ZANUSSI ZWI71401WA User Manual
User Manual
GETTING
STARTED?
EASY.
ZWI 71201 WA
ZWI 71401 WA
EN User Manual
Washing Machine
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
•
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
If the appliance has a child safety device, it should be activated.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
2
Do not change the specification of this appliance.
This appliance is intended to be used in household and similar
applications such as:
– staff kitchen areas in shops, offices and other working
environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments;
•
•
•
•
•
•
•
•
•
– areas for communal use in blocks of flats or in launderettes.
Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
•
•
•
•
•
•
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Do not install or use a damaged appliance.
Follow the installation instructions supplied with
the appliance.
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
•
•
•
•
•
•
•
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
Make sure that there is air circulation between
the appliance and the floor.
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
Do not install the appliance directly above a
floor drain.
Do not spray water on the appliance and do not
expose it to excessive humidity.
Do not install the appliance where the appliance
door cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the appliance.
Contact the Authorised Service Centre to
ensure which accessories can be used.
3
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
•
•
•
•
•
•
•
•
•
•
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
UK and Ireland only. This appliance is fitted with
a 13 A mains plug. If it is necessary to change
the mains plug fuse, use only a 13 A ASTA (BS
1362) fuse.
This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
• Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
• It is possible to see water flowing from the drain
hose. This is due to the testing of the appliance
with the use of water in the factory.
•
You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
•
•
•
•
•
Follow the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Make sure that all metal objects are removed
from the laundry.
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Do not touch the glass door while a programme
is in operation. The glass can get hot.
SERVICE
• To repair the appliance contact an Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
•
•
•
•
Disconnect the appliance from the mains
electrical and water supplies.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the drum.
Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
INSTALLATION
WARNING! Refer to Safety chapters.
4
UNPACKING
Remove all transit bolts and packing
before you use the appliance. You are
advised to keep all transit devices so t
hat they can be refitted if the appliance
ever has to be transported again.
•
After removing all the
packaging, carefully
lay the appliance on
it’s back to remove
the polystyrene base
from the bottom.
•
Remove the power
supply cable and the
draining hose from the
hose holders on the
rear of the appliance.
POSITIONNING
• Install the machine on a flat hard floor. Make
sure that air circulation around the appliance is
not impeded by carpets, rugs etc.
• Check that the machine does not touch the wall
or other kitchen units.
• Level the appliance by
raising or lowering the
feet.
• The feet may be tight
to adjust as they incorporate a self locking nut, but the appliance MUST be level
and stable.
•
2
•
Unscrew the three
bolts.
•
Slide out the relevant
plastic spacers.
1
•
Remove the polystyrene block fitted on the
door seal. Pull out all
items from the drum.
If necessary, check the setting with a spirit level.
Any necessary adjustment can be made with a
spanner.
• After having levelled
the appliance, tighten
the lock nuts.
• Accurate levelling prevents vibration, noise
and displacement of
the appliance during
operation.
Never place cardboard, wood or
similar materials under the appliance
to compensate for any unevenness in
the floor.
WATER INLET
• The inlet hose is supplied with the appliance
and can been found inside the appliance drum.
• Do not use the hose from your previous
appliance to connect to the water supply.
This appliance must be connected toa
cold water supply.
•
•
Fill the smaller upper
hole and the two large
ones with the plastic
plug caps supplied in
the bag with the User
Manual.
•
Connect the hose
with the angled connection to the machine. Do not place
the inlet hose downwards.
45˚ • Angle the hose to the
left or right depending
35˚
on the position of your
water tap.
Set the hose correctly by loosening the ring nut.
After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.
5
•
•
Connect the hose to a
tap with a 3/4”thread.
Always use the hose
supplied with the appliance.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the tap,
you will have to purchase a new, longer hose
specially designed for this type of use.
WATER DRAINAGE
The end of the drain hose can be positioned in
three ways:
BUILDING IN
OVERVIEW
This appliance has been designed to be built into
the kitchen furniture. The recess should have the
dimensions shown in the picture below:
6
•
Hooked over the edge of a sink using the
plastic hose guide supplied with the
machine.
In this case, make sure the end cannot come
unhooked when the appliance is emptying. This
could be done by tying it to the tap with a piece
of string or attaching it to the wall.
• In a sink drain pipe branch.
This branch must be above the trap so that the
bend is at least 60 cm above the ground.
• Directly into a drain pipe at a height of not
less than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the
drainpipe must be larger than the outside
diameter of the drain hose. The drain hose must
not be kinked.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece
is available from your local Service Centre
counterclockwise with a 3mm wrench. Adjust the
height and turn the nut clockwise to fix it.
600 mm
min.
596 mm
560 mm
~10mm
555 mm
min.
830 mm
818 mm
75 mm
60 mm
170 mm
100 mm
We recommend that you keep the
packaging and the transit bolts for any
movement of the appliance.
Installing anti-tiliting device
If the height of the counter is 820 mm
or lower, you cannot install the antitilting device.
PREPARATION AND ASSEMBLY OF THE
DOOR
The appliance is originally prearranged for the
assembly of a door opening from right to left (see
picture below)
Remove the screws of the top cover on the rear of
the appliance and install the anti-tilting device as
shown in the drawing.
Adjust the anti-tilting device so that the distance
from the counter is 10mm. Loosen the nut
Door
• - width 595-598 mm
• - thickness 16-22 mm
The height X depends on the height of the adjacent
furniture's base.
7
16-22 mm
X
Ø 35 mm
416
mm
A
22±1,5 mm
14 mm
595-598 mm
Hinges
To mount the hinges drill two holes (dia. 35 mm,
depth 12.5-14 mm depending on the depth of door
furniture) on the inner side of the door.
To fix the hinges to the door use the screws for
wood 1 and 2 supplied with the appliance (see
below).
B
To align the door perfectly, loosen the screw, adjust
the door and tighten the screw A again.
The appliance is prearranged for a magnetic
closure of the door. To enable a correct operation
of this device, screw the counter-magnet A (steel
disk + rubber ring) into the inner side of the door.
Its position must correspond to the magnet B on
the appliance.
Do not remove the screw C !
1
2
A
B
The distance between the holes hobs fixing centres
must be 416 mm. The distance from upper edge of
the door to the centre of the hole depends on the
adjacent furniture's dimensions.
Door mounting
To mount the door fix the hinges to the appliance
using the M5x15 screws.
Do not remove the screw B !!
The hinges can be adjusted to compensate for
possible uneven thickness of the door.
8
C
If the door has to be opened from left to right, invert
the position of the plates E, the magnet D and the
plate C.
Mount the counter-magnet D and the hinges A as
previously described.
Do not remove the screw B!
D
A
C
E
B
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
3
4
5
6
1 Detergent dispenser
2 Control panel
•
3 Door handle
4 Rating plate
5 Drain pump filter
6 Feet for levelling the appliance
CHILD SAFETY
This device prevents children or pets to be closed
in the drum.
•
Turn the device clockwise, until the groove
is horizontal.
You cannot close the
door.
To close the door,
turn the device anticlockwise until the
groove is vertical.
INSTALLATION ON SUSPENDED FLOORING
Suspended wooden floors are particularly
susceptible to vibration.
9
To limit vibration we recommend placing a
waterproof wooden panel, at least 15 mm thick,
under the appliance. It should be screwed to at
least 2 floor beams and should extend beyond the
front feet.
If possible, install the appliance where the floor is
more stable.
CONTROL PANEL
CONTROL PANEL DESCRIPTION
1
20
19
2
1
2
18
17
900
4
16
5
15
6
7
13
4
Delay
Start
1200
3
14
3
700
Eco
500
Rinse
Hold
Quick
Wash
Door
Spin
Option
Prewash
10
9
8
Easy
Iron
Extra
Rinse
Start/Pause
6
5
8
12 11 10 9
1 Programme knob
2 Display
3 Delay Start button (Delay Start)
8 Prewash button (Prewash)
9 Options button (Option)
4 Door locked indicator
5 Start/Pause button (Start/Pause)
7
•
ECO (Eco)
•
Quick (Quick Wash)
10 Spin reduction steps (Spin)
6 Extra Rinse button (Extra Rinse)
•
Rinse Hold position (Rinse Hold)
7 Easy Iron button (Easy Iron)
DISPLAY
A
•
B
The display shows the following information:
A - Child lock indicator:
10
This device permits you to leave the appliance
unattended during it's functioning.
• When the related option is selected, the
indicator comes on the display.
B - This area shows:
• Programme time
• End of programme
• Delay start
• Alarm codes (refer to the chapter
'Troubleshooting').
• Incorrect option selection: the display shows the
message
for some seconds if:
•
You set a option that is not suitable for the
programme.
•
You change the programme while it operates.
PROGRAMMES
PROGRAMME CHART
Maximum load
Programme
Reference spin
Temperature range
speed
Programme description
(Type of load and soil level)
Cottons
1
Cottons
90°C
7 kg
1200 rpm
(ZWI 71201
WA)
1400 rpm
(ZWI 71401
WA)
White cotton and coloured cotton. Normal,
heavy and light soil.
2-3
Cottons
7 kg
1200 rpm
(ZWI 71201
WA)
1400 rpm
(ZWI 71401
WA)
White cotton and fast-coloured cotton.
Normal soil. The energy consumption decreases and the time of the washing programme is
extended, ensuring good washing results.
Cottons
30°C
7 kg
1200 rpm
(ZWI 71201
WA)
1400 rpm
(ZWI 71401
WA)
White cotton and coloured cotton. Normal,
heavy and light soil.
5
Synthetics
60°C
3 kg
900 rpm
Synthetic items or mixed fabric items.
Normal soil.
6
Synthetics
40°C
3 kg
900 rpm
Synthetic items or mixed fabric items.
Normal soil.
7
Synthetics
30°C
3 kg
900 rpm
Synthetic items or mixed fabric items.
Normal soil.
Delicates
40°C
3 kg
700 rpm
Delicate fabrics such as acrylics, viscose
and mixed fabrics requiring gentler washing. Normal soil.
1)
60°C - 40°C
4
Synthetics
Delicates
8
11
Maximum load
Programme
Reference spin
Temperature range
speed
Programme description
(Type of load and soil level)
9
Delicates
30°C
3 kg
700 rpm
Delicate fabrics such as acrylics, viscose
and mixed fabrics requiring gentler washing. Normal soil.
10 - 12
Handwash
2 kg
900 rpm
Garments with «hand washing» care symbol2).
Wool
40°C
2 kg
900 rpm
Machine washable wool and hand washable wool.
14
Jeans
40°C
3 kg
1200 rpm
Items in denim and jersey. Also for dark
coloured items.
15
Mix 20°
20°C
3 kg
900 rpm
Special programme for cotton, synthetic and
mixed fabrics lightly soiled. Select this programme to reduce the energy consumption.
Make sure that the detergent is suitable for low
temperature in order to have good washing results.
16
Soak
30°C
7 kg
Prewash - Soak for about 40 minutes - Stop
with water in the tub. Special programme for
heavily soiled laundry. At the end of this time
the appliance will stop automatically with water
left in the tub. Before starting a new washing
phase, it is necessary to empty out the water
(read "At the end of the programme")3) .
17
Mini 30'
30°C
3 kg
700 rpm
Cotton and synthetic items with light soil
level or worn only once.
18
Rinses
7 kg
1200 rpm
(ZWI 71201
WA)
1400 rpm
(ZWI 71401
WA)
To rinse and spin the laundry. All fabrics, except woollens and very delicate fabrics. Reduce the spin speed accordingly to the type of
laundry.
19
Drain
7 kg
To drain the water after programme with the
option Rinse Hold selected.
40°C 13
(Cold)
Specials
Extra
12
Maximum load
Programme
Reference spin
Temperature range
speed
20
7 kg
1200 rpm
(ZWI 71201
WA)
1400 rpm
(ZWI 71401
WA)
Spin
Programme description
(Type of load and soil level)
To spin and drain the water after programme
with the option Rinse Hold selected
Set the spin speed according to the fabric to
be spun.
For cancelling the programme which is running or switch the appliance off.
1) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, the "Cotton
" with "Eco
option and the "Cotton
" with "Eco
option are
respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme». They
are the most efficient programmes in terms of combined energy and water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly. Consider this as a normal functioning of the appliance.
3) This programme cannot be used for very delicate fabrics as silk or wool. Pour the detergent for the soak
programme into the compartment marked
. At the end of the soak (after having emptied out the water)
you can select the desired washing programme. First turn the appliance off, then select the programme
and start it.
Easy Iron4)
■
■
■
■
■
■
Synthetics
■
■
■
■
■
■
■
■
Delicates
■
■
■
■
Handwash
■
■
■
Wool
■
■
■
Jeans
■
■
Mix 20°
■
■
■
Delay Start
Prewash3)
■
Extra Rinse
Quick Wash2)
■
Rinse Hold
Cottons
Programme
Spin
Eco1)
Programme options compatibility
■
■
■
■
■
13
Delay Start
Extra Rinse
Easy Iron4)
Prewash3)
Quick Wash2)
Eco1)
Rinse Hold
Spin
Programme
■
Soak
Mini 30'
■
Rinses
■
■
■
■
■
■
Drain
■
Spin
■
1) This option is not active at a temperature lower than 40°C.
2) If you select this option we recommend that you reduce the maximum load. full loading is possible, however with somewhat reduced cleaning results.
3) If using liquid detergent, a programme without prewash must be selected.
4) if you set the Easy Iron, the recommended max load is 1.5 kg.
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
Programmes
14
Load (kg)
Energy consumption
(kWh)
Approximate
Water con- programme du- Remaining
sumption (litre) ration (mimoisture (%)1)
nutes)
Cottons
60°C
7
1.35
67
150
532) / 523)
Cottons
40°C
7
0.85
67
140
532) / 523)
Synthetics
40°C
3
0.55
42
90
352) / 353)
Delicates
30°C
3
0.55
63
65
352) / 353)
Programmes
Wool 30°C
Load (kg)
2
Energy consumption
(kWh)
Approximate
Water con- programme du- Remaining
sumption (litre) ration (mimoisture (%)1)
nutes)
0.25
55
60
302) / 303)
Standard cotton programmes
Standard
60°C cotton
7
1.01
48
216
532) / 523)
Standard
60°C cotton
3.5
0.79
44
185
532) / 523)
Standard
40°C cotton
3.5
0.62
43
180
532) / 523)
1) At the end of spin phase.
2) For model ZWI 71201 WA.
3) For model ZWI 71401 WA.
Off Mode (W)
Left On Mode (W)
0,10
0,98
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC .
OPTIONS
PROGRAMME SELECTION
This knob allows you to select a programme and/or
to switch the appliance on/off .
SPIN
With this option you can change the default spin
speed.
The indicator of the set speed comes on.
RINSE HOLD
• Set this option to prevent the laundry creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the laundry
creases.
•
The door stays locked. You must drain the water
to unlock the door.
To drain the water refer to ‘At the end
of the programme’.
ECO
With this option you can have a good washing
results and decrease the energy consumption at
the same time.
The appliance extends the wash time and reduces
the temperature.
The related indicator comes on.
15
QUICK WASH
Press this button to decrease the programme
duration.
Set this option for items with light soil or items to
refresh.
EXTRA RINSE
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related indicator comes on.
PREWASH
The machine performs a prewash cycle before the
main wash phase.
The washing time will be prolonged.
This option is recommended for heavily soiled
laundry.
DELAY START
With this option you can delay the start of a
programme from 30 minutes to 20 hours.
The display shows the related indicator.
EASY IRON
The appliance carefully washes and spins the
laundry to prevent the creases.
The appliance decreases the spin speed, uses
more water and adapts the programme duration to
the type of laundry.
The related indicator comes on.
DOOR LOCKED INDICATOR DOOR
The indicator Door shows when the door can be
opened:
• The indicator is on: the door cannot be opened.
• The indicator flashes: the door is opening in
some minutes.
• The indicator is off: the door can be opened.
SETTINGS
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
• To activate/deactivate this option, press Spin
and Option at the same time until the indicator
comes on/goes off.
You can activate this option:
• After you press Start/Pause: the options and the
programme knob are locked.
• Before you press Start/Pause: the appliance
cannot start.
ACOUSTIC SIGNALS
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
press Prewash and Easy Iron at the same time for 6
seconds.
If you deactivate the acoustic signals,
they continue to operate when the
appliance has a malfunction.
BEFORE FIRST USE
During installation or before first use
you may observe some water in the
appliance. This is residual water left in
the appliance after a full functional test
in the factory to ensure the appliance
is delivered to customers in perfect
working order and is no cause for
concern.
1. Connect the mains plug to the mains socket.
2. Open the water tap.
16
3. Put 2 litre of water in the detergent
compartment for washing phase.
This activates the drain system.
4. Put a small quantity of detergent in the
compartment for washing phase.
5. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
Compartment for liquid additives
(fabric conditioner, starch).
SETTING A PROGRAMME
1. Turn the programme knob to switch the
appliance on and set the programme:
• The indicator of the button Start/Pause
flashes.
• The display shows the programme duration.
2. If necessary, change the temperature and the
spin speed or add available options. When you
activate an option, the indicator of the set
option comes on.
If you set something incorrect, the
display shows the message
.
STARTING A PROGRAMME WITH THE DELAY
START OPTION
CAUTION! Make sure that no laundry
stays between the seal and the door.
There is a risk of water leakage or
damage to the laundry.
Washing heavily oiled, greasy stains
could cause damage rubber parts of
the washing machine.
USING DETERGENT AND ADDITIVES
1. Measure out the detergent and the fabric
conditioner.
2. Put the detergent
and the fabric conditioner into the compartments.
3. Carefully close the
detergent drawer.
DETERGENT COMPARTMENTS
Detergent compartment for prewash phase.
Detergent compartment for
washing phase.
1. Press the button Delay Start again and again
until the display shows the delay you want to
set. The delay start indicator comes on.
2. Press the button Start/Pause:
• The door is locked and the indicator Door is
on.
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
You can cancel or change the set of
the Delay Start option before you
press the button Start/Pause. After
pressing the button Start/Pause you
can only cancel the Delay Start option.
To cancel the Delay Start option:
a. Press the button Start/Pause to set the
appliance to pause. The indicator of button
Start/Pause flashes.
b. Press the button Delay Start until the
display shows .
Press the button Start/Pause again to start
the programme immediately.
STARTING A PROGRAMME WITHOUT THE
DELAY START
Press the button Start/Pause.
• The indicator of the button Start/Pause
stops to flash and stays on.
• The programme starts, the door locks, the
indicator Door is on.
17
•
The programme time decreases with steps
of one minute.
The drain pump can operate for a
short time at the beginning of the
washing cycle.
CANCELLING A RUNNING PROGRAMME
1. Turn the programme knob to position
to
cancel the programme and to deactivate the
appliance.
2. Turn the programme knob again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Press the button Start/Pause.
The indicator flashes.
2. Change the options.
3. Press the button Start/Pause again.
The programme continues.
OPENING THE DOOR
While a programme or the Delay Start operates, the
appliance door is locked. The indicator Door is on.
CAUTION! If the temperature and
level of the water in the drum are too
high and the drum still rotates, you
cannot open the door.
To open the door during the first minutes of the
cycle or when the Delay Start operates:
1. Press the button Start/Pause to pause the
appliance.
2. Wait until the indicator Door goes off.
3. You can open the door.
4. Close the door and touch the button Start/
Pause again. The programme (or the Delay
Start) continues.
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
•
•
•
In the display comes on.
The indicator of the button Start/Pause goes off.
The door lock indicator Door goes off.
Turn the programme knob to position
to
deactivate the appliance.
• You can open the door.
• Remove the laundry from the appliance. Make
sure that the drum is empty.
• Close the water tap.
• Keep the door and the detergent drawer ajar, to
prevent the mildew and odours.
The washing programme is completed, but
there is water in the drum:
• The drum turns regularly to prevent the creases
in the laundry.
• The indicator Rinse Hold stays on to remind you
to drain the water.
• The door lock indicator Door is on. The indicator
of button Start/Pause flashes. The door stays
locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Set a Drain or a Spin programme.
• Press the button Start/Pause. The
appliance drains the water and spins.
2. When the programme is completed and the
door lock indicator Door goes off, you can
open the door.
3. Turn the programme knob to the position
deactivate the appliance.
to
STAND BY
Some minutes after the end of the washing
programme, if you do not deactivate the appliance,
the energy saving status activates. The energy
saving status decreases the energy consumption
when the appliance is on the standby:
• All indicators and the display go off.
• The indicator of button Start flashes slowly.
Press one of the buttons to deactivate the energy
saving status.
HINTS AND TIPS
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
18
•
•
Obey the washing instructions that are on the
laundry care labels.
Do not wash white and coloured items together.
•
•
•
•
•
•
•
•
•
•
Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
Turn multilayered fabrics, wool and items with
painted illustrations inside out.
Remove hard stains with a special detergent.
Wash and pre-treat heavy soil stains before
putting items in drum
Be careful with the curtains. Remove the hooks
and put the curtains in a washing bag or
pillowcase.
Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
Avoid washing garments full of long animal hair
or poor quality garments releasing lots of fluff
that could block the drain circuit and therefore
requiring the Service assistance.
Empty the pockets and unfold the items.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
•
•
•
•
•
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (40
°C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
Do not mix different types of detergents.
To help the environment, do not use more than
the correct quantity of detergent.
Obey the instructions that you find on the on
packaging of these products.
Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
• Set a programme without the prewash phase to
wash laundry with normal soil.
• Always start a washing programme with the
maximum load of laundry allowed.
• If necessary, use a stain remover when you set a
programme with a low temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially
made for washing machines:
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance with soap and warm water
only. Fully dry all the surfaces.
19
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
Always obey the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
• Remove all laundry from the drum.
• Select the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
Regularly examine the
seal and remove all objects from the inner part.
•
Remove the top part of
the additive compartment to aid cleaning.
•
Make sure that all
washing powder residue is removed from
the upper and lower
part of the recess.
Use a small brush to
clean the recess.
•
•
Replace the drawer and run the rinse
programme without any clothes in the drum.
CLEANING THE DRAIN FILTER
The pump should be inspected regularly and
particularly if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during
draining phase due to objects such as safety
pins, coins and so on blocking the pump;
• a problem with water draining is detected (see
chapter 'Troubleshooting' for more details).
CAUTION! Switch the appliance off
and remove the mains plug from the
socket.
CLEANING THE DETERGENT DISPENSER
Clean regularly the washing powder and additive
dispenser drawer.
• Press the catch downwards and pull it out to
remove the drawer.
• Flush it out under a
tap, to remove any
traces of accumulated
powder.
20
Proceed as follows:
• Unplug the appliance.
• If it is necessary, wait until the water has cooled
down.
• Place a container
A B
close to the pump (A)
to collect any spillage.
• Pull out the emergency emptying hose (B),
place it in the container and remove its cap.
•
•
•
•
1
•
2
•
•
•
When no more water
comes out, unscrew
the filter.
Turn the filter anticlockwise.
Remove the filter.
Use pliers, if necessary.
When removing the
filter, always keep a
rag nearby to dry up
any water spillage.
Clean the filter under
a tap, to remove any
traces of fluff.
Remove foreign
bodes and fluff from
the filter seat and from
the pump impeller.
Check carefully
whether the pump impeller rotates (it rotates jerkily).
CLEANING THE INLET HOSE AND THE VALVE
FILTER
If the appliance doesn't fill, take long to fill with
water, the starting button blinks or the display (if
available) shows the relevant alarm (see chapter
'Troubleshooting' for more details), check if the
water inlet filters are blocked.
To clean the water inlet filters:
• Turn off the water tap.
• Unscrew the hose
1
from the tap.
• Clean the filter in the
2
hose with a stiff brush.
3
•
Screw the hose back onto the tap. Make sure
the connection is tight.
• Unscrew the hose
from the machine.
• Keep a rag nearby because some water
may flow.
If it doesn’t rotate, please contact your Service
Centre.
• Put the cap back on
the emergency emptying hose and place
2
the latter back in its
seat.
• Replace the filter into
the pump, insert it
correctly into the spe1
cial guides.
•
•
Clean the filter in the
valve with a stiff brush
or with the piece of
cloth.
•
Screw the hose back
to the machine and
make sure the connection is tight.
Turn on the water tap.
Screw the pump cover firmly. Turn it clockwise.
CAUTION! When the appliance is in
use and depending on the set
programme there can be hot water in
the pump.
Never remove the filter during a washing cycle,
always wait until the appliance has finished the
cycle, and is empty.
When refitting the filter, ensure it is securely retightened so as to stop leaks and young children
being able to remove it.
•
45°
20°
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0° C, remove the
remaining water from the inlet hose and the drain
pump.
1. Disconnect the mains plug from the mains
socket.
21
2. Close the water tap.
3. Place the end of the emergency emptying hose
and that of the inlet hose in a bowl placed on
the floor and let water flow out of the hoses.
4. Set the Drain programme and let it operate until
the end of the cycle.
5. Turn the programme knob to
to disconnect
the appliance from the power supply.
6. Screw the water inlet hose back on and re-fit
the emergency emptying hose after having put
the cap on again.
WARNING! Make sure that the
temperature is more than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. If necessary, wait until the water has cooled
down.
4. Place a bowl on the floor and put the end of
the emergency emptying hose into the bowl.
Remove its cap.
The water should drain by gravity into the bowl.
5. When the bowl is full, put the cap back on the
emergency hose.
6. Empty the bowl. Repeat the procedure until
water stops flowing out.
7. Clean the pump if necessary as previously
described.
8. Replace the emergency emptying hose in its
seat after having plugged it.
9. Screw the water inlet hose back on.
EMERGENCY EMPTYING OUT
If the appliance does not drain the water, proceed
as follows:
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during
operation.
First try to find a solution to the problem (refer to
the table). If the problem persists, contact the
Authorised Service Centre.
With some problems, the acoustic signals
operate and the display shows an alarm
code:
•
22
- The appliance does not fill with water
properly. Start the appliance again by pressing
Start/Pause button. After 10 seconds the door
will be unlocked.
•
- The appliance does not drain the water.
•
- The appliance door is open or not
closed correctly. Please check the door!
•
- The mains supply is unstable. Wait until
the mains supply is stable.
•
- No communication between electronic
elements of the appliance. Switch off and
switch on again. The programme was not
finished properly or the appliance stopped too
early. If the alarm code appears again, contact
the Authorised Service Centre.
WARNING! Deactivate the appliance
before you do the checks.
POSSIBLE FAILURES
Problem
The programme does not
start.
Possible solution
•
•
•
•
•
•
The appliance does not fill
with water properly.
•
•
The appliance does not
drain the water.
•
•
•
•
•
•
•
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the fuse box.
Make sure that the Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of
countdown.
Deactivate the Child Lock function if it is on (if available).
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'.
Make sure that the drain hose is in the correct position. The hose
may be too low.
Set the drain programme if you set a programme without drain
phase.
Set the drain programme if you set an option which ends with water
in the tub.
The spin phase does not
operate or the washing cycle lasts longer than usually.
•
•
Set the spin programme.
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
There is water on the floor.
•
•
Make sure that the couplings of the water hoses are tight and there
is not water leakages.
Make sure that the drain hose have no damages.
Make sure you use the correct detergent and the correct quantity of
it.
Make sure you have replaced the emergency emptying cap into the
filter
Make sure you have properly screwed the filter in after cleaning.
You cannot open the appliance door.
•
•
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
The appliance makes an
unusual noise.
•
Make sure the levelling of the appliance is correct. Refer to 'Installation'.
Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation'.
Add more laundry in the drum. The load may be too small.
•
•
•
•
•
The washing results are
not satisfactory.
You cannot set an option.
•
•
•
•
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
•
Make sure that you press only the wanted button(s).
23
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Authorised
Service Centre.
If the display shows other alarm codes. Deactivate
and activate the appliance. If the problem
continues, contact the Service.
SERVICE
We recommend the use of original spare parts.
When contacting the Authorised Service Centre,
make sure that these data are available. You can
find the information on the rating plate: model, PNC
and Serial Number. (Mod., Prod. No., Ser. No.)
TECHNICAL DATA
Dimension
Width/ Height/ Depth/ Total depth
596 mm/ 820 mm/ 544 mm/ 560 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
230-240 V
2050
13 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Minimum
Maximum
Cold water
Water supply 1)
Maximum Load
Cotton
7 kg
Energy Efficiency Class
Spin Speed
A++
Maximum spin speed
1151 rpm (ZWI 71201 WA)
1351 rpm (ZWI 71401 WA)
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
PRODUCT INFORMATION SHEET IN REFERENCE TO E.U. REGULATION
1369/2017
Product Information Sheet
Trade Mark
Model
Rated capacity in kg
24
ZANUSSI
ZWI71201WA,
PNC914528134
7
Energy efficiency class
A++
Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and
partial load, and the consumption of the low-power modes. Actual
energy consumption will depend on how the appliance is used.
189
Energy consumption of the standard 60°C cotton programme at full
load in kWh
1.01
Energy consumption of the standard 60°C cotton programme at partial load in kWh
0.79
Energy consumption of the standard 40°C cotton programme at partial load kWh
0.62
Power consumption of the off-mode in W
0.10
Power consumption in left-on mode in W
0.98
Water consumption in litres per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and
partial load. Actual water consumption will depend on how the appliance is used.
Spin-drying efficiency class on a scale from G (least efficient) to A
(most efficient)
Maximum spin speed in rpm
10469
B
1151
Remaining moisture content in %
53
The 'standard 60 °C cotton programme' and the 'standard 40 °C
cotton programme' are the standard washing programmes to which
the information in the label and the fiche relates, these programmes
are suitable to clean normally soiled cotton laundry and they are the
most efficient in terms of combined energy and water consumption.
-
Programme time of the standard 60°C cotton programme at full load
in minutes
216
Programme time of the standard 60°C cotton programme at partial
load in minutes
185
Programme time of the "standard 40°C cotton programme at partial
load in minutes
180
Duration of the left on mode in minutes
5
Airborne acoustical noise emission in db(A) washing
56
Airborne acoustical noise emission in db(A) spinning
72
Built in appliance Y/N
Yes
The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC .
Product Information Sheet
Trade Mark
Model
Rated capacity in kg
ZANUSSI
ZWI71401WA,
PNC914528135
7
Energy efficiency class
A++
Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and
partial load, and the consumption of the low-power modes. Actual
energy consumption will depend on how the appliance is used.
189
25
Energy consumption of the standard 60°C cotton programme at full
load in kWh
1.01
Energy consumption of the standard 60°C cotton programme at partial load in kWh
0.79
Energy consumption of the standard 40°C cotton programme at partial load kWh
0.62
Power consumption of the off-mode in W
0.10
Power consumption in left-on mode in W
0.98
Water consumption in litres per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and
partial load. Actual water consumption will depend on how the appliance is used.
Spin-drying efficiency class on a scale from G (least efficient) to A
(most efficient)
Maximum spin speed in rpm
10469
B
1351
Remaining moisture content in %
52
The 'standard 60 °C cotton programme' and the 'standard 40 °C
cotton programme' are the standard washing programmes to which
the information in the label and the fiche relates, these programmes
are suitable to clean normally soiled cotton laundry and they are the
most efficient in terms of combined energy and water consumption.
-
Programme time of the standard 60°C cotton programme at full load
in minutes
216
Programme time of the standard 60°C cotton programme at partial
load in minutes
185
Programme time of the "standard 40°C cotton programme at partial
load in minutes
180
Duration of the left on mode in minutes
5
Airborne acoustical noise emission in db(A) washing
56
Airborne acoustical noise emission in db(A) spinning
74
Built in appliance Y/N
Yes
The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC .
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
26
*
27
132908194-A-032019
WWW.ZANUSSI.COM/SHOP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement