SportsArt 1200N Owner Manual

SportsArt 1200N Owner Manual
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
OPERATING INSTRUCTIONS
CAUTION: DO NOT STAND ON THE BELT WHEN STARTING.
Safety key
The safety key is required to operate the treadmill. The safety key should be used as
an emergency stop by clipping the cord to your exercise clothing. Be sure to remove
the safety key from your exercise clothing after you have finished your workout, and
place it to the key
"NOT IN USE"
position for your convenience or store in a safe place
to avoid use by children or persons unfamiliar with this treadmill.
Turn on the power switch located on the front of the treadmill. Place the safety key
into the "SAFETY KEY" position on the electronics package in order for the unit to
function.
UNDERSTANDING THE ELECTRONICS PACKAGE
Key functions:
SAFETY KEY: Turn on the POWER switch located on the front of the machine. Put
the safety key on the "SAFETY KEY" position of the electronics package to operate
the treadmill.
(NOT IN USE)
: After your workout, place the safety key on
(NOT IN USE)
position for your
convenience. Then turn the power switch off.
SPEED ▼▲ : Use the speed ▼▲ keys to adjust your desired speed. The speed
range for the treadmill is from 0.5-10 MPH (0.8-16 KPH).
Press the speed ▲ key to increase the speed and press the speed ▼
key to decrease the speed.
INCLINE ▼▲ : Use the INCLINE▼▲ keys to raise or lower the treadmill. The
incline range for the treadmill is from 0%-12%.
▼▲ MODE: When you place the safety key in its place, the electronics package will
automatically access into MODE function. Press the mode key, and this
will scroll you through the different modes. With each press of the
MODE key, the display will alternately show TIME, DIST(Distance),
CAL(Calories), SCAN or PULSE.
▼▲ keys: These keys are used to choose the desired TIME or DISTANCE.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
STOP/RESET: When you press the Stop/Reset button, and the treadmill will slowly
come to stop.
Press the Stop/Reset button once again, all display windows
information will be cleared.
PROGRAM: The 1200N features a total of three (3) professionally designed workout
programs. The programs control the elevation, while you control the
speed of your workout. During the actual programs, you cannot change
the elevation percentage, but you can change the speed of the
treadmill.
Press the PROGRAM key to scroll through the 3 programs. The P1-P3 will be
displayed in the central LED window, when you have chosen the Program you want,
press the MODE ▼▲ key to select the TIME or DIST. Use the TIME or DIST ▼▲
keys to select your desired TIME or DIST (but not both), then press the SPEED keys
to begin.
During these programs, you control the speed, and the unit will automatically switch
between the elevation percentages, giving you the feeling of running on hills and
level ground.
The course profile for each PROGRAM is as follows:
1
2
5
0
1
9
10
3
5
5
7
1
1
3
5
7
9
7
2
3
5
0
0
3
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
What each of the categories means:
TIME: The range available in TIME mode is 00:00-99:59 minutes. Use the MODE ▼
▲ key to select the time mode. When TIME LED is lit in the display, use the
▼▲ keys to adjust the desired time.
The electronics package will BEEP for 10 seconds when your desired time is
reached, then will start to count up if you workout continues. Each press of
the key change the time by 1 minute.
DIST: The distance of the treadmill will register goes from 0-99.99 miles or 0-999.9
kilometers. Use the MODE ▼▲ key to select the DIST mode.
When DIST LED is lit in the display, use the ▼▲ keys to adjust the desired
distance. Each press of the key changes the distance by 0.1 mile or 0.1 km.
The electronics package will BEEP for 10 seconds when your desired
distance is reached, then will start to count up if you workout continues.
CAL: This readout gives you the amount of calories burned, the range of calories is
from 0-999.9CAL.
SCAN: The SCAN will result in the display alternation between Modes readouts
every 4 seconds.
PULSE: If your electronics package is equipped a pulse feature. Use a pulse meter
to monitor your heart rate either measure by fingertip or earlap. This readout
measures your heart rate per minute.
Operation: 1. Plug the pulse connector into the pulse socket.
2. Press MODE ▼▲ key to the pulse mode, the pulse indicator lit
located on the electronics package.
3. Rub your earlap or fingertip 15 times before clipping the sensor to it in
order to get the best results.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
RUNNING ON THE TREADMILL:
Now, you have become familiar with your treadmill's operation and are ready to
exercise:
1. Plug the treadmill into a standard outlet. Turn on the power switch located on the
front of the machine.
2. Straddle the belt with your feet on the right and left staging platforms. Place the
safety key on the "SAFETY KEY" position of the electronics package to operate
the treadmill.
3. Balancing one hand on the handrail. Adjust the SPEED ▲ key until you reach
1.5-2.0 MPH / 2.5-3.5 KPH, a comfortable walking speed. With both hands on the
handrails, place one foot, then the other on the treadmill, and walk for a few
minutes to get comfortable with your machine.
4. After you are walking in an easy, relaxed, and steady fashion, release your grip on
the handrails, and let your arms swing freely and naturally.
5. When you feel comfortable walking, you may wish to jog. Hold the handrail with
one hand, use the other hand to increase the speed.
6. Remember to hold the handrail when using the electronics package, or adjust the
speed. Holding the handrail with one hand will help to maintain your balance,
especially when slowing down or stopping. Also, remember to hold onto the
handrail when dismounting.
7. It is best to do a cooldown before you bring the machine completely stop.
GUIDELINES FOR EXERCISE
How long should I exercise?
The duration of your exercise session depends on your fitness level. In general, it is
recommended that you maintain your heart rate in the training zone for at least 10
minutes to realize an aerobic benefit. As your fitness level increases, you will be able
to maintain your heart rate in the training zone for longer periods: usually between
20 and 30 minutes.
When first starting your workout, use the first several minutes to warm up, then
slowly increase your workload to bring your heart rate into your specific training
zone. At the end of your workout, gradually decrease your workload, then exercise
lightly as a "cool down".
How often should I exercise?
Aerobic exercises, to achieve the greatest benefits, should be performed 3-5 times a
week. It is important to allow sufficient time, at least 24 hours, for your body to
recover after exercise.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
MAINTAINING YOUR TREADMILL
Your treadmill relies on low friction for peak performance. The treadmill's low friction
operation depends on keeping the unit as clean as possible. See "Cleaning the
Treadmill" for more information.
Proper belt alignment is also important for proper operation of the treadmill. See
"Adjusting the Running Belt" for more information.
Cleaning the treadmill
CAUTION: Turn off unit and disconnect AC cord before cleaning.
Regular cleaning is recommended to keep your treadmill running at peak
performance.
Before your workout, use a dry cloth to clean the staging platform, exposed slider
deck, and under the belt as far as you easily reach. This removes any dirt or dust
which might enter the slider area and compromise the unit's running efficiency.
To clean the plastic parts, use a mild detergent and make sure the unit is
completely dry before operating. On the running surface, use a soft nylon scrub
brush. Do not use water to clean the belt or running surface, or to clean the
electronics package. Should water, for some reason, get on the electronics
package, immediately blow dry the electronics package.
It is recommended that you keep all liquids away from the unit during operation.
Spillage of liquids onto or into the machine will void the warranty.
Adjusting the running belt
Your treadmill comes with a belt alignment gauge located on the left side of the
motor cover (see Fig. 10). The edge of the running belt should be in the middle of
the green portion of the gauge. If the belt edge is in the green area, the belt does not
need adjusting. If the right edge is in the red portion, the belt needs adjusting
immediately.
ITEM:1200N
Fig.10
ITEM:1200NL
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
The belt is properly aligned at the factory. However, during shipping and handling or
by use on an uneven surface, the belt may move off center. Therefore, it is important
that you check the belt's alignment before using the treadmill.
The correct alignment of the running belt is critical for the smooth operation of the
treadmill.
CAUTION: DO NOT ALLOW ANYONE TO WALK ON RUNNING BELT DURING
THIS PROCEDURE.
Failure to realign the belt could result in tearing or fraying of the belt, which is not
covered in the warranty. Please follow the adjustment procedure listed below :
1. Turn on the power switch located on the front of machine. Place the SAFETY KEY
on the "SAFETY KEY" position.
2. Press the SPEED ▲ key to increase the speed until the speed registers 2.0mph /
3.2kph on the digital display.
3. While the unit is running at 2 mph/3.2kph, determine where the belt is in relation to
the belt alignment gauge.
4. Should your belt be in the wrong color range, follow the steps below to return the
belt to the "safety zone":
5. If the belt is in the left red zone: Turn the left belt adjustment bolt located at the
rear of the treadmill clockwise 1/4 turn at a time, using the hex Allen wrench. Then
turn the right belt adjustment bolt counterclockwise 1/4 turn. Let the treadmill run
30 seconds, then check the position of the belt in the color gauge. If the belt still
has not returned to the green safety zone, repeat with another 1/4 turn until the
belt has returned to the middle of the green area. Do not turn adjusting bolt more
than 1/4 turn at a time.
If the belt is on the edge of the green color, please adjust it so it is in the middle of
the green color. You may turn the adjustment nut less than 1/4 turn at a time.
6. Conversely, if the belt is in the right red zone, turn the right belt adjustment nut
clockwise 1/4 turn, then turn the left adjustment bolt counterclockwise 1/4 turn.
Then let the treadmill run at least 30 seconds, check the position of the belt in the
color gauge. If it still has not returned to the green safety zone, repeat with
another 1/4 turn until the belt has return to the middle of the green area. Do not
turn adjusting bolt more than 1/4 turn at a time.
7. When the belt is back in the green "safety zone", you can continue your regular
use of the treadmill. Slowly increase the speed of the unit to 5.5 MPH (9 KPH),
and let it run for at least 45 seconds.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
Periodically monitor the position of the belt to ensure peak performance:
When you are using the treadmill, if you feel a pause in the belt with each foot plant
the belt is too loose. Stop the machine, check the belt tension, grab the running belt
off the deck in the middle (see Fig. 11 ~ Fig.11-3). There should be about 30 m/m
(1 1/8") or 3 kgs of "give" in the belt. If there is too much, then adjust both rear roller
bolts clockwise 1/2 turn at a time.
Fig.11-2
Fig.11
Fig.11-1
Fig.11-3
Then, try the belt tension again, if more adjusting is required, give both adjusting
bolts another slight turn. Do not adjust over 2 fullturns.
Conversely, if the "give" in the belt is too tight, adjust both rear roller bolts
counterclockwise 1/2 turn at a time (see Fig. 11-3).
CAUTION: To avoid injury, special care must be taken when adjusting the running
belt. Turn off the treadmill while adjusting or working near the rear rollers.
Remove any loose clothing or shoe laces and tie back your hair. Be very
careful to keep your fingers or any other objects clear of the belt and
rollers.
The treadmill is designed to carry specific weights at specific speeds. The treadmill
will not stop immediately if any object becomes caught in the belt or rollers.
Over tightening of the belt causes damage and premature failure of the precision
bearings in the front and rear rollers.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
TROUBLE SHOOTING:
CAUTION: SHUT OFF UNIT AND DISCONNECT AC CORD BEFORE MAKING
ANY REPAIRS OR MODIFICATIONS.
"ERR" messages
Note: If the electronics display shows "ERR 1, ERR 3, ERR 6 or ERR 7", please turn
off the POWER switch on the front of the machine. Allow the unit rest for 5 seconds,
then turn on the power switch begin operation again. Should the electronics package
display "ERR" again, please refer to the following section for more information. OR,
please contact your dealer for further instructions.
ERR 1- The optical switch mounted on the motor is not receiving the signal
reflected from the tachometer wheel. Please contact your dealer.
ERR 3- The user is running faster than the belt. Please turn the POWER switch off,
allow the machine to rest for 5 seconds, then try normal use again.
ERR 6- The unit's incline system is not responding, please replace the 0.5A (200240V) or 1A (100-120V) fuse located underneath the treadmill, make sure
your area standard voltage prior to replacement.
The incline system fuse holder is located under the frame at the front of the
machine (see Fig. 12).
100V-120V=1A
FUSE ( 200V-240V=0.5A)
100V-120V=12A
FUSE ( 200V-240V=7A
)
Fig.12
To remove the fuse, push on the fuse holder and then turn the holder
counterclockwise and the fuse holder with fuse will protrude.
Remove the damaged fuse and insert a new fuse, push the fuse and holder in, turn
clockwise to secure it.
If the unit still refuse to respond, please contact your dealer for more information.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
ERR 7- Once you turn on the machine, the computer display shows the ERR 7. The
computer receiving the signal reflected from VR incorrectly, that means the
wires disconnected. Please contact your dealer for further information.
Blank display
1. If you turn on the POWER switch and there is no light:
a. Check if the power cord is plugged securely into the wall socket.
b. Check that the power switch on the front of the unit is on the "ON" position. The
power switch should be lit.
c. If the power switch is no light, replace the fuse. Please refer to the
ELECTRONICS PACKAGE AND MOTOR FUSE FAILURE section for more
information.
d. If there is still no display after completing the above steps, please contact your
dealer for more information.
2. The power switch is lit, but no words appear on the display:
If the display slows no words, then the fuse on the driver board need to be
replaced, please check with your dealer for further information.
Electronics package and motor fuse failure
If you turn on the POWER switch and there is no light, and nothing displays on the
electronics package, then the fuse must be replaced.
CAUTION: MAKE SURE THE TREADMILL PLUG ALREADY REMOVE FROM
OUTLET BEFORE REPLACE THE FUSE.
The fuse holder 12 amp (100V-120V) / 7 amp (200V-240V) for electronics package
and motor are located under the frame at the front of the machine. Please make sure
your area standard voltage prior to replacement and follow the steps as shown in Fig.
12-1 to 12-3.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
REMOVE THE DAMAGED
FUSE AND INSERT A
NEW FUSE.
2
Fig.12-1
TURN
1
2
TURN
1
Fig.12-3
Fig.12-2
To remove the fuse for the electronics package and motor, push on the fuse holder
and then turn the holder counterclockwise and the fuse holder with fuse will protrude.
Remove the damaged fuse and insert a new fuse, pushing the fuse and holder in,
then turning clockwise to secure the fuse holder.
If the unit's electronics package refuses to respond after changing the fuse, please
contact your dealer for more information.
Fuse Failure For Incline System
Should the incline system refuses to respond, but there is power to the electronics
package and it remains operable, please replace the incline system fuse.
The 1 amp (100V-120V) / 0.5 amp (200V-240V) fuse is for the Incline system. To
remove the incline system fuse, push on the fuse holder and then turn the holder
counterclockwise and the fuse holder with fuse will protrude. Remove the damaged
fuse and insert a new fuse, pushing the fuse and holder in, then turning clockwise to
secure the fuse holder (see Fig. 12-1〜12-3).
If the incline system refuses to respond after changing the fuse, please contact your
dealer for more information.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
Fuse Failure For Drive Board
NOTE: If you are not a technician or do not have expert knowledge of this machine.
Please do not attempt to replace it.
If there is nothing displays on the electronics package, and the POWER SWITCH
located on the front of the treadmill is lit, then the fuse is damaged on the drive board
and must be replaced.
The fuse holder 0.5 amp for the drive board is located on the frame at the front of the
treadmill (see Fig. 13).
ITEM:1200N
Fig.13
ITEM:1200NL
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
Wiring Schematic:
220V(110V NONE)
1200N,1250N
BLACK
INDUCTOR
DC MOTOR
220V-BLUE
110V-WHITE
WHITE
SWITH
AC POWER
BLACK
7AF FUSE
220V-BROWN
12AF FUSE
110V-BLACK
BROWN
GREEN
BLUE
L1
L2
REJECTER
3
2
AC2
AC1
100V GREEN
110V RED
220V BLUE
100V GREEN
110V RED
220V BLUE
1
M-
Transformer
M+
WHITE
BLACK
YELLOW
AC MOTOR
GREEN
WHITE
BLUE
RED
VR
WHITE
BROWN
3 1 2
CON3
GREEN
Connector
BLACK
BROWN
110V (1AT FUSE)
220V (0.5AT FUSE)
BROWN
Driver Board
Upper Electronic
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
Assy
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement