Duratrax Onyx 255 Product Manual

Duratrax Onyx 255 Product Manual
™
Quick Reference Guide to Programming
NOTE: This guide does not replace the entire instruction manual as supplied with this charger. Read
AC/DC DUAL CHARGER WITH BALANCING
the provided manual in its entirety before use, paying particular attention to all safety warnings!!
1. Output 1 and Output 2 are independent. Connect the battery to one output and use the appropriate screen and controls for that output.
2. START: Connect the charger to power. The CHARGE START screen will appear, with the active battery memory number shown in the
top right corner (>0<). All settings for this memory will automatically scroll across the bottom of this screen or can be scrolled through using
the ▼ and ▲ buttons. If these settings are acceptable for the battery to be charged, press and hold START and charge will begin.
3. SELECT A MEMORY: All ten memory profiles are pre-programmed with charge settings as
shown in the chart. Press CHANGE then ▼ or ▲ to find the correct profile. Press CHANGE again
to confirm. Press and hold START and charging will begin.
4. MANUAL SETUP: Follow the steps below
to find the BATTERY SETUP screen to adjust
the charger settings to match a specific battery.
PRESS
MEMORY NO.
0
1
2
3
4
Battery Type
Cell Count
Capacity (mAh)
Current
Safety Time (minutes)
Delta Peak (mV/C)
Trickle Current (mA)
LiPo
2
4000
4.0A
120
–
–
LiPo
2
5000
5.0A
120
–
–
LiPo
2
5700
5.7A
120
–
–
LiPo
3
5000
5.0A
120
–
–
LiPo
3
6400
6.4A
120
–
–
PRESS
BATTERY TYPE: Press CHANGE,
then ▼ ▲ to find the proper battery type.
Press CHANGE to confirm.
PRESS
CELL[02]: Press CHANGE, then ▼▲ to
find the proper number of cells in the
battery (confirmed by the voltage shown
at the bottom of the screen). Press
CHANGE to confirm.
PRESS
CAPACITY: Press CHANGE, then ▼▲
to find the rated capacity value of the
battery. Press CHANGE to confirm.
PRESS
CURRENT: Press CHANGE, then ▼▲
to find the desired current. Press
CHANGE to confirm.
PRESS
S_TIMER: Press CHANGE, then ▼▲ to
find the desired backup safety timeout for
charge. Press CHANGE to confirm.
5. START CHARGE: After all settings are made, press
until the
CHARGE START screen shows. Press and hold START for 2 seconds
and fast charge will begin.
5
6
7
8
PRESS
PRESS
PRESS
MELODY: Press CHANGE, then ▼▲ to
change the melody type. Press CHANGE
to confirm.
PRESS
BEEP OFF: Press CHANGE, then ▼▲
to turn ON or OFF. Press CHANGE to
confirm.
9
NiCd NiMH NiMH NiMH NiMH
6
6
6
7
7
1800 3000 5000 3000 5000
1.8A 3.0A 5.0A 3.0A 5.0A
90
90
90
90
90
10
8
8
8
8
200 250 250 250 250
TO
CHARGE
START
SCREEN
PRESS
INPUT VOLTAGE: Shows the voltage
at the charger’s input.
PRESS
OUTPUT VOLTAGE: Shows
voltage at the charger’s output.
the
PRESS
PEAK VOLTAGE: Shows the maximum
voltage measured on the battery during
charge.
PRESS
CHG CAPACITY: Shows how much
energy was delivered to the battery during
charge.
PRESS
CHG TIME: Shows how many minutes
elapsed during the charge process.
WARNING!! NEVER LEAVE A BATTERY UNATTENDED WHILE BEING CHARGED! REFER
TO THE PROVIDED INSTRUCTION MANUAL FOR FULL DETAILS.
DTXP4255 QRG
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement