BenQ MW732 PROJECTOR User Manual

BenQ MW732 PROJECTOR User Manual
MX731/MW732/MH733
Digital Projector
User Manual
V 1.02
Warranty and Copyright information
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal usage and
storage.
Proof of purchase date will be required with any warranty claim. In the event this product is found to be
defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be
replacement of any defective parts (labor included). To obtain warranty service, immediately notify the
dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in accordance
with BenQ's written instructions, especially the ambient humidity must be in-between 10% and 90%,
temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the
projector in a dusty environment. This warranty gives you specific legal rights, and you may have other
rights which vary from country to country.
For other information, please visit www.BenQ.com.
Copyright
Copyright © 2017 by BenQ Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect
to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are
copyrights of their respective companies or organizations.
Patents
Please go to http://patmarking.benq.com/ for the details on BenQ projector patent coverage.
2
Warranty and Copyright information
Table of Contents
Warranty and Copyright information ................................................................................ 2
Important safety instructions .............................................................................................. 4
Introduction .......................................................................................................................... 7
Shipping contents ....................................................................................................................................... 7
Projector exterior view ............................................................................................................................ 8
Controls and functions.............................................................................................................................. 9
Positioning your projector ................................................................................................. 12
Choosing a location ................................................................................................................................. 12
Obtaining a preferred projected image size....................................................................................... 13
Mounting the projector .......................................................................................................................... 16
Adjusting the projected image .............................................................................................................. 17
Connection .......................................................................................................................... 19
Connecting video source devices ......................................................................................................... 20
Connecting smart devices ...................................................................................................................... 21
Connecting a USB flash drive ................................................................................................................ 22
Operation ............................................................................................................................ 23
Starting up the projector ........................................................................................................................ 23
Using the menus ....................................................................................................................................... 24
Securing the projector ............................................................................................................................ 25
Switching input signal ............................................................................................................................... 26
Controlling the projector through a LAN environment ................................................................ 27
Using web control lock ........................................................................................................................... 27
Displaying image via QCast application through a LAN environment ........................................ 27
Presenting from a USB Reader ............................................................................................................. 27
Shutting down the projector ................................................................................................................. 29
Direct power off ...................................................................................................................................... 29
Menu operation ................................................................................................................... 30
Basic menu ............................................................................................................................................... 30
Advanced menu ..................................................................................................................................... 32
Maintenance ........................................................................................................................ 41
Care of the projector .............................................................................................................................. 41
Lamp information ..................................................................................................................................... 41
Troubleshooting ................................................................................................................. 47
Specifications ...................................................................................................................... 48
Projector specifications .......................................................................................................................... 48
Dimensions ................................................................................................................................................ 49
Timing chart............................................................................................................................................... 50
Table of Contents
3
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information technology
equipment. However, to ensure safe use of this product, it is important that you follow the instructions
mentioned in this manual and marked on the product.
1. Please read this manual before you
operate your projector. Save it for future
reference.
2. Do not look straight at the projector
lens during operation. The intense light
beam may damage your eyes.
3. Refer servicing to qualified service
personnel.
6. In some countries, the line voltage is NOT
stable. This projector is designed to operate
safely within a mains voltage between 100 to
240 volts AC, but could fail if power cuts or
surges of ±10 volts occur. In areas where
the mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a power
stabilizer, surge protector or
uninterruptible power supply (UPS).
7. Do not block the projection lens with any
objects when the projector is under
operation as this could cause the objects to
become heated and deformed or even cause a
fire. To temporarily turn off the lamp, use the
blank function.
4. Always open the lens shutter (if any) or
remove the lens cap (if any) when the
projector lamp is on.
5. The lamp becomes extremely hot during
operation. Allow the projector to cool for
approximately 45 minutes prior to removing
the lamp assembly for replacement.
4
Important safety instructions
8. Do not operate lamps beyond the rated lamp
life. Excessive operation of lamps beyond the
rated life could cause them to break on rare
occasions.
13. Always place the projector on a level,
9. Never replace the lamp assembly or any
horizontal surface during operation.
electronic components unless the projector is
unplugged.
- Do not use if tilted at an angle of more than 10
degrees left to right, nor at angle of more than 15
degrees front to back. Using the projector when it is
not fully horizontal may cause a malfunction of, or
damage to, the lamp.
10. Do not place this product on an unstable cart,
stand, or table. The product may fall,
14. Do not stand the projector on end vertically.
sustaining serious damage.
Doing so may cause the projector to fall over,
causing injury or resulting in damage to the
projector.
11. Do not attempt to disassemble this projector.
There are dangerous high voltages inside
which may cause death if you should come
into contact with live parts. The only user
15. Do not step on the projector or place any
serviceable part is the lamp which has its own
objects upon it. Besides probable physical
removable cover.
damage to the projector, doing so may result
in accidents and possible injury.
Under no circumstances should you ever
undo or remove any other covers. Refer
servicing only to suitably qualified professional
service personnel.
12. Do not block the ventilation holes.
- Do not place this projector on a blanket, bedding or
any other soft surface.
- Do not cover this projector with a cloth or any other
item.
- Do not place inflammables near the projector.
16. When the projector is under operation, you
may sense some heated air and odor from its
ventilation grill. It is a normal phenomenon
and not a product defect.
If the ventilation holes are seriously
obstructed, overheating inside the projector
may result in a fire.
Important safety instructions
5
17. Do not place liquids near or on the projector. 20. Do not place this projector in any of the
Liquids spilled into the projector may cause it
following environments.
to fail. If the projector does become wet,
- Space that is poorly ventilated or confined. Allow at
least 50 cm clearance from walls and free flow of air
disconnect it from the power supply's power
around the projector.
outlet and call BenQ to have the projector
- Locations where temperatures may become
serviced.
excessively high, such as the inside of a car with all
windows rolled up.
- Locations where excessive humidity, dust, or cigarette
smoke may contaminate optical components, shorten
the projector's life span and darken the image.
18. This product is capable of displaying inverted
images for ceiling/wall mount installation.
19. This apparatus must be earthed.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C /
104°F
- Locations where the altitudes are higher than 3000 m
(10000 feet).
3000 m
(10000 feet)
0m
(0 feet)
Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
6
Important safety instructions
Introduction
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these items are missing,
please contact your place of purchase.
Standard accessories
Digital
Quick Projector
Start
Guide
Projector
Remote control with
batteries
User manual CD
Warranty card*
Power cord
VGA cable
Quick start guide
• The supplied accessories will be suitable for your region, and may differ from those illustrated.
• *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.
Optional accessories
1. Spare lamp kit
2. 3D glasses
3. Wireless Dongle: WDRT8192 USB Dongle,
QCast (QP01),QCast mirror (QP20)
4. Dust filter
Replacing the remote control batteries
1. Press and slide off the battery cover, as illustrated.
2. Remove the old batteries (if applicable) and install two
AAA batteries. Make sure that the positive and negative
ends are positioned correctly, as illustrated.
3. Slide the battery cover in until it clicks into place.
• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen,
bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for
your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the
batteries to avoid damage to the remote control from possible battery leakage.
Introduction
7
Projector exterior view
7
1
8
2
9
4
3
4
10
5
4
11
12
13
14
15
16
17
19
18
6
22
20
21
22
22
4
1. Focus ring
12. USB Type A port (for USB wireless dongle)
2. Vent (air exhaust)
13. HDMI/MHL-input port
3. Projection lens
4. Adjuster feet
14. USB Type A port (for USB flash drive / power
for HDMI dongle)
5. Lens cap
15. RGB (PC) signal input jacks
6. IR remote sensor
16. RGB (PC) signal output jack
7. External control panel
(See Controls and functions on page 9.)
17. RS-232 control port
8. Lamp cover
19. RJ-45 LAN input jack
9. Vent (air inlet)
20. AC power jack
10. Audio input jacks
Audio output jack
21. Kensington anti-theft lock slot
11. HDMI input port
8
Introduction
18. USB Mini-B port
22. Ceiling mount holes
Controls and functions
Projector & Remote control
• All the key presses described in this
document are available on the remote control
or projector.
1
• The remote control is without laser pointer
in Japan
1
2
5
6
7
3
4
8
9
10
6
11
5
8
10
4
12
9
18
7
13
14
15
16
17
1.
INFO
5. Arrow keys ( ,
POWER
Toggles the projector between standby mode
and on.
ON/
19
20
21
22
Off
Toggles the projector between standby mode
and on.
2. POWER indicator light/TEMPerature
warning light/LAMP indicator light
(See Indicators on page 46.)
,
,
)
When the On-Screen Display (OSD) menu is
activated, these keys are used as directional
arrows to select the desired menu items and
to make adjustments.
Keystone keys (
,
)
Displays the keystone correction page.
Volume keys
/
Decreases or increase the projector volume.
3. IR remote sensor
4. BACK
Goes back to previous OSD menu, exits and
saves menu settings.
Introduction
9
6. SOURCE
Displays the source selection bar.
7. ECO BLANK
Used to hide the screen picture.
Do not block the projection lens from
projecting as this could cause the blocking
object to become heated and deformed or
even cause a fire.
8. OK
Confirms the selected On-Screen Display
(OSD) menu item.
9. AUTO
16. PAGE /PAGE
Operate your display software program (on a
connected PC) which responds to page
up/down commands (like Microsoft
PowerPoint).
17. INFO
Displays the projector information.
18. FREEZE
Freezes the projected image.
19. ASPECT
Selects the display aspect ratio.
20. MODE
Automatically determines the best picture
timings for the displayed image when PC signal
Selects an available picture setup mode.
(analog RGB) is selected.
21. SMART ECO
10. MENU
Displays the Lamp Mode menu for selecting
Turns on the On-Screen Display (OSD) menu.
11. Source selection buttons: PC 1, VIDEO,
HDMI 1, MHL/HDMI 2, NETWORK
Selects an input source for display.
a suitable lamp operating mode.
22. QUICK INSTALL
Quickly selects several functions to adjust the
projected image and displays the test pattern.
Operating the LASER pointer
12.
The Laser Pointer is a presentation
aid for professionals. It emits red
13. MHL control buttons
colored light when you press it. The
( Previous,
Play/Pause, Next,
laser beam is visible. It is necessary to
Rewind,
Stop, Fast-forward)
press and hold LASER for
Goes to the previous file/Plays/Pauses/Goes to continuous output.
the next file/Rewinds/Stops/Fast-forwards
The laser pointer is not a toy. Parents
during media playback.
should be mindful of the dangers of
Only available when controlling your smart
laser energy and keep this remote
device in MHL mode.
control out of the reach of children.
Toggles projector audio between on and off.
14. LASER
Emits visible laser pointer light for
presentation purposes.
15. ZOOM+/ZOOMMagnifies or reduces the projected picture
size.
10
Introduction
Do not look into the laser light window or shine
the laser light beam on yourself or others. See the
warning messages on the back of the remote
control prior to using it.
Controlling your smart device with the remote control
When the projector projects the content
from your MHL compatible smart device,
you can use the remote control to
control your smart device.
To enter the MHL mode, press and hold
AUTO for 3 seconds. The following
buttons are available for controlling your
smart device: Arrow keys ( , , ,
), MENU, BACK, OK, MHL
control buttons.
To leave the MHL mode, press and hold
AUTO for 3 seconds.
When the projector is under MHL mode, the keypad on the projector should be with the same definition of the
keys on the remote control.
Remote control effective range
The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR
remote control sensor(s) to function correctly. The distance between the remote control and the
sensor(s) should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensor(s) on the
projector that might obstruct the infra-red beam.
• Operating the projector from the front
• Operating the projector from the top
Ap
Ap
pr
ox.
+ 30
pro
x. +
30º
º
Introduction
11
Positioning your projector
Choosing a location
Before choosing an installation location for your projector, take the following factors into consideration:
• Size and position of your screen
• Electrical outlet location
• Location and distance between the projector and the rest of your equipment
You can install your projector in the following ways.
1. Front Table
2. Rear Table
Select this location with the projector placed on
the table in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
Select this location with the projector placed on
the table behind the screen. Note that a special
rear projection screen is required.
3. Front Ceiling
4. Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the
screen. Purchase the BenQ Projector Ceiling
Mount Kit from your dealer to mount your
projector on the ceiling.
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
BenQ Projector Ceiling Mount Kit are required
for this installation location.
After turning on the projector, go to Advanced Menu - Settings > Projector Installation >
Projector Installation and press / to select a setting.
You can also use QUICK INSTALL on the remote control to access this menu.
12
Positioning your projector
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting (if available), and the video format
each factors in the projected image size.
Projection dimensions
MX731
4:3 Screen diagonal
Screen
Center of lens
H
W
Offset
Projection distance
• The screen aspect ratio is 4:3 and the projected picture is in a 4:3 aspect ratio
Screen size
Diagonal
Projection distance (mm)
H (mm)
W (mm)
Min distance
(max. zoom)
Average
Max distance
Offset (mm)
Inch
mm
(min. zoom)
30
762
457
610
920
1061
1201
34
35
889
533
711
1074
1237
1401
40
40
1016
610
813
1227
1414
1601
46
50
1270
762
1016
1534
1768
2002
57
60
1524
914
1219
1841
2121
2402
69
70
1778
1067
1422
2148
2475
2802
80
80
2032
1219
1626
2455
2829
3202
91
90
2286
1372
1829
2761
3182
3603
103
100
2540
1524
2032
3068
3536
4003
114
110
2794
1676
2235
3375
3889
4403
126
120
3048
1829
2438
3682
4243
4804
137
130
3302
1981
2642
3989
4596
5204
149
140
3556
2134
2845
4296
4950
5604
160
150
3810
2286
3048
4602
5304
6005
171
160
4064
2438
3251
4909
5657
6405
183
170
4318
2591
3454
5216
6011
6805
194
180
4572
2743
3658
5523
6364
7205
206
200
5080
3048
4064
6137
7071
8006
229
250
6350
3810
5080
7671
8839
10008
286
300
7620
4572
6096
9205
10607
12009
343
For example, if you are using a 120-inch screen, the recommended projection distance is 4243 mm.
If your measured projection distance is 5000 mm, the closest match in the "Projection distance (mm)"
column is 4950 mm. Looking across this row shows that a 140'' (about 3.6 m) screen is required.
To optimize your projection quality, we suggest you do the projection within non-gray area.
Positioning your projector
13
All measurements are approximate and may vary from the actual sizes.
BenQ recommends that if you intend to permanently install the projector, you should physically test the projection
size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this
projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your
installation location.
MW732
16:10 Screen diagonal
Screen
Center of lens
H
Offset
W
Projection distance
• The screen aspect ratio is 16:10 and the projected picture is in a 16:10 aspect ratio
Screen size
Diagonal
Projection distance (mm)
Min distance
Offset (mm)
W (mm)
762
404
646
782
898
1014
40
35
889
471
754
912
1048
1184
47
40
1016
538
862
1042
1198
1353
54
50
1270
673
1077
1303
1497
1691
67
60
1524
808
1292
1564
1796
2029
81
70
1778
942
1508
1824
2096
2367
94
80
2032
1077
1723
2085
2395
2705
108
90
2286
1212
1939
2346
2695
3043
121
100
2540
1346
2154
2606
2994
3382
135
110
2794
1481
2369
2867
3293
3720
148
120
3048
1615
2585
3127
3593
4058
162
130
3302
1750
2800
3388
3892
4396
175
140
3556
1885
3015
3649
4192
4734
188
150
3810
2019
3231
3909
4491
5072
202
160
4064
2154
3446
4170
4790
5411
215
170
4318
2289
3662
4431
5090
5749
229
180
4572
2423
3877
4691
5389
6087
242
200
5080
2692
4308
5212
5988
6763
269
250
6350
3365
5385
6516
7485
8454
337
300
7620
4039
6462
7819
8982
10145
404
mm
30
(max. zoom)
Average
Max distance
H (mm)
Inch
(min. zoom)
For example, if you are using a 120-inch screen, the recommended projection distance is 3593 mm.
If your measured projection distance is 5000 mm, the closest match in the "Projection distance (mm)"
column is 5090 mm. Looking across this row shows that a 170'' (about 4.3 m) screen is required.
To optimize your projection quality, we suggest you do the projection within non-gray area.
14
Positioning your projector
All measurements are approximate and may vary from the actual sizes.
BenQ recommends that if you intend to permanently install the projector, you should physically test the projection
size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this
projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your
installation location.
MH733
16:9 Screen diagonal
Screen
Center of lens
H
Offset
W
Projection distance
• The screen aspect ratio is 16:9 and the projected picture is in a 16:9 aspect ratio
Screen size
Diagonal
Projection distance (mm)
Min distance
Offset (mm)
W (mm)
762
374
664
764
880
996
19
35
889
436
775
891
1027
1162
22
40
1016
498
886
1018
1173
1328
25
50
1270
623
1107
1273
1467
1660
31
60
1524
747
1328
1528
1760
1992
37
70
1778
872
1550
1782
2053
2324
44
80
2032
996
1771
2037
2347
2657
50
90
2286
1121
1992
2291
2640
2989
56
100
2540
1245
2214
2546
2933
3321
62
110
2794
1370
2435
2800
3227
3653
68
120
3048
1494
2657
3055
3520
3985
75
130
3302
1619
2878
3310
3813
4317
81
140
3556
1743
3099
3564
4107
4649
87
150
3810
1868
3321
3819
4400
4981
93
160
4064
1992
3542
4073
4693
5313
100
170
4318
2117
3763
4328
4987
5645
106
180
4572
2241
3985
4583
5280
5977
112
200
5080
2491
4428
5092
5867
6641
125
250
6350
3113
5535
6365
7333
8302
156
300
7620
3736
6641
7638
8800
9962
187
mm
30
(max. zoom)
Average
Max distance
H (mm)
Inch
(min. zoom)
For example, if you are using a 120-inch screen, the recommended projection distance is 3520 mm.
If your measured projection distance is 5000 mm, the closest match in the "Projection distance (mm)"
column is 4987 mm. Looking across this row shows that a 170'' (about 4.3 m) screen is required.
To optimize your projection quality, we suggest you do the projection within non-gray area.
Positioning your projector
15
All measurements are approximate and may vary from the actual sizes.
BenQ recommends that if you intend to permanently install the projector, you should physically test the projection
size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this
projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your
installation location.
Mounting the projector
If you intend to mount your projector, we strongly recommend that you use a proper fitting BenQ
projector mounting kit and that you ensure it is securely and safely installed.
If you use a non-BenQ brand projector mounting kit, there is a safety risk that the projector may fall
down due to an improper attachment through the use of the wrong gauge or length screws.
Before mounting the projector
• Purchase a BenQ projector mounting kit from the place you purchased your BenQ projector.
• BenQ recommends that you also purchase a separate Kensington lock compatible security cable and
attach it securely to both the Kensington lock slot on the projector and the base of the mounting
bracket. This will perform the secondary role of restraining the projector should its attachment to the
mounting bracket become loose.
• Ask your dealer to install the projector for you. Installing the projector on your own may cause it to
fall and result in injury.
• Take necessary procedures to prevent the projector from falling off such as during an earthquake.
• The warranty doesn’t cover any product damage caused by mounting the projector with a non-BenQ
brand projector mounting kit.
• Consider the surrounding temperature where the projector is ceiling/wall mounted. If a heater is used,
the temperature around the ceiling may be higher than expected.
• Read the user manual for the mounting kit about the range of torque. Tightening with torque
exceeding the recommended range may cause damage to the projector and subsequently falling off.
• Make sure the power outlet is at an accessible height so that you can easily shut down the projector.
Ceiling/Wall mount installation diagram
100
75
27
Ceiling/Wall mount screw: M4
(Max L = 25 mm; Min L = 20 mm)
146
16
Positioning your projector
75
Unit: mm
Adjusting the projected image
Adjusting the projection angle
If the projector is not placed on a flat surface or the
screen and the projector are not perpendicular to
each other, the projected image becomes
trapezoidal. You can screw the adjuster feet to
fine-tune the horizontal angle.
To retract the feet, screw the adjuster feet in a
reverse direction.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO. Within 3
seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and
Clock to provide the best picture quality.
The current source information will be displayed in the corner of the screen for 3 seconds.
This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image size and clarity
Adjust the projected image to the size that you
need using the zoom ring.
Sharpen the image by rotating the focus ring.
Correcting keystone
This function is not available when there is no input signal. If you wish to use this function when there is no input
signal, activate Test Pattern first.
Keystoning refers to the situation where the projected image becomes a trapezoid due to angled
projection.
To correct this, you will need to manually correct it following these steps.
Positioning your projector
17
1. Do one of the following steps to display the keystone
correction page.
• Press /
on the projector or remote control.
Press
.
Press
.
• Press QUICK INSTALL on the remote control. Press to
highlight 2D Keystone and press OK.
• Go to Advanced Menu - Display > 2D Keystone and
Press .
Press .
press OK.
2. After the 2D Keystone correction page displays. Press
to
correct keystoning at the top of the image. Press
to correct keystoning at the bottom of the
image. Press on the projector to correct keystoning at the right side of the image. Press
the projector to correct keystoning at the left side of the image.
on
3. When 2D Keystone correction page displays, you can also do the following settings:
• Press AUTO to reset the keystone values.
• Press / to disable the auto vertical keystone function.
Auto Vertical Keystone function
• Go to Advanced Menu - Display > Auto Vertical Keystone and press OK to turn on the
auto vertical keystone function. The image keystoning is corrected automatically and the keystone
value displays.
• Press / to disable the function.
Adjusting Corner Fit
This function is not available when there is no input signal. If you wish to use this function when there is no input
signal, activate Test Pattern first.
You can manually adjust four corners of the image by setting the horizontal and vertical values.
1. Do one of the following steps to display the corner fit correction page.
• Press QUICK INSTALL on the remote control. Press to highlight Corner Fit and press
OK.
• Go to Advanced Menu - Display > Corner Fit and press OK.
2. Press
/ / /
3. Press
/
to adjust vertical values.
4. Press
/
to adjust horizontal values.
18
to select one corner and press OK.
Positioning your projector
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
A/V device
Monitor
Smart device
4
7
5
1
2
1
VGA cable
2
VGA to DVI-A cable
3
USB cable
4
Component Video to
VGA (D-Sub)
adapter cable
5
Audio cable
6
USB cable (A to micro
B type) connect
to HDMI dongle for
power supply
7
HDMI cable
8
HDMI dongle (QCast,
QCast Mirror, etc.)
9
USB Wireless dongle
10
USB flash drive
6
8
9
5
5
8
10
7
1
3
Speakers
Notebook or
desktop computer
• To ensure a stable power supply, do not connect both USB Type A ports simultaneously.
• The HDMI2/MHL and USB TYPE-A port cannot provide power supply simultaneously. The power output is
either through HDMI2/MHL or USB TYPE-A port. Note that the default power output is through the USB
TYPE-A port. When connecting to HDMI2/MHL port, set MHL Power Switch to On in the OSD menu to
ensure the dongle is powered, see MHL Power Switch on page 38. After that, when connecting to USB TYPE-A
port (including WIRELESS DONGLE), remember to set MHL Power Switch to Off in the OSD menu.
Connection
19
• In the connections above, some cables may not be included with the projector (see Shipping contents on page 7).
They are commercially available from electronics stores.
• The connection illustrations are for reference only. The rear connecting jacks available on the projector vary with
each projector model.
• Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo
like FN + function key with a monitor symbol turns the external display on/off. Press FN and the labeled function
key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.
• If the selected video image is not displayed after the projector is turned on and the correct video source has been
selected, check that the video source device is turned on and operating correctly. Also check that the signal cables
have been connected correctly.
Connecting video source devices
You need only connect the projector to a video source device using just one of the connecting methods,
however each provides a different level of video quality.
Terminal
Picture quality
HDMI
Best
HDMI2/MHL
Best
Component Video (through RGB
input)
Better
Connecting audio
The projector has built-in mono speaker(s) which are designed to provide basic audio functionality
accompanying data presentations for business purposes only. They are not designed for, nor intended
for stereo audio reproduction use as might be expected in home theater or home cinema applications.
Any stereo audio input (if provided), is mixed into a common mono audio output through the projector
speaker(s).
The built-in speaker(s) will be muted when the AUDIO OUT jack is connected.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected.
• If the selected video image is not displayed after the projector is turned on and the correct video source has been
selected, check that the video source device is turned on and operating correctly. Also check that the signal cables
have been connected correctly.
20
Connection
Connecting smart devices
The projector can project the content directly from a smart device by using a wireless dongle.
HDMI wireless dongle (e.g. BenQ QCastMirror, QCast)
• Connect the dongle to HDMI and USB TYPE-A ports on the projector and switch the input signal
to HDMI-1.
• Connect the dongle to HDMI2/MHL port on the projector and switch the input signal to
HDMI-2/MHL.
Set MHL Power Switch to On in the OSD menu to ensure the dongle is powered, see MHL Power Switch on page
38.
USB wireless dongle (e.g. WDRT8192 USB Dongle)
Connect the USB wireless dongle to WIRELESS DONGLE port on the projector and switch the
input signal to Network Display.
For details, see BenQ Network Projector Operation Guide, which can be downloaded from BenQ product webpage.
Connection
21
Connecting a USB flash drive
1. Plug the USB flash drive into the USB TYPE-A port of the projector.
2. A dialog is shown for quick source switching. Select Yes to enter USB Reader source. Or you
can manually select USB Reader from the source selection bar.
For details, see Presenting from a USB Reader on page 27.
22
Connection
Operation
Starting up the projector
1. Plug the power cord. Turn on the power outlet switch
(where fitted). The power indicator on the projector
lights orange after power has been applied.
2. Press
on the projector or
on the remote
control to start the projector. The power indicator
flashes green and stays green when the projector is on.
The start up procedure takes about 30 seconds. In the
later stage of start up, a startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image
clearness.
3. If the projector is activated for the first time, select your
OSD language following the on-screen instructions.
4. If you are prompted for a password, press the arrow keys
to enter a 6-digit password. See Utilizing the password
function on page 25.
5. Switch all of the connected equipment on.
6. The projector will search for input signals. The current
input signal being scanned appears. If the projector does
not detect a valid signal, the message “No Signal” will
continue displaying until an input signal is found.
You can also press SOURCE to select your desired input signal. See Switching input signal on page
26.
• Please use the original accessories (e.g. power cord) to avoid possible dangers such as electric shock and fire.
• If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before
energizing the lamp.
• The Setup Wizard screenshots are for reference only and may differ from the actual design.
• If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message
“Out of Range” displayed on the background screen. Please change to an input signal which is compatible with
the projector's resolution or set the input signal to a lower setting. See Timing chart on page 50.
• If no signal is detected for 3 minutes, the projector automatically enters saving mode.
Operation
23
Using the menus
The projector is equipped with 2 types of On-Screen Display (OSD) menus for making various
adjustments and settings.
• Basic OSD menu: provides primary menu functions. (See Basic menu on page 30)
• Advanced OSD menu: provides full menu functions. (See Advanced menu on page 32)
To access the OSD menu, press MENU on the projector or remote control.
• Use the arrow keys ( / / / ) on the projector or remote control to move through the menu items.
• Use OK on the projector or remote control to confirm the selected menu item.
The first time you use the projector (after finishing the initial setup), Basic OSD menu displays.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the Basic OSD menu.
Basic Menu
1
1
Menu Type
4
Press OK to enter
the menu.
2
Main menu
5
Status
3
Current input
signal
6
Press MENU to go
to the previous page
or to exit.
Lamp Mode
Brightness
SmartEco
Aspect Ratio
Wireless LAN
Auto
2
2
Information
Picture Mode
Presentation
Menu Type
Volume
Enter
3
6
Exit
4
5
If you intend to switch from the Basic OSD menu to the Advanced OSD menu, follow the
instructions below:
1. Go to Basic Menu > Menu Type.
2. Press OK and press / to select Advanced. Next time when you turn on the projector, you
may access the Advanced OSD menu by pressing MENU.
Below is the overview of the Advanced OSD menu.
1
Main menu
& Main
menu icon
5
2
Sub-menu
6
3
Current
input signal
7
4
Press OK
to enter the
menu.
2
Picture
Picture Mode
Presentation
Reference Mode
Presentation
Brightness
Display
Contrast
7
Color
Network
Tint
1
Sharpness
Settings
Brilliant Color
Advanced Color Settings
System
Information
Reset Picture
Return
Enter
3
24
4
Operation
Off
5
Exit
6
Press BACK to go
to the previous
page.
Press MENU to
go to the previous
page or to exit.
Status
Likewise, when you wish to switch from the Advanced OSD menu to the Basic OSD menu, follow
the instructions below:
1. Go to Advanced Menu - System > Menu Settings and press OK.
2. Select Menu Type and OK.
3. Press / to select Basic. Next time when you turn on the projector, you may access the Basic
OSD menu by pressing MENU.
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as
the Kensington lock, to secure the projector. You can locate a Kensington lock slot on the rear side of
the projector. See item 21 on page 8.
A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the lock’s
documentation for finding out how to use it.
Utilizing the password function
Setting a password
1. Go to Advanced Menu - Settings > Security Settings. Press OK. The Security Settings
page appears.
2. Highlight Change Password and press OK.
3. The four arrow keys ( , , , ) respectively represent
4 digits (1, 2, 3, 4). According to the password you desire
to set, press the arrow keys to enter six digits for the
password.
4. Confirm the new password by re-entering the new
password.
Once the password is set, the OSD menu returns to the
Security Settings page.
Input New Password
Return
5. To activate the Power On Lock function, press / to
highlight Power On Lock and press / to select On. Input the password again.
• The digits being input will display as asterisks on-screen. Make a note of your selected password and keep it in a
safe place in advance or right after the password is entered so that it is available to you should you ever forget it.
• Once a password has been set and the power on lock is activated, the projector cannot be used unless the
correct password is entered every time the projector is started.
If you forget the password
If you enter the wrong password, the password error
message will appear, and the Input Current Password
message follows. If you absolutely do not remember the
password, you can use the password recall procedure. See
Entering the password recall procedure on page 26.
Password Error
Please try again.
If you enter an incorrect password 5 times in succession, the
projector will automatically shut down in a short time.
Operation
25
Entering the password recall procedure
1. Press and hold AUTO for 3 seconds. The projector will
display a coded number on the screen.
Recall Password
Please write down the recall code, and contact
BenQ Customer Center.
2. Write down the number and turn off your projector.
3. Seek help from the local BenQ service center to decode
the number. You may be required to provide proof of
purchase documentation to verify that you are an
authorized user of the projector.
Recall Code:
Return
Changing the password
1. Go to Advanced Menu - Settings > Security Settings > Change Password.
2. Press OK. The message “Input Current Password” appears.
3. Enter the old password.
• If the password is correct, another message “Input New Password” appears.
• If the password is incorrect, the password error message will appear, and the message “Input
Current Password” appears for your retry. You can press BACK to cancel the change or try
another password.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
Disabling the password function
To disable password protection, go to Advanced Menu - Settings > Security Settings > Power
On Lock and press / to select Off. The message “Input Current Password” appears. Enter the
current password.
• If the password is correct, the OSD menu returns to the Security Settings page. You will not
have to enter the password next time turning on the projector.
• If the password is incorrect, the password error message will appear, and the message “Input
Current Password” appears for your retry. You can press BACK to cancel the change or try
another password.
Though the password function is disabled, you need to keep the old password in hand should you ever need to
re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time.
However, it can only display one full screen at a time. When starting
up, the projector automatically searches for the available signals.
Be sure the Advanced Menu - Settings > Auto Source Search
menu is On if you want the projector to automatically search for the
signals.
To select the source:
1. Press SOURCE. A source selection bar appears.
2. Press
/
until your desired signal is selected and press OK.
Once detected, the selected source information will appear at the corner of the screen for seconds.
If there is multiple equipment connected to the projector, repeat steps 1-2 to search for another
signal.
26
Operation
• The brightness level of the projected image will change accordingly when you switch between different input
signals.
• For best display picture results, you should select and use an input signal which outputs at the projector’s native
resolution. Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting,
which may cause some image distortion or loss of picture clarity. See Aspect Ratio on page 30.
Controlling the projector through a LAN environment
You can remotely control the projector from a computer by using a Web browser when the computer
and the projector are properly connected to the same local area network. There are 2 ways of
connection: Wired connection and Wireless connection. Go to Advanced Menu - Network for
LAN settings.
Once the projector and your computer are on the same local area network, you can access “BenQ
Projector Control System” through Web browser and start to control the projector. See BenQ
Network Projector Operation Guide for more details.
BenQ Network Projector Operation Guide can be downloaded from BenQ product webpage.
Using web control lock
This function is designed to prevent unauthorized people from maliciously changing the projector
settings through Web browser.
Go to Advanced Menu - Settings > Security Settings > Web Control Lock, and press /
select On. Once enabled, it is required to enter the correct Account/ Password for changing the
projector settings through “BenQ Projector Control System” by a web browser.
to
For security reasons, the setting cannot be adjusted after it is set to On. The only way to disable it is enter “BenQ
Projector Control System” by a web browser and set Web Control Lock to Off.
Displaying image via QCast application through a LAN
environment
The QCast is an application running on the computer or your smart device. It helps to display your
content to the projector via a local network connection.See BenQ Network Projector Operation
Guide for more details.
BenQ Network Projector Operation Guide can be downloaded from BenQ product webpage.
Presenting from a USB Reader
This feature allows you to browse the image and document files stored on a USB flash drive connected
to the projector. It can eliminate the need for a computer source.
Supported file formats
• Photo
Image format
JPEG
Size limitation
8000 x 6000
Operation
27
• BMP resolution supports up to 1600x1200(3.2 seconds).
• JPEG progressive resolution supports up to 1600 x 120.
• BMP and JPEG progressive (SW decode) only show icon.
• Unsupported BMP and JPGE file will show unsupported icon.
• Document
Image format
Adobe PDF
MS Word
MS Excel
MS PowerPoint
Support version
PDF 1.3
PDF 1.4
PDF 1.5
PDF 1.6
Word 97, 2000, 2002, 2003.
Word 2007 (.docx), 2010 (.docx)
Excel 97, 2000, 2002, 2003.
Excel 2007 (.xlsx), 2010 (.xlsx).
British PowerPoint 97.
PowerPoint 2000, 2002, 2003.
PowerPoint 2007 (.pptx).
PowerPoint 2010 (.pptx),.
Size limitation
Up to 75MB
Up to 100MB
Up to 15MB
Up to 19MB
• MS Word does not support Bold Text in Simplified Chinese front.
• MS Excel does not support password-protected sheets.
• MS PowerPoint does not support SlideShow order.
Viewing the files
1. Plug the USB flash drive into the USB TYPE-A port of the projector.
2. A dialog is shown for quick source switching. Select Yes to enter USB Reader source.
3. Main menu will show up. Storages are classified as Photo and Document.
4. Choose Photo or Document and press OK to view files or folders.
5. Press / / /
to select and press OK to enter the subfolder or display a file.
6. After a file is displayed, press OK to call out the function bar. You can press
function and press OK to enact the selected item in the function bar.
/
select the
The storage limit on the USB flash drive is 64GB.
• Function bar for viewing photos
Shows the information of photo size, name and type
Rotates the file 90 degrees counterclockwise
Rotates the file 90 degrees clockwise
Starts the slideshow
Zooms in/out the file for details
Navigates the file after it is magnified
28
Operation
Reloads the file
• Function bar for viewing documents
Fits the width/height of the page with the screen
Zooms in/out the file for details
Navigates the file after it is magnified
Shutting down the projector
1. Press
on the projector or
on the remote
control and a confirmation message will appear
prompting you. If you don't respond in a few seconds, the
message will disappear.
2. Press
or
a second time. The power indicator
flashes orange, the projection lamp shuts down, and the
fans will continue to run for approximately 90 seconds to
cool down the projector.
3. Once the cooling process finishes, the power indicator
becomes a steady orange and fans stop. Disconnect the
power cord from the power outlet.
• To protect the lamp, the projector will not respond to any commands during the cooling process.
• To shorten the cooling time, you can also activate the Quick cooling function. See Quick Cooling on page 36.
• Avoid turning on the projector immediately after turning it off as excessive heat may shorten lamp life.
• Lamp life results will vary depending on environmental conditions and usage.
Direct power off
The AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait
about 10 minutes before re-starting the projector. If you attempt to re-start the projector, the fans may
run for a few minutes to cool down. In such cases, press
the fans stop and the power indicator turns orange.
or
again to start the projector after
Operation
29
Menu operation
Please note that the on-screen display (OSD) menus vary according to the signal type selected and the
projector model you are using.
The menu items are available when the projector detects at least one valid signal. If there is no
equipment connected to the projector or no signal detected, limited menu items are accessible.
Basic menu
Brightness
The higher the value, the brighter the image. Adjust this control so the black areas
of the image appear just as black and that detail in the dark areas is visible.
There are several options to set the image's aspect ratio depending on your input
signal source.
• Auto: Scales an image
proportionally to fit the
projector's native resolution in its
horizontal or vertical width.
Aspect Ratio
• Real: Projects an image as its
original resolution and resizes it to
fit within the display area. For
input signals with lower
resolutions, the projected image
will be displayed in its original size.
• 4:3: Scales an image so that it is
displayed in the center of the
screen with a 4:3 aspect ratio.
• 16:9: Scales an image so that it is
displayed in the center of the
screen with a 16:9 aspect ratio.
• 16:10: Scales an image so that it is
displayed in the center of the
screen with a 16:10 aspect ratio.
30
Menu operation
(MX731)
16:9 picture
4:3 picture
16:9 picture
4:3 picture
16:9 picture
16:10 picture
(MW732)
(MH733)
The projector is preset with several predefined picture modes so that you can
choose one to suit your operating environment and input signal picture type.
• Bright: Maximizes the brightness of the projected image. This mode is suitable for
environments where extra-high brightness is required, such as using the projector
in well lit rooms.
• Presentation: Is designed for presentations. The brightness is emphasized in this
mode to match PC and notebook coloring.
Picture Mode
• sRGB: Maximizes the purity of RGB colors to provide true-to-life images
regardless of brightness setting. It is most suitable for viewing photos taken with an
sRGB compatible and properly calibrated camera, and for viewing PC graphic and
drawing applications such as AutoCAD.
• Infographic: Is perfect for presentations with the mixture of text and graphics
due to its high color brightness and better color gradation to see the details
clearly.
• 3D: Is appropriate for playing 3D images and 3D video clips.
• User 1/User 2: Recalls the settings customized based on the current available
picture modes. See Reference Mode on page 32.
Volume
Adjusts the sound level.
Lamp Mode
See Setting the Lamp Mode on page 42.
Wireless LAN
See BenQ Network Projector Operation Guide, which can be downloaded from
BenQ product webpage.
• Native Resolution: Shows the native resolution of the projector.
• Detected Resolution: Shows the native resolution of the input signal.
• Source: Shows the current signal source.
• Picture Mode: Shows the selected mode in the Picture menu.
Information
• Lamp Mode: Shows the selected mode in the Lamp Settings menu.
• 3D Format: Shows the current 3D mode.
• Color System: Shows input system format.
• Lamp Usage Time: Shows the number of hours the lamp has been used.
• Firmware Version: Shows the firmware version of your projector.
Menu Type
Switches to the Advanced OSD menu. See Using the menus on page 24.
Menu operation
31
Advanced menu
Picture
The projector is preset with several predefined picture modes so that you can
choose one to suit your operating environment and input signal picture type.
• Bright: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
• Presentation: Is designed for presentations. The brightness is emphasized in this
mode to match PC and notebook coloring.
Picture Mode
• sRGB: Maximizes the purity of RGB colors to provide true-to-life images
regardless of brightness setting. It is most suitable for viewing photos taken with
an sRGB compatible and properly calibrated camera, and for viewing PC graphic
and drawing applications such as AutoCAD.
• Infographic: Is perfect for presentations with the mixture of text and graphics
due to its high color brightness and better color gradation to see the details
clearly.
• 3D: Is appropriate for playing 3D images and 3D video clips.
• User 1/User 2: Recalls the settings customized based on the current available
picture modes. See Reference Mode on page 32.
There are 2 user-definable modes if the current available picture modes are not
suitable for your need. You can use one of the picture modes (except the User
1/User 2) as a starting point and customize the settings.
Reference
Mode
1. Go to Picture > Picture Mode.
2. Press
/
to select User 1 or User 2.
3. Press to highlight Reference Mode, and press
mode that is closest to your need.
/
to select a picture
4. Press to select a menu item to be changed and adjust the value. The
adjustments define the selected user mode.
Brightness
The higher the value, the brighter the image. Adjust this control so the black areas
of the image appear just as black and that detail in the dark areas is visible.
Contrast
The higher the value, the greater the contrast. Use this to set the peak white level
after you have previously adjusted the Brightness setting to suit your selected input
and viewing environment.
Color
Lower setting produces less saturated colors. If the setting is too high, colors on
the image will be overpowering, which makes the image unrealistic.
Sharpness
The higher the value, the sharper the picture becomes.
This feature utilizes a new color-processing algorithm and system level
enhancements to enable higher brightness while providing truer, more vibrant
colors in picture. It enables a greater than 50% brightness increase in mid-tone
Brilliant Color images, which are common in video and natural scenes, so the projector
reproduces images in realistic and true colors. If you prefer images with that quality,
select On.
When Off is selected, the Color Temperature function is not available.
32
Menu operation
Color Temperature
There are several preset color temperature settings available. The available settings
may vary according to the signal type selected.
• Normal: Maintains normal colorings for white.
• Cool: Makes images appear bluish white.
• Warm: Makes images appear reddish white.
Color Temperature Tuning
You can also set a preferred color temperature by adjusting the following options.
• R Gain/G Gain/B Gain: Adjusts the contrast levels of Red, Green, and Blue.
• R Offset/G Offset/B Offset: Adjusts the brightness levels of Red, Green,
and Blue.
Color Management
This function provides six sets (RGBCMY) of colors to be adjusted. When you
select each color, you can independently adjust its range and saturation according
to your preference.
Advanced
Color Settings
• Primary Color: Selects a color from among R (Red), G (Green), B (Blue), C
(Cyan), M (Magenta), or Y (Yellow).
• Hue: Increase in the range will include colors
consisted of more proportions of its two
Yellow
adjacent colors. Please refer to the illustration
RED
GREEN
for how the colors relate to each other.
For example, if you select Red and set its range
at 0, only pure red in the projected picture will
Cyan
Magenta
be selected. Increasing its range will include red
BLUE
close to yellow and red close to magenta.
• Saturation: Adjusts the values to your
preference. Every adjustment made will reflect to
the image immediately. For example, if you select Red and set its value at 0,
only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less saturated
colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that
color will be overpowering and unrealistic.
• Gain: Adjusts the values to your preference. The contrast level of the
primary color you select will be affected. Every adjustment made will reflect to
the image immediately.
Wall Color
Corrects the projected picture’s color when the projection surface such as a
Advanced
painted wall which may not be white, the Wall Color feature can help correct the
Color Settings projected picture’s colors to prevent possible color difference between the source
and projected pictures. There are several precalibrated colors to choose from:
Light Yellow, Pink, Light Green, Blue, and Blackboard.
Reset Picture
Returns all of the adjustments you’ve made for the Picture menu to the factory
preset values.
Menu operation
33
Display
There are several options to set the image's aspect ratio depending on your input
signal source.
• Auto: Scales an image
proportionally to fit the
projector's native resolution in its
horizontal or vertical width.
Aspect Ratio
(MX731)
(MW732)
(MH733)
16:9 picture
• Real: Projects an image as its
original resolution and resizes it to
4:3 picture
fit within the display area. For
input signals with lower
resolutions, the projected image
will be displayed in its original size. 16:9 picture
• 4:3: Scales an image so that it is
displayed in the center of the
screen with a 4:3 aspect ratio.
• 16:9: Scales an image so that it is
displayed in the center of the
screen with a 16:9 aspect ratio.
4:3 picture
16:9 picture
• 16:10: Scales an image so that it is
displayed in the center of the
screen with a 16:10 aspect ratio.
16:10 picture
2D Keystone
Auto Vertical
Keystone
See Correcting keystone on page 17.
Corner Fit
See Adjusting Corner Fit on page 18.
Adjusts the image size and focus and check that the
projected image is free from distortion.
Test Pattern
• Phase: Adjusts the clock phase to reduce image
distortion. This function is only available when a PC
signal (analog RGB) or YPbPr signal is selected.
PC &
Component
YPbPr Tuning • H. Size: Adjusts the horizontal width of the image.
This function is only available when a PC signal (analog RGB) is selected.
Position
34
Menu operation
Displays the position adjustment page. To move the projected image, use the
directional arrow keys. This function is only available when a PC signal (analog RGB)
is selected.
This projector features a 3D function which enables you to enjoy the 3D movies,
videos, and sporting events in a more realistic way by presenting the depth of the
images. You need to wear a pair of 3D glasses to view the 3D images.
• 3D Mode: The default setting is Off. If you want the projector to automatically
choose an appropriate 3D format when detecting 3D contents, select Auto. If the
projector cannot recognize the 3D format, press / to choose a 3D mode from
among Top Bottom, Frame Sequential, Frame Packing and Side by Side.
When 3D function is activated:
• The brightness level of the projected image will decrease.
• The following settings cannot be adjusted: Picture Mode, Reference Mode.
3D
• The 2D Keystone can only be adjusted within limited degrees.
• 3D Sync Invert: When you discover the inversion of the image depth, enable
this function to correct the problem.
• Apply 3D Settings: After the 3D settings are saved, you can decide if you would
like to apply them by choosing a set of 3D settings that you have saved. Once
applied, the projector will automatically play the incoming 3D contents if it
matches the 3D settings saved.
Only the set(s) of 3D settings with memorized data is available.
• Save 3D Settings: When you have successfully displayed the 3D contents after
making the appropriate adjustments, you can enable this function and choose a set
of 3D settings to memorize current 3D settings.
Selects a suitable color format to optimize display quality.
• Auto: Automatically selects a suitable color space and gray level for the incoming
HDMI signal.
HDMI Format • RGB Limited: Utilizes the Limited range RGB 16-235.
• RGB Full: Utilizes the Full range RGB 0-255.
• YUV Limited: Utilizes the Limited range YUV 16-235.
• YUV Full: Utilizes the Full range YUV 0-255.
Magnifies or reduces the projected image.
1. After the Zoom bar displays, press
desired size.
Digital Zoom
repeatedly to magnify the picture to a
2. To navigate the picture, press OK to switch to the panning mode and press the
directional arrows ( , , , ) on the projector or remote control to
navigate the picture.
3. To reduce size of the picture, press OK to switch back to the zoom in/out
function, and press AUTO to restore the picture to its original size. You can
also press repeatedly until it is restored to the original size.
The picture can only be navigated after it is magnified. You can further magnify the picture while
searching for details.
Menu operation
35
Reset Display
Returns all of the adjustments you’ve made for the Display menu to the factory
preset values.
Network
Wireless LAN See BenQ Network Projector Operation Guide, which can be downloaded from
BenQ product webpage.
Wired LAN
AMX Device
Discovery
MAC Address
(Wireless)
MAC Address
(Wired)
When this function is On, the projector can be detected by AMX controller.
Displays the mac address for this projector.
Settings
Projector
Installation
The projector can be installed on a ceiling or behind a screen, or with one or more
mirrors. See Choosing a location on page 12.
Remote
Receiver
Allows you to enable all the remote receivers or one specific remote receiver on
the projector.
• Allows the projector to automatically search for a signal.
Auto Source
Search
Auto Signal
Adjustment
The following signal source(s) will not be automatically detected by the projector, and you’ll have to
manually select it from the source selection bar: Network Display, USB Reader.
• On: Allows the projector to automatically determines the best picture timings for
the displayed image when PC signal (analog RGB) is selected and AUTO is
pressed.
• Off: The projector will not respond when AUTO is pressed.
• Lamp Mode: See Setting the Lamp Mode on page 42.
Lamp Settings • Reset Lamp Timer: See Resetting the lamp timer on page 45.
• Lamp Timer: Displays the number of hours the lamp has been used.
Quick Cooling:
Selecting On enables the function and projector cooling time will be shortened
from a normal 90-second duration to approximately 15 seconds.
Operation
Settings
36
Menu operation
Blank Timer
Sets the image blank time when there is no action taken on the blank screen, once
elapsed the image will return to the screen. If the preset time spans are not suitable
for your need, select Disable. No matter Blank Timer is activated or not, you
can press most of the keys on the projector or remote control to restore the
picture.
Reminder Message
Sets the reminder messages on or off.
High Altitude Mode
We recommend you use the High Altitude Mode when your environment is
between 1500 m –3000 m above sea level, and ambient temperature is between
0°C–30°C.
Operation under "High Altitude Mode" may cause a higher decibel operating
noise level because of increased fan speed necessary to improve overall system
cooling and performance.
If you use this projector under other extreme conditions excluding the above, it
may display auto shut-down symptoms, which is designed to protect your projector
from over-heating. In cases like this, you should switch to High Altitude mode to
solve these symptoms. However, this is not to state that this projector can operate
under any and all harsh or extreme conditions.
Operation
Settings
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient
temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on
under such a condition.
Power On/Off Settings
• Direct Power On: Allows the projector to turn on automatically once the
power is fed through the power cord.
• Signal Power On: Sets whether to turn the projector directly on without
pressing
POWER or
detects a VGA signal.
ON when the projector is in standby mode and
• Auto Power Off: Allows the projector to turn off automatically if no input signal
is detected after a set period of time to prevent unnecessary waste of lamp life.
• Power Off Timer: Sets the auto-shutdown timer.
Instant Restart
Allows you to restart the projector immediately within 90 seconds after turning it
off.
Menu operation
37
Panel Key Lock
With the control keys on the projector locked, you can prevent your projector
settings from being changed accidentally (by children, for example). When the
Panel Key Lock is on, no control keys on the projector will operate except
POWER.
To release panel key lock, press and hold (the right key) for 3 seconds on the
projector or turn this function off using the remote control.
Security
Settings
If you turn off the projector without disabling panel key lock, the projector will still be in locked
status the next time it is turned on.
Change Password
See Utilizing the password function on page 25.
Power On Lock
See Utilizing the password function on page 25.
Web Control Lock
See Using web control lock on page 27.
Baud Rate
Selects a baud rate that is identical with your computer’s so that you can connect
the projector using a suitable RS-232 cable and update or download the projector’s
firmware. This function is intended for qualified service personnel.
HDMI
Equalizer
Adjusts the equalizer gain settings for an HDMI signal. The higher the setting, the
stronger the gain value. If there are more than one HDMI port on the projector,
select the HDMI port first before adjusting the value.
MHL Power
Switch
Disables or enables 5V power output for HDMI2/MHL port. When selecting Off,
the projector provides 5V power through the USB TYPE-A port.
Reset Settings
Returns all of the adjustments you’ve made for the Settings menu to the factory
preset values.
38
Menu operation
System
Language
Sets the language for the On-Screen Display (OSD) menus.
• Network: Allows you to make following settings:
Enable Network
Standby Mode
Standby
Settings
Switch to Normal
Standby Mode
Allows the projector to provide the network function in
standby mode when Monitor Out or Audio Pass
Through is activated.
Allows the projector to disable the network function
after a set period of time after it enters standby mode.
For instance, if 20 min is selected, the projector is able to
provide the network function for 20 minutes after it
enters standby mode. When 20 minutes is up, the
projector enters normal standby mode.
• Monitor Out: Allows the projector to output a VGA signal when it is in standby
mode and the PC 1 jack and the MONITOR OUT jack are correctly connected
to devices.
• Audio Pass Through: The projector can play sound when it is in standby mode
and the corresponding jacks are correctly connected to devices. Press / to
choose the source that you wish to use. See Connection on page 19 for how to
make the connection.
Background
Settings
• Background: Sets the background color for the projector.
• Splash Screen: Allows you to select which logo screen will be displayed during
projector start-up.
• Menu Type: Switches to the Basic OSD menu.
Menu Settings • Menu Display Time: Sets the length of time the OSD will remain active after
your last key press.
• Mute: Temporarily turns off the sound.
• Volume: Adjusts the sound level.
Audio
Settings
• Power On/Off Ring Tone: Turns on or off the ring tone when the projector is
in startup and shutdown process.
The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power On/Off Ring Tone.
Returns all settings to the factory preset values.
Factory
Default
Reset System
The following settings will still remain: 2D Keystone, Auto Vertical Keystone, Corner Fit,
Wireless LAN, Wired LAN, Projector Installation, Lamp Timer, High Altitude Mode,
Security Settings, Baud Rate.
Returns all of the adjustments you’ve made for the System menu to the factory
preset values.
Menu operation
39
Information
• Native Resolution: Shows the native resolution of the projector.
• Detected Resolution: Shows the native resolution of the input signal.
• Source: Shows the current signal source.
• Picture Mode: Shows the selected mode in the Picture menu.
Information
• Lamp Mode: Shows the selected mode in the Lamp Settings menu.
• 3D Format: Shows the current 3D mode.
• Color System: Shows input system format.
• Lamp Usage Time: Shows the number of hours the lamp has been used.
• Firmware Version: Shows the firmware version of your projector.
40
Menu operation
Maintenance
Care of the projector
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. Please be sure to turn off the projector
and let it cool down completely before cleaning the lens.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently
wipe the lens surface.
• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as
alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with
rubber or vinyl materials may result in damage to the projector surface and cabinet material.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as described in
Shutting down the projector on page 29 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then
wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the recommended range for
the projector. Please refer to Specifications on page 48 or consult your dealer about the range.
• Retract the adjuster feet.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by
the built-in timer. The method of calculating the equivalent lamp hour is as follows:
Lamp Usage Time = (hours used in Normal mode) + (hours used in Economic mode) + (hours used
in SmartEco mode) + (hours used in LampSave mode)
Total (equivalent) lamp hour = 3.75 x (hours used in Normal mode) + 1.875 x (hours used in
Economic mode) + 1.875 x (hours used in SmartEco mode) + 1 x (hours used in LampSave mode)
Maintenance
41
To obtain the lamp hour information:
1. Go to Advanced Menu - Settings > Lamp Settings and press OK. The Lamp Settings page
appears.
2. Press
to select Lamp Timer and press OK. The Lamp Timer information is displayed.
You can also get the lamp hour information on the Information menu.
Extending lamp life
• Setting the Lamp Mode
Go to Advanced Menu - Settings > Lamp Settings > Lamp Mode and select a suitable lamp
power from among the provided modes.
Setting the projector in Economic, SmartEco or LampSave mode extends lamp life.
Lamp mode
Description
Normal
Economic
Provides full lamp brightness
Lowers brightness to extend the lamp life and decreases the fan noise
Adjusts the lamp power automatically depending on the content brightness level while
optimizing display quality
Adjusts the lamp power automatically depending on the content brightness level while
offering a longer lamp life
SmartEco
LampSave
• Setting Auto Power Off
This function allows the projector to turn off automatically if no input signal is detected after a set
period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go to Advanced Menu - Settings > Power On/Off Settings > Auto
Power Off and press / .
Timing of replacing the lamp
When the Lamp indicator lights up or a message appears suggesting it is time to replace the lamp,
please consult your dealer or go to http://www.BenQ.com before installing a new lamp. An old lamp
may cause a malfunction in the projector and in some instances the lamp may explode.
• The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected
input signal contrast/brightness settings, and is directly proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is
normal and expected behavior.
• The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn
the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning
the power back on, please contact your dealer. See Indicators on page 46.
The following Lamp warning displays will remind you to change the lamp.
Notice
Order a replacement lamp
Equivalent lamp hour >XXXX hours
Order a new lamp at www.BenQ.com
42
Maintenance
Install a new lamp for optimal performance. Press OK to
dismiss the message.
Notice
Replace lamp soon
Equivalent lamp hour >XXXX hours
Order a new lamp at www.BenQ.com
It is strongly recommended that you replace the lamp at this
age. The lamp is a consumable item. The lamp brightness
diminishes with use. This is normal lamp behavior. You can
replace the lamp whenever you notice that the brightness level
has significantly diminished.
Press OK to dismiss the message.
Notice
Replace lamp now
Equivalent lamp hour > XXXX Hours
Order a new lamp at www.BenQ.com
Notice
The lamp MUST be replaced before the projector will operate
normally.
Press OK to dismiss the message.
Out of lamp usage time
Replace lamp (refer to user manual)
then reset the lamp timer
Order a new lamp at www.BenQ.com
"XXXX" shown in the above messages are numbers that vary depending on different models.
Replacing the lamp
• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before
changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp
glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the
empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper
manner.
• To assure optimal performance from the projector, it is recommended that you purchase a qualified projector
lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that
no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by
fractured lamp.
• Ensure good ventilation when handling broken lamps. We recommend that you use respirators, safety glasses,
goggles or face shield and wear protective clothing such as gloves.
1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid
burns by waiting for approximately 45 minutes until the lamp has cooled.
2. Loosen the screw(s) that secure the lamp cover on the
side of the projector until the lamp cover loosens.
Maintenance
43
3. Remove the lamp cover from the projector.
• Do not turn the power on with the lamp cover open.
• Do not insert your fingers between the lamp and the
projector. The sharp edges inside the projector may cause
injuries
4. Disconnect the lamp connector.
5. Loosen the screw(s) that secure the inner lamp.
5
6
6. Lift the handle so that it stands up.
4
4
7. Use the handle to slowly pull the lamp out of the
projector.
• Pulling it too quickly may cause the lamp to break and scatter
broken glass in the projector.
• Do not place the lamp in locations where water might splash
on it, children can reach it, or near flammable materials.
• Do not insert your hands into the projector after the lamp is
removed. The sharp edges inside the projector may cause
injuries. If you touch the optical components inside, it could
cause color unevenness and distortion of the projected
images.
8. As shown in the figure, insert the new lamp. Align the
lamp connector and 2 sharp points with the projector
and push the lamp a bit into the locked position.
8
9. Insert the lamp connector.
9
8
10. Tighten the screw(s) that secures the lamp.
11. Ensure the handle is fully laid flat and locked in place.
• Loose screw may cause a bad connection, which could
result in malfunction.
• Do not over tighten the screw.
12. Replace the lamp cover on the projector.
44
Maintenance
10
11
13. Tighten the screw that secures the lamp cover.
• Loose screw may cause a bad connection, which could
result in malfunction.
• Do not over tighten the screw.
14. .Connect the power and restart the projector.
Resetting the lamp timer
15. After the startup logo, open the On-Screen Display
(OSD) menu. Go to Advanced Menu - Settings > Lamp Settings and press OK. The Lamp
Settings page appears. Highlight Reset Lamp Timer and press OK. A warning message is
displayed asking if you want to reset the lamp timer. Highlight Reset and press OK. The lamp time
will be reset to “0”.
Do not reset if the lamp is not new or replaced as this could cause damage.
Maintenance
45
Indicators
Light
Status & Description
Power events
Stand-by mode
Powering up
Normal operation
Normal power-down cooling
Download
CW start fail
Lamp events
Lamp error in normal operation
Lamp is not lit up
Lamp life exhausted
Thermal events
Fan 1 error (the actual fan speed is outside the desired speed)
Fan 2 error (the actual fan speed is outside the desired speed)
Fan 3 error (the actual fan speed is outside the desired speed)
Temperature 1 error (over limited temperature)
Thermal sensor 1 open error
Thermal sensor short error
Thermal IC #I 12C connection error
Thermal IC #2 12C connection error
Thermal break error
Ambient temperature above 40 ºC*
*The projector will initiate a self-security mechanism from full power stand-by mode to low power stand-by mode
when the environment temperature is over 40 degrees. Please note that the projector’s Wake On LAN function will
be limited. We suggest you to turn on the projector manually if needed.
: Off
46
Maintenance
: Orange On
: Green On
: Red On
: Orange Flashing
: Green Flashing
: Red Flashing
Troubleshooting
The projector does not turn on.
Cause
There is no power from the power cord.
Remedy
Plug the power cord into the AC power jack on the
projector, and plug the power cord into the power outlet. If
the power outlet has a switch, make sure that it is switched
on.
Attempting to turn the projector on again during
Wait until the cooling down process has completed.
the cooling process.
No picture
Cause
Remedy
The video source is not turned on or connected
correctly.
The projector is not correctly connected to the
input signal device.
The input signal has not been correctly selected.
The lens cover is still closed.
Turn the video source on and check that the signal cable is
connected correctly.
Check the connection.
Select the correct input signal with the SOURCE key.
Open the lens cover.
Blurred image
Cause
The projection lens is not correctly focused.
The projector and the screen are not aligned
properly.
The lens cover is still closed.
Remedy
Adjust the focus of the lens using the focus ring.
Adjust the projection angle and direction as well as the
height of the projector if necessary.
Open the lens cover.
Remote control does not work.
Cause
Remedy
The batteries are out of power.
Replace both of the batteries with new ones.
There is an obstacle between the remote control
Remove the obstacle.
and the projector.
You are too far away from the projector.
Stand within 8 meters (26 feet) of the projector.
The password is incorrect.
Cause
You do not remember the password.
Remedy
See Entering the password recall procedure on page 26.
Troubleshooting
47
Specifications
Projector specifications
All specifications are subject to change without notice.
Optical
Input terminals
Resolution
1024 x 768 XGA (MX731)
1280 x 800 WXGA (MW732)
1920 (H) x 1080 (V) (MH733)
Computer input
RGB input
D-Sub 15-pin (female) x 1
Display system
1-CHIP DMD
Lens
F = 2.59 ~ 2.87, f = 16.88 ~ 21.88 mm
Lamp
240 W lamp
Electrical
Power supply
AC100–240V, 3.5 A, 50–60 Hz (Automatic)
Power consumption
355 W (Max); < 0.5 W (Standby);
< 2 W (when the Network function in the Standby
Settings is on)
Mechanical
Weight
2.5 Kg + 100 g
Output terminals
RGB output
D-Sub 15-pin (female) x 1
Speaker
10 watt x 1
Audio signal output
PC audio jack x 1
Video signal input
SD/HDTV signal input
Analog - Component
(through RGB input)
Digital - HDMI x 1;
HDMI/MHL x 1
Audio signal input
Audio in
PC audio jack x 1
USB
Mini-B x 1
Type-A x 1 (optional for USB wireless dongle)
Type-A (power supply 5V /1A, optional for USB flash
drive)
Environmental Requirements
Operating temperature
0°C–40°C at sea level
Operating relative humidity
10%–90% (without condensation)
Operating altitude
0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with
High Altitude Mode on)
Storage temperature
-20°C–60°C at sea level
Control
Storage humidity
10%–90% RH (without condensation)
RS-232 serial control
9 pin x 1
Storage altitude
30°C@ 0~12,200m above sea level
LAN control
RJ45 x 1
Transporting
Original packing or equivalent is recommended
IR receiver x 2
Repairing
Please visit below website and choose your country to
find your service contact window.
http://www.benq.com/welcome
48
Specifications
Dimensions
296 mm (W) x 120 mm (H) x 221 mm (D)
296
221
120
Unit: mm
Specifications
49
Timing chart
Supported timing for PC input
Resolution
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1024 x 576
1024 x 600
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1400 x 1050
1440 x 900
1600 x 1200
1680 x 1050
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
Mode
VGA_60
VGA_72
VGA_75
VGA_85
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_120
(Reduce Blanking)
XGA_60
XGA_70
XGA_75
XGA_85
XGA_120 (Reduce
Blanking)
1152 x 864_75
BenQ
Notebook_timing
BenQ
Notebook_timing
1280 x 720_60
1280 x 768_60
WXGA_60
WXGA_75
WXGA_85
WXGA_120
(Reduce Blanking)
SXGA_60
SXGA_75
SXGA_85
1280 x 960_60
1280 x 960_85
1360 x 768_60
SXGA+_60
WXGA+_60
UXGA
1680 x 1050_60
MAC13
MAC16
MAC19
MAC21
Vertical
Frequency
(Hz)
Horizontal
Frequency
(kHz)
Pixel
Frequency
(MHz)
Supported 3D format
Frame
Top
Side by
Sequential Bottom
Side
59.940
72.809
75.000
85.008
70.087
60.317
72.188
75.000
85.061
31.469
37.861
37.500
43.269
31.469
37.879
48.077
46.875
53.674
25.175
31.500
31.500
36.000
28.3221
40.000
50.000
49.500
56.250
119.854
77.425
83.000
V
60.004
70.069
75.029
84.997
48.363
56.476
60.023
68.667
65.000
75.000
78.750
94.500
V
119.989
97.551
115.5
V
75
67.5
108
60.0
35.820
46.966
64.995
41.467
51.419
60
59.87
59.810
74.934
84.880
45.000
47.776
49.702
62.795
71.554
74.250
79.5
83.500
106.500
122.500
V
V
V
119.909
101.563
146.25
V
60.020
75.025
85.024
60.000
85.002
60.015
59.978
59.887
60.000
59.954
66.667
74.546
74.93
75.060
63.981
79.976
91.146
60.000
85.938
47.712
65.317
55.935
75.000
65.290
35.000
49.722
60.241
68.680
108.000
135.000
157.500
108.000
148.500
85.5
121.750
106.500
162.000
146.250
30.240
57.280
80.000
100.000
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is possible
that some timings cannot be chosen.
50
Specifications
Supported timing for HDMI (HDCP) input
• PC timings
Resolution
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 768
1024 x 576@60Hz
1024 x 600@65Hz
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1440 x 900
1400 x 1050
1600 x 1200
1680 x 1050
1920 x 1080@60Hz
1920 x 1200
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
Mode
VGA_60
VGA_72
VGA_75
VGA_85
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_120 (Reduce
Blanking)
XGA_60
XGA_70
XGA_75
XGA_85
XGA_120 (Reduce
Blanking)
1152 x 864_75
1280 x 768_60
BenQ Notebook
Timing
BenQ Notebook
Timing
1280 x 720_60
1280 x 768_60
WXGA_60
WXGA_75
WXGA_85
WXGA_120
(Reduce Blanking)
SXGA_60
SXGA_75
SXGA_85
1280 x 960_60
1280 x 960_85
1360 x 768_60
WXGA+_60
SXGA+_60
UXGA
1680 x 1050_60
1920 x 1080_60
1920 x 1200_60
(Reduce Blanking)
MAC13
MAC16
MAC19
MAC21
Vertical
Frequency
(Hz)
Horizontal
Pixel
Supported 3D format
Frequency Frequency
Frame
Top
Side by
(kHz)
(MHz)
Sequential Bottom
Side
59.940
72.809
75.000
85.008
70.087
60.317
72.188
75.000
85.061
31.469
37.861
37.500
43.269
31.469
37.879
48.077
46.875
53.674
25.175
31.500
31.500
36.000
28.3221
40.000
50.000
49.500
56.250
V
V
V
V
V
V
119.854
77.425
83.000
V
60.004
70.069
75.029
84.997
48.363
56.476
60.023
68.667
65.000
75.000
78.750
94.500
V
V
V
119.989
97.551
115.5
V
75
59.87
67.5
47.776
108
79.5
60.00
35.820
46.996
64.995
41.467
51.419
60
59.870
59.810
74.934
84.880
45.000
47.776
49.702
62.795
71.554
74.250
79.5
83.500
106.500
122.500
V
V
V
V
V
V
V
V
V
119.909
101.563
146.25
V
60.020
75.025
85.024
60.000
85.002
60.015
59.887
59.978
60.000
59.954
60
63.981
79.976
91.146
60.000
85.938
47.712
55.935
65.317
75.000
65.290
67.5
108.000
135.000
157.500
108
148.500
85.500
106.500
121.750
162.000
146.250
148.5
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
59.950
74.038
154.0000
V
V
66.667
74.546
75.020
75.06
35.000
49.722
60.241
68.68
30.240
57.280
80.000
100.00
The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is possible
that some timings cannot be chosen.
Specifications
51
• Video timings
Timing
Resolution
Vertical
Frequency
(Hz)
Horizontal
Frequency
(kHz)
Pixel
Frequency
(MHz)
480i
480p
576i
576p
720/50p
720/60p
1080/50i
1080/60i
1080/24P
1080/25P
1080/30P
1080/50P
1080/60P
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
59.94
59.94
50
50
50
60
50
60
24
25
30
50
60
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
27
28.13
33.75
56.25
67.5
27
27
27
27
74.25
74.25
74.25
74.25
74.25
74.25
74.25
148.5
148.5
Supported 3D format
Frame
Frame
Top
Side by
Sequential Packing Bottom
Side
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Supported timing for MHL input
Timing
Resolution
Vertical Frequency
(Hz)
Horizontal
Frequency (kHz)
Pixel Frequency
(MHz)
480i
480p
576i
576p
720/50p
720/60p
1080/24P
1080/25P
1080/30P
1080/50i
1080/60i
1080/50p
1080/60p
720 (1440) x 480
720 x 480
720 (1440) x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
59.94
59.94
50
50
50
60
24
25
30
50
60
50
60
15.73
31.47
15.63
31.25
37.5
45.00
27
28.13
33.75
28.13
33.75
56.25
67.5
27
27
27
27
74.25
74.25
74.25
74.25
74.25
74.25
74.25
148.5
148.5
Supported timing for Component-YPbPr input
Timing
Resolution
480i
480p
576i
576p
720/50p
720/60p
1080/50i
1080/60i
1080/24P
1080/25P
1080/30P
1080/50P
1080/60P
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
Vertical Frequency Horizontal Frequency Pixel Frequency
(Hz)
(kHz)
(MHz)
59.94
59.94
50
50
50
60
50
60
24
25
30
50
60
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
27
28.13
33.75
56.25
67.5
13.5
27
13.5
27
74.25
74.25
74.25
74.25
74.25
74.25
74.25
148.5
148.5
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.
52
Specifications
Supported 3D
format
Frame
Sequential
V
V
V
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement