Aeg SCE81928TS User Manual
User Manual
Fridge Freezer
1. SAFETY INFORMATION............................................................................................. 2
2. SAFETY INSTRUCTIONS.............................................................................................4
3. INSTALLATION............................................................................................................6
4. OPERATION.................................................................................................................9
5. DAILY USE.................................................................................................................. 11
6. HINTS AND TIPS........................................................................................................14
7. CARE AND CLEANING.............................................................................................15
8. TROUBLESHOOTING............................................................................................... 17
9. NOISES....................................................................................................................... 20
10. TECHNICAL DATA..................................................................................................21
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler – features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service and repair information:
Register your product for better service:
Buy Accessories, Consumables and Original spare parts for your appliance:
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children aged from 3 to 8 years are allowed to load
and unload the appliance provided that they have
been properly instructed.
This appliance may be used by persons with very
extensive and complex disabilities provided that they
have been properly instructed.
Children of less than 3 years of age should be kept
away from the appliance unless continuously
Do not let children play with the appliance.
Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
Keep all packaging away from children and dispose of
it appropriately.
1.2 General Safety
This appliance is intended to be used in household
and similar applications such as:
– Farm houses; staff kitchen areas in shops, offices
and other working environments;
– By clients in hotels, motels, bed and breakfast and
other residential type environments.
To avoid contamination of food respect the following
– do not open the door for long periods;
– clean regularly surfaces that can come in contact
with food and accessible drainage systems;
store raw meat and fish in suitable containers in the
refrigerator, so that it is not in contact with or drip
onto other food.
WARNING: Keep ventilation openings, in the
appliance enclosure or in the built-in structure, clear of
WARNING: Do not use mechanical devices or other
means to accelerate the defrosting process, other
than those recommended by the manufacturer.
WARNING: Do not damage the refrigerant circuit.
WARNING: Do not use electrical appliances inside the
food storage compartments of the appliance, unless
they are of the type recommended by the
Do not use water spray and steam to clean the
Clean the appliance with a moist soft cloth. Only use
neutral detergents. Do not use abrasive products,
abrasive cleaning pads, solvents or metal objects.
When the appliance is empty for long period, switch it
off, defrost, clean, dry and leave the door open to
prevent mould from developing within the appliance.
Do not store explosive substances such as aerosol
cans with a flammable propellant in this appliance.
If the supply cord is damaged, it must be replaced by
the manufacturer, its Authorised Service Centre or
similarly qualified persons in order to avoid a hazard.
2.1 Installation
Only a qualified person must
install this appliance.
• Remove all the packaging.
• Do not install or use a damaged
• Do not use the appliance before
installing it in the built-in structure
due to safety manner.
• Follow the installation instructions
supplied with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Make sure the air can circulate around
the appliance.
• At first installation or after reversing
the door wait at least 4 hours before
connecting the appliance to the
power supply. This is to allow the oil
to flow back in the compressor.
• Before carrying out any operations on
the appliance (e.g. reversing the
door), remove the plug from the
power socket.
• Do not install the appliance close to
radiators or cookers, ovens or hobs.
• Do not expose the appliance to the
• Do not install the appliance where
there is direct sunlight.
• Do not install this appliance in areas
that are too humid or too cold.
• When you move the appliance, lift it
by the front edge to avoid scratching
the floor.
• The appliance contains a bag of
desiccant. This is not a toy. This is not
food. Please dispose of it
2.2 Electrical connection
Risk of fire and electric
When positioning the
appliance, ensure the supply
cord is not trapped or
Do not use multi-plug
adapters and extension
• The appliance must be earthed.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
• Always use a correctly installed
shockproof socket.
• Make sure not to cause damage to
the electrical components (e.g. mains
plug, mains cable, compressor).
Contact the Authorised Service
Centre or an electrician to change the
electrical components.
• The mains cable must stay below the
level of the mains plug.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
2.3 Use
Risk of injury, burns, electric
shock or fire.
The appliance contains flammable
gas, isobutane (R600a), a natural gas with
a high level of environmental
compatibility. Be careful not to cause
damage to the refrigerant circuit
containing isobutane.
• Do not change the specification of
this appliance.
• Do not put electrical appliances (e.g.
ice cream makers) in the appliance
unless they are stated applicable by
the manufacturer.
• If damage occurs to the refrigerant
circuit, make sure that there are no
flames and sources of ignition in the
room. Ventilate the room.
• Do not let hot items to touch the
plastic parts of the appliance.
• Do not put soft drinks in the freezer
compartment. This will create
pressure on the drink container.
• Do not store flammable gas and
liquid in the appliance.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Do not touch the compressor or the
condenser. They are hot.
• Do not remove or touch items from
the freezer compartment if your hands
are wet or damp.
• Do not freeze again food that has
been thawed.
• Follow the storage instructions on the
packaging of frozen food.
• Wrap the food in any food contact
material before putting it in the
freezer compartment.
2.4 Internal lighting
Risk of electric shock.
• The type of lamp used for this
appliance is for household appliances
only. Do not use it for house lighting.
2.5 Care and cleaning
Risk of injury or damage to
the appliance.
• Before maintenance, deactivate the
appliance and disconnect the mains
plug from the mains socket.
• This appliance contains hydrocarbons
in the cooling unit. Only a qualified
person must do the maintenance and
the recharging of the unit.
• Regularly examine the drain of the
appliance and if necessary, clean it. If
the drain is blocked, defrosted water
collects in the bottom of the
• Please note that self-repair or nonprofessional repair can have safety
consequences and might void the
2.7 Disposal
Risk of injury or suffocation.
• Disconnect the appliance from the
mains supply.
• Cut off the mains cable and discard it.
• Remove the door to prevent children
and pets to be closed inside of the
• The refrigerant circuit and the
insulation materials of this appliance
are ozone-friendly.
• The insulation foam contains
flammable gas. Contact your
municipal authority for information on
how to discard the appliance
• Do not cause damage to the part of
the cooling unit that is near the heat
2.6 Service
• To repair the appliance contact the
Authorised Service Centre. Use
original spare parts only.
Refer to Safety chapters.
Refer to installation
instruction document to
install your appliance.
Fix the appliance in
accordance with installation
instruction document to
avoid a risk of instability of
the appliance.
3.1 Location
To ensure best performance, install the
appliance well away from sources of heat
such as radiators, boilers, direct sunlight
etc. Make sure that air can circulate freely
around the back of the cabinet.
3.2 Positioning
Install the appliance in a dry, well
ventilated indoors where the ambient
temperature corresponds to the climate
class indicated on the rating plate of the
Ambient temperature
+10°C to + 32°C
+16°C to + 32°C
+16°C to + 38°C
Ambient temperature
+16°C to + 43°C
Some functional problems
might occur for some types
of models when operating
outside of that range. The
correct operation can only
be guaranteed within the
specified temperature
range. If you have any
doubts regarding where to
install the appliance, please
turn to the vendor, to our
customer service or to the
nearest Authorised Service
3.3 Electrical Connection
Any electrical work required
to install this appliance
should be carried out by a
qualified electrician or
competent person.
This appliance must be
The manufacturer declines
any liability should these
safety measures not be
The wires in the mains lead are coloured
in accordance with the following code:
• A - green and yellow: Earth
• C - brown: Live
• D - blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
1. Connect the wire coloured green and
yellow to the terminal marked either
with the letter “E“ or by the earth
or coloured green and
2. Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3. Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4. Check that no cut, or stray strands of
wire is present and the cord clamp
(E) is secure over the outer sheath.
Make sure the electricity supply
voltage is the same as that indicated
on the appliance rating plate.
5. Switch on the appliance.
The appliance is supplied with a 13 amp
fuse (B). In the event of having to change
the fuse in the plug supplied, a 13 amp
ASTA approved (BS 1362) fuse must be
A cut off plug inserted into a
13 amp socket is a serious
safety (shock) hazard. Ensure
that it is disposed of safely.
3.4 Ventilation requirements
The airflow behind the appliance must
be sufficient.
5 cm
3. Slide in the SpinView® clamps on the
glass shelf's back edge.
200 cm2
200 cm2
4. Mount the SpinView® shelf. Make
sure that the clamp pins fit into
special indentations at the base of
the shelf. Check if the SpinView®
shelf is mounted properly by moving
it gently forwards and backwards.
Refer to the assembly
instructions for the
3.5 Installing the SpinView®
Clean the accessory with a
soft moist cloth before first
use. Maximum load allowed
on the shelf is 15 kg.
1. Remove one of the glass shelves
from the fridge.
2. Remove the back trim from the glass
5. Place the shelf with the clamps inside
the fridge. Push the shelf until the
clamps lock inside the compartment.
4.1 Control Panel
Freezer Temperature warmer button
Freezer Temperature colder button
Fridge Temperature warmer button
7 Fridge Temperature colder button
It is possible to change predefined
sound of buttons by pressing together
Mode and temperature colder button for
a few seconds. Change is reversible.
4.2 Display
4.3 Switching on
1. Connect the mains plug to the power
2. Press the appliance ON/OFF if the
display is off. The temperature
indicators show the set default
The alarm buzzer could
operate after few seconds.
To reset the alarm refer to
"High temperature alarm".
To select a different set temperature
refer to "Temperature regulation".
A. Fridge compartment indicator
B. Timer indicator
/Temperature indicator
C. ON/OFF indicator
D. Coolmatic function
E. Holiday mode
F. Frostmatic function
G. Temperature indicator
H. Freezer compartment indicator
I. Alarm indicator
J. ChildLock function
K. DrinksChill function
L. DYNAMICAIR function
If "dEMo" appears on the display, refer
to "Troubleshooting" .
4.4 Switching off
1. Press the appliance ON/OFF for 5
The display switches off.
2. Disconnect the mains plug from the
power socket.
4.5 Temperature regulation
Set the temperature of the appliance by
pressing the temperature regulators.
Default set temperature:
• +5°C for the fridge
• -18°C for the freezer
The temperature indicators show the set
The set temperature will be
reached within 24 hours.
After a power failure the set
temperature remains stored.
4.6 Switching on the fridge
To switch on the fridge it is enough to
press the fridge temperature regulator.
To switch on the fridge in the other way:
1. Press Mode until the corresponding
icon appears.
The Fridge OFF indicator flashes.
2. Press OK to confirm.
The fridge OFF indicator goes off.
To select a different set
temperature refer to
"Temperature regulation".
4.7 Switching off the fridge
1. Press Mode until the corresponding
icon appears.
The fridge OFF indicator and the fridge
compartment indicator flash.
The fridge temperature indicator shows
2. Press OK to confirm.
The fridge OFF indicator is shown.
4.8 Coolmatic function
If you need to insert a large amount of
warm food, for example after doing the
grocery shopping, we suggest activating
the Coolmatic function to chill the
products more rapidly and to avoid
warming the other food which is already
in the refrigerator.
1. Press the Mode until the
corresponding icon appears.
The Coolmatic indicator flashes.
2. Press the OK to confirm.
The Coolmatic indicator is shown.
The Coolmatic function shuts off
automatically after approximately 6
To switch off the function before its
automatic end, repeat the procedure.
The function switches off by
selecting a different fridge
set temperature.
4.9 Holiday mode
This mode allows you to keep the
appliance closed and empty during a
long holiday period without the
formation of bad odours.
1. Press the Mode until the
corresponding icon appears.
The Holiday indicator flashes. The
temperature indicator shows the set
2. Press the OK to confirm.
The Holiday indicator is shown.
This mode switches off after
selecting a different
4.10 Frostmatic function
The Frostmatic function accelerates the
freezing of fresh food and, at the same
time, protects foodstuffs already stored
from undesirable warming.
1. To activate this function press the
Mode button until the corresponding
icon appears.
The Frostmatic indicator flashes.
2. Press the OK button to confirm.
The Frostmatic indicator is shown.
This function stops automatically after 52
To switch off the function before its
automatic end repeat the procedure
until the Frostmatic indicator turns off.
The function switches off by
selecting a different set
4.11 ChildLock function
Activate the ChildLock function to lock
the buttons from unintentional
1. Press Mode until the corresponding
icon appears.
The ChildLock indicator flashes.
2. Press OK to confirm.
The ChildLock indicator is shown.
To deactivate the ChildLock function,
repeat the procedure until the ChildLock
indicator goes off.
flashing the alarm icon and freezer
temperature indicators, and sounding of
4.12 DrinksChill function
Press any button.
The buzzer switches off.
The freezer temperature indicator shows
the highest temperature reached for a
few seconds, then displays the set
temperature again.
The DrinksChill function is to be used to
set an acoustic alarm at the preferred
time, useful for example when a recipe
requires to cool down food products for
a certain period of time.
It is also useful when a reminder is
needed in order not to forget the bottles
placed in the freezer for fast cooling.
1. Press Mode until the corresponding
icon appears.
The DrinksChill indicator flashes.
The Timer shows the set value (30
minutes) for a few seconds.
2. Press the Timer regulator to change
the Timer set value from 1 to 90
3. Press OK to confirm.
TheDrinksChill indicator is shown.
The Timer start to flash (min).
At the end of the countdown the
DrinksChill indicator flashes and an
audible alarm sounds. Press OK to switch
off the sound and terminate the function.
To switch off the function repeat the
procedure until the DrinksChill goes off.
It is possible to change the
time at any time during the
countdown and at the end
by pressing the Temperature
colder button and the
Temperature warmer button.
4.13 High temperature alarm
An increase in the temperature in the
freezer compartment (for example due to
an earlier power failure) is indicated by
The alarm indicator
continues to flash until the
normal conditions are
4.14 Door open alarm
If the refrigerator door is left open for
approximately 5 minutes, the sound is on
and alarm indicator flashes.
The alarm stops after closing the door.
During the alarm, the sound can be
muted by pressing any button.
4.15 DYNAMICAIR function
To switch on the function:
1. Press the Mode button until the
corresponding icon appears.
The DYNAMICAIR indicator flashes.
2. Press the OK button to confirm.
The DYNAMICAIR indicator is shown.
To switch off the function repeat the
procedure until the DYNAMICAIR
indicator icon goes off.
If the function is activated
automatically the
DYNAMICAIR indicator is
not shown (refer to "Daily
The activation of the
increase the energy
Refer to Safety chapters.
5.1 Cleaning the interior
Before using the appliance for the first
time, the interior and all internal
accessories should be washed with
lukewarm water and some neutral soap
to remove the typical smell of a brandnew product, then dried thoroughly.
Do not use detergents,
abrasive powders, chlorine
or oil-based cleaners as they
will damage the finish.
5.2 Positioning of the door
The door of the fridge compartment is
equipped with runners which enable
repositioning of the door shelves
according to individual preferences.
Do not move the glass shelf
above the vegetable drawer
to ensure correct air
5.4 SpinView® shelf
Do not place the shelf on
the highest level because
the stored products can hit
the DYNAMICAIR device
and topple over.
To reposition the door shelves, please
slide the door shelves carefully according
to arrows.
The SpinView® shelf rotates 360 degrees
in both directions for better visibility and
reachability of the stored products.
5.3 Movable shelves
To rotate the shelf grab it by the brim
and slowly spin it clockwise or counterclockwise.
The walls of the refrigerator are
equipped with a series of runners so that
the shelves can be positioned as desired.
This appliance is also equipped with a
shelf consisting of two parts. The front
half of the shelf can be placed under the
second half to make better use of space.
To fold the shelf:
1. Take out the front half gently.
2. Slide it into the lower rail and under
the second half.
Always return the shelf to its neutral
position before closing the door.
Do not spin the shelf too fast
and do not place your
fingers under the shelf or on
the sides.
Do not use SpinView® shelf
as an external tray.
The glass shelf mounted with the
SpinView® shelf can be positioned on
different levels inside the fridge.
It is possible to switch on the
device manually when
needed (refer to
"DYNAMICAIR function").
stops when the door is open
and restarts immediately
after the door closing.
5.6 Freezing and storage of
frozen food
To re-position the shelf put your hand
under the back of the shelf, push it
upwards to release the clamps and
simultaneously pull the glass shelf out
from the cabinet.
The refrigerator compartment is
equipped with a device that allows rapid
cooling of food and keeps a more
uniform temperature in the
This device activates automatically when
needed, for example for a quick
temperature recovery after door opening
or when the ambient temperature is
The freezer compartment is suitable for
freezing fresh food and storing frozen
and deep-frozen food for a long time.
When first starting-up or after a period
out of use, before putting the products
in the compartment let the appliance run
at least 2 hours with the Frostmatic
function turned on. To freeze fresh food
activate the Frostmatic function at least
24 hours before placing the food to be
frozen in the freezer compartment.
To freeze fresh food place it in the top
The maximum amount of food that can
be frozen in 24 hours is specified on the
rating plate, a label located on the
inside of the appliance.
The freezing process lasts 24 hours,
during this period do not add other food
to be frozen.
In the event of accidental defrosting, for
example due to a power failure, if the
power has been off for longer than the
value shown in the technical
characteristics chart under "rising time",
the defrosted food must be consumed
quickly or cooked immediately and then
re-frozen (after cooling).
5.7 Thawing
Do not use metallic
instruments to remove the
trays from the freezer.
Deep-frozen or frozen food, prior to
being used, can be thawed in the
refrigerator compartment or at room
temperature, depending on the time
available for this operation.
1. Fill these trays with water
2. Put the ice trays in the freezer
Small pieces may even be cooked still
frozen, directly from the freezer: in this
case, cooking will take longer.
The freezer contains at least one cold
accumulator which increases storage
time in the event of a power cut or
5.8 Ice-cube production
5.9 Cold accumulators
This appliance is equipped with one or
more trays for the production of icecubes.
6.1 Normal operating sounds
The following sounds are normal during
• A faint gurgling and bubbling sound
from coils sound when refrigerant is
• A whirring and pulsating sound from
the compressor when refrigerant is
• A sudden cracking noise from inside
appliance caused by thermic
dilatation (a natural and not
dangerous physical phenomenon).
• A faint click noise from the
temperature regulator when the
compressor switches on or off.
6.2 Hints for energy saving
• Eco mode / default setting preserves
fresh and frozen foods while saving
• Fresh Food Compartment (Fridge):
Most efficient use of energy is
ensured in the configuration with the
drawers in the bottom part of the
appliance and shelves evenly
distributed. Position of the door bins
does not affect energy consumption.
• Frozen Compartment (Freezer): The
internal configuration of the appliance
is the one that ensures the most
efficient use of energy.
• Do not remove the cold accumulators
from the freezer basket.
• If the ambient temperature is high
and the temperature control is set to
low temperature and the appliance is
fully loaded, the compressor may run
continuously, causing frost or ice
formation on the evaporator. In this
case, set the temperature control
toward higher temperature to allow
automatic defrosting and to save
energy this way.
• Do not open the door frequently or
leave it open longer than absolutely
6.3 Hints for fresh food
• Do not store warm food or
evaporating liquids in the refrigerator.
• Cover or wrap the food, particularly if
it has a strong flavour.
• Position food so that air can circulate
freely around it.
6.4 Hints for refrigeration
Useful hints:
• Meat (all types): wrap in a suitable
packaging and place it on the glass
shelf above the vegetable drawer.
Store meat for at most 1-2 days.
• Cooked foods, cold dishes: cover and
place on any shelf.
• Fruit and vegetables: clean
thoroughly and place in a special
drawer. Bananas, potatoes, onions
and garlic must not be kept in the
refrigerator if not packed.
• Butter and cheese: place in a special
airtight container or wrap in an
aluminium foil or a polythene bag to
exclude as much air as possible.
• Bottles: close with a cap and place on
the door bottle shelf, or (if available)
on the bottle rack.
6.5 Hints for freezing
• Freeze only top quality, fresh and
thoroughly cleaned food products.
• For more efficient freezing and
thawing divide food into small
• Wrap the food in aluminium foil or
polythene. Make sure that the
packages are airtight.
• To avoid increase in temperature of
already frozen food, do not place
fresh unfrozen food directly next to it.
• Lean foods store better and longer
than fatty ones. Salt reduces the
storage life of food.
• Do not eat ice cubes, water ices or ice
lollies immediately after taking them
out of the freezer. Risk of frostbites.
• It is advisable to show the freezing
date on each individual pack to
enable you to keep tab of the storage
6.6 Hints for storage of frozen
• Make sure that the commercially
frozen food products were adequately
stored by the retailer.
• Make sure that frozen foodstuffs are
transferred from the food store to the
freezer in the shortest possible time.
• Once defrosted, food deteriorates
rapidly and cannot be refrozen.
• Do not exceed the storage period
indicated by the food manufacturer.
Refer to Safety chapters.
7.1 General warnings
Unplug the appliance before
carrying out any
maintenance operation.
This appliance contains
hydrocarbons in its cooling
unit; maintenance and
recharging must therefore
only be carried out by
authorized technicians.
The accessories and parts of
the appliance are not
suitable for washing in a
7.2 Periodic cleaning
Do not pull, move or
damage any pipes and/or
cables inside the appliance.
Do not damage the cooling
The equipment has to be cleaned
1. Clean the inside and accessories with
lukewarm water and some neutral
2. Regularly check the door seals and
wipe them clean to ensure they are
clean and free from debris.
3. Rinse and dry thoroughly.
4. If accessible, clean the condenser
and the compressor at the back of
the appliance with a brush.
This will improve the performance of
the appliance and save electricity
7.3 Defrosting of the
Frost is automatically eliminated from the
evaporator of the refrigerator
compartment every time the motor
compressor stops, during normal use.
The defrost water drains out through a
trough into a special container at the
back of the appliance, over the motor
compressor, where it evaporates.
It is important to periodically clean the
defrost water drain hole in the middle of
the refrigerator compartment channel to
prevent the water overflowing and
dripping onto the food inside.
7.4 Defrosting of the freezer
The freezer compartment is frost free.
This means that there is no build up of
frost when it is in operation, neither on
the internal walls, nor on the foods.
7.5 Removing the SpinView®
Clean the accessory with a
soft moist cloth. Milk based
food may stain the finish.
The SpinView® shelf can be removed
from the glass shelf for cleaning.
To remove the shelf:
1. Lift the front of the SpinView® shelf
2. Pull the SpinView® shelf in the shown
direction to unmount it from the
Do not disassemble the
SpinView® shelf. Do not
clean the SpinView® shelf in
the dishwasher.
7.6 Periods of non-operation
When the appliance is not in use for long
periods, take the following precautions:
1. Disconnect the appliance from
electricity supply.
2. Remove all food.
3. Clean the appliance and all
4. Leave the door/doors open to
prevent unpleasant smells.
If you want to keep the
appliance switched on, ask
somebody to check it once
in a while to prevent the
food inside from spoiling in
case of a power failure.
We recommend activating
Holiday Mode.
Refer to Safety chapters.
8.1 What to do if...
Possible cause
The appliance does not operate.
The appliance is switched
Switch on the appliance.
The mains plug is not con- Connect the mains plug to the
nected to the mains socket mains socket correctly.
There is no voltage in the
mains socket.
Audible or visual alarm is on. The cabinet has been recently switched on or the
temperature is too high.
Connect a different electrical
appliance to the mains socket.
Contact a qualified electrician.
Refer to "High temperature
The temperature in the ap- Contact a qualified electrician
pliance is too high.
or contact the nearest Authorised Service Centre.
The door is left open.
Close the door. Refer to "Door
open alarm"
symbol is shown
instead of numbers on the
Temperature Display.
Temperature sensor problem.
Contact the nearest Authorised Service Centre (the cooling system will continue to
keep food products cold, but
temperature adjustment will
not be possible).
The lamp does not work.
The lamp is in stand-by.
Close and open the door.
The lamp is defective.
Contact the nearest Authorised Service Centre.
Possible cause
The compressor operates
Temperature is set incorrectly.
Refer to "Operation".
Many food products were
put in at the same time.
Wait few hours and then check
the temperature again.
The room temperature is
too high.
Refer to climate class chart on
the rating plate.
Food products placed in
the appliance were too
Allow food products to cool to
room temperature before storing.
The door is not closed cor- Refer to "Closing the door".
The "Frostmatic function"
or "Coolmatic function" is
switched on.
There is too much frost and
Refer to "Frostmatic function"
or "Coolmatic function".
The door is not closed cor- Refer to "Closing the door".
rectly or the gasket is deformed/dirty.
The water drainage plug is Position the water drainage
not correctly positioned.
plug in the correct way.
Appliance is fully loaded
and it is set to the lowest
Set a higher temperature. Refer to "Operation".
Temperature set in the ap- Set a higher temperature. Repliance is too low and the fer to "Operation"
ambient temperature is
too high.
Temperature is set incorrectly.
Refer to "Operation" .
The compressor does not
This is normal, no error has The compressor starts after a
start immediately after
period of time.
pressing the "Frostmatic" or
"Coolmatic", or after changing the temperature.
Water flows on the rear
plate of the refrigerator.
During the automatic defrosting process, frost
melts on the rear plate.
This is correct.
Water flows inside the refrig- Food products prevent the Make sure that food products
water to flow into the wado not touch the rear plate.
ter collector.
Possible cause
The water outlet is clogged.
Clean the water outlet.
Water flows on the floor.
The melting water outlet is Attach the melting water outnot connected to the
let to the evaporative tray.
evaporative tray above the
Temperature cannot be set.
The "Frostmatic function"
or "Coolmatic function" is
switched on.
dEMo appears on the display.
The appliance is in demon- Keep the OK pressed for apstration mode.
proximately 10 seconds until a
long sound is heard and display shuts off for a short time.
The temperature in the appliance is too low/too high.
The temperature regulator Set a higher/lower temperais not set correctly.
Switch off "Frostmatic function" or "Coolmatic function"
manually, or wait until the
function resets automatically
to set the temperature. Refer
to "Frostmatic function" or
"Coolmatic function".
The door is not closed cor- Refer to "Closing the door".
The food products' temperature is too high.
Let the food products temperature decrease to room temperature before storage.
Many food products are
stored at the same time.
Add less food products at the
same time.
The door has been
opened often.
Open the door only if necessary.
The "Frostmatic function"
or "Coolmatic function" is
switched on.
Refer to "Frostmatic function"
or "Coolmatic function".
There is no cold air circula- Make sure that there is cold air
tion in the appliance.
circulation in the appliance.
If the advice does not lead
to the desired result, contact
the nearest Authorised
Service Centre.
8.2 Replacing the lamp
The appliance is equipped with a longlife
LED interior light.
Only service is allowed to replace the
lighting device. Contact your Authorised
Service Centre.
8.3 Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to
assembly instructions.
3. If necessary, replace the defective
door gaskets. Contact the Authorised
Service Centre.
There are some sounds during normal running (compressor, refrigerant circulation).
10.1 Technical data
Dimensions of the recess
1894 mm
560 mm
550 mm
230 - 240 V
50 Hz
Rising time
21 h
The technical information is situated in
the rating plate, on the external or
internal side of the appliance and on the
energy label.
Recycle materials with the symbol .
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF