ESP 26404 Sangamo Time Switch Manual

ESP 26404 Sangamo Time Switch Manual
Instruction Manual 26404 (Pg 1 / 2)
Time switch (weekly program)
Directory
Connection diagram
1. Safety instructions
2. Initial operation
3. DCF (Installation DCF-receiver)
4. Menu overview
5. Symbol legend
6. Key function
7. Handling advice
8. Channel ON OFF / Permanent P
9. Programming menu
10. Standard weekly program
11. Example of a standard weekly
switching time
12. Cycle
13. Cycle options
70mm (4 channels)
Weekly time switch
14. Pulse
15. Priority of the switching programs
16. Permanentprogram
17. External Input
18. Channel keys
19. Additional adjustments
20. Program modify
21. Data-key
2. Initial operation
1. Safety instructions
!
The installation and assembly of electrical equipment must be only carried out only
by a skilled Person! Otherwise fire danger or danger of an electric shock exists!
!
Connect the supply voltage/frequency as stated on the product label!
!
Warranty void if housing opened by unauthorised person!
!
The electronic circuit is protected against a wide range of external influences.
Incorrect operating may occur if external influences exceed certain limits!
3. DCF (Installation of the DCF-antenna FU 20)
The time switch is delivered in sleep-mode, the display is switched off. The time switch can process the DCF signal.
The antenna FU 20 is not included in delivery of the time switch.
Press -button for 1 second.
Disconnect power supply voltage
The current date and time is already programmed and European
daylight savings time is activated.
Connect the antenna as indicated by the connection diagram
Select the desired language by pressing
-buttons and confirm it by
Connect supply voltage
pressing . (Remark: By pressing you move one step backwards
Antenna symbol (LCD) flashes for approx. 3 minutes
from the current position)
Reception is not possible if severe interference is present
If required, date, time and daylight savings time mode can be adjusted
(Permanent flashing of the symbol / The oscillating crystal is used as time base)
also by pressing
-buttons and a subsequent confirmation with .
Defective wire between antenna and time switch
(No antenna symbol visible / The oscillating crystal is used as time base)
4. Menu overview
5. Symbol legend
Channel is switched ON
Channel is switched OFF
For the current date the “holiday program” / “permanent by date” is activated
Standard programming step
Current state is based on a manual over-ride. The state will be cancelled with the next
programming step
Current state is based on a manual over-ride. The state is permanent until terminated manually
Days of the week Monday, Tuesday, ... Sunday;
The underscores indicate if the program is active for the days above
Current state is based on a switching time with pulse function
Current state is based on a switching time with cycle function
Is displayed if the corresponding channel is activated by the external input.
Element within sub-menu “program delete”
DCF: The time switch receives the signal for the DCF -77 time standard
6. Key function
1. To access the Enter-mode (program, adjustments, options) from the automatic-mode.
2. To revert to the beginning of the current (sub-) menu.
The time switch is locked; to unlock the device the PIN has to be entered
1. To adjust the flashing digit.
2. To scroll through a choice
1. Automatic-mode: To switch the channel ON or OFF until the next programming step occurs.
2. Automatic-mode: A push longer than 3 sec. = Permanent switching status (7).
1. To activate the time switch when operated without power supply.
2. To confirm the selection or the entered data.
7. Handling advice
The time switch is programmable without external power supply
after pressing the -button.
To revert one step or one level back while in the Enter-Mode press
.
After completion of a (sub-) menu confirming end will return the
device into the automatic-mode.
With
the choice changes from end to continue . By
confirming continue the time switch returns to the beginning of
the current (sub-) menu.
When confirming end before completion, the time switch returns
to the automatic-mode without saving the entered data.
8. Channel ON OFF / Permanent P
9. Programming menu
Channel ON OFF
By pushing
-buttons a manual switch of the channels
take place. The resulting switching status is marked with
the hand-symbol and remains until the next programming
step occurs. (temporary over-ride)
16
Permanent switching status P
By pressing the corresponding channel button
for
more than 3 sec. the channel is permanently switched ON
or OFF. The status remains until the next manual switching
occurs (> 3 sec.). (permanent over-ride)
*within yearly time switches
10. Standard weekly program
11. Example for the programming of STANDARD switching times (ONand OFF)
A. If you want to program a standard weekly switching time ( on ,
) confirm Standard
with
.
with
-buttons and confirm with .
B. For regular switching times choose on or
C. Within this level you activate the days of the week (1…7) on which the switching time should happen.
With
you activate “yes” or deactivate “no” the corresponding date. Confirm each day with .
D. Adjustment of the time: Hours
and . Minutes
and .
E. Verify the entered switching time: If the flashing summary of the programming step is correct, verify on
or
with . After verification you have the choice between edit/delete
and end with
.
with .
F. If you want to proceed with programming, confirm next switching
To leave the programming menu confirm end .
Information: You can easily transfer switching times from one channel to the other if you use the
copy function.
**The cycle function will only be available if it is activated (point 13)
12. Cycle
Standard weekly program:
Program -> new program
-> channel A/B/C/D
13. Cycle options
-> Standard
-> …
Options
-> Cycle
-> Cycle 1 - 4
-> …
You have the possibility to define 4 different Cycles. For these purposes choose menu Options and sub-menu Cycle . The different
cycles can be activated, defined or deactivated (the max. value for pulse or pause is 9:59:59 h:mm:ss):
Choose menu Options and sub-menu Cycle and confirm with .
For the cycle function it is possibile to enter a periodic switching time. The time switch acts as a recycling timer and
switches between pulse (ON) and pause (OFF). The max. value for pulse and pause is 9:59:59 h:mm:ss.
Select with
-buttons one out of the 4 cycles ( Cycle 1 – Cycle 4 ) and confirm with .
If you haven’t defined and activated a cycle, the cycle function will not be available as switching time. Therefore you
Activate the cycle by changing No to Yes with
-buttons and subsequent confirming with .
have to activate and define at least one of the four cycles within menu Options and sub-menu Cycle (point 13).
Define duration of the pulse „on-time“
(
-> …).
The cycle switching time will be terminated by another switching time ( on ,
, pulse ) or by another cycle switching
Define duration of the pause
(
-> …).
time.
Confirm End with .
The cycle is now offered within the programming menu.
Further applications of the cycle function in combination with: External Input function and/or Channel keys function.
14. Pulse
Standard weekly program:
Program -> new program
-> channel A/B/C/D
15. Priorities of the switching programs
-> Standard
-> …
The pulse function provides you the opportunity of programming a switching time with a defined duration.
As soon as the pulse-duration has expired the time switch switches OFF automatically (the duration of the pulse is up to
59:59 mm:ss).
Standard switching times and Permanent by date are executed according to their
corresponding priority (by channel and date)
All switching programs except Extra switching times, suspend all other switching programs with lower priority:
highest priority
manual over-ride Permanent (3 sec. push)
Permanent by date
lowest priority
Standard weekly program
P/N 26404 Manual Issue A
Instruction Manual 26404 (Pg 2 / 2)
Time switch (weekly program)
16. Permanent program
Program -> new program
-> channel A/B/C/D
-> permanent
->
…
The permanent by date program (holiday program) is a permanently on or off status of the channel for the programmed dates. The number of switching times is only limited by the total number of free memory locations. Adjust channel, switching function and the
duration by date. The following options are additionally available for the permanent by date program:
Without special function: The program will be applied each year fixed to the entered dates.
With Easter function:
The time switch takes into account the yearly shift for Easter holiday for following years and corrects the activation dates. (For programs relative to Easter, Pentecost Carnival, Ascension,...).
With 1xfunction:
The Program will be applied only once.
17. External Input (within 70 mm time switches)
Options
-> Input -> …
The external input can be connected to a switched contact such as a push-button or light switch. Therefore you can activate and de-activate functions from a remote location or automatically from a control system:
Connection external inputs:
Connect the voltage/frequency as stated on the product label!
External input 1: A switch or pushbutton can be connected to EXT 1: Terminal 6 (Voltage EXT 1 = Supply voltage of the time switch)
External input 2: A potential free switch or pushbutton can be connected to EXT 2: Terminals 13 u. 14 (potential free = 0V)
Functional options of the „external input“:
Within menu Options and submenu Input you have to define if a switch or a push-button-signal will be applied to the external input. Furthermore you can choose the channel(s) which react to the external signal:
Using the
-buttons select if you are connecting a pushbutton or a switch and confirm by pressing .
Select the channel(s) which will be controlled by the external signal with the
buttons (channel … yes)
and confirm by pressing . Channels which should not be controlled by the external signal remain deactivated, confirm channel … no
press to confirm
then
Define a response function within menu Options and submenu Channel-keys
. This function will be performed by the output channel when the external input is activated!
The pre-defined (default) setting is the standard ‘ Change function’
which changes the switching status from ON to OFF and vice versa.
18. Channel keys
Options
-> channel-keys
-> …
Within the Options menu you will find submenu channel-keys
. Here you have the
opportunity to assign different response functions to the output channels.
These response functions will only be carried out when using the channel-keys
of the time
switch (manual over-ride) or optionally when activating the channel with the external input. Thus,
a programmed switching time will be executed as usual, independent of the settings within this
channel-key-menu.
The correlation between the channel-keys and the channels is as follows:
channel A => channel key A (push-button “A” of the device) / channel B => channel key B …
Overview „channel-keys“ functions:
If you have assigned a specific response function to a channel, this switching function will occur if you push the channel-button on the front plate of the time
switch (or if the external input for this channel is activated and a signal is applied to the input). For each channel one out of the following functions can be
defined:
Change function
(default setting) : By pressing the channel key (or optionally using the external input) the switching status changes from ON to OFF or
OFF to ON. This corresponds to a standard manual over-ride of the channel.
Timer function:
By pressing the channel key (or optionally using the external input) the Timer starts and the corresponding channel switches ON. After
the expiry of the Timer-time the channel switches OFF . If the channel receives another signal before the expiry of time the time switch reacts as follows:
After pressing the channel-button = Timer stops and the channel switches OFF.
Signal on the external input = Timer restarts/ Staircase lighting timer -> Resettable.
Cycle 1 – 4:
By pressing the channel key (or optionally using the external input) the cycle function starts. Attention: This function is only available if
the cycle is activated and defined in advance within menu Options and submenu Cycle .
Perm on: By pressing the channel key (or optionally using the external input) the channel switches permanently ON. This status remains active until the
channel key of the device is pressed again.
Perm off:
By pressing the channel key (or optionally using the external input) the channel switches permanently OFF . This status remains active until the
channel key of the device is pressed again.
The Change function, Timer function and Cycle functions will be overridden by the regular switching program or by a manual over-ride!!!
** The cycle function will only be offered if it is activated (point 13)
19. Additional adjustments
Menu
Main menu
Program query
Program
Program copy
Program
Program delete
Program
Application
Program -> Program modify
-> …
To query the programming steps and remaining memory locations
Copy from one channel to another. Memory of the channel won’t be
overwritten; the copied switching steps appear additionally.
! Permanent by date function is not copied!
Date-Time
Summertime
Language
Adjustment
Adjustment
Adjustment
Deletion of switching time(s). The program for all channels, single
channels and single programming steps within on channel can be
deleted.
Adjustment of date and time
Adjustment of the daylight saving time mode (ON/OFF)
Choice of languages
Factory Defaults
Adjustment
Reset to the state of delivery.
! Date, time and switching program will be lost!
Counter
Options
Displays the hour counter and pulse counter for each channel and
the time switch itself.
PIN-Code
Options
The time switch can be locked with a 4-digit PIN-Code. The code
can be adjusted, activated and deactivated. If you have forgotten
the Code please call customer service.
Reset-Function
20. Program modify
Within Program modify
each single switching time can be modified.
25. Data-key
With a Data-key following activities are possible:
Save data : Writes the data from the time switch into the memory of the Data-key.
Program timeswitch
: Writes the data located inside the Key into the memory.
Key function
: The time switch will solely apply programming steps from the Data-key. The
switching program of the time switch is suppressed.
Key readout
: To query the switching program of the Data-key.
Press all front keys for 2 seconds. The time switch is reset. The values for date and
time will be deleted and have to be re-entered. The switching program has not
been deleted!
P/N 26404 Manual Issue A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement