Bayliner 2006 285 Cruiser Owner Manual

Bayliner 2006 285 Cruiser Owner Manual
Engine Serial Number: _____________________________________
Hull Identification Number:__________________________________
Hull Identification Number
• The Hull Identification Number (HIN) is located on the
starboard side of the transom.
• Record the HIN (and the
engine serial numbers) in the
space provided above.
• Include the HIN with any correspondence or orders.
BOARDING
LADDER
HIN
LOCATION
© 2005 Bayliner Technical Publications. All rights reserved.
No part of this publication may be reproduced, stored in any retrieval system, or transmitted in any form by any means, electronic, mechanical,
photocopying, recording or otherwise, without prior written permission of Bayliner.
Printed in the United States of America.
General Notes
The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the
preparation of this document to assure its accuracy, Bayliner assumes no liability resulting from errors or omissions in this document, or from
the use of information contained herein.
Due to our commitment to product improvement, Bayliner reserves the right to make changes in the product design, specifications, and equipment at any time without notice or obligation. Illustrations and/or photos may show optional equipment.
All Bayliner products meet or exceed USCG (United States Coast Guard) and/or NMMA (National Marine Manufacturer’s Association) construction standards. Manufactured with 1,1,1 Trichloroethane, a substance which harms public health and environment during the manufacturing process by destroying ozone in the upper atmosphere.
Proprietary Rights
This document discloses subject matter in which Bayliner has proprietary rights. The information and design disclosed herein were originated
by and are the property of Bayliner. Neither receipt nor possession thereof confers or transfers any right to reproduce, copy, alter or disclose the
document or any part thereof, any information contained therein, or to construct boats or any item from it, except by written permission from or
written agreement with Bayliner. This document is to be returned upon request to Bayliner.
Part Number
1781921
CONTENTS
1
Chapter 1: Welcome Aboard!
1
1
1
1
2
2
Dimensions & Tank Capacities
Layout View
Dealer Service
Warranty Information
Boating Experience
Engine & Accessory Guidelines
2
3
3
4
5
Qualified Maintenance
Safety Standards
Special Care for Moored Boats
5
6
7
Engine & Accessory Literature
Propeller
Sacrificial Anode (Zinc)
Boat Lifting
Carbon Monoxide (CO)
7
7
CO Facts
Factors that Increase the Effects of
CO Poisoning
8 Where and How CO Can Accumulate
8 How to Protect Yourself and Others From CO
9 CO Checklists
9 CO Monitors
10 More Information
11
Chapter 2: Locations
11
Exterior Views
11 Hull Views
12 Forward Deck View
13 Helm
14
Component Locations
24
Chapter 3: Propulsion &
Related Systems
24
24
25
Engine
Bilge Blower System
Fuel System
26 Fuel Fill & Vent
26 Fuel Filters
26 Anti-siphon Valve
27
28
Quick Oil Drain System
Fire Suppression System (If Equipped)
29
Chapter 4: Controls & Gauges
29
29
29
30
30
Steering
Shift/Throttle Controls
Power Trim & Tilt
Trim Tabs
Gauges
30
30
30
30
Cleaning the Gauges
Gauge Fogging
Radio Transmission Interference
Fuel Gauge
31
Chapter 5: Navigation &
Communication Equipment
31
31
31
Compass
Depth Finder
VHF Radio (If Equipped)
32
Chapter 6: Plumbing
32
Bilge Pumps
35
49
Chapter 9: Convertible Seats,
Beds, & Tables
33 Bilge Pump Testing
34 Autofloat Switches
49
Dinette
Seawater Systems
50
Chapter 10: Lights
50
50
50
50
Care and Maintenance
Interior & Exterior Lights
Navigation Lights
Spotlight (If Equipped)
51
Chapter 11: Air Conditioning System
(If Equipped)
52
Chapter 12: Electrical System
35 Seacocks
35 Seawater Strainers
36
Freshwater System
37
37
38
38
39
Drain Systems
39
39
39
39
39
40
Freshwater System Winterization
Transom Shower (If Equipped)
Water Heater
Winterizing the Water Heater
Deck Drains
Gray Water Gravity Drains
Shower Sump Pump System
Sump Box Cleaning
Sump System Winterization
Marine Head & Holding Tank
53
40 Manual Flush Head with Holding Tank
41 Macerator (If Equipped)
42
Chapter 7: Deck Equipment
42
42
43
Cleats and Tow Eyes
Windlass (If Equipped)
Canvas
44 Vinyl Curtains (If Equipped)
45 Canvas Care
46 Clear Vinyl Care
47
Chapter 8: Appliances &
Entertainment Systems
47
47
48
Refrigerator
Audio Equipment
Alcohol/Electric Stove
12-Volt DC System
53
53
53
54
54
54
55
Batteries
Battery Switch
Fuses & Circuit Breakers
12-Volt DC Accessory Outlet
Alternator
Battery Charger
110-Volt AC System
56 Shore Power
57 Connecting to Shore Power
57 Parallel Switch (Only if Equipped with Dual
Shore Power)
58
Electrical Routings
58
59
60
61
62
Hull Harnesses
Deck Harnesses
110-Volt AC Electrical System Single Dockside
110-Volt AC Electrical System Dual Dockside
Engine Electrical System
63
Important Records
64
Float Plan
Hazard Boxes & Symbols
The hazard boxes and symbols shown below are used throughout this supplement to call attention to potentially dangerous situations which could lead to either personal injury or product damage. Read all warnings carefully and follow all safety instructions.
!
DANGER!
This box alerts you to immediate hazards which WILL cause severe personal injury or death if
the warning is ignored.
WARNING!
!
This box alerts you to hazards or unsafe practices which COULD result in severe personal
injury or death if the warning is ignored.
!
CAUTION
This box alerts you to hazards or unsafe practices which COULD result in minor personal
injury or cause product or property damage if the warning is ignored.
NOTICE
This box calls attention to installation, operation or maintenance information, which is important to proper operation but is not hazard related.
FIRE
HAZARD!
EXPLOSION
HAZARD!
FALLING
HAZARD!
NO OPEN
FLAME!
ROTATING
PROPELLER HAZARD!
ELECTRICAL
HAZARD!
HOT
HAZARD!
RUN BILGE BLOWERS
FOR 4 MINUTES!
CO POISONING
HAZARD!
285 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
• This Owner’s Manual Supplement provides information about your boat that is not covered in the Cruiser & Yacht
Owner’s Manual.
• Before using your boat, study this Owner’s Manual Supplement, the Cruiser & Yacht Owner’s Manual, and all
engine and accessory literature carefully.
• Keep this Owner’s Manual Supplement and the Cruiser & Yacht Owner’s Manual on your boat in a secure, yet
readily available place.
Dimensions & Tank Capacities
Overall
Length
Bridge
Clearance
Beam
Draft
(Hull)
Draft
(Maximum)
Fuel
Capacity
Freshwater
Capacity
Holding Tank
Capacity
29' 6"
9' 1"
9' 10"
1' 8"
3' 2"
102 Gallons
33 Gallons
20 Gallons
Layout View
Dealer Service
•
•
•
•
•
Your dealer is your key to service.
Ask your dealer to explain all systems before taking delivery of your boat.
Contact your dealer if you have any problems with your new boat.
If your dealer cannot help, call our customer service hotline: 360-435-8957 or send us a FAX: 360-403-4235.
Buy replacement parts from any authorized Bayliner dealer.
Warranty Information
• Bayliner offers a Limited Warranty on each new Bayliner purchased through an authorized Bayliner dealer.
• A copy of the Limited Warranty was included in your owner’s packet.
• If you did not receive a copy of the Limited Warranty, please contact your Bayliner dealer or call 360-435-8957
for a copy.
1
Chapter 1: Welcome Aboard!
285 • Owner’s Manual Supplement
Boating Experience
!
WARNING!
CONTROL HAZARD!
A qualified operator MUST be in control of your boat at ALL times. Do NOT operate your boat
while under the influence of alcohol or drugs.
If this is your first boat or if you are changing to a type of boat you are not familiar with, for your own comfort and
safety, obtain handling and operating experience before assuming command of this boat.
Take one of the boating safety classes offered by the U.S. Power Squadrons or the U.S. Coast Guard Auxiliary.
For more course information, including dates and locations of upcoming classes, contact the organizations directly:
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
• In Canada, for the CPS courses call 1-888-CPS-BOAT.
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
Outside the United States, your Bayliner dealer, national sailing federation, or local boat club can advise you of local
sea schools or competent instructors.
Engine & Accessory Guidelines
NOTICE
When storing your boat, please refer to your engine’s operation and maintenance manuals.
NOTICE
Certain modifications to your boat WILL result in cancellation of your warranty protection.
ALWAYS check with your dealer BEFORE making any modifications to your boat.
• Your boat’s engine and accessories were selected to provide optimum performance and service.
• Installing a different engine or other accessories may cause unwanted handling characteristics.
• Should you choose to install a different engine or accessories that will affect your boat’s running trim, have an
experienced marine technician perform a safety inspection and handling test before operating your boat again.
Engine & Accessory Literature
• The engine and accessories installed on your boat come with their own operation and maintenance manuals.
• Read these manuals before using the engine and accessories.
• Unless noted otherwise, all engine and accessory literature referred to in this supplement is included in your
owner’s packet.
2
285 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Propeller
!
CAUTION
ENGINE DAMAGE HAZARD!
The factory standard propeller may not be the best for your particular boat and load conditions. Refer to the engine manual for engine RPM ratings. The engine should reach, but not
exceed its full rated RPM when full-throttle is applied.
Immediately contact your local Bayliner dealer if:
• The engine cannot reach its full rated RPM when full-throttle is applied, or;
• The engine exceeds its full rated RPM when full-throttle is applied.
• Keep the propeller in good repair and at the correct pitch for your particular situation.
• A slightly bent or nicked propeller will adversely affect the performance of your boat.
Qualified Maintenance
!
WARNING!
To maintain the integrity and safety of your boat, allow ONLY qualified personnel to perform
maintenance on, or change, in any way, the:
• Steering system
• Propulsion system
• Engine control system
• Fuel system
• Environmental control system
• Electrical system
• Navigational system
• Failure to maintain your boat’s systems (listed in the warning above) as designed could violate the laws in your
jurisdiction and could expose you and other people to the danger of bodily injury or accidental death.
• Follow the instructions provided in the Cruiser & Yacht Owner’s Manual, this supplement, the engine owner’s
manual, and all accessory literature.
3
Chapter 1: Welcome Aboard!
285 • Owner’s Manual Supplement
Safety Standards
!
DANGER!
FALLING and ROTATING PROPELLER HAZARD!
• NEVER allow anyone to ride on parts of your boat NOT designed for
such use.
• Sitting on seat backs, lounging on the forward deck, bow riding, gunwale riding or occupying the transom platform while underway is especially hazardous and
WILL cause personal injury or death.
!
DANGER!
FALLING, ROTATING PROPELLER and CARBON
MONOXIDE POISONING HAZARD!
• NEVER allow anyone to occupy, or hang from, the
back deck or swim platform while the engine(s)
are running.
• Teak surfing, dragging, or water skiing within 20 feet
of a moving watercraft can be fatal.
!
DANGER!
DANGER
PERSONAL SAFETY HAZARD!
• ALWAYS secure the anchor and other loose objects BEFORE getting underway.
• The anchor and other items that are NOT properly secured can come loose when your boat
is moving and cause personal injury or death.
!
WARNING!
A wide variety of components used on this vessel contain or emit chemicals known to the State
of California to cause cancer and birth defects and other reproductive harm.
Examples Include:
• Engine and generator exhaust
• Engine and generator fuel, and other liquids such as coolants and oil, especially used
motor oil
• Cooking fuels
• Cleaners, paints, and substances used for vessel repair
• Waste materials that result from wear of vessel components
• Lead from battery terminals and from other sources such as ballast or fishing sinkers
To Avoid Harm:
• Keep away from engine, generator, and cooking fuel exhaust fumes.
• Wash exposed skin thoroughly with soap and water after handling the substances above.
• Your boat’s mechanical and electrical systems were designed to meet safety standards in effect at the time it
was built.
• Some of these standards were mandated by law, and all of them were designed to insure your safety and the safety
of other people, vessels and property.
Read this supplement, the Cruiser & Yacht Owner’s Manual, and all accessory instructions for important safety standards and hazard information.
4
285 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Special Care for Moored Boats
NOTICE
• To help seal the hull bottom and reduce the chance of gelcoat blistering while your boat is
moored, apply an epoxy barrier coating.
• The barrier coating should be covered with several coats of anti-fouling paint.
• Many states regulate the chemical content of bottom paints in order to meet environmental
standards. Check with your local dealer about recommended bottom paints, and about the
laws in effect in your area.
• Whether moored in saltwater or freshwater, your boat will collect marine growth on its hull bottom.
• This will detract from your boat’s beauty, greatly affect its performance, and may damage the gelcoat.
• Periodically haul your boat out of the water and scrub the hull bottom with a bristle brush and a solution of soap
and water.
Sacrificial Anode (Zinc)
NOTICE
• Do NOT paint between the zinc and the metal surface it contacts and do NOT paint over
the zinc.
• If the zinc is NOT bonded correctly, it will NOT provide protection.
Your boat is equipped with a sacrificial anode (zinc) to protect underwater metal parts from excessive deterioration.
Check the zinc regularly and replace it if it has deteriorated
more than 70%.
Many factors affect the rate at which the zinc deteriorates,
including:
• Water temperature
• Salinity
• Water pollution
• Stray electrical current
Stray electrical current from your boat, another boat, or the
dock may cause complete deterioration of the zinc in just a
few weeks. If there is rapid zinc deterioration, measure the
electrolytic corrosion around your boat with a corrosion
test meter.
NEW SACRIFICIAL ANODE
DETERIORATED SACRIFICIAL ANODE
5
Chapter 1: Welcome Aboard!
285 • Owner’s Manual Supplement
Boat Lifting
WARNING!
!
PERSONAL INJURY and/or PRODUCT or PROPERTY DAMAGE HAZARD!
• Lifting slings can slip on the hull, which could cause serious injury or death.
• Reduce the risk of sling slippage by ALWAYS securing the lifting slings together
BEFORE lifting.
!
WARNING!
PERSONAL INJURY and/or PRODUCT or PROPERTY DAMAGE HAZARD!
NEVER lift any boat using the cleats, or the bow and stern eyes.
!
WARNING!
PERSONAL INJURY and/or PRODUCT or PROPERTY DAMAGE HAZARD!
• Water in the bilge can shift and change the balance of the load.
• If water is present in the bilge, pump or drain the water out of the bilge areas BEFORE lifting your boat.
!
CAUTION
PRODUCT or PROPERTY DAMAGE HAZARD!
When lifting any boat, ALWAYS use a spreader bar. The spreader bar MUST be equal to the
width of your boat at each lifting point.
LIFTING SLING LABELS
(TYPICAL PORT & STARBOARD)
44"
167"
• Always follow the lift equipment’s instructions and requirements.
• When lifting your boat, always position the lifting slings at the port and starboard lifting sling label positions as
shown in the illustration.
6
285 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Carbon Monoxide (CO)
!
DANGER!
• Carbon monoxide gas (CO) is colorless, odorless, tasteless, and
extremely dangerous.
• ALL engines, generators, and fuel burning appliances produce CO
as exhaust.
• Prolonged exposure to low concentrations or very quick exposure to high
concentrations WILL cause BRAIN DAMAGE or DEATH.
• Teak surfing, dragging, or water skiing within 20 feet of a moving watercraft can be fatal.
CO Facts
• CO poisoning causes a significant number of boating deaths each year.
• Called the "silent killer", CO is an extremely toxic, colorless, odorless and tasteless gas.
• CO can harm or even kill you inside or outside your boat.
• CO can affect you whether you’re underway, moored, or anchored.
• CO symptoms are similar to seasickness or alcohol intoxication.
• CO can make you sick in seconds. In high enough concentrations, even a few breaths can be fatal.
• Breathing CO blocks the ability of your blood to carry oxygen.
• The effects are cumulative. Even low levels of exposure can result in injury or death.
Factors that Increase the Effects of CO Poisoning
• Age
• Smokers or people exposed to high concentrations of cigarette smoke
• Consumption of alcohol
• Lung disorders
• Heart problems
• Pregnancy
7
Chapter 1: Welcome Aboard!
285 • Owner’s Manual Supplement
Where and How CO Can Accumulate
Stationary Conditions That Increase CO Accumulations Include:
A. Using engine, generator, or other fuel burning device when boat is moored in a confined space.
B. Mooring too close to another boat that is
using its engine, generator, or other fuel
burning device.
To correct stationary situations A and/or B:
• Close all windows, portlights and hatches.
• If possible, move your boat away from source of CO.
Running Conditions That Increase CO Accumulations Include:
C. Running boat with trim angle of bow too high.
D. Running boat without through ventilation
(station wagon effect).
To correct running situations C and/or D:
• Trim bow down.
• Open windows and canvas.
• When possible, run boat so that prevailing winds help dissipate exhaust.
How to Protect Yourself and Others From CO
• Know where and how CO may accumulate in and around your boat (see above).
• Always maintain fresh air circulation throughout your boat.
• Know where your engine and generator exhaust outlets are located and keep everyone away from these areas.
• Never sit on, or hang onto, the back deck or swim platform while the engine is running.
• Never enter the areas under swim platforms where exhaust outlets are located.
• Although CO can be present without the smell of exhaust fumes, if exhaust fumes are detected on your boat, take
immediate action to dissipate these fumes.
• Treat symptoms of seasickness as possible CO poisoning. Get the person into fresh air immediately. Seek medical
attention—unless you’re sure it’s not CO.
• Install and maintain CO monitors inside your boat. Never ignore any alarm. Replace monitors as recommended by
the monitor manufacturer.
• Follow the checklists provided on the next page.
• Get a Vessel Safety Check.
For information on how to get a free VESSEL SAFETY CHECK, visit www.vesselsafetycheck.org or contact your
local U.S. Coast Guard Auxiliary or United States Power Squadrons®.
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
8
285 • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
CO Checklists
Trip Checklist
❏ Make sure you know where the exhaust outlets are located on your boat.
❏ Educate all passengers about the symptoms of CO poisoning and where CO may accumulate.
❏ When docked, or rafted with another boat, be aware of exhaust emissions from the other boat.
❏ Listen for any change in exhaust sound, which could mean an exhaust component failure.
❏ Test the operation of each CO monitor by pressing the test button.
Monthly Checklist
❏ Make sure all exhaust clamps are in place and secure.
❏ Look for exhaust leaking from exhaust system components. Signs include rust and/or black streaking, water
leaks, or corroded or cracked fittings.
❏ Inspect rubber exhaust hoses for burned, cracked, or deteriorated sections. All rubber hoses should be pliable and
free of kinks.
Annual Checklist
Have a Qualified Marine Technician:
❏ Replace exhaust hoses if cracking, charring, or deterioration is found.
❏ Ensure that your engines and generators are properly tuned, and well maintained.
❏ Inspect each water pump impeller and the water pump housing. Replace if worn. Make sure cooling systems are
in working condition.
❏ Inspect all metallic exhaust components for cracking, rusting, leaking, or loosening. Make sure they check the
cylinder head gasket, exhaust manifold, water injection elbow, and the threaded adapter nipple between the manifold and the elbow.
❏ Clean, inspect, and confirm proper operation of the generator cooling water anti-siphon valve (if equipped).
CO Monitors
NOTICE
• The stereo memory and CO monitors place a small, but constant drain on the battery.
• If your boat will be unattended for an extended amount of time, plug into shore power with
the battery charger turned On.
• Do not disconnect the CO monitors.
• Read the manufacturer’s instructions for your CO monitors. If you did not get the manufacturer’s instructions,
call (800) 383-0269 and they will be mailed to you.
If your boat is not equipped with a CO monitor, consider purchasing one from your dealer or marine supply store.
9
Chapter 1: Welcome Aboard!
285 • Owner’s Manual Supplement
More Information
For more information about how you can prevent carbon monoxide poisoning on recreational boats and other ways to
boat more safely, contact:
United States Coast Guard
Office of Boating Safety (G-OPB-3)
2100 Second Street SW
Washington, DC 20593
www.uscgboating.org
1-800-368-5647
National Marine Manufacturers
Association (NMMA)
200 East Randolph Drive
Suite 5100
Chicago, IL 60601-9301
www.nmma.org
312-946-6200
American Boat & Yacht Council, Inc.
(ABYC)
3069 Solomon’s Island Road
Edgewater, MD 21037-1416
www.abycinc.org
410-956-1050
For information on how to get a free VESSEL SAFETY CHECK, visit www.vesselsafetycheck.org or contact your
local U.S. Coast Guard Auxiliary or United States Power Squadrons®.
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
10
285 • Owner’s Manual Supplement
Chapter 2: Locations
Exterior Views
Hull Views
HOLDING
TANK VENT
STORAGE
DRAIN
PORTLIGHT
FRESHWATER
TANK VENT
FUEL TANK VENT
STARBOARD HULLSIDE
BOW
EYE
COCKPIT
DRAINS
AFT BILGE
PUMP DRAIN
FORWARD BILGE
PUMP DRAIN
SHOWER SUMP
PUMP DRAIN
HEAD SINK
DRAIN
PORT HULLSIDE
ROPE
LOCKER
DRAIN
AIR CONDITIONER
THRU-HULL DRAINS
(IF EQUIPPED)
GALLEY
DRAIN
COCKPIT
DRAINS
BOARDING LADDER
TRANSOM
TRIM TAB
TRIM TAB
STERN EYE
STERN EYE
BILGE DRAIN PLUG
MACERATOR OVERBOARD
DISCHARGE (IF EQUIPPED)
11
Chapter 2: Locations
285 • Owner’s Manual Supplement
Forward Deck View
DECK HATCHES
BOW HATCH
WINDSHIELD
WIPER
CLEAT
(TYPICAL PORT
& STARBOARD)
WINDLASS
FOOT
SWITCHES
(IF EQUIPPED)
WINDLASS
(IF EQUIPPED)
PORT BOW
LIGHT
STARBOARD
BOW LIGHT
ANCHOR
HORN
ROLLER
SPOTLIGHT
(IF EQUIPPED)
Aft Deck View
GRAB RAIL
FRESHWATER FILL
DECK FITTING
TRANSOM
STORAGE
LOCKER
FUEL FILL
DECK FITTING
CLEAT
HOLDING TANK PUMPOUT DECK FITTING
GRAB RAIL
12
285 • Owner’s Manual Supplement
Chapter 2: Locations
Helm
NOTE: TYPICAL HELM LAYOUT SHOWN.
ACTUAL LAYOUT MAY VARY DEPENDING
ON ENGINE AND ACCESSORY OPTIONS.
GAUGE PANEL
TEMPERATURE
TACHOMETER
DEPTH FINDER
OIL
(IF EQUIPPED) PRESSURE
VOLTMETER
TRIM &
TILT
SPEEDOMETER
FUEL
STEREO REMOTE
(IF EQUIPPED)
WINDLASS SWITCH
(IF EQUIPPED)
ACCESSORY
SWITCHES
TRIM TAB
SWITCHES
12-VOLT DC OUTLET
IGNITION
VHF RADIO
(IF EQUIPPED)
12-VOLT DC PUSH-TORESET CIRCUIT BREAKERS
MACERATOR SWITCHES
(IF EQUIPPED)
13
Chapter 2: Locations
285 • Owner’s Manual Supplement
Component Locations
12-Volt DC Accessory Outlet: Located at the helm.
12-Volt DC Circuit Breakers:
• The 12-volt DC push-to-reset circuit breakers are
located at the helm.
12-VOLT DC
OUTLET
12-VOLT DC PUSH-TORESET CIRCUIT BREAKERS
• The 12-volt DC main circuit breaker switch and
standby-load push-to-reset circuit breakers are located
on the battery switch panel inside the transom storage
locker.
12-VOLT DC STAND-BY
LOAD PUSH-TO-RESET
CIRCUIT BREAKERS
12-VOLT DC
MAIN CIRCUIT
BREAKER SWITCH
110-Volt AC Master Panel: Located on the
aft berth cabinet above the hanging locker.
AC MASTER PANEL
14
285 • Owner’s Manual Supplement
Chapter 2: Locations
Air Conditioner (If Equipped): Located in the aft port
storage locker under the v-berth cushion.
AIR CONDITIONER
AIR CONDITIONER
CONTROL PANEL
Air Conditioner Control Panel (If Equipped): Located
on the aft end of the v-berth bunk.
Air Conditioner Seawater
Intake Seacock (If Equipped):
Located on the port aft side of
the engine room.
INTAKE
SEACOCK
Batteries: Located in the port forward corner of the
engine room.
BATTERIES
BATTERY CHARGER
Battery Charger: Located on the port forward wall of the
engine room.
15
Chapter 2: Locations
285 • Owner’s Manual Supplement
Battery Switch Panel: Located inside the transom
storage locker on the port side.
BATTERY SWITCH
PANEL
Bilge Pumps (2 Total):
• The aft bilge pump is located in the
engine room bilge, forward of the
engine.
• The forward bilge pump is located in
the bilge under the entry steps. Access
by removing the bottom entry step
riser hatch cover.
FORWARD
BILGE PUMP
STEP RISER
HATCH COVER
AFT BILGE
PUMP
16
285 • Owner’s Manual Supplement
Chapter 2: Locations
CO Monitors (2 Total):
• One is located on the ceiling above the aft end of
the dinette.
CO MONITOR
• One is located on the ceiling in the aft berth.
CO MONITOR
Depth Finder Transducer: Located in the engine room
bilge, forward of the engine.
TRANSDUCER
17
Chapter 2: Locations
285 • Owner’s Manual Supplement
Freshwater Pump:
• Located under the entry steps.
• Access by removing the bottom entry step riser
hatch cover.
FRESHWATER
PUMP
STEP RISER
HATCH COVER
Freshwater Pump Switch: Located at the
forward end of the lower galley cabinet.
FRESHWATER
PUMP SWITCH
Freshwater Tank:
• Located under the entry steps.
• Access by removing the bottom entry step riser
hatch cover.
FRESHWATER
TANK
STEP RISER
HATCH COVER
18
285 • Owner’s Manual Supplement
Chapter 2: Locations
Freshwater Fill Deck Fitting (marked WATER):
Located on the starboard side of the deck, just forward of the ventilation louver.
FRESHWATER FILL
DECK FITTING
Fuel Fill Deck Fitting (marked GAS): Located on the
starboard aft corner of the deck.
FUEL FILL
DECK FITTING
Fuel Tank: Located in the engine room.
FUEL TANK
19
Chapter 2: Locations
285 • Owner’s Manual Supplement
Holding Tank: Located on the starboard forward side of the engine
room.
HOLDING TANK
Holding Tank Pump-out Deck Fitting (marked WASTE): Located on
the starboard aft corner of the aft
deck, next to the transom door.
HOLDING TANK PUMPOUT DECK FITTING
Macerator Underwater Discharge Seacock (If
Equipped): Located on the starboard aft wall of
the engine room.
MACERATOR DISCHARGE
SEACOCK
20
285 • Owner’s Manual Supplement
Chapter 2: Locations
Marine Head (Electric) Seawater Intake Seacock:
• Located in the bilge under the entry steps.
• Access by removing the bottom entry step riser
hatch cover.
MARINE HEAD
INTAKE SEACOCK
STEP RISER
HATCH COVER
Shore Power Inlet(s) (If
Equipped): Located on the port
aft deck.
SHORE POWER
INLET(S)
Shower Drain Sump Pump Box:
• Located under the entry steps.
• Access by removing the bottom entry step riser
hatch cover.
SHOWER
DRAIN PUMP
STEP RISER
HATCH COVER
21
Chapter 2: Locations
285 • Owner’s Manual Supplement
Spotlight (If Equipped): Located on the bow.
SPOTLIGHT
Spotlight Control Panel (If Equipped): Located at
the helm.
SPOTLIGHT
CONTROL
PANEL
Trim & Tilt Pump: Located in the port aft corner
of the engine room.
TRIM &
TILT PUMP
22
285 • Owner’s Manual Supplement
Chapter 2: Locations
Trim Tab Hydraulic Fluid Reservoir:
Located in the port aft corner of the
engine room.
HYDRAULIC FLUID
RESERVOIR
Water Heater: Located on the port side of the
engine room.
WATER
HEATER
23
285 • Owner’s Manual Supplement
Chapter 3: Propulsion & Related Systems
Engine
Read the engine operation and maintenance manuals before starting or working on the engine.
Bilge Blower System
!
WARNING!
FIRE and EXPLOSION HAZARD!
Fuel vapors can explode! BEFORE starting the engine:
1. Check the bilge areas for fuel vapors or leaking fuel. If you see leaking fuel or smell
fuel vapors:
a. Do NOT start the engine, do NOT turn On any electrical devices, extinguish ALL ciga-
rettes, cigars, and other sources of flame or ignition.
b. Get everyone off your boat.
c. Get trained help to find and fix the problem.
2. Run the bilge blower for at least four minutes prior to engine starting, electrical system
maintenance, or activation of electrical devices.
• If you smell fuel vapors and the engine is already running;
a. Shut Off the engine and turn Off ALL electrical devices
b. Extinguish ALL cigarettes, cigars, and other sources of flame or ignition.
c. Get trained help to find and fix the problem.
• NEVER obstruct or change the bilge blower system.
• The bilge blower removes explosive fumes from
the engine and bilge areas.
• Fresh air is drawn into the engine and bilge areas
through the vents.
To make sure the engine and bilge areas are
properly ventilated:
• Use the "sniff test" to check the engine and bilge
areas for fuel vapors before starting the engine.
• Always run the bilge blower for at least four minutes before starting the engine.
• Continue to run the blower until your boat has
reached cruising speed.
• Always run the blower when running the boat
below cruising speed.
BLOWER HOSES
24
BLOWER
285 • Owner’s Manual Supplement
Chapter 3: Propulsion & Related Systems
Fuel System
!
WARNING!
FIRE, EXPLOSION, and OPEN FLAME HAZARD!
• It is very important that the fuel system be inspected thoroughly the first time it is filled and
at each subsequent filling.
• The fueling instructions in the Cruiser & Yacht Owner’s Manual and the fuel recommendations in the engine operation manual MUST be followed.
!
CAUTION
Avoid the storage or handling of gear near the fuel lines, fittings and tank.
NOTICE
Carefully read the fuel section of both the Cruiser & Yacht Owner’s Manual and the engine
operation manual, paying special attention to the subject of fuel recommendations.
FUEL TANK
FUEL FEED LINE
AFT
INLINE FUEL FILTER
(MPI ENGINE ONLY)
ENGINE
ROOM
FUEL TANK
VENT FITTING
TO FUEL FILL
DECK FITTING
25
Chapter 3: Propulsion & Related Systems
285 • Owner’s Manual Supplement
Fuel Fill & Vent
• The fuel fill deck fitting is marked GAS.
• If you have problems filling the fuel tank, see if the fuel fill hose or fuel tank vent hose is kinked or collapsed.
• If there are no visible signs of a problem, contact your local dealer.
Fuel Filters
• The fuel pickup tube, located inside the fuel tank, is equipped with a fine mesh screen filter.
• If your boat features an MPI engine, there may be an inline fuel filter on the fuel line.
• Also, when supplied by the engine manufacturer, a fuel filter is installed on the engine.
• Periodically replace the fuel filters to make sure they remain clean and free of debris.
• Talk to your selling dealer or local marina about fuel additives that help prevent fungus or other buildup in your
fuel tank.
Anti-siphon Valve
NOTICE
• If an engine running problem is diagnosed as fuel starvation, check the anti-siphon valve.
• If the valve is stuck or clogged, ONLY change or replace it while the engine is Off.
• NEVER run the engine with the anti-siphon valve removed, except in an emergency.
•
•
•
•
26
The anti-siphon valve is a vital fuel system part.
If the fuel line ruptures, this valve will prevent the fuel from siphoning from the tank.
The valve is located on the fuel tank, where the fuel feed line attaches to the tank.
The valve is spring loaded and is opened by fuel pump vacuum.
285 • Owner’s Manual Supplement
Chapter 3: Propulsion & Related Systems
Quick Oil Drain System
The quick oil drain hose was attached to the engine oil pan at the factory. However, some minor assembly is still
needed before you can use this system.
How to install the quick oil drain system:
1. Unscrew the factory installed
bilge plug from the bilge drain
(A). Keep the factory bilge plug
on your boat as a spare.
2. Unclip the quick oil drain assembly from the wire loop (B) on
the engine.
3. Un-clip the draw cord section
(C) from the draw cord
section (D).
4. Thread the draw cord section
(D), the oil drain plug (E), and
the oil drain hose (F) through the
bilge drain (A).
5. Adjust the hose stop clamp (G)
so that no more than 12 inches
of hose, including the oil drain
plug, can extend out of the
bilge drain (A).
6. Re-clip the draw cord section (C)
to the draw cord section (D).
7. Push the oil drain hose, oil drain
plug, and both sections of the
draw cords through the bilge
drain and into the bilge area.
8. Screw the oil drain bilge plug
(H) into the bilge drain (A) and
tighten firmly.
QUICK OIL DRAIN SYSTEM
ENGINE
OIL PAN
TRANSOM
F
D
H
E
FACTORY
INSTALLED
C
BILGE
A
G
B
To drain the engine oil:
1. Remove your boat from
the water.
2. Unscrew the bilge plug.
3. Pull the draw cord until the oil drain plug and the oil drain hose slide out of the bilge drain.
4. Place the end of the oil drain hose into a suitable container.
5. Unscrew the oil drain plug and drain the engine oil.
6. Replace the oil drain plug.
7. Push the drain hose back into the bilge.
8. Replace the bilge plug and tighten firmly.
Always dispose of waste oil in accordance with local regulations.
27
Chapter 3: Propulsion & Related Systems
285 • Owner’s Manual Supplement
Fire Suppression System (If Equipped)
• The fire suppression
system is designed to
extinguish engine
room fires.
• Before using your
boat for the first time,
read the fire suppression system’s instruction and maintenance
manual and follow all
warnings.
• The system will discharge automatically
whenever direct heat
from a fire is detected
in the engine room.
• The system can be
discharged manually
by pulling the T-handle (labeled FIRE) at
the helm.
• The system can only
be discharged once.
• After the system is
discharged, it must be
refilled and refurbished before it can be
used again.
FIXED FIRE BOTTLE
FIRE INDICATOR
LIGHT
28
T-HANDLE
285 • Owner’s Manual Supplement
Chapter 4: Controls & Gauges
Steering
•
•
•
•
Your boat features a power-assisted rack-and-pinion steering system.
For information about the power-assist fluid reservoir, refer to the engine operation and maintenance manual.
Boat steering is not self-centering.
Refer to the engine manual for more steering system details.
Shift/Throttle Controls
!
WARNING!
LOSS OF CONTROL HAZARD!
Improper maintenance of the shift/throttle hardware may cause a sudden loss of control!
Read all of the information about the shift/throttle controls in the shift/throttle manual, the engine operation manual,
and the Cruiser & Yacht Owner’s Manual.
Power Trim & Tilt
• The stern drive on your boat is equipped with power trim and tilt.
• Trim and tilt instructions are provided in the engine operation manual and the shift/throttle manual.
29
Chapter 4: Controls & Gauges
285 • Owner’s Manual Supplement
Trim Tabs
• Before using
the trim tabs,
read the trim
tabs’ owner’s
manual.
• The trim tabs
TRANSOM
are controlled
TRIM TAB
by two rocker
SWITCHES
switches at
the helm.
TRIM TAB
• Check and
(TYPICAL)
refill the trim
tab hydraulic
fluid reservoir as
directed in
the trim tabs’
owner’s manual. For the location of the fluid reservoir, see the Component Locations section of Chapter 2 in
this supplement.
Gauges
Cleaning the Gauges
!
CAUTION
PRODUCT or PROPERTY DAMAGE HAZARD!
• Use only mild soap and water to clean the gauge lenses and bezels.
• Use of other cleaners, including common window cleaning solutions, may cause the lenses
to crack.
• Lenses cracked in this manner will NOT be covered by our warranty.
Gauge Fogging
• Moisture may occasionally find its way into the gauges causing lens fogging.
• Turning On the gauge lights will help dry the lenses.
• Fogging will not harm the gauges.
Radio Transmission Interference
VHF or other radio transmissions may cause brief erratic readings on the tachometer. This will not damage the
tachometer gauge or affect its accuracy when not transmitting.
Fuel Gauge
It is normal for the pointer on your fuel gauge to bounce as fuel sloshes back and forth in the fuel tank.
30
285 • Owner’s Manual Supplement
Chapter 5: Navigation & Communication Equipment
Read the manuals for all navigation & communication equipment before using these systems.
Compass
NOTICE
• Compass accuracy can be affected by many factors.
• Have a qualified technician calibrate your compass.
• Make sure the technician gives you a deviation card which shows the corrections to apply in
navigational calculations.
• Keep a copy of the deviation card at the helm.
Depth Finder
!
WARNING!
• Do NOT use the depth finder as a navigational aid to prevent collision, grounding, boat
damage or personal injury.
• When your boat is moving, submerged objects will NOT be seen until they are already
under your boat.
• Bottom depths may change too quickly to allow time for your boat to react.
• If you suspect shallow water or submerged objects, run your boat at very slow speeds.
VHF Radio (If Equipped)
• Your boat may include a VHF (Very High Frequency) radio.
• As permitted by the FCC (Federal Communications Commission), the VHF radio can be used to access weather
reports, summon assistance, or contact other vessels.
• Contact the FCC for licensing, rules and regulations concerning VHF radio usage.
31
285 • Owner’s Manual Supplement
Chapter 6: Plumbing
Bilge Pumps
NOTICE
Discharge of oil, oil waste, or fuel into navigable waters is prohibited by law. Violators are subject to legal action by the local authorities.
AFT BILGE PUMP
& AUTOFLOAT SWITCH
THRU-HULLS
FORWARD BILGE PUMP
& AUTOFLOAT SWITCH
• Your boat has two bilge pumps for pumping water out of the bilge.
• The autofloat switches, mounted next to the bilge pumps, will turn On the bilge pumps if bilge water rises above a
preset level.
• You can also turn On the bilge pumps yourself using the switches at the helm.
• The bilge pumps are wired directly to the battery. Unless the battery is dead, the bilge pump system should work
even when your boat is unattended.
32
285 • Owner’s Manual Supplement
Chapter 6: Plumbing
Bilge Pump Testing
• The bilge pumps are vital to the safety of your boat.
• Test the bilge pumps often.
1. One at a time, turn On each bilge pump switch at the helm.
2. Make sure that water in the bilge is pumped overboard.
• If there is water in the bilge and the pump motor is running but not pumping, inspect the discharge hose for a kink
or collapsed area.
• If the discharge hose looks okay, check the bilge pump housing for clogging debris (see below).
Checking for clogging debris:
1. Remove the pump motor from the
PUMP
housing:
MOTOR
TAB
"O" RING
HOUSING
a. Lift the tab while rotating the
fins counter-clockwise.
b. Lift out the pump motor.
c. Clear the housing of debris.
2. Reinstall the pump motor:
a. Make sure the "O" ring is properly seated.
b. Coat the "O" ring with a light
film of vegetable or mineral oil.
c. Align the cams on either side of
CAM (TYPICAL
SLOT (TYPICAL
FIN
OPPOSITE SIDE)
OPPOSITE SIDE)
the pump motor with the slots
on the housing.
d. Press the pump motor into the housing while twisting clockwise.
3. Check the reinstallation by trying to twist the fins counter-clockwise without lifting the tab; the pump motor
should stay in place.
33
Chapter 6: Plumbing
285 • Owner’s Manual Supplement
Autofloat Switches
• The autofloat switches turn the bilge pumps On when water rises above a preset level.
• Test each autofloat switch often.
Autofloat switch testing:
AUTOFLOAT SWITCH
TESTING
1. Lift the autofloat switch test button to turn On the bilge pump.
• If the pump does not turn On, check
the push-to-reset circuit breaker.
• If the circuit breaker is good, but
the switch still does not work, it
may mean the switch is bad or, the
battery is dead.
2. After testing, push the test button
all the way down to reset auto
mode.
TEST BUTTON
LIFT TEST BUTTON UP
(BILGE PUMP SHOULD TURN ON)
!
PUSH TEST BUTTON DOWN
(BILGE PUMP SHOULD TURN OFF)
CAUTION
When the test is completed on each float switch, you MUST push the test button ALL THE
WAY DOWN to reset auto mode!
34
285 • Owner’s Manual Supplement
Chapter 6: Plumbing
Seawater Systems
Seacocks
WARNING!
!
FLOODING and SWAMPING HAZARD!
• Close the seacock(s) when leaving your boat unattended for any length of time.
• If a seacock is left open, a hose failure could flood the bilge, swamp the battery and the
engine, and even sink your boat.
!
CAUTION
SYSTEM DAMAGE HAZARD!
• BEFORE using any system that has a seacock, make sure that the system’s seacock is Open.
• Inspect and lubricate all seacocks annually.
Thru-hull inlet or outlet fittings near or below the waterline feaSEACOCK & THRU-HULL
ture seacock valves. You can close a seacock to stop water entry:
COMPONENTS (TYPICAL)
• If the hose connected to the seacock fails, or;
90 DEGREE
SEACOCK (TYPICAL)
• To work on equipment served by the seacock.
SEACOCK
LEVER
SEACOCK GASKET
Seacocks are used on your boat in seawater intake or liquid-discharge systems including, but not limited to:
HULL
THRU-HULL INTAKE
• Air conditioner (if equipped)
SECTION
STRAINER
• Marine head (toilet)
Before using any system with a seacock, make sure the seacock is Open and stays Open until the system is shut Off.
Seawater Strainers
!
CAUTION
FLOODING HAZARD!
• BEFORE taking apart a seawater strainer for cleaning or other maintenance, Close the
seacock that sends seawater to that strainer.
• Failure to close the seacock before taking apart the seawater strainer may allow large
amounts of water to flood the bilge, which could swamp the batteries and the engines, and
even sink your boat.
• Keep the seacock Closed until the seawater strainer is completely reassembled.
SYSTEM DAMAGE HAZARD!
• After putting the seawater strainer back together, make sure that the seacock valve is Open
BEFORE using the component/system.
• Seawater strainers are used to filter incoming seawater in some seawater intake systems. NOTE: Not all seawater
intake systems have seawater strainers.
• If equipped, the seawater strainer is located near the seawater intake system’s seacock.
• Check the strainers for leaks and/or debris every time you use your boat.
• Refer to the seawater strainer instruction sheet for cleaning and maintenance information.
35
Chapter 6: Plumbing
285 • Owner’s Manual Supplement
Freshwater System
!
WARNING!
• ONLY use safe drinking (potable) water in your boat’s freshwater system.
• ONLY use FDA approved "drinking water safe" hoses when filling the freshwater tank.
• NEVER use common garden hoses for drinking water.
• Read the Freshwater System
section in the Cruiser & Yacht
Owner’s Manual.
• The freshwater fill deck fitting
is marked WATER.
• Pressurize the freshwater system by either turning On the
freshwater pump switch (the
battery switch must also be
On).
• For the location of the freshwater pump switch, see the Component Locations section of
Chapter 2 in this supplement.
• Turn Off the freshwater pump
switch when your boat is not in
use or when the freshwater tank
is empty.
• Inspect and clean the freshwater filter often (the filter is
located on the freshwater
pump).
• If your boat is to be left unattended for a long period of
time, pump the freshwater tank
dry to prevent stored water
from becoming stagnant and
distasteful.
• If the freshwater system needs
to be disinfected, ask your
dealer about treatments available for your boat’s system.
FRESHWATER
TANK
GALLEY
FAUCET
HEAD
FAUCET
FRESHWATER
PUMP
FRESHWATER FILL
DECK FITTING
WATER
HEATER
TRANSOM SHOWER
(IF EQUIPPED)
HOT WATER
COLD WATER
36
FRESHWATER
TANK VENT
285 • Owner’s Manual Supplement
Chapter 6: Plumbing
Freshwater System Winterization
1. Turn Off the water heater breaker switch.
NOTE: Tag or Mark the water heater breaker switch to prevent it from being turned On while the water heater
tank is empty.
2. Turn On the freshwater pump switch.
3. Open all of the faucets and showers and let the freshwater system drain completely.
4. Turn Off the freshwater pump switch.
All of the remaining water must be removed from the water lines. There are two ways to remove the remaining water
from the lines:
• Compressed Air
• Gravity Draining
Compressed Air
!
CAUTION
FRESHWATER SYSTEM DAMAGE HAZARD!
• A faucet must be open when compressed air is blown through the freshwater system.
• NEVER blow compressed air through the water system when ALL of the faucets are Closed.
You must have an air compressor with an air hose and
an air nozzle.
1. Remove the water line from the outlet side of the
freshwater pump (opposite side from filter).
2. Open the faucet that is furthest away from the freshwater pump.
3. Place the air nozzle against the end of the just
removed water line and blow air through the system.
4. When water stops coming out of the faucet, stop the
air and Close the faucet.
5. One at a time, repeat this process on all faucets and
showers.
TYPICAL VIEW
NOTE: LOCATION OF TEE FITTING
& DRAIN PLUG MAY VARY
DRAIN PLUG
INLET SIDE
WATER LINE
FILTER
FRESHWATER
PUMP
Gravity Draining
1. Open all faucets and showers.
2. Remove the drain plug from the tee fitting on the
freshwater tank.
3. When the water has stopped draining from the
freshwater tank and the water lines, replace the
drain plug.
OUTLET SIDE
WATER LINE
FRESHWATER TANK
TEE FITTING
Transom Shower (If Equipped)
• Read the manufacturer’s instructions before using the transom shower for the first time.
• The freshwater pump switch must be turned On before using the transom shower.
37
Chapter 6: Plumbing
285 • Owner’s Manual Supplement
Water Heater
!
WARNING!
SCALDING HAZARD!
Water heated by the water heater can be hot enough to scald the skin.
!
CAUTION
WATER HEATER DAMAGE HAZARD!
• Do NOT turn On the water heater circuit breaker on the 110-volt AC master panel until the
water heater tank is COMPLETELY filled with water.
• The tank is full if water flows from the tap when the hot water is turned On in the galley.
• Even brief water heater operation with a dry tank WILL damage the heating elements.
• Warranty replacements will NOT be made on elements damaged in this manner.
• Drain the water heater and turn the power Off when the chance of freezing exists (see the
winterizing instructions below).
NOTICE
If 110-volt AC power is being provided by shore power, but the water heater is not working:
• Make sure the water heater circuit breaker on the 110-volt AC master panel is switched On.
• If the circuit breaker is On, but the water heater is still not working, ask your dealer how
to check the push-to-reset circuit breaker located on the water heater.
• Read the water heater instruction manual and heed the warnings above.
• The water heater is connected to the 110-volt AC power system.
• To heat the water, turn On the water heater circuit breaker on the 110-volt AC master panel.
Winterizing the Water Heater
NOTICE
The freshwater system MUST be drained BEFORE winterizing the water heater (see the
Freshwater System Winterization Instructions on the previous page).
1. Turn Off the water heater breaker.
2. Disconnect the hose (A) attached to the pressure
relief valve (B).
3. If there is any water in this hose, drain it into the
bilge or into a bucket.
4. Open the pressure relief valve (B).
5. Open the drain valve (C).
• Leave the pressure relief and drain valves Open until
you fit out your boat after storage.
38
B
A
C
285 • Owner’s Manual Supplement
Chapter 6: Plumbing
Drain Systems
Deck Drains
• Water on the deck is drained overboard through the deck drains.
• Keep the deck drains free of debris.
Gray Water Gravity Drains
The sinks are above the waterline and are gravity drained overboard
Shower Sump
Pump System
• The shower drains
into sump pump
box.
• The sump pump
box has an autofloat switch.
• When the drain
water rises to a preset level, the autofloat switch turns
On the sump
pump, and the
drain water is
pumped overboard.
THRU-HULL
DRAIN
SHOWER
DRAIN
SUMP
PUMP BOX
Sump Box Cleaning
C
B
Periodically clean the sump box (A), filter, and pump as follows:
1. Remove the cover screws (B) and the cover (C).
2. Remove any debris from the box and the filter.
3. Clean the sump pump as outlined in the Bilge Pump section of
this chapter.
Sump System Winterization
Drain the sump pump system in the months when not in use.
1. Disconnect and drain all lines to the unit.
2. Remove the screws from the mounting feet (D) and drain
the system.
3. Reinstall the screws in the mounting feet and reconnect the system.
A
D
39
Chapter 6: Plumbing
285 • Owner’s Manual Supplement
Marine Head & Holding Tank
NOTICE
Check with local authorities for regulations regarding the legal use of marine head systems.
Manual Flush Head with Holding Tank
!
WARNING!
FLOODING and SWAMPING HAZARD!
• Close the seawater intake seacock when leaving your boat unattended for any length of
time.
• If the seacock is left open, a hose failure could flood the bilge, swamp the batteries and the
engine, and even sink your boat.
• Before using this system, read the marine head’s
operation and maintenance manual.
• Look at the side of the holding tank to check the
content level.
• The dockside pump-out deck fitting is marked
WASTE.
• Empty the holding tank at every opportunity.
INTAKE
SEACOCK
MARINE HEAD
Using the Marine Head
1. Open the head’s seawater intake seacock.
2. Before using the head, pump water into the bowl
to wet the sides.
3. After use, pump until the bowl is clean.
4. Pump a few more times to clean the lines.
5. If excess waste causes the water to rise in the
bowl, stop pumping until the water recedes.
• Close the intake seacock when the system will not
be used for long periods of time.
Winterizing the System
Read the marine head’s operation and maintenance
manual for winterizing instructions.
40
AFT
HOLDING
TANK VENT
HOLDING
TANK
TO HOLDING
TANK PUMPOUT DECK
FITTING
285 • Owner’s Manual Supplement
Chapter 6: Plumbing
Macerator (If Equipped)
To use the macerator to
pump waste directly overboard (where regulations
permit):
1. Open the overboard discharge seacock.
2. Press both macerator
switches at the same
time to run the pump.
3. Stop running the macerator as soon as the holding tank is empty.
4. Close the overboard discharge seacock when
you are done pumping.
HOLDING TANK
MACERATOR
DISCHARGE SEACOCK
(IF EQUIPPED)
41
285 • Owner’s Manual Supplement
Chapter 7: Deck Equipment
Cleats and Tow Eyes
!
WARNING!
PERSONAL INJURY and/or PRODUCT or PROPERTY DAMAGE HAZARD!
NEVER lift your boat using the bow and stern eyes or the cleats.
Read the section on towing in the Cruiser & Yacht Owner’s Manual before:
• Towing anything behind your boat.
• Being towed by another vessel.
Windlass (If Equipped)
!
DANGER!
DANGER
PERSONAL SAFETY HAZARD!
• ALWAYS secure the anchor and other loose objects BEFORE getting underway.
• The anchor and other items that are NOT properly secured can come loose when your boat
is moving and cause personal injury or death.
!
CAUTION
PRODUCT DAMAGE HAZARD!
Do NOT pull your boat to the anchor using the windlass or continue to run the windlass if it has
stalled or is overloaded.
•
•
•
•
•
•
42
Read and follow the manufacturer’s instruction manual before using the anchor windlass for the first time.
The windlass can be controlled from a switch at the helm or from the deck foot switches.
Make sure that the windlass circuit breaker is turned On before using the anchor windlass.
To raise the anchor, use engine power (not the windlass) to move your boat to, and directly above, the anchor.
Dislodge the anchor from the bottom by pulling it straight up with the windlass.
Make sure the anchor is secured before getting underway.
285 • Owner’s Manual Supplement
Chapter 7: Deck Equipment
Canvas
!
CAUTION
PRODUCT or PROPERTY DAMAGE HAZARD!
Take down and securely stow ALL canvas BEFORE transporting your boat by road.
NOTICE
Two people are needed for most of the tasks listed in this section.
NOTICE
BEFORE cleaning and/or stowing your canvas or vinyl, read the sections later in this chapter,
Canvas Care and Vinyl Care.
1. Slide the main bow’s
windshield hinges over
the aft pre-drilled
holes in the side-windshield frames and
insert the securing
pins.
2. Starting with the center snaps, snap the aft
edge of the bimini top
to the radar wing.
3. Slide the forward
braces’ windshield
hinges over the forward pre-drilled holes
in the side-windshield
frames and insert the
securing pins.
4. Slide the end eyes of
the aft braces into the
deck hinges on the
radar wing and insert
the securing pins.
• The jaw slides (J)
should not need to be
adjusted.
• If you decide to adjust
the jaw slide positions,
get the correct measurements from your selling
dealer.
NOTE: STARBOARD SIDE SHOWN,
PORT SIDE TYPICAL
RADAR WING
AFT BRACE
MAIN BOW
FORWARD
BRACE
MAIN BOW WINDSHIELD HINGE
OVER AFT PRE-DRILLED HOLE
FORWARD BRACE WINDSHIELD
HINGE OVER FORWARD
PRE-DRILLED HOLE
END EYE
WINDSHIELD
HINGE
SECURING PIN
SECURING PIN
DECK HINGE
43
Chapter 7: Deck Equipment
285 • Owner’s Manual Supplement
Vinyl Curtains (If Equipped)
Forward Bimini Curtain
NOTICE
When taking down the forward bimini curtain, avoid socket/stud problems by using the following method to unfasten the curtain sockets from the studs on the windshield frame:
• Grasp the edge of the curtain just below each socket and roll the edge upwards. The socket
should pop off easily.
1. At the top center of the curtain there are two zippers. Zip four to six inches of each zipper to the bimini top.
2. Starting at the bottom center of the curtain and working outwards, press the sockets over the studs on the windshield frame.
3. Fasten the top corner curtain studs to the bimini sockets.
4. Finish zipping the top zippers.
Side Bimini Curtains
1.
2.
3.
4.
5.
6.
7.
Starting on either side, zip four to six inches of the top zipper to the bimini top.
Zip three to four inches of the forward vertical zipper to the forward bimini curtain.
Start with the top aft snap and work your way down snapping the curtain to the radar arch.
Now work your way forward snapping the curtain to the side-windshield frame.
Finish zipping the forward vertical zipper.
Finish zipping the top zipper.
Repeat steps one through six on the other side.
Camper Curtains
1. Zip together four to six inches of all camper curtain zippers.
2. Snap all curtain snaps to the radar arch and deck.
3. Finish zipping all zippers.
44
285 • Owner’s Manual Supplement
Chapter 7: Deck Equipment
Canvas Care (see also ‘Clear Vinyl Care’ on next page)
• After each use, especially in saltwater, rinse the canvas with cold freshwater.
• Before stowing, let the canvas air-dry completely.
• The canvas can be rolled or folded for stowage.
Cleaning the Canvas
!
CAUTION
NEVER use detergents when washing the canvas. Detergents can destroy the water repellency,
and mildew/UV resistant finish of your canvas.
Regularly clean the canvas to prevent dirt, pollen, and etc. from embedding in the fabric. Generally, it is easiest to
wash the canvas while it is installed on your boat.
• Use a soft-bristled brush to remove all dust and loose dirt.
1. Hose down the canvas with freshwater.
2. Gently wash the canvas with a solution of lukewarm water (no more than 100° F) and non-detergent soap, such
as Lux or Ivory Flakes.
3. Rinse thoroughly to remove the soap.
4. Before stowing, let the canvas air-dry completely.
Stubborn Stains
!
CAUTION
• Soaking in bleach solutions may remove the waterproof finish of the fabric and may also
decrease the life of the polyester thread used in the canvas.
• If needed, a water repellent treatment should be reapplied to your canvas. Ask your dealer
about the treatments available for your boat’s canvas.
Some stubborn stains may resist normal washing and you can try the methods below. However, these methods may
remove the waterproof finish of the fabric and may also decrease the life of the polyester thread used in the canvas.
Reapply a water repellent treatment as needed.
Method 1
1. Add 1/8 cup (2 oz.) of non-chlorine bleach to one gallon of water and mix thoroughly.
2. Thoroughly wet the canvas and then gently scrub the stained area with the weak bleach solution.
3. Rinse with cold water to remove all of the solution.
Method 2
1. Add 1/2 cup (4 oz.) of non-chlorine bleach and 1/2 cup (4 oz.) Ivory Flakes to one gallon of water and
mix thoroughly.
2. Soak the canvas in this solution for about 20 minutes.
3. Rinse with cold water to remove all of the solution.
45
Chapter 7: Deck Equipment
285 • Owner’s Manual Supplement
Clear Vinyl Care
•
•
•
•
•
!
CAUTION
NEVER store the clear vinyl pieces wet, as this will cause a milky film to develop.
NEVER fold or crease the clear vinyl pieces as cracking will occur.
Clear vinyl is NOT intended for use when your boat is in storage or being moored.
Clear vinyl does NOT hold up well against ultraviolet rays.
Under direct sunlight conditions, do NOT let the clear vinyl touch the framework. The
framework radiates heat and can burn the clear vinyl.
• After each use, especially in saltwater, rinse the clear vinyl with cold freshwater.
• Before stowing, the clear vinyl must be completely dry. Air drying is best, but you can also carefully dry the vinyl
with a chamois or soft cotton cloth.
• The clear vinyl can be
rolled or laid out flat
NEVER FOLD OR CREASE CLEAR VINYL!
FOLDING OR OTHERWISE CREASING
for stowage.
CLEAR VINYL WILL CAUSE DAMAGE
SUCH AS CRACKING TO OCCUR
• Never fold or crease the
clear vinyl parts as
cracking will occur.
Cleaning the Clear
Vinyl
Regularly clean the clear
vinyl to prevent dirt, pollen, and etc. from marring
the surface. Generally, it is
easiest to clean the clear
vinyl while it is installed
on your boat.
1. Hose down the clear
vinyl with freshwater.
2. Using a soft cotton
cloth (paper towels
are abrasive and
should never be used
on clear vinyl), gently
wash the clear vinyl
with soap and water.
3. Rinse thoroughly to
remove the soap.
AFTER CLEAR VINYL PARTS HAVE
COMPLETELY AIR DRIED THEY CAN BE
ROLLED OR SIMPLY LAID FLAT FOR STOWAGE
4. Before stowing, the
clear vinyl must be
completely dry. Air
drying is best, but you can also carefully dry the vinyl with a chamois or soft cotton cloth.
• Ask your dealer about products available to keep the clear vinyl polished and looking new.
46
285 • Owner’s Manual Supplement
Chapter 8: Appliances & Entertainment Systems
NOTICE
Always keep an approved ABC-type fire extinguisher in galley area.
• The separate instruction sheets or manuals for all appliances and entertainment systems contain detailed instructions and important safeguards.
• Read these instruction sheets and manuals before using your boat’s appliances and entertainment systems.
• If applicable, make sure the 110-volt AC breaker is turned On for the appliance or entertainment system you wish
to use.
Refrigerator
The refrigerator runs on 12-volt DC power unless 110-volt AC power is being supplied by shore power and the
refrigerator’s circuit breaker on the 110-volt AC master panel is On.
Audio Equipment
NOTICE
AM radio reception may be impaired anytime the engine is running.
47
Chapter 8: Appliances & Entertainment Systems
285 • Owner’s Manual Supplement
Alcohol/Electric Stove
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
• The alcohol stove is a source of dangerous carbon monoxide gas (CO).
• BEFORE using the alcohol stove, Open doors and windows to make sure
there is enough fresh air for ventilation.
• Read the Carbon Monoxide (CO) section of Chapter 1 in this supplement.
WARNING!
!
• Open flame cooking appliances consume oxygen. This can cause asphyxiation or death.
• Maintain open ventilation.
!
WARNING!
BURN/SCALDING and/or FIRE HAZARD!
•
•
•
•
•
Read the stove’s instruction manual BEFORE using.
ALWAYS keep an approved ABC-type fire extinguisher in the galley area.
Do NOT use the stove while underway.
Any non-cooking devices on or near your stove during use are potential fire hazards!
Do NOT touch the burners, grates or nearby surfaces as they may be hot even when they are
dark in color.
• Areas near the burners and grates may become hot enough to cause burns.
• During and after use, do NOT touch or let clothing or other flammable material come in
contact with the heated units or the areas near the units (burner tops, main frame sides and
back, sea rails and pot holders) until they have had sufficient time to cool.
!
CAUTION
PRODUCT DAMAGE HAZARD!
To prevent overheating which can destroy the electric burner elements, NEVER try to use both
alcohol and electric burners at the same time.
48
285 • Owner’s Manual Supplement
Chapter 9: Convertible Seats, Beds, & Tables
Dinette
1. Remove the seat back cushions (A) and seat bottom cushions (B).
2. Push in the spring loaded locking pin (C) and fold the table leg (D)
under the dinette table top (E).
A
E
C
D
B
3. Pull the dinette table top (E) straight out and lower it.
E
4. Replace the seat bottom cushions (B) and place the filler cushion (F)
on the table top.
5. Replace the seat back cushions (A).
A
F
B
49
285 • Owner’s Manual Supplement
Chapter 10: Lights
Care and Maintenance
All of the lights installed on your boat are of top quality, but you should be aware that failure may periodically occur
for a variety of reasons:
1.
2.
3.
4.
There may be a blown fuse - replace the fuse.
The bulb may be burned out - carry spare bulbs for replacement.
A wire may be damaged or may have come loose - repair as required.
The bulb base may be corroded - clean the base and coat it with non-conductive electrical lubricant.
Interior & Exterior Lights
!
CAUTION
• Be conservative in the use of battery power.
• Prolonged use of cabin interior lights (overnight) WILL result in a drained battery.
• The lights are powered by your boat’s 12-volt DC system.
• The battery switch must be turned On for the lights to work.
Navigation Lights
!
CAUTION
Avoid the storage of gear where it would block navigation lights from view.
NOTICE
Running lights are legally required to show boat direction and right-of-way at night.
Read the navigation light section of the Cruiser & Yacht Owner’s Manual.
Spotlight (If Equipped)
Read the spotlight operating instructions before using the spotlight.
50
285 • Owner’s Manual Supplement
Chapter 11: Air Conditioning System (If Equipped)
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
• Dangerous carbon monoxide gas (CO) can be brought into your boat
through the air conditioning system.
• Read the Carbon Monoxide (CO) section of Chapter 1 in this supplement.
!
CAUTION
SYSTEM DAMAGE HAZARD!
The air conditioning system’s seawater intake seacock MUST be Opened BEFORE turning On
the air conditioner and MUST stay Open during use.
SEAWATER
INTAKE
SEACOCK
SEAWATER
STRAINER
INTAKE
PUMP
AIR CONDITIONER
SUMP PUMP
AIR CONDITIONER
AIR CONDITIONER
THRU-HULL DRAINS
FORWARD
• Read the air conditioner manual before using the air conditioning system.
• Before using the air conditioning system, make sure the breakers on the 110-volt AC master panel are turned On
and that the system’s seawater intake seacock is Open.
• The seacock must remain Open while the air conditioner is in use.
• Check the seawater strainer for debris before each use of the air conditioning system.
• If the strainer needs to be cleaned out, follow the directions in the Seawater Systems section of Chapter 6 in
this supplement.
51
285 • Owner’s Manual Supplement
Chapter 12: Electrical System
!
DANGER!
EXTREME FIRE, SHOCK and EXPLOSION HAZARD!
• To minimize the risks of fire and explosion, NEVER install knife switches or other arcing
devices in the fuel compartment.
• NEVER substitute automotive parts for marine parts. Marine electrical, ignition and fuel
system parts were designed and manufactured to comply with rules and regulations that
minimize risks of fire and explosion.
• Do NOT modify the electrical systems or relevant drawings.
• Have qualified personnel install batteries and/or perform electrical system maintenance.
• Make sure that ALL battery switches are turned Off BEFORE performing any work in the
engine spaces.
WARNING!
!
FIRE and EXPLOSION HAZARD!
Fuel vapors can explode! BEFORE electrical system maintenance or activation of electrical devices:
1. Check the bilge areas for fuel vapors or leaking fuel. If you see leaking fuel or smell
fuel vapors:
a. Do NOT start the engine, do NOT turn On any electrical devices, extinguish ALL ciga-
rettes, cigars, and other sources of flame or ignition.
b. Get everyone off your boat.
c. Get trained help to find and fix the problem.
2. Run the bilge blower(s) for at least four minutes prior to engine starting, electrical system
maintenance, or activation of electrical devices.
!
CAUTION
SHOCK and ELECTRICAL SYSTEM DAMAGE HAZARD!
When the engine is running, NEVER turn Off the battery switch or disconnect the battery cables. Doing either could cause damage to your boat’s engine and/or
electrical system.
NOTICE
Electrical connections are prone to corrosion. To reduce corrosion-caused electrical problems:
• Keep ALL electrical connections clean.
• Apply a spray-on protectant that is designed to protect connections from corrosion.
52
285 • Owner’s Manual Supplement
Chapter 12: Electrical System
12-Volt DC System
Batteries
• The batteries supply electricity for lights, 12-volt accessories, and engine starting.
• The Electrical section of Chapter 8 in the Cruiser & Yacht Owner’s Manual provides battery care and
maintenance instructions.
Battery Switch
!
CAUTION
SHOCK and ELECTRICAL SYSTEM DAMAGE HAZARD!
When the engine is running, NEVER turn Off the battery switch or disconnect the battery cables. Doing either could cause damage to your boat’s engine and/or electrical
system.
NOTICE
Make sure your selling dealer fully explains how to use the battery switch.
• Standby-loads, such as the
automatic bilge pumps and
the stereo memory, are not
affected by the battery switch
since they are wired directly
to the battery (see the Wiring
Diagrams section of this
chapter for more details).
• Turn the battery switch to the
Off position whenever your
boat will be unoccupied for
long periods of time.
12-VOLT DC STANDBY LOADS PUSH-TORESET CIRCUIT BREAKERS
BATTERY
SWITCH
Fuses & Circuit Breakers
• Circuit breakers for the engine and main accessory power are on the 12-volt DC push-to-reset circuit breaker
panel and the battery switch panel.
• Some equipment may have secondary fuse protection at the unit, behind the battery switch panel, or at
the batteries.
• For the locations of the battery switch panel and the 12-volt DC push-to-reset circuit breakers, see the Component
Locations section of Chapter 2 in this supplement.
53
Chapter 12: Electrical System
285 • Owner’s Manual Supplement
12-Volt DC Accessory Outlet
!
CAUTION
Do NOT use the 12-volt DC accessory outlet with a cigarette or cigar lighter. High temperatures may melt the outlet.
• The outlet can be used with any 12-volt device which draws 15-amps or less.
• Each outlet is protected by a 15-amp breaker on the 12-volt DC push-to-reset circuit breaker panel.
Alternator
The alternator will keep the battery properly charged when the engine is running at, or above, cruising speeds.
Battery Charger
!
CAUTION
ENGINE and ELECTRICAL SYSTEM DAMAGE HAZARD!
NEVER run your boat’s engines and the battery charger at the same time.
!
CAUTION
• The battery charging systems (alternator and battery charger) installed on your boat are
designed to charge conventional lead-acid batteries.
• BEFORE installing gel-cell or other new technology batteries, consult with the battery manufacturer about charging system requirements.
• Before using the battery charger, read all instructions and warnings: (1) on the battery charger, (2) on the batteries,
and (3) in the battery charger manual.
• The battery charger will automatically charge your boat’s batteries when 110-volt AC power is being provided by
shore power, and the battery charger circuit breaker on the 110-volt AC master panel is On.
• The battery switch can be in any position during charging.
• During battery charging you may use 12-volt accessories, such as the lights and stereo, but battery charging will
take longer.
54
285 • Owner’s Manual Supplement
Chapter 12: Electrical System
110-Volt AC System
!
CAUTION
WATER HEATER DAMAGE HAZARD!
• Do NOT turn On the water heater circuit breaker on the 110-volt AC master panel until the
water heater tank is COMPLETELY filled with water.
• The tank is full if water flows from the tap when the hot water is turned On in the galley.
• Even brief water heater operation with a dry tank WILL damage the heating elements.
• Warranty replacements will NOT be made on elements damaged in this manner.
NOTICE
• When using shore power, the use of several 110-volt AC accessories at the same time can
result in an overloaded circuit.
• You may have to turn Off one or more accessories to use another accessory.
• To gain a basic understanding of your boat’s
110-volt AC system, read the handbook A
Boater’s Guide To AC Electrical Systems. If
this handbook is not in your owner’s packet,
call 360-435-8957 and the handbook will be
mailed to you.
• The 110-volt AC system is energized by
shore power.
• Individual breakers on the 110-volt AC
master panel must be turned On to supply
power to the accessories you wish to use.
• The 110-volt AC master panel may contain
circuit breakers for accessories that are not
available for your boat.
110-VOLT AC MASTER PANEL (SINGLE SHORE POWER)
BATTERY
CHARGER
AC VOLTS
RECEPTACLES
WATER HEATER
RANGE
REFRIGERATOR
AC MAIN
AIR/HEAT
REVERSE
POLARITY
MICROWAVE
ACCESSORY
110-VOLT AC MASTER PANEL (DUAL SHORE POWER)
55
Chapter 12: Electrical System
285 • Owner’s Manual Supplement
Shore Power
!
DANGER!
FIRE, EXPLOSION and SHOCK HAZARD!
• Do NOT alter the shore power connectors and use ONLY compatible connectors.
• Turn Off ALL breakers and switches on the 110-volt AC master panel BEFORE plugging in
or unplugging the shore power cord.
• To prevent shock or injury from dropping a "hot" cord into the water:
a. ALWAYS plug the shore power cord into the boat inlet first, and then into the
dockside outlet.
b. When unplugging from shore power, ALWAYS unplug the shore power cord from the
dockside outlet first.
• NEVER leave the shore power cord plugged into the dockside outlet ONLY.
• ONLY use shore power cords approved for marine use. NEVER use ordinary indoor or outdoor extension cords.
WARNING!
!
SHOCK and ELECTRICAL SYSTEM DAMAGE HAZARD!
• Monitor the polarity indicator lights EVERY TIME you connect to shore power.
• If a reversed polarity light turns On when you are connecting to shore power, do NOT turn
On the main breaker switches.
• Instead, IMMEDIATELY unplug the shore power cord (ALWAYS from the dockside outlet
first) and alert marina management.
!
WARNING!
SHOCK and ELECTRICAL SYSTEM DAMAGE HAZARD!
• BEFORE each use, check the shore power cord for defects or damage.
• NEVER use a damaged or faulty cord since the danger of fire and electrical shock exists.
• Do NOT pinch the shore power cord in doors or hatches, or coil the shore power cord too
tightly, since these situations can generate enough heat to result in a fire.
• If a shore power cord is dropped into the water, COMPLETELY dry the blades and contact
slots BEFORE using.
!
CAUTION
ELECTRICAL SYSTEM DAMAGE HAZARD!
• NEVER connect to dockside power outside of North America unless you have the international electrical conversion option.
• Using several 110-volt AC accessories at the same time can result in an overloaded circuit.
You may have to turn Off one or more accessories to use another accessory.
• Use double insulated or three-wire protected electrical appliances whenever possible.
56
285 • Owner’s Manual Supplement
Chapter 12: Electrical System
• Single shore power 110-volt/60-hertz AC systems features one 110-volt/30-amp shore power receptacle.
• If your boat has an air conditioning system, a second (dual) 110-volt/30-amp inlet has been installed.
• Dual shore power inlets are labeled LINE 1 and LINE 2, which corresponds to the SHORE POWER 1 and
SHORE POWER 2 master breakers on the 110-volt AC master panel.
• LINE 1 and LINE 2 are independent of each other except when the parallel switch is used.
Connecting to Shore Power
!
WARNING!
SHOCK and ELECTRICAL SYSTEM DAMAGE HAZARD!
• Monitor the polarity indicator lights EVERY TIME you connect to shore power.
• If a reversed polarity light turns On when you are connecting to shore power, do NOT turn
On the main breaker switches.
• Instead, IMMEDIATELY unplug the shore power cord (ALWAYS from the dockside outlet
first) and alert marina management.
1. Review all hazard information at the beginning
of this section, Shore Power.
2. Turn Off the shore power master circuit
breaker(s) and all switches and breakers on the
110-volt AC master panel.
3. Attach the shore power cord(s) to the boat
inlet(s) first, then to the dockside outlet(s).
4. Turn On the SHORE POWER 1 and SHORE
POWER 2 (if equipped) master breaker(s) on
the 110-volt AC master panel.
5. As needed, turn On the individual component
breakers on the 110-volt AC master panel.
SHORE POWER INLET(S)
(IF EQUIPPED)
TYPICAL SHORE
POWER INLET
Parallel Switch (Only if Equipped with Dual Shore Power)
NOTICE
• When using the parallel switch do NOT exceed 30 total amps.
• The amperage of each component breaker is shown on the breaker itself.
• The voltage on each line can be read on the voltmeter on the 110-volt AC master panel.
When only one dockside outlet is available, you can use the parallel switch to provide power to both lines.
1. Connect to shore power as described in the Connecting to Shore Power section above.
2. Switch the parallel switch (transfers power from line 1 to line 2) On instead of the SHORE POWER 2
master breaker.
3. Turn On the individual component breakers as required.
57
Chapter 12: Electrical System
285 • Owner’s Manual Supplement
Electrical Routings
Hull Harnesses
ENGINE
HARNESS
BONDING
BUSS BAR
TRIM TAB PUMP
GROUND
BUSS BAR
TRIM & TILT PUMP
BLOWER
AFT BILGE PUMP
AIR CONDITIONER WATER
PUMP (IF EQUIPPED)
MACERATOR
(IF EQUIPPED)
BATTERY CHARGER
FIXED FIRE
BOTTLE
(IF EQUIPPED)
FUEL TANK SENDER
INVERTER
SWITCH PANEL
FORWARD BILGE PUMP
HELM
SHOWER DRAIN
SUMP BOX
REFRIGERATOR
STARBOARD
PORT
AIR CONDITIONER
(IF EQUIPPED)
AIR CONDITIONER SUMP
PUMP (IF EQUIPPED)
58
285 • Owner’s Manual Supplement
Chapter 12: Electrical System
Deck Harnesses
NOTE: VIEWS ARE UNDERSIDE OF DECK
FORWARD DECK
TO AFT
DECK
STEP
LIGHT
STARBOARD
LIGHT
SWITCH
DASH
COMPASS
OVERHEAD
LIGHT
WIPER
TO GALLEY
LIGHTS
OVERHEAD
LIGHTS
PORT
NAVIGATION
LIGHTS
AFT DECK
RADAR WING PLUG
STARBOARD
COURTESY LIGHT
SIDE PANEL &
SHIFTER PLUG
AFT
PORT
COURTESY LIGHT
OVERHEAD
LIGHTS
CO MONITOR
59
Chapter 12: Electrical System
110-Volt AC Electrical System Single Dockside
60
285 • Owner’s Manual Supplement
285 • Owner’s Manual Supplement
Chapter 12: Electrical System
110-Volt AC Electrical System Dual Dockside
61
Chapter 12: Electrical System
Engine Electrical System
62
285 • Owner’s Manual Supplement
285 • Owner’s Manual Supplement
Important Records
Selling Dealer
Electronics
Name Of Dealership
Manufacturer
Address
Model Name/Number
Serial Number
Phone/FAX/E-mail
Manufacturer
Model Name/Number
Sales Manager
Serial Number
Service Manager
Manufacturer
Model Name/Number
Engine
Serial Number
Manufacturer
Model Name/Number
Manufacturer
Model Name/Number
Engine Serial Number
Serial Number
Propeller
Manufacturer
Manufacturer
Model Name/Number
Pitch
Serial Number
Model Number
Fuel System
Fuel Capacity
Filter Type
Key Numbers
Ignition
Other
63
285 • Owner’s Manual Supplement
Float Plan
Before going boating, fill out a copy of this float plan (or similar) and leave it with a reliable person whom you can
depend on to contact the Coast Guard or other rescue organization, if you do not return as scheduled.
Description of Boat
Persons Onboard
Registration/Documentation Number
Length
Make
Hull Color
Full Name
Type
Age
Health
Phone Number
Trim Color
Full Name
Fuel Capacity
Engine Type
Number of Engines
Age
Health
Phone Number
Distinguishing Features
Full Name
Distinguishing Features
Age
Health
Phone Number
Operator of Boat
Full Name
Full Name
Age
Male or Female
Age
Health
Phone Number
Health
Full Name
Address
Age
Health
Phone Number
Address
Full Name
Phone/FAX/E-mail
Operator’s Experience
Age
Health
Phone Number
Full Name
Age
Health
Phone Number
Full Name
Age
64
Health
Phone Number
285 • Owner’s Manual Supplement
Float Plan
Survival Equipment
Trip Expectations
Marine Radio (Yes/No)
Type
Frequencies
Number of PFDs
Flares (Yes/No)
Mirror (Yes/No)
Smoke Signals (Yes/No)
Flashlight (Yes/No)
Food (Yes/No)
Departing From
Departure Date
Departure Time
Stopover 1
Water (Yes/No)
Anchor (Yes/No)
Raft/Dinghy (Yes/No)
Arrive No Later Than: Date
Paddles (Yes/No)
EPIRB (Yes/No)
Other
Other
Other
Other
Arrive No Later Than: Time
Stopover 2
Arrive No Later Than: Date
Arrive No Later Than: Time
Vehicle Description
Stopover 3
Make
Model
Arrive No Later Than: Date
Color
Arrive No Later Than: Time
License Number
Stopover 4
Where is the Vehicle Parked?
Arrive No Later Than: Date
Arrive No Later Than: Time
Stopover 5
Arrive No Later Than: Date
Arrive No Later Than: Time
Stopover 6
Arrive No Later Than: Date
Arrive No Later Than: Time
Final Destination Port (If Different Than Home Port)
Arrive No Later Than: Date
Arrive No Later Than: Time
If not returned by the date and time listed above, call
the Coast Guard or other local authority.
Coast Guard Phone Number
Local Authority Phone Number
65
Owner’s Notes
Owner’s Notes
Owner’s Notes
Bayliner • P.O. Box 9029 • Everett, WA 98206 • 360-435-5571
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement