Toro Universal Swivel Auger Head, Compact Tool Carrier Compact Utility Loaders, Attachment Operator's Manual

Toro Universal Swivel Auger Head, Compact Tool Carrier Compact Utility Loaders, Attachment Operator's Manual
Form No. 3430-902 Rev A
Auger Head
Compact Tool Carrier
Model No. 22805—Serial No. 404320000 and Up
Model No. 22806—Serial No. 404320000 and Up
Register at www.Toro.com.
Original Instructions (EN)
*3430-902* A
Important: With your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty, parts, and other
product information.
This product complies with all relevant European
directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
WARNING
CALIFORNIA
Proposition 65 Warning
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
Introduction
The auger is a hydraulically powered attachment
intended to be used on a Toro compact tool carrier.
It is designed primarily to dig vertical holes in the
earth for the installation of posts, plants, and other
construction and landscaping needs. Using this
product for purposes other than its intended use could
prove dangerous to you and bystanders.
g244284
Figure 1
1. Model and serial number location
Model No.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.
Serial No.
This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(Figure 2), which signals a hazard that may cause
serious injury or death if you do not follow the
recommended precautions.
Visit www.Toro.com for product safety and operation
training materials, accessory information, help finding
a dealer, or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.
g000502
Figure 2
1. Safety-alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
2
Contact us at www.Toro.com.
Printed in the USA
All Rights Reserved
Safety
Contents
Safety ....................................................................... 3
General Safety ................................................... 3
Slope Safety ....................................................... 4
Auger Safety....................................................... 4
Maintenance and Storage Safety........................ 4
Safety and Instructional Decals .......................... 5
Product Overview ..................................................... 5
Specifications .................................................... 5
Operation .................................................................. 6
Installing and Removing the Attachment ............. 6
Installing an Auger .............................................. 6
Digging a Hole .................................................... 8
Removing an Auger ............................................ 8
Transport Position .............................................. 9
Maintenance ........................................................... 10
Recommended Maintenance Schedule(s) ........... 10
Greasing the Cradle Arm Pivot Points ............... 10
Changing the Planetary Gear Case
Oil ................................................................. 10
Storage ....................................................................11
Troubleshooting ...................................................... 12
DANGER
There may be buried utility lines in the work
area. Digging into them may cause a shock
or an explosion.
Have the property or work area marked for
buried lines and do not dig in marked areas.
Contact your local marking service or utility
company to have the property marked (for
example, in the US, call 811 or in Australia,
call 1100 for the nationwide marking service).
General Safety
Always follow all safety instructions to avoid serious
injury or death.
• Always transport the attachment close to the
ground; refer to Transport Position (page 9).
• Have the property or work area marked for buried
lines and other objects, and do not dig in marked
areas.
• Read and understand the content of this Operator’s
Manual before starting the engine.
• Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur.
• Never allow children or untrained people to
operate the machine.
• Keep your hands and feet away from the moving
components and attachments.
• Do not operate the machine without the guards
and other safety protective devices in place and
working on the machine.
• Keep bystanders and pets away from the machine.
• Stop the machine, shut off the engine, and remove
the key before servicing, fueling, or unclogging
the machine.
Improperly using or maintaining this machine can
result in injury. To reduce the potential for injury,
comply with these safety instructions and always
pay attention to the safety-alert symbol , which
means Caution, Warning, or Danger—personal safety
instruction. Failure to comply with these instructions
may result in personal injury or death.
3
Slope Safety
Auger Safety
• Operate the machine up and down slopes with
• Keep your hands, feet, and any other part of your
the heavy end of the machine uphill. Weight
distribution changes with attachments. This
attachment makes the front of machine the heavy
end.
body or clothing away from moving auger or other
parts.
• Keep your hands and fingers away from the cradle
arms.
• Keep the attachment in the lowered position
• Use caution when using the auger near fences,
when on slopes. Raising the attachment on a
slope affects the stability of the machine.
ditches, slopes, or other obstacles.
• Tilt the attachment fully rearward so that the
• Slopes are a major factor related to loss of control
auger rests in the cradle when transporting the
attachment with the traction unit.
and tip-over accidents, which can result in severe
injury or death. Operating the machine on any
slope or uneven terrain requires extra caution.
• Always lower the attachment and shut off the
• Establish your own procedures and rules for
machine each time you leave the operating
position.
operating on slopes. These procedures must
include surveying the site to determine which
slopes are safe for machine operation. Always
use common sense and good judgment when
performing this survey.
Maintenance and Storage
Safety
• Slow down and use extra care on hillsides. Ground
conditions can affect the stability of the machine.
• Check fasteners at frequent intervals for proper
tightness to ensure that the equipment is in safe
operating condition.
• Avoid starting or stopping on a slope. If the
machine loses traction, proceed slowly, straight
down the slope.
• Refer to the Operator’s Manual for important
details if you store the attachment for an extended
period of time
• Avoid turning on slopes. If you must turn, turn
slowly and keep the heavy end of the machine
uphill.
• Maintain or replace safety and instruction labels,
• Keep all movements on slopes slow and gradual.
as necessary.
Do not make sudden changes in speed or
direction.
• If you feel uneasy operating the machine on a
slope, do not do it.
• Watch for holes, ruts, or bumps, as uneven terrain
could overturn the machine. Tall grass can hide
obstacles.
• Use caution when operating on wet surfaces.
Reduced traction could cause sliding.
• Evaluate the area to ensure that the ground is
stable enough to support the machine.
• Use caution when operating the machine near the
following:
– Drop-offs
– Ditches
– Embankments
– Bodies of water
The machine could suddenly roll over if a track
goes over the edge or the edge caves in. Maintain
a safe distance between the machine and any
hazard.
• Do not remove or add attachments on a slope.
• Do not park the machine on a hillside or slope.
4
Safety and Instructional
Decals
Product Overview
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
g004514
Figure 3
1. Hose guide
4. Cradle arm
2. Mounting plate
5. Drive head
3. Motor
6. Drive shaft
decal105-0326
105-0326
1. Warning—read the
Operator's Manual.
Specifications
3. Explosion and/or electric
shock hazard—do not dig
in areas with buried gas or
power lines.
Note: Specifications and design are subject to
change without notice.
2. Entanglement hazard,
auger—keep bystanders
away.
Model 22805
decal133-8061
133-8061
Width
62 cm (24 inches)
Length
40 cm (16 inches)
Height
59 cm (23 inches)
Weight
83 kg (182 lb)
Model 22806
Width
62 cm (24 inches)
Length
42 cm (17 inches)
Height
59 cm (23 inches)
Weight
89 kg (196 lb)
To ensure optimum performance and continued safety
certification of the machine, use only genuine Toro
replacement parts and accessories. Replacement
parts and accessories made by other manufacturers
could be dangerous, and such use could void the
product warranty.
5
Operation
CAUTION
Hydraulic couplers, hydraulic lines/valves,
and hydraulic fluid may be hot. If you contact
hot components, you may be burned.
• Wear gloves when operating the hydraulic
couplers.
• Allow the machine to cool before touching
hydraulic components.
• Do not touch hydraulic fluid spills.
Determine the left and right sides of the machine from
the normal operating position.
Installing and Removing
the Attachment
Refer to the Operator’s Manual for the traction unit for
the installation and removal procedure.
Installing an Auger
Important: Before installing the attachment,
position the machine on a level surface, ensure
that the mount plates are free of any dirt or debris,
and ensure that the pins rotate freely. If the pins
do not rotate freely, grease them.
WARNING
The auger head swings freely in the cradle
arms. Your hands or fingers could get
pinched and severely injured or amputated if
they are caught between the cradle arms and
the swinging drive head.
Note: Always use the traction unit to lift and move
the attachment. To move an auger without the drive
head, sling a strap over each end of the auger and
hoist it to the desired location.
Keep your hands and fingers away from the
cradle arms.
WARNING
If you do not fully seat the quick-attach
pins through the attachment mount plate,
the attachment could fall off the machine,
crushing you or bystanders.
1.
2.
Ensure that the quick-attach pins are fully
seated in the attachment mount plate.
WARNING
Hydraulic fluid escaping under pressure can
penetrate skin and cause injury. Fluid injected
into the skin must be surgically removed
within a few hours by a doctor familiar with
this form of injury; otherwise, gangrene may
result.
Park the machine on a level surface and engage
the parking brake (if applicable).
If you are installing an auger on the Model
22806 drive head continue as follows, otherwise
continue to step 3.
A. Lower the loader arms, shut off the engine,
and remove the key.
B. Position the drive head vertically, slide a
bolt (1/2 x 2-1/2 inches) into the holes in the
front cradle arms, and secure it lightly with
a flange nut (1/2 inch) as shown in Figure 4.
C. Continue to step 3.
• Ensure that all hydraulic-fluid hoses
and lines are in good condition and all
hydraulic connections and fittings are tight
before applying pressure to the hydraulic
system.
• Keep your body and hands away from
pinhole leaks or nozzles that eject
high-pressure hydraulic fluid.
• Use cardboard or paper to find hydraulic
leaks; never use your hands.
g004515
Figure 4
1. Drive head (front view)
2. Bolt
6
3. Front cradle arm
3.
Raise the loader arms so that the drive head
clears the ground.
4.
Shut off the engine and remove the key.
5.
Manually rotate the auger drive head up, until
you can slide a bolt (1/2 x 2-1/2 inches) into the
hole in the cradle arm, securing the drive head.
Lightly secure the bolt with a nut (1/2 inch) as
shown in Figure 5.
8.
Maneuver the drive shaft into the end of the
auger shaft or extension (if applicable) as shown
in Figure 7.
g004518
Figure 7
1. Drive head
9.
10.
2. Auger shaft
Shut off the engine and remove the key.
Secure the auger to the drive head with a bolt
(7/8 x 4-1/2 inch) and nut (7/8 inch) as shown
in Figure 8.
g004519
Figure 8
g004516
Figure 5
1. Drive head
1. Bolt (7/8 x 4-1/2 inches)
3. Bolt(s) and nut(s)
2. Nut (7/8 inch)
3. Bolt and flange nut
2. Cradle arm
6.
If using an extension with the auger, insert the
end of the extension into the end of the auger
and secure the auger to the extension with a bolt
(7/8 x 4-1/2 inch) and nut (7/8 inch) as shown
in Figure 6.
11.
Remove the bolts and nuts from the cradle arms
installed in steps 2 (if applicable) and 5.
12.
Start the engine.
13.
Raise the auger free of the ground (Figure 9).
g004517
Figure 6
1. Extension
3. Bolt (7/8 x 4-1/2 inch)
2. Auger
4. Nut (7/8 inch)
g004520
Figure 9
7.
Start the engine.
7
14.
Removing an Auger
When the auger is vertical, tilt the attachment
plate rearward until the drive head contacts the
attachment plate to stabilize the auger and keep
it from swinging freely (Figure 9).
1.
Disengage the auxiliary hydraulics.
2.
Raise the loader arms so the auger comes out
of the hole.
Digging a Hole
Note: If you have a 24-inch extension installed
between the drive head and the auger, you may
need to raise the auger as high as possible and
then move the traction unit backward to pull the
auger the rest of the way out of the hole.
Important: Before digging, ensure that the
ground is free of any trash or debris.
1. Lower the auger to the soil at the site of the
proposed hole.
2. Move the throttle lever to the FAST position.
3. If your traction unit has a speed-selector lever,
move it to the SLOW position.
4. If your traction unit has a flow-divider control,
move it to the 10 o'clock position.
5. Pull the auxiliary hydraulics lever to the operator
grip or reference bar to begin digging.
6. Lower the auger slowly as the soil is loosened.
As you dig deeper, move the traction unit
backward or forward as required to keep the
auger vertical (Figure 10).
g004521
Figure 10
7.
When the auger becomes full of soil, disengage
the auger drive and lift the auger from the hole.
Engage the auger drive to spin off the soil, then
resume digging.
Important: Switching the auxiliary
8.
hydraulics lever rapidly from forward to
reverse will help to shake off the soil.
When you are done digging, allow the auger to
run for a few seconds to clean any loose dirt out
of the hole, shut off the auxiliary hydraulics, and
fully raise the auger out of the hole.
DANGER
If you are using Model 22806, excessive
downward force may cause the bit to wobble
uncontrollably, which could tip the traction
unit. You or bystanders could be pinned or
seriously injured.
Do not use excessive downward pressure on
the bit. Allow the bit to pull itself into the soil.
8
3.
Drive the machine to the storage location for
the auger.
4.
While lowering the arms, drive slowly backward
until the auger is horizontal.
5.
Shut off the engine and remove the key.
6.
Remove the bolt and nut securing the drive head
to the auger or extension.
7.
Start the engine and back the traction unit away
from the auger.
8.
If you used an extension, remove the bolt and
nut securing it and pull it off the auger.
Transport Position
• When transporting an auger smaller than 51 cm
(20 inch) diameter over long distances or slopes,
do the following:
• When transporting any size auger over short
distances or an auger larger than 51 cm (20 inch)
diameter over longer distances, do the following:
1.
Raise the auger so that it clears the ground
and is vertical (Figure 9).
1.
While lowering the arms, drive slowly
backwards until the auger is horizontal, then
engage the parking brake (if applicable).
2.
Shut off the engine and remove the key.
3.
Manually rotate the auger drive head up,
until you can slide a bolt (1/2 x 2-1/2 inches)
into the hole in the cradle arm, securing the
drive head. Lightly secure the bolt with a nut
(1/2 inch) as shown in Figure 5.
4.
As you transport the auger, keep it as close
to the ground as possible, no more than 15
cm (6 inches) above the ground.
g266890
Figure 11
2.
g244918
Tilt the attachment plate rearward until the
drive head contacts the attachment plate to
stabilize the auger and keep it from swinging
freely.
Figure 12
1. No more than 15 cm (6 inches) above the ground
9
Maintenance
Recommended Maintenance Schedule(s)
Maintenance Service
Interval
Maintenance Procedure
After the first 50 hours
• Change the planetary gearcase oil.
Before each use or daily
Every 1,000 hours
Before storage
• Grease the cradle arm pivot points. (Grease all fittings immediately after every
washing.)
• Check the auger teeth and replace them if they are damaged or worn.
• Change the planetary gearcase oil.
• Check the auger teeth and replace them if they are damaged or worn.
• Paint chipped surfaces.
CAUTION
If you leave the key in the switch, someone could accidently start the engine and seriously
injure you or other bystanders.
Remove the key from the switch before you perform any maintenance.
Greasing the Cradle Arm
Pivot Points
Service Interval: Before each use or daily (Grease
all fittings immediately after every
washing.)
Grease Type: General-purpose grease
1.
Park the machine on a level surface, engage
the parking brake (if applicable), and lower the
loader arms.
2.
Shut off the engine and remove the key.
3.
Clean the grease fittings with a rag.
4.
Connect a grease gun to each fitting.
1. Planetary gear case
5.
Pump grease into the fittings until grease begins
to ooze out of the bearings.
2. Bolt
6.
Wipe up any excess grease.
2.
Changing the Planetary
Gear Case Oil
Remove the 4 bolts securing the motor and
remove the motor, allowing all the oil to drain
into the pan.
3.
When the oil is completely drained, turn the
drive head so that the opening is facing the up.
Service Interval: After the first 50 hours
4.
Add oil to the gearcase.
5.
Replace the motor and secure it with the four
bolts removed previously. Torque the bolts to
142 N∙m (105 ft-lb).
g004522
Figure 13
Every 1,000 hours
Type: Mild, extreme pressure lubricant, rated
API-GL-5, number 80 or 90
Capacity: 0.4 L (13.6 fl oz)
1.
Support the drive head over an oil pan (Figure
13).
10
3. Motor
Storage
1.
Before long-term storage, wash the attachment
with mild detergent and water to remove dirt and
grime.
2.
Check and tighten all bolts, nuts, and screws.
Repair or replace any damaged or worn part.
3.
Ensure that all hydraulic couplers are connected
together to prevent contamination of the
hydraulic system.
4.
Paint all scratched or bare metal surfaces.
Note: Paint is available from your Authorized
Service Dealer.
5.
Store the attachment in a clean, dry garage or
storage area. Cover it to protect it and keep it
clean.
11
Troubleshooting
Problem
The drive head does not operate.
Possible Cause
Corrective Action
1. Hydraulic coupler not completely
connected.
1. Check and tighten all couplers.
2. A hydraulic coupler needs to be
replaced.
3. There is an obstruction in a hydraulic
hose.
4. A hydraulic hose is kinked.
5. The gearbox is contaminated.
2. Check the couplers and replace any
that are worn or damaged.
3. Find and remove the obstruction.
12
4. Replace the kinked hose.
5. Refer to your Authorized Service
Dealer.
Notes:
Declaration of Incorporation
The Toro Company, 8111 Lyndale Avenue South, Bloomington, MN, USA declares that the following unit(s)
conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain
Toro models as indicated on the relevant Declarations of Conformity.
Model No.
Serial No.
Product Description
22805
404320000 and Up
Auger Head
22806
404320000 and Up
Universal Swivel Auger Head
Invoice Description
AUGER POWER HEAD
ATTACHMENT CE
SWIVEL AUGER POWER
HEAD ATTACHMENT CE
General Description
Directive
Auger
2006/42/EC
Auger
2006/42/EC
Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.
We will undertake to transmit, in response to requests by national authorities, relevant information on this partly
completed machinery. The method of transmission shall be electronic transmittal.
This machinery shall not be put into service until incorporated into approved Toro models as indicated on the
associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in
conformity with all relevant Directives.
Certified:
Authorized Representative:
Marcel Dutrieux
Manager European Product Integrity
Toro Europe NV
Nijverheidsstraat 5
2260 Oevel
Belgium
Joe Hager
Sr. Engineering Manager
8111 Lyndale Ave. South
Bloomington, MN 55420, USA
February 7, 2019
European Privacy Notice
The Information Toro Collects
Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you
to share certain personal information with us, either directly or through your local Toro company or dealer.
The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies
in your country.
BY SHARING YOUR PERSONAL INFORMATION WITH US, YOU ARE CONSENTING TO THE PROCESSING OF YOUR PERSONAL INFORMATION
AS DESCRIBED IN THIS PRIVACY NOTICE.
The Way Toro Uses Information
Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell
you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not
sell your personal information to any other company. We reserve the right to disclose personal information in order to comply with applicable laws and
with requests by the appropriate authorities, to operate our systems properly or for our own protection or that of other users.
Retention of your Personal Information
We will keep your personal information as long as we need it for the purposes for which it was originally collected or for other legitimate purposes
(such as regulatory compliance), or as required by applicable law.
Toro's Commitment to Security of Your Personal Information
We take reasonable precautions in order to protect the security of your personal information. We also take steps to maintain the accuracy and current
status of personal information.
Access and Correction of your Personal Information
If you would like to review or correct your personal information, please contact us by email at [email protected]
Australian Consumer Law
Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.
374-0282 Rev C
California Proposition 65 Warning Information
What is this warning?
You may see a product for sale that has a warning label like the following:
WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov.
What is Prop 65?
Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into
California. It mandates that the Governor of California maintain and publish a list of chemicals known to cause cancer, birth defects, and/or other
reproductive harm. The list, which is updated annually, includes hundreds of chemicals found in many everyday items. The purpose of Prop 65 is to
inform the public about exposure to these chemicals.
Prop 65 does not ban the sale of products containing these chemicals but instead requires warnings on any product, product packaging, or literature with
the product. Moreover, a Prop 65 warning does not mean that a product is in violation of any product safety standards or requirements. In fact, the
California government has clarified that a Prop 65 warning “is not the same as a regulatory decision that a product is ‘safe’ or ‘unsafe.’” Many of these
chemicals have been used in everyday products for years without documented harm. For more information, go to https://oag.ca.gov/prop65/faqs-view-all.
A Prop 65 warning means that a company has either (1) evaluated the exposure and has concluded that it exceeds the “no significant risk level”; or (2)
has chosen to provide a warning based on its understanding about the presence of a listed chemical without attempting to evaluate the exposure.
Does this law apply everywhere?
Prop 65 warnings are required under California law only. These warnings are seen throughout California in a wide range of settings, including but not
limited to restaurants, grocery stores, hotels, schools, and hospitals, and on a wide variety of products. Additionally, some online and mail order
retailers provide Prop 65 warnings on their websites or in catalogs.
How do the California warnings compare to federal limits?
Prop 65 standards are often more stringent than federal and international standards. There are various substances that require a Prop 65 warning
at levels that are far lower than federal action limits. For example, the Prop 65 standard for warnings for lead is 0.5 μg/day, which is well below
the federal and international standards.
Why don’t all similar products carry the warning?
•
•
Products sold in California require Prop 65 labelling while similar products sold elsewhere do not.
•
•
The enforcement of Prop 65 is inconsistent.
A company involved in a Prop 65 lawsuit reaching a settlement may be required to use Prop 65 warnings for its products, but other companies
making similar products may have no such requirement.
Companies may elect not to provide warnings because they conclude that they are not required to do so under Prop 65; a lack of warnings for a
product does not mean that the product is free of listed chemicals at similar levels.
Why does Toro include this warning?
Toro has chosen to provide consumers with as much information as possible so that they can make informed decisions about the products they buy and
use. Toro provides warnings in certain cases based on its knowledge of the presence of one or more listed chemicals without evaluating the level of
exposure, as not all the listed chemicals provide exposure limit requirements. While the exposure from Toro products may be negligible or well within the
“no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these
warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
Rev A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement