ZANUSSI ZWC1301 User Manual
User Manual
GETTING
STARTED?
EASY.
ZWC 1301
EN User Manual
Washing Machine
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
2
Do not change the specification of this appliance.
This appliance is intended to be used in household and similar
applications such as:
– staff kitchen areas in shops, offices and other working
environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments;
– areas for communal use in blocks of flats or in launderettes.
•
•
•
•
•
•
•
•
•
Do not exceed the maximum load of 3 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
•
•
•
•
•
•
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Follow the installation instructions supplied with
the appliance.
Do not install or use a damaged appliance.
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
•
•
•
•
•
•
•
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
Make sure that there is air circulation between
the appliance and the floor.
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
Do not install the appliance directly above a
floor drain.
Do not spray water on the appliance and do not
expose it to excessive humidity.
Do not install the appliance where the appliance
door cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the appliance.
Contact the Authorised Service Centre to
ensure which accessories can be used.
3
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
•
•
•
•
•
•
•
•
•
•
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
• Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
• When unpacking the appliance, It is possible to
see water flowing from the drain hose. This is
due to the testing of the appliance with the use
of water in the factory.
•
•
You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
Make sure that there is access to the tap after
the installation.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
•
•
•
•
•
Follow the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Make sure that all metal objects are removed
from the laundry.
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Do not touch the glass door while a programme
is in operation. The glass can get hot.
SERVICE
• To repair the appliance contact the Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
•
•
•
•
Disconnect the appliance from the mains
electrical and water supplies.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the drum.
Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
INSTALLATION
WARNING! Refer to Safety chapters.
4
UNPACKING
When supplied the washing machine is packed
using a number of locking devices/packing pieces
to prevent drum and motor from damage in transit
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Spread some of the polystyrene packaging
materials on the floor behind the machine and
then lay the machine carefully rear side down
on them. Make sure that no hoses are crushed
in the process.
5. The three holes must then be plugged with the
plastic plug caps supplied in the bag
containing the instruction booklet, which can
be found inside the drum.
2. Remove the polystyrene base from the bottom
of the appliance.
LIFTING THE MACHINE
Be careful when lifting the machine. Incorrect
methods of lifting can cause physical injuries and
also increase the risk of damage to the machine.
Open the door and take hold of the top inside of
the door opening. You can also lift the machine by
gripping the rear overhang of the top.
3. Return machine to it's upright position and
remove the power supply cable and the
draining and inlet hose from the hose holders
on the rear of the appliance.
4. With a suitable spanner unscrew and remove
the three screws and their spacers on
machine's rear.
WARNING! Never lift the machine by
gripping it’s control panel, door, or
detergent dispenser.
5
POSITIONING
Install the machine on a flat hard floor. Make sure
that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the
machine does not touch the wall or furniture. Level
the washing machine by raising or lowering the two
front feet. If necessary, check the setting with a
spirit level. Any necessary adjustment can be made
with a spanner. Accurate levelling prevents
vibration, noise and displacement of the machine
during operation.
inlet hose, be sure to tighten the ring nut again
to prevent leaks.
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
Before connecting up the machine to
new pipework or to pipework that has
not been used for some time, run off a
reasonable amount of water to flush
out any debris that may have collected
in the pipes.
CAUTION! Never place cardboard,
wood or similar materials under the
machine to compensate for any
unevenness in the floor.
WATER INLET
WATER DRAINAGE
The end of the drain hose can be positioned in
three ways:
Hooked over the edge of a sink using the
plastic hose guide supplied with the
machine.
WARNING! This appliance must
be connected to a cold water
supply.
1. Connect the water inlet hose supplied with the
machine to a tap with a 3/4" thread. Always
use the hose supplied with the appliance.
In this case, make sure the end cannot come
unhooked when the machine is emptying. This
could be done by tying it to the tap with a piece of
string or attaching it to the wall.
Do not use the hose from your
previous machine to connect
to the water supply.
2. The machine end of the inlet hose can be
turned in any direction. Set the hose correctly
by loosening the ring nut. After positioning the
6
In a sink drain pipe with a trap.
There must be an air gap around and below the
end of drain hose. This means that the internal
diameter of the standpipe must be larger than the
outer diameter of the hose.
The hose must not be sticked into the standpipe
more than 50 mm and it has to be fixed in this
position. The drain hose must not be kinked.
The drain hose can be extended up to total 3,5 m.
For the extension piece use a hose with an internal
diameter at least as large as that of the machine's
own hose. Use a suitable hose connector.
650-800 mm
The drain hose can be connected directly into the
pipe (e.g. beneath a washtub or sink), above the
water trap. The drain hose must be arranged so
that some part of it’s length is routed up to a level
corresponding to the top edge of the tub and fixed
in place there.
Directly into a drain pipe at a height of not less
than 65 cm and not more than 80 cm.
ø40 mm
650-800 mm
INSTALLATION ON SUSPENDED FLOORING
Suspended wooden floors are particularly
susceptible to vibration.
To limit vibration we recommend placing a
waterproof wooden panel, at least 15 mm thick,
under the appliance. It should be screwed to at
least 2 floor beams and should extend beyond the
front feet.
If possible, install the appliance where the floor is
more stable.
7
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
6
7
3
8
4
9
5
1 Detergent dispenser drawer
2 Control panel
6 Drain hose
7 Inlet hose
3 Door handle
4 Rating plate
8 Transit bolts
9 Mains cable
5 Feet for levelling the appliance
CONTROL PANEL
CONTROL PANEL DESCRIPTION
1
2
3
Spin
Spin
Cottons
90°
1300
Quick
Drain
8h
Daily
Time
Prewash
Extra
Rinse
Start
Pause
Delay
Start
900
4h
60°
Rinses
2h
Washing
Mini 30
End
700
Door
Wool
Cold
500
30°
Wool 40°
Specials
40°
Mix 20°
Delicate 40°
30°
Synthetics
9 8 7 6 5 4
1 Detergent drawer
2 SPIN reduction selector
8
3 Programme selector dial
4 Programme progress indicators
5 DELAY START button
6 START/PAUSE button
7 EXTRA RINSE button
8 PREWASH button
9 TIME saving button
TIME SAVING BUTTON
By means of this button, you can select only one of
the options. You must select option after you have
set the programme and before you press button
Start/Pause. The relevant light will illuminate.
• Daily
Short programme for lightly soiled white-/
coloured and synthetic laundry. The washing
time will be reduced approx. 10 minutes. Max.
recommended temperature 60°C.
• Quick
Short programme for normally soiled cotton,
synthetic or delicate items. The washing time
will be reduced according to the type of fabric
and the selected temperature.
DELAY START
The start of the programme can be delayed by 8, 4
or 2 hours by means of this button. The selected
delay is indicated by the illumination of the
corresponding light.
This options can not be chosen
together with the programme 60E
and neither with the wool, delicate
or hand wash programmes. The
washing time will be reduced
depending on the type of material
and the selected temperature.
Recommended load for cotton is 2
kg.
PREWASH
By selecting this option the machine performs a
prewash cycle before the main wash phase. The
washing time will be prolonged. This option is
recommended for heavily soiled laundry.
EXTRA RINSE
With this option you can add some rinses to a
washing programme. If it necessary to rinse the
laundry using an extra quantity of water (extra
rinse), select this option. Some additional rinses will
be performed. This option is recommended for
people who are allergic to detergents, and in areas
where the water is very soft.
START/PAUSE
This button allows you to start or to interrupt the
selected programme.
INDICATORS
A
4h
B
2h
C
Washing
D
End
E
Door
The light A illuminates when the Delay Start is
selected, start of the washing programme will
be delayed for 4 hours.
The light B illuminates when the Delay Start is
selected, start of the washing programme will
be delayed for 2 hours.
The light C illuminates when the machine is
performing the washing phase.
The light D illuminates at the end of the washing
cycle.
The light E indicates if the door can be opened:
• The light is on: the door cannot be opened.
• The light is off: the door can be opened.
• The light is flashing: the door can soon be
opened.
SPIN REDUCTION DIAL
By turning the spin speed selector you can change
the spin speed of the selected programme or to
select Rinse Hold
or No Spin
option.
PROGRAMME SELECTOR DIAL
It allows you to switch the appliance on/off and/or
to select a programme.
9
WASHING PROGRAMMES
Programme/
Temperature
Type of laundry
Available options
Description of the
programme
COTTONS
90°-60°-30°C
White cotton (heavily
and normally soiled cotton items)
SPIN REDUCTION/NO
SPIN/RINSE HOLD
DELAY START
PREWASH
DAILY/QUICK1)
EXTRA RINSE
Main wash
Rinses
Reference spin
speed
1300 rpm
Max load 3 kg
COTTONS ECO
White cotton eco
(This programme can be
selected for slightly or
normally soiled cotton
items. The temperature
will decrease and the
washing time will be extended. This allows to obtain a good washing efficiency so saving energy.)
SPIN REDUCTION/NO
SPIN/RINSE HOLD
DELAY START
PREWASH
EXTRA RINSE
Main wash
Rinses
Reference spin
speed
1300 rpm
Max load 3 kg
Synthetic or mixed
fabrics: underwear, coloured garments, nonshrink shirts, blouses.
SPIN REDUCTION/NO
SPIN/RINSE HOLD
DELAY START
PREWASH
DAILY/QUICK
Main wash
Rinses
Reference spin
speed
900 rpm
Max Load 1,5 kg
2)
60°-40°C
SYNTHETIC
40° - 30°C
1)
EXTRA RINSE
DELICATE
40°C
Delicate fabrics: acrylics, viscose, polyester.
SPIN REDUCTION/NO
SPIN/RINSE HOLD
DELAY START
PREWASH
QUICK
EXTRA RINSE
Main wash
Rinses
Reference spin
speed
700 rpm
Max Load 1,5 kg
MIX 20°
20°C
Very energy efficient cold
wash programme. Light
soil. This programme requires a detergent which
is active in cold water.
SPIN REDUCTION/NO
SPIN/RINSE HOLD
DELAY START
EXTRA RINSE
Main wash
Rinses
Reference spin
speed
900 rpm
Max Load 1,5 kg
WOOL
40°C - COLD
Washing programme for
machine washable wool.
SPIN REDUCTION/NO
SPIN/RINSE HOLD
DELAY START
Main wash
Rinses
Reference spin
speed
900 rpm
Max Load 1 kg
(
10
)
Programme/
Temperature
Type of laundry
Available options
Description of the
programme
MINI 30
30°C
For lightly soiled laundry
or for laundry which
needs freshening up.
SPIN REDUCTION/NO
SPIN/RINSE HOLD
DELAY START
Main wash
Rinses
Reference spin
speed
700 rpm
Max Load 1,5 kg
RINSES
With this programme it is
possible to rinse and spin
cotton garments which
have been washed by
hand. The machine performs 3 rinses, followed
by a final long spin. The
spin speed can be reduced.
SPIN REDUCTION/NO
SPIN/RINSE HOLD
DELAY START
EXTRA RINSE
Rinses
Reference spin
speed
1300 rpm
Max Load 3 kg
DRAIN
For emptying out the water of the last rinse in programmes with the Rinse
Hold option selected.
SPIN
Separate spin for hand
washed garments and after programmes with the
Rinse Hold option selected. You can choose the
spin speed by turning the
spin speed selector to
adapt it to the fabrics to
be spun.
/OFF
Draining of water
Max Load 3 kg
SPIN REDUCTION
Drain and long spin
Reference spin
speed
1300 rpm
Max Load 3 kg
For resetting the programme or switching the machine off
1) If you select this option, we recommend that you reduce the maximum load. Recommended load for cotton is 2 kg.
2) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, these programmes are respectively the «Standard 60 °C cotton programme» and the «Standard 40 °C cotton programme». They are the most efficient programmes in terms of combined energy and
water consumptions for washing normally soiled cotton laundry.
BEFORE FIRST USE
1. Make sure that all transit bolts have been
removed from the appliance.
2. Connect the mains plug to the mains socket.
3. Open the water tap.
4. Pour approx. 100 ml of detergent straight into
the drum.
5. Set and start a programme for cotton at the
highest temperature without laundry. This
removes all posssible dirt from the drum and
the tub.
11
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
1. Open the appliance door
2. Shake the items before you put them in the
appliance.
3. Put the laundry in the drum, one item at a time.
Make sure not to put too much laundry in the drum.
4. Close the door firmly.
Compartment for powder or liquid detergent
used for main wash. If using liquid detergent,
pour it just before starting the programme.
When you set a programme
with prewash, put the detergent
for prewashing phase directly
into the drum.
Compartment for liquid additives (fabric softener, starch).
Any fabric softener or starching additives
must be poured into the compartment before
starting the wash programme.
MEASURE OUT THE DETERGENT AND THE
FABRIC SOFTENER
Make sure that no laundry gets caught
between the seal and the door to
avoid risk of water leakage and
damage to the laundry.
Washing heavily oiled, greasy stains
could cause damage rubber parts of
the washing machine.
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required,
pour it into the larger compartment on the left
.
DETERGENT DISPENSER DRAWER
Detergent drawer has 2 separate compartments for
detergent and fabric conditioner.
If required, pour fabric softener into the smaller
compartment marked
(the amount used must
not exceed the «MAX» mark in the drawer). Close
the drawer gently.
12
SELECT THE DESIRED OPTIONS
Depending on the programme, different functions
can be combined. These must be selected after
choosing the desired programme and before
pressing the button Start/Pause. The relevant light
will illuminate.
If an incorrect option is selected, the corresponding
indicator lamp flashes for about 2 seconds. For the
compatibility of the options with the washing
programmes, refer to the chapter 'Washing
programmes'.
SELECT THE SPIN SPEED, RINSE HOLD OR
NO SPIN OPTION
Select the spin speed, Rinse Hold option or No
Spin option by turning the spin speed selector.
• The position 1300 is equivalent to 800 rpm for
the Synthetic and Wool programmes and 700
rpm for the Delicate wash programme.
Rinse hold
By selecting this option the water of the last rinse is
not emptied out to prevent the fabrics from
creasing. When the programme has finished, the
lights D and E are lit to indicate that the water must
be emptied out (See: 'At the end of the
programme').
No spin
By selecting this option all the spinning phases are
excluded. To be used for extremely delicate
material. The machine will add some additional
rinses to the cotton and synthetic programmes.
For the maximum spin speed allowed by each
programme, refer to the chapter 'Washing
programmes'.
SELECT THE DELAY START
Before you start the programme, if you wish to
delay the start, press the button Delay Start
repeatedly, to select the desired delay. The light
corresponding to the set delay lights up.
8h
Delay
Start
4h
2h
You must select this option after you have set the
programme and before you press button Start/
Pause.
You can cancel or modify the delay time at any
moment, before you press button Start/Pause.
Cancelling the delayed start after having pressed
button Start/Pause:
1. Set the washing machine to PAUSE by
pressing button Start/Pause.
2. Press the button Delay Start once, the light
relevant to the selected delay goes off.
3. Press button Start/Pause again to start the
programme.
The selected delay can be changed
only after selecting the washing
programme again.
The door will be locked throughout the
delay time (door locked light lit).
The Delay Start can not be selected
with Drain or Spin programme.
SELECT THE REQUIRED PROGRAMME BY
MEANS OF THE PROGRAMME SELECTOR
DIAL
Turn the programme selector dial to the required
programme. The selector can be turned either
clockwise or anticlockwise.
The green light of button Start/Pause starts to flash.
The pilot lights corresponding to all phases
composing the selected programme are on.
On position
the programme is reset and the
machine is switched OFF.
At the end of the programme the selector dial must
be turned to position
to switch the machine off.
If you turn the programme selector dial
to another programme when the
machine is working, the lights in the
programme progress display will start
to flash to indicate a wrong selection.
The machine will not perform the new
selected programme.
STARTING THE PROGRAMME
To start the selected programme, press the button
Start/Pause; the corresponding pilot light stops
flashing and remains on.
On programme progress display the pilot lights C
and E illuminate to indicate that the appliance starts
operating and the door is locked.
13
ALTERING AN OPTION OR A RUNNING
PROGRAMME
It is possible to change any option before the
programme carries it out.
Before you make any change, you must pause the
washing machine by pressing the button Start/
Pause.
The programme can be changed as long as the
button Start/Pause has not been pressed.
Changing a running programme is possible only by
resetting it. Turn the programme selector dial to
and then to the new programme position. Start the
new programme by pressing the button Start/
Pause again.
INTERRUPTING A PROGRAMME
Press the button Start/Pause to interrupt a
programme which is running, the corresponding
light starts to flash. Press the button again to restart
the programme.
CANCELLING A PROGRAMME
Turn the selector dial to
position to cancel a
programme which is running. Now you can select a
new programme.
OPENING THE DOOR AFTER THE
PROGRAMME HAS STARTED
First set the machine to pause by pressing the
button Start/Pause.
After some minutes, the door can be opened, when
the following conditions are observed:
• The water temperature is below 55°C.
• The water level is below the bottom edge of the
door.
• The machine doesn’t spin.
If you cannot open the door but it is absolutely
necessary to open it you have to switch the
machine off by turning the selector dial to
. After
few minutes the door can be opened. (Pay
attention to the water level and
temperature!).
After this procedure, it will be necessary to set the
programme and the options again and then press
the button Start/Pause.
AT THE END OF THE PROGRAMME
The machine stops automatically.
The pilot light D illuminates to indicate that the
programme has finished. The pilot light E goes out,
the door can be opened and the laundry can be
removed.
If at the end of a programme there is water in the
tub (when
option has been selected), to
empty out the water follow the following
instructions:
• turn the programme selector dial to
• select the Drain or Spin programme,
• press button Start/Pause.
When the pilot light E goes out, the door can be
opened and the laundry can be removed.
At the end of the cycle, turn the programme
selector dial to
to switch the machine off.
Remove the laundry from the drum and carefully
check that the drum is empty. If you do not intend
to carry out another wash, close the water tap.
Leave the door open to prevent the formation of
mildew and unpleasant smells.
HINTS AND TIPS
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on the
laundry care labels.
• Do not wash white and coloured items together.
• Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
• Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn multilayered fabrics, wool and items with
painted illustrations inside out.
• Remove hard stains with a special detergent.
14
•
•
•
•
Wash and pre-treat heavy soil stains before
putting items in drum
Be careful with the curtains. Remove the hooks
and put the curtains in a washing bag or
pillowcase.
Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (40
°C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
•
If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
• Set a programme without the prewash phase to
wash laundry with normal soil.
• Always start a washing programme with the
maximum load of laundry allowed.
• If necessary, use a stain remover when you set a
programme with a low temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance with soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
Always obey the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
• Remove all laundry from the drum.
• Select the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
Regularly examine the seal and remove all objects
from the inner part.
CLEANING THE DISPENSER DRAWER
The washing powder and additive dispenser drawer
should be cleaned regularly.
15
1. If necessary, the whole detergent drawer can
be taken out of the machine for cleaning. You
need to pull it firmly outwards, so that it comes
free of retaining stop.
2. To remove the siphon at the inside edge of the
drawer for cleaning, you need to press it
inwards and pull it upwards at the same time.
Flush it out under a tap, to remove any traces of
accumulated powder. When you put it back,
press it downwards until you hear a distinct
click.
CLEANING THE DRAWER RECESS
Having removed the drawer, use a small brush to
clean the recess, ensuring that all washing powder
residue is removed from the upper and lower part
of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
CLEANING THE INLET HOSE AND THE VALVE FILTER
1.
2.
1
2
3
16
3.
4.
45°
20°
THE DANGERS OF FREEZING
If the machine is exposed to temperatures below
0°C, certain precautions should be taken.
• Turn off the water supply.
• Unscrew the inlet hose from the supply tap.
• Select a wash programme, start the machine
and let the programme run for a short time.
• Interrupt the programme by turning the
•
programme selector to
position.
Place the end of inlet and drain hoses down
low, into the waste gully (floor drain) set into the
floor. Make sure that the end of the hose does
not go below the water level in the gully's
(drain's) water tap.
•
Select the programme "Drain" and let it run until
it is finished.
•
Turn the programme selector to
position.
When you intend to start the machine up again,
make sure that the room temperature is above 0
°C.
The appliance is only to be used and stored
indoors at normal room temperature. The
manufacturer is not responsible for any frost
damage.
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
Programmes
Cottons 60°C
Cottons 40°C
Load (kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
Remaining
programme
duration (mi- moisture (%)1)
nutes)
3
0,90
45
120
52
3
0,45
45
110
52
Synthetics 40°C
1,5
0,50
50
80
35
Delicates 40°C
1,5
0,50
52
70
35
17
Programmes
Load (kg)
1
Wool plus 30°C 2)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
Remaining
programme
duration (mi- moisture (%)1)
nutes)
0,30
60
75
30
3
0,59
42
127
52
1,5
0,54
38
127
52
1,5
0,49
38
137
52
Standard cotton programmes
Standard 60°C cotton
Standard 60°C cotton
Standard 40°C cotton
1) At the end of spin phase.
2) Not available for some models.
Off Mode (W)
0.10
Left On Mode (W)
0.98
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC .
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
Certain problems are due to lack of simple
maintenance or oversights, which can be solved
easily without calling out an engineer. Before
contacting your Authorised Service Centre, please
carry out the checks listed below.
18
During machine operation it is possible that the
End pilot light blinks to indicate that the machine is
not working:
• 1 flash: problem with the water supply.
• 2 flashes: problem with the water draining.
• 4 flashes: door open.
Once the problem has been eliminated, press the
button START to restart the programme. If after all
checks, the problem persists, contact your
Authorised Service Centre.
POSSIBLE FAILURES
Problem
Possible cause/Solution
The machine does not
start:
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the button Start
has not been pressed.
• Please turn the selector dial and press the button Start again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay
start.
The machine does not fill:
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose is blocked.
• Clean the water inlet hose filter.
The door is not properly closed.
• Close the door firmly.
The machine fills then
empties immediately:
The end of the drain hose is too low.
• Refer to relevant paragraph in «Installation» chapter.
The machine does not
empty and/or does not
spin:
The drain hose is squashed or kinked.
• Check the drain hose connection.
An option or a programme that ends with the water still in the tub or
that eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the
floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not always easy to see this as the water runs down the
hose; check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Change it with a new one.
Unsatisfactory washing results:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
19
Problem
Possible cause/Solution
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the indicator light for door locked has gone out.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed
in the drum, the machine will not spin. In this case ,redistribute the
load manually and select the spin programme.
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select
the spinning programme.
No water is visible in the
drum:
Machines based on modern technology operate very economically
using very little water without affecting performance.
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Authorised
Service Centre.
TECHNICAL DATA
Dimension
Width/ Height/ Depth/ Total depth
495 mm/ 670 mm/ 515 mm/ 550 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
230-240 V
1600 W
13 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
1)
Water supply 2)
20
Minimum
Maximum
Cold water
Maximum Load
Cotton
3 kg
Energy Efficiency Class
Spin Speed
A
Maximum spin speed
1251 rpm
1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.
2) Connect the water inlet hose to a water tap with a 3/4'' thread.
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
21
*
22
23
192987444-A-012019
WWW.ZANUSSI.COM/SHOP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement