ZANUSSI Z712W43BI User Manual
User Manual
GETTING
STARTED?
EASY.
Z712W43BI
EN User Manual
Washing Machine
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
•
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
If the appliance has a child safety device, it should be activated.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
2
Do not change the specification of this appliance.
This appliance is intended to be used in household and similar
applications such as:
– staff kitchen areas in shops, offices and other working
environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments;
•
•
•
•
•
•
•
•
•
– areas for communal use in blocks of flats or in launderettes.
Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
•
•
•
•
•
•
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Follow the installation instructions supplied with
the appliance.
Do not use the appliance before installing it in
the built-in structure due to safety manner.
Do not install or use a damaged appliance.
•
•
•
•
•
•
•
•
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
Make sure that there is air circulation between
the appliance and the floor.
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
Do not install the appliance directly above a
floor drain.
Do not spray water on the appliance and do not
expose it to excessive humidity.
Do not install the appliance where the appliance
door cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the appliance.
3
Contact the Authorised Service Centre to
ensure which accessories can be used.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
•
•
•
•
•
•
•
•
•
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
• Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
• When unpacking the appliance, It is possible to
see water flowing from the drain hose. This is
due to the testing of the appliance with the use
of water in the factory.
•
•
You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
Make sure that there is access to the tap after
the installation.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
•
•
•
•
•
Follow the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Do not touch the glass door while a programme
operates. The glass can get hot.
Make sure that all metal objects are removed
from the laundry.
SERVICE
• To repair the appliance contact the Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
•
•
•
•
Disconnect the appliance from the mains
electrical and water supplies.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the drum.
Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
INSTALLATION
WARNING! Refer to Safety chapters.
4
BE PREPARED FOR INSTALLATION
It is recommended that installation is
carried out by two persons.
THE APPLIANCE IS EQUIPPED WITH ...
A
B
C
D
E
x4
x2
x1
x1
x1
F
G
H
L
x1
x2
x1
x1
x1
x2
UNPACKING
WARNING! Use the gloves.
WARNING! Remove all the packaging and the transit bolts before installing the appliance.
1. Put two polystyrene packaging elements on
the floor under the appliance.
WARNING! It is strongly recommended that this action is carries
out by two persons.
2. Carefully put the appliance down on its rear
side.
Make sure not to damage the hoses.
3. Remove the polystyrene protection from the
bottom.
1
2
5
4. Return the appliance in vertical position and
remove the socket polystyrene protection.
1
2
5. Remove the power supply cable and the drain
hose from the hose holders.
It is possible to see water flowing
from the drain hose. This is due to
the testing with water of the appliance in factory.
6. Remove the three bolts, the hose holders and
plastic spacers by using the spanner supplied
with the appliance.
F
7. Close the holes with the plastic caps you find
in the user manual bag. Put the smallest cap F
in upper hole and the two bigger caps G in lower holes.
G
We recommend that you keep the packaging and the transit bolts for any movement of the
appliance.
INSTALLATION ON SUSPENDED FLOORING
Suspended wooden floors are particularly
susceptible to vibration.
6
To limit vibration we recommend placing a
waterproof wooden panel, at least 15 mm thick,
under the appliance. It should be screwed to at
least 2 floor beams and should extend beyond the
front feet.
If possible, install the appliance where the floor is
more stable.
POSITIONING AND LEVELLING
1. Install the appliance on a flat hard floor.
WARNING! Make sure that carpets do
not stop the air circulation below the appliance.
Bring the appliance near the furniture
recess before levelling it. For more details, refer to paragraph "Building in".
2. Loosen or tighten the feet to adjust the level.
x4
A correct adjustment of the appliance
level prevents the vibration, noise and
the movement of the appliance when in
operation.
The appliance must be level and stable.
CAUTION! Do not put cardboard, wood
or equivalent materials below the appliance feet to adjust the level.
HOSE AND CABLE CONNECTION
900 mm
760 mm
1360 mm
max 1000 mm
min. 600 mm
max 1000 mm
1020 mm
1450 mm
min. 600 mm
1100 mm
7
The inlet hose
1. Remove the inlet hose from inside the drum.
2. To connect the water inlet hose towards the proper direction and with the proper inclination, check the
position of the water tap before connecting it to the
back of the appliance.
Make sure the hose is nor kinked,
squashed but neither tensed.
3. Connect the hose to the back of the appliance. Do
not turn the inlet hose downwards, but turn it left or
right depending on the position of your water tap.
4. Loosen the ring nut to fix it in the correct position.
45
20
O
O
5. Connect the water inlet hose to the cold water tap
with 3/4 thread.
WARNING! Make sure that there are no
leaks from the couplings.
Use the hose supplied with appliance.
Do not use an extension hose if the inlet hose is too short. Contact the Authorised Service
Centre for an inlet hose replacement.
Water drainage
The drain hose can be connected:
8
To a stand pipe with vent-hole
Directly into a drain pipe at a height of not less than
60 cm (23.6”) and not more than 100 cm (39.3”).
The end of the drain hose must always be ventilated ,
i.e. the inner diameter of the drain pipe (min. 40 mm min. 1.6”) must be larger than the external diameter
of the drain hose.
Ø 40 mm
max.600 mm
To a sink spigot
Put the drain hose in the spigot and tighten it with
the supplied cable tie L.
Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink.
L
To a wall-pipe
Directly to a built-in drain pipe in the room wall and
tighten it with the supplied cable tie L.
You can extend the drain hose to maximum 400 cm. Contact the service centre for the other
drain hose and the extension.
BUILDING IN
This appliance has been designed to be built into the
kitchen furniture. The recess should have the dimensions shown in this picture.
min. 600 mm
For recess with a height different than
820 mm, it is possible to buy the appropriate kit on the website.
min.
560 mm
min.
820 mm
16-22 mm
9
596 mm
If hoses run behind the appliance, make
sure that nothing closes the small recess indicated with the measures 50 x
50 mm.
553 mm
819 mm
50 mm
50 mm
140 mm
76 mm
The appliance is also equipped with an adhesive
sponge pad H that you can find inside the drum.
Attach it on the top of the appliance where indicated
in the drawing.
When levelling the appliance under the furniture, DO
NOT squeeze the sponge pad.
Before proceeding with appliance building in, bring it
near the recess and preposition the inlet hose, the
drain hose and the mains cable.
WARNING! Make sure they are not
kinked or squashed.
INSTALLING ANTI-TILTING DEVICE
(ACCESSORY)
Install this accessory in case of risk of appliance tilting only.
If the height of the counter is 820 mm or lower, you cannot install the anti-tilting device.
10
1. Remove the screws of the top cover on the rear of
the appliance and install the anti-tilting device as
shown in the drawing.
~10mm
2. Adjust the anti-tilting device so that the distance
from the counter is 10mm. Loosen the nut counterclockwise with a 3mm wrench. Adjust the height and
turn the nut clockwise to fix it.
PREPARATION AND ASSEMBLY OF THE CUPBOARD DOOR
The dimensions of the cupboard door should be:
• width min. 595 - max. 598 mm;
• thickness 16-22 mm.
Factory pre setting
The appliance is originally pre set for the assembly of
a cupboard door opening from right to left.
The best solution would be to screw
the upper hinge to the upper hole of the
top plate and the lower hinge to the
lower hole of the bottom plate.
11
Reversibility of the cupboard door
Carry out the cupboard door reversibility before the
appliance is built in completely.
N
If the cupboard door has to be opened from left to
right, invert the position of the hinge supports M with
the magnetic plate N and lower plate O.
M
O
M
N
Make sure that the plate with magnet is
on the upper position.
O
Cupboard door preparation
For countersinking the door, it is recommended to call a professional.
y
x
y
12
Align the cupboard door to the furniture correctly.
Measure the distance X to fix the height of the hole
to countersink the upper hinge. The centre of the
hole Y should be at the same height of the stroke on
the hinge support.
Set the position of the lower hole respecting dimensions and distances shown in the drawing (449
mm).
Countersink the holes.
16-22 mm
Ø 35 mm
449
mm
12,5 - 14 mm
22±1,5 mm
595-598 mm
Hinges
To mount the hinges it is necessary to drill two holes
(dia. 35 mm, depth 12.5 - 14 mm depending on the
depth of cupboard door) on the inner side of the
door.
The hinges will be fixed to the door by means of the
four supplied screws A.
A
To align the door perfectly, make sure
that the edge of cupboard door is parallel with the appliance edge and to respect the proper opening angle (max.
105 °).
max. 105°
Mounting the door
Fix the hinges to the hinge supports on the appliance by means of the two supplied screws B.
The hinges can be adjusted to compensate for possible uneven thickness of
the door.
13
Counter-magnet
The appliance is pre set for a magnetic closure.
For a correct closure:
1. Position the screw C and the counter-magnet D
on the magnetic plate N. Lean the cupboard
door against the screw until it leaves a mark.
2. Open the cupboard door and screw the counter-magnet D (steel disk + rubber ring E) with
the screw C in the inner side of the cupboard
door, where the screw left the mark as described in the first step.
1
N
2
E
D
C
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
10
3
11 12
4
5
6
7
8
9
13
1 Hinge supports
2 Detergent dispenser
8 Drain pump filter
9 Front feet for levelling the appliance
3 Control panel
4 Magnetic plate
10 Drain hose
11 Mains cable
5 Door handle
6 Rating plate
12 Inlet hose connection
13 Back feet for levelling the appliance
7 Plate with rubber beater
14
CONTROL PANEL
CONTROL PANEL DESCRIPTION
1
2
Wool/
Handwash
3
4
Cottons
Denim
Cottons Eco
Sport
Synthetics
Delay Start
Delicates
20min 3kg
Duvet
Easy Iron
Machine Clean
Mixed
Rinse
Temp.
Spin
Prewash
Spin/Drain
On/Off
10
The permanent options are set by
holding pressed the relative button for
3 seconds at least.
1 Programme dial
2 Display
3 Flextime touch button
4 Delay Start touch button
5 Start/Pause touch button
6 Prewash touch button and permanent Extra
9
8
7
6
5
7 Spin reduction options touch button and
permanent Child Lock option
8 Temp. touch button
9 On/Off push button
10 Option indicators:
• Rinse Hold
• Quiet
• Extra Rinse
Rinse option
15
DISPLAY
A
Door locked indicator.
A B
C
B
Child safety lock indicator.
C
The digital indicator can show:
• Programme duration: e. g.
.
•
Delay time: e. g.
•
Cycle end:
•
Warning code: e.g.
•
Temperature:
•
Spin speed:
dicator
.
.
.
.
and no spin in.
DIAL AND BUTTONS
INTRODUCTION
The options/functions are not available
with all washing programmes. Check
the compatibility between options/
functions and washing programmes in
the "Programme Chart". An option/
function can exclude another one, in
this case the appliance doesn't allow
you to set incompatible options/
functions.
FLEXTIME
This option may be advisable to shorten the
washing programme.
Use this option for items with normal or light soil or
items to refresh.
Touch this button once to decrease the duration.
In case of smaller load, touch this button twice to
set an extra quick programme.
After each touching the new programme duration is
shown on the display. The relevant indicator
illuminates. This option is not available for every
programme. For more details, refer to Programme
options compatibility in "Programmes" chapter.
DELAY START
With this option you can delay the start of a
programme to a more convenient time.
16
Touch the button repeatedly to set the required
delay. The time increases in steps of 1 hour up to
20 hours.
After touching the Start/Pause
button, the
relevant indicator illuminates and the selected delay
time and the appliance begins the countdown. The
door is locked.
START/PAUSE
Touch the Start/Pause
button to start, pause
the appliance or interrupt a running programme.
PREWASH
With this option you can add a prewash phase to a
washing programme.
The relevant indicator illuminates.
• Use this option to add a pre-wash phase at 30
°C before the washing phase.
This option is recommended for heavily soiled
laundry, especially if containing sand, dust, mud
and other solid particles.
This option can increase the
programme duration.
PERMANENT EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
To activate/deactivate this option , hold down
the Prewash button until relevant indicator
comes on/goes off.
•
SPIN
When you set a programme, the appliance
automatically sets the maximum spin speed allowed
except programme Denim.
Push this button to set additional spin
options:
• Decrease the spin speed. The display shows
only the spin speeds available for the set
programme.
are available. In some programmes the rinses
are performed with more water.
button, the
If you touch the Start/Pause
appliance performs only the draining phase.
The appliance empties the water out
automatically after approximately 18
hours.
CHILD LOCK
With this option you can prevent children from
playing with the control panel.
• To activate/deactivate this option, hold down
the Spin button until
comes on/goes off
on the display.
The appliance will default to this option after you
switch it off.
The Child Lock function may not be available for a
few seconds after switching the appliance on.
•
No spin
comes on display.
Set this option to deactivate all spin phases.
The appliance performs only the draining phase
of the selected washing programme. Set this
option for very delicate fabrics. The rinse phase
uses more water for some washing programmes
•
Rinse hold
. The related indicator comes
on.
The final spin is not performed. The water of the
last rinse is not drained out to prevent the
fabrics from creasing. The washing programme
ends with water in the drum.
The door stays locked and the drum turns
regularly to reduce creasing. You must drain the
water to unlock the door.
TEMP.
When you select a washing programme, the
appliance automatically proposes a default
temperature.
Touch this button repeatedly until the desired
temperature value appears on the display.
When the display shows the indicators
, the
appliance does not heat the water.
If you touch the Start/Pause
button, the
appliance performs the spinning phase and
drains the water.
ON/OFF
Press this button for a few seconds to activate or
deactivate the appliance. Two different tunes sound
while switching the appliance on or off.
As the Stand-by function automatically deactivates
the appliance after several minutes to reduce the
energy consumption, you may need to activate the
appliance again.
For more details, refer to Stand-by paragraph in
Daily Use chapter.
•
Quiet
. The related indicator comes on.
The intermediate and the final spinning phases
are suppressed and the programme ends with
water in the drum. This helps to reduce
creasing. The door stays locked. The drum turns
regularly to reduce creasing. You must drain the
water to unlock the door.
As the programme is very quiet, it is suitable for
use at night time when cheaper electricity tariffs
17
PROGRAMMES
PROGRAMME CHART
Programme
Reference
Default tempera- spin speed
Maximum
ture
Spin speed
load
Temperature
range
range
(rpm)
1200 rpm
(1200 400)
7 kg
White cotton and coloured cotton. Normal and
heavy soil.
1200 rpm
(1200 400)
7 kg
White cotton and fast-coloured cotton. Normal
soil. The energy consumption decreases and the time
of the washing programme is extended, ensuring good
washing results.
1200 rpm
(1200 400)
3 kg
Synthetic items or mixed fabric items. Normal
soil.
1200 rpm
(1200 400)
2 kg
Delicate fabrics such as acrylics, viscose and
mixed fabrics requiring gentler washing. Normal
soil.
800 rpm
(800 400)
3 kg
Synthetic items requiring a gentle wash. Normal
and light soil.2)
1200 rpm
(1200 400)
3 kg
Synthetic and mixed fabrics. Normally soiled.
1200 rpm
(1200 400)
7 kg
Spin/Drain
All fabrics, except woollens and delicate fabrics. To spin the laundry and to drain the water in the
drum.
1200 rpm
(1200 400)
7 kg
Rinse
All fabrics, except woollens and very delicate
fabrics. Programme for rinsing and spinning the laundry. The default spin speed is the one used for cotton
programmes. Reduce the spin speed according to the
type of laundry. If necessary, set the Extra Rinse option
to add rinses. With a low spin speed, the appliance
performs delicate rinses and a short spin.
Cottons
40 °C
90 °C - Cold
Eco1)
Cottons
40 °C
60 °C - 40 °C
Synthetics
40 °C
60 °C - Cold
Delicates
30 °C
40 °C - Cold
Easy Iron
40 °C
60 °C - Cold
Mixed
30 °C
40 °C - Cold
18
Programme description
(Type of load and soil level)
Programme
Reference
Default tempera- spin speed
Maximum
ture
Spin speed
load
Temperature
range
range
(rpm)
1200 rpm
-
Machine Clean
60 °C
Programme description
(Type of load and soil level)
Maintenance cycle with hot water to clean and freshen
the drum and to remove residue that may cause odour.
For the best result use this cycle once a month. Before
running this cycle, remove all items from the drum. In
the washing phase compartment of the detergent dispenser, put the flap of the compartment in upward position. Pour a cup of chlorine bleach or a washing machine cleaner in the washing phase compartment. DO
NOT use both together.
After the drum cleaning, run a further
rinse cycle with empty drum and no detergent to remove any residue of bleach.
Duvet
40 °C
60 °C - Cold
20min 3kg
30 °C
40 °C - 30 °C
Sport
30 °C
40 °C - Cold
Denim
30 °C
40 °C - Cold
800 rpm
(800 400)
3 kg
Single synthetic blanket, padded clothes, duvets, down jackets and similar items.
1200 rpm
(1200400 rpm)
3 kg
Cotton and synthetic items lightly soiled or once
worn.
1200 rpm
(1200 400)
3 kg
Mixed fabric sportswear. Light soil items or items to
refresh.
800 rpm
(1200 400)
3 kg
Special programme for Denim clothing with delicate washing phase to minimize colour fading
and marks. For better care a reduced load size is
recommended.
19
Programme
Reference
Default tempera- spin speed
Maximum
ture
Spin speed
load
Temperature
range
range
(rpm)
Wool/Handwash
40 °C
40 °C - Cold
1200 rpm
(1200 400)
1.5 kg
Programme description
(Type of load and soil level)
Machine washable wool, hand washable wool
and other fabrics with «hand washing» care symbol3).
1) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and
water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin
phase. The appliance adds some rinses.
3) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
Synthetics
Delicates
Easy Iron
Mixed
20
Flextime
Cottons Eco
Delay Start
Cottons
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Spin
Programme
Prewash
Programme options compatibility
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Spin/Drain
Rinse
Machine Clean
Duvet
20min 3kg
Sport
Denim
Wool/Handwash
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Flextime
Delay Start
Prewash
Spin
Programme
■
■
■
■
■
■
■
■
■
■
■
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
Programmes
Cottons
60°C
Approximate Remaining
Energy con- Water conprogramme moisture
Load (kg) sumption sumption (liduration
(kWh)
tre)
(%)1)
(minutes)
7
1.20
79
190
53
21
Approximate Remaining
Energy con- Water conprogramme moisture
Load (kg) sumption sumption (liduration
(kWh)
tre)
(%)1)
(minutes)
Programmes
Cottons
40°C
7
1.00
80
180
53
Synthetics
40°C
3
0.69
72
135
35
Delicates
40°C
2
0.43
46
55
35
1.5
0.14
60
70
30
Standard 60°C cotton
7
0.93
52
250
53
Standard 60°C cotton
3.5
0.70
41
205
53
Standard 40°C cotton
3.5
0.55
41
200
53
Wool/Handwash
30°C
Standard cotton programmes
1) At the end of spin phase.
Off Mode (W)
0.48
Left On Mode (W)
0.48
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC .
SETTINGS
ACOUSTIC SIGNALS
This appliance has different acoustic signals, that
operate when:
• You activate the appliance (special short tune).
• You deactivate the appliance (special short
tune).
• You touch the buttons (click sound).
• You make an invalid selection (3 short sounds).
• The programme is completed (sequence of
sounds for about 2 minutes).
• The appliance has a malfunction (sequence of
short sounds for about 5 minutes).
22
To deactivate/activate the acoustic signals when
the programme is completed, touch the Flextime
and the Delay Start buttons simultaneously for
about 2 seconds. The display shows On/Off
If you deactivate the acoustic signals,
they continue to operate when the
appliance has a malfunction.
BEFORE FIRST USE
1. Make sure that the electrical power is available
and the water tap is open.
2. Pour 2 litres of water into the detergent
.
compartment marked by
This action activates the drain system.
3. Pour a small quantity of detergent into the
compartment marked by
4. Set and start a programme for cotton at the
highest temperature without any laundry in the
drum.
This removes all possible dirt from the drum and the
tub.
.
DAILY USE
WARNING! Refer to Safety chapters.
FILLING THE DETERGENT AND ADDITIVES
ACTIVATING THE APPLIANCE
1. Connect the mains plug to the mains socket.
2. Open the water tap.
3. Press the On/Off button for a few seconds to
activate the appliance.
A short tune sounds.
LOADING THE LAUNDRY
1. Open the appliance door.
2. Empty the pockets and unfold the items before
you put them in the appliance.
3. Put the laundry in the drum, one item at a time.
Do not put too much laundry in the drum.
4. Close the door firmly.
- Compartment for prewash phase, soak
programme or stain remover.
- Compartment for washing phase.
- Compartment for fabric softener and other
liquid treatments(fabric conditioner, starch).
- Maximum level for quantity of liquid additives.
- Flap for powder or liquid detergent.
CAUTION! Make sure that no laundry
gets caught between the seal and the
door to avoid risk of water leakage and
damage to the laundry.
Washing heavily oiled, greasy stains
could cause damage to rubber parts
of the washing machine.
Always follow the instructions that you
find on the packaging of the detergent
products, but we recommend that you
do not exceed the maximum indicated
level (
). This quantity will
however guarantee the best washing
results.
After a washing cycle, if necessary,
remove any detergent residue from the
detergent dispenser.
23
CHECK THE POSITION OF THE DETERGENT
FLAP
1. Pull out the detergent dispenser until it stops.
SETTING A PROGRAMME
1. Turn the programme dial to select the desired
washing programme.
The indicator of the Start/Pause
button flashes.
The display shows an indicative programme
duration.
2. To change the temperature and/or the spin
speed, touch the related buttons.
3. If desired, set one or more options by touching
the related buttons.
If a selection is not possible an
acoustic signal sounds.
STARTING A PROGRAMME
2. Press the lever down to remove the dispenser.
3. To use powder detergent, turn the flap up.
4. To use liquid detergent, turn the flap down.
Touch the Start/Pause
button to start the
programme. It is not possible to start the
programme when the indicator of the button is off
and doesn't flash (e.g. programme dial on a wrong
position).
The related indicator stops flashing and stays on.
The programme starts, the door is locked. The
display shows the indicator
.
STARTING A PROGRAMME WITH THE DELAY
START
1. Touch the Delay Start button until the display
shows the desired delay time. The related indicator
comes on.
With the flap in the position DOWN:
• Do not use gelatinous or thick liquid
detergents.
• Do not exceed to liquid detergent dose
indicated on the flap.
• Do not set the prewash phase.
• Do not set the delay start function.
5. Measure out the detergent and the fabric
conditioner.
6. Carefully close the detergent dispenser.
2. Touch the Start/Pause
button. The appliance
door locks and starts the countdown of the delay
start. The display shows the indicator
.
When the countdown is completed, the programme
starts automatically.
Cancelling the delay start after the
countdown has started
To cancel the delay start:
1. Touch the Start/Pause
button to pause the
appliance. The related indicator flashes.
2. Touch the Delay Start button repeatedly until
the display shows
.
3. Touch the Start/Pause
button again to
start the programme immediately.
Changing the delay start after the countdown
has started
To change the delay start:
1. Touch the Start/Pause
button to pause the
appliance. The related indicator flashes.
Make sure that the flap does not cause a blockage
when you close the drawer.
24
2. Touch the Delay Start button repeatedly until
the display shows the desired delay time.
OPENING THE DOOR - ADDING GARMENTS
If the temperature and level of the
water in the drum are too high and/or
the drum is still rotating you should not
open the door.
3. Touch the Start/Pause
button again to
start the new countdown.
THE AUTOADJUST SYSTEM LOAD
DETECTION
After touching the Start/Pause
button:
1. The AutoAdjust System starts estimating the
weight of the load to calculate the real
programme duration. During this phase the two
dots separating hours from minutes are
blinking.
2. After about 15-20 minutes new cycle duration
is displayed.
The appliance automatically adjusts the
programme duration to the load to achieve
perfect washing results in the minimum
possible time.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
When the programme is running, you can change
only some options:
1. Touch the Start/Pause
button.
The related indicator flashes.
2. Change the options. The given information in
the display changes accordingly.
3. Touch the button Start/Pause
The washing programme continues.
again.
CANCELLING A RUNNING PROGRAMME
1. Press the button On/Off to cancel the
programme and to deactivate the appliance.
2. Press the button On/Off again to activate the
appliance.
If the AutoAdjust System has
completed and the water filling has
already started, the new programme
starts without repeating the
AutoAdjust System. The water and
the detergent are not drained out in
order to avoid waste.
There is also an alternative way of cancelling:
1. Rotate the selector knob to the "Reset" position
.
2. Wait for 1 second. The display shows
.
Now, you can set a new washing programme.
While a programme or the delay start operates, the
appliance door is locked. The display shows the
indicator
.
1. Touch the Start/Pause
button.
In the display the related door lock indicator goes
off.
2. Open the appliance door. If necessary, add or
remove the items. Close the door and touch
button.
the Start/Pause
The programme or the delay start continues.
END OF THE PROGRAMME
When the programme has finished, the appliance
stops automatically. The acoustic signals operate (if
they are active). The display shows
The indicator of the Start/Pause
off.
button goes
The door unlocks and the indicator
goes off.
1. Press button On/Off to deactivate the
appliance.
After five minutes from the end of the programme,
the energy saving function automatically
deactivates the appliance.
When you activate the appliance
again, the display shows the end of
the previous programme. Turn the
programme dial to set a new cycle.
2. Remove the laundry from the appliance.
3. Make sure that the drum is empty.
4. Keep the door and the detergent dispenser
slightly ajar to prevent mildew and odours.
DRAINING WATER OUT AFTER END OF
CYCLE
If you have chosen a programme or an option that
does not empty out the water of the last rinse, the
programme is completed, but:
•
The time area shows
•
The indicator of the Start/Pause
button
starts flashing.
The drum still turns at regular intervals to
prevent creases in the laundry.
The door stays locked.
shows the door locked
•
•
and the display
.
25
• You must drain the water to open the door:
1. If necessary, touch the Spin button to decrease
the spin speed proposed by the appliance.
•
2. Press the Start/Pause
button: the
appliance drains the water and spins.
•
The option indicator Rinse Hold
disappears.
or
If you have set Quiet
and the spin
speed is not changed, when you press
the Start/Pause
button, the
appliance only drains the water.
3. When the programme is completed and the
You do not use the appliance for 5 minutes
when no programme is running.
Press the button On/Off to activate the
appliance again.
5 minutes after the end of the washing
programme.
Press the On/Off button to activate the
appliance again.
The display shows the end of the last
programme.
Turn the programme dial to set a new cycle.
If the dial is rotated to the "Reset" position
, the
appliance automatically turns off in 30 seconds.
If you set a programme or an option
that ends with water in the drum, the
Stand-by function doesn't
deactivate the appliance to remind
you to drain the water.
door locked indicator
goes off, you can
open the door.
4. Press the On/Off button for a few seconds to
deactivate the appliance.
STAND-BY FUNCTION
The Stand-by function automatically deactivates the
appliance to reduce the energy consumption when:
HINTS AND TIPS
WARNING! Refer to Safety chapters.
THE LAUNDRY LOAD
• Divide the laundry into: white, coloured,
synthetics, delicates and wool.
• Follow the washing instructions on the laundry
care labels.
• Do not wash white and coloured items together.
• Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first couple of times.
• Turn multilayered fabrics, wool and items with
printed illustrations inside out.
• Pre-treat tough stains.
• Wash heavy soil stains with a special detergent.
• Be careful with curtains. Remove the hooks and
put the curtains in a washing bag or pillowcase.
• Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, shoelaces, ribbons, etc. ).
• A very small load can cause balance problems
with the spin phase leading to excessive
vibration. If this occurs:
a. interrupt the programme and open the
door (refer to "Daily Use" chapter);
26
•
•
b. manually redistribute the load so that the
items are spaced evenly around the tub;
c. press the Start/Pause button. The spin
phase continues.
Button up pillowcases, close zippers, hooks and
poppers. Tie up belts, cords, shoelaces, ribbons
and any other loose elements.
Empty pockets and unfold the items.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND OTHER TREATMENTS
• Only use detergents and other treatments
specially made for washing machines:
– powder detergents for all types of fabric,
excluding delicate. Prefer powder
detergents containing bleach for whites and
laundry sanitization
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special ones for
woollens only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the recommended quantity of detergent.
• Follow the instructions that you find on
packaging of the detergents or other treatments
without exceeding the indicated maximum level
•
).
(
Use the recommended detergents for the type
and colour of the fabric, the programme
temperature and the level of soil.
•
•
•
Always start a washing programme with the
maximum load of laundry allowed.
If you pre-treat the stains or use a stain remover,
set a programme with a low temperature.
To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To find out the water hardness in your area, contact
your local water authority.
Use the correct quantity of water softener. Follow
the instructions that you find on the packaging of
the product.
ECOLOGICAL HINTS
• Set a programme without the prewash phase to
wash laundry with normal soil.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance with mild soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
CAUTION! Do not clean the metal
surfaces with chlorine-based
detergent.
Always follow the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
The repeated and prolonged use of low
temperature programmes can cause detergent
deposits, fluff residues, bacterial growth inside the
drum and the tub. This could generate bad odours
and mildew. To eliminate these deposits and clean
the inner part of the appliance, run a maintenance
wash regularly (at least once a month).
Refer to "Cleaning the drum"
paragraph.
DESCALING
If the water hardness in your area is
high or moderate, we recommend that
you use a water descaling product for
washing machines.
Regularly examine the drum to check for limescale.
Regular detergents already contain water softening
agents, but we recommend to run a cycle with an
empty drum and a descaling product occasionally.
27
DOOR SEAL
1. Open the drawer. Press the catch downwards
as indicated in the picture and pull it out.
Regularly examine the seal and remove all objects
from the inner part.
CLEANING THE DRUM
Regularly examine the drum to prevent unwanted
deposits.
Rust deposits in the drum may occur due to rusting
foreign body in the washing or tap water containing
iron
Clean the drum with special products for stainless
steel.
2. Remove the top part of the additive
compartment to aid cleaning and flush it out
under running warm water, to remove any
traces of accumulated detergent. After
cleaning, put the top part back into position.
Always follow the instructions that you
find on the packaging of the product.
Do not clean the drum with acidic
descaling products, scouring products
containing chlorine or iron or steel
wool.
For a thorough clean:
1. Remove all laundry from the drum.
2. Run the Machine Clean programme. For more
details, refer to washing programme table.
3. Add a small quantity of powder detergent into
the empty drum, in order to rinse out any left
residues.
3. Make sure that all detergent residue is removed
from the upper and lower part of the recess.
Use a small brush to clean the recess.
CLEANING THE DETERGENT DISPENSER
To prevent possible deposits of dried detergent or
clotted fabric softener and/or formation of mould in
the detergent dispenser drawer, once in a while
carry out the following cleaning procedure:
4. Insert the detergent drawer into the guide rails
and close it. Run the rinsing programme
28
without any clothes in the drum.
Regularly check the drain pump filter
and make sure that it is clean.
Clean the drain pump if:
• The appliance does not drain the water.
• The drum does not turn.
• The appliance makes an unusual noise because
of the blockage of the drain pump.
•
CLEANING THE DRAIN PUMP
WARNING! Disconnect the mains
plug from the mains socket.
The display shows the alarm code
.
WARNING!
• Do not remove the filter while the
appliance operates.
• Do not clean the pump if the water
in the appliance is hot. Wait until
the water cools down
Proceed as follows to clean the pump:
2
1. Open the pump cover.
1
2. Place a suitable bowl below the drain pump access
to collect the water that flows out.
Always keep a rag nearby to dry up any water spillages when removing the filter.
29
180˚
3. Turn the filter 180 degrees in anti-clockwise direction to open it, without removing. Let the water flow
out.
4. When the bowl is full of water, turn the filter back
and empty the container.
5. Repeat the steps 3 and 4 until the water stops to
flow out.
1
6. Turn the filter anti-clockwise to remove it
2
7. If it is necessary, remove fluff and objects from the
filter recess.
Make sure that the impeller of the pump can rotate. If it
does not rotate, contact the Authorised Service Centre.
8. Clean the filter under the water tap.
30
2
9. Put the filter back into the special guides by turning
it clockwise. Make sure that you tighten the filter correctly to prevent leakages.
1
2
10. Close the pump cover.
1
When you drain the water with the emergency drain procedure, you must activate the drain system again:
1. Put 2 litres of water in the main wash compartment of the detergent dispenser.
2. Start the programme to drain the water.
CLEANING THE INLET HOSE AND THE VALVE FILTER
1
2
3
45°
20°
31
EMERGENCY DRAIN
If the appliance cannot drain the water, carry out
the same procedure, described in 'Cleaning the
drain pump' paragraph. If necessary, clean the
pump.
When you drain the water with the emergency drain
procedure, you must activate the drain system
again:
1. Put 2 litres of water in the main wash
compartment of the detergent dispenser.
2. Start the programme to drain the water.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of the
hose.
4. Empty the drain pump. Refer to the emergency
drain procedure.
5. When the drain pump is empty, install the inlet
hose again.
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can reach values around 0° C or drop
below, remove the remaining water from the inlet
hose and the drain pump.
WARNING! Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during operation.
First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised
Service Centre.
WARNING! Deactivate the appliance before carrying out any check.
In case of major problems, the acoustic signals operate, the display shows an alarm code and
the Start/Pause
•
•
•
button may flash continuously:
- The mains supply is unstable. Wait until the mains supply is stable.
- No communication between electronic elements of the appliance. Switch it off and switch on
again. The programme was not finished properly or the appliance stopped too early. If the alarm code
appears again, contact the Authorised Service Centre.
- The appliance does not fill with water properly. After the proper check, start the appliance
again by pressing Start/Pause
button the appliance tries to resume the cycle . If the error persists
the alarm code will appear again.
•
- The appliance does not drain the water.
•
- The appliance door is open or not closed correctly. Please check the door!
If the appliance is overloaded, remove some items from the drum and/or hold the door shut
while touching the Start/Pause
picture below).
32
button until the indicator
stops flashing (see the
POSSIBLE FAILURES
Problem
The programme does not
start.
Possible solution
•
•
•
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is no damaged fuse in the fuse box.
•
•
Make sure that the Start/Pause
has been touched.
If the delay start is set, cancel the setting or wait for the end of
countdown.
Deactivate the Child Lock function if it is on.
Check the position of the knob on the selected programme.
•
•
•
•
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the inlet hose has no kinks, damages or bends.
Make sure that the connection of the water inlet hose is correct.
Make sure that the filter of the inlet hose and the filter of the valve
are not clogged. Refer to 'Care and cleaning'.
The appliance does not fill
with water properly.
•
•
•
•
The appliance fills with water and drains immediately.
•
Make sure that the drain hose is in the correct position. The hose
may be positioned too low. Refer to "Installation instruction".
•
•
•
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".
Make sure that the connection of the drain hose is correct.
Set the drain programme if you set a programme without drain
phase.
Set the drain programme if you set an option which ends with water
in the tub.
The appliance does not
drain the water.
•
•
•
The spin phase does not
operate or the washing cycle lasts longer than usual.
•
•
•
Set the spin programme.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
33
Problem
Possible solution
•
There is water on the floor.
•
•
•
You cannot open the appliance door.
•
•
•
•
•
The appliance makes an
unusual noise and vibrates.
•
•
The programme duration
increases or decreases
during programme execution.
Make sure that the couplings of the water hoses are tight and there
is not water leakages.
Make sure that the water inlet hose and the drain hose have no
damages.
Make sure you use the correct detergent and the correct quantity of
it.
Make sure that a washing programme that ends with water in tub,
has been selected.
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
Make sure that the appliance receives electrical power.
This problem may be caused by a failure of the appliance. Contact
the Authorised Service Centre.
If you need to open the door, please read carefully "Emergency
door opening".
Make sure the levelling of the appliance is correct. Refer to "Installation instruction".
Make sure that the packaging and/or the transit bolts are removed.
Refer to "Installation instruction".
Add more laundry in the drum. The load may be too small.
•
The AutoAdjust System is able to adjust the programme duration
according to the type and the laundry load size. Refer to "The AutoAdjust System load detection" in "Daily Use" chapter.
•
•
•
•
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
Too much foam in the
drum during the washing
cycle.
•
Reduce the quantity of detergent.
After the washing cycle,
there are some detergent
residues in the dispenser
drawer.
•
Make sure that the flap is in the correct position (UP for powder
detergent - DOWN for liquid detergent).
Make sure you have used the detergent dispenser according the
indications given in this user manual.
The washing results are
not satisfactory.
•
After the check, activate the appliance. The programme continues from the point of interruption.
If the problem occurs again, contact the Authorised Service Centre.
If the display shows other alarm codes, deactivate and activate the appliance. If the problem continues,
contact the Authorised Service Centre.
EMERGENCY DOOR OPENING
In case of power failure or functioning failure the
appliance door remains locked. The washing
programme continues when the power is restored.
If the door remains locked in case of failure, it is
possible to open it using the emergency unlock
function.
34
Before opening the door:
CAUTION! Risk of burns! Make
sure that the water temperature is
not too high and the laundry is
not hot. If necessary, wait until
they cool down.
the meanwhile, open the appliance door. The
emergency unlock trigger is located where
indicated by the following picture.
CAUTION! Risk of injury! Make
sure that the drum is not rotating.
If necessary, wait until the drum
stops rotating.
Make sure that the water level
inside the drum is not too high. If
necessary, proceed with an
emergency drain (refer to
«Emergency drain» in «Care and
cleaning» chapter).
To open the door, proceed as follows:
1. Press the On/Off button to switch the
appliance off.
2. Disconnect the mains plug from the mains
socket.
3. Pull the emergency unlock trigger downward
once. Pull it once again, keep it tensed and, in
4. Take out the laundry and then close the
appliance door.
TECHNICAL DATA
Dimension
Width/ Height/ Depth/ Total depth
596 mm/ 819 mm/ 540 mm/ 553 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
230-240 V
2200 W
13 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
1)
Minimum
Maximum
Cold water
Water supply 2)
Maximum Load
Cotton
Energy Efficiency Class
Spin Speed
7 kg
A+++
Maximum spin speed
1151 rpm
1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.
2) Connect the water inlet hose to a water tap with a 3/4'' thread.
35
PRODUCT INFORMATION SHEET IN REFERENCE TO E.U. REGULATION
1369/2017
Product Information Sheet
Trade Mark
Model
Rated capacity in kg
7
Energy efficiency class
A+++
Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and
partial load, and the consumption of the low-power modes. Actual
energy consumption will depend on how the appliance is used.
174.0
Energy consumption of the standard 60°C cotton programme at full
load in kWh
0.93
Energy consumption of the standard 60°C cotton programme at partial load in kWh
0.70
Energy consumption of the standard 40°C cotton programme at partial load kWh
0.55
Power consumption of the off-mode in W
0.48
Power consumption in left-on mode in W
0.48
Water consumption in litres per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and
partial load. Actual water consumption will depend on how the appliance is used.
Spin-drying efficiency class on a scale from G (least efficient) to A
(most efficient)
Maximum spin speed in rpm
Remaining moisture content in %
36
ZANUSSI
Z712W43BI,
PNC914580201
10499
B
1151
53
The 'standard 60 °C cotton programme' and the 'standard 40 °C
cotton programme' are the standard washing programmes to which
the information in the label and the fiche relates, these programmes
are suitable to clean normally soiled cotton laundry and they are the
most efficient in terms of combined energy and water consumption.
-
Programme time of the standard 60°C cotton programme at full load
in minutes
250
Programme time of the standard 60°C cotton programme at partial
load in minutes
205
Programme time of the "standard 40°C cotton programme at partial
load in minutes
200
Duration of the left on mode in minutes
5
Airborne acoustical noise emission in db(A) washing
54
Airborne acoustical noise emission in db(A) spinning
70
Built in appliance Y/N
Yes
The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC .
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
37
*
38
39
157018374-C-352019
WWW.ZANUSSI.COM/SHOP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement