Toro Auger Head, Compact Tool Carrier Compact Utility Loaders, Attachment Operator's Manual

Toro Auger Head, Compact Tool Carrier Compact Utility Loaders, Attachment Operator's Manual
Form No. 3420-731 Rev A
Auger Head and Universal Swivel
Auger Head
Compact Tool Carrier
Model No. 22805—Serial No. 402000000 and Up
Model No. 22806—Serial No. 402000000 and Up
Register at www.Toro.com.
Original Instructions (EN)
*3420-731* A
Important: With your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty, parts, and other
product information.
This product complies with all relevant European
directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical
or chemicals known to the State of
California to cause cancer, birth defects,
or reproductive harm.
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
g244284
Figure 1
Introduction
1. Model and serial number location
The machine is a hydraulically powered auger
attachment for compact tool carriers. It is designed
to dig vertical holes in the earth for the installation of
posts, plants, and other construction and landscaping
needs. It is not intended to drill holes in pavement,
concrete, or ice.
Model No.
Serial No.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.
This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(Figure 2), which signals a hazard that may cause
serious injury or death if you do not follow the
recommended precautions.
You may contact Toro directly at www.Toro.com
for product safety and operation training materials,
accessory information, help finding a dealer, or to
register your product.
g000502
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Figure 2
1. Safety-alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
2
Contact us at www.Toro.com.
Printed in the USA
All Rights Reserved
Safety
Contents
Safety ....................................................................... 3
General Safety ................................................... 3
Slope Safety ....................................................... 4
Auger Safety....................................................... 4
Maintenance and Storage Safety........................ 4
Safety and Instructional Decals .......................... 5
Product Overview ..................................................... 5
Specifications .................................................... 5
Operation .................................................................. 6
Installing and Removing the Attachment ............. 6
Installing an Auger .............................................. 6
Digging a Hole .................................................... 8
Removing an Auger ............................................ 8
Transport Position .............................................. 9
Maintenance ........................................................... 10
Recommended Maintenance Schedule(s) ........... 10
Greasing the Cradle Arm Pivot Points ............... 10
Changing the Planetary Gear Case
Oil ................................................................. 10
Storage ....................................................................11
Troubleshooting ...................................................... 12
DANGER
There may be buried utility lines in the work
area. Digging into them may cause a shock
or an explosion.
Have the property or work area marked for
buried lines and do not dig in marked areas.
Contact your local marking service or utility
company to have the property marked (for
example, in the US, call 811 or in Australia,
call 1100 for the nationwide marking service).
General Safety
Always follow all safety instructions to avoid serious
injury or death.
• Always carry the attachment close to the ground;
refer to Transport Position (page 9).
• Have the property or work area marked for buried
lines and other objects, and do not dig in marked
areas.
• Read and understand the content of this Operator’s
Manual before starting the engine.
• Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur.
• Never allow children or untrained people to
operate the machine.
• Keep your hands and feet away from the moving
components and attachments.
• Do not operate the machine without the guards
and other safety protective devices in place and
working on the machine.
• Keep bystanders and pets a safe distance away
from the machine.
• Stop the machine, shut off the engine, and remove
the key before servicing, fueling, or unclogging
the machine.
Improperly using or maintaining this machine can
result in injury. To reduce the potential for injury,
comply with these safety instructions and always pay
attention to the safety-alert symbol, which means
Caution, Warning, or Danger—personal safety
instruction. Failure to comply with these instructions
may result in personal injury or death.
You can find additional safety information where
needed throughout this Operator’s Manual.
3
Slope Safety
Auger Safety
• Operate the machine up and down slopes with
• For wheeled machines, use the counterweight on
the heavy end of the machine uphill. Weight
distribution changes with attachments. This
attachment makes the front of machine the heavy
end.
the traction unit when using the auger head with a
30 to 76 cm (12 to 30 inch) auger installed.
• For wheeled machines, do not use the
counterweight when using the auger head without
an auger or with an auger smaller than 30 cm (12
inches).
• Keep the attachment in the lowered position
when on slopes. Raising the attachment on a
slope affects the stability of the machine.
• Keep your hands, feet, and any other part of your
• Slopes are a major factor related to loss of control
body or clothing away from moving auger or other
parts.
and tip-over accidents, which can result in severe
injury or death. Operating the machine on any
slope or uneven terrain requires extra caution.
Maintenance and Storage
Safety
• Establish your own procedures and rules for
operating on slopes. These procedures must
include surveying the site to determine which
slopes are safe for machine operation. Always
use common sense and good judgment when
performing this survey.
• Check fasteners at frequent intervals for proper
tightness to ensure that the equipment is in safe
operating condition.
• Refer to the Operator’s Manual for important
• Slow down and use extra care on hillsides. Ground
details if you store the attachment for an extended
period of time
conditions can affect the stability of the machine.
• Avoid starting or stopping on a slope. If the
• Maintain or replace safety and instruction labels,
machine loses traction, proceed slowly, straight
down the slope.
as necessary.
• Avoid turning on slopes. If you must turn, turn
slowly and keep the heavy end of the machine
uphill.
• Keep all movements on slopes slow and gradual.
Do not make sudden changes in speed or
direction.
• If you feel uneasy operating the machine on a
slope, do not do it.
• Watch for holes, ruts, or bumps, as uneven terrain
could overturn the machine. Tall grass can hide
obstacles.
• Use caution when operating on wet surfaces.
Reduced traction could cause sliding.
• Do not operate the machine near drop-offs,
ditches, embankments, or bodies of water. The
machine could suddenly roll over if a wheel or
track goes over the edge or the edge caves in.
Maintain a safe distance between the machine
and any hazard.
• Do not remove or add attachments on a slope.
• Do not park the machine on a hillside or slope.
4
Safety and Instructional
Decals
Product Overview
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
g004514
Figure 3
1. Hose guide
4. Cradle arm
2. Mounting plate
5. Drive head
3. Motor
6. Drive shaft
decal105-0326
105-0326
1. Warning—read the
Operator's Manual.
Specifications
3. Explosion and/or electric
shock hazard—do not dig
in areas with buried gas or
power lines.
Note: Specifications and design are subject to
change without notice.
2. Entanglement hazard,
auger—keep bystanders a
safe distance away from
the auger.
Model 22805
Width
62 cm (24 inches)
Length
40 cm (16 inches)
Height
59 cm (23 inches)
Weight
83 kg (182 lb)
Model 22806
5
Width
62 cm (24 inches)
Length
42 cm (17 inches)
Height
59 cm (23 inches)
Weight
89 kg (196 lb)
Operation
CAUTION
Hydraulic couplers, hydraulic lines/valves,
and hydraulic fluid may be hot. If you contact
hot components, you may be burned.
• Wear gloves when operating the hydraulic
couplers.
• Allow the machine to cool before touching
hydraulic components.
• Do not touch hydraulic fluid spills.
Installing and Removing
the Attachment
Refer to the Operator’s Manual for the traction unit for
the installation and removal procedure.
Important: Before installing the attachment,
position the machine on a level surface, ensure
that the mount plates are free of any dirt or debris,
and ensure that the pins rotate freely. If the pins
do not rotate freely, grease them.
Installing an Auger
Note: Always use the traction unit to lift and move
WARNING
the attachment. To move an auger without the drive
head, sling a strap over each end of the auger and
hoist it to the desired location.
The auger head swings freely in the cradle
arms. Your hands or fingers could get
pinched and severely injured or amputated if
they are caught between the cradle arms and
the swinging drive head.
WARNING
If you do not fully seat the quick-attach
pins through the attachment mount plate,
the attachment could fall off the machine,
crushing you or bystanders.
Keep your hands and fingers away from the
cradle arms.
1.
Ensure that the quick-attach pins are fully
seated in the attachment mount plate.
2.
WARNING
Hydraulic fluid escaping under pressure can
penetrate skin and cause injury. Fluid injected
into the skin must be surgically removed
within a few hours by a doctor familiar with
this form of injury; otherwise, gangrene may
result.
Park the machine on a level surface, lower the
loader arms, and engage the parking brake (if
applicable).
If you are installing an auger on the Model 22806
drive head, shut off the engine and remove the
key. Position the drive head vertically, slide a
bolt (1/2 x 2-1/2 inches) into the holes in the
front cradle arms, and secure it lightly with a
flange nut (1/2 inch) as shown in Figure 4.
• Ensure that all hydraulic-fluid hoses
and lines are in good condition and all
hydraulic connections and fittings are tight
before applying pressure to the hydraulic
system.
• Keep your body and hands away from
pinhole leaks or nozzles that eject
high-pressure hydraulic fluid.
• Use cardboard or paper to find hydraulic
leaks; never use your hands.
g004515
Figure 4
1. Drive head (front view)
3. Front cradle arm
2. Bolt
3.
4.
6
Start the engine and raise the loader arms so
that the drive head clears the ground.
Shut off the engine and remove the key.
5.
Manually rotate the auger drive head up, until
you can slide a bolt (1/2 x 2-1/2 inches) into the
hole in the cradle arm, securing the drive head.
Lightly secure the bolt with a nut (1/2 inch) as
shown in Figure 5.
g004518
Figure 7
1. Drive head
9.
10.
2. Auger shaft
Shut off the engine and remove the key.
Secure the auger to the drive head with a bolt
(7/8 x 4-1/2 inch) and nut (7/8 inch) as shown
in Figure 8.
g004519
Figure 8
g004516
Figure 5
1. Drive head
1. Bolt (7/8 x 4-1/2 inches)
3. Bolt(s) and nut(s)
2. Nut (7/8 inch)
3. Bolt and flange nut
2. Cradle arm
6.
If using an extension with the auger, insert the
end of the extension into the end of the auger
and secure the auger to the extension with a bolt
(7/8 x 4-1/2 inch) and nut (7/8 inch) as shown
in Figure 6.
11.
Remove the bolts and nuts from the cradle arms
installed in steps 2 (if applicable) and 5.
12.
Start the engine.
13.
Raise the auger free of the ground (Figure 9).
g004517
Figure 6
1. Extension
3. Bolt (7/8 x 4-1/2 inch)
2. Auger
4. Nut (7/8 inch)
g004520
Figure 9
7.
Start the engine.
8.
Maneuver the drive shaft into the end of the
auger shaft or extension (if applicable) as shown
in Figure 7.
14.
7
When the auger is vertical, tilt the attachment
plate rearward until the drive head contacts the
attachment plate to stabilize the auger and keep
it from swinging freely (Figure 9).
Removing an Auger
Digging a Hole
Important: Before digging, ensure that the
ground is free of any trash or debris.
1.
Disengage the auxiliary hydraulics.
2.
Raise the loader arms so the auger comes out
of the hole.
1.
Lower the auger to the soil at the site of the
proposed hole.
2.
Move the throttle lever to the FAST position.
3.
If your traction unit has a speed-selector lever,
move it to the SLOW position.
4.
If your traction unit has a flow-divider control,
move it to the 10 o'clock position.
3.
Drive the machine to the storage location for
the auger.
5.
Pull the auxiliary hydraulics lever to the operator
grip or reference bar to begin digging.
4.
While lowering the arms, drive slowly backwards
until the auger is horizontal.
6.
Lower the auger slowly as the soil is loosened.
As you dig deeper, move the traction unit
backward or forward as required to keep the
auger vertical (Figure 10).
5.
Shut off the engine and remove the key.
6.
Remove the bolt and nut securing the drive head
to the auger or extension.
7.
Start the engine and back the traction unit away
from the auger.
8.
If you used an extension, remove the bolt and
nut securing it and pull it off the auger.
Note: If you have a 24-inch extension installed
between the drive head and the auger, it may be
necessary to raise the auger as high as possible
and then move the traction unit backward to pull
the auger the rest of the way out of the hole.
g004521
Figure 10
7.
When the auger becomes full of soil, disengage
the auger drive and lift the auger from the hole.
Engage the auger drive to spin off the soil, then
resume digging.
Important: Switching the auxiliary
hydraulics lever rapidly from forward to
reverse will help to shake off the soil.
DANGER
If you are using Model 22806, excessive
downward force may cause the bit to wobble
uncontrollably, which could tip the traction
unit. You or bystanders could be pinned or
seriously injured.
Do not use excessive downward pressure on
the bit. Allow the bit to pull itself into the soil.
8
Transport Position
• When transporting an auger smaller than 51 cm
(20 inch) diameter over long distances or slopes,
do the following:
• When transporting any size auger over short
distances or an auger larger than 51 cm (20 inch)
diameter over longer distances, do the following:
1.
Raise the auger so that it clears the ground
and is vertical (Figure 9).
1.
While lowering the arms, drive slowly
backwards until the auger is horizontal, then
engage the parking brake (if applicable).
2.
Shut off the engine and remove the key.
3.
Manually rotate the auger drive head up,
until you can slide a bolt (1/2 x 2-1/2 inches)
into the hole in the cradle arm, securing the
drive head. Lightly secure the bolt with a nut
(1/2 inch) as shown in Figure 5.
4.
As you transport the auger, keep it as close
to the ground as possible, no more than 15
cm (6 inches) above the lowest position.
g004520
Figure 11
g244918
2.
Tilt the attachment plate rearward until the
drive head contacts the attachment plate to
stabilize the auger and keep it from swinging
freely.
Figure 12
1. No more than 15 cm (6 inches) above the lowest position
9
Maintenance
Recommended Maintenance Schedule(s)
Maintenance Service
Interval
Maintenance Procedure
After the first 50 hours
• Change the planetary gearcase oil.
Before each use or daily
Every 1,000 hours
Before storage
• Grease the cradle arm pivot points. (Grease all fittings immediately after every
washing.)
• Check the auger teeth and replace them if they are damaged or worn.
• Change the planetary gearcase oil.
• Check the auger teeth and replace them if they are damaged or worn.
• Paint chipped surfaces.
CAUTION
If you leave the key in the switch, someone could accidently start the engine and seriously
injure you or other bystanders.
Remove the key from the switch before you perform any maintenance.
Greasing the Cradle Arm
Pivot Points
Service Interval: Before each use or daily (Grease
all fittings immediately after every
washing.)
Grease Type: General-purpose grease
1.
Park the machine on a level surface, engage
the parking brake (if applicable), and lower the
loader arms.
2.
Shut off the engine and remove the key.
3.
Clean the grease fittings with a rag.
4.
Connect a grease gun to each fitting.
1. Planetary gear case
5.
Pump grease into the fittings until grease begins
to ooze out of the bearings.
2. Bolts
6.
Wipe up any excess grease.
2.
Changing the Planetary
Gear Case Oil
Remove the 4 bolts securing the motor and
remove the motor, allowing all the oil to drain
into the pan.
3.
When the oil is completely drained, turn the
drive head so that the opening is facing the up.
Service Interval: After the first 50 hours
4.
Add oil to the gearcase.
5.
Replace the motor and secure it with the four
bolts removed previously. Torque the bolts to
142 N∙m (105 ft-lb).
g004522
Figure 13
Every 1,000 hours
Type: Mild, extreme pressure lubricant, rated
API-GL-5, number 80 or 90
Capacity: 0.4 L (13.6 fl oz)
1.
Support the drive head over an oil pan (Figure
13).
10
3. Motor
Storage
1.
Before long term storage, wash the attachment
with mild detergent and water to remove dirt and
grime.
2.
Check and tighten all bolts, nuts, and screws.
Repair or replace any damaged or worn part.
3.
Ensure that all hydraulic couplers are connected
together to prevent contamination of the
hydraulic system.
4.
Paint all scratched or bare metal surfaces. Paint
is available from your Authorized Service Dealer.
5.
Store the attachment in a clean, dry garage or
storage area. Cover it to protect it and keep it
clean.
11
Troubleshooting
Problem
The drive head does not operate.
Possible Cause
Corrective Action
1. Hydraulic coupler not completely
connected.
1. Check and tighten all couplers.
2. A hydraulic coupler needs to be
replaced.
3. There is an obstruction in a hydraulic
hose.
4. A hydraulic hose is kinked.
5. The gearbox is contaminated.
2. Check the couplers and replace any
that are worn or damaged.
3. Find and remove the obstruction.
12
4. Replace the kinked hose.
5. Refer to your Authorized Service
Dealer.
Notes:
Notes:
Declaration of Incorporation
The Toro Company, 8111 Lyndale Avenue South, Bloomington, MN, USA declares that the following unit(s)
conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain
Toro models as indicated on the relevant Declarations of Conformity.
Model No.
Serial No.
Product Description
22805
402000000 and Up
Auger Head
22806
402000000 and Up
Universal Swivel Auger Head
Invoice Description
AUGER POWER HEAD
ATTACHMENT CE
SWIVEL AUGER POWER
HEAD ATTACHMENT CE
General Description
Directive
Auger
2006/42/EC
Auger
2006/42/EC
Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.
We will undertake to transmit, in response to requests by national authorities, relevant information on this partly
completed machinery. The method of transmission shall be electronic transmittal.
This machinery shall not be put into service until incorporated into approved Toro models as indicated on the
associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in
conformity with all relevant Directives.
Certified:
Authorized Representative:
Marcel Dutrieux
Manager European Product Integrity
Toro Europe NV
Nijverheidsstraat 5
2260 Oevel
Belgium
Joe Hager
Sr. Engineering Manager
8111 Lyndale Ave. South
Bloomington, MN 55420, USA
February 6, 2018
Tel. +32 16 386 659
European Privacy Notice
The Information Toro Collects
Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you
to share certain personal information with us, either directly or through your local Toro company or dealer.
The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies
in your country.
BY SHARING YOUR PERSONAL INFORMATION WITH US, YOU ARE CONSENTING TO THE PROCESSING OF YOUR PERSONAL INFORMATION
AS DESCRIBED IN THIS PRIVACY NOTICE.
The Way Toro Uses Information
Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell
you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not
sell your personal information to any other company. We reserve the right to disclose personal information in order to comply with applicable laws and
with requests by the appropriate authorities, to operate our systems properly or for our own protection or that of other users.
Retention of your Personal Information
We will keep your personal information as long as we need it for the purposes for which it was originally collected or for other legitimate purposes
(such as regulatory compliance), or as required by applicable law.
Toro's Commitment to Security of Your Personal Information
We take reasonable precautions in order to protect the security of your personal information. We also take steps to maintain the accuracy and current
status of personal information.
Access and Correction of your Personal Information
If you would like to review or correct your personal information, please contact us by email at [email protected]
Australian Consumer Law
Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.
374-0282 Rev C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement