Allnet ALL0199AP Owner Manual

Allnet ALL0199AP Owner Manual
i
A
■ Contents
Outdoor
Wireless Access Point
User’s Manual
Before operating the unit, please read this manual thoroughly, and
retain it for future reference.
CHAPTER 1.
1.1
1.2
1.3
1.4
1.5
1.6
HARDWARE INSTALLATION ........................................... 1
BEFORE YOU START ............................................................................. 1
LOCATE THE ACCESS POINT AND INLINE POWER INJECTOR PORTS .......... 2
INSTALLING THE ANTENNAS ................................................................... 3
INSTALLING THE CONSOLE PORT CABLE................................................. 4
CONNECTING THE POWER SUPPLY AND ETHERNET CABLE ....................... 4
OUTDOOR INSTALLATION ....................................................................... 5
CHAPTER 2.
NETWORK TOPOLOGIES................................................. 6
2.1 CONFIGURATION EXAMPLES .................................................................. 7
2.1.1 Wireless Access Bridge................................................................. 7
2.1.2 Wireless Access Router with PPPoE Ethernet connection........... 8
2.1.3 Wireless Access Router with dynamic IP Ethernet connection .... 9
2.1.4 Wireless Access Router with static IP Ethernet connection ....... 10
CHAPTER 3.
INITIAL CONFIGURATION .............................................. 11
3.1 CONFIGURE REQUIREMENTS ............................................................... 11
3.2 CONFIGURE THE AP............................................................................ 13
3.2.1 Configure the AP as a Bridge...................................................... 14
3.2.2 Configure the AP as a Router with PPPoE Ethernet connection 15
3.2.3 Configure the AP as a Router with dynamic IP address Ethernet
..................................................................................................... 20
3.2.4 Configure the AP as a Router with static IP address Ethernet ... 21
3.3 CONFIGURE WIRELESS RELATED PARAMETERS..................................... 23
3.4 SECURITY ........................................................................................... 24
3.4.1 WEP encryption........................................................................... 24
3.4.2 Hide the SSID.............................................................................. 24
3.4.3 Deny ‘ANY’ client station ............................................................. 24
3.4.4 IEEE 802.1x Access Control ....................................................... 25
3.4.5 MAC based Access Control ........................................................ 26
3.5 CONFIGURE DHCP SERVER ................................................................ 27
3.6 CONFIGURE VIRTUAL SERVER ............................................................. 28
3.7 CONFIGURE ROUTING TABLE ............................................................... 30
3.8 CONFIGURE BRIDGE ............................................................................ 31
3.9 CONFIGURE SNMP............................................................................. 32
3.10 CONFIGURATION REVIEW AND APPLY THE NEW SETTINGS .................... 34
3.11 UTILITY............................................................................................... 36
3.11.1 System Info.................................................................................. 36
ii
1
3.11.2 Software Upgrade ....................................................................... 37
CHAPTER 4.
TELNET CONFIGURATION............................................. 38
CHAPTER 5.
SPECIFICATIONS ............................................................ 47
CHAPTER 6.
DEFAULT SETTINGS ...................................................... 50
CHAPTER 7.
REGULATORY COMPLIANCE INFORMATION ............. 59
Chapter 1. Hardware Installation
This chapter describes the procedures for installing the SendFar Outdoor
Access Point.
1.1
Before You Start
After unpacking the system, make sure the following items are present and
in good condition.
1.
2.
3.
4.
5.
6.
7.
7.
8.
10.
11.
12.
Access Point
Inline Power Injector
AC Power Cord
MIL-C-5015 style RS232 Console Port Cable
Grounding Wire
Cross over Ethernet Cable
Two rubber dipole antenna
30M MIL-C-5015 style Ethernet Cable
Mast Mounting Kit
Wall Mounting Kit
User’s Manual Disk
Simple Spanner
1
8
2
9
3
10
4
6
5
11
12
7
2
1.2 Locate the Access Point and Inline Power
Injector Ports
Special Ethernet port 1 for connecting the MIL-C-5015 style Ethernet
Cable
Special serial port 2 for connecting the MIL-C-5015 style RS-232
console port cable
Grounding port 3.
Special N-Type connector 4 for connecting the antenna or RF cable.
Power & Data output port 5 for connecting the other of the MIL-C5015 style Ethernet Cable
Data input port 6 for connecting the Ethernet Cable to a Hub Switch
Router or a PC.
3
1.3
Installing the Antennas
Step 1: With the unit powered off, attach the dipole antenna to the antenna
connector as shown in Figure 1.3.
NOTE: Do not over-tighten; finger tight is sufficient. Position the antenna
vertically for best omni-directional signal reception.
Before installing your WLAN system, we recommend that you test the
Access Point using the dipole antenna included in your package. Once
testing is completed, install your Access Point for use with the appropriate
antenna for your application.
4
1.4
Installing the Console Port Cable
Step 2: Attach the Console Port cable to the Serial Port. Attach the other
cable end to the Serial Port on a PC running a terminal emulation program,
and set the terminal to 115200 Baud, No-Parity, 8 data bits, 1 Stop bit, and
ANSI compatible.
NOTE: This connection is required for setting up initial configuration
information.
After configuration is completed, this cable may be removed until additional
configuration is required via the Serial Port.
5
1.6
Outdoor Installation
Outdoor Access Point device can be mounted on the side of a
building or mounted to an mast as shown in following:
1.5 Connecting the power supply and Ethernet
cable
Step 3 Plug the female end of the power cord into the Inline Power Injector,
and then plug the male end of the power cord into a power outlet or power
strip. The Power LED on the front of the Inline Power Injector will light up.
Step 4 Run the cross over Ethernet cable (included in your package) from
Data Input Port (on the front of the Inline Power Injector) to the Ethernet
Port on the PC we mentioned above.
NOTE: This connection is required for setting up initial configuration
information. After configuration is completed, this cable will be removed,
and then you should run an Ethernet cable from Data Input Port (on the
front of the Inline Power Injector) to the LAN connection (such as a hub or
concentrator).
Step 5 Plug the MIL-C-5015 style Ethernet connector into the Special
Ethernet port on the back of the access point.
Step 6 Plug the RJ-45 Ethernet connector (the other end of the Special
Ethernet cable) into the Power & Data Output Port on the front of the Inline
Power Injector. When the Access Point receives power over the Ethernet
cable, the Access Point will start its boot sequence and the Active LED on
the front of the Inline Power Injector will light up.
A wall (side) mount allows for mounting the Outdoor AP on the side of
a building. This will provide a convenient mounting location when the
roof overhang is not excessive and/or the location is high enough to
provide a clear line of sight.
Grounding
A safety grounding system is necessary to protect your outdoor
installation from lightning strikes and the build-up of static electricity.
So direct grounding of the antenna mast, Outdoor AP and
Surge Arrester is very important. And so mounting the Outdoor AP on
the antenna mast, you have to connect the Outdoor AP to the same
grounding system with the AC wall outlet.
The grounding system must comply with the National Electrical Code
and safety standards that apply in your country. Always check with a
qualified electrician if you are in doubt as to whether your outdoor
installation is properly grounded.
6
Chapter 2. Network Topologies
This chapter describes several main types of installations commonly
implemented using the Outdoor Wireless Access Point (AP). This is by no
means intended to be an exhaustive list of all possible configurations, but
rather shows examples of some of the more common implementations (as
shown in Figure 2-1).
7
2.1
Configuration Examples
2.1.1 Wireless Access Bridge
1. Set the Outdoor AP as a bridge (bridge IP address is 192.168.2.1).
Figure 2-1
The outdoor wireless AP can perform in router or bridge modes. In a
wireless topology, all communication between network stations is done
through a centralized Access Point. To show some possibilities of wireless
topologies, the following examples are provided:
1. Wireless Access Bridge
2. Wireless Access Router with PPPoE Ethernet connection
3. Wireless Access Router with dynamic IP address Ethernet
4. Wireless Access Router with static IP address Ethernet
2. Set Wireless parameters on Outdoor AP: Channel (1) and SSID
(wireless)
3. Set Wireless parameters on client stations PC1, PC2 and PC3:
SSID (wireless).
4. Left side stations are transparent to the right side network.
5. DHCP server assigns IP address to PC1, PC2 and PC3.
8
9
2.1.2 Wireless Access Router with PPPoE Ethernet
connection
2.1.3 Wireless Access Router with dynamic IP Ethernet
connection
1. Set the Outdoor AP as a Router (Wireless Interface IP is 192.168.1.1,
Ethernet Interface IP is 192.168.2.1, must turn on NAT on Ethernet
Interface and turn off NAT on Wireless interface, default route is
0.0.0.0).
1. Set the Outdoor AP as a Router (Wireless Interface IP is 192.168.1.1,
must turn on NAT on Ethernet Interface and turn off NAT on Wireless
interface).
2. Turn on PPPoE Interface (Interface NO.3) and specify that your
personal ISP provided PPPoE Username and PPPoE Password to
enable ADSL broadband access.
2. Enable DHCP client on the Ethernet Interface of the Outdoor AP
(This AP will got IP / Gateway / DNS from the DHCP server).
3. Set Wireless parameters on the Outdoor AP: Channel (1) and SSID
(wireless)
3. Set Wireless parameters on Outdoor AP: Channel (1) and SSID
(wireless)
4. Turn on DHCP server on the Outdoor AP and assign IP address to
PC1, PC2 and PC3.
4. Turn on DHCP server on the Outdoor AP and assign IP address to
PC1, PC2 and PC3.
6. Set Wireless parameters on client stations PC1, PC2 and PC3:
SSID (wireless).
5. Set Wireless parameters on client stations PC1, PC2 and PC3:
SSID (wireless).
10
2.1.4 Wireless Access Router with static IP Ethernet
connection
11
Chapter 3. Initial Configuration
This chapter describes how to easy setup and configure the Wireless
Broadband Access Point (AP) initially. The AP can be configured into a
bridge and a broadband wireless router to meet different applications.
Users can use a wired LAN-attached computer to configure the AP through
a web browser or a telnet session on a LAN computer.
In this chapter, we only describe how to quickly configure the AP with a web
browser. For detailed descriptions of the many configuration parameters
and network configuration, refer to Chapter 4.
3.1
Configure Requirements
The AP is shipped with configuration that can be utilized right out of the box.
Default configuration is as a bridge between an Ethernet and wireless
network. Users simply need to attach the AP to your wired LAN. If users
would like to configure the AP, please refer to the following procedures.
Before setup, we must install AP first
1. Set the Outdoor AP as a Router (Wireless Interface IP is 192.168.1.1,
Ethernet Interface IP is 192.168.2.1, must turn on NAT on Ethernet
Interface and turn off NAT on Wireless interface, default route is
192.168.2.254).
2. Set Wireless parameters on Outdoor AP: Channel (1) and SSID
(wireless)
1.
Connect power adaptor and power on the AP
2.
Connect the Ethernet cable for connecting the AP to the network
3.
Connect a computer to the same network with this AP
4.
Start your Microsoft Internet Explorer web browser program from a
LAN-attached computer. To access the web interface of the AP, you
have to disable Access the Internet using a proxy server function in
Windows 2000 [Control Panel / Internet Options / Connections/LAN
Settings] as shown in Figure 3-1.
5.
Type the IP address and HTTP port of the AP (default port is 2000, IP
is 192.168.2.1) in the address field (http://192.168.2.1:2000/) and
press Enter. Make sure that the IP addresses of AP and your computer
are in the same subnet.
6.
After the connection is established, you will see the user identification
window as shown in Figure3-2, and key-in the proper User Name and
Password to see the web user interface of the AP. The default user
name and password is root and root, respectively
3. Turn on DHCP server on the Outdoor AP and assign IP address to
PC1, PC2 and PC3.
4. Set Wireless parameters on client stations PC1, PC2 and PC3:
SSID (wireless).
12
13
3.2
Configure the AP
The AP can be configured into four operation modes:
1.
2.
3.
4.
Outdoor Wireless Bridge
Outdoor Wireless Router with PPPoE Ethernet connection
Outdoor Wireless Router with dynamic IP address Ethernet
Outdoor Wireless Router with static IP address Ethernet
The AP is shipped with default configuration is as a bridge between an
Ethernet and wireless network. Users simply need to attach the AP to your
wired LAN. If users would like to configure the AP, please refer to the
following procedures.
The web user interface can be grouped into Quick setup, Basic
Configuration, Advanced Configuration and Utility as shown in Figure 3-3.
The left frame contains, in a tree structure, the contents of the AP web
configuration interface. Move through the tree by clicking on an icon to
expand or collapse the tree. The nodes on the tree represent web pages
that allow you to view and modify the parameters of the AP.
Figure 3-1
If users want to connect multiple wireless computers to a broadband (ADSL
or Cable) modem or an Ethernet switch to surf the Internet, you need to
configure the AP as a broadband wireless router to share a single IP
address with the multiple wireless computers as described as follows.
Figure 3-2
Figure 3-3
14
15
3.2.1 Configure the AP as a Bridge
3.2.2 Configure the AP as a Router with PPPoE Ethernet
connection
Configure TCP/IP parameters
Configure TCP/IP parameters
1.
1.
Click Advanced Config, select Bridging, and then click Disable for
Bridge Function as shown in Figure 3-4. After that, click FINISH at
the bottom of this page to complete the modification of this page.
2.
If you are an ADSL subscriber, you need specify that your personal ISP
PPPoE username and password to enable ADSL broadband access, in
here, click Basic Config, select ISP (as shown in Figure 3-5), In this
page, enter MODIFY button to setup the correct ISP parameters: ISP
Name, ISP Phone, PPPoE Username and PPPoE Password to (as
shown in Figure 3-6).
Click Advanced Config, select Bridging, and then click Enable for
Bridge Function as shown in Figure 3-4. In the Bridging Parameter
window, enter the IP Address (default is 192.168.2.1) and Subnet
Mask (default is 255.255.255.0) that are suitable for your network
domain. After that, click FINISH at the bottom of this page to complete
the modification of this page.
Hint: Ask your ISP for the correct settings.
Figure 3-4
Figure 3-5
16
17
Figure 3-7
Figure 3-6
3.
Click Basic Config, select Interface (as shown in Figure 3-7) and in
this page, you can click radio button and enter MODIFY to choice
which one that you want to change it (as shown in Figure 3-8).
In interface 1, Make sure this wireless interface status is Active, enter
the Wireless interface IP (default is 192.168.1.1) and Wireless
interface Net Mask (default is 255.255.255.0) that are suitable for
your wireless network.
In interface 2, Make sure this Ethernet interface status is Active, and
specify the Ethernet IP address (default is 192.168.2.1) and Ethernet
Net Mask (default is 255.255.255.0) of the Ethernet interface.
In interface 3, Make sure this PPPoE interface status is Active, and
specify the Ethernet IP address (default is 192.168.3.1) and Ethernet
Net Mask (default is 255.255.255.0), choice the ISP index that your
are configured in step 1. After that, follow the default setting and Click
the OK button to return to the Interface Parameter window. Finally, you
need to click FINISH at the bottom of this page to complete the
modification of this page.
Figure 3-8
18
19
Hint1: Make sure interface 4 within status Disable.
Hint2: Choice the NAT (PAT) in every interfaces to enable NAT
service. For example, make sure PPPoE interface within NAT
(PAT) On and others are Off, it means that every
communications through the PPPoE interface needs NAT
transfer.
4.
The AP supports PPPoE auto dial-up, please make sure your default
route is zero. In here, click Basic Config, and then select System as
shown in Figure 3-9. In the System Setup page, specify the Default
Route (Default is 192.168.2.254) is 0.0.0.0 and then click FINISH
button at the bottom of this page to complete the modification of this
page.
Figure 3-10
Figure 3-9
5.
Click Basic Config, select DHCP (as shown in Figure 3-10) and make
sure the DHCP client service is in Disable. After that, click FINISH at
the bottom of this page to complete the modification of this page.
20
21
3.2.3 Configure the AP as a Router with dynamic IP
address Ethernet
3.2.4 Configure the AP as a Router with static IP address
Ethernet
Configure TCP/IP parameters
Configure TCP/IP parameters
1.
Click Advanced Config, select Bridging, and then click Disable for
Bridge Function as shown in Figure 3-4. After that, click FINISH at
the bottom of this page to complete the modification of this page.
1.
Click Advanced Config, select Bridging, and then click Disable for
Bridge Function as shown in Figure 3-4. After that, click FINISH at
the bottom of this page to complete the modification of this page.
2.
Click Basic Config, select Interface (as shown in Figure 3-7), in this
page, you can click radio button and enter MODIFY to choice which
interface that you want to change it (as shown in Figure 3-8).
2.
Click Basic Config, select DHCP (as shown in Figure 3-10) and make
sure the DHCP client service is Disable. After that, click FINISH at the
bottom of this page to complete the modification of this page.
In interface 1, Make sure this wireless interface status is Active, enter
the Wireless interface IP (default is 192.168.1.1) and Wireless
interface Net Mask (default is 255.255.255.0) that are suitable for
your wireless network.
3.
Click Basic Config, select Interface (as shown in Figure 3-7), In this
page, you can click radio button and enter MODIFY to choice which
interface that you want to change it(as shown in Figure 3-8).
In interface 2, Make sure this Ethernet interface status is Active, and
other parameters will obtain automatically by DHCP from your network
environment.
In interface 1, Make sure this wireless interface status is Active, enter
the Wireless interface IP (default is 192.168.1.1) and Wireless
interface Net Mask (default is 255.255.255.0) that are suitable for
your wireless network.
Click the OK button to return to the Interface Parameter window.
Finally, you need to click FINISH at the bottom of this page to complete
the modification of this page.
In interface 2, Make sure this Ethernet interface status is Active, and
specify the Ethernet IP address (default is 192.168.2.1) and Ethernet
Net Mask (default is 255.255.255.0) of the Ethernet interface.
Hint1: Make sure interface 3 and 4 within status: Disable.
Click the OK button to return to the Interface Parameter window.
Finally, you need to click FINISH at the bottom of this page to complete
the modification of this page.
Hint2: In order to enable NAT service, choice the NAT (PAT) in the
interface Wireless and Ethernet. For example, make sure
Ethernet interface within NAT (PAT) On and Wireless
interface is NAT (PAT) Off, it means that every
communication through the Ethernet interface needs to do
NAT transfer.
3.
Click Basic Config, select DHCP (as shown in Figure 3-10) and apply
the DHCP client service running on interface 2 (Ethernet interface),
After that, click FINISH at the bottom of this page to complete the
modification of this page.
Hint1: Make sure interface 3 and 4 within status: Disable.
Hint2: In order to enable NAT service, choice the NAT (PAT) in the
interface Wireless and Ethernet. For example, make sure
Ethernet interface within NAT (PAT) On and Wireless
interface is NAT (PAT) Off, it means that every
communication through the Ethernet interface needs to do
NAT transfer.
4.
Click Basic Config, and then select System as shown in Figure 3-9.
In the System Setup page, specify the Default Route (Default is
192.168.2.254) as the IP Address of the ADSL/Cable modem
connected to the AP or the IP Address of the Gateway in your LAN
environment, and Specify at least one IP address of the DNS
parameter (Default DNS server 1 is 192.168.2.254) provided by your
22
ISP in the DNS server parameter and then click FINISH button at the
bottom of this page to complete the modification of this page.
23
3.3
Configure Wireless related parameters
Configure IEEE 802.11b WLAN parameters (as shown in Figure 3-11)
Click Basic Config, select Wireless LAN page. In here, enter the Channel
(default is 1), rts Threshold (default is 250), frag Threshold (default is
1600), SSID (default is wireless) and Station Name (default is ap) that are
suitable for your radio network and then you can clicked radio button to
disable WEP or enable 64/128 bit WEP services (default is disable), if
WEP is enabled, you must input corresponded Default Key index and
WEP Key. After that, click FINISH at the bottom of this page to complete
the modification of this page.
Figure 3-11
24
3.4
Security
25
3.4.4 IEEE 802.1x Access Control
You can configure Authenticator on AP:
3.4.1 WEP encryption
1.
Click Basic Config, select Wireless LAN page, and configure it to
disable or enable 64/128 bit WEP services (default is Disable) as
shown in Figure 3-11.
2.
Key-in the WEP Key and specify which WEP Key id you want to use it.
After that, click FINISH at the bottom of this page to generate the real
WEP key complete the modification of this page.
1.
Click Basic Config, select 802.1x Access Control page, and choice
the IEEE 802.1x services is Enable or Disable (as shown in Figure 312).
Hint: If you enable WEP services on AP, all of the communication
between stations to AP will be encrypted. You must make sure all
wireless clients with the same WEP key.
3.4.2 Hide the SSID
Click Basic Config, select Wireless LAN page, and click Yes or No to
choose enable/disable the Hide SSID function on this wireless page
(default is No), as shown in Figure 3-11.
Hint: If you enable Hide SSID on AP, all of the client stations must to
specify the SSID of this AP, otherwise your client stations can’t see
(survey) this AP if using any Site Survey tools.
Figure 3-12
3.4.3 Deny ‘ANY’ client station
2.
Click Basic Config, select Wireless LAN page, and click Yes or No to
choose enable/disable the Deny ‘ANY’ function on this wireless page
(default is No), as shown in Figure 3-11.
The AP supporting authentication which based on two kinds of user
information base, Local User Database or Remote Radius Servers.
You can specify which user database you want to use.
3.
You can specify the username/password of an accessible 802.1x
user. All user information entries in the Local User Database are
permitted to connect to the AP. You can also click ADD, DELETE,
MODIFY button to maintain this User Information table.
4.
Some Radius server implements EAP authentication, like Microsoft
Windows 2000 server or Cisco ACS. To set up the Radius server and
AP for authentication, you must specify the Radius server IP address,
Share key between AP and Radius server, authentication port and
accounting port on this Radius server.
Hint: If you enable Deny ANY on AP, all of the client stations can’t use
the well define SSID keyword ‘ANY’ or ‘any’.
26
5.
Click FINISH at the bottom of this page to complete the modification of
this page.
3.4.5 MAC based Access Control
1.
2.
Click Basic Config, select MAC Filter page, and choice the MAC Filter
services is Enable or Disable (as shown in Figure 3-13).
You can specify the MAC address of a wireless client station. All MAC
entries in the MAC address table are permitted to connect to the AP.
You can also click ADD, DELETE, MODIFY button to maintain this
MAC address table. After that, click FINISH at the bottom of this page
to complete the modification of this page.
27
3.5
Configure DHCP server
Sometimes, the operator want to managing a large TCP/IP network
requires maintaining accurate and up-to-date IP address and domain name
information. In this situation, it needs manually configure and enable the
DHCP server service.
1.
Click Basic Config, select DHCP (as shown in Figure 3-10) and
Enable the DHCP server service (Default is Disable).
2.
Specify the DHCP server parameters (Assign Gateway, Assign
Subnet Mask, Assign DNS server, DHCP Start IP address, DHCP
End IP address and Apply Interface) to allow any DHCP client to
acquire the IP information.
Assign Gateway: Configure the default router for the client.
Assign Subnet Mask: Configure the subnet for the client.
Assign DNS Server: Configure the DNS servers IP for the client.
DHCP Start IP address, DHCP End IP address: Configure the DHCP
IP address pool for the client.
Apply Interface: Enable DHCP server service on Wireless or Ethernet
interface.
3.
After that, click FINISH at the bottom of this page to complete the
modification of this page.
Hint: The operator must to configure correct network settings in
Gateway and DNS server of your wireless stations / Ethernet clients to
surf the Internet.
Figure 3-13
28
29
Service Name: Alias name of this internal server, such as FTP.
3.6
Configure Virtual Server
Access Interface: Indicate the translation occurs on which interface
(Wireless interface, NO. 1/Ethernet interface, NO. 2), such as NO. 2.
Sometimes, the operator can expose the internal servers on the local
intranet to the public Internet. For this, you must create the Virtual Server
Mapping for these invisible internal servers.
Protocol: Indicate which protocol (TCP/UDP) you want to translate
from outside to internal server, such as TCP.
1.
Public Access Port number: Indicate which socket port (1 ~ 65535)
you want to translate from outside to internal server, such as 21.
Click Basic Config, select Server Mapping (as shown in Figure 3-14)
and click ADD, DELETE or MODIFY button to change to configure
Virtual Server Mapping page (as shown in Figure 3-15). In this page,
you can maintain this Virtual Server Mapping pool (Default Virtual
Server Mapping pool is empty) to enable the internal servers.
Virtual Server IP address: Specify the private IP address of the
internal server, such as 192.168.1.100.
Virtual Server Port number: Specify the socket port (1 ~ 65535) of the
internal server, such as 21.
3.
After that, click FINISH at the bottom of PAT page to complete the
modification for the Virtual Server Mapping.
Figure 3-14
2.
In configure Virtual Server Mapping page, you must specify some
parameters (Service Name, Protocol, Public Access Interface,
Public Access Port number, Virtual Server IP address and Virtual
Server Port Number) to allow Internet user to access the Internal
servers.
Figure 3-15
30
3.7
Configure Routing Table
1.
Click Advence Config and select the Static Route page. This page
(as shown in Figure 3-16) will present the current configuration for the
routing table. You can also click ADD, DELETE or MODIFY button to
maintain the Static Routing table (Default Routing table only contain
single routing entry: Default Route entry).
2.
Every Route entry contains three parameters: Network Address,
Subnet Mask and Gateway.
31
3.8
1.
Click Advence Config and select the Bridging, and then click Enable
for Bridge Function as shown in Figure 3-4. In the Bridging
Parameter window, enter the IP Address (default is 192.168.2.1) and
Subnet Mask (default is 255.255.255.0) that are suitable for your
network domain.
2.
You can specify the MAC address of a Wireless/Ethernet client. All
MAC entries in the MAC address table are Permitted/Blocked/Learning
to connect to the AP. In here, you can also click ADD, DELETE,
MODIFY button to maintain this MAC address table.
3.
After that, click FINISH at the bottom of this page to complete the
modification of this page.
Network Address and Subnet Mask: Specify the destination network.
Gateway: Indicate the forward gateway.
3.
After that, click FINISH at the bottom of this page to complete the
modification of this page.
Hint: The operator must to configure correct routing settings
following the network infrastructure.
Figure 3-16
Configure Bridge
32
3.9
1.
33
Configure SNMP
Click Advence Config and select the SNMP Community page. This
page (as shown in Figure 3-17) will present the current accessible
SNMP communities and correspond Read/Write privilege. After that,
click FINISH at the bottom of this page to complete the modification of
this page.
Figure 3-18
Figure 3-17
2.
Click Advence Config and select the SNMP Trap page (as shown in
Figure 3-18). In this page, you can specify the SNMP Trap host and
correspond SNMP Trap Community in this page. After that, click
FINISH at the bottom of this page to complete the modification of this
page.
34
35
3.10 Configuration Review and Apply the New
Settings
1.
Click Basic Config or Advence Config and select the Configuration
Review page. This page (as shown in Figure 3-19) will present the
current configuration settings the operator has made.
2.
Click Basic Config or Advence Config and select the Save & Restart
page. In this page (as shown in Figure 3-20), you can click the SAVE
button to apply the new configuration settings and click the Restart
button to take effect the previous configuration changes.
Hint: It needs to take about 10 seconds for the AP to complete the
restart process.
Figure 3-20
Figure 3-19
36
37
3.11.2 Software Upgrade
3.11 Utility
3.11.1 System Info
1.
Click Utility, select Software Upgrade page (as shown in Figure 322), and then you can use TFTP to upgrade your AP. In here, you must
specify the TFTP server IP and select which file you want to upgrade it
(Program image, Web image), then click OK button to start the TFTP
upgrade process.
2.
If the upgrade process is success, the AP will apply the new settings
and start rebooting right away.
Click Utility, select System Info page (as shown in Figure 3-21), you can
view some system information on this, such as Model Name, Software
Version, CPU and RAM, …etc.
Hint: You must set up a TFTP server and this server must contain one
newest image.
Figure 3-21
Figure 3-22
38
39
2.
Chapter 4. Telnet Configuration
The AP is designed to operate as shipped from the factory without any
special set-up. However, it has many options and parameters that can be
changed if users have special requirements. Most of the management
functions can be accessed using TCP/IP protocol, it also configured by
Telnet/Console.
In the Telnet window, enter the User Name and User Password as
shown in Figure 4-2 (default User Name and User Password is user1
and test) to see the main screen of Telnet user interface as shown in
Figure 4-3.
The operator can have to configure the AP through using a Telnet
session on a wired LAN attached computer. To use the Telnet
session, you can simply open a Telnet window using the IP address
that has been assigned to the AP.
1.
Click Start button, select Run to open the Run dialog box. Enter telnet
192.168.2. 1(default terminal type of Telnet is VT100, default IP
address of the AP is 192.168.2.1). Then click OK as shown in Figure
4-1.
Figure 4-2
Figure 4-1.
Figure 4-3
40
3.
The structure of menu tree is shown in Figure 4-4. Users can use the
following keys to select the parameter you want to change or add. The
definition of the parameters is described in Table 4-1 to Table 4-14.
41
Su
Setup
System
Up/Down or i/k key: move the cursor up/down to the specific
item.
Ian
Right or l or Enter key: select the item or enter to sub-menu.
Address <ip> <netmask>
Attrib <Enable | Disable> <Global | Virtual>
Bridge <Enable | Disable>
Left or j key: return to previous menu page.
Home or Ctrl-A: move the cursor to the first item of the menu
page.
Wan
Address <ip> <netmask>
link - Type <Disable | Ethernet | PPP | PPPoE>
Attrib <Enable | Disable> <Global | Virtual>
ether_interface <interface>
Bridge <Enable | Disable>
ISP <ISP Index> <idle disconnect time> <Dial priority>
End or Ctrl-E: move the cursor to the last item of the menu
page.
Ctrl-Q or F1: Show the help page.
PPP
Hint 1: * denote the function is displayed after enable configuration
mode is enabled.
Hint 2: In item su, type default password root to enter the supervisor
configuration mode.
Peer_address <ip>
User_profile <name> <pass_set0>
ISP
*ISP_ profile <ISP name> <ISP destination>
*account - profile <Access account> <Passwd>
Configuration <name> <pass_conf> <ip>
Upgrade
image <ip> <file>
webimage <ip> <file>
bootstrap 2 <ip> <file>
*Enable
Monitor
Wan (CR)
Config_access [Generic| Profile | Pool]
Passwd <pass_conf>
*System
OP _ mode <Router | Bridge | Host>
hostname <name>
default _ route <ip>
Figure 4-4
42
43
*Interface
lan
*ISP
1
address <ip> <netmask>
link type <Disable | Ethernet>
attrib <Disable | Enable> <Global | Virtual>
bridge <Disable | Enable>
1
2
2
address <ip> <netmask>
link type <Disable | Ethernet>
attrib <Disable | Enable> <Global | Virtual>
bridge <Disable | Enable>
3
4
wan
1
address <ip> <netmask>
link type <Disable | Ethernet | PPP | PPPoE>
attrib <Disable | Enable> <Global | Virtual>
bridge <Disable | Enable>
ether_interface <interface>
ISP <ISP Index> <dialup timeout> <Dial priority>
isp - profile (ISP name) (destination string)
account - profile (name) (pass - set 1)
isp - profile (ISP name) (destination string)
account - profile (name) (pass - set 1)
isp - profile (ISP name) (destination string)
account - profile (name) (pass - set 1)
isp - profile (ISP name) (destination string)
account - profile (name) (pass - set 1)
*IP _ share
pat
add
protocol <TCPIUDP>
port <1~65534>
interface <1~2>
server <ip> <1~65534>
name <name>
2
address <ip> <netmask>
link type <Disable | Ethernet | PPP | PPPoE>
attrib <Disable | Enable> <Global | Virtual>
bridge <Disable | Enable>
ether_interface <interface>
ISP <ISP Index> <Idle disconnect time> <Dial priority>
dalete <1~10>
modify (10)
protocol <TCPIUDP>
port <1~65534>
interface <1~2>
server <ip> <1~65534>
name <name>
*PPP
User_edit
modify (5)
profile <name> <pass_set0>
delete
address_pool
nat
local
ip_pool <ip> <1~127>
authenticate <Userpool | RADIUS> <Userpool | RADIUS>
assign_address <Address_Pool | RADIUS> <Address_Pool | RADIUS>
range <1~5> <ip> <1~253>
delete <1~5>
global
range <1~5> <ip> <1~253>
interface <1~5> <1~5>
delete <1~5>
fixed
modify <1~128> <ip> <ip>
interface <1~128> <1~5>
delete <1~128>
Figure 4-4
Figure 4-4
44
45
*dhcp
modify (20)
mac _ address <mac>
lan1_ port <Filter | Forward | Dynamic>
lan2 _ port <Filter | Forward | Dynamic>
wan 1 _ port <Filter | Forward | Dynamic>
wan 2 _ port <Filter | Forward | Dynamic>
generic
service <Disable | Enable>
interface <1~2>
gateway <ip>
netmask <netmask>
ip range <ip> <number>
name server 1 <ip>
name server 2 <ip>
name server 3 <ip>
fixed
stp
module <Disable | Enable>
bridge <number>
lan _ port <1~2> <Disable | Enable> <number>
wan _ port <1~2> <Disable | Enable> <number>
add <mac> <ip>
delete
*snmp
activate _ stp <CR>
community (5)
edit <Disable | Enable> <string> <Read_Only | Read_Write | Denied>
delete
trap (5)
edit <Disble | 1 | 2> <ip> <string>
delete
*tftp <ip> <file>
WLAN
channel <1~14>
weprequired <Disable | Enable>
rts Threshold <0~3000>
frag Threshold <256^2346>
SSID <string>
station Name <string>
defaultkeyId <1~4>
defaultkeys <1~4> <hex>
Figure 4-4
*bridge
generic <Disable | Enable> <ip> <netmask>
static
add
mac _ address <mac>
lan1_ port <Filter | Forward | Dynamic>
lan2 _ port <Filter | Forward | Dynamic>
wan 1 _ port <Filter | Forward | Dynamic>
wan 2 _ port <Filter | Forward | Dynamic>
delete (1~20)
Figure 4-4
46
47
Chapter 5. Specifications
configuration
max _ user <1~5>
telnet_port <1~65534>
console _ port <com 1 | com 2 >
user _ profile
General
Compatibility
Regulation Certifications
add
attrib <13~30><command | Menu><VT100 | ANSI | LINUX | XTerm>
source <-1~10>
profile <name> <pass _ conf> <Level 1 | Level 2 | Level 3 | Unlimited>
delete (1~5)
attrib <13~30><command | Menu><VT100 | ANSI | LINUX | XTerm>
source <-1~10>
profile <name> <pass _ conf> <Level 1 | Level 2 | Level 3 | Unlimited>
Power Supply
Temperature Range
Humidity (non-condensing)
Surge Arrester
Fully interoperable with IEEE802.11b
compliant products
FCC Part 15, ETSI 300/328
Output: –48 VDC/0.7A (power over
Ethernet)
Input: 100/240 VAC; 50/60 Hz
-20 to 70 ℃ (operating)
-40 to 80 ℃ (storage)
5% to 95% typical
20KA Surge Current
modify
attrib <13~30><command | Menu><VT100 | ANSI | LINUX | XTerm>
source <-1~10>
profile <name> <pass _ conf> <Level 1 | Level 2 | Level 3 | Unlimited>
legal - address
modify <1~10> <ip>
delete <1~10>
Radio
Frequency Band
Radio Type
Modulation
*Show: Show the current configuration values
interface
PPP
ip _ share
dhcp
snmp
bridge
isp
run
Operation Channels
RF Output Power
RF Connector
2.4 – 2.484 GHz
Direct Sequence Spread Spectrum
(DSSS)
CCK (11, 5.5Mbps)
DQPSK (2Mbps)
DBPSK (1Mbps)
11 for North America, 14 for Japan,
13 for Europe, 2 for Spain, 4 for France
19dBm typically
Proprietary N-type (Reverse Polarity)
Network Information
*reset - default
Ethernet Interface
IP Sharing
Roaming
write
Security
10-Base T (RJ45)
Supports NAT
Seamless roaming (IEEE802.11b
compliant)
64/128-bit WEP data encryption
reboot
Management
su
sys info
Ping <ip> [1~65534| - t] [1~1999]
exit
Figure 4-4
Local Configuration
Remote Configuration
Firmware Upgrade
IP Auto-configuration
RS-232 serial port
HTTP, Telnet, SNMP
Upgrade via Serial Interface or TFTP
Supports DHCP server
Physical Specifications
Dimensions
245(L) mm x 200(W) mm x 70(H) mm
48
Weight
2100 g
49
50
51
or telnet program on a LAN
Chapter 6.
Default Settings
attached computer.
B-1 Basic Configuration
B-1-1 System (as shown in Table B-1)
Net Mask
Parameter
Description
Supervisor ID
Supervisor’s identity code
root
Supervisor Password
Supervisor’s password
root
Password Confirm
Confirm the password again
root
Host Name
Host name for the AP
Domain Name
Default Route IP
Address
Domain name for the AP
Default Value
HWLAN
NAT(PAT)
DNS Server 2 Address
No.2:255.255.255.0
sub-networks and simplify
No.3:255.255.255.0
routing and data transmission
No.4:255.255.255.0
OFF <-> ON: NAT enable
ON <-> ON: NAT disable
OFF <-> OFF: NAT disable
Shows the corresponding
192.168.2.254
Bridging
interface that joins to form a
bridge
DNS Server Parameter
DNS Server 1 Address
that help divide a network into
function.
domain.com
filtering
No.1:255.255.255.0
Select the network type for NAT
IP address of the gateway for
default route when TCP/IP
Consists of four sets of digits
IP addresses of the DNS
Servers of your Local ISP
192.168.2.254
ISP Index
DNS Server 3 Address
No.1: OFF
No.2: OFF
No.3: ON
No.4: OFF
No.1: Not Join
No.2: Not Join
No.3: Not Join
No.4: Not Join
Select the ISP index given in
the ISP pool
ISP1
Select IP Control Protocol
Table B-1
IPCP
(Static or dynamic) for
Dynamic
PPP/PPPoE interface
B-1-2 Interface (as shown in Table B-2)
Parameter
Description
Idle Time Out (min)
Default Value
Dial Priority
Note:
Interface No.
No.1 Wireless Interface
1. No.3 is effective
No.2 Ethernet Interface
only when No.2 is
No.3 PPPoE Interface
No.4 PPP Interface
Status
Corresponding interface
IP address of the corresponding
interface. The user can use a
IP address
LAN attached (wired or wireless)
computer to configure the AP
through using a web browser
Set the dial-up priority of the
corresponding interface
function of the corresponding
Dial-in Authentication
Selects the authentication
protocol for the corresponding
No.2: 192.168.2.1
No.3: 192.168.3.1
No.4: 192.168.4.1
PPPoE: 3
PPP: 2
Disable
interface
dial-in interface
Table B-2
No.1: 192.168.1.1
3min
Enable or disable the dial-in
2. Default No.3 &
Active
within this period
Dial-in
Active.
No. 4 is Disable
Enable or disable the
Cancel the dial if not connected
None
52
53
B-1-5 DHCP (as shown in Table B-5)
B-1-3 Telnet/Console (as shown in Table B-3)
Parameter
Description
Parameter
Maximum User
the users that can login the AP
through Telnet session at the
DHCP Client Setting
2
Console Port
Program
The communication port that is
used to login the AP
ID Number
Index for Telnet users
User Name
User name for Telnet session
Privilege
Max. Screen Line
Select the user’s privilege level
for Telnet session
Set the maximum number of
lines displayed on the screen
Telnet session
Select the type of the keyboard
for Telnet session
Default Gateway
COM1
Net Mask
Unlimited
24
Menu
that help divide a network into
sub-networks and simplify
ISP Name
Name of Internet Service
Provider
routing and data transmission
IP address of the DNS host
192.168.2.254
DHCP Start IP
IP starting address
192.168.1.240
DHCP End IP
IP ending address
192.168.1.254
Interface
Select the interface to provide
DHCP service
Phone Number
Note: The phone number must
enter direct line phone number
Fixed Host Entry
address mapping to limit the
client station with the Ethernet
address to get the IP address
Table B-5
Default Value
ISP-1
B-1-6 Virtual Server Mapping (as shown in Table B-6)
12345678
Parameter
Service Name
Username
The user name used to login ISP
user
Password
The password used to login ISP
pass
Table B-4
HWLAN
Define a fixed Ethernet-to-IP
VT100
The phone number that is used
to dial up your ISP
255.255.255.0
Name Server
B-1-4 Telnet/Console (as shown in Table B-4)
Description
192.168.1.1
Consists of four sets of digits
1
user1
default route when TCP/IP
filtering
Table B-3
Parameter
Disable
IP address of the gateway for
(Command/Menu mode)
Keyboard Type
address assignment to wireless
stations
23
Select the type of display for
Show Mode
Disable
Enable or disable automatic IP
Trigger DHCP Service
The port number for Telnet
interface to obtain an IP address
automatically
same time
Telnet Port
Default Value
Enable or disable the specified
Default Value
Set the maximum number of
Description
Protocol
Public Access –
Description
Specify the service for public
access
Select a protocol for public
access
Select an interface for public
Default Value
NULL
NULL
NULL
54
55
B-1-8 Wireless LAN (as shown in Table B-8)
Interface
access
Public Access – Port
Specify the port number of the
Number
interface for public access
Virtual Server – IP
Specify the IP address of the
Address
virtual server
Virtual Server – Port
Specify the port number of
Number
internal virtual server
NULL
Parameter
Regulatory Domain
NULL
Channel
NULL
RTS Threshold
Table B-6
B-1-7 NAT (Network Address Translation) (as shown in Table B7)
Parameter
Description
Local IP Address
IP starting address of local IP
Pool – Base IP Address address
Local IP Address
Pool –Count
Global IP Address
Number of local IP address
IP starting address of global IP
Pool – Count
Number of global IP address
Global IP Address
Specify the interface as global
Pool – Interface
IP address
Fixed IP Address
Define a local and global IP
Mapping – Local/Global address pair for network
IP Address
address translation
Fixed IP Address
Specify the interface for
Mapping – Interface
network address translation
Table B-7
Which this NIC may be deployed
The operating radio frequency
channel for the AP
Set RTS (Request To Send)
threshold value
Set fragmentation threshold
Threshold
value
Default Value
1
11
250
1600
Wireless LAN service area
SSID
identifier of the AP (case
wireless
sensitive)
NULL
NULL
Define the regulatory domain to
Fragmentation
Station Name
Pool – Base IP Address address
Global IP Address
Default Value
Description
Shows the name of the AP
ap
Enable or disable 64-bit WEP
WEP
(Wired Equivalent Privacy) key
Disable
to encrypt data
NULL
NULL
Select a WEP key to encrypt
Default Key
each frame transmitted from
the radio using one the of the
Keys from the Key Panel
When you use WEP to
NULL
communicate with the other
wireless clients, all the wireless
NULL
devices in this network must
have the same encryption key
NULL
Key Panel
or pass phrase.
Note: each key must consist
of hex digits, it means that
only digit 0 -9 and letters A-F
are valid entries. If entered
incorrectly, program will not
write keys to a driver.
Table B-8
1
56
B-1-9 Bridging (as shown in Table B-9)
Parameter
Bridging Function
Description
Enable or disable bridging
57
B-1-10 SNMP Community (as shown in Table B-10)
Default Value
Parameter
Enable
Function
Enable or disable the function
Validity
IP Address of the AP when in
192.168.2.1
Access Right
wireless) computer to configure
Community
LAN attached computer.
Manager
B-1-11 SNMP Trap (as shown in Table B-11)
sub-networks and simplify
mode
Parameter
Enable
Enable
Interface
Index
Disable
Disable
MAC Address
Table B-10
that help divide a network into
Enable or disable the operation
MAC address to be considered
00-00-00-00-00-00
1.
Filter
frames), Forward(always
2.
Filter
forward the frames) or
3.
---
Dynamic(forward the frames if
4.
---
Table B-9
Enable or disable the activity of
Version
Default Value
Enable
the corresponding community
Version1
Version
Version 1: MIB1
Version 2: MIB2
Select Filter(always block the
corresponding interface
Description
Select or disable the SNMP
in forward/filter policy
the MAC address exists) to the
Public
(public or private) for SNMP
255.255.255.0
routing and data transmission
Operation mode
(Deny/Read/Write/Create) for
Specify the type of community
browser or telnet program on a
Subnet Mask
Read
SNMP Manager
the AP through using a web
Consists of four sets of digits
Enable
of the corresponding community
Select the access right
use a LAN attached (wired or
Default Value
index
Bridging mode. The user can
IP Address
Description
Specify the IP address of the
IP Address
192.168.2.100
SNMP Manager for SNMP Trap
Report
Specify the type of community
Community
(public or private) for SNMP
Manager
Table B-11
Public
58
59
B-1-12 Software Upgrade (as shown in Table B-12)
Parameter
TFTP Server IP
Address
Description
Default Value
Specify the IP address of the
192.168.2.100
TFTP server to upgrade the
firmware of the AP
Specify the filename of
Upgrade Filename
requested firmware
stored in TFTP server
Table B-12
soho.bin
Chapter 7. Regulatory Compliance Information
Radio Frequency Interference Requirements
This device complies with Part 15 of FCC Rules and Canada RSS-210.
Operation is subject to the following conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference
that may cause undesired operation.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20 cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna of transmitter.
Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules and Regulation.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to
nearby TV’s, VCR’s, radio, computers, or other electronic devices. To
minimize or prevent such interference, this equipment should not be placed
or operated near these devices. If interference is experienced, moving the
equipment away from them will often reduce or eliminate the interference.
However, there is no guarantee that interference will not occur in a
particular installation. If the equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
60
Professional Installation
Per the recommendation of the FCC, the installation of high gain directional
antenna to the system, which are intended to operated solely as a point-topoint system and whose total power exceeds +30dBm EIRP, require
professional installation. It is the responsibility of the installer and the end
user that the high power systems are operated strictly as a point-to-point
system.
Systems operating as a point-to-multipoint system or use non directional
antennas cannot exceed +30dBm EIRP power requirement under any
circumstances and do not require professional installation.
Information to User
The user manual or instruction manual for an intentional or unintentional
radiator shall caution the user that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement