JOHN LEWIS JLDWW929 User Manual

JOHN LEWIS JLDWW929 User Manual
Dishwasher
JLDWW929
User Manual
Contents
Safety information
Children and vulnerable people safety
General Safety
Safety instructions
Installation
Electrical connection
Water connection
Use
Service
Disposal
Installation
Unpacking
Fitting under the kitchen worktop
Removing the appliance worktop
Levelling of the appliance
Product description
Control panel
Indicators
Programmes
Consumption values
Information for test institutes
Settings
Programme selection mode and user mode
The water softener
The rinse aid empty notification
DryAssist
Options
Options
Extra dry
Time save
Hygiene plus
2
3
3
3
5
5
5
5
5
6
6
7
7
7
7
8
9
10
10
12
13
13
14
14
14
15
15
17
17
17
17
18
Before first use
The salt container
Filling with rinse aid
Daily use
Loading cutlery and dishes
Using the detergent
Setting and starting a programme
Hints and tips
General
Using salt, rinse aid and detergent
What to do if you want to stop using multitablets
Loading the baskets
Before starting a programme
Unloading the baskets
Care and cleaning
Cleaning the filters
Cleaning the spray arms
External cleaning
Internal cleaning
Troubleshooting
The washing and drying results are not
satisfactory
Product information sheet
Additional technical information
Water connection
Water inlet connection
Water drain connection
Electrical connection
Repairs - after sales service
19
19
20
21
21
24
25
26
26
26
26
26
27
27
28
28
29
29
29
30
31
34
35
36
36
36
38
39
Dishwasher User Manual
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or usage.
Always keep the instructions in a safe and accessible location for
future reference.
Children and vulnerable people safety
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from the
appliance unless continuously supervised.
Do not let children play with the appliance.
Keep detergents away from children.
Keep children and pets away from the appliance when the door is
open.
Children shall not carry out cleaning and user maintenance of the
appliance without supervision.
General Safety
•
This appliance is intended to be used in household and similar
applications such as:
– farm houses; staff kitchen areas in shops, offices and other
working environments;
Dishwasher User Manual
3
by clients in hotels, motels, bed & breakfast and other residential
type environments.
Do not change the specification of this appliance.
The operating water pressure (minimum and maximum) must be
between 0.5 (0.05) / 8 (0.8) bar (MPa)
Follow the maximum number of 9 place settings.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly qualified
persons in order to avoid a hazard.
Put the cutlery in the cutlery basket with the sharp ends pointing
down or put them in the cutlery drawer in a horizontal position
with the sharp edges down.
Do not leave the appliance with the open door unattended to avoid
stepping accidentally onto it.
Before any maintenance operation, deactivate the appliance and
disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean the
appliance.
If the appliance has ventilation openings in the base, they must not
be covered e.g. by a carpet.
The appliance is to be connected to the water mains using the new
supplied hose-sets. Old hose sets must not be reused.
–
•
•
•
•
•
•
•
•
•
•
4
Dishwasher User Manual
Safety instructions
Installation
Warning! Only a qualified
person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Follow the installation instructions supplied with
the appliance.
• Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
• Do not install or use the appliance where the
temperature is less than 0 °C.
• Install the appliance in a safe and suitable place
that meets installation requirements.
• This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
Water connection
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water
meters, etc.), let the water flow until it is clean
and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
• The water inlet hose has a safety valve and a
sheath with an inner mains cable.
Electrical connection
Warning! Risk of fire and
electric shock.
• The appliance must be earthed.
• Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after the
installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Dishwasher User Manual
Warning! Dangerous
voltage.
• If the water inlet hose is damaged, immediately
close the water tap and disconnect the mains
plug from the mains socket. Contact the
Authorised Service Centre to replace the water
inlet hose.
Use
• Do not put flammable products or items that
are wet with flammable products in, near or on
the appliance.
5
• Dishwasher detergents are dangerous. Follow
the safety instructions on the detergent
packaging.
• Do not drink and play with the water in the
appliance.
• Do not remove the dishes from the appliance
until the programme is complete. Some
detergent may remain on the dishes.
• Do not sit or stand on the open door of the
appliance.
• The appliance can release hot steam if you open
the door while a programme operates.
Service
• To repair the appliance contact the Authorised
Service Centre.
• Use original spare parts only.
Disposal
Warning! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children and
pets to get closed in the appliance.
6
Dishwasher User Manual
Installation
Warning!
• It is dangerous to alter the
specifications or attempt to
modify the appliance in any way.
• This appliance is heavy. Care
should be taken when moving it.
• Care must be taken to ensure
that the appliance does not stand
on the electrical supply cable.
• Any electrical or plumbing work
required to install this appliance
must be carried out by a qualified
electrician or plumber.
570-600 mm
820 mm
450 mm
Unpacking
• Remove all packaging before positioning the
appliance.
• Position the appliance next to a water tap and a
drain.
Fitting under the kitchen
worktop
By removing the worktop of the appliance, you
can install it under the kitchen worktop or a
close fitting sink. The dimensions of the recess
must correspond to those shown in the picture.
Removing the appliance
worktop
1. Remove the appliance worktop by unscrewing
the two rear retaining screws (1).
1
2. Pull the worktop from the back of the
appliance (2).
Dishwasher User Manual
7
or tighten the adjustable feet until the level of
the appliance is perfect.
2
3. Lift the worktop (3) and slide it out of the front
slots.
3
Insert the appliance once the levelling has been
done. When inserting the appliance, ensure that
the water inlet and drain hoses are not kinked
or squashed. During all operations that involve
accessibility to internal components the
appliance must be unplugged. Be sure that once
the appliance has been installed, it is easily
accessible for the service engineer in the event
that a repair is required. If the appliance is later
used as a freestanding appliance, the original
worktop must be reassembled The plinth on
freestanding appliances is not adjustable.
Caution! It is necessary to
protect the underside of the
kitchen worktop from
condensation. A plastic top
cover can be purchased,
contact your local John Lewis
branch.
Levelling of the appliance
Good levelling is essential for correct closure
and sealing of the appliance door. When the
appliance is correctly levelled, the door will not
catch on either side of the cabinet. If the
appliance door does not close correctly, loosen
8
Dishwasher User Manual
Product description
2
1
3
10
98
1.
2.
3.
4.
5.
6.
Worktop
Upper spray arm
Lower spray arm
Filters
Rating plate
Salt container
Dishwasher User Manual
7 6 54
7.
8.
9.
10.
Air vent
Rinse aid dispenser
Detergent dispenser
Upper basket
9
Control panel
1
2
8
1.
2.
3.
4.
5.
On/off button
Programmes button
Programme indicators
Display
Delay button
3
4
7
5
6
6. Option button
7. Indicators
8. Start button
Indicators
Indicator
Description
Wash
Washing phase. It comes on when the washing phase operates.
Rinse
Rinsing phase. It comes on when the rinsing phase operates.
Dry
Drying phase. It comes on when the drying phase operates.
End of cycle
End indicator.
Time save
Time save indicator.
Extra dry
Extra dry indicator.
10
Dishwasher User Manual
Indicator
Description
Rinse aid
Rinse aid indicator. It is always off while the programme operates.
Salt
Salt indicator. It is always off while the programme operates.
Delay start
Delay indicator.
Hygiene plus
Hygiene plus indicator.
Dishwasher User Manual
11
Programmes
The order of the programmes in the table may
not reflect their sequence on the control panel.
Programme
Degree of soil
Type of load
Programme phases
Options
50° Eco 1)
•
•
Normal soil
Crockery and cutlery
•
•
•
•
Pre-wash
Wash 50 °C
Rinses
Dry
•
•
•
Hygiene plus
Time save
Extra dry
45°-70° Auto 2)
•
•
All
Crockery, cutlery,
pots and pans
•
•
•
•
Hygiene plus
Extra dry
•
•
Pre-wash
Wash from 45 °C to
70 °C
Rinses
Dry
70° Intensive
•
•
Heavy soil
Crockery, cutlery,
pots and pans
•
•
•
•
Pre-wash
Wash 70 °C
Rinses
Dry
•
•
•
Hygiene plus
Time save
Extra dry
45° Glass
•
•
Normal or light soil
Delicate crockery and
glassware
•
•
•
Wash 45 °C
Rinses
Dry
•
Extra dry
60° Quick 3)
•
•
Fresh soil
Crockery and cutlery
•
•
Wash 60 °C
Rinses
•
•
Hygiene plus
Extra dry
50° Quiet 4)
•
•
Normal soil
Crockery and cutlery
•
•
•
•
Pre-wash
Wash 50 °C
Rinses
Dry
•
Extra dry
1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal
soil. (This is the standard programme for test institutes).
2) The appliance senses the degree of soil and the quantity of items in the baskets . It automatically adjusts the temperature and
the quantity of water, the energy consumption and the programme duration.
3) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
4) This is the most silent programme. The pump works at a very low speed to decrease the level of noise. Because of the low
speed, the programme duration is long.
12
Dishwasher User Manual
Consumption values
Water
(l)
Energy
(kWh)
Duration
(min)
9.9
0.688
240
45°-70° Auto
6 - 12
0.5 - 1.2
40 - 150
70° Intensive
11 - 13
1.0 - 1.2
130 - 150
60° Quick
8
0.6 - 0.8
30
50° Quiet
9 - 11
0.9 - 1.1
220 - 230
45° Glass
10 - 12
0.8 - 0.9
60 - 80
Programme 1)
50° Eco
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can
change the values.
Information for test institutes
To receive the necessary information for
conducting performance tests (e.g. according to
EN60436), send an email to:
info.test@dishwasher-production.com
In your request please include the product
number code (PNC) found on the rating plate.
For any other questions regarding your
dishwasher please refer to the service book
provided with your appliance.
Dishwasher User Manual
13
Settings
To enter the user mode, press and hold
simultaneously Delay and Option until the
indicators Eco, Auto and Intensive start flashing and
the display is blank.
Programme selection mode
and user mode
When the appliance is in programme selection
mode it is possible to set a programme and to
enter the user mode.
The water softener
The water softener removes minerals from the
water supply, which would have a negative effect
on the washing results and on the appliance.
Settings available in the user mode:
• The level of water softener according to the
water hardness.
• Activation or deactivation of the rinse aid
empty notification.
• Activation or deactivation of DryAssist.
The higher the content of these minerals, the
harder your water is. Water hardness is
measured in equivalent scales.
As the appliance stores the saved
settings, there is no need to configure it
before every cycle.
How to set the programme selection
mode
The appliance is in programme selection mode
when the programme indicator 50° Eco is on
and the display shows the programme duration.
The water softener should be adjusted
according to the hardness of the water in your
area. Your local water authority can advise you
on the hardness of the water in your area. It is
important to set the right level of the water
softener to assure good washing results.
After activation, the appliance is in programme
selection mode by default. If not, set the
programme selection mode the following way:
Press and hold simultaneously Delay and Option
until the appliance is in programme selection mode.
Softening hard water increases the
consumption of water and energy
as well as the programme duration.
The higher the level of water
softener, the higher the
consumption and the longer the
duration.
How to enter user mode
Make sure the appliance is in programme
selection mode.
Water hardness
German degrees
(°dH)
French degrees
(°fH)
mmol / l
Clarke degrees
Water softener level
47 - 50
84 - 90
8.4 - 9.0
58 - 63
10
43 - 46
76 - 83
7.6 - 8.3
53 - 57
9
14
Dishwasher User Manual
German degrees
(°dH)
French degrees
(°fH)
mmol / l
Clarke degrees
Water softener level
37 - 42
65 - 75
6.5 - 7.5
46 - 52
8
29 - 36
51 - 64
5.1 - 6.4
36 - 45
7
23 - 28
40 - 50
4.0 - 5.0
28 - 35
6
19 - 22
33 - 39
3.3 - 3.9
23 - 27
5 1)
15 - 18
26 - 32
2.6 - 3.2
18 - 22
4
11 - 14
19 - 25
1.9 - 2.5
13 - 17
3
4 - 10
7 - 18
0.7 - 1.8
5 - 12
2
<4
<7
<0.7
<5
1 2)
1) Factory setting.
2) Do not use salt at this level.
Regardless of the type of detergent used,
set the proper water hardness level to
keep the salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard
water.
How to set the water softener level
Make sure the appliance is in user mode.
1. Press Programmes.
• The indicators Auto and Intensive are off.
• The indicator Eco still flashes.
• The display shows the current setting: e.g.
= level 5.
2. Press Programmes repeatedly to change the
setting. Each pressing of Programmes
increases the level number. After reaching level
10, the count starts again from level 1.
3. Press the on/off button to confirm the setting.
When rinse aid chamber is empty, the rinse aid
indicator is turned on notifying to refill rinse aid.
If the drying results are satisfactory while using
multi-tablets only, it is possible to deactivate the
notification for refilling rinse aid. However, for
best drying performance, always use rinse aid.
If standard detergent or multi-tablets without
rinse aid are used, activate the notification to
keep the rinse aid refill indicator active.
How to deactivate the rinse aid empty
notification
Make sure the appliance is in user mode.
1. Press Start.
• The indicators Eco and Intensive are off.
• The indicator Auto still flashes.
• The display shows the current setting.
–
= rinse aid empty notification
activated.
The rinse aid empty
notification
= rinse aid empty notification
deactivated.
2. Press Start to change the setting.
3. Press on/off to confirm the setting.
The rinse aid helps to dry the dishes without
streaks and stains.
DryAssist
The rinse aid is automatically released during the
hot rinse phase.
DryAssist improves the drying results with less
energy consumption.
Dishwasher User Manual
–
15
During the drying phase, the door
opens automatically and remains
ajar.
Caution! Do not try to close
the appliance door within 2
minutes after automatic
opening. This can cause
damage to the appliance.
DryAssist is automatically activated with all
programmes excluding Rinse hold (if applicable).
To improve the drying performance refer to the
Extra dry option or activate DryAssist.
Caution! If children have
access to the appliance, it is
advised to deactivate
DryAssist as opening the door
may pose a danger.
How to deactivate DryAssist
Make sure the appliance is in user mode.
1. Press Delay.
• The indicators Eco and Auto are off.
• The indicator Intensive still flashes.
• The display shows the current setting:
= DryAssist activated.
2. Press Delay to change the setting:
=
DryAssist deactivated.
3. Press on/off to confirm and save the setting.
16
Dishwasher User Manual
Options
Options
Desired options must be activated
every time before you start a
programme.
It is not possible to activate or
deactivate options while a
programme is running.
The Option button toggles
between the available options and
their possible combinations.
Not all options are compatible with
each other. If you select non
compatible options, the appliance
automatically deactivates one or
more of them. Only the indicators
of the still active options are on.
If an option is not applicable to a
programme, the related indicator is
off or it flashes quickly for a few
seconds and then goes out.
Activating options can affect the
water and energy consumption as
well as the programme duration.
Extra dry
Activate this option to boost the drying
performance. With the use of this option, the
duration of some programmes, water
consumption and the last rinse temperature can
be affected.
In other programmes the setting of Extra dry is
permanent and it is automatically used in next
cycles. This configuration can be changed at any
time.
Activating Extra dry option deactivates Time
save and vice versa.
How to activate Extra dry
Press Option until the indicator Extra dry turns
on.
If the option is not applicable to the programme,
the related indicator does not turn on or it flashes
quickly for a few seconds and then turns off.
The display shows the updated programme
duration.
Time save
This option increases the pressure and the
temperature of the water. The washing and the
drying phases are shorter.
The total programme duration decreases by
approximately 50%.
The washing results are the same as with the
normal programme duration. The drying results
can decrease.
How to activate Time save
Press Option until the indicator Time save turns
on.
If the option is not applicable to the programme,
the related indicator does not turn on or it flashes
quickly for a few seconds and then turns off.
The display shows the updated programme
duration.
The Extra dry option is a permanent option for
all programmes other than 50° Eco and need
not to be selected at every cycle.
Dishwasher User Manual
17
Hygiene plus
This option provides better hygiene results by
keeping the temperature at 70 °C for at least 10
minutes during the last rinsing phase.
How to activate Hygiene plus
Press Option until the indicator Hygiene plus turns
on.
If the option is not applicable to the programme,
the related indicator does not turn on or it flashes
quickly for a few seconds and then turns off.
The display shows the updated programme
duration.
18
Dishwasher User Manual
Before first use
1. Make sure that the current level of the
water softener agrees with the hardness
of the water supply. If not, adjust the
level of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any processing
residuals that can still be inside the appliance.
Do not use detergent and do not put dishes in
the baskets.
After starting the programme, the appliance
recharges the resin in the water softener for up
to 5 minutes. The washing phase starts only
after this procedure is complete. The procedure
is repeated periodically.
4. Carefully shake the funnel by its handle to get
the last granules inside.
5. Remove the salt around the opening of the salt
container.
The salt container
Caution! Use rough salt
designed for dishwashers only.
Fine salt increases the risk of
corrosion.
The salt is used to recharge the resin in the
water softener and to assure good washing
results in daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container (only
for the first time).
3. Fill the salt container with 1 kg of salt (until it is
full).
Dishwasher User Manual
6. Turn the cap of the salt container clockwise to
close the salt container.
Caution! Water and salt can
come out of the salt container
when you fill it. After you fill
the salt container,
immediately start a
programme to prevent
corrosion.
19
Filling with rinse aid
B
A
M AX
4
1
3 2
+
-
C
D
Caution! Use branded rinse
aid for dishwashers only.
Never fill the rinse aid
dispenser with any other
substances (e.g. dishwasher
cleaning agent, liquid
detergent). This would
damage the appliance.
Rinse aid ensures thorough rinsing,
and spot and streak free drying.
Rinse aid is automatically added
during the last rinse.
1. Press the release button (D) to open the lid
(C) of the rinse aid dispenser.
2. Fill the rinse aid dispenser (A) with rinse aid.
The maximum level for filling is indicated by
'MAX'.
3. Clean up any rinse aid spilt during filling with an
absorbent cloth to avoid excess foaming during
the next washing programme.
4. Close the rinse aid dispenser. Press the lid until
it locks into position.
20
Dishwasher User Manual
Daily use
1. Open the water tap.
2. Press the on/off button to activate the
appliance.
Make sure that the appliance is in programme
selection mode.
• If the salt indicator is on, fill the salt
container.
• If the rinse aid indicator is on, fill the rinse
aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for the
type of load and the degree of soil.
Loading cutlery and dishes
Warning! Always close the
appliance door after loading
the baskets. An open door can
be a hazard.
Caution! Always ensure that
the spray arms can rotate
freely before you close the
appliance door and start the
programme.
The lower basket
The lower basket is designed to take pots, pans,
lids, dishes, salad bowls and cutlery. Serving
dishes and large lids should be arranged around
the edge of the basket, ensuring that the spray
arms can turn freely.
Dishwasher User Manual
21
The two rows of prongs in the lower basket can
lie flat to allow you to load pots, pans and
Mix spoons with other cutlery to prevent them
from sticking together. For best results we
recommend you use the cutlery grid. If the size
and dimensions of the cutlery do not allow the
use of the grid, this can be easily removed.
bowls.
The cutlery basket
Warning! Knives with long
blades, stored in an upright
position, are a potential
hazard. Long and/or sharp
items of cutlery such as
carving knives must be
positioned horizontally in the
upper basket. Take care when
loading or unloading sharp
items such as knives. Forks
and spoons should be placed
in the removable cutlery
basket with the handles facing
downwards and the knives
with their handles facing
upwards
22
The upper basket
Arrange items on and underneath the cup racks
so that water can reach all surfaces.
Dishwasher User Manual
Caution! Ensure that the
spray arms can rotate freely
before you close the appliance
door.
Adjusting the height of the upper basket
Caution! Never lift or lower
the basket on one side only.
To load very large plates move the upper basket
to the higher position.
Glasses with long stems can be placed upside
down in the cup racks. For taller items, the cup
racks can be folded upwards.
Dishwasher User Manual
23
24 cm
27 cm
Moving back the upper basket to the lower
position
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and then allow
the mechanism to drop back down slowly,
keeping hold of it.
Using the detergent
A
B
20 cm
30
20
31 cm
C
Caution! Only use detergent
specifically designed for
dishwashers.
Moving the upper basket to the higher
position
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the
mechanism is engaged and the basket is stable.
24
1. Press the release button (B) to open the lid
(C).
2. Put the detergent, in powder or tablets, in the
compartment (A).
3. If the programme has a prewash phase, put a
small quantity of detergent on the inner part of
the appliance door.
4. Close the lid. Make sure that the release
button locks into position.
Dishwasher User Manual
Setting and starting a
programme
The Auto Off function
This function decreases energy consumption by
deactivating automatically the appliance when it
is not operating.
The function comes into operation:
• 5 minutes after the completion of the
programme.
• After 5 minutes if the programme has not
started.
Starting a programme
1. Press the on/off button to activate the
appliance. Make sure that the appliance is in
programme selection mode and the door is
closed.
2. Press Programmes again and again until the
indicator of the desired programme is on.
The display shows the programme duration.
3. Set the applicable options.
4. Press Start to start the programme.
• The indicator of the running phase is on.
• The programme duration starts to
decrease with steps of 1 minute.
Starting a programme with delay start
1. Set a programme.
2. Press Delay repeatedly until the display shows
the desired delay time (from 1 to 24 hours).
3. Press Start to begin the countdown.
• The indicator Delay start is on.
• The remaining time counts down in hours.
The final hour is displayed in minutes.
When the countdown is completed, the
programme starts and the indicator of the
running phase is on. The indicator Delay start is
off.
Opening the door while the appliance
operates
Opening the door while a programme is running
stops the appliance. It may affect the energy
consumption and the programme duration.
After closing the door, the appliance continues
from the point of interruption.
Dishwasher User Manual
If the door is opened for more than
30 seconds during the drying
phase, the running programme
ends. It does not happen if the
door is opened by DryAssist
function.
Do not try to close the appliance
door within 2 minutes after
DryAssist automatically opens it, as
this may cause damage to the
appliance.
If, afterwards, the door is closed
for another 3 minutes, the running
programme ends.
Cancelling the delay start while the
countdown operates
When you cancel the delay start you have to set
the programme and options again.
Press and hold simultaneously Delay and Option
until the appliance is in programme selection mode.
Cancelling the programme
Press and hold simultaneously Delay and Option
until the appliance is in programme selection mode.
Make sure that there is detergent in the
detergent dispenser before starting a new
programme.
End of the programme
When the programme is completed the display
shows 0:00 and the end indicator is on.
All buttons are inactive except for the on/off
button.
1. Press the on/off button or wait for the Auto
Off function to automatically deactivate the
appliance.
If you open the door before the activation of
Auto Off, the appliance is automatically
deactivated.
2. Close the water tap.
25
Hints and tips
General
Follow the hints below to ensure optimal
cleaning and drying results in daily use and to
help you protect the environment.
• Remove larger residues of food from the dishes
into the waste bin.
• Do not pre-rinse dishes by hand. When
needed, select a programme with a prewash
phase.
• Always use the whole space of the baskets.
• Make sure that items in the baskets do not
touch or cover each other. Only then can the
water completely reach and wash the dishes.
• You can use dishwasher detergent, rinse aid
and salt separately or you can use the multitablets (e.g. ''All in 1''). Follow the instructions
on the packaging.
• Select a programme according to the type of
load and the degree of soil. 50° Eco offers the
most efficient use of water and energy
consumption.
Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent for
dishwasher. Other products can cause damage
to the appliance.
• In areas with hard and very hard water we
recommend to use plain dishwasher detergent
(powder, gel, tablets containing no additional
agents), rinse aid and salt separately for optimal
cleaning and drying results.
• At least once a month run the appliance with
the use of appliance cleaner which is particularly
suitable for this purpose.
• Detergent tablets do not fully dissolve with
short programmes. To prevent detergent
residues on the tableware, we recommend that
you use the tablets with long programmes.
26
• Do not use more than the correct quantity of
detergent. Refer to the instructions on the
detergent packaging.
What to do if you want to stop
using multi-tablets
Before you start to use separately detergent,
salt and rinse aid do the following procedure.
1. Set the highest level of the water softener.
2. Make sure that the salt and rinse aid containers
are full.
3. Start the shortest programme with a rinsing
phase. Do not add detergent and do not load
the baskets.
4. When the programme is completed, adjust the
water softener according to the water
hardness in your area.
5. Adjust the released quantity of rinse aid.
6. Activate the rinse aid empty notification.
Loading the baskets
• Only use the appliance to wash items that are
dishwasher-safe.
• Do not put in the appliance items made of
wood, horn, aluminium, pewter and copper.
• Do not put in the appliance items that can
absorb water (sponges, household cloths).
• Remove remaining food from the items.
• Make soft the remaining burned food on the
items.
• Put hollow items (cups, glasses and pans) with
the opening down.
• Make sure that cutlery and dishes do not bond
together. Mix spoons with other cutlery.
• Make sure that glasses do not touch other
glasses.
• Put small items in the cutlery basket.
• Put light items in the upper basket. Make sure
that the items do not move.
Dishwasher User Manual
• Make sure that the spray arm can move freely
before you start a programme.
Before starting a programme
Before you start the selected programme, make
sure that:
•
•
•
•
The filters are clean and correctly installed.
The cap of the salt container is tight.
The spray arms are not clogged.
There is enough salt and rinse aid (unless you
use multi-tablets).
• The arrangement of the items in the baskets is
correct.
• The programme is suitable to the type of load
and the degree of soil.
• The correct quantity of detergent is used.
Unloading the baskets
1. Let the tableware cool down before you
remove it from the appliance. Hot items can
be easily damaged.
2. First remove items from the lower basket,
then from the upper basket.
After the programme is completed,
water can still remain on the inside
surfaces of the appliance.
Dishwasher User Manual
27
Care and cleaning
Warning! Before
maintenance, deactivate the
appliance and disconnect the
mains plug from the main
socket.
Dirty filters and clogged spray arms
decrease the washing results. Make
a check regularly and, if necessary,
clean them.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
Cleaning the filters
The filter system is made of 3 parts.
C
4. Wash the filters.
B
A
1. Turn the filter (B) counterclockwise and
remove it.
5. Make sure that there are no residues of food
or soil in or around the edge of the sump.
6. Put back in place the flat filter (A). Make sure
that it is correctly positioned under the 2
guides.
28
Dishwasher User Manual
Internal cleaning
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter (A). Turn
it clockwise until it locks.
• Carefully clean the appliance, including the
rubber gasket of the door, with a soft damp
cloth.
• If you regularly use short duration programmes,
these can leave deposits of grease and limescale
inside the appliance. To prevent this, we
recommend to run long duration programmes
at least 2 times per month.
• To maintain the performance of your appliance
at its best, we recommend to use monthly a
specific cleaning product for dishwashers.
Follow carefully the instructions on the
packaging of the product.
Caution! An incorrect
position of the filters can
cause bad washing results and
damage to the appliance.
Cleaning the spray arms
Do not remove the spray arms. If the holes in
the spray arms are clogged, remove remaining
parts of soil with a thin pointed object.
External cleaning
• Clean the appliance with a moist soft cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive cleaning
pads or solvents.
Dishwasher User Manual
29
Troubleshooting
If the appliance does not start or it stops during
operation. Before you contact an Authorised
Service Centre, check if you can solve the
problem by yourself with the help of the
information in the table.
With some problems, the display shows
an alarm code.
The majority of problems that can occur
can be solved without the need to
contact an Authorised Service Centre.
Warning! Repairs not
properly done may result in
serious risk to the safety of
the user. Any repairs must be
performed by qualified
personnel.
Problem and alarm code
Possible cause and solution
You cannot activate the appliance.
•
•
Make sure that the mains plug is connected to the mains socket.
Make sure that there is no damaged fuse in the fuse box.
The programme does not start.
•
•
•
Make sure that the appliance door is closed.
Press Start.
If the delay start is set, cancel the setting or wait for the end of the
countdown.
The appliance has started the procedure to recharge the resin inside
the water softener. The duration of the procedure is approximately 5
minutes.
•
The appliance does not fill with wa- •
ter.
•
The display shows
or
.
The appliance does not drain the
water.
The display shows
.
The anti-flood device is on.
The display shows
30
•
•
•
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is not clogged.
Make sure that the inlet hose has no kinks or bends.
•
•
•
•
Make sure that the sink spigot is not clogged.
Make sure that the filter in the outlet hose is not clogged.
Make sure that the interior filter system is not clogged.
Make sure that the drain hose has no kinks or bends.
•
Close the water tap and contact an Authorised Service Centre.
.
Dishwasher User Manual
Problem and alarm code
Possible cause and solution
The appliance stops and starts
more times during operation.
•
It is normal. It provides optimal cleaning results and energy savings.
The programme lasts too long.
•
•
Select the Time save option to shorten the programme time.
If the delayed start option is set, cancel the delay setting or wait for
the end of the countdown.
The remaining time in the display
increases and skips nearly to the
end of programme time.
•
This is not a defect. The appliance is working correctly.
Small leak from the appliance door.
•
The appliance is not levelled. Loosen or tighten the adjustable feet (if
applicable).
The appliance door is not centred on the tub. Adjust the rear foot (if
applicable).
•
The appliance door is difficult to
close.
•
The appliance is not levelled. Loosen or tighten the adjustable feet (if
applicable).
Parts of the tableware are protruding from the baskets.
•
Rattling/knocking sounds from inside the appliance.
•
The tableware is not properly arranged in the baskets. Refer to
"Loading cutlery and dishes".
Make sure that the spray arms can rotate freely.
•
The appliance trips the circuit-beak- •
er.
The amperage is insufficient to supply simultaneously all the appliances
in use. Check the socket amperage and the capacity of the meter or
turn off one of the appliances in use.
Internal electrical fault of the appliance. Contact an Authorised Service
Centre.
•
Refer to "Before first use",
"Daily use", or "Hints and
tips" for other possible causes.
Once you have checked the appliance,
deactivate and activate the appliance. If the
problem occurs again, contact an Authorised
Service Centre.
For alarm codes not described in the table,
contact an Authorised Service Centre.
The washing and drying results are not satisfactory
The washing and drying results are not satisfactory
Poor washing results.
•
•
•
Dishwasher User Manual
Refer to "Daily use", "Hints and tips" and "Loading cutlery
and dishes".
Use more intensive washing programmes.
Clean spray arm jets and filter. Refer to "Care and Cleaning".
31
The washing and drying results are not satisfactory
Poor drying results.
•
•
•
•
•
•
There are streaks, whitish stains, or
bluish layers on glasses and dishes.
•
•
Dry water drops on glasses and
dishes.
•
•
The dishes are wet.
•
•
•
•
•
Tableware has been left for too long inside the closed appliance.
There is no rinse aid or the dosage of rinse aid is not enough. Set
the rinse aid dispenser to a higher level.
Plastic items may need to be towel dried.
For the best drying performance activate the option Extra dry.
We recommend to always use rinse aid, even in combination with
multi-tablets.
For the best drying performance activate DryAssist.
The release quantity of rinse aid is too large. Adjust the rinse aid selector to a lower position.
The quantity of detergent is too large.
The released quantity of rinse aid is not sufficient. Adjust the rinse
aid selector to a higher position.
The quality of the rinse aid can be the cause.
For the best drying performance activate the option Extra dry.
The programme does not have a drying phase or has a drying phase
with low temperature.
The rinse aid dispenser is empty.
The quality of the rinse aid can be the cause.
For the best drying performance activate DryAssist.
The interior of the appliance is wet.
•
This is not a defect of the appliance. it is caused by the humidity in
the air that condenses on the walls.
Unusual foam during washing.
•
•
Use the detergent for dishwashers only.
There is a leak in the rinse aid dispenser. Contact an Authorised
Service Centre.
Traces of rust on cutlery.
•
There is too much salt in the water used for washing. Refer to
"The water softener".
Silver and stainless steel cutlery were placed together. Avoid to put
silver and stainless steel items close together.
•
There are residues of detergent in the •
dispenser at the end of the programme.
•
•
The detergent tablet got stuck in the dispenser and therefore was
not completely washed away by water.
Water cannot wash away the detergent from the dispenser. Make
sure that the spray arm is not blocked or clogged.
Make sure that items in the baskets do not impede the opening of
the lid of the detergent dispenser.
Odours inside the appliance.
•
Refer to "Internal cleaning".
Limescale deposits on the tableware,
on the tub and on the inside of the
door.
•
Refer to "The water softener".
32
Dishwasher User Manual
The washing and drying results are not satisfactory
Dull, discoloured or chipped tableware.
•
•
•
Dishwasher User Manual
Make sure that only dishwasher-safe items are washed in the appliance.
Load and unload the basket carefully. Refer to "Loading cutlery
and dishes".
Place delicate items in the upper basket.
33
Product information sheet
Trade Mark
John Lewis
Model
JLDWW929 911054038
Rated capacity (standard place settings)
9
Energy efficiency class
A++
Energy consumption in kWh per year, based on 280 standard clean- 197
ing cycles using cold water fill and the consumption of the low power
modes. The actual energy consumption will depend on how the appliance is used.
Energy consumption of standard cleaning cycle (kWh)
0.688
Power consumption in off mode (W)
0.50
Power consumption in left-on mode (W)
5.0
Water consumption in litres per year, based on 280 standard clean- 2775
ing cycles. The actual water consumption will depend on how the appliance is used
Drying efficiency class on a scale from G (least efficient) to A (most
efficient)
A
The ‘standard programme’ is the standard cleaning cycle to which
the information in the label and the fiche relates. This programme is
suitable to clean normally soiled tableware and is the most efficient
programme in terms of combined energy and water consumption. It
is indicated as "Eco" programme.
50° Eco
Programme time of standard cleaning cycle (min)
240
Duration of the left-on mode (min)
5
Sound power level (db(A) re 1pW)
44
Built in appliance Y/N
No
34
Dishwasher User Manual
Additional technical information
Dimensions
Width / height / depth (mm)
446/850/625
Electrical connection 1)
Voltage (V)
220 - 240
Frequency (Hz)
50
Water supply pressure
Min. / max.
bar (MPa)
0.5 (0.05) / 8 (0.8)
Water supply
Cold water or hot water 2)
max 60 °C
1) Refer to the rating plate for other values.
2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to decrease energy consumption.
Dishwasher User Manual
35
Water connection
Water inlet connection
• This appliance may be fed with either hot
(maximum 60 °C) or cold water. Nevertheless
we advise you use a cold water supply. A hot
water supply is not always efficient with heavily
soiled crockery as it shortens the washing
programmes a lot.
• For making the connection itself, the coupling
nut fitted to the appliance inlet hose is designed
to screw onto a 3/4" gas thread spout or to a
purpose made quick-coupling tap such as the
Press-block.
• The water pressure must be within the limits
given in the ‘Technical information’. Your local
Water Authority will advise you on the average
mains pressure in your area.
• The appliance features inlet and drain hoses
which can be turned either to the left or the
right to suit the installation by means of the
locknut. The locknut must be correctly fitted to
avoid water leaks.
• This appliance has been fitted with safety
features which will prevent the water used in
the appliance from returning back into the
drinking water system. This appliance complies
with the applicable plumbing regulations.
Water drain connection
The end of the drain hose can be connected in
the following ways:
• To the sink outlet spigot, securing it to the
underside of the work surface. This will prevent
waste water from the sink running into the
appliance.
• To a stand pipe provided with venthole,
minimum internal diameter 4 cm.
36
max. 850 mm
max.
4000 mm
min. 400 mm
The drain hose can face either to the right or left
of the appliance.
Ensure the drain hose is not bent or squashed as
this could prevent or slow down the discharge
of water.
The sink plug must not be in place when the
appliance is draining as this could cause the
water to syphon back into the appliance.
If you use a drain hose extension, the internal
diameter must be no smaller than the diameter
of the hose provided.
Likewise the internal diameter of the couplings
used for connections to the waste outlet must
be no smaller than the diameter of the hose
provided.
Our appliances are supplied with a security
device to protect against the return of dirty
water back into the appliance. If the spigot of
your sink has a "no return valve" incorporated
this can prevent the correct draining of your
appliance. We therefore advise you to remove
it.
Dishwasher User Manual
When connecting the drain hose to an under
sink trap spigot, the entire plastic membrane (A)
must be removed. Failure to remove all the
membrane will result in food particles building
up over time eventually blocking the appliance
drain hose spigot.
A
Dishwasher User Manual
37
Electrical connection
Warning! The manufacturer
accepts no liability for failure
to observe the following
safety precautions.
• Safety standards require the appliance to be
earthed.
• Prior to using the appliance for the first time,
ensure that the rated voltage and type of supply
on the rating plate match that of the supply
where the appliance is to be installed. The fuse
rating is also to be found on the rating plate.
• Always plug the mains plug into a correctly
installed shockproof socket.
• Multi-way plugs, connectors and extension
cables must not be used. This could constitute a
fire hazard through overheating.
38
• If necessary, have the domestic wiring system
socket replaced. In case that the electrical cable
has to be replaced, contact your local repair
agent.
• The plug must be accessible after the appliance
has been installed.
• Never unplug the appliance by pulling on the
cable. Always pull the plug.
• The appliance is supplied with a 13 amp plug
attached. Use a 13 amp ASTA approved (BS
1362) fuse if it is necessary to change the fuse in
the plug supplied.
• This appliance complies with the E.C.C.
Directives.
Dishwasher User Manual
Repairs - after sales service
Your John Lewis appliance comes with a three
year guarantee. Your original receipt acts as
your guarantee. Please make sure you retain it.
The guarantee does not cover you against faults
caused by accidental damage or misuse. For
further details visit johnlewis.com/customerservices. If it is not working correctly refer to
the "Troubleshooting" chapter in this user
manual. If a fault occurs which you can not
resolve through following the advice and
information contained within this instruction
manual, the next step is to contact John Lewis
technical support on:
0330 1230106
They will give you details for your local service
engineer. Before calling out an engineer, please
ensure you have read the details under the
heading “Troubleshooting”.
When you contact your local service engineer
you will need to give the following details:
1.
2.
3.
4.
5.
Your name, address and post code
Your telephone number
Clear and concise details of fault
The purchase date as found on your receipt
The model and serial number of the appliance.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
• Mod.......................................
• P.N.C.....................................
• S.N.........................................
IMPORTANT: If you call out an engineer
to a fault listed under the heading
''Troubleshooting'', or to repair a fault
caused by incorrect use or installation, a
charge will be made even if the appliance
is under guarantee.
Spare parts
Dishwasher User Manual
Always insist on genuine spare parts.
An authorised service engineer should service
this product, and only genuine spare parts
should be used. Under no circumstances should
you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons
may cause injury or serious malfunctioning.
Please contact John Lewis technical support on
0330 1230106 for assistance.
Shopping is easy with John Lewis Shops
John Lewis, Aberdeen 01224 625 000
John Lewis, Basingstoke 01256 406200
John Lewis, Bluewater 01322 624 123
John Lewis, Brent Cross 020 8202 6535
John Lewis, Birmingham 0345 604 9049
John Lewis, Cambridge 01223 361 292
John Lewis, Cardiff 02920 536 000
John Lewis, Cheadle 0161 491 4914
John Lewis, Chelmsford 0124 545 8400
John Lewis, Cribbs Causeway 0117 959 1100
John Lewis, Edinburgh 0131 556 9121
John Lewis, Exeter 01392 284150
John Lewis, Glasgow 0141 353 6677
John Lewis, High Wycombe 01494 462 666
John Lewis, Kingston 020 8547 3000
John Lewis, Leicester 0116 242 5777
John Lewis, Leeds 0113 3946299
John Lewis, Liverpool 0151 709 7070
John Lewis, Milton Keynes 01908 679 171
John Lewis, Newcastle upon Tyne 0191 232 5000
John Lewis, Norwich 01603 660 021
John Lewis, Nottingham 0115 941 8282
John Lewis, Oxford Street 020 7629 7711
John Lewis, Peterborough 01733 344 644
John Lewis, Reading 0118 957 5955
John Lewis, Sheffield 0114 276 8511
Peter Jones, Sloane Square 020 7730 3434
John Lewis, Solihull 0121 704 1121
39
John Lewis, Southampton 02380 216 400
Knight & Lee, Southsea 02392 827 511
John Lewis, Stratford 020 8532 3500
John Lewis, The Trafford Centre 0161 491 4040
John Lewis, Watford 01923 244 266
John Lewis, Welwyn 01707 323 456
John Lewis at home
John Lewis, Ashford 01233 811 010
John Lewis, Chester 01244 393 880
40
John Lewis, Chichester 01243 813 030
John Lewis, Croydon 020 8662 4730
John Lewis, Horsham 01403 214 740
John Lewis, Ipswich 01473 275 850
John Lewis, Newbury 01635 263 980
John Lewis, Poole 01202 756 020
John Lewis, Swindon 01793 733 180
John Lewis, Tamworth 01827 300 580
John Lewis, Tunbridge Wells 01892 506 830
John Lewis, York 01904 557 950
Dishwasher User Manual
Environmental concerns
marked with the symbol with the household
waste. Return the product to your local
recycling facility or contact your municipal office.
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it.
Help protect the environment and human health
by recycling waste of electrical and electronic
appliances. Do not dispose of appliances
Dishwasher User Manual
41
*
42
Dishwasher User Manual
Dishwasher User Manual
43
156935211-A-312019 ( Subject to change without notice. )
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement