live view mode.

Save snapshots when playback to: Set the saving path of the
captured pictures in playback mode.

Save clips to: Set the saving path of the clipped video files in
playback mode.
Note: You can click Browse to change the directory for saving the clips
and pictures.
3. Click Save to save the settings.
6.2 Configuring Time Settings
Purpose:
You can follow the instructions in this section to configure the time
synchronization and DST settings.
Steps:
1. Enter the Time Settings interface:
Configuration > Basic Configuration > System > Time Settings
Or Configuration > Advanced Configuration > System > Time
Settings
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
41
Figure 6-2 Time Settings

Select the Time Zone.
Select the Time Zone of your location from the drop-down menu.
 Synchronizing Time by NTP Server.
(1) Check the checkbox to enable the NTP function.
(2) Configure the following settings:
Server Address: IP address of NTP server.
NTP Port: Port of NTP server.
Interval: The time interval between the two synchronizing actions
with NTP server.
Figure 6-3 Time Sync by NTP Server
Note: If the camera is connected to a public network, you should use a
NTP server that has a time synchronization function, such as the server at
the National Time Center (IP Address: 210.72.145.44). If the camera is set in
a customized network, NTP software can be used to establish a NTP server
for time synchronization.
 Synchronizing Time Synchronization Manually
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
42
Enable the Manual Time Sync function and then click
to set the
system time from the pop-up calendar.
Note: You can also check the Sync with computer time checkbox to
synchronize the time of the camera with that of your computer.
Figure 6-4 Time Sync Manually
 Click the DST tab page to enable the DST function and Set the date of
the DST period.
Figure 6-5 DST Settings
2. Click Save to save the settings.
6.3 Configuring Network Settings
6.3.1 Configuring TCP/IP Settings
Purpose:
TCP/IP settings must be properly configured before you operate the
camera over network. The camera supports both the IPv4 and IPv6. Both
versions may be configured simultaneously without conflicting to each
other, and at least one IP version should be configured.
Steps:
1. Enter TCP/IP Settings interface:
Configuration > Basic Configuration > Network > TCP/IP
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
43
Or Configuration > Advanced Configuration > Network > TCP/IP
Figure 6-6 TCP/IP Settings
2. Configure the basic network settings, including the NIC Type, IPv4 or
IPv6 Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway,
MTU settings and Multicast Address.
Notes:

The valid value range of MTU is 500 ~ 1500.

The Multicast sends a stream to the multicast group address and
allows multiple clients to acquire the stream at the same time by
requesting a copy from the multicast group address. Before utilizing
this function, you have to enable the Multicast function of your router.
3. Click Save to save the above settings.
Note: A reboot is required for the settings to take effect.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
44
6.3.2 Configuring Port Settings
Purpose:
You can set the port No. of the camera, e.g. HTTP port, RTSP port and
HTTPS port.
Steps:
1. Enter the Port Settings interface:
Configuration > Basic Configuration > Network > Port
Or Configuration > Advanced Configuration > Network > Port
Figure 6-7 Port Settings
2. Set the HTTP port, RTSP port, HTTPS port and server port of the
camera.
HTTP Port: The default port number is 80, and it can be changed to
any port No. which is not occupied.
RTSP Port: The default port number is 554 and it can be changed to
any port No. ranges from 1024 to 65535.
HTTPS Port: The default port number is 443, and it can be changed to
any port No. which is not occupied.
Server Port: The default server port number is 8000, and it can be
changed to any port No. ranges from 2000 to 65535.
3. Click Save to save the settings.
Note: A reboot is required for the settings to take effect.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
45
6.3.3 Configuring PPPoE Settings
Steps:
1. Enter the PPPoE Settings interface:
Configuration >Advanced Configuration > Network > PPPoE
Figure 6-8 PPPoE Settings
2. Check the Enable PPPoE checkbox to enable this feature.
3. Enter User Name, Password, and Confirm password for PPPoE
access.
Note: The User Name and Password should be assigned by your ISP.
4. Click Save to save and exit the interface.
Note: A reboot is required for the settings to take effect.
6.3.4 Configuring DDNS Settings
Purpose:
If your camera is set to use PPPoE as its default network connection, you
can use the Dynamic DNS (DDNS) for network access.
Before you start:
Registration on the DDNS server is required before configuring the DDNS
settings of the camera.
Steps:
1. Enter the DDNS Settings interface:
Configuration > Advanced Configuration > Network > DDNS
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
46
Figure 6-9 DDNS Settings
2. Check the Enable DDNS checkbox to enable this feature.
3. Select DDNS Type. Four DDNS types are selectable: HiDDNS, IPServer ,
NO-IP, and DynDNS.

DynDNS:
Steps:
(1) Enter Server Address of DynDNS (e.g. members.dyndns.org).
(2) In the Domain text field, enter the domain name obtained from
the DynDNS website.
(3) Enter the Port of DynDNS server.
(4) Enter the User Name and Password registered on the DynDNS
website.
(5) Click Save to save the settings.
Figure 6-10 DynDNS Settings

IP Server:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
47
Steps:
(1) Enter the Server Address of the IP Server.
(2) Click Save to save the settings.
Note: For the IP Server, you have to apply a static IP, subnet mask,
gateway and preferred DNS from the ISP. The Server Address should
be entered with the static IP address of the computer that runs the IP
Server software.
Figure 6-11 IPServer Settings
Note: For the US and Canada area, you can enter 173.200.91.74 as the
server address.

NO-IP:
Steps:
(1)Choose the DDNS Type as NO-IP.
Figure 6-12 NO-IP Settings
(2)Enter the Server Address as www.noip.com
(3)Enter the Domain name you registered.
(4)Enter the Port number, if needed.
(5)Enter the User Name and Password.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
48
(6)Click Save and then you can view the camera with the domain
name.

HiDDNS
Steps:
(1)Choose the DDNS Type as HiDDNS.
Figure 6-13 HiDDNS Settings
(2)Enter the Server Address www.hiddns.com.
(3)Enter the Domain name of the camera. The domain is the same
with the device alias in the HiDDNS server.
(4)Click Save to save the new settings.
Note: A reboot is required for the settings to take effect.
6.3.5 Configuring SNMP Settings
Purpose:
You can set the SNMP function to get camera status, parameters and
alarm related information and manage the camera remotely when it is
connected to the network.
Before you start:
Before setting the SNMP, please download the SNMP software and
manage to receive the camera information via SNMP port. By setting the
Trap Address, the camera can send the alarm event and exception
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
49
messages to the surveillance center.
Note: The SNMP version you select should be the same as that of the
SNMP software. And you also need to use the different version according
to the security level you required. SNMP v1 provides no security and SNMP
v2 requires password for access. And SNMP v3 provides encryption and if
you use the third version, HTTPS protocol must be enabled.
Steps:
1. Enter the SNMP Settings interface:
Configuration > Advanced Configuration > Network > SNMP
Figure 6-14 SNMP Settings
2. Check the corresponding version checkbox (
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
50
,
,
) to enable the feature.
3. Configure the SNMP settings.
Note: The settings of the SNMP software should be the same as the
settings you configure here.
4. Click Save to save and finish the settings.
Note: A reboot is required for the settings to take effect.
6.3.6 Configuring 802.1X Settings
Purpose:
The IEEE 802.1X standard is supported by the network cameras, and when
the feature is enabled, the camera data is secured and user authentication
is needed when connecting the camera to the network protected by the
IEEE 802.1X.
Before you start:
The authentication server must be configured. Please apply and register a
user name and password for 802.1X in the server.
Steps:
1. Enter the 802.1X Settings interface:
Configuration > Advanced Configuration > Network > 802.1X
Figure 6-15 802.1X Settings
2. Check the Enable IEEE 802.1X checkbox to enable the feature.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
51
3. Configure the 802.1X settings, including EAPOL version, user name
and password.
Note: The EAPOL version must be identical with that of the router or
the switch.
4. Enter the user name and password to access the server.
5. Click Save to finish the settings.
Note: A reboot is required for the settings to take effect.
6.3.7 Configuring QoS Settings
Purpose:
QoS (Quality of Service) can help solve the network delay and network
congestion by configuring the priority of data sending.
Steps:
1. Enter the QoS Settings interface:
Configuration >Advanced Configuration > Network > QoS
Figure 6-16 QoS Settings
2. Configure the QoS settings, including video / audio DSCP, event / alarm
DSCP and Management DSCP.
The valid value range of the DSCP is 0-63. The bigger the DSCP value is,
the higher the priority is.
Note: DSCP refers to the Differentiated Service Code Point; and the
DSCP value is used in the IP header to indicate the priority of the data.
3. Click Save to save the settings.
Note: A reboot is required for the settings to take effect.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
52
6.3.8 Configuring UPnP™ Settings
Universal Plug and Play (UPnP™) is a networking architecture that
provides compatibility among networking equipment, software and other
hardware devices. The UPnP protocol allows devices to connect seamlessly
and to simplify the implementation of networks in the home and
corporate environments.
With the function enabled, you don’t need to configure the port mapping
for each port, and the camera is connected to the Wide Area Network via
the router.
Steps:
1. Enter the UPnP™ settings interface.
Configuration >Advanced Configuration > Network > UPnP
2. Check the checkbox to enable the UPnP™ function.
The name of the device when detected online can be edited.
Figure 6-17 Configure UPnP Settings
6.3.9 Email Sending Triggered by Alarm
Purpose:
The system can be configured to send an Email notification to all
designated receivers if an alarm event is detected, e.g., motion detection
event, video loss, video tampering, etc.
Before you start:
Please configure the DNS Server settings under Basic Configuration >
Network > TCP/IP or Advanced Configuration > Network > TCP/IP
before using the Email function.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
53
Steps:
1. Enter the TCP/IP Settings (Configuration > Basic Configuration >
Network > TCP/IP or Configuration > Advanced Configuration >
Network > TCP/IP) to set the IPv4 Address, IPv4 Subnet Mask, IPv4
Default Gateway and the Preferred DNS Server.
Note: Please refer to Section 6.3.1 Configuring TCP/IP Settings for
detailed information.
2. Enter the Email Settings interface:
Configuration > Advanced Configuration > Network > Email
Figure 6-18 Email Settings
3. Configure the following settings:
Sender: The name of the email sender.
Sender’s Address: The email address of the sender.
SMTP Server: The SMTP Server IP address or host name (e.g.,
smtp.263xmail.com).
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
54
SMTP Port: The SMTP port. The default TCP/IP port for SMTP is 25 (not
secured). And the SSL SMTP port is 465.
Enable SSL: Check the checkbox to enable SSL if it is required by the
SMTP server.
Attached Image: Check the checkbox of Attached Image if you want
to send emails with attached alarm images.
Interval: The interval refers to the time between two actions of
sending attached pictures.
Authentication (optional): If your email server requires
authentication, check this checkbox to use authentication to log in to
this server and enter the login user Name and password.
Choose Receiver: Select the receiver to which the email is sent. Up to
2 receivers can be configured.
Receiver: The name of the user to be notified.
Receiver’s Address: The email address of user to be notified.
4. Click Save to save the settings.
6.3.10
Configuring
NAT
(Network
Address
Translation) Settings
Purpose:
1. Enter the NAT settings interface.
Configuration >Advanced Configuration > Network > NAT
2. Choose the port mapping mode.
To port mapping with the default port numbers:
Choose Port Mapping Mode as Auto.
To port mapping with the customized port numbers:
Choose Port Mapping Mode as Manual.
And for manual port mapping, you can customize the value of the port
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
55
number by yourself.
Figure 6-19 Configure NAT Settings
3. Click Save to save the settings.
6.3.11
Configuring FTP Settings
Purpose:
You can configure the FTP server related information to enable the
uploading of the captured pictures to the FTP server. The captured pictures
can be triggered by events or a timing snapshot task.
Steps:
1. Enter the FTP Settings interface:
Configuration >Advanced Configuration > Network > FTP
Figure 6-20 FTP Settings
2. Configure the FTP settings; and the user name and password are
required for login the FTP server.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
56
Directory: In the Directory Structure field, you can select the root
directory, parent directory and child directory. When the parent
directory is selected, you have the option to use the Device Name,
Device Number or Device IP for the name of the directory; and when
the Child Directory is selected, you can use the Camera Name or
Camera No. as the name of the directory.
Upload type: To enable uploading the captured picture to the FTP
server.
Anonymous Access to the FTP Server (in which case the user
name and password won’t be required.): Check the Anonymous
checkbox to enable the anonymous access to the FTP server.
Note: The anonymous access function must be supported by the FTP
server.
3. Click Save to save the settings.
Note: If you want to upload the captured pictures to FTP server, you
have to enable the continuous snapshot or event-triggered snapshot
on Snapshot page. For detailed information, please refer to the
Section 6.6.7.
6.3.12 HTTPS Settings
Purpose:
HTTPS provides authentication of the web site and associated web server
that
one
is
communicating
with,
which
protects
against
Man-in-the-middle attacks. Perform the following steps to set the port
number of https.
Steps:
1. Enter the HTTPS settings interface.
Configuration > Advanced Configuration > Network > HTTPS
2. Create the self-signed certificate or authorized certificate.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
57
Figure 6-21 HTTPS Settings

Create the self-signed certificate
1) Click Create button to enter the creation interface.
Figure 6-22 Create Self-signed Certificate
2) Enter the country, host name/IP, validity and other information.
3) Click OK to save the settings.
Note:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
58
If you already had a certificate installed, the Create Self-signed
Certificate is grayed out.
Create the authorized certificate

1) Click Create button to create the certificate request.
2) Download the certificate request and submit it to the trusted
certificate authority for signature.
3) After receiving the signed valid certificate, import the certificate to
the device.
3. There will be the certificate information after you successfully create
and install the certificate.
Figure 6-23 Installed Certificate
4. Click the Save button to save the settings.
6.4 Configuring Video and Audio Settings
6.4.1 Configuring Video Settings
Steps:
1. Enter the Video Settings interface:
Configuration >Basic Configuration > Video / Audio > Video
Or Configuration > Advanced Configuration > Video / Audio >
Video
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
59
Figure 6-24 Configure Video Settings
2. Select the Stream Type of the camera to main stream (normal),
sub-stream or third stream.
The main stream is usually for recording and live viewing with good
bandwidth, and the sub-stream and third stream can be used for live
viewing when the bandwidth is limited.
3. You can customize the following parameters for the selected main
stream or sub-stream:
Video Type:
Select the stream type to video stream, or video & audio composite
stream. The audio signal will be recorded only when the Video Type is
Video & Audio.
Resolution:
Select the resolution of the video output.
Bitrate Type:
Select the bitrate type to constant or variable.
Video Quality:
When bitrate type is selected as Variable, 6 levels of video quality are
selectable.
Frame Rate:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
60
Set the frame rate to 1/16~25 fps. The frame rate is to describe the
frequency at which the video stream is updated and it is measured by
frames per second (fps). A higher frame rate is advantageous when
there is movement in the video stream, as it maintains image quality
throughout.
Max. Bitrate:
Set the max. bitrate to 32~16384 Kbps. The higher value corresponds to
the higher video quality, but the higher bandwidth is required.
Video Encoding:
If the Stream Type is set to main stream, H.264 and MPEG4 are
selectable, and if the stream type is set to sub stream or third stream,
H.264, MJPEG, and MPEG4 are selectable.
Note: The supported video encoding may differ according to the
different platform.
Profile:
Basic profile, Main Profile and High Profile for coding are selectable.
I Frame Interval:
Set the I-Frame interval to 1~400.
SVC:
Scalable Video Coding is an extension of the H.264/AVC standard. Set it
OFF or ON according to your actual needs.
Smoothing:
It refers to the smoothness of the stream. The higher value of the
smoothing, the better fluency of the stream, though, the video quality
may not be so satisfied. The lower value of the smoothing, the higher
quality of the stream, though it may appear not fluent.
4. Click Save to save the settings.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
61
6.4.2 Configuring Audio Settings
Steps:
1.
Enter the Audio Settings interface
Configuration > Basic Configuration > Video / Audio > Audio
Or Configuration > Advanced Configuration > Video / Audio >
Audio
Figure 6-25 Audio Settings
2. Configure the following settings.
Audio Encoding: G.722.1, G.711 ulaw, G.711alaw, G.726, and MP2L2
are selectable. And 32kbps, 64kbps, and 128kbps are supported if
MP2L2 is selected.
Audio Input: MicIn and LineIn are selectable for the connected
microphone and pickup respectively.
Input Volume: 0-100
Environmental Noise Filter: Set it as OFF or ON. When you set the
function on the noise detected can be filtered.
3.
Click Save to save the settings.
6.4.3 Configuring ROI Encoding
ROI stands for the region of interest. And the ROI encoding enables you to
discriminate the ROI and background information in compression, that is
to say, the technology assigns more encoding resource to the region of
interest to increase the quality of the ROI whereas the background
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
62
information is less focused.
Steps:
1. Enter the ROI settings interface
Configuration > Advanced Configuration > Video / Audio >ROI
Figure 6-26 Region of Interest Settings
2. Draw the region of interest on the image. There are four regions can
be drawn.
3. Choose the stream type to set the ROI encoding.
4. Choose the ROI type.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
63
There are two options for ROI encoding, the fixed region encoding
and the dynamic tracking.

The fixed region encoding is the ROI encoding for the manually
configured area. And you can choose the Image Quality Enhancing
level for ROI encoding, and you can also name the ROI area.

The dynamic region refers to the ROI defined by intelligent
analysis such as human face detection. You can choose the Image
Quality Enhancing level for the ROI encoding.
5. Click Save to save the settings.
6.4.4 Display Info. on Stream
Check the checkbox to enable the function of Dual-VCA which can be used
cooperatively with NVR to implement dual-VCA retrieval during playback.
Figure 6-27 Display Info. on Stream
6.5 Configuring Image Parameters
6.5.1 Configuring Display Settings
Purpose:
You can set the image quality of the camera, including brightness, contrast,
saturation, hue, sharpness, etc.
Note:
The display parameters vary according to the different camera model.
Please refer to the actual interface for details.
Steps:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
64
1. Enter the Display Settings interface:
Configuration > Basic Configuration> Image> Display Settings
Or Configuration > Advanced Configuration> Image> Display
Settings
2. Set the image parameters of the camera.
Note:
In order to guarantee the image quality in the different illumination, it
provides two sets of parameters for user to configure.
Day/night Auto-switch
Figure 6-28 Display Settings of Day/night Auto-switch
 Image Adjustment
Brightness describes bright of the image, which ranges from 1~100, and
the default value is 50.
Contrast describes the contrast of the image, which ranges from 1~100,
and the default value is 50.
Saturation describes the colorfulness of the image color, which ranges
from 1~100, and the default value is 50.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
65
Sharpness describes the edge contrast of the image, which ranges from
1~100, and the default value is 50.
 Exposure Settings
If the camera is equipped with the fixed lens, only Manual is selectable,
and the iris mode is not configurable.
If Auto is selected, you can set the auto iris level from 0~ 100.
For the camera supports P-Iris lens, if P-Iris lens is adopted, then the P-Iris
lens type is selectable, e.g.: Tamron 2.8-8mm F1.2 (M13VP288-IR), or if DC
lens is adopted, then manual and auto are selectable.
The exposure time refers to the electronic shutter time, which ranges from
1 ~ 1/100,000s. Adjust it according to the actual luminance condition.
 Focus Settings
For the camera supports electronic lens, you can set the focus mode as
Manual or Auto. If auto is selected, the focus is adjusted automatically,
and if manual is selected, you can control the lens by adjusting the zoom,
focus, lens initialization, and auxiliary focus via the PTZ control interface.
 Day/Night Switch
Select the day/night switch mode, and configure the smart IR settings from
this option.
Figure 6-29 Day/Night Switch
Day, night, auto, schedule, and triggered by alarm input are selectable for
day/night switch.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
66
Day: the camera stays at day mode.
Night: the camera stays at night mode.
Auto: the camera switches between the day mode and the night mode
according to the illumination automatically. The sensitivity ranges from
0~7, the higher the value is, the easier the mode switches. The filtering
time refers to the interval time between the day/night switch. You can set
it from 5s to 120s.
Schedule: Set the start time and the end time to define the duration for
day/night mode.
Triggered by alarm input: The switch is triggered by alarm input, and
you can set the triggered mode to day or night.
Smart IR gives user an option to turn ON / OFF the IR LED.
Set the smart IR to ON, and Auto and Manual are selectable for IR mode.
Select AUTO, and the IR LED changes according to the actual luminance.
E.g.: if the current scene is bright enough, then the IR LED adjusts itself to
lower power; and if the scene is not bright enough, the IR LED adjusts
itself to higher power.
Select Manual, and you can adjust the IR LED by adjusting the distance.
E.g.: If the object is near the camera, the device adjusts the IR LED to lower
power, and the IR LED is in higher power if the object is far.
 Backlight Settings
BLC: If you focus on an object against strong backlight, the object will be
too dark to be seen clearly. BLC compensates light to the object in the
front to make it clear. OFF, Up, Down, Left, Right, Center and customize
are selectable.
WDR: Wide Dynamic Range can be used when there is a high contrast of
the bright area and the dark area of the scene.
HLC: High Light Compression function can be used when there are strong
lights in the scene affecting the image quality.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
67
 White Balance
White balance is the white rendition function of the camera used to adjust
the color temperature according to the environment.
Figure 6-30 White Balance
 Image Enhancement
Digital Noise Reduction: DNR reduces the noise in the video stream. OFF,
Normal Mode and Expert Mode are selectable. Set the DNR level from
0~100, and the default value is 50 in Normal Mode. Set the DNR level from
both space DNR level [0~100] and time DNR level [0~100] in Expert Mode.
Defog Mode: You can enable the defog function when the environment
is foggy and the image is misty. It enhances the subtle details so that the
image appears clearer.
Electrical Image Stabilizer: EIS reduces the effects of vibration in a
video.
Grey Scale: You can choose the range of the grey scale as [0-255] or
[16-235].
 Video Adjustment
Mirror: It mirrors the image so you can see it inversed. Left/Right,
Up/Down, Center, and OFF are selectable.
Rotate: To make a complete use of the 16:9 aspect ratio, you can enable
the rotate function when you use the camera in a narrow view scene.
When installing, turn the camera to the 90 degrees or rotate the 3-axis
lens to 90 degrees, and set the rotate mode as on, you will get a normal
view of the scene with 9:16 aspect ratio to ignore the needless
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
68
information such as the wall, and get more meaningful information of the
scene.
Scene Mode: Choose the scene as indoor or outdoor according to the real
environment.
Video Standard: 50 Hz and 60 Hz are selectable. Choose according to the
different video standards; normally 50 Hz for PAL standard and 60 Hz for
NTSC standard.
Capture Mode: It’s the selectable video input mode to meet the different
demands of field of view and resolution.
 Other
Some of the camera supports CVBS, SDI, or HDMI output. Please refer to
the actual camera model for details.
Day/Night Scheduled-Switch
Day/Night scheduled-switch configuration interface enables you to set the
separate camera parameters for day and night to guarantee the image
quality in different illumination.
Figure 6-31 Day/Night Scheduled-Switch Configuration Interface
Steps:
1. Click the time line to select the start time and the end time of the
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
69
switch.
2. Click Common tab to configure the common parameters applicable to
the day mode and night mode.
Note:
The detailed information of each parameter please refers to day/night
auto switch session.
3. Click Day tab to configure the parameters applicable for day mode.
4. Click Night tab to configure the parameters applicable for night mode.
Note:
The settings saved automatically if any parameter is changed.
6.5.2 Configuring OSD Settings
Purpose:
You can customize the camera name and time on the screen.
Steps:
1. Enter the OSD Settings interface:
Configuration > Advanced Configuration > Image > OSD Settings
Figure 6-32 OSD Settings
2. Check the corresponding checkbox to select the display of camera
name, date or week if required.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
70
3. Edit the camera name in the text field of Camera Name.
4. Select from the drop-down list to set the time format, date format,
display mode and the OSD font size.
5. Define the font color of the OSD by clicking the drop-down, and black
& white self-adaptive and custom are selectable.
Figure 6-33 Font Color-Custom
6. You can use the mouse to click and drag the text frame
in the live view window to adjust the OSD position.
Figure 6-34 Adjust OSD Location
7. Click Save to activate the above settings.
6.5.3 Configuring Text Overlay Settings
Purpose:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
71
You can customize the text overlay.
Steps:
1. Enter the Text Overlay Settings interface:
Configuration > Advanced Configuration > Image > Text Overlay
Figure 6-35 Text Overlay
2. Check the checkbox in front of textbox to enable the on-screen display.
3. Input the characters in the textbox.
4. (Optional)Use the mouse to click and drag the red text frame
in
the live view window to adjust the text overlay position.
5. Click Save.
Note: Up to 8 text overlays are configurable.
6.5.4 Configuring Privacy Mask
Purpose:
Privacy mask enables you to cover certain areas on the live video to
prevent certain spots in the surveillance area from being live viewed and
recorded.
Steps:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
72
1. Enter the Privacy Mask Settings interface:
Configuration > Advanced Configuration> Image > Privacy Mask
2. Check the checkbox of Enable Privacy Mask to enable this function.
3. Click Draw Area.
Figure 6-36 Privacy Mask Settings
4. Click and drag the mouse in the live video window to draw the mask
area.
Note: You are allowed to draw up to 4 areas on the same image.
5. Click Stop Drawing to finish drawing or click Clear All to clear all of
the areas you set without saving them.
6. Click Save to save the settings.
6.6 Configuring and Handling Alarms
This section explains how to configure the network camera to respond to
alarm events, including motion detection, video tampering, alarm input,
alarm output, exception, face detection, audio exception detection,
intrusion detection, defocus detection, and scene change detection, etc.
These events can trigger the linkage methods, such as Notify Surveillance
Center, Send Email, Trigger Alarm Output, etc.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
73
Notes:
 Check the checkbox of Notify Surveillance Center if you want to the
alarm information pushed to your mobile phone as soon as the
alarm is triggered.
 Click
for help when you configure the intelligent functions,
including face detection, audio exception detection, intrusion
detection, defocus detection, scene change detection, etc. A help
document will guide you to go through the configuration steps.
6.6.1 Configuring Motion Detection
Purpose:
Motion detection detects the moving objects in the configured
surveillance area, and triggers the certain action as a respond to detection.
In order to detect the moving objects accurately and reduce the false
alarm rate, normal configuration and expert configuration are selectable
for different motion detection environment.
 Normal Configuration
Normal configuration adopts one set of parameter for motion detection
during the day and at night.
Tasks:
1. Set the Motion Detection Area.
Steps:
(1) Enter the motion detection settings interface
Configuration > Advanced Configuration> Events > Motion
Detection
(2) Check the checkbox of Enable Motion Detection.
(3) Check the checkbox of Enable Dynamic Analysis for Motion if you
want to mark the detected objects with green rectangles.
Note: Select Disable for rules if you don’t want the detected
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
74
objected displayed with the rectangles. Select disable from
Configuration-Local
Configuration-Live
View
Parameters-rules.
Figure 6-37 Enable Motion Detection
(4) Click Draw Area. Click and drag the mouse on the live video to
draw a motion detection area.
(5) Click Stop Drawing to finish drawing one area.
(6) (Optional) Click Clear All to clear all of the areas.
(7) (Optional) Move the slider to set the sensitivity of the detection.
2. Set the Arming Schedule for Motion Detection.
Steps:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
75
Figure 6-38 Arming Time
(1) Click Edit to edit the arming schedule. The Figure 6-34 shows the
editing interface of the arming schedule.
(2) Choose the day you want to set the arming schedule.
(3) Click
to set the time period for the arming schedule.
(4) (Optional) After you set the arming schedule, you can copy the
schedule to other days.
(5) Click OK to save the settings.
Note: The time of each period can’t be overlapped. Up to 8 periods
can be configured for each day.
Figure 6-39 Arming Time Schedule
3. Set the Alarm Actions for Motion Detection.
Check the checkbox to select the linkage method. Notify surveillance
center, send email, upload to FTP, trigger channel and trigger alarm
output are selectable. You can specify the linkage method when an
event occurs.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
76
Figure 6-40 Linkage Method
 Audible Warning
Trigger the audible warning locally. And it only supported by the
device have the audio output.
 Notify Surveillance Center
Send an exception or alarm signal to remote management software
when an event occurs.
 Send Email
Send an email with alarm information to a user or users when an
event occurs.
Note: To send the Email when an event occurs, you need to refer to
Section 6.6.6 to set the related parameters.
 Upload to FTP
Capture the image when an alarm is triggered and upload the
picture to a FTP server.
Note: Set the FTP address and the remote FTP server first. Refer to
Section 6.3.10 for detailed information.
 Trigger Channel
The video will be recorded when the motion is detected. You have to
set the recording schedule to realize this function. Please refer to
Section 7.2 for detailed information.
 Trigger Alarm Output
Trigger one or more external alarm outputs when an event occurs.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
77
Note: To trigger an alarm output when an event occurs, please refer
to Section 6.6.4 to set the related parameters.
 Expert Configuration
Expert mode is mainly used to configure the sensitivity and proportion of
object on area of each area for different day/night switch.
Figure 6-41 Expert Mode of Motion Detection
 Day/Night Switch OFF
Steps:
(1) Draw the detection area as in the normal configuration mode. Up to 8
areas are supported.
(2) Select OFF for Switch Day and Night Settings.
(3) Select the area by clicking the area No.
(4) Slide the cursor to adjust the sensitivity and proportion of object on
the area for the selected area.
(5) Set the arming schedule and linkage method as in the normal
configuration mode.
(6) Click Save to save the settings.
 Day/Night Auto-Switch
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
78
Steps:
(1) Draw the detection area as in the normal configuration mode. Up to 8
areas are supported.
(2) Select Auto-Switch for Switch Day and Night Settings.
Figure 6-42 Day/Night Auto-Switch
(3) Select the area by clicking the area No.
(4) Slide the cursor to adjust the sensitivity and proportion of object on
the area for the selected area in the daytime.
(5) Slide the cursor to adjust the sensitivity and proportion of object on
the area for the selected area at night.
(6) Set the arming schedule and linkage method as in the normal
configuration mode.
(7) Click Save to save the settings.
 Day/Night Scheduled-Switch
(1) Draw the detection area as in the normal configuration mode. Up to 8
areas are supported.
(2) Select Scheduled-Switch for Switch Day and Night Settings.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
79
Figure 6-43 Day/Night Scheduled-Switch
(3) Select the start time and the end time for the switch timing.
(4) Select the area by clicking the area No.
(5) Slide the cursor to adjust the sensitivity and proportion of object on
the area for the selected area in the daytime.
(6) Slide the cursor to adjust the sensitivity and proportion of object on
the area for the selected area at night.
(7) Set the arming schedule and linkage method as in the normal
configuration mode.
(8) Click Save to save the settings.
6.6.2 Configuring Video Tampering Alarm
Purpose:
You can configure the camera to trigger the alarm when the lens is
covered and take alarm response action.
Steps:
1. Enter the video tampering Settings interface:
Configuration > Advanced Configuration > Events > Video
Tampering
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
80
Figure 6-44 Video Tampering Alarm
2. Check Enable Video Tampering checkbox to enable the video
tampering detection.
3. Set the video tampering area; refer to Task 1 Set the Motion
Detection Area in Section 6.6.1.
4. Click Edit to edit the arming schedule for video tampering. The
arming schedule configuration is the same as the setting of the arming
schedule for motion detection. Refer to Task 2 Set the Arming Schedule
for Motion Detection in Section 6.6.1.
5. Check the checkbox to select the linkage method taken for the video
tampering. Audible warning, notify surveillance center, send email and
trigger alarm output are selectable. Please refer to Task 3 Set the Alarm
Actions for Motion Detection in Section 6.6.1.
6. Click Save to save the settings.
6.6.3 Configuring Alarm Input
Steps:
1. Enter the Alarm Input Settings interface:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
81
Configuration > Advanced Configuration> Events > Alarm Input:
2. Choose the alarm input No. and the Alarm Type. The alarm type can be
NO (Normally Open) and NC (Normally Closed). Edit the name to set a
name for the alarm input (optional).
Figure 6-45 Alarm Input Settings
3. Click Edit to set the arming schedule for the alarm input. Refer to Task
2 Set the Arming Schedule for Motion Detection in Section 6.6.1.
4. Check the checkbox to select the linkage method taken for the alarm
input. Refer to Task 3 Set the Alarm Actions for Motion Detection
in Section 6.6.1.
5. You can also choose the PTZ linking for the alarm input if your camera
is installed with a pan/tilt unit. Check the relative checkbox and select
the No. to enable Preset Calling, Patrol Calling or Pattern Calling.
6. You can copy your settings to other alarm inputs.
7. Click Save to save the settings.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
82
6.6.4 Configuring Alarm Output
Steps:
1. Enter the Alarm Output Settings interface:
Configuration>Advanced Configuration> Events > Alarm Output
2. Select one alarm output channel in the Alarm Output drop-down list.
You can also set a name for the alarm output (optional).
3. The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min,
10min or Manual. The delay time refers to the time duration that the
alarm output remains in effect after alarm occurs.
4. Click Edit to enter the Edit Schedule Time interface. The time
schedule configuration is the same as the settings of the arming schedule
for motion detection Refer to Task 2 Set the Arming Schedule for
Motion Detection in Section 6.6.1.
5. You can copy the settings to other alarm outputs.
6. Click Save to save the settings.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
83
Figure 6-46 Alarm Output Settings
6.6.5 Handling Exception
The exception type can be HDD full, HDD error, network disconnected, IP
address conflicted and illegal login to the cameras.
Steps:
1. Enter the Exception Settings interface:
Configuration > Advanced Configuration> Events > Exception
2. Check the checkbox to set the actions taken for the Exception alarm.
Refer to Task 3 Set the Alarm Actions Taken for Motion Detection in
Section 6.6.1.
Figure 6-47 Exception Settings
3. Click Save to save the settings.
6.6.6 Configuring Line Crossing Detection
This function can be used for detecting people, vehicles and objects
crossing a pre-defined area. The line crossing direction can be set as
bidirectional, from left to right or from right to left. And a series of
linkage method will be triggered if any object is detected.
Steps:
1. Check the Enable Line Crossing Detection checkbox.
2. Click the Draw Area, and a crossing plane will show on the image.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
84
3. Click on the line, and you will see two red squares on each end,
drag one of the red squares to define the arming area.
Figure 6-48 Draw Crossing Line
And you can select the directions as A<->B, A ->B, and B->A.
A<->B: Only the arrow on the B side shows; when an object going across
the plane with both direction can be detected and alarms are triggered.
A->B: Only the object crossing the configured line from the A side to the
B side can be detected.
B->A: Only the object crossing the configured line from the B side to the
A side can be detected.
4. Set the sensitivity [1~100].
5. Choose another line crossing on the dropdown list to configure.
Up to 4 line crossing areas are configurable.
6. Click Save to save the settings.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
85
6.6.7 Configuring Intrusion Detection
Intrusion detection can set an area in the surveillance scene and once the
area is been entered, a set of alarm action is triggered.
Steps:
1. Check the Enable Intrusion Detection checkbox.
2. Click Draw Area, and then draw a rectangle on the image as a
defense region.
Note: when you draw the rectangle, all lines should connect end to
end to each other. Up to four areas are supported.
Figure 6-49 Configuring Intrusion Area
You can click Clear to clear the areas you drawn.
The defense region parameters can be set separately.
3. Choose the region to be configured.
 Threshold: Range [0-10s], the threshold for the time of the
object loitering in the region. If you set the value as 0, alarm is
triggered immediately after the object entering the region.
 Sensitivity: Range [1-100]. The value of the sensitivity defines
the size of the object which can trigger the alarm, when the
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
86
sensitivity is high, a very small object can trigger the alarm.
 Percentage: Range [1-100]. Percentage defines the ratio of the
in-region part of the object which can trigger the alarm. For
example, when you set the percentage as 50%, half of the
object entering the region will trigger the alarm.
Arming Schedule is configured to set the time you want the
function to be enabled.
1. Click Edit to set the arming schedule.
2. Choose to trigger alarm actions as Notify Surveillance Center,
Send Email, Upload to FTP and Trigger Channel or trigger the
Alarm Output.
3. Click Save to save the settings.
6.6.8 Configuring Other Alarm
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
87
1. Enable PIR Alarm
2. Set an “Alarm Name”
3. Set the Linkage Method.
Storage Settings
Before you start:
To configure record settings, please make sure that you have the network
storage device within the network or the SD card inserted in your camera.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
88
6.7 Configuring NAS Settings
Before you start:
The network disk should be available within the network and properly
configured to store the recorded files, log files, etc.
Steps:
1. Add the network disk
(1) Enter the NAS (Network-Attached Storage) Settings interface:
Configuration > Advanced Configuration > Storage > NAS
Figure 6-50 Add Network Disk
(2) Enter the IP address of the network disk, and enter the file path.
(3) Select the mounting type. NFS and SMB/CIFS are selectable. And
you can set the user name and password to guarantee the security
if SMB/CIFS is selected.
Note:
Please refer to the User Manual of NAS for creating the file path.
(4) Click Save to add the network disk.
2. Initialize the added network disk.
(1) Enter the HDD Settings interface (Advanced Configuration >
Storage > Storage Management), in which you can view the
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
89
capacity, free space, status, type and property of the disk.
Figure 6-51 Storage Management Interface
(2) If the status of the disk is Uninitialized, check the corresponding
checkbox to select the disk and click Format to start initializing the
disk.
When the initialization completed, the status of disk will become
Normal.
Figure 6-52 View Disk Status
3. Define the quota for record and pictures.
(1) Input the quota percentage for picture and for record.
(2) Click Save and refresh the browser page to activate the settings.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
90
Figure 6-53 Quota Settings
Notes:
 Up to 8 NAS disks can be connected to the camera.
 To initialize and use the SD card after insert it to the camera, please
refer to the steps of NAS disk initialization.
6.8 Configuring Recording Schedule
Purpose:
There are two kinds of recording for the cameras: manual recording and
scheduled recording. For the manual recording, refer to Section 5.3
Recording and Capturing Pictures Manually. In this section, you can
follow the instructions to configure the scheduled recording. By default,
the record files of scheduled recording are stored in the SD card (if
supported) or in the network disk.
Steps:
1. Enter the Record Schedule Settings interface:
Configuration > Advanced Configuration> Storage > Record
Schedule
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
91
Figure 6-54 Recording Schedule Interface
2. Check the checkbox of Enable Record Schedule to enable scheduled
recording.
3. Set the record parameters of the camera.
Figure 6-55 Record Parameters

Pre-record: The time you set to start recording before the scheduled
time or the event. For example, if an alarm triggers recording at
10:00, and the pre-record time is set as 5 seconds, the camera starts
to record at 9:59:55.
The Pre-record time can be configured as No Pre-record, 5 s, 10 s, 15
s, 20 s, 25 s, 30 s or not limited.

Post-record: The time you set to stop recording after the scheduled
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
92
time or the event. For example, if an alarm triggered recording
ends at 11:00, and the post-record time is set as 5 seconds, the
camera records until 11:00:05.
The Post-record time can be configured as 5 s, 10 s, 30 s, 1 min, 2
min, 5 min or 10 min.
Note: The record parameter configurations vary depending on the
camera model.
4. Click Edit to edit the record schedule.
Figure 6-56 Record Schedule
5. Choose the day to set the record schedule.
(1) Set all-day record or segment record:
 If you want to configure the all-day recording, please check the All
Day checkbox.
 If you want to record in different time sections, check the
Customize checkbox. Set the Start Time and End Time.
Note: The time of each segment can’t be overlapped. Up to 4
segments can be configured.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
93
(2) Select a Record Type. The record type can be Continuous, Motion
Detection, Alarm, Motion | Alarm, Motion & Alarm, PIR Alarm,
Wireless Alarm, Emergency Alarm, or Motion | Alarm Input | PIR |
Wireless | Emergency.
 Continuous
If you select Continuous, the video will be recorded automatically
according to the time of the schedule.
 Record Triggered by Motion Detection
If you select Motion Detection, the video will be recorded when
the motion is detected.
Besides configuring the recording schedule, you have to set the
motion detection area and check the checkbox of Trigger
Channel in the Linkage Method of Motion Detection Settings
interface. For detailed information, please refer to the Step 1 Set
the Motion Detection Area in the Section 6.6.1.
 Record Triggered by Alarm
If you select Alarm, the video will be recorded when the alarm is
triggered via the external alarm input channels.
Besides configuring the recording schedule, you have to set the
Alarm Type and check the checkbox of Trigger Channel in the
Linkage Method of Alarm Input Settings interface. For
detailed information, please refer to Section 6.6.4.
 Record Triggered by Motion & Alarm
If you select Motion & Alarm, the video will be recorded when
the motion and alarm are triggered at the same time.
Besides configuring the recording schedule, you have to
configure the settings on the Motion Detection and Alarm
Input Settings interfaces. Please refer to Section 6.6.1 and
Section 6.6.4 for detailed information.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
94
 Record Triggered by Motion | Alarm
If you select Motion | Alarm, the video will be recorded when
the external alarm is triggered or the motion is detected.
Besides configuring the recording schedule, you have to
configure the settings on the Motion Detection and Alarm
Input Settings interfaces. Please refer to Section 6.6.1 and
Section 6.6.4 for detailed information.
Figure 6-57 Edit Record Schedule
(3) Check the checkbox of Select All and click Copy to copy settings
of this day to the whole week. You can also check any of the
checkboxes before the date and click Copy.
(4) Click OK to save the settings and exit the Edit Record Schedule
interface.
6. Click Save to save the settings.
6.9 Configuring Snapshot Settings
Purpose:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
95
You can configure the scheduled snapshot and event-triggered snapshot.
The captured picture can be stored in the SD card (if supported) or the
netHDD (For detailed information about netHDD, please refer to Section
7.1 Configuring NAS Settings). You can also upload the captured
pictures to a FTP server.
Basic Settings
Steps:
1. Enter the Snapshot Settings interface:
Configuration > Advanced Configuration > Storage > Snapshot
2. Check the Enable Timing Snapshot checkbox to enable continuous
snapshot. Check the Enable Event-triggered Snapshot checkbox to
check event-triggered snapshot.
3. Select the quality of the snapshot.
4. Set the time interval between two snapshots.
5. Click Save to save the settings.
Uploading to FTP
You can follow below configuration instructions to upload the snapshots
to FTP.

Upload continuous snapshots to FTP
Steps:
1) Configure the FTP settings and check Upload Picture checkbox in FTP
Settings interface. Please refer to Section 6.3.10 Configuring FTP
Settings for more details to configure FTP parameters.
2) Check the Enable Timing Snapshot checkbox.

Upload event-triggered snapshots to FTP
Steps:
1) Configure the FTP settings and check Upload Picture checkbox in FTP
Settings interface. Please refer to Section 6.3.8 Configuring FTP
Settings for more details to configure FTP parameters.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
96
2) Check Upload Picture checkbox in Motion Detection Settings or
Alarm Input interface. Please refer to Step 3 Set the Alarm Actions
Taken for Motion Detection in Section 6.6.1, or Step 4 Configuring
External Alarm Input in Section 6.6.4.
3) Check the Enable Event-triggered Snapshot checkbox.
Figure 6-58 Snapshot Settings
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
97
Chapter 7
Playback
Purpose:
This section explains how to view the remotely recorded video files stored
in the network disks or SD cards.
Steps:
1. Click Playback on the menu bar to enter playback interface.
Figure 7-1 Playback Interface
2. Select the date and click Search.
98
Figure 7-2 Search Video
3. Click
to play the video files found on this date.
The toolbar on the bottom of Playback interface can be used to control
playing process.
Figure 7-3 Playback Toolbar
Table 7-1 Description of the buttons
Button
Operation
Button
Play
Capture a picture
Pause
Stop
Operation
/
Audio on and adjust
volume/Mute
/
Speed
down
Download video files
Speed up
Playback by
frame
Start/Stop clipping
video files
/
Download captured
pictures
Enable/Disable digital
zoom
Note:
You can choose the file paths locally for downloaded playback video files
and pictures in Local Configuration interface. Please refer to Section 6.1
for details.
Drag the progress bar with the mouse to locate the exact playback point.
You can also input the time and click
to locate the playback point
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
99
in the Set playback time field. You can also click
to zoom out/in the
progress bar.
Figure 7-4 Set Playback Time
Figure 7-5 Progress Bar
The different colors of the video on the progress bar stand for the
different video types.
Figure 7-6 Video Types
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
100
Chapter 8
Log Searching
Purpose:
The operation, alarm, exception and information of the camera can be
stored in log files. You can also export the log files on your demand.
Before you start:
Please configure network storage for the camera or insert a SD card in the
camera.
Steps:
1. Click Log on the menu bar to enter log searching interface.
Figure 8-1 Log Searching Interface
2. Set the log search conditions to specify the search, including the Major
Type, Minor Type, Start Time and End Time.
3. Click Search to search log files. The matched log files will be displayed
on the Log interface.
101
Figure 8-2 Log Searching
4. To export the log files, click Save log to save the log files in your
computer.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
102
Chapter 9
Others
9.1 Managing User Accounts
Enter the User Management interface:
Configuration >Basic Configuration> Security > User
Or Configuration > Advanced Configuration> Security > User
The admin user has access to create, modify or delete other accounts. Up
to 31 user accounts can be created.
Figure 9-1 User Information

Add a User
Steps:
1. Click Add to add a user.
2. Input the User Name, select Level and input Password.
Notes:
● Different level user owns different permissions. Operator and user
are selectable.
● The system will judge the password strength automatically, it is
highly recommended to set a password with high security level to
ensure the security. A good password should be no less than 6
characters, and is the combination of numeric, upper case letters
and lower case letters.
3. In the Basic Permission field and Camera Configuration field, you
can check or uncheck the permissions for the new user.
4. Click OK to finish the user addition.
Figure 9-2 Add a User

Modify a User
Steps:
1. Left-click to select the user from the list and click Modify.
2. Modify the User Name, Level or Password.
3. In the Basic Permission field and Camera Configuration field, you
can check or uncheck the permissions.
4. Click OK to finish the user modification.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
104
Figure 9-3 Modify a User

Delete a User
Steps:
1. Click to select the user you want to delete and click Delete.
2. Click OK on the pop-up dialogue box to delete the user.
9.2 Authentication
Purpose:
You can specifically secure the stream data of live view.
Steps:
1. Enter
the
Authentication
interface:
Configuration>
Advanced
Configuration> Security > Authentication
Figure 9-4 RTSP Authentication
2. Select the RTSP Authentication type basic or disable in the
drop-down list to enable or disable the RTSP authentication.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
105
Note:
If you disable the RTSP authentication, anyone can access the video stream
by the RTSP protocol via the IP address.
3. Select the Web Authentication as Basic or Digest.
Basic: The basic authentication method is adopted.
Digest: The digest authentication method, which is securer, is
adopted.
4. Click Save to save the settings.
9.3 Anonymous Visit
Purpose:
Enabling this function allows visit for whom doesn’t have the user name
and password of the device.
Steps:
1. Enter the Anonymous Visit interface:
Configuration> Advanced Configuration> Security > Anonymous
Visit
Figure 9-5 Anonymous Visit
2. Set the Anonymous Visit permission Enable or Disable in the
drop-down list to enable or disable the anonymous visit.
3. Click Save to save the settings.
There will be a checkbox of Anonymous by the next time you logging
in.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
106
Figure 9-6 Login Interface with an Anonymous Checkbox
4. Check the checkbox of Anonymous and click Login.
Note:
Only live view is available for the anonymous user.
9.4 IP Address Filter
Purpose:
This function makes it possible for access control.
Steps:
1. Enter the IP Address Filter interface:
Configuration> Advanced Configuration> Security > IP Address
Filter
Figure 9-7 IP Address Filter Interface
2. Check the checkbox of Enable IP Address Filter.
3. Select the type of IP Address Filter in the drop-down list, Forbidden
and Allowed are selectable.
4. Set the IP Address Filter list.

Add an IP Address
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
107
Steps:
(1) Click the Add to add an IP.
(2) Input the IP Adreess.
Figure 9-8 Add an IP
(3) Click the OK to finish adding.

Modify an IP Address
Steps:
(1) Left-click an IP address from filter list and click Modify.
(2) Modify the IP address in the text filed.
Figure 9-9 Modify an IP
(3) Click the OK to finish modifying.

Delete an IP Address
Left-click an IP address from filter list and click Delete.

Delete all IP Addresses
Click Clear to delete all the IP addrsses.
5. Click Save to save the settings.
9.5 Security Service
To enable the remote login, and improve the data communication security,
the camera provides the security service for better user experience.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
108
Steps:
1. Go
to
Configuration
>
Advanced
configuration
>
Security >Security Service to enter the security service configuration
interface.
Figure 9-10 Security Service
2. Check the checkbox of Enable Telnet to enable the remote login by
the telnet, and uncheck the checkbox to disable the telnet.
3. Check the checkbox of Enable SSH to enable the data communication
security, and uncheck the checkbox to disable the SSH.
9.6 Viewing Device Information
Enter the Device Information interface: Configuration > Basic
Configuration> System > Device Information or Configuration >
Advanced Configuration> System > Device Information.
In the Device Information interface, you can edit the Device Name.
Other information of the network camera, such as Model, Serial No.,
Firmware Version, Encoding Version, Number of Channels, Number of
HDDs, Number of Alarm Input and Number of Alarm Output are displayed.
The information cannot be changed in this menu. It is the reference for
maintenance or modification in future.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
109
Figure 9-11 Device Information
9.7 Maintenance
9.7.1 Rebooting the Camera
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or
Configuration
>
Advanced
Configuration>
System
>
Maintenance:
2. Click Reboot to reboot the network camera.
Figure 9-12 Reboot the Device
9.7.2 Restoring Default Settings
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or
Configuration
>
Advanced
Configuration>
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
110
System
>
Maintenance
2. Click Restore or Default to restore the default settings.
Figure 9-13 Restore Default Settings
Note:
After restoring the default settings, the IP address is also restored
to the default IP address, please be careful for this action.
9.7.3 Exporting / Importing Configuration File
Purpose:
Configuration file is used for the batch configuration of the camera, which
can simplify the configuration steps when there are a lot of cameras
needing configuring.
Steps:
1. Enter
the
Maintenance
interface:
Configuration
>
Basic
Configuration> System > Maintenance, or Configuration>Advanced
Configuration> System > Maintenance
2. Click Export to export the current configuration file, and save it to the
certain place.
3. Click Browse to select the saved configuration file and then click
Import to start importing configuration file.
Note:
You need to reboot the camera after importing configuration file.
4. Click Export and set the saving path to save the configuration file in
local storage.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
111
Figure 9-14 Import/Export Configuration File
9.7.4 Upgrading the System
Steps:
1. Enter
the
Maintenance
interface:
Configuration
>
Basic
Configuration> System > Maintenance , or Configuration > Advanced
Configuration> System > Maintenance
2. Select firmware or firmware directory to locate the upgrade file.
Firmware: Locate the exact path of the upgrade file.
Firmware Directory: Only the directory the upgrade file belongs to is
required.
3. Click Browse to select the local upgrade file and then click Upgrade
to start remote upgrade.
Figure 9-15 Remote Upgrade
Note:
The upgrading process will take 1~10 minutes. Please don't disconnect
power of the camera during the process, and the camera reboots
automatically after upgrade.
9.8 RS-232 Settings
The RS-232 port can be used in two ways:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
112

Parameters Configuration: Connect a computer to the camera through
the serial port. Device parameters can be configured by using software
such as HyperTerminal. The serial port parameters must be the same as
the serial port parameters of the camera.

Transparent Channel: Connect a serial device directly to the camera.
The serial device will be controlled remotely by the computer through
the network.
Steps:
1. Enter RS-232 Port Setting interface:
Configuration> Advanced Configuration> System > RS232
Figure 9-16 RS-232 Settings
Note: If you want to connect the camera by the RS-232 port, the
parameters of the RS-232 should be exactly the same with the parameters
you configured here.
2. Click Save to save the settings.
9.9 RS-485 Settings
Purpose:
The RS-485 serial port is used to control the PTZ of the camera. The
configuring of the PTZ parameters should be done before you control the
PTZ unit.
Steps:
1. Enter RS-485 Port Setting interface:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
113
Configuration> Advanced Configuration> System > RS485
Figure 9-17 RS-485 Settings
2. Set the RS-485 parameters and click Save to save the settings.
By default, the Baud Rate is set as 9600 bps, the Data Bit is 8, the stop
bit is 1 and the Parity and Flow Control is None.
Note: The Baud Rate, PTZ Protocol and PTZ Address parameters should
be exactly the same as the PTZ camera parameters.
9.10 Service Settings
Go to Configuration> Advanced Configuration> System > Service to
enter the service settings interface.
Service settings refer to the hardware service the camera supports, and it
varies according to the different cameras.
For the cameras support IR LED, ABF (Auto Back Focus), Auto Defog, or
Status LED, you can go to the hardware service, and select to enable or
disable the corresponding service according to the actual demands.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
114
Appendix
Appendix 1 SADP Software Introduction
 Description of SADP V 2.0
SADP (Search Active Devices Protocol) is a kind of user-friendly and
installation-free online device search tool. It searches the active online
devices within your subnet and displays the information of the devices.
You can also modify the basic network information of the devices using
this software.
 Search active devices online

Search online devices automatically
After launch the SADP software, it automatically searches the online
devices every 15 seconds from the subnet where your computer locates.
It displays the total number and information of the searched devices in
the Online Devices interface. Device information including the device
type, IP address, port number, gateway, etc. will be displayed.
Figure A.1.1 Search Online Devices
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
115
Note: Device can be searched and displayed in the list in 15 seconds after
it went online; it will be removed from the list in 45 seconds after it went
offline.

Search online devices manually
You can also click Refresh to refresh the online device list manually.
The newly searched devices will be added to the list.
Note:
You can click
or
on each column heading to order the
information; you can click
to expand the device table and hide
the network parameter panel on the right side, or click
to show
the network parameter panel.
 Modify network parameters
Steps:
1. Select the device to be modified in the device list and the network
parameters of the device will be displayed in the Modify Network
Parameters panel on the right side.
2. Edit the modifiable network parameters, e.g. IP address and port
number.
3. Enter the password of the admin account of the device in the
Password field and click
to save the changes.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
116
Figure A.1.2 Modify Network Parameters

Restore default password
Steps:
1. Contact our technical engineers to get the serial code.
Note:
Serial code is a series of characters combined by the start time and the
serial number of the device.
2. Input the code in the Serial code field and click Confirm to restore
the default password.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
117
Appendix 2 Port Mapping
The following settings are for TP-LINK router (TL-WR641G). The settings
vary depending on different models of routers.
Steps:
1. Select the WAN Connection Type, as shown below:
Figure A.2.1 Select the WAN Connection Type
2. Set the LAN parameters of the router as in the following figure,
including IP address and subnet mask settings.
Figure A.2.2 Set the LAN parameters
3. Set the port mapping in the virtual severs of Forwarding. By default,
camera uses port 80, 8000 and 554. You can change these ports value
with web browser or client software.
Example:
When the cameras are connected to the same router, you can configure
the ports of a camera as 80, 8000, and 554 with IP address 192.168.1.23,
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
118
and the ports of another camera as 81, 8001, 555, 8201 with IP
192.168.1.24. Refer to the steps as below:
Steps:
1. As the settings mentioned above, map the port 80, 8000, 554 and 8200
for the network camera at 192.168.1.23
2. Map the port 81, 8001, 555 and 8201 for the network camera at
192.168.1.24.
3. Enable ALL or TCP protocols.
4. Check the Enable checkbox and click Save.
Figure A.2.3 Port Mapping
Note:
The port of the network camera cannot conflict with other ports. For
example, some web management port of the router is 80. Change the
camera port if it is the same as the management port.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
119
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2305-LW is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2306-C is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2373-VEP is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2386-LEFN is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2387-LEFN is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2388-LVE is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2388-LVEW is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
120
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2395-LVEF is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2395v2-LVEF is in compliance with the essential requirements
and other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2396-LEF is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2396v2-LEF is in compliance with the essential requirements
and other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2397-LE is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
ALLNET
GmbH
Computersysteme
declares
that
the
device
ALL-CAM2397-LEW is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC. The Declaration of
conformity can be found under this link:
www.allnet.de/downloads.html.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
121
DISCLAIMER_OF_WARRANTY
This Program is free software; you can redistribute it and/or modify it under the terms of the GNU General
Public License as published by the Free Software Foundation; version 2 of the License.
This Program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public License along with this Program; if not, write to the
Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
The full text of the GNU General Public License version 2 is included with the software distribution in the file
LICENSE.GPLv2
NO WARRANTY
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
PERFORMANCE OF THE PROGRAM IS WITH YOU.
THE ENTIRE RISK AS TO THE QUALITY AND
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
IN NO EVENT UNLESS REQUIRED BY
APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Written Offer for Source Code
For binaries that you receive from ALLNET GmbH Computersysteme on physical media or within the download
of the offered firmware that are licensed under any version of the GNU General Public License (GPL) or the GNU
LGPL, you can receive a complete machine-readable copy of the source code by sending a written request to:
ALLNET GmbH Computersysteme
Maistrasse 2
82110 Germering
Your request should include: (i) the name of the covered binary, (ii) the version number of the ALLNET product
containing the covered binary, (iii) your name, (iv) your company name (if applicable) and (v) your return
mailing and email address (if available). We may charge you a nominal fee to cover the cost of the media and
distribution. Your request must be sent within three (3) years of the date you received the GPL or LGPL covered
code. For your convenience, some or all of the source code may also be found at:
http://www.allnet.de/gpl.html
LICENSE.GPLv2
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
02110-1301, USA
51 Franklin Street, Fifth Floor, Boston, MA
Everyone is permitted to copy and distribute verbatim copies of this license document, but
changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it.
By contrast,
the GNU General Public License is intended to guarantee your freedom to share and change free software--to
make sure the software is free for all its users.
This General Public License applies to most of the Free Software
Foundation's software and to any other program whose authors commit to using it.
(Some other Free
Software Foundation software is covered by the GNU Library General Public License instead.)
You can apply it
to your programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for this
service if you wish), that you receive source code or can get it if you want it, that you can change the software
or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the
software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients
all the rights that you have.
You must make sure that they, too, receive or can get the source code.
And you
must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is
no warranty for this free software.
If the software is modified by someone else and passed on, we want its
recipients to know that what they have is not the original, so that any problems introduced by others will not
reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents.
We wish to avoid the danger that
redistributors of a free program will individually obtain patent licenses, in effect making the program
proprietary.
To prevent this, we have made it clear that any patent must be licensed for everyone's free use or
not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0.
This License applies to any program or other work which contains a notice placed by the copyright
holder saying it may be distributed under the terms of this General Public License.
The "Program",
below, refers to any such program or work, and a "work based on the Program" means either the
Program or any derivative work under copyright law: that is to say, a work containing the Program or
a portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term "modification".)
addressed as "you".
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
123
Each licensee is
Activities other than copying, distribution and modification are not covered by this License; they are
outside its scope.
The act of running the Program is not restricted, and the output from the Program
is covered only if its contents constitute a work based on the Program (independent of having been
made by running the Program). Whether that is true depends on what the Program does.
1.
You may copy and distribute verbatim copies of the Program's source code as you receive it, in any
medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and
to the absence of any warranty; and give any other recipients of the Program a copy of this License
along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty
protection in exchange for a fee.
2.
You may modify your copy or copies of the Program or any portion of it, thus forming a work based
on the Program, and copy and distribute such modifications or work under the terms of Section 1
above, provided that you also meet all of these conditions:
a)
You must cause the modified files to carry prominent notices
stating that you changed the
files and the date of any change.
b)
You must cause any work that you distribute or publish, that in whole or in part contains or is
derived from the Program or any part thereof, to be licensed as a whole at no charge to all third
parties under the terms of this License.
c)
If the modified program normally reads commands interactively when run, you must cause it,
when started running for such interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a notice that there is no warranty
(or else, saying that you provide a warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this License.
(Exception: if the
Program itself is interactive but does not normally print such an announcement, your work based
on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole.
If identifiable sections of that
work are not derived from the Program, and can be reasonably considered independent and
separate works in themselves, then this License, and its terms, do not apply to those sections
when you distribute them as separate works.
But when you distribute the same sections as part
of a whole which is a work based on the Program, the distribution of the whole must be on the
terms of this License, whose permissions for other licensees extend to the entire whole, and thus
to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written
entirely by you; rather, the intent is to exercise the right to control the distribution of derivative
or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program
(or with a work based on the Program) on a volume of a storage or distribution medium does not
bring the other work under the scope of this License.
3.
You may copy and distribute the Program (or a work based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2 above provided that you also do one of the
following:
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
124
a)
Accompany it with the complete corresponding machine-readable source code, which must be
distributed under the terms of Sections
and 2 above on a medium customarily used for software
interchange; or,
b)
Accompany it with a written offer, valid for at least three years, to give any third party, for a
charge no more than your cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code, to be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange; or,
c)
Accompany it with the information you received as to the offer to distribute corresponding
source code.
(This alternative is allowed only for noncommercial distribution and only if you
received the program in object code or executable form with such an offer, in accord with
Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it.
For
an executable work, complete source code means all the source code for all modules it contains, plus
any associated interface definition files, plus the scripts used to control compilation and installation of
the executable.
However, as a special exception, the source code distributed need not include
anything that is normally distributed (in either source or binary form) with the major components
(compiler, kernel, and so on) of the operating system on which the executable runs, unless that
component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place,
then offering equivalent access to copy the source code from the same place counts as distribution of
the source code, even though third parties are not compelled to copy the source along with the object
code.
4.
You may not copy, modify, sublicense, or distribute the Program except as expressly provided under
this License.
Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and
will automatically terminate your rights under this License. However, parties who have received copies,
or rights, from you under this License will not have their licenses terminated so long as such parties
remain in full compliance.
5.
You are not required to accept this License, since you have not signed it.
However, nothing else
grants you permission to modify or distribute the Program or its derivative works.
prohibited by law if you do not accept this License.
These actions are
Therefore, by modifying or distributing the
Program (or any work based on the Program), you indicate your acceptance of this License to do so,
and all its terms and conditions for copying, distributing or modifying the Program or works based on
it.
6.
Each time you redistribute the Program (or any work based on the Program), the recipient
automatically receives a license from the original licensor to copy, distribute or modify the Program
subject to these terms and conditions.
You may not impose any further restrictions on the recipients'
exercise of the rights granted herein. You are not responsible for enforcing compliance by third
parties to this License.
7.
If, as a consequence of a court judgment or allegation of patent infringement or for any other reason
(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not excuse you from the conditions
of this License.
If you cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not distribute the
Program at all.
For example, if a patent license would not permit royalty-free redistribution of the
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
125
Program by all those who receive copies directly or indirectly through you, then the only way you
could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance
of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or
to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free
software distribution system, which is implemented by public license practices.
Many people have made
generous contributions to the wide range of software distributed through that system in reliance on consistent
application of that system; it is up to the author/donor to decide if he or she is willing to distribute software
through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this
License.
8.
If the distribution and/or use of the Program is restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder who places the Program under this License may
add an explicit geographical distribution limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded.
In such case, this License incorporates the
limitation as if written in the body of this License.
9.
The Free Software Foundation may publish revised and/or new versions of the General Public License
from time to time.
Such new versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies a version number of this
License which applies to it and "any later version", you have the option of following the terms and conditions
either of that version or of any later version published by the Free Software Foundation.
If the Program does
not specify a version number of this License, you may choose any version ever published by the Free Software
Foundation.
10.
If you wish to incorporate parts of the Program into other free programs whose distribution
conditions are different, write to the author to ask for permission.
For software which is copyrighted
by the Free Software Foundation, write to the Free Software Foundation; we sometimes make
exceptions for this.
Our decision will be guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM,
TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
THE
SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
126
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE
THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO
OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best
way to achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program.
It is safest to attach them to the start of each
source file to most effectively convey the exclusion of warranty; and each file should have at least the
"copyright" line and a pointer to where the full notice is found.
<one line to give the program's name and a brief idea of what it does.> Copyright (C) <year>
<name of
author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General
Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option)
any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even
the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
See the GNU General
Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to
the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301, USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive,
make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for
details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public
License.
Of course, the commands you use may be called something other than `show w' and `show c'; they
could even be mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a
"copyright disclaimer" for the program, if necessary.
Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
`Gnomovision' (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
127
This General Public License does not permit incorporating your program into proprietary programs.
If
your program is a subroutine library, you may consider it more useful to permit linking proprietary applications
with the library.
If this is what you want to do, use the GNU Lesser General Public License instead of this
License.
LICENSE.LGPLv2.1
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301
USA Everyone is permitted to copy and distribute verbatim copies of this license document, but
changing it is not allowed.
[This is the first released version of the Lesser GPL.
It also counts as the successor
of the GNU Library Public License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it.
By
contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free
software--to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software
packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.
You can
use it too, but we suggest you first think carefully about whether this license or the ordinary General Public
License is the better strategy to use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price.
Our General Public
Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge
for this service if you wish); that you receive source code or can get it if you want it; that you can change the
software and use pieces of it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to
ask you to surrender these rights.
These restrictions translate to certain responsibilities for you if you
distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients
all the rights that we gave you.
You must make sure that they, too, receive or can get the source code.
If you
link other code with the library, you must provide complete object files to the recipients, so that they can relink
them with the library after making changes to the library and recompiling it.
And you must show them these
terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this
license, which gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library.
Also, if the library is modified by someone else and passed on, the recipients should know that what they have
is not the original version, so that the original author's reputation will not be affected by problems that might
be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program.
We wish to make
sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license
from a patent holder.
Therefore, we insist that any patent license obtained for a version of the library must be
consistent with the full freedom of use specified in this license.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
128
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License.
This
license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different
from the ordinary General Public License.
We use this license for certain libraries in order to permit linking
those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the
two is legally speaking a combined work, a derivative of the original library.
The ordinary General Public
License therefore permits such linking only if the entire combination fits its criteria of freedom.
The Lesser
General Public License permits more lax criteria for linking other code with the library.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom
than the ordinary General Public License.
over competing non-free programs.
License for many libraries.
It also provides other free software developers Less of an advantage
These disadvantages are the reason we use the ordinary General Public
However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a
certain library, so that it becomes a de-facto standard.
use the library.
To achieve this, non-free programs must be allowed to
A more frequent case is that a free library does the same job as widely used non-free libraries.
In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General
Public License.
In other cases, permission to use a particular library in non-free programs enables a greater number of
people to use a large body of free software.
For example, permission to use the GNU C Library in non-free
programs enables many more people to use the whole GNU operating system, as well as its variant, the
GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the
user of a program that is linked with the Library has the freedom and the wherewithal to run that program
using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow.
the difference between a "work based on the library" and a "work that uses the library".
Pay close attention to
The former contains
code derived from the library, whereas the latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0.
This License Agreement applies to any software library or other program which contains a notice
placed by the copyright holder or other authorized party saying it may be distributed under the terms
of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data prepared so as to be conveniently linked
with application programs (which use some of those functions and data) to form executables.
The "Library", below, refers to any such software library or work which has been distributed under these
terms.
A "work based on the Library" means either the Library or any derivative work under copyright law:
that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or
translated straightforwardly into another language.
(Hereinafter, translation is included without limitation in
the term "modification".)
"Source code" for a work means the preferred form of the work for making modifications to it.
For a
library, complete source code means all the source code for all modules it contains, plus any associated interface
definition files, plus the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
129
outside its scope.
The act of running a program using the Library is not restricted, and output from such a
program is covered only if its contents constitute a work based on the Library (independent of the use of the
Library in a tool for writing it).
Whether that is true depends on what the Library does and what the program
that uses the Library does.
1.
You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in
any medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and
to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty
protection in exchange for a fee.
2.
You may modify your copy or copies of the Library or any portion of it, thus forming a work based on
the Library, and copy and distribute such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a)
The modified work must itself be a software library.
b)
You must cause the files modified to carry prominent notices stating that you changed the files
and the date of any change.
c)
You must cause the whole of the work to be licensed at no charge to all third parties under the
terms of this License.
d)
If a facility in the modified Library refers to a function or a table of data to be supplied by an
application program that uses the facility, other than as an argument passed when the facility is
invoked, then you must make a good faith effort to ensure that, in the event an application does
not supply such function or table, the facility still operates, and performs whatever part of its
purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely
well-defined independent of the application.
Therefore, Subsection 2d requires that any
application-supplied function or table used by this function must be optional: if the application
does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole.
If identifiable sections of that work are
not derived from the Library, and can be reasonably considered independent and separate works in
themselves, then this License, and its terms, do not apply to those sections when you distribute them
as separate works.
But when you distribute the same sections as part of a whole which is a work
based on the Library, the distribution of the whole must be on the terms of this License, whose
permissions for other licensees extend to the entire whole, and thus to each and every part regardless
of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely
by you; rather, the intent is to exercise the right to control the distribution of derivative or collective
works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a
work based on the Library) on a volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3.
You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a
given copy of the Library.
To do this, you must alter all the notices that refer to this License, so that
they refer to the ordinary GNU General Public License, version 2, instead of to this License.
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
130
(If a
newer version than version 2 of the ordinary GNU General Public License has appeared, then you can
specify that version instead if you wish.)
Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public
License applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a
library.
4.
You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object
code or executable form under the terms of Sections 1 and 2 above provided that you accompany it
with the complete corresponding machine-readable source code, which must be distributed under the
terms of Sections 1 and 2 above on a medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same place satisfies the requirement to distribute the source
code, even though third parties are not compelled to copy the source along with the object code.
5.
A program that contains no derivative of any portion of the Library, but is designed to work with the
Library by being compiled or linked with it, is called a "work that uses the Library".
Such a work, in
isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative
of the Library (because it contains portions of the Library), rather than a "work that uses the library".
The
executable is therefore covered by this License. Section 6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from a header file that is part of the Library, the object
code for the work may be a derivative work of the Library even though the source code is not. Whether this is
true is especially significant if the work can be linked without the Library, or if the work is itself a library.
The
threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros
and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of
whether it is legally a derivative work.
(Executables containing this object code plus portions of the Library
will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under
the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are
linked directly with the Library itself.
6.
As an exception to the Sections above, you may also combine or link a "work that uses the Library"
with the Library to produce a work containing portions of the Library, and distribute that work under
terms of your choice, provided that the terms permit modification of the work for the customer's own
use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the
Library and its use are covered by this License.
You must supply a copy of this License.
If the work during
execution displays copyright notices, you must include the copyright notice for the Library among them, as well
as a reference directing the user to the copy of this License.
a)
Also, you must do one of these things:
Accompany the work with the complete corresponding machine-readable source code for the
Library including whatever changes were used in the work (which must be distributed under
Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the
complete machine-readable "work that uses the Library", as object code and/or source code, so
that the user can modify the Library and then relink to produce a modified executable containing
the modified Library.
(It is understood that the user who changes the contents of definitions
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
131
files in the Library will not necessarily be able to recompile the application to use the modified
definitions.)
b)
Use a suitable shared library mechanism for linking with the Library.
A suitable mechanism is
one that (1) uses at run time a copy of the library already present on the user's computer system,
rather than copying library functions into the executable, and (2) will operate properly with a
modified version of the library, if the user installs one, as long as the modified version is
interface-compatible with the version that the work was made with.
c)
Accompany the work with a written offer, valid for at least three years, to give the same user the
materials specified in Subsection 6a, above, for a charge no more than the cost of performing this
distribution.
d)
If distribution of the work is made by offering access to copy from a designated place, offer
equivalent access to copy the above specified materials from the same place.
e)
Verify that the user has already received a copy of these materials or that you have already sent
this user a copy.
For an executable, the required form of the "work that uses the Library" must include any data and
utility programs needed for reproducing the executable from it.
However, as a special exception, the
materials to be distributed need not include anything that is normally distributed (in either source or
binary form) with the major components (compiler, kernel, and so on) of the operating system on
which the executable runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries
that do not normally accompany the operating system.
Such a contradiction means you cannot use
both them and the Library together in an executable that you distribute.
7.
You may place library facilities that are a work based on the Library side-by-side in a single library
together with other library facilities not covered by this License, and distribute such a combined
library, provided that the separate distribution of the work based on the Library and of the other
library facilities is otherwise permitted, and provided that you do these two things:
a)
Accompany the combined library with a copy of the same work based on the Library,
uncombined with any other library facilities.
This must be distributed under the terms of the
Sections above.
b)
Give prominent notice with the combined library of the fact that part of it is a work based on the
Library, and explaining where to find the accompanying uncombined form of the same work.
8.
You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided
under this License.
Any attempt otherwise to copy, modify, sublicense, link with, or distribute the
Library is void, and will automatically terminate your rights under this License.
However, parties who
have received copies, or rights, from you under this License will not have their licenses terminated so
long as such parties remain in full compliance.
9.
You are not required to accept this License, since you have not signed it.
However, nothing else
grants you permission to modify or distribute the Library or its derivative works.
prohibited by law if you do not accept this License.
These actions are
Therefore, by modifying or distributing the
Library (or any work based on the Library), you indicate your acceptance of this License to do so, and
all its terms and conditions for copying, distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically
receives a license from the original licensor to copy, distribute, link with or modify the Library subject
to these terms and conditions.
You may not impose any further restrictions on the recipients'
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
132
exercise of the rights granted herein. You are not responsible for enforcing compliance by third
parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason
(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not excuse you from the conditions
of this License.
If you cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not distribute the Library
at all.
For example, if a patent license would not permit royalty-free redistribution of the Library by
all those who receive copies directly or indirectly through you, then the only way you could satisfy
both it and this License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance
of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or
to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free
software distribution system which is implemented by public license practices.
Many people have made
generous contributions to the wide range of software distributed through that system in reliance on consistent
application of that system; it is up to the author/donor to decide if he or she is willing to distribute software
through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this
License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder who places the Library under this License may
add an explicit geographical distribution limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded.
In such case, this License incorporates the
limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public
License from time to time. Such new versions will be similar in spirit to the present version, but may
differ in detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Library specifies a version number of this
License which applies to it and "any later version", you have the option of following the terms and conditions
either of that version or of any later version published by the Free Software Foundation.
If the Library does
not specify a license version number, you may choose any version ever published by the Free Software
Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions
are incompatible with these, write to the author to ask for permission.
For software which is
copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes
make exceptions for this.
Our decision will be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO
THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
133
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU.
THE ENTIRE RISK
SHOULD THE LIBRARY
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH
ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we
recommend making it free software that everyone can redistribute and change.
You can do so by permitting
redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library.
It is safest to attach them to the start of
each source file to most effectively convey the exclusion of warranty; and each file should have at least the
"copyright" line and a pointer to where the full notice is found.
<one line to give the library's name and a brief idea of what it does.> Copyright (C) <year>
<name of
author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser
General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at
your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even
the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
See the GNU Lesser
General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not,
write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301
USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a
"copyright disclaimer" for the library, if necessary.
Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs)
written by James Random Hacker.
<signature of Ty Coon>, 1 April 1990 Ty Coon, President of Vice
That's all there is to it!
© ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
134
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement