Bayliner 2002 3055 Ciera Owner Manual

Bayliner 2002 3055 Ciera Owner Manual
Engine Serial Numbers
Port: ____________________________________________________________
Starboard: _______________________________________________________
Hull Identification Number:__________________________________________
Hull Identification Number
• The Hull Identification
Number (HIN) is located
on the starboard side of
the transom.
• Record the HIN (and the
engine serial numbers) in
the space provided above.
• Include the HIN with any
correspondence or orders.
HIN LOCATION
© 2003 Bayliner Technical Publications. All rights reserved.
No part of this publication may be reproduced, stored in any retrieval system, or transmitted in any form by any means, electronic, mechanical, photocopying,
recording or otherwise, without prior written permission of Bayliner.
Printed in the United States of America.
General Notes
The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, Bayliner assumes no liability resulting from errors or omissions in this document, or from the use of information contained herein.
Due to our commitment to product improvement, Bayliner reserves the right to make changes in the product design, specifications, and equipment at any time
without notice or obligation. Illustrations and/or photos may show optional equipment.
All Bayliner products meet or exceed USCG (Unites States Coast Guard) and/or NMMA (National Marine Manufacturer’s Association) construction standards.
Manufactured with 1,1,1 Trichloroethane, a substance which harms public health and environment during the manufacturing process by destroying ozone in the
upper atmosphere.
Proprietary Rights
This document discloses subject matter in which Bayliner has proprietary rights. The information and design disclosed herein were originated by and are the property of Bayliner. Neither receipt nor possession thereof confers or transfers any right to reproduce, copy, alter or disclose the document or any part thereof, any
information contained therein, or to construct boats or any item from it, except by written permission from or written agreement with Bayliner. This document is to
be returned upon request to Bayliner.
CONTENTS
1
Chapter 1: Welcome Aboard!
14
Chapter 3: Propulsion &
Related Systems
1
Dimensions and Tank Capacities
1
Layout View
14
Engine
1
Dealer Service
14
Engine Room Ventilation System
1
About Your Limited Warranty
15
Fire Suppression System (If Equipped)
2
Boating Experience
16
2
Engine & Accessories Guidelines
2
Engine & Accessories Literature
3
Safety Standards
3
Qualified Maintenance
4
Special Care For Moored Boats
4
Sacrificial Anodes (Zincs)
5
Carbon Monoxide (CO)
5
6
6
7
7
7
7
8
9
Facts about CO
Where and How CO Can Accumulate
How to Protect Yourself and Others From CO
Trip Checklist
Monthly Checklist
Annual Checklist
Carbon Monoxide Alarm System
More Information
Boat Lifting
10
Chapter 2: Locations
10
Exterior Views
10 Hull views
11 Deck Views
12 Helm
13
Component Locations
Fuel System
16
17
17
17
Diagrams
Fuel Fill and Vent
Fuel Filters
Anti-siphon Valve
18
Quick Oil Drain System
19
Chapter 4: Controls
19
Steering
19
Shift/Throttle
19
Power Trim and Tilt
20
Trim Tabs
21
Chapter 5: Navigation &
Communications Equipment
21
VHF Radio (If Equipped)
21
Compass
21
Depth Finder
22
Chapter 6: Plumbing
37
Chapter 10: Lights
22
Bilge Pumps
37
Care and Maintenance
23 Autofloat Switches
37
Navigation Lights
37
Interior & Exterior Lights
37
Spotlight (If Equipped)
38
Chapter 11: Heating & Air Conditioning
38
Air Conditioning System (If Equipped)
39
Chapter 12: Electrical System
24
Seawater Systems
24 Seacocks
24 Seawater Strainers
25
Freshwater System
26
26
27
27
28
Drain Systems
28
28
28
28
28
29
Freshwater System Winterization
Transom Shower
Water Heater
Winterizing the Water Heater
Deck Drains
Sink Drains
Shower Drains
Sump Box Cleaning
Sump System Winterization
40
Marine Head With Holding Tank
29 Electric Flush (If Equipped)
30 Macerator (If Equipped)
31
Chapter 7: Deck Equipment
31
Canvas
32
Windlass (If Equipped)
32
Cleats and Tow Eyes
33
Chapter 8: Appliances &
Entertainment Systems
33
Refrigerator
33
Electric Stove (If Equipped)
34
Alcohol/Electric Stove (If Equipped)
34
Audio & Visual Equipment
35
Chapter 9: Convertible Seats,
Beds, & Tables
35
Dinette/V-Berth
36
Cockpit
36 Cockpit Table/Sunlounge
12 Volt DC System
40
40
41
42
42
43
Batteries
Fuses and Circuit Breakers
Battery Switches
Alternator
Battery Charger
120 Volt AC System
44 Shore Power
46 Transfer Switch (If Equipped with Dual
Shore Power)
47
Generator (If Equipped)
49 Generator Use
50
Electrical Routings
50
51
52
53
54
55
56
57
Deck Electrical Harness
Windlass Electrical Harness (If Equipped)
Radar Wing Electrical Harness
Hull Electrical Harness
Battery System
120 Volt AC System
Bonding Harness
Wire Diagrams
57 Engine Electrical System
58 DC Electrical System
59 AC Electrical System
60
Important Records
61
Float Plan
Hazard Boxes & Symbols
The hazard boxes and symbols shown below are used throughout this Supplement to call attention to potentially
dangerous situations which could lead to either personal injury or product damage. Read ALL warnings carefully
and follow ALL safety instructions.
!
DANGER!
This box alerts you to immediate hazards which WILL cause severe personal injury or death if
the warning is ignored.
!
WARNING!
This box alerts you to hazards or unsafe practices which COULD result in severe personal
injury or death if the warning is ignored.
!
CAUTION!
This box alerts you to hazards or unsafe practices which COULD result in minor personal
injury or cause product or property damage if the warning is ignored.
NOTICE
This box calls attention to installation, operation or maintenance information, which is
important to proper operation but is not hazard related.
FIRE
HAZARD!
EXPLOSION
HAZARD!
FALLING
HAZARD!
NO OPEN
FLAME!
ROTATING
PROPELLER HAZARD!
ELECTRICAL
HAZARD!
HOT
HAZARD!
RUN BILGE BLOWERS
FOR 4 MINUTES!
CO POISONING
HAZARD!
305 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
This Owner’s Manual Supplement provides specific information about your boat that is not covered in the Cruiser &
Yacht Owner’s Manual. Please study the Cruiser & Yacht Owner’s Manual and this Supplement carefully. Keep the
Cruiser & Yacht Owner’s Manual and this Supplement on your boat in a secure, yet readily available place.
Dimensions and Tank Capacities
Overall
Bridge
Draft
Draft (Drive
Length Clearance Beam (Drive Up)
Down)
31' 6"
9' 7"
11'
1' 9"
Fuel Capacity
(gal.)
2' 9"
Freshwater
Waste Holding
Capacity (gal.) Tank Capacity (gal.)
148
35
30
Layout View
battery
board
sink
transom
gate
buddy
seat
k
sin
transom
boarding
platform
ladder
microwave AC/DC
sink
panel
stove
head
refer
shower refrig.
boarding
ladder
transom
stowage
master berth
steps
engine
hatch
dinette
helm
station
lounge
hanging
locker
Dealer Service
•
•
•
•
•
Ask your dealer to explain all systems before taking delivery of your boat.
Your dealer is your key to service.
Contact your dealer if you have any problems with your new boat.
If your dealer cannot help, call our customer service hotline: 360-435-8957 or send us a FAX: 360-403-4235.
Buy replacement parts from any authorized Bayliner dealer.
About Your Limited Warranty
• Bayliner offers a Limited Warranty on each new Bayliner purchased through an authorized Bayliner dealer.
• A copy of the Limited Warranty was included in your owner’s packet.
• If your dealer cannot help, call our customer service hotline: 360-435-8957 or send us a FAX: 360-403-4235.
1
Chapter 1: Welcome Aboard!
305 • Owner’s Manual Supplement
Boating Experience
!
WARNING!
CONTROL HAZARD!
A qualified operator must be in control of the boat at all times. DO NOT operate your boat
while under the influence of alcohol or drugs.
If this is your first boat or if you are changing to a type of boat you are not familiar with, for your own comfort and
safety, obtain handling and operating experience before assuming command of the boat.
Take one of the boating safety classes offered by the U.S. Power Squadrons or the U.S. Coast Guard Auxiliary. For
more course information, including dates and locations of upcoming classes, contact the organizations directly:
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
Outside the United States, your selling dealer, national sailing federation or local boat club can advise you of local
sea schools or competent instructors.
Engine & Accessories Guidelines
NOTICE
When storing your boat please refer to your engine’s operation and maintenance manuals.
• Your boat’s engines and accessories were selected to provide optimum performance and service.
• Installing different engines or other accessories may cause unwanted handling characteristics.
• Should you choose to install different engines or to add accessories that will affect the boat’s running trim, have an
experienced marine technician perform a safety inspection and handling test before operating your boat again.
Certain modifications to your boat can result in cancellation of your warranty protection. Always check with
your dealer before making any modifications to your boat.
Engine & Accessories Literature
• The engines and accessories installed on your boat come with their own operation and maintenance manuals.
• Read and understand these manuals before using the engines and accessories.
• Unless noted otherwise, all engine and accessory literature referred to in this Supplement is included in your
owner’s packet.
2
305 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Safety Standards
!
DANGER!
FALLING and ROTATING PROPELLER HAZARD!
NEVER allow anyone to ride on parts of the boat not designed for
such use.
• Sitting on seat backs, lounging on the forward deck, bow riding, gunwale riding or occupying the transom platform while underway is especially hazardous and will cause personal
injury or death.
!
DANGER!
ROTATING PROPELLER and CARBON MONOXIDE
POISONING HAZARD!
• NEVER allow anyone to occupy, or hang from, the
back deck or swim platform while the engine(s)
are running.
• Teak surfing, dragging, or water skiing within 20 feet
of a moving watercraft can be fatal.
!
DANGER!
PERSONAL SAFETY HAZARD!
ALWAYS secure the anchor and other loose objects before getting underway. The anchor and
other items that are not properly secured can come loose when the boat is moving and cause
personal injury or death.
• Your boat’s mechanical and electrical systems were designed to meet safety standards in effect at the time it
was built.
• Some of these standards were mandated by law, all of them were designed to insure your safety, and the safety of
other people, vessels and property.
In addition to this Owner’s Manual Supplement, please read the Cruiser & Yacht Owner’s Manual and all accessory
instructions for important safety standards and hazard information.
Qualified Maintenance
!
WARNING!
To maintain the integrity and safety of your boat, allow only qualified personnel to perform
maintenance on, or in any way modify: The steering system, propulsion system, engine control
system, fuel system, environmental control system, electrical system or navigational system.
• Failure to maintain your boat’s systems (listed in the warning above) as designed could violate the laws in your
jurisdiction and could expose you and other people to the danger of bodily injury or accidental death.
• Follow the instructions provided in the Cruiser & Yacht Owner’s Manual, this Owner’s Manual Supplement, the
engine owner’s manual and all accessory instruction sheets and manuals.
3
Chapter 1: Welcome Aboard!
305 • Owner’s Manual Supplement
Special Care For Moored Boats
NOTICE
• To help seal the hull bottom and reduce the possibility of gelcoat blistering on moored boats,
apply an epoxy barrier coating. The barrier coating should be covered with several coats of
anti-fouling paint.
• Many states regulate the chemical content of bottom paints in order to meet environmental
standards. Check with your local dealer about recommended bottom paints, and about the
laws in effect in your area.
• Whether moored in saltwater or freshwater, your boat will collect marine growth on its hull bottom.
• This will detract from the boat’s beauty, greatly affect its performance and may damage the gelcoat.
• Periodically haul the boat out of the water and scrub the hull bottom with a bristle brush and a solution of soap
and water.
Sacrificial Anodes (Zincs)
NOTICE
Do not paint between the zinc and the metal surface it contacts and do not paint over the zincs.
Your boat is equipped with sacrificial anodes (zincs) to protect underwater metal parts from excessive deterioration.
Check the zincs regularly and replace them if they have deteriorated more than 70%.
There are many factors that affect the rate at which the zincs deteriorate, including:
• Water temperature
• Salinity
• Water pollution
Stray electrical current from the boat or dock may cause complete deterioration in just a few weeks. If there is rapid
zinc deterioration, measure the electrolytic corrosion around your boat with a Corrosion Test Meter. If the zincs are
not bonded correctly, they will not provide protection.
4
305 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Carbon Monoxide (CO)
!
DANGER!
• Carbon monoxide gas (CO) is colorless, odorless, tasteless, and
extremely dangerous.
• All engines, generators, and fuel burning appliances produce CO
as exhaust.
• Prolonged exposure to low concentrations or very quick exposure to high
concentrations will cause BRAIN DAMAGE or DEATH.
• Teak surfing, dragging, or water skiing within 20 feet of a moving watercraft can be fatal.
Facts about CO
• CO poisoning causes a significant number of boating deaths each year.
• Called the "silent killer", CO is an extremely toxic, colorless, odorless and tasteless gas.
• CO can harm or even kill you inside or outside your boat.
• CO can affect you whether you’re underway, moored, or anchored.
• CO symptoms are similar to seasickness or alcohol intoxication.
• CO can make you sick in seconds. In high enough concentrations, even a few breaths can be fatal.
• Breathing CO blocks the ability of your blood to carry oxygen.
• The effects are cumulative, even low levels of exposure can result in injury or death.
Factors That Increase the Effects of CO Poisoning
• Age
• Smokers or people exposed to high concentrations of cigarette smoke
• Consumption of alcohol
• Lung disorders
• Heart problems
• Pregnancy
5
Chapter 1: Welcome Aboard!
305 • Owner’s Manual Supplement
Where and How CO Can Accumulate
Stationary Conditions That Increase CO Accumulations Include:
A. Using engine,
generator, or
other fuel burning device
when boat is
moored in a
confined space.
B. Mooring too close to another boat that is using its
engine, generator, or other fuel burning device.
To correct stationary situations A and/or B:
• Close all windows, portlights and hatches.
• If possible, move your boat away from source of CO.
Running Conditions That Increase CO Accumulations Include:
C. Running boat with trim angle of bow too high.
D. Running boat without through ventilation (station wagon effect).
To correct running situations C and/or D:
• Trim bow down.
• Open windows and canvas.
• When possible, run boat so that prevailing winds help dissipate exhaust.
How to Protect Yourself and Others From CO
• Know where and how CO may accumulate in and around your boat (see above).
• Maintain fresh air circulation throughout the boat at all times.
• Know where your engine and generator exhaust outlets are located and keep everyone away from these areas.
• Never sit on, or hang onto, the back deck or swim platform while the engine(s) are running.
• Never enter the areas under swim platforms where exhaust outlets are located.
• Although CO can be present without the smell of exhaust fumes, if exhaust fumes are detected on the boat, take
immediate action to dissipate these fumes.
• Treat symptoms of seasickness as possible CO poisoning. Get the person into fresh air immediately. Seek medical attention—unless you’re sure it’s not CO.
• Install and maintain CO alarms inside your boat. Do not ignore any alarm. Replace alarms as recommended by
the alarm manufacturer.
• Follow the checklists provided on the next page.
• Get a Vessel Safety Check.
For information on how to get a free VESSEL SAFETY CHECK, visit www.vesselsafetycheck.org or contact your
local U.S. Coast Guard Auxiliary or United States Power Squadrons®.
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
6
305 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Trip Checklist
❏ Make sure you know where the exhaust outlets are located on your boat.
❏ Educate all passengers about the symptoms of CO poisoning and where CO may accumulate.
❏ When docked, or rafted with another boat, be aware of exhaust emissions from the other boat.
❏ Confirm that water flows from the exhaust outlet when the engines and generator are started.
❏ Listen for any change in exhaust sound, which could indicate an exhaust component failure.
❏ Test the operation of each CO alarm by pressing the test button.
Monthly Checklist
❏ Make sure all exhaust clamps are in place and secure.
❏ Look for exhaust leaking from exhaust system components. Signs include rust and/or black streaking, water
leaks, or corroded or cracked fittings.
❏ Inspect rubber exhaust hoses for burned, cracked, or deteriorated sections. All rubber hoses should be pliable and
free of kinks.
Annual Checklist
Have a Qualified Marine Technician:
❏ Replace exhaust hoses if cracking, charring, or deterioration is found.
❏ Ensure that your engines and generators are properly tuned, and well maintained.
❏ Inspect each water pump impeller and the water pump housing. Replace if worn. Make sure cooling systems are
in working condition.
❏ Inspect all metallic exhaust components for cracking, rusting, leaking, or loosening. Make sure they check the
cylinder head gasket, exhaust manifold, water injection elbow, and the threaded adapter nipple between the manifold and the elbow.
❏ Clean, inspect, and confirm proper operation of the generator cooling water anti-siphon valve (if equipped).
Carbon Monoxide Alarm System
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
• The house battery switch must be in the On position for the CO Monitors
to work.
NOTICE
The stereo memory and CO monitor(s) place a small, but constant drain on the battery. If your
boat will be unattended for an extended amount of time, plug into shore power with the battery
charger turned On, or disconnect the battery if shore power is not an option.
• Do not disconnect the alarm system.
• Read and understand the manufacturer’s instructions for your CO alarm system. If you did not receive an instruction manual, call (800) 383-0269 and one will be mailed to you.
If your boat is not equipped with a carbon monoxide alarm, consider purchasing one from your dealer or marine
supply store.
7
Chapter 1: Welcome Aboard!
305 • Owner’s Manual Supplement
More Information
For more information about how you can prevent carbon monoxide poisoning on recreational boats and other ways to
boat more safely, contact:
United States Coast Guard
Office of Boating Safety (G-OPB-3)
2100 Second Street SW
Washington, DC 20593
www.uscgboating.org
1-800-368-5647
National Marine Manufacturers
Association (NMMA)
200 East Randolph Drive
Suite 5100
Chicago, IL 60601-9301
www.nmma.org
312-946-6200
American Boat & Yacht Council,
Inc. (ABYC)
3069 Solomon’s Island Road
Edgewater, MD 21037-1416
www.abycinc.org
410-956-1050
For information on how to get a free VESSEL SAFETY CHECK, visit www.vesselsafetycheck.org or contact your
local U.S. Coast Guard Auxiliary or United States Power Squadrons®.
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
8
305 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Boat Lifting
!
WARNING!
PERSONAL INJURY and /or PRODUCT or PROPERTY DAMAGE HAZARD!
• Lift slings may slip on the hull. Avoid serious injury or death by securing the slings together
before lifting.
!
WARNING!
PERSONAL INJURY and /or PRODUCT or PROPERTY DAMAGE HAZARD!
• NEVER Lift the boat using the bow and stern eyes.
!
CAUTION!
PRODUCT or PROPERTY DAMAGE HAZARD!
• When lifting any boat, always use a spreader bar. The spreader bar must be equal to the
width of the boat at the lifting point.
LIFTING SLING LABELS
(TYPICAL PORT & STARBOARD)
13' 6"
2'
REFERENCE
POINT
AFT SLING
POSITION
FORWARD
SLING POSITION
• Always follow the lift equipment’s instructions and requirements.
• If water is present in the bilge, pump or drain the water out of the bilge areas before lifting your boat. Water in the
bilge can shift and change the balance of the load.
• When lifting your boat, always position the lifting slings at the port and starboard sling label positions as shown in
the illustration above.
9
305 • Owner’s Manual Supplement
Chapter 2: Locations
Exterior Views
Hull views
AFT BILGE PUMP
DRAIN
WATER TANK
VENT
FUEL TANK
VENT
PORTLIGHTS (TYPICAL)
BOW EYE
STARBOARD HULLSIDE
COCKPIT
DRAIN
ICE TUB
DRAIN
ROPE LOCKER
DRAIN
AIR CONDITIONER
DRAIN (IF EQUIPPED)
HEAD SINK
DRAIN
SHOWER SUMP
PUMP DRAIN
WASTE TANK COCKPIT
DRAIN
VENT
PORT HULLSIDE
AIR CONDITIONER
SUMP PUMP DRAIN
(IF EQUIPPED)
GALLEY SINK
DRAIN
FORWARD BILGE
PUMP DRAIN
STEP
DRAIN
STERN EYES
(STRONG POINTS)
TRANSOM VIEW
TRIM TAB
TRIM TAB
MACERATOR
DISCHARGE
(IF EQUIPPED)
10
ZINC PLATE
BILGE DRAIN
PLUG
GENERATOR
EXHAUST
(IF EQUIPPED)
305 • Owner’s Manual Supplement
Chapter 2: Locations
Deck Views
WIPER
(IF EQUIPPED)
WIPER
VENTILATION
HATCHES
SHORE POWER
INLET(S)
BOW
HATCH
CLEAT
(STRONG POINT)
WINDLASS CONTROLS
(IF EQUIPPED)
WINDLASS
(IF EQUIPPED)
CLEAT
(STRONG POINT)
SPOT LIGHT
(IF EQUIPPED)
NAVIGATION
LIGHT
ANCHOR
ROLLER
NAVIGATION
CLEATS
LIGHT
(STRONG POINTS)
ANCHOR
LIGHT
HORN
COCKPIT
FAUCET
CLEAT
(STRONG POINT)
WATER FILL
DECK FITTING
GRAB
RAIL
BATTERY SWITCH
PANEL
WASTE PUMP-OUT
DECK FITTING
CLEAT
(STRONG POINT)
COURTESY
LIGHT
TRANSOM SHOWER
(IF EQUIPPED)
GRAB
RAILS
CLEAT
(STRONG POINT)
FUEL FILL
DECK FITTING
11
Chapter 2: Locations
305 • Owner’s Manual Supplement
Helm
NOTE: TYPICAL HELM LAYOUT SHOWN
ACTUAL LAYOUT MAY VARY DEPENDING
ON ENGINE AND ACCESSORY OPTIONS
TACHOMETER
DEPTH
GAUGE
TACHOMETER
SPEEDOMETER
VOLT
GAUGE
FUEL
GAUGE
OIL
GAUGE
VOLT
GAUGE
TEMP
GAUGE
TRIM
GAUGE
TEMP
GAUGE
TRIM
GAUGE
OIL
GAUGE
SWITCH
PANELS
COMPASS
HELM LAYOUT
SHIFTER/
THROTTLE
COURTESY
LIGHT
SPOTLIGHT
CONTROL
(IF EQUIPPED)
STEERING
WHEEL
TRIM TAB
SWITCHES
IGNITION
PANEL
VHF (IF EQUIPPED)
HELM
STORAGE
TUB
DC BREAKER PANEL
12
COURTESY
LIGHT
MACERATOR
SWITCHES
305 • Owner’s Manual Supplement
Chapter 2: Locations
Component Locations
12 Volt Accessory Outlet: At the helm in the storage tub.
Air Conditioner Seawater Pickup Seacock: In the engine compartment on the port side.
Air Conditioner Unit: Under the V-Berth bunk.
Batteries: On the port forward side of the engine compartment.
Battery Charger: In the aft berth utility compartment on the aft wall.
Battery Switch: In the cabinet under the cockpit sink.
Bilge pump - Aft: In the engine compartment.
Bilge pump - Forward: Under the entry steps.
Carbon Monoxide Detector: In the salon on the aft starboard wall.
DC Circuit Breakers: At the helm under the dash panel.
Depth Sounder Transducer: In the engine compartment.
Engine Circuit Breakers: On the engine.
Fuel Fill: On the starboard side of the swim platform.
Fuel Tank: In the engine compartment at the front.
Generator Control Panel: In the galley on the AC panel.
Generator Seawater Pickup Seacock: In the engine compartment on the port side.
Generator Circuit Breaker: On the generator.
Macerator Underwater Discharge Seacock: In the engine compartment centered on the transom.
Marine Head Seawater Pickup Seacock: In the engine compartment on the port forward side.
Navigation lights: Red and green lights at the bow. White all-around light on the radar wing (if equipped).
Transom Shower: Inside the transom storage compartment.
Waste Holding Tank: In the engine compartment.
Water Fill: On the starboard side of the deck at mid ship.
Water Heater: In the aft berth utility compartment
Water Pump: In the aft berth utility compartment
Water Pump Switch: On the galley cabinet forward of microwave.
Water Tank: Under the salon/galley floor. The access for the tank fittings is under the entry steps.
Windlass Circuit Breakers: In the cabinet under the cockpit sink.
Windlass Circuit Foot Controls: At the bow next to windlass.
13
305 • Owner’s Manual Supplement
Chapter 3: Propulsion & Related Systems
Engine
The owner’s packet contains detailed engine operation and maintenance manuals. Be sure to read and understand
these manuals before starting or doing any maintenance on the engine.
Engine Room Ventilation System
!
•
•
•
•
WARNING!
FIRE/EXPLOSION HAZARD
Use of the blower system is NOT A GUARANTEE that explosive fumes have been removed.
If you smell fuel, DO NOT start the engine or generator and DO NOT turn On any
electrical devices.
If you smell fuel and the engine and/or generator is already running, SHUT OFF the engine
and/or generator and TURN OFF all electrical devices. Investigate immediately.
DO NOT obstruct or modify the ventilation system.
VIEW OF ENGINE
COMPARTMENT
UNDERSIDE VIEW OF DECK
HOSES ROUTE TO
ENGINE COMPARTMENT
BLOWERS
AFT
TO BLOWERS
MOUNTED ON DECK
•
•
•
•
The bilge blowers remove explosive fuel fumes from the engine compartment.
Fresh air is drawn into the compartment through the deck vents.
The bilge blower switch is at the helm.
If the boat is equipped with a generator, there is a second bilge blower switch on the main AC panel.
To make sure the engine compartment is ventilated with fresh air, run the bilge blower:
• For at least four minutes before starting the engine.
• During starting.
• Anytime your boat is running below cruising speed.
14
305 • Owner’s Manual Supplement
Chapter 3: Propulsion & Related Systems
Fire Suppression System (If Equipped)
MANUAL
DISCHARGE HANDLE
FIXED FIRE
EXTINGUISHER
• The fire suppression system is designed to extinguish a fire in the engine compartment.
• Before using your boat for the first time, read and understand the fire suppression system’s instruction and maintenance manual and follow all warnings.
Observe the following:
• The system will go off automatically whenever direct heat from a fire is detected in the engine compartment.
• The system can be set off manually by pulling the T-handle (labeled "FIRE") at the helm.
• The system can only be set off once during a fire. After the system is discharged it must be refilled and refurbished before it can be used again.
15
Chapter 3: Propulsion & Related Systems
305 • Owner’s Manual Supplement
Fuel System
!
WARNING!
FIRE/EXPLOSION HAZARD!
• It is very important that the fuel system be inspected thoroughly the first time it is filled and
at each subsequent filling.
• For your safety and the safety of your passengers, the fueling instructions in the Cruiser &
Yacht Owner’s Manual must be carefully followed.
!
CAUTION
Avoid the storage or handling of gear near the fuel lines, fittings and tank.
Diagrams
GAS FUEL SYSTEM (IF EQUIPPED)
FUEL
TANK
FUEL LINES
TO ENGINES
FUEL TANK
VENT HOSE
FUEL FILL
HOSE
DIESEL FUEL SYSTEM (IF EQUIPPED)
FUEL SHUTOFF
VALVES
FUEL TANK
VENT HOSE
FUEL
FILTERS
FUEL FILL
HOSE
FUEL TANK
FUEL RETURN
LINES
FUEL LINES
TO ENGINES
16
305 • Owner’s Manual Supplement
Chapter 3: Propulsion & Related Systems
Fuel Fill and Vent
• The fuel fill fitting is marked “GAS” or “DIESEL”.
• The fuel tank vent is located below the fuel fill.
• If you experience difficulty filling the fuel tank, check to see if the fuel fill hose or vent hose is kinked or collapsed. If there are no visible signs of a problem, contact your local dealer.
Fuel Filters
• The fuel pickup tube (located inside the fuel tank) is equipped with a fine mesh screen filter.
• In addition, when supplied by the engine manufacturer, a fuel filter is installed on the engine.
• Periodically replace the fuel filters to make sure they remain clean and free of debris.
• Consult with your selling dealer or local marina concerning fuel additives that help to prevent fungus or other
buildup in your fuel tank.
Anti-siphon Valve
NOTICE
• If an engine running problem is diagnosed as fuel starvation, check the anti-siphon valve. If
the valve is stuck or clogged, change or replace it while the engine is shut down.
• NEVER run the engine with the anti-siphon valve removed, except in an emergency.
•
•
•
•
Your boat is equipped with an anti-siphon valve, which is an integral part of fuel system.
The valve is located at the point where the fuel feed line attaches to the fuel tank.
The valve is spring loaded and is opened by fuel pump vacuum.
This valve will prevent fuel from siphoning from the tank in the event of a fuel line rupture.
17
Chapter 3: Propulsion & Related Systems
305 • Owner’s Manual Supplement
Quick Oil Drain System
QUICK OIL DRAIN SYSTEM
TRANSOM
OIL DRAIN HOSE
OIL DRAIN PLUG
ENGINE OIL PAN
GARBOARD
DRAIN PLUG
DRAW
CORD
BILGE
GARBOARD
DRAIN
To drain the engine oil:
1.
2.
3.
4.
5.
6.
7.
8.
Remove the boat from the water.
Unscrew the garboard drain plug.
Pull the draw cord until the oil drain plug and the oil drain hose slide out of the garboard drain.
Place the end of the oil drain hose into a suitable container.
Unscrew the oil drain plug and drain the engine oil.
Replace the oil drain plug.
Push the drain hose back into the bilge.
Replace the garboard drain plug.
Always dispose of waste oil in accordance with local regulations.
18
305 • Owner’s Manual Supplement
Chapter 4: Controls
Steering
• This boat features a power assisted rack-and-pinion steering system.
• Check the fluid level in the power steering reservoir every time you use your boat.
• Boat steering is not self-centering.
Shift/Throttle
!
WARNING!
LOSS OF CONTROL HAZARD!
Improper maintenance of shift/throttle hardware may cause a sudden loss of control!
• Carefully read and understand all of the information about the shift/throttle in the
Cruiser & Yacht Owner’s Manual.
• Also, read and understand the shifter/throttle and engine manuals included in your owner’s packet.
Power Trim and Tilt
• The stern drive on your boat is equipped with power
trim and tilt.
• Trim and tilt instructions are provided in the engine
operation manual and the shifter/throttle manual,
included in your owner’s packet.
TRIM/TILT
PUMPS
TRIM TAB
PUMP
19
Chapter 4: Controls
305 • Owner’s Manual Supplement
Trim Tabs
!
WARNING!
LOSS OF CONTROL HAZARD!
Improper use of trim tabs will cause loss of control!
• DO NOT allow anyone unfamiliar with trim tabs to use them.
• DO NOT use trim tabs in a following sea as they will cause broaching or other unsafe
handling characteristics.
• DO NOT use trim tabs to compensate for excessive unequal weight distribution.
VIEW OF HELM
TYPICAL TRIM TAB
ROCKER SWITCHES
TYPICAL TRIM TAB
(TRANSOM VIEW)
TRANSOM
TRIM TAB
(TYPICAL)
• The trim tabs may be used to help keep your boat level at cruising speeds.
• The trim tabs are controlled by two rocker switches at the helm.
• Before using the trim tabs read and understand the trim tab operation manual included in your boat’s
owner’s packet.
Observe the following:
• Once cruising speed is reached, the port or starboard trim switch may be used (one at a time) to level the boat.
• Perform trim tab adjustment with several short touches to the switch rather than one long one.
• After each short touch allow several seconds for the hull to react.
• The trim tab hydraulic fluid reservoir is located in the engine compartment. The fluid level must be checked periodically (at least once a year) and refilled as necessary.
20
305 • Owner’s Manual Supplement
Chapter 5: Navigation & Communications Equipment
The owner’s packet contains manuals for all navigation & communication equipment installed on your boat. Thoroughly read and understand these manuals before using these systems for the first time and observe the following:
VHF Radio (If Equipped)
Your boat may include a VHF (Very High Frequency) radio. The VHF radio can be used to access weather reports,
summon assistance or contact other vessels as permitted by the FCC (Federal Communications Commission). Contact the FCC for licensing, rules and regulations concerning VHF radio usage.
Compass
NOTICE
• Compass accuracy can be affected by many factors.
• Have a qualified technician calibrate your compass. Make sure the technician gives you a
deviation card which shows the corrections to apply in navigational calculations.
• Keep a copy of the deviation card at each helm.
Depth Finder
!
WARNING!
• DO NOT use the depth finder as a navigational aid to prevent collision, grounding, boat
damage or personal injury.
• When the boat is moving, submerged objects will not be seen until they are already under
the boat.
• Bottom depths may change too quickly to allow time for the boat to react.
• If you suspect shallow water or submerged objects, run the boat at very slow speeds.
21
305 • Owner’s Manual Supplement
Chapter 6: Plumbing
Bilge Pumps
NOTICE
Discharge of oil, oil waste or fuel into navigable waters is prohibited by law. Violators are subject to legal action by the local authorities.
AFT BILGE PUMP
& FLOAT SWITCH
AFT BILGE DRAIN
FORWARD BILGE DRAIN
FORWARD BILGE PUMP
& FLOAT SWITCH
• Your boat is equipped with two automatic impeller-type bilge pumps which are used to pump water out
of the bilge.
• The bilge pumps are controlled by automatic bilge pump float switches (autofloat switches) and/or switches
at the helm.
• The bilge pumps are wired directly to the battery so they will normally function even when the boat is completely
shut down and left unattended.
22
305 • Owner’s Manual Supplement
Chapter 6: Plumbing
Bilge Pump Testing
• Bilge pumps are critical to the safety of your boat.
• Check the bilge pumps often to make sure they are working.
• Individually test each pump as follows:
1. Turn On bilge pump switch at helm.
2. Make sure water in bilge is pumped overboard.
• If there is water in the bilge and the pump motor is running but not
pumping inspect the discharge hose for a kink or collapsed area.
• If no problems are found, check the bilge pump housing for clogging debris as follows:
BILGE PUMP
COMPONENTS
TAB
1. Remove power cartridge:
a. Lift tab while rotating fins counter-clockwise.
b. Lift out power cartridge.
c. Clear outer housing of debris.
2. Reinstall power cartridge:
a. Make sure “O” ring is properly seated.
b. Coat “O” ring with a light film of vegetable or mineral oil.
c. Align two cams on either side of power cartridge with two
slots on outer housing and press power cartridge into housing
while twisting clockwise.
3. Check reinstallation by trying to twist fins counter-clockwise
without lifting tab; cartridge should stay in place.
“O” RING
FIN
OUTER
HOUSING
POWER
LIGHT
CARTRIDGE
FILM
CAM
OF OIL (TYPICAL)
SLOT (TYPICAL)
Autofloat Switches
• Automatic bilge pumps use electromagnetic float (autofloat) switches to turn On the pump whenever water rises
above a preset level in the bilge.
• One autofloat switch is mounted next to each automatic bilge pump.
• Autofloat switches are wired directly to the battery and will normally function even when the boat is completely
shut down and left unattended.
Test the autofloat switches often as follows:
FLOAT SWITCH TESTING
1. Push float switch test button up to turn
On bilge pump.
If the pump does not turn On, check the
inline fuse. If the fuse is good but the switch
doesn’t work, it may indicate a bad switch or
possibly a low battery.
FLOAT SWITCH
TEST BUTTON
2. Push test button all the way down to
return the float switch to auto mode.
!
FLOAT UP - TEST MODE
FLOAT DOWN - AUTO MODE
BILGE PUMP SHOULD TURN ON
BILGE PUMP SHOULD TURN OFF
CAUTION!
When test is completed on each float switch, you MUST push the test button ALL THE WAY
DOWN to the auto position to return the switch to auto mode!
23
Chapter 6: Plumbing
305 • Owner’s Manual Supplement
Seawater Systems
Seacocks
!
CAUTION!
SYSTEM DAMAGE HAZARD!
• Before using a seawater pickup system, make sure that the system’s seacock is in the Open
position before the system is started and keep the seacock Open until the system is shut Off.
• Close the seacocks whenever the systems will not be used for long periods of time.
A seacock is a valve, controlled by a 90º lever, used to manage
the pickup of seawater through the hull and below the water
line. Seacocks are typically used on your boat in the following
seawater pickup systems:
• Generator (if equipped)
• Marine head (toilet)
• Air conditioning system (if equipped)
Before using any of these systems, make sure that the system’s
seacock is Open and remains Open until the system is shut Off.
SEAWATER PICKUP VALVE (SEACOCK)
COMPONENTS (TYPICAL)
90 DEGREE
SEACOCK
LEVER
HULL
SECTION
SEACOCK (TYPICAL)
SEACOCK GASKET
PICKUP STRAINER
Seawater Strainers
• Seawater strainers are used in water pickup systems to filter incoming seawater.
• A seawater strainer is located near each system’s seacock.
• Check the strainers for leaks and/or debris every time you use your boat.
• If debris is found, clean the seawater strainer as follows:
!
CAUTION!
FLOODING HAZARD!
• The seacock that sends seawater to the strainer must be CLOSED before disassembling
the seawater strainer to prevent the boat from taking on water through the seawater
strainer assembly.
• Keep the seacock CLOSED until the seawater strainer is completely reassembled.
SYSTEM DAMAGE HAZARD!
• After reassembling the seawater strainer, make sure that the seacock valve is OPEN before
using the component/system.
1. Make sure the component/system (generator, air conditioning system, etc.) that the strainer is connected to is
turned Off.
2. Close the seacock that sends seawater to the strainer you are about to clean. The seacock must remain Closed
until the strainer is completely reassembled.
3. Take apart the seawater strainer.
4. Remove the debris.
5. Flush the strainer with water.
6. Reassemble the seawater strainer.
7. Open the seacock and check for leaks around the strainer. If no leaks are found, you may use the component
or system.
24
305 • Owner’s Manual Supplement
Chapter 6: Plumbing
Freshwater System
!
WARNING!
• Only use safe drinking (potable) water in your boat’s freshwater system.
• Only use a sanitary drinking water hose to fill the water tank or connect to city water.
• Never use a common garden hose for drinking water.
TRANSOM SHOWER
(IF EQUIPPED)
COCKPIT
FAUCET
SYSTEM
DRAIN
•
•
•
•
•
WATER
HEATER
WATER PUMP
HEAD
GALLEY
WATER TANK
WATER TANK
VENT
WATER FILL
DECK FITTING
Read the Freshwater System section in the Cruiser & Yacht Owner’s Manual.
Your boat is equipped with a pressure type (demand) freshwater (potable) system.
This system can be pressurized by turning On the water pump.
See the Component Location section of this Supplement for the location of the water pump switch.
Since the water pump requires DC power, the battery switch must be in the "1", "2" or "BOTH" position for the
pump to work.
Observe the following about the freshwater system:
• Turn Off the water pump when the boat is not in use or the water tank is empty.
• Inspect and clean the water filter often (located on the water pump).
• When your boat is to be left unattended for long periods of time, pump the water tank dry to prevent stored water
from becoming stagnant and distasteful.
• If the freshwater system needs to be disinfected, ask your dealer about treatments available for your boat’s system.
25
Chapter 6: Plumbing
305 • Owner’s Manual Supplement
Freshwater System Winterization
!
CAUTION!
WATER SYSTEM DAMAGE HAZARD!
Never blow compressed air through the water system when all of the faucets are Closed.
1. Turn On the water system switch.
2. Open all of the faucets and showers and let the water system drain completely.
3. Turn Off the water system switch.
Any remaining water must be removed from the water lines. There are two ways to remove the remaining water from
the lines:
• Compressed Air
• Gravity Draining
Compressed Air
You must have an air compressor with an air hose
and an air nozzle.
1. Remove the water line from the outlet side of
the water pump (opposite side from filter).
2. Open the faucet that is furthest away from the
water pump.
3. Place the air nozzle against the end of the just
removed water line and blow air through
the system.
4. When water stops coming out of the Open faucet, stop the air and Close the faucet.
5. One at a time, repeat this process on all faucets
and showers.
NOTE: LOCATION OF
TEE FITTING & DRAIN
PLUG MAY VARY
TYPICAL VIEW
DRAIN PLUG
INLET SIDE
WATER LINE
FILTER
WATER PUMP
Gravity Draining
1. Open all faucets and showers.
2. Remove the drain plug from the tee fitting on
the freshwater tank.
3. When the water has stopped draining from the
freshwater tank, replace the drain plug.
OUTLET SIDE
WATER LINE
FRESHWATER TANK
TEE FITTING
Transom Shower
• Your boat is equipped with a freshwater transom shower.
• The water pump switch must be turned On before using the transom shower.
• Be sure to read the manufacturer’s instructions, provided in your boat’s owner’s packet.
26
305 • Owner’s Manual Supplement
Chapter 6: Plumbing
Water Heater
!
WARNING!
HOT HAZARD!
Water heated by the water heater can reach temperatures hot enough to scald the skin.
!
CAUTION!
WATER HEATER DAMAGE HAZARD!
• DO NOT turn On the water heater electrical circuit on the AC panel until the water heater
tank is COMPLETELY filled with water.
• Even momentary operation in a dry tank will damage the heating elements.
• Warranty replacements WILL NOT be made on elements damaged in this manner.
• The tank is full if water flows from the tap when the hot water is turned On in the galley.
• The water heater should be drained and the power turned Off when the possibility of
freezing exists.
NOTICE
If your boat is connected to shore power or generator power, but the water heater is
not working:
• Make sure the water heater circuit breaker on the AC panel is switched On.
If the circuit breaker on the AC panel is On, but the water heater is still not working:
• Consult with your dealer about checking the "push to reset" circuit breaker located on the
water heater.
• The water heater is connected to the AC power system, therefore, you must make sure that the water heater
breaker on the AC panel is turned On before water will be heated.
• Read the manufacturer’s instruction manual supplied in your boat’s owner’s packet and observe the
warnings above.
Winterizing the Water Heater
1. Turn Off the water heater breaker.
2. Disconnect the hose (A) attached to the pressure relief valve (B).
3. If there is any water in this hose, drain it into
the bilge or into a bucket.
4. Open the pressure relief valve (B).
5. Open the drain valve (C).
• Leave the pressure relief and drain valves
Open until you fit out the boat after storage.
B
A
C
27
Chapter 6: Plumbing
305 • Owner’s Manual Supplement
Drain Systems
Deck Drains
NOTE:
VIEW IS THROUGH
TOP SIDE OF DECK
COCKPIT SINK DRAIN
DECK DRAINS
COCKPIT DRAINS
• Water on the deck is drained overboard through the deck drains.
• Keep the deck drains free of debris.
Sink Drains
Gray water (water from sinks) above the waterline is gravity drained overboard.
Shower Drains
• The shower is drained into a sump box.
• A float switch automatically turns On the sump pump.
• The sump pump pumps the shower water overboard.
Sump Box Cleaning
SHOWER SUMP BOX IS ACCESSED THROUGH
FLOOR CUT OUT UNDER SALON ENTRY STEPS
C
Periodically clean the sump box (A), filter, and pump as follows:
1. Remove the cover screws (B) and the cover (C).
2. Remove any debris from the box and the filter.
3. Clean the sump pump as outlined in the Bilge Pump section of
this Supplement.
Sump System Winterization
Drain the sump pump system in the winter months when not in use.
1. Disconnect and drain all lines to the unit.
2. Remove the screws from the mounting feet (D) and drain
the system.
3. Reinstall the screws in the mounting feet and reconnect the system.
28
A
D
B
305 • Owner’s Manual Supplement
Chapter 6: Plumbing
Marine Head With Holding Tank
•
•
•
•
•
Your boat comes equipped with a marine head (toilet) and waste holding tank system.
Read the manufacturer’s operation and maintenance manual (included in your boat’s owner’s packet).
The holding tank is plumbed to a waste fitting on the deck for dockside pump-out.
You can determine the content level of the holding tank by looking at the side of the tank.
Empty the holding tank at every opportunity.
Electric Flush (If Equipped)
HOLDING TANK
WASTE PUMP-OUT
DECK FITTING
HOLDING TANK
VENT
SEAWATER PICKUP
& BALL VALVE
HEAD
AFT
• The electric flush marine head installed on your boat uses seawater to flush waste from the toilet.
• The seawater pickup valve (seacock) must be Open for the head to work.
29
Chapter 6: Plumbing
305 • Owner’s Manual Supplement
Macerator (If Equipped)
NOTICE
Check with local authorities for regulations regarding the legal use of marine head systems.
HOLDING TANK
WASTE PUMP-OUT
DECK FITTING
HOLDING TANK
VENT
SEAWATER PICKUP
& BALL VALVE
HEAD
MACERATOR
(IF EQUIPPED)
OVERBOARD
DISCHARGE
THRU-HULL
To use the macerator to pump waste directly into the water (where regulations permit):
1. Open the underwater discharge seacock.
2. Press both macerator switches at the same time to run the pump. Do not continue running the macerator if the
waste holding tank is empty.
3. Close the underwater discharge seacock when you are done pumping.
30
305 • Owner’s Manual Supplement
Chapter 7: Deck Equipment
Canvas
!
CAUTION!
Take down and securely stow the convertible top, side curtains and back cover before transporting your boat by road.
EYE
END
PIN
C
DECK
HINGE
E
H
D
H
F
G
A
B
1. Slide the eye ends of the main bow (A) into the forward deck hinges (B) and insert the pins.
2. Slide the eye ends of the aft legs (C) into the upper deck hinges on the radar wing (D) and insert the pins
3. Unfold the canvas top (E) and slide the eye ends of the forward legs (F) into the lower hinges on the windshield
frame (G) and insert the pins.
4. Attach the snaps to the deck and the windshield frame.
• No adjustments to the bow jaw slides (H) should need to be made as they are preset during manufacturing.
• Before trying to adjust the jawslide positions, obtain the correct measurements from your selling dealer.
31
Chapter 7: Deck Equipment
305 • Owner’s Manual Supplement
Windlass (If Equipped)
!
CAUTION!
PRODUCT DAMAGE HAZARD!
• DO NOT pull the boat to the anchor using the windlass or continue to operate the windlass if
it has stalled or is overloaded.
• Read and follow the manufacturer’s instruction manual supplied in your boat’s owner’s packet before using the
anchor windlass for the first time.
• The windlass can be controlled from a switch at the helm or from the deck foot switches.
• Make sure that the windlass breaker is turned On before using the anchor windlass.
• To haul the anchor, use engine power (not the windlass) to move the boat to, and directly above, the anchor. Use
the windlass to dislodge the anchor from the bottom by pulling it straight up.
Cleats and Tow Eyes
!
WARNING!
PERSONAL INJURY and /or PRODUCT or PROPERTY DAMAGE HAZARD!
• NEVER lift the boat using the bow and stern eyes or the cleats.
Carefully read the section on towing in the Cruiser & Yacht Owner’s Manual before towing anything behind the boat
or having the boat towed by another vessel.
32
305 • Owner’s Manual Supplement
Chapter 8: Appliances & Entertainment Systems
NOTICE
Always keep an approved ABC-type fire extinguisher in galley area.
All appliances installed on your boat come with their own manuals. These manuals contain detailed instructions and
important safeguards. Thoroughly read and understand these manuals before using your boat’s appliances.
• Make sure the AC breaker is turned On for the appliance you wish to use.
Refrigerator
Your boat features a 120-volt AC/12-volt DC refrigerator. The refrigerator runs on 12-volt DC power unless 120-volt
AC power is being supplied by the generator (if equipped) or shore power and the AC refrigerator breaker is On.
Electric Stove (If Equipped)
!
•
•
•
•
•
•
WARNING!
BURN/SCALDING and/or FIRE HAZARD!
Read the stove’s instruction manual before using.
Always keep an approved ABC-type fire extinguisher in galley area.
Do not use the stove while underway.
Any non-cooking devices on or near your stove during use are potential fire hazards!
DO NOT touch burners, grates or nearby surfaces as they may be hot even when they are
dark in color. Areas near burners and grates may become hot enough to cause burns.
During and after use, do not touch or let clothing or other flammable material come in contact with heated units or areas near the units (burner tops, main frame sides and back, sea
rails and pot holders) until they have had sufficient time to cool.
33
Chapter 8: Appliances & Entertainment Systems
305 • Owner’s Manual Supplement
Alcohol/Electric Stove (If Equipped)
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
• The alcohol stove is a source of dangerous carbon monoxide gas (CO).
• BEFORE using the alcohol stove, Open doors and windows to make sure
there is enough fresh air for ventilation.
!
WARNING!
• Open flame cooking appliances consume oxygen, this can cause asphyxiation or death.
• Maintain open ventilation.
!
•
•
•
•
•
•
WARNING!
BURN/SCALDING and/or FIRE HAZARD!
Read the stove’s instruction manual before using.
Always keep an approved ABC-type fire extinguisher in galley area.
Do not use the stove while underway.
Any non-cooking devices on or near your stove during use are potential fire hazards!
DO NOT touch burners, grates or nearby surfaces as they may be hot even when they are
dark in color. Areas near burners and grates may become hot enough to cause burns.
During and after use, do not touch or let clothing or other flammable material come in contact with heated units or areas near the units (burner tops, main frame sides and back, sea
rails and pot holders) until they have had enough time to cool.
!
CAUTION!
PRODUCT DAMAGE HAZARD!
To prevent overheating which can destroy the electric burner elements, NEVER attempt to use
both alcohol and electric burners simultaneously.
Audio & Visual Equipment
NOTICE
AM radio reception may be impaired anytime the engine or generator is running.
All audio and visual equipment installed on your boat have separate instruction sheets or manuals that explain their
use in detail.
34
305 • Owner’s Manual Supplement
Chapter 9: Convertible Seats, Beds, & Tables
Dinette/V-Berth
A
B
1
C
E
D
C
2
3
The dinette table can be removed and the dinette area can be converted into a berth.
1. Remove the table (A) and the table leg (B).
2. Place the filler board (C) so that it fits securely into the recessed edge (D) at the front of the dinette seats.
3. Place the filler cushion (E) on top of the filler board (C).
35
Chapter 9: Convertible Seats, Beds, & Tables
305 • Owner’s Manual Supplement
Cockpit
Cockpit Table/Sunlounge
A
B
C
A
A
D
The aft cockpit table and table leg can be removed and the seating can be converted into a flat sunlounge.
1.
2.
3.
4.
5.
36
Lift the table (A) and remove table leg (B).
Put the cross supports (C) in place.
Place the table (A) on top of the supports (C).
Place the cushion (D) on top of the table (A).
Make sure that all parts are secure before using the sunlounge.
305 • Owner’s Manual Supplement
Chapter 10: Lights
Care and Maintenance
All of the lights installed on your boat are of top quality, but you should be aware that failure may periodically occur
for a variety of reasons:
1.
2.
3.
4.
There may be a blown fuse - replace the fuse.
The bulb may be burned out - carry spare bulbs for replacement.
A wire may be damaged or may have come loose - repair as required.
The bulb base may be corroded - clean the base and coat it with non-conductive electrical lubricant.
Navigation Lights
!
CAUTION!
Avoid the storage of gear where it would block navigation lights from view.
Read and understand the navigation light section of Cruiser & Yacht Owner’s Manual.
Interior & Exterior Lights
!
CAUTION!
• Be conservative in the use of battery power.
• Prolonged use of cabin interior lights (overnight) will result in a drained battery.
•
•
•
•
The lights are powered by the boat’s 12 volt DC system.
The battery switch must be in the 1, 2 or BOTH position for the lights to work.
There are On/Off light switches for different sets of lights on the cabin wall.
Some individual lights also have a switch on the light.
Spotlight (If Equipped)
Your boat may come equipped with a spotlight which can be controlled by a switch at the helm. Instructions can be
found in the spotlight’s operating manual (included in your boat’s owner’s packet).
37
305 • Owner’s Manual Supplement
Chapter 11: Heating & Air Conditioning
Air Conditioning System (If Equipped)
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
Dangerous carbon monoxide gas (CO) can be brought into the boat through
the air conditioning system.
!
CAUTION!
SYSTEM DAMAGE HAZARD!
The air conditioning system’s seacock must be OPENED before turning on the air conditioner
and must remain OPEN during use.
SEAWATER PICKUP
& BALL VALVE
SEA
STRAINER
PICKUP
PUMP
HEAD
VENT
AIR CONDITIONER AIR CONDITIONER
SUMP PUMP
DRAINS
HEAD
AFT BERTH
VENT
AIR CONDITIONER
SALON
VENT
V-BERTH
VENT
Your boat may be equipped with an air conditioning system. Read the air conditioner manual, included in your
owner’s packet, before using the air conditioning system.
• Before using the air conditioning system, make sure the breakers on the AC main distribution panel are turned On
and make sure the system’s seawater pickup seacock is Open. The seacock must remain Open anytime the air
conditioner is in use.
• Check the seawater pickup strainer for debris according to the directions given in the Seawater Strainer section of
this Supplement.
38
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
!
•
•
•
•
•
EXTREME FIRE, SHOCK & EXPLOSION HAZARD!
To minimize the risks of fire and explosion, NEVER install knife switches or other arcing
devices in the fuel compartments.
NEVER substitute automotive parts for marine parts. Electrical, ignition and fuel system
parts were designed and manufactured to comply with rules and regulations that minimize
risks of fire and explosion.
DO NOT modify the electrical systems or relevant drawings.
Have qualified personnel install batteries and/or perform electrical system maintenance.
Make sure that all battery switches are turned OFF before performing any work in the
engine spaces.
!
•
•
•
•
DANGER!
WARNING!
FIRE & EXPLOSION HAZARD!
Fuel fumes are heavier than air and will collect in the bilge areas where they can be accidently ignited.
Visually and by smell (sniff test), check the engine and fuel compartments for fumes or accumulation of fuel.
ALWAYS run the bilge blowers for at least four minutes prior to engine and/or generator
starting, electrical system maintenance or activation of electrical devices.
Minimize the danger of fire and explosion by not exposing the batteries to open flame or
sparks. NEVER smoke anywhere near the batteries.
!
CAUTION!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
NEVER disconnect the battery cables while the engine is running since it can cause
damage to your boat’s electrical system components.
NOTICE
Electrical connections are prone to corrosion. To reduce corrosion caused electrical problems,
keep all electrical connections clean and apply a spray-on protectant that is designed to protect
connections from corrosion.
39
Chapter 12: Electrical System
305 • Owner’s Manual Supplement
12 Volt DC System
Batteries
The batteries supply electricity for lights, accessories, engine and generator (if equipped) starting.
The Electrical section of Chapter 8, in the Cruiser & Yacht Owner’s Manual, provides battery, care and maintenance instructions.
Fuses and Circuit Breakers
• Fuses and circuit breakers for engines and main accessory power are on the DC main distribution panel and on the
battery switch panel.
• Some equipment may have secondary fuse protection at the unit, behind the battery switch panel, or at
the batteries.
• Electronics power is provided at the helm station.
40
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
Battery Switches
!
CAUTION!
ENGINE & ELECTRICAL SYSTEM DAMAGE HAZARD!
NEVER change battery switch positions while the engine is running. It can cause damage to
your boat’s engine alternator.
NOTICE
Since the batteries on your boat were dealer-installed, the battery switch positions listed below
may vary. Make sure you get a full explanation of battery switch use from your selling dealer.
• Each battery switch has four (4) positions.
• The normal settings are:
Engine battery switch - position “2”.
House battery switch - position “1”.
• Some "Standby Loads", such as the CO monitor, the automatic bilge pumps, and the stereo memory, are not
affected by the battery switch since they are wired directly
to the battery (see the Wiring Diagrams in this Supplement
for more details).
NORMAL BATTERY
SWITCH POSITIONS
POSITION "2"
POSITION "2"
Battery Switch
Position
POSITION
1
POSITION
2
POSITION
BOTH
POSITION
OFF
Engine Starting
Accessories and Lights
Engine Alternator
Battery 1
Provides Starting Power
Battery 1
Provides Power for
Accessories and Lights
Charges
Battery 1
Battery 2
Provides Starting Power
Battery 2
Provides Power for
Accessories and Lights
Charges
Battery 2
BOTH Batteries
Provide Starting Power
BOTH Batteries Provide Power for
Accessories and Lights (not
advised unless engine is running)
Charges BOTH
Batteries
Prevents Start/Run
Batteries Provide Power for Standby
Loads Only
Dot Not Run Engine
in this Position
41
Chapter 12: Electrical System
305 • Owner’s Manual Supplement
Alternator
The engine alternator will keep the batteries properly charged when running at cruising speeds.
Battery Charger
!
CAUTION!
ENGINE & ELECTRICAL SYSTEM DAMAGE HAZARD!
NEVER run the boat’s engine and the battery charger at the same time.
!
CAUTION!
The battery charging systems (alternator and battery charger) installed on your boat are
designed to charge conventional lead-acid batteries. Before installing gel-cell or other new technology batteries, consult with the battery manufacturer about charging system requirements.
Your boat is equipped with a battery charger. Thoroughly read
and understand the battery charger manual (provided in your
boat’s owner’s packet) before using the battery charger for the
first time.
• The battery charger will charge the boat’s batteries whenever
the boat is plugged into 120V/60Hz shore power and the
"BATTERY CHARGER" AC breaker is On.
• The battery charger is independent of the battery switch. For
proper charging, the battery switch can be in any position.
• You may use DC powered electrical systems, such as the lights
and stereo when the battery charger is On, but there will be a
corresponding drop in charger performance.
42
BATTERY CHARGER LOCATION
VIEW OF MID-BERTH
BATTERY
CHARGER
MID-BERTH
CUTOUT
WATER
HEATER
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
120 Volt AC System
!
CAUTION!
WATER HEATER DAMAGE HAZARD!
• DO NOT turn on the water heater AC panel electrical circuit until the water heater tank is
COMPLETELY filled with water.
• The tank is full if water flows from the tap when the hot water is turned On in the galley.
• Even momentary operation in a dry tank will damage the heating elements.
• Warranty replacements WILL NOT be made on elements damaged in this manner.
SINGLE SHORE POWER AC PANEL
NOTICE
Whether using shore power or generator power, the simultaneous use of several AC components can result in an overloaded circuit. It may be necessary to turn Off one or more accessories in order to use another accessory.
• Τhe 120V/60Hz AC system can be energized by shore power or generator power (if equipped).
• The master circuit breakers, located on the AC panel, provide power source selections to AC powered accessories.
Individual breakers must be turned On to supply power to the accessories you wish to use.
• The AC panel may contain inactive circuit breakers for accessories that are not available for this model boat.
43
Chapter 12: Electrical System
305 • Owner’s Manual Supplement
Shore Power
!
•
•
•
•
•
DANGER!
FIRE, EXPLOSION & SHOCK HAZARD!
DO NOT alter shore power connectors and use only compatible connectors.
Before connecting or disconnecting the shore power cord to your boat, make sure all breakers and switches on the AC master panel are turned OFF.
To prevent shock or injury from an accidental dropping of the “hot” cord into the water,
ALWAYS attach the shore power cord to the boat inlet first; then to the dockside connection.
When disconnecting from shore power, disconnect the shore power cord from the dockside
connection first.
NEVER leave a shore power cord connected to the dockside connection only.
Only use shore power cords approved for marine use. NEVER use ordinary indoor or outdoor extension cords that are not rated for marine use.
!
WARNING!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
• Monitor the polarity indicator lights EVERY TIME you connect to shore power.
• If a red reversed polarity light turns On when you are connecting to shore power, DO NOT
energize the main breaker switches.
• Instead, IMMEDIATELY disconnect the shore power cord (ALWAYS from the dockside
receptacle first) and notify marina management.
!
•
•
•
•
WARNING!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
Periodically check the shore power cord(s) for deterioration or damage.
NEVER use damaged or faulty cords since the danger of fire and electrical shock exists.
DO NOT pinch shore power cords in doors or hatches, or coil the shore power cord too
tightly since these situations can generate enough heat to result in a fire.
If a shore power cord accidently becomes immersed in water, THOROUGHLY dry the
blades and contact slots before reusing.
!
CAUTION!
ELECTRICAL SYSTEM DAMAGE HAZARD!
• NEVER connect to dockside power outside of North America unless you have purchased the
international electrical conversion option.
• The simultaneous use of several AC components can result in an overloaded circuit. It may
be necessary to turn Off one or more accessories in order to use another accessory.
• Use double insulated or three-wire protected electrical appliances whenever possible.
NOTICE
Some dockside installations may be rated less than 30 amps, therefore, you may need to purchase lower amp adapters. Whenever a lower amp adapter is used, however, there will be a corresponding drop in supplied power from the dockside system.
44
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
NOTE: SINGLE INLET STANDARD
DUAL INLETS WITH AIR CONDITIONER
(IF EQUIPPED)
TYPICAL SHORE
POWER INLET
SHORE POWER
INLET(S)
Connecting To Shore Power
• The single shore power 120V/60Hz, AC system (if equipped) features one, 120V/30 amp, shore power receptacle.
• If your boat is equipped with an air conditioning system, a second (dual) 30 amp inlet has been installed.
• The dual shore power inlets are labeled "LINE 1" and "LINE 2", which corresponds to the "LINE 1" and "LINE 2"
master breakers on the AC panel.
• The dual shore power system is designed so that each line is independent of the other except when the AC power
transfer switch is used.
45
Chapter 12: Electrical System
LINE 1
DOCKSIDE MASTER
305 • Owner’s Manual Supplement
DUAL SHORE POWER AC PANEL (IF EQUIPPED)
VOLTMETER
LINE 2
VOLTMETER
SELECTOR SWITCH
TRANSFER
LINE 2
DOCKSIDE MASTER
LINE 1
POLARITY
LIGHT
LINE 2
POLARITY
LIGHT
10 AMPS
15 AMPS
20 AMPS
15 AMPS
5 AMPS
15 AMPS
25 AMPS
15 AMPS
FIGURE 1
1.
2.
3.
4.
•
•
5.
6.
7.
Review all hazard information at the beginning of this section, Shore Power.
Turn Off all breakers and switches on the AC master panel.
Attach the shore power cord to the boat inlet first then to the dockside outlet.
Monitor the AC panel’s polarity indicator lights, located below the line master breaker(s), as follows:
A green light illuminating after the power cord is plugged into the dockside outlet indicates acceptable electrical power. You may turn On the master breaker switch.
A red light, however, indicates reversed polarity, which could cause electrical system damage and possibly
electrical shock injuries. In this case, do not turn On the master breaker switch.
Switch the "LINE 1 DOCKSIDE MASTER" On.
If equipped with dual dockside, switch the "LINE 2 DOCKSIDE MASTER" On.
Turn On the individual component breakers as required.
Transfer Switch (If Equipped with Dual Shore Power)
NOTICE
• When using the "Transfer Switch" do not exceed 30 total amps.
• The amperage of each component breaker is shown in figure 1.
• The voltage on each line can be read by setting the voltmeter selector switch.
When only one dockside outlet is available, you can use the "Transfer Switch" to provide power to both lines.
1. Connect to shore power as described in steps 1 through 4 above.
2. Switch the "LINE 1 TRANSFER SWITCH" (transfers power from line 1 to line 2) On instead of the
"LINE 2 DOCKSIDE MASTER.
3. Turn On the individual component breakers as required.
46
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
Generator (If Equipped)
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
• Generators are a source of dangerous carbon monoxide gas (CO). Check the
generator exhaust system for leaks before each use.
!
•
•
•
•
•
•
WARNING!
FIRE/EXPLOSION HAZARD!
Use the bilge blowers for a minimum of four minutes before starting the generator.
Leave the blowers on while the generator is running unless the boat is running at
cruising speed.
Use of the blower system is not a guarantee that explosive fumes have been removed.
If you smell any fuel, DO NOT start the generator.
If the generator is already running, IMMEDIATELY shut Off the generator and all
electrical accessories and investigate.
DO NOT obstruct or modify the ventilation system.
!
CAUTION!
SYSTEM DAMAGE HAZARD!
• Always make sure the generator’s seawater pickup seacock is OPEN before and during the
running of the generator.
• NEVER use the generator starter for more than 30 seconds.
• If the generator does not start, wait at least 30 seconds before another start attempt is made.
• After starting the generator, wait for the generator to stabilize before turning On component
breakers on the AC panel.
47
Chapter 12: Electrical System
305 • Owner’s Manual Supplement
SEA
STRAINER
GAS SYSTEM
(IF EQUIPPED)
SEAWATER PICKUP
& BALL VALVE
FUEL
FILTER
VENTED
LOOP
FUEL
TANK
EXHAUST
THRU-HULL
MUFFLER
FUEL SHUT-OFF
VALVE
FUEL
FILTER
DIESEL SYSTEM
(IF EQUIPPED)
GENERATOR
SEA
STRAINER
SEAWATER PICKUP
& BALL VALVE
GENERATOR
EXHAUST THRU-HULL
MUFFLER
• The generator (if equipped) can supply 120V/60Hz power to the boat when it is not connected to shore power.
• Prior to running your generator for the first time, read the generator manual for detailed information on pre-start
checks, break-in procedures and starting instructions.
Observe the following about your generator:
• Polarity has been established in the installation of the generator, therefore the polarity lights will not function
while in this mode.
• The coolant mixture installed at the factory consists of equal parts of water and anti-freeze (Ethylene Glycol). Frequently check the generator’s seawater strainer for leaks and/or debris as outlined in the seawater strainer section
of this Supplement.
• This system is designed so that ship’s generator and shore power sources can not supply power at the same time.
• To monitor the voltage generated by the generator, switch the voltage selector switch to the GENERATOR position.
48
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
Generator Use
AC PANEL, DUAL SHORE POWER & GENERATOR
MASTER BREAKER
LOCKOUTS
DOCKSIDE
MASTER
PRE HEAT
START
GENERATOR
MASTER SWITCHES
SELECTOR SWITCH
STOP
BLOWER
1. Run the bilge blowers for a minimum of four minutes before starting the generator.
• The blower switch is located on the AC panel near the generator controls.
• If your boat is running below cruising speed, leave the blowers On while the generator is running.
2. Make sure the generator’s seawater pickup seacock is Open before starting and during running of
the generator.
3. Make sure that the battery switch is turned to position "1" or "2".
4. Slide the master breaker lockouts to cover the dockside master breakers and reveal the generator
master breakers.
5. Switch the “GENERATOR LINE ONE MASTER” and the “GENERATOR/LINE ONE TRANSFER”
master breakers On.
6. On the AC panel, press up and hold the oil pressure switch (labeled "PRE HEAT") and the "START" switch at
the same time until the generator starts.
7. Turn On each individual component breaker as required.
To shut Off the generator, press up and hold the “STOP” switch until the generator completely shuts down.
49
Chapter 12: Electrical System
305 • Owner’s Manual Supplement
Electrical Routings
Deck Electrical Harness
NOTE: VIEW IS UNDERSIDE OF DECK
8
1
8
2
3
12
8
3
11
3
4
10
3
5
2
9
6
3
7
3
4
7
5
8
1
2
3
4
50
HEAD
WIPER
OVERHEAD LIGHTS
SPOT LIGHT
5
6
7
8
SPEAKER
WINDLASS CONTROL
NAVIGATION LIGHT
COURTESY LIGHT
9
10
11
12
TO SWITCHES
DASH
STEREO
RADAR WING/HORN
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
Windlass Electrical Harness (If Equipped)
NOTE: VIEW IS UNDERSIDE OF DECK
1
2
1
2
NEGATIVE TO BUSS BAR
POSITIVE TO WINDLASS CIRCUIT BREAKER
51
Chapter 12: Electrical System
305 • Owner’s Manual Supplement
Radar Wing Electrical Harness
1
2
3
1
4
5
6
1
2
3
52
COURTESY LIGHTS
HORN
ANCHOR LIGHT
4
5
6
PLUG
STARBOARD SPEAKER
PORT SPEAKER
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
Hull Electrical Harness
6
5
4
3
11
7
12
2
13
8
9
1
14
10
15
22
16
21
17
20
1
2
3
4
5
6
7
8
BATTERY SWITCH
WATER PUMP
HEAD SWITCHES
REFRIGERATOR
WATER PUMP SWITCH
AIR CONDITIONER SUMP BOX
BILGE PUMP
WATER PUMP
9
10
11
12
13
14
15
16
19
BATTERY CHARGER
FUEL TANK
TO DEPTH FINDER IN DASH
DIRECT CURRENT PANEL
AFT BERTH SWITCHES
BLOWER
TRANSDUCER
STARBOARD ENGINE
18
17
18
19
20
21
22
TILT PUMP
MACERATOR
BILGE PUMP
TRIM TAB PUMP
TILT PUMP
PORT ENGINE
53
Chapter 12: Electrical System
305 • Owner’s Manual Supplement
Battery System
1
6
7
7
5
AFT
STARBOARD
5
4
1
2
3
4
54
2
3
BATTERY SWITCH
DIRECT CURRENT PANEL
PORT BATTERY
STARBOARD BATTERY
5
6
7
STARBOARD ENGINE
GENERATOR
PORT ENGINE
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
120 Volt AC System
3
5
4
6
7
8
9
10
FORWARD
STARBOARD
2
1
2
3
4
5
DINETTE OUTLET
AFT BERTH OUTLET
BATTERY CHARGER
AIR CONDITIONER PUMP
WATER HEATER
1
6
7
8
9
10
HEAD OUTLET
GALLEY OUTLET
ALTERNATING CURRENT PANEL
SHORE POWER INLET
AIR CONDITIONER UNIT
55
Chapter 12: Electrical System
305 • Owner’s Manual Supplement
Bonding Harness
1
2
3
4
5
11
8
6
7
1
2
3
4
5
6
56
8
9
10
8
GENERATOR EXHAUST
PORT ENGINE
HEAD PICKUP
AIR CONDITIONER PICKUP
AIR CONDITIONER STRAINER
ZINC PLATE
7
8
9
10
11
STARBOARD ENGINE
BUSS BAR
GENERATOR
GENERATOR PICKUP
ALTERNATING CURRENT PANEL
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
Wire Diagrams
Engine Electrical System
57
Chapter 12: Electrical System
DC Electrical System
58
305 • Owner’s Manual Supplement
305 • Owner’s Manual Supplement
Chapter 12: Electrical System
AC Electrical System
59
305 • Owner’s Manual Supplement
Important Records
Selling Dealer
Key Numbers
Name Of Dealership
Ignition
Other
Address
Electronics
Phone/FAX/E-mail
Manufacturer
Model Name/Number
Sales Manager
Serial Number
Service Manager
Manufacturer
Model Name/Number
Engine(s)
Serial Number
Manufacturer
Model Name/Number
Port (or only) Engine Serial Number
Starboard Engine Serial Number
Oil Type/SAE
Quarts per Engine
Manufacturer
Filter Type
Propeller
Model Name/Number
Serial Number
Manufacturer
Model Name/Number
Serial Number
Manufacturer
Pitch
Model Number
60
305 • Owner’s Manual Supplement
Float Plan
Before going boating, fill out a copy of this float plan (or similar) and leave it with a reliable person whom you can
depend on to contact the Coast Guard or other rescue organization, if you do not return as scheduled.
Description of Boat
Persons on Board
Registration/Documentation Number
Length
Make
Hull Color
Full Name
Type
Age
Health
Phone Number
Trim Color
Full Name
Fuel Capacity
Engine Type
Number of Engines
Age
Health
Phone Number
Distinguishing Features
Full Name
Distinguishing Features
Age
Health
Phone Number
Operator of Boat
Full Name
Full Name
Age
Male or Female
Age
Health
Phone Number
Health
Full Name
Address
Age
Health
Phone Number
Address
Full Name
Phone/FAX/E-mail
Operator’s Experience
Age
Health
Phone Number
Full Name
Age
Health
Phone Number
Full Name
Age
Health
Phone Number
61
Float Plan
305 • Owner’s Manual Supplement
Survival Equipment
Trip Expectations
Marine Radio (Yes/No)
Type
Frequencies
Number of PFDs
Flares (Yes/No)
Mirror (yes or no)
Flashlight (Yes/No)
Food (Yes/No)
Smoke Signals (Yes/No)
Departing From
Departure Date
Departure Time
Stopover 1
Water (Yes/No)
Anchor (Yes/No)
Raft/Dinghy (Yes/No)
Arrive No Later Than: Date
Paddles (Yes/No)
EPIRB (Yes/No)
Other
Other
Other
Other
Arrive No Later Than: Time
Stopover 2
Arrive No Later Than: Date
Arrive No Later Than: Time
Vehicle Description
Stopover 3
Make
Model
Arrive No Later Than: Date
Color
Arrive No Later Than: Time
License Number
Stopover 4
Where is the Vehicle Parked?
Arrive No Later Than: Date
Arrive No Later Than: Time
Stopover 5
Arrive No Later Than: Date
Arrive No Later Than: Time
Stopover 6
Arrive No Later Than: Date
Arrive No Later Than: Time
Final Destination Port (If Different Than Home Port)
Arrive No Later Than: Date
Arrive No Later Than: Time
If not returned by the date and time listed above, call
the Coast Guard or other local authority.
Coast Guard Phone Number
Local Authority Phone Number
62
Owner’s Notes
Owner’s Notes
Part Number 1716976
Bayliner • P.O.Box 9029 • Everett, WA 98206
• 360-435-5571
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement