advertisement

Zoppas PWF6082WEX User Manual
User Manual
GETTING
STARTED?
EASY.
EN User Manual
Washing Machine
PWF6082WEX
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
•
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
If the appliance has a child safety device, it should be activated.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
2
Do not change the specification of this appliance.
This appliance is intended to be used in household and similar
applications such as:
– staff kitchen areas in shops, offices and other working
environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments;
•
•
•
•
•
•
•
•
•
– areas for communal use in blocks of flats or in launderettes.
Do not exceed the maximum load of 6 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
•
•
•
•
•
•
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Follow the installation instructions supplied with
the appliance.
Do not install or use a damaged appliance.
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
•
•
•
•
•
•
•
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
Make sure that there is air circulation between
the appliance and the floor.
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
Do not install the appliance directly above a
floor drain.
Do not spray water on the appliance and do not
expose it to excessive humidity.
Do not install the appliance where the appliance
door cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the appliance.
Contact the Authorised Service Centre to
ensure which accessories can be used.
3
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
•
•
•
•
•
•
•
•
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
• Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
• When unpacking the appliance, It is possible to
see water flowing from the drain hose. This is
due to the testing of the appliance with the use
of water in the factory.
• You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
4
•
Make sure that there is access to the tap after
the installation.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
•
•
•
•
•
Follow the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Do not touch the glass door while a programme
operates. The glass can get hot.
Make sure that all metal objects are removed
from the laundry.
SERVICE
• To repair the appliance contact the Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
•
•
•
•
Disconnect the appliance from the mains
electrical and water supplies.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the drum.
Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
3
4
5
6
7
1 Worktop
2 Detergent dispenser
5 Rating plate
6 Drain pump filter
3 Control panel
4 Door handle
7 Feet for levelling the appliance
CHILD SAFETY DEVICE
This device prevents children or pets to be closed in the drum.
Turn the device clockwise, until the groove is horizontal. You cannot
close the door.
To close the door, turn the device anticlockwise until the groove is vertical.
5
CONTROL PANEL
CONTROL PANEL DESCRIPTION
1
2 3
1 Programme knob
2 Temperature touchpad
(Temperatura)
3 Spin reduction touchpad
Including:
•
5
6
8
9 10
: The end of cycle indicator
•
: The child lock indicator
7 Extra rinse touchpad
•
: The Rinse Hold indicator
4 The Delay Start Indicator (Ritardo): You can
choose between 3hours, 6hours & 9hours
5 The Indicator Lights:
7
•
6 Prewash touchpad
(Centrifuga)
: The no spin indicator
•
4
8 Start/Pause touchpad
(Prelavaggio)
(Extra risciacquo)
(Avvio/Pausa)
9 Delay start touchpad
(Partenza posticipata)
10 Quick wash touchpad
(Lavaggio rapido)
: The door lock indicator
PROGRAMMES
PROGRAMME CHART
Programme
Temperature range
Cotoni
90°C -
(Cold)
Cotoni Eco
60°C - 40°C
Sintetici
60°C -
6
(Cold)
1)
Maximum load
Reference
spin speed
Programme description
(Type of load and soil level)
6 kg
800 rpm
White cotton and coloured cotton. Normal soil and
light soil.
6 kg
800 rpm
White cotton and colour-fast cotton. Normal soil. The
energy consumption decreases and the time of the washing programme is extended.
3 kg
800 rpm
Synthetic items or mixed fabric items. Normal soil.
Programme
Temperature range
Maximum load
Reference
spin speed
Programme description
(Type of load and soil level)
3 kg
800 rpm
Delicate fabrics such as acrylics, viscose, polyester
items. Normal soil.
2 kg
800 rpm
Machine washable wool, hand washable wool and
delicate fabrics with «hand washing» care symbol.2)
6 kg
800 rpm
Special programme for cotton or mixed dark-colored
laundry. The program optimises the rinse phase, removing any detergent residual to preserve your bright colors.
Liquid or wool detergent is recommended for dark laundry.
4 kg
800 rpm
Special programme for cotton, synthetic and mixed fabrics
lightly soiled. Select this programme to reduce the energy
consumption. Make sure that the detergent is suitable for
low temperatures in order to have good washing results3).
Risciacquo 4)
6 kg
800 rpm
To rinse and spin the laundry. All fabrics, except woollens and very delicate fabrics. Reduce the spin speed accordingly to the type of laundry.
Scarico
8 kg
To drain the water in the drum. All fabrics.
Centrifuga
8 kg
800 rpm
The default phase of the spin speed is related to cotton
items. Set the spin speed. Make sure that it agrees with
the laundry.
4 kg
800 rpm
Synthetic items requiring a gentle wash. Normal and
light soil.5)
Quick 20
40°C - 30°C
3 kg
800 rpm
A very short cycle for cotton and synthetic items with
light soil level or worn only once.
Jeans
6 kg
800 rpm
Items in denim and jersey. Normal soil.
3 kg
800 rpm
A short cycle for synthetic and delicate items with
light soil level or for items to freshen up.
Delicati
40°C -
(Cold)
Lana/Lavaggio a
mano
40°C -
(Cold)
Scuri
60°C -
(Cold)
Mix 20°
20°C
Stiro Facile
60°C -
60°C 30'@30°
30°C
(Cold)
(Cold)
7
Programme
Temperature range
Maximum load
Reference
spin speed
Programme description
(Type of load and soil level)
To switch the appliance on or off and for cancelling the
programme which is running.
On/Off
1) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and
water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
3) The appliance performs the short heating phase if the water temperature is below 20°C. The appliance
can show the temperature setting as “cold”.
4) Press Extra Rinse button to add rinses. With a low spin speed the appliance performs delicate rinses.
and a short spin.
5) To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin
phase. The appliance adds some rinses.
Centrifuga
No Spin
Rinse Hold
Prelavaggio
Extra risciacquo
Lavaggio rapido
Partenza posticipata
Programme options compatibility
Cotoni
■
■
■
■
■
■
■
Cotoni Eco
■
■
■
■
■
Sintetici
■
■
■
■
■
Delicati
■
■
■
■
■
Lana/Lavaggio a mano
■
■
■
Scuri
■
■
■
Programme
8
■
■
■
■
■
■
■
■
Partenza posticipata
Lavaggio rapido
Rinse Hold
Extra risciacquo
No Spin
Prelavaggio
Centrifuga
Mix 20°
■
■
■
■
■
Risciacquo
■
■
■
■
■
Programme
■
Scarico
■
Centrifuga
■
■
Stiro Facile
■
Quick 20
■
■
Jeans
■
■
■
■
■
■
■
■
■
■
■
■
■
30'@30°
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Programmes
Load (kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
Remaining
programme
duration (mi- moisture (%)1)
nutes)
Cottons 60°C
6
1.5
70
180
66
Cottons 40°C
6
1
70
170
66
Synthetics 40°C
3
0.6
55
120
37
Delicates 40°C
3
0.55
60
100
37
9
Programmes
Load (kg)
Wool/Handwash
30°C
Energy consumption
(kWh)
2
2)
Water consumption (litre)
Approximate
Remaining
programme
duration (mi- moisture (%)1)
nutes)
0.3
60
75
37
Standard cotton programmes
Standard 60°C cotton
6
0.86
47
230
66
Standard 60°C cotton
3
0.56
36
190
66
Standard 40°C cotton
3
0.52
36
190
66
1) At the end of spin phase.
2) Not available for some models.
Left On Mode (W)
Off Mode (W)
0.48
0.48
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC .
OPTIONS
TEMPERATURA
Set this option to change the default temperature.
•
Indicator
•
= cold water.
CENTRIFUGA
With this option you can decrease the default spin
speed.
The related spin speed indicator comes on.
Additional spin options:
No Spin
• Set this option to remove all spin phases.
• Set it for very delicate fabrics.
• The rinse phase uses more water for some
washing programmes.
comes on.
• The related indicator
Rinse Hold
• Set this option to prevent the laundry creases.
10
•
The washing programme stops with the water in
the drum. The drum turns regularly to prevent
the laundry creases.
The door stays locked. You must drain the water
to unlock the door.
The rinse hold indicator
comes on.
To drain the water refer to ‘At the end
of the programme’.
PRELAVAGGIO
With this option you can add a prewash phase to a
washing programme.
Use this option for heavy soil.
When you set this option the programme duration
increases.
The related indicator comes on.
EXTRA RISCIACQUO
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related phase indicator on the control panel
comes on.
LAVAGGIO RAPIDO
With this option you can decrease the programme
duration.
Use this option for items with light soil or items to
refresh.
The related indicator comes on.
PARTENZA POSTICIPATA
With this option you can delay the start of the
programme.
The indicator light goes on for delaying: 3, 6 & 9
hours.
SETTINGS
ACOUSTIC SIGNALS
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
press Extra risciacquo
and Partenza posticipata
at the same time for 6 seconds.
If you deactivate the acoustic signals,
they continue operate when the
appliance has a malfunction.
•
To activate/deactivate this option, press
Prelavaggio
and Extra risciacquo
same time until the indicator
goes off.
You can activate this option:
at the
comes on/
•
After you press
: the options and the
programme knob are locked.
•
Before you press
start.
: the appliance cannot
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
BEFORE FIRST USE
1. Make sure that the electrical and water
connections comply with the installation
instructions.
2. Remove the polystyrene block and any material
from the drum.
3. Put a small quantity of detergent in the
compartment for washing phase.
4. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to maximum loads indicated in "Programme
chart".
4. Close the door.
11
USING DETERGENT AND ADDITIVES
CAUTION! Make sure that no laundry
stays between the seal and the door.
There is a risk of water leakage or
damage to the laundry.
Open the detergent
drawer .
Measure out the detergent.
Measure out the fabric
conditioner.
Carefully close the detergent drawer.
DETERGENT COMPARTMENTS
CAUTION! Use only specified detergents for washing machine.
Always obey the instructions that you
find on the packaging of the detergent
products.
BLEACH
Alternatively the softener, it is also possible to use a
bleach agent in the compartment
programmes for white cottons.
Proceed as follows:
Detergent compartment for prewash or soak
phase.
The prewash and soak detergent must be
added at the beginning of the wash programme.
Compartment for powder or liquid detergent
used for main wash. If using liquid detergent,
pour it just before starting the programme.
Compartment for liquid additives (fabric conditioner, starch).
Follow the product manufacturer’s recommendations on quantities to use and do not
exceed the maximum mark in the detergent
dispenser drawer.
12
with the
.
1. Put the bleach in the compartment
Do not exceed the «MAX» mark in the detergent
dispenser drawer.
2. Run a programme for white cottons.
3. At the end of the programme, run the
programme RINSE. Use softener, if desired.
This helps to eliminate any bleach residues.
Never pour bleach and softener into
the compartment at the same time.
SETTING A PROGRAMME
1. Turn the programme knob to switch the
appliance on and set the programme:
• The indicator of the button
flashes.
• The display shows the programme duration.
2. If necessary, change the temperature and the
spin speed or add available options. When you
activate an option, the indicator of the set
option comes on.
Autosense function
At the start of the programme, During the washing
phase the programme duration is automatically
calculated and can be greatly reduced if the laundry
load is lower than the maximum load capacity. (e.g.
Cotton 30° programme , maximum load capacity 6
kg , the default programme duration exceeds 2
hours, in case of actual load 2 kg, the program
duration will be reduced to only 1 hour 20 min).
STARTING A PROGRAMME WITHOUT THE
DELAY START
Press the button
•
•
•
.
stops to
The indicator of the button
flash and stays on.
The programme starts, the door locks, the
indicator
is on.
The programme time decreases with steps
of one minute.
The drain pump can operate for a
short time at the beginning of the
washing cycle.
STARTING A PROGRAMME WITH THE DELAY
START OPTION
1. Press the button Partenza posticipata
again
and again until the display shows the delay you
want to set. The delay start indicator comes on.
2. Press the button Avvio/Pausa
•
•
•
:
The door is locked and the indicator
is
on.
The appliance starts the countdown.
When the countdown is completed, the
programme starts automatically.
You can cancel or change the set of
the Partenza posticipata
option
before you press the button Avvio/
Pausa
. After pressing the button
Avvio/Pausa
you can only cancel
the Avvio/Pausa option.
To cancel the Partenza posticipata
option:
a. Press the button Avvio/Pausa
to set
the appliance to pause. The indicator of
button
flashes.
b. Press the button Partenza posticipata
until the delay time indicator goes off.
Press the Avvio/Pausa button
again to
start the programme immediately.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before the
programme carries them out.
1. Press the Avvio/Pausa
the running programme.
The related indicator flashes.
2. Change the options.
button to interrupt
3. Press the Avvio/Pausa
The programme continues.
button again.
CANCELLING A RUNNING PROGRAMME
1. Turn the programme knob to position
to
cancel the programme and to deactivate the
appliance.
2. Turn the programme knob again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. in
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
OPENING THE DOOR WHEN THE DELAY
START OPERATES
While the delay start operates, the appliance door
is locked and the panel shows the indicator
1. Press Avvio/Pausa
.
to pause the appliance.
2. Wait until the door lock indicator
3. Open the door.
4. Close the door.
goes off.
5. Press Avvio/Pausa
again.
The delay start continues to operate.
OPENING THE DOOR WHEN THE
PROGRAMME OPERATES
While the programme operates, the appliance door
is locked and the indicator
appears.
CAUTION! If the temperature and
level of the water in the drum are too
high, you cannot open the door.
1. Turn the programme knob to position
deactivate the appliance.
to
2. Wait some minutes until the indicator
goes
off and then open carefully the appliance door.
3. Close the appliance door.
4. Set the programme again.
13
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
• In the display three flashing zeros come on.
•
The indicator of the Avvio/Pausa
•
•
•
The door lock indicator
goes off.
You can open the door.
Remove the laundry from the appliance. Make
sure that the drum is empty.
Close the water tap.
•
goes off.
•
Turn the programme knob to the position
to
deactivate the appliance.
• Keep the door ajar, to prevent the mildew and
odours.
The washing programme is completed, but
there is water in the drum:
• The drum turns regularly to prevent the creases
in the laundry.
is on. The door
The door lock indicator
stays locked.
• You must drain the water to open the door.
To drain the water:
•
1. Turn the programme knob to spinning or
draining programme.
. If
2. Press the button Avvio/Pausa
necessary, decrease the spin speed.
The appliance spins and drains or only drains.
3. When the programme is completed and the
door lock indicator
the door.
goes off, you can open
4. Turn the programme knob to the position
deactivate the appliance.
to
The appliance drains and spins
automatically after approximately 18
hours (except for Wool programme).
STAND-BY
Once the programme has finished, after a few
minutes the energy saving system will be enabled.
The brightness of the lights is reduced.
By pressing any button the appliance will come out
of the energy saving status.
HINTS AND TIPS
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on the
laundry care labels.
• Do not wash white and coloured items together.
• Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
• Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn multilayered fabrics, wool and items with
painted illustrations inside out.
• Remove hard stains with a special detergent.
• Wash and pre-treat heavy soil stains before
putting items in drum
• Be careful with the curtains. Remove the hooks
and put the curtains in a washing bag or
pillowcase.
• Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
• A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
14
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (40
°C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
•
If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
• Always start a washing programme with the
maximum load of laundry allowed.
• If necessary, use a stain remover when you set a
programme with a low temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
DOOR SEAL
EXTERNAL CLEANING
Clean the appliance with soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
Regularly examine the seal and remove all objects
from the inner part.
CLEANING THE DETERGENT DISPENSER
Clean regularly the washing powder and additive
dispenser drawer.
To clean the detergent drawer it is necessary to
remove it from its site.
Open the drawer.
Always obey the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
• Remove all laundry from the drum.
• Select the cotton programme with the highest
temperature with a small quantity of detergent.
Press the catch downwards as described in the
graphic and pull it out.
15
Open the pump door.
Place a container close
to the pump to collect
any spillage.
Remove the top part of
the additive compartment
to aid cleaning.
Flush it out under a tap, to
remove any traces of accumulated powder.
Make sure that all washing
powder residue is removed from the upper and
lower part of the recess.
Use a small brush to clean
the recess.
Unscrew carefully the
drain filter to drain out the
water.
When no more water
comes out, remove the
filter. If necessary, use
plier hands carefully, do
not use the jaws.
1
2
Close the drawer and run
the rinse programme without any clothes in the
drum.
Always keep a rag nearby to dry up
any water spillage.
Clean the filter under a
tap, to remove any traces
of fluff.
CLEANING THE DRAIN FILTER
The pump should be inspected regularly and
particularly if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during
draining phase due to objects such as safety
pins, coins and so on blocking the pump;
• a problem with water draining is detected (see
chapter 'Troubleshooting' for more details).
Remove foreign bodes
and fluff from the filter
seat and from the pump
impeller.
Check carefully whether
the pump impeller rotates
(it rotates jerkily).
CAUTION! Switch the appliance off
and remove the mains plug from the
socket.
Proceed as follows:
• Unplug the appliance.
• If it is necessary, wait until the water has cooled
down.
2
1
16
Replace the filter into the
pump by inserting it correctly into the special
guides.
Screw firmly the filter.
Close the pump door.
CAUTION! Never remove the filter
during a washing cycle, always wait
until the appliance has finished the
cycle, and is empty.
CAUTION! When refitting the filter,
ensure it is securely re-tightened so as
to stop leaks and young children being
able to remove it.
CLEANING THE INLET HOSE AND THE VALVE
FILTER
1
2
EMERGENCY DRAIN
Because of a malfunction, the appliance cannot
drain the water.
If this occurs, do steps (1) through (8) of 'Cleaning
the drain filter'. If necessary, clean the pump.
When you drain the water with the emergency drain
procedure, you must activate the drain system
again:
1. Put 2 litres of water in the main wash
compartment of the detergent dispenser.
2. Start the programme to drain the water.
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0° C, remove the
remaining water from the inlet hose and the drain
pump.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of the
hose.
4. Empty the drain pump. Refer to the emergency
drain procedure.
5. When the drain pump is empty, install the inlet
hose again.
WARNING! Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
3
45°
20°
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during
operation.
First try to find a solution to the problem (refer to
the table). If the problem persists, contact the
Authorised Service Center
WARNING! Deactivate the appliance
before you do the checks.
17
POSSIBLE FAILURES
Problem
The programme does not
start.
Possible solution
•
•
•
•
•
•
•
The appliance does not fill
with water properly.
•
•
•
•
•
•
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter of the inlet hose & the filter of the valve are
not clogged. Refer to "Care & Cleaning"
Make sure that the drain hose has no kinks or bends.
Make sure that the connection of the drain hose is correct.
The appliance does not fill
with water and drain immediately.
•
Make sure that the drain hose is in the correct position. The hose
may be too low.
The appliance does not
drain the water.
•
•
•
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".
Make sure that the connection of the drain hose is correct.
Set the drain programme if you set a programme without drain
phase.
Set the drain programme if you set an option which ends with water
in the tub.
•
•
•
The spin phase does not
operate or the washing cycle lasts longer than usually.
•
•
•
•
There is water on the floor.
•
•
•
You cannot open the appliance door.
18
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the fuse box.
Make sure that the Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of
countdown.
Deactivate the Child Lock function if it is on.
Make sure that the mains plug is connected to the mains socket.
•
•
Set the spin option.
Set the drain option if you set an option which ends with water in
the drum.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
Make sure that the couplings of the water hoses are tight and there
is not water leakages.
Make sure that the drain hose have no damages.
Make sure you use the correct detergent and the correct quantity of
it.
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
Problem
The appliance makes an
unusual noise.
Possible solution
•
•
•
Make sure the levelling of the appliance is correct. Refer to "Installation".
Make sure that the packaging and/or the transit bolts are removed.
Refer to "Installation".
Add more laundry in the drum. The load may be too small.
The cycle is shorter than
the time displayed.
•
The appliance calculates a new time according to the laundry load.
See the "Auto sense function" at daily use chapter.
The cycle is longer than
the time displayed.
•
An unbalanced laundry load increases the duration time. This is a
normal behaviour of the appliance.
The washing results are
not satisfactory.
•
•
•
•
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
•
Make sure that you press only the wanted button(s).
You cannot set an option.
After the check, activate the appliance. The programme continues from the point of interruption.
If the problem occurs again, contact the Authorised Service Centre.
If the appliance shows other alarm codes (the indicator of button
flashes in red). Deactivate and activate the appliance. If the problem continues, contact the Authorised Service Centre.
TECHNICAL DATA
Dimension
Width/ Height/ Depth/ Total depth
596 mm/ 854 mm/ 607 mm/ 643 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
220-230 V
2000 W
10 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure
0.5 bar (0.05 MPa)
8 bar (0,8 MPa)
Minimum
Maximum
Cold water
Water supply 1)
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
PRODUCT INFORMATION SHEET IN REFERENCE TO E.U. REGULATION
1369/2017
Product Information Sheet
19
Trade Mark
Model
Rated capacity in kg
Energy efficiency class
ZOPPAS
PWF6082WEX, PNC
914909171
6
A+++
Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and
partial load, and the consumption of the low-power modes. Actual
energy consumption will depend on how the appliance is used.
153
Energy consumption of the standard 60°C cotton programme at full
load in kWh
0,86
Energy consumption of the standard 60°C cotton programme at partial load in kWh
0,56
Energy consumption of the standard 40°C cotton programme at partial load kWh
0,52
Power consumption of the off-mode in W
0,48
Power consumption in left-on mode in W
0,48
Water consumption in litres per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and
partial load. Actual water consumption will depend on how the appliance is used.
9535
Spin-drying efficiency class on a scale from G (least efficient) to A
(most efficient)
D
Maximum spin speed in rpm
751
Remaining moisture content in %
70
The 'standard 60 °C cotton programme' and the 'standard 40 °C
cotton programme' are the standard washing programmes to which
the information in the label and the fiche relates, these programmes
are suitable to clean normally soiled cotton laundry and they are the
most efficient in terms of combined energy and water consumption.
-
Programme time of the standard 60°C cotton programme at full load
in minutes
230
Programme time of the standard 60°C cotton programme at partial
load in minutes
190
Programme time of the "standard 40°C cotton programme at partial
load in minutes
190
Duration of the left on mode in minutes
5
Airborne acoustical noise emission in db(A) washing
59
Airborne acoustical noise emission in db(A) spinning
75
Built in appliance Y/N
No
The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC .
20
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
21
*
22
23
148207700-D-192019
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement