SportsArt E875-16 Owner Manual

SportsArt E875-16 Owner Manual
E875-16 OWNER’S MANUAL CONTENTS
SENZA SERIES DISCLAIMER TERMS ...............................................
2
1. INTRODUCTION ................................................................................ 3
2. SAFETY PRECAUTIONS ..................................................................
4
3. LIST OF PARTS .................................................................................
4. ASSEMBLE THE PRODUCT ..........................................................
STEP 1 Secure the Pedestal................................................................
STEP 2 Install the Moving Parts ..........................................................
STEP 3 Install the Supports ................................................................
STEP 4 Install the Stationary Handlebars ..........................................
STEP 5 Install the Stoppers and Covers .............................................
STEP 6 Install the Pedals ....................................................................
STEP 7 Move the Product into Place ..................................................
STEP 8 Level the Product ..................................................................
STEP 9 Install the Power Cord ...........................................................
STEP 10 TV Terminal and Network .....................................................
STEP 11 Install the TV cable ...............................................................
STEP 12 Beware of Moving Parts ......................................................
5. UNDERSTAND THE E875 16” SENZA CONSOLE .........................
DISPLAY Overview ..............................................................................
DISPLAY Keys .....................................................................................
DISPLAY Windows ...............................................................................
9
11
11
12
14
15
16
17
18
19
20
21
22
23
24
24
24
24
6. OPERATE THE PRODUCT ..............................................................
OPERATION Safety Operating Area .....................................................
OPERATION Proper Workout Position and Safety Get Off ...................
OPERATION Overview ..........................................................................
OPERATION Start Screen ....................................................................
OPERATION Start Your (GO) Workout ..................................................
OPERATION Workout Selection ............................................................
OPERATION Workout Programs ...........................................................
OPERATION Workout Status ................................................................
OPERATION Select Entertainment .......................................................
OPERATION View Entertainment .........................................................
OPERATION Workout Summary ...........................................................
OPERATION Idle Mode ........................................................................
OPERATION Energy Smart Function ...................................................
OPERATION Precautions ......................................................................
25
25
26
27
27
28
28
29
30
31
32
33
33
33
33
7. ABOUT HEART RATE DETECTION .................................................. 34
HEART RATE Telemetry ........................................................................ 34
HEART RATE Contact ........................................................................... 34
8. GUIDELINES FOR EXERCISE ......................................................... 35
9. MAINTENANCE ................................................................................
MAINTENANCE Safety Precautions .....................................................
MAINTENANCE Error Messages ..........................................................
MAINTENANCE How to Replace a Fuse ..............................................
MAINTENANCE Lubrication ..................................................................
MAINTENANCE Lubrication Procedure ................................................
36
36
36
37
38
38
E875-16 OWNER’S MANUAL CONTENTS
MAINTENANCE Cleaning the Glide Rails ............................................
MAINTENANCE Schedule ....................................................................
MAINTENANCE Task List .....................................................................
MAINTENANCE One-Year Maintenance Log .......................................
40
41
42
43
10. ACCESSORIES ............................................................................ 44
ACCESSORIES Entertainment Cap ..................................................... 45
11. APPENDIXES ................................................................................. 46
APPENDIXES Specifications ............................................................... 46
APPENDIXES Electronics Block Diagram ........................................... 47
2
SENZA series disclaimer terms
A.
Internet function:
A1. This machine provides only a web page browsing method for web page
and video browsing.
A2. For web page videos, we support only Youku and YouTube.
Note: Some videos may not be viewed due to restrictions resulting from country policies, internal server firewalls, or video formats, etc.
B.
IPTV:
This function is not available yet.
C.
USB Video:
This function is not available yet.
D.
Bluetooth functions:
D1. Bluetooth Music (AVRCP V1.5)
Due to the many varieties of, and rapid changes in, mobile phone models,
failure of a mobile phone to connect indicates that we currently do not
support that phone.
D2. Bluetooth BLE 4.0 Heart Rate Strap
We only support POLAR-compliant Bluetooth BLE 4.0 Heart Rate Straps.
E.
TV:
E1. This machine only supports viewing local free TV.
E2. This machine may be affected by the local environment, climate,
equipment, etc., which may cause poor quality in reception and definition.
F.
This machine does not support the installation of third-party APPs, which may affect its operating stability.
G.
If any difference in content is found between this manual and the machine, please contact the local distributor for an electronic manual.
H.
USB charger
Supports charging of GOOGLE-certified Android mobile phones, and Apple iPhone, iPad, iPad air, and iPad mini.
L.
CSAFE
This function is not available yet..
2
1. INTRODUCTION
Congratulations on your purchase of one of the finest exercise products on the
market today, the SportsArt E875 16” Senza Console Elliptical trainer. Constructed
of high quality materials and designed for years of reliable usage, this product was
made to become an integral part of your commercial fitness venue.
Before this product is assembled or operated, we recommend that you familiarize
yourself with this manual. Understanding the correct assembly and operation of
this product will help ensure that exercisers obtain their fitness goals safely and
successfully.
R
L
3
2. safety Precautions
Your SportsArt elliptical trainer was designed and built for optimum safety. However
certain precautions apply whenever you use your elliptical trainer.
Please read the entire manual before assembly and operation. Also, please note the
following safety precautions:
●● Please read the instructions carefully and install the elliptical trainer as instructed.
●● Assemble and operate the elliptical trainer on a solid, level surface. DO NOT use
outdoors or near water.
●● Never allow children 12 or younger on or near the elliptical trainer.
●● Check the elliptical trainer before every use. Make sure all parts are assembled,
and all fasteners are tightened. DO NOT use the elliptical trainer if the unit is
disassembled in any way.
●● Keep your hands away from moving parts.
●● Wear proper workout clothing; DO NOT wear loose clothing. DO NOT wear
shoes with leather soles or high heels. Tie all long hair back. DO NOT go barefoot
on this product.
●● Be careful when mounting and dismounting the unit.
●● The elliptical trainer may or may not stop immediately if an object becomes caught
or impedes normal motion.
●● Do not use accessories or parts that are not specifically recommended by the
manufacturer (SportsArt). Such parts might cause injuries or cause the unit to fail
and void the warranty. We will not be responsible for any safety issue that arises
due to the misuse of accessories or parts. At the same time, we will terminate the
warranty terms of this equipment.
●● Close supervision is necessary when this elliptical trainer is used by, on, or near
children 12 or younger, invalids, or disabled persons.
●● Use this elliptical trainer only for its intended use as described in this manual.
●● Never operate this elliptical trainer if it has been damaged in any way. If it is not
working properly, or has been dropped or damaged, contact your dealer.
●● Keep all air ventilation areas free of blockage.
●● Never drop or insert any object into any opening.
●● DO NOT operate where aerosol (spray) products are being used or where oxygen
is being administered.
●● The general user weight limit for this elliptical trainer is 227kg (500lb). Note that
at resistance level 40 this product meets standards for users of up to 150kg (330lb).
4
2. safety Precautions (Continued)
●● This elliptical trainer is not intended for use by persons (including children
12 or younger,) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or
instruction concerning use of this elliptical trainer by a person responsible
for their safety.
●● Children 12 or younger should be supervised to ensure that they do not
play with the elliptical trainer.
●● Maintenance and repair must be performed by trained service personnel
only. Improper maintenance would not only damage the machine, but also
may present a danger to the exerciser.
●● Warning that any of the adjustment devices that could interfere with the
user’s movement should not be left projecting.
Caution
If you feel any pain or abnormal sensation, STOP YOUR WORKOUT and
consult your physician immediately. Work within your recommended exercise level. DO NOT work to exhaustion.
Before beginning any exercise program, you should consult with your doctor. It is recommended that you undergo a complete physical examination.
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If the user desires to correct such interference, it is at the user’s own expense.
Warning
Heart rate monitoring systems may be inaccurate. Over exercise may
result in serious injury or death. If you feel faint, stop exercise immediately
and consult a medical physician.
5
2. safety Precautions (Continued)
If you are a French speaking person in North America, please place the
following label contained in the owner’s manual on the console as shown.
Customers outside of North America will not receive this French warning
label.
(Note: If there are any other warning labels contained in the owner’s manual,
please place them on the clearly displayed location on the console as well.)
6
2. CONSIGNES DE SÉCURITÉ IMPORTANTES
• Votre vélo SportsArt a été conçu et fabriqué afin d’assurer une sécurité
optimale. Cependant certaines précautions s’appliquent chaque fois que
vous utilisez votre vélo de course.
• Lisez entièrement le manuel avant l’assemblage et l’utilisation. Veuillez
aussi noter les consignes de sécurité suivantes:
• Veuillez lire attentivement les instructions et installer le vélo de course
selon les instructions.
• Assemblez et faites fonctionner le vélo sur une surface solide et plane;
NE PAS l’utiliser à l’extérieur ou près de l’eau.
• En aucun cas, ne laissez des enfants à proximité ou sur le vélo.
• Vérifiez le vélo de course avant chaque utilisation. Assurez-vous que
toutes les pièces sont assemblées, et que tous les éléments de fixation
sont serrés. NE PAS utiliser le vélo de course si l’appareil est démonté de
quelque façon.
• Gardez vos mains loin des pièces mobiles.
• Portez des vêtements d’entraînement appropriés; NE PORTEZ PAS de
vêtements amples. NE PORTEZ PAS de chaussures à semelles en cuir
ou à talons hauts. Attachez les cheveux longs. Ne marchez pas pieds nus
sur l’appareil.
• Soyez prudent lors du montage et démontage de l’appareil.
• Le vélo peut s’arrêter ou ne s’arrêter pas immédiatement si quelque
chose obstacle le mouvement.
• NE PAS utiliser d’accessoire non spécifiquement recommandé par le
fabricant. Car cela pourraient provoquer des blessures ou entraîner une
panne de l’appareil.
• Une surveillance étroite est nécessaire quand le vélo est utilisé par ou à
proximité d’enfants, de malades ou de personnes handicapées.
• Utilisez le vélo de course uniquement pour l’usage prévu dans ce manuel.
• N’utilisez jamais le vélo de course s’il a été endommagé de quelque
façon que ce soit. S’il ne fonctionne pas correctement, ou s’il est tombé ou
endommagé, contactez votre vendeur.
• Veillez à ce qu’aucun orifice de ventilation ne soit obstrué.
• Ne faites jamais tomber ou n’insérez jamais d’objet dans les orifices.
• NE PAS l’utiliser là où des produits aérosols (vaporisés) sont utilisés ou
lorsque de l’oxygène est administré.
• La limite de poids de l’utilisateur pour cet vélo est de 227 Kgs (500 lbs).
Remarquez que la résistance de 40 convient jusqu’à 150kgs (330 lbs).
• NE PAS transporter le vélo de course par le cordon d’alimentation et
n’utilisez pas le cordon comme poignée.
• Maintenez le cordon éloigné de toute surface chaude.
• Débranchez l’appareil de la prise avant l’entretien ou la suppression de
toute pièce.
• Pour diminuer le risque de choc électrique, débranchez toujours ce vélo
de course de la prise de courant, immédiatement après utilisation et avant
le nettoyage.
7
2. Consignes de sécurité (Suite)
Ce vélo n’est pas destiné à être utilisé par des personnes (y compris des enfants)
dont les capacités physiques, sensorielles ou mentales sont réduites ou qui ne
disposent pas de l’expérience ou du savoir nécessaires, sauf si celles-ci ont au
préalable été formées eu égard à l’utilisation de ce vélo par une personne responsable de leur sécurité. Les enfants doivent être encadrés afin d’empêcher qu’ils ne
jouent avec le vélo.
ATTENTION
Si vous ressentez une douleur ou si vous avez une sensation anormale,
ARRÊTEZ VOTRE ENTRAÎNEMENT et consultez immédiatement votre médecin.
Entraînez-vous à votre niveau d’exercice recommandé. NE PAS s’entraîner jusqu’à
l’épuisement.
Avant de commencer un programme d’exercice, vous devriez consulter votre
médecin. Il est recommandé de faire un examen physique complet.
Remarque: Ce matériel a été testé et déclaré conforme aux normes des appareils
digitaux de Classe A, conformément à la partie 15 du Règlement de la FCC. Ces
limites sont conçues pour offrir une protection raisonnable contre les interférences
nuisibles dans une installation résidentielle. Cet appareil génère, utilise, et peut
diffuser des signaux radioélectriques, et, s’il n’est pas installé et utilisé conformément
aux instructions, peut provoquer des interférences nuisibles aux communications
radio. Cependant, il n’y a aucune garantie que des interférences ne se produiront
pas dans une installation particulière.
Si l’utilisateur désire corriger les interférences, ces corrections seront à la charge de
l’utilisateur.
Dans ce manuel, les mots “gauche” et “droit” sont utilisés en référence aux pièces et
au produit. Comme tels, les mots “gauche” et “droit” font respectivement référence
aux côtés gauche et droit de l’exerciseur. De même pour plus de concision, le
mot est utilisé dans certains cas où des rondelles, des vis et autres matériels sont
associés.
ATTENTION!
Les systèmes de surveillance de la fréquence cardiaque peuvent s’avérer imprécis.
Un entraînement excessif risque de nuire sérieusement à la santé ou d’entraîner la
mort. En cas d’étourdissement, arrêtez immédiatement l’entraînement.
• Un branchement incorrect du connecteur de mise à la terre de
l’équipement risque d’entraîner un choc électrique. En cas de doute sur la
mise à la terre correcte de vélo, faites appel à un technicien ou un électricien qualifié. NE PAS modifier la fiche fournie avec l’elliptique, si elle ne
correspond pas à la prise, faites installer une prise adéquate par un technicien qualifié.
• Les enfants doivent être encadrés afin d’empêcher qu’ils ne jouent avec
le vélo.
8
3. LIST OF PARTS
Assembly Parts
No.
Name
Qty. No.
Name
Qty.
A1 Main frame
1
A8 Support tube, left
1
A2 Stationary handlebar
1
A9 Support tube, right
1
1
A10 Pedals
1
A4 Joint cover, left
1
A11 Hardware kit
1
A5 Joint cover, right
1
A12 Power cord
1
A6 Rear roller cover
1
A13 TV Terminal
1
A7 Left roller cover
1
A14 French Sticker (For USA)
1
A3
Pedestal covers, left and
right
9
3. LIST OF PARTS (continued)
Components in the Hardware Kit
No.
10
11
12
13
14
Name
Qty.
Mushroom top inner hex screw
Spring washer
Washer
Stride adjustment linkage cover
Hex nut
Stopper
Round head Phillips screw
Secondary roller bolt
Self-lubricating bushing
Secondary roller
L-shaped Allen wrench
L-shaped Allen wrench
T-shaped Allen wrench
Double open-end wrench
Double open-end wrench
Screwdriver handle
Screwdriver shank
6
6
6
2
2
2
4
2
4
2
1
1
1
1
1
1
1
Specification
Notes
M10*P1.5*L25
M10
D21*d10.5*t1.5
M10*P1.5
30-30
M4*L12
D9.96*L67
D58*t23
M4
M5
M6
(8*17)
(14*15)
Green
Flat and Phillips
Components on the Product
No.
21
Name
Specification
Phillips screw
M4*P0.7*L8
Inner hex screw
Flat washer
Inner hex screw
Handlebar washer
Mushroom top inner hex screw
Spring washer
Inner hex screw
Handlebar washer
5/16”*L2-1/4” half
D20*d8*t2.0
M6*L15
D20*d7*t2.0
M8*L15
M8
M6*L15
D20*d7*t2.0
26
Phillips screw
M5*P0.8*L15
27
Mushroom top Phillips screw
M5*P0.8*L12
28
Inner hex screw
M5*L16
29
Phillips screw
M4*P0.7*L8
22
23
24
25
10
Notes
4. ASSEMBLE THE PRODUCT
Follow instructions below to assemble this product. Note that in this manual
the words “left” and “right” are used to refer to the product and its parts. As
such, these designations correspond to the “left” and “right” sides of a person in position to exercise on this product. Also, for brevity, the word “screws”
is used where screws, washers, and other hardware may be involved.
STEP 1 Secure the Pedestal
Please follow instructions (a) through (b) to secure the pedestal.
(a) Lift the pedestal (A1).
(b) Secure screws (10) in sequence. Secure screws in area A, followed by
those in area B. Then secure screws in area C, followed by those in area
D.
(a)
(b)
11
STEP 2 Install the Moving Parts
Follow instructions (a) through (e) to install the moving parts.
(a) Remove screws (21) from the stride arm attached to the main frame (A1).
(b) Once slip the glide rail into (Part A) and then place the pedal carriage
lightly on the glide rail support.
(c) Connect the guide roller (14) on the bottom of the glide rail. (Please note
the direction to insert the screw is from outside to inside.).
(a)
(b)
A
(c)
12
STEP 2 Install the Moving Parts (Continued)
(d) Separate the roller covers (A7). Snap them together into place on the
product. The secure them with screws (21).
(e) On the left side of the product, remove the screw (22) from the stride
adjustment linkage. Place the stride adjustment linkage into place on the
bushing, and use the screw (22) to secure it into place. Then press the
stride adjustment linkage cover (11) into place. Carry out the same
procedure on the right side of the product as well.
(d)
(e)
Warning: Consult the manual and follow all assembly instructions carefully. Please note that incorrect assembly
may present a danger to the exercise, will damage the elliptical and void the warranty.
13
STEP 3 Install the Supports
Follow steps (a) through (b) to secure the support tubes.
(a) Remove support tube screws (23) (24) from the main frame (A1).
(b) Insert left and right support tubes (A8) (A9) onto the axle area and base,
and loosely secure them into place with screws (23) (24).
(a)
(b)
14
STEP 4 Install the Stationary Handlebars
Follow instructions (a) through (c) to install the handlebars.
(a) First, please remove screws (25) from the left and right support tubes (A8)
(A9), then attach the stationary handlebar to the main frame and use
screws (25) to secure the assembly shown in area (A).
(b) Remove screws (26) from the sides of the left and right support tubes
(A8) (A9), then lock both left and right joint covers (A4) (A5) onto the
connection with screws (26) and the covers.
(c) Tighten the screws in area (B), then push down the support tubes to its
secure position.
(a)
(b)
(c)
15
STEP 5 Install the Stoppers and Covers
Follow steps (a) through (c) to install glide rail stoppers and covers.
(a) Screw stoppers (12) into place on both glide rails.
(b) Remove screws (27) from the main frame (A1).
(c) Snap pedestal covers (A3) together on the unit. Loosely secure screws
(27), followed by screws (13). After all screws are in place, secure them.
(a)
(b)
(c)
16
STEP 6 Install the Pedals
Follow steps (a) through (b) to install the pedals.
(a) Remove screws (28) from the pedal carriage as shown.
(b) Detach and lift the front and back part of the pedals cushion without
detaching the center Area (A). Use screws (28) to secure the pedals
onto its mount on the pedal carriage. Secure area B first, then secure
area C. Insert the nibs on the cushion through the holes in the pedals.
Make sure that the nibs protrude through the pedals (A10).
(a)
(b)
17
STEP 7 Move the Product into Place
There are two techniques for moving this product.
(a) One person: Grip the front base of the product and lift upward, then push
the product into location for use. Be careful to avoid pinching fingers
when setting the product down.
(b) Two people: Have one person grip the front base of the product while
the other person grips the support tubes (A8) (A9). With both people
lifting and stabilizing the unit, roll it into place for use. Be careful to avoid
pinching fingers when setting the product down.
Note: Please do grip the front base of the product as indicated by the arrows
as below.
(a)
(b)
18
STEP 8 Level the Product
For the user’s safety and the proper functioning of the product, this elliptical
trainer must sit level on a flat floor. If necessary, adjust the levelers by
following instructions (a) through (c) below.
(a) Loosen the leveler nut.
(b) Rotate the leveler foot downward so it firmly touches the floor.
(c) To secure this position, secure the leveler nut upward against the product
frame.
(a)
(b)
19
(c)
STEP 9
Install the Power Cord
(a) First remove screws (29) from the power cord socket on the product.
(b) Insert the power cord into place on the product.
(c) Secure power cord connector screws (29) and then insert the other end
of the power cord (A12) into the appropriate power supply socket in the
wall.
20
STEP 10 TV Terminal and Network
(a) NETWORK: Connect to Ethernet.
(b) AV Terminal: Connect to DVD Player or Media Player.
(c) TV: Connect to ATV (NTSC or PAL) or DTV.
(a)
(b)
21
(c)
STEP 11 Install the TV Cable
NTSC system: Directly connect your local area connector as shown.
PAL system: Insert NTSC To PAL Adapter (30) as shown and connect to
your local area connector.
22
STEP 12 Beware of Moving Parts
This product has moving parts that could be a danger to people and animals.
During use, do not insert hands or other objects into the stride adjustment
slot, the opening in the rear cover, or other areas in which such action might
present a hazard.
23
5. UNDERSTAND THE Senza Console
DISPLAY Overview
E875 Series 16” Senza Console are designed to help users obtain their fitness goals in a simple and convenient way. Before using the elliptical trainer,
please familiarize yourself with the functions of this display console to obtain
optimum benefits and enjoyment from this product.
DISPLAY Keys
Information on control panel buttons and functions are shown in the following diagram.
No. Name of button
1
2
Function
When the machine is in the Energy Smart conEnergy Smart
servation mode, pressing this button will wake up
Wake-Up Button
the machine and turn the power on again.
The user can listen to audio or music after insertHeadphone Jack
ing a headphone
DISPLAY Windows
Information
SPEED
RESISTANCE LEVEL
STRIDE LENGTH
TIME
DISTANCE
CALORIES
CALORIES/HOUR
HEAR RATE RANGE
METS
PACE
TOTAL STRIDES
SPM/MIN
WORKOUT
PROGRAM
Specifications
0.1 mph (kph)
1 ~ 40
450 ~ 730mm or 17” ~ 29”
0:00 ~ 600:00
0.00 ~ 9999 Miles (Km)
0 ~ 9999 Kilocalorie
0 ~ 9999 Kilocalorie
35 ~ 220 bpm
Metabolic equivalent of task: 0.0 to 99.0
1 / SPEED
0 ~ 9999
5 ~ 150
QUICK START
PLATEAU
INTERVAL
SENZA JOURNEYS
VARI STRIDE
HEART RATE
24
6. OPERATE THe PRODUCT
OPERATION Safety Operating Area
(a) Safety clearance required as below shown. Do not allow people to be
near this area when operating.
(b) Noise emission under load is higher than without load.
25
OPERATION Proper Workout Position and Safety Get Off
(a) User proper workout position as below shown.
(b) Over exercise or improper workout position may result in serious injury.
(c) User can hold onto handles for stability when getting on or getting off
from the right/left side of the elliptical.
(d) This product is intended for exercise arms and legs.
26
OPERATION Overview
Touch screen design is simple and clear. The screen layout helps users
focus on exercise. It provides many workout modes that can help you achieve
your fitness goal. The following sections introduce information concerning
touch screen operation, the available types of workout, and how to start the
workouts.
OPERATION Start Screen
This screen will appear when the machine is turned on.
Description of start screen buttons
No. Name of button
Function
1 Date and Time
Displays the current time and date
2 SA WELL+
Touch to login into the SA WELL+ system
Touch for pairing with Bluetooth or ANT+ heart rate
3 HR SELECT
strap
LANGUAGE
Touch to select your preferred language by country
4
SETTING
Touch to switch screen to black and white display
(with high contrast).
5 DISPLAY MODE
Touch again, the screen will switch back to color
display
Touch to access the engineering mode. This is the
ENGINEERING maintenance setting for use by technicians. Pass6
SETTING
word input is required to perform the actions of the
related settings
CUSTOMIZED
Web page status display for browsing and opera7 WEB PAGE
tion
WINDOW
Touch this button to access workout program se8 SELECT
lection
27
OPERATION Startup Screen (Continued)
No. Name of button
9
FEATURE
10
GO
Function
Displays various virtual realities. Touch this screen
to access the virtual reality training mode
Touch this button to start workout
OPERATION Start Your (GO) Workout
By using the (GO) workout, exercise is started in the manual workout mode.
The default user age is 35 and default weight is 75 kg (165 lbs). You can proceed by using these default settings or change the settings.
How to start the (GO) workout:
1. Touch the (GO) button
A 3, 2, 1, GO countdown will appear on the screen, and the elliptical
trainer will start.
2. During the workout, if you choose to stop the workout, the “Workout
Summary” screen will display the workout status for the session.
OPERATION Workout Selection
Touch the “SELECT” button on the start screen to access “SELECT
WORKOUT”.
Operation method: Slide finger on screen to move the selection list. Various
workout programs are available for selection, from left to right these are
QUICK START, PLATEAU, INTERVAL TRAINING, SENZA JOURNEYS,
VARI STRIDE and HEART RATE TEST. Once a program is selected, the
screen will start a 3-second countdown and the workout will begin. During
a workout, the user can switch to a different workout program.
Note: With exceptions for Heart Rate Test programs of which settings must
be selected in advance prior to the workout.
28
OPERATION Workout Selection (Continued)
Description of icons on the “Select” screen
ICON
Description
Tap to return startup screen. During exercising, tap it to stop
or resume workout.
Quick Tools
OPERATION Workout Programs
Workout program details are explained below.
QUICK START
A workout mode option based on time, distance and calories that allows user
to start a workout immediately.
PLATEAU
Various workout mode options are provided to achieve workout goal.
INTERVAL (1:1, 1:2, 2:2)
Interval Training is alternating periods of high intensity aerobic exercise and
low intensity aerobic exercise.
Workout time ratios have 3 options, namely 1:1, 1:2 and 2:2.
SENZA JOURNEYS
Built-in or customized landscape films allow the user to watch a video of
scenery while exercising.
VARI STRIDE
This workout program automatically changes stride.
HEART RATE
A workout mode using heart rate as the target value.
29
OPERATION Workout Status
During the workout, you can select the “VIEW Dashboard” page below the
screen to check the exercise status of your workout process. There are a
total of 9 status windows for various information views, and you can modify
the information display format in the status windows by touching the▼symbol
below the status windows. A drop down menu for information display format
will be opened for selection.
Drop down menu introduction:
Symbol
Drop Down Menu Items
Default
Other Options
Average Resistance
Resistance
Watts
Change Resistance
Total Stride
Speed
Stride Length
Pace
Average Speed
Change Stride Length
Time Remaining
Clock
Time Elapsed
Segment Duration
Target Duration
Segment Duration
Segment Remaining Time Elapsed
Time Remaining
Average Heart Rate
Heart Rate
Max Heart Rate
Set Target Heart Rate
30
OPERATION Workout Status (Continued)
Symbol
Drop Down Menu Items
Default
Other Options
Total Distance
Distance Remaining
Calories
Calories/Min
Calories/Hour
Mets
SPM
Average SPM
OPERATION Select Entertainment
You can select the “Select Entertainment” page below the screen, and the
available multimedia features will be displayed. The features include TV, Internet, SENZA Journeys, Bluetooth Audio, IPTV and AVIN, etc.: the small
central window will display the selected multimedia screen immediately.
Note: 1. At least 10Mbps Internet Speed is required in watching videos on YouTube or any other websites.
2. 10/100Mbps Base-T router is recommended for this product. If your
router is 1000Mbps Base-T, ensure setting the port speed of the
internet port to 10 Mbps or 100 Mbps.
31
OPERATION View Entertainment
The display mode that maximizes the selected multimedia capabilities; in
addition to the multimedia display, a sidebar workout information display is
also included, so the user can check their current workout status instantly
while using the multimedia features.
Description of Icons in the “Entertainment” screen
Icon
Description
Full Screen (Exit full screen mode by tapping screen.)
Mute
Lower volume
Raise volume
Slow reverse
Play
Fast Forward
32
OPERATION Workout Summary
At the end of a workout or when you press the stop button, the workout summary screen will appear. The screen shows your current workout status.
OPERATION Idle Mode
When the elliptical trainer stops running with no other activity for 2 minutes,
the machine will enter the idle mode and the display will randomly show the
standby picture. Touch any position in the idle mode to enter the Home page.
Note: The standby picture can be changed and set by the user.
OPERATION Energy Smart Function
There is a default Energy Smart timer setting feature in the engineering mode.
When the elliptical trainer is not in use and the set up time for power saving
is reached, the system will automatically enter the power saving mode, the
Energy SMART light will change from green to orange, and the whole screen
will turn dark. Press the Wake Up button to turn the power back on.
OPERATION Precautions
1. Turning the product on and off every day will make your software system
refresh and stable and ensure waiting 5 minutes to turn on the product
when you restart each time.
2. SanDisk USB (Fat32, MAX 32GB) is recommended for updating the
program.
33
7. ABOUT HEART RATE DETECTION
Heart rate detection functions are selected at the time of purchase. Not every
product has every type of heart rate detection. The following explains factors
that influence the performance of two of the most common types of heart rate
detection devices.
HEART RATE Telemetry
The words “telemetry heart rate” refer to the detection of heart rate via a device
worn on the exerciser and transmitted over the air to a circuit board built into the
product. Telemetry heart rate devices are commonly worn on the exerciser’s
chest, where the pulse is strongest and relatively easy to detect.
The following explains conditions that affect the performance of the telemetry
heart rate function in all products.
●● The telemetry heart rate transmitter emits a wireless 5 kHz signal that is harmless to the human body. Inside the transmitter is a 3 V battery (CR2032). If the
battery voltage is too low, either the reception distance shortens or there will be
no reception whatsoever.
●● Secure the telemetry heart rate transmitter on your chest so that it stays in
place without making you feel uncomfortable. Moisten the skin for better contact.
●● Because the telemetry heart rate signal varies in strength from 20 Hz to 20
KHz, environmental interference can block signal reception. Physical vibration
and electronic devices, including stereos, TVs, and even fluorescent lights, can
interfere with signal reception. For best results, install the product in an area free
from such interference.
●● Space the product apart by at least 39 inches (100 cm) to avoid having the
heart rate value from one exerciser appear on a neighboring product.
HEART RATE Contact
The words “contact heart rate” refer to the detection of the heart rate via sensors
on the product. By holding the sensors, the exerciser can view his or her heart rate
on the product display. Like telemetry heart rate, contact heart rate can be influenced by several factors. The following list includes some of these factors.
●● A weak pulse makes it difficult to detect heart rate.
●● Low systolic blood pressure makes it difficult to detect heart rate.
●● Dry, course palms impede heart rate detection. For best results, moisten your
palms. But do not apply hand lotion immediately prior to your workout, because
hand lotion can gum up the contact pads.
Heart rate devices built into this product are not medical devices. Heart rate values
are for reference only. Do not use them for medical diagnostic or treatment work.
CAUTION: Heart rate detection and transmission devices have been known to
interfere with the operation of pacemakers, possibly endangering human life. If you
have a pacemaker, exercise under your doctor’s supervision; take a test to ensure
your safety during the simultaneous use of the pacemaker and heart rate detection
devices. The use of such devices must be undertaken at your own risk.
Note that in dry areas in particular, static electricity can interfere with unit operation
and shock people. To discharge static electricity from your body, touch something
else before touching metal on the product.
34
8. GUIDELINES FOR EXERCISE
HOW HARD SHOULD I EXERCISE?
Studies show that to benefit from aerobic exercise, people need to maintain a certain
heart rate during their workouts. Your heart rate training zone depends on your age
and fitness level.
The darkened area in the chart to the right represents the recommended heart rate
training zone for people of various ages. It was calculated by taking 220 minus age
in years, multiplied by 65% and 80%. The area between those values is the heart
rate training zone.
CAUTION: Heart rate training zones are
generalizations and may not suit every person.
Always check with your physician to understand what heart rate goal would be appropriate for you.
HE
HOW LONG SHOULD I EXERCISE?
The duration of your workout must depend
on your fitness level. In general, it is recommended that you maintain a heart rate within
your training zone for at least 15 to 20 minutes to experience the benefits of aerobic
exercise. Beginners should always start out slowly and gradually increase the
duration and intensity of their workouts. As your fitness level improves, you will be
able to maintain a heart rate within the training zone for longer periods of time.
When you begin your workout, use the first several minutes to warm up. Then slowly
increase the intensity of your workout to bring your heart rate into your training zone.
At the end of your workout, gradually decrease your workload. Then exercise lightly
to cool down.
HOW OFTEN SHOULD I EXERCISE?
Research indicates that to achieve the greatest benefit, people should exercise
three to five times per week. It is important to allow sufficient time, at least 24 hours,
for your body to recover after exercise.
35
9. MAINTENANCE
This section covers maintenance topics, including instructions on replacing
a fuse and lubricating the walk belt, along with the presentation of a maintenance schedule, maintenance task list, one-year maintenance log, and
electronics block diagram.
MAINTENANCE Safety Precautions
●● Please follow standard safety precautions when servicing on this product.
●● Maintenance and repair must be performed by trained service personnel
only. Improper maintenance would not only damage the machine, but also
may present a danger to the exerciser.
●● Electronic components can carry an electrical charge even after the product has been turned off. For safety, turn off unit power. Wait five minutes to
allow capacitors to discharge. Then disconnect the power cord from the wall
socket (if applicable.) Only after such steps have been completed should
covers be removed and electronic components accessed.
●● Unplug product and wait ten minutes before performing maintenance.
●● Do NOT use a damp towel to clean the product and do perform the following maintenances.
●● Do NOT use cleaners with alcohol, ammonia, or other damaging chemicals. The use of such chemicals can damage the product and void the warranty. Never spray or pour any liquid directly onto the product. Doing so can
damage electronic components and void the warranty.
●● Use a clean, lint-free towel, dampened with a mixture of Simple Green®
all-purpose cleaner, to thoroughly clean the handlebar and the console.
●● This product has moving parts that can be hazardous. Exercise caution
when maintaining, operating, or moving this product.
●● Do not use accessories or parts that are not specifically recommended
by the manufacturer (SportsArt) . Such parts might cause injuries or cause
the unit to fail and void the warranty. We will not be responsible for any
safety issue that arises due to the misuse of accessories or parts. At the
same time, we will terminate the warranty terms of this equipment.
●● This product shall be disconnected from its power source during service
and when replacing parts.
MAINTENANCE Error Messages
The following messages can appear on this product for diagnostic purposes.
ERROR 7 L, ERROR 7 R & ERROR 7 R/L - Indication: the stride mechanism is not calibrated properly. Contact a certified SportsArt technician. The
technician will need to either inspect the stride motor or the driver.
ERROR _8_1, ERROR _8_2 - Indication: There is a communication error
between control board and its driver. Contact a certified SportsArt technician. The technician will need to either inspect the stride motor or the driver.
Machine Model Unidentified - The machine model couldn’t be identified.
36
MAINTENANCE How to Replace a Fuse
If electrical current becomes too high, the fuse breaks. This protects the
product. To replace a fuse, follow instructions (a through g) below.
(a) Use a tool to press the fuse cap inward.
(b) Turn the fuse cap counterclockwise.
(c) The fuse cap springs out.
(d) Remove the burnt fuse.
(e) Insert a new fuse into the fuse cap.
(f) Insert the fuse into the fuse holder.
(g) Use a tool to rotate the fuse cap clockwise and secure it into place.
Fuse specifications: 110 V = 1 Amp, A(F); 220V = 1 Amp, A(F)
b
a
g
d
e
c
37
f
MAINTENANCE Lubrication
To enter Lubrication function, first you must set the console to the Lubrication
state. During Banner mode, the message shows “SELECT A PROGRAM”,
press STRIDE ▲ and STRIDE ▼ and STOP keys at the same time for 3
seconds to activate this procedure. Once Lubrication procedure is activated,
the stride motor will move to the correct position and the message will display “LUBRICATION”. At this time, it is ready for lubrication. Please follow
the lubrication procedure listed on the following page to start lubricating.
Once the lubrication procedure is completed, please follow below instruction
to return the stride length to 29”/730mm.
1. When the power is off, pedaling the elliptical to turn on the power.
Or 2. Press and hold the STOP key for 2 seconds to reset.
The lubrication process is now completed.
MAINTENANCE Lubrication Procedure
Please follow instructions (a) through (h) to lubricate the product.
(a) Remove the cap that covers the lubrication hole.
(b) Use an automobile grease gun to apply red lithium bearing grease into
the nozzle on the product.
(c) After applying lubricant, detach and remove the grease gun.
(d) Insert the cap back into place.
(a)
(b)
(c)
(d)
38
MAINTENANCE Lubrication Procedure (Continued)
(e) Push in at point A, and slide upward to remove the lubrication hole cover.
(f) Press the stride up key to adjust the stride to its longest point. Note the
grease fitting at area B.
(g) Use an automobile grease gun with red lithium grease. Apply the grease
to the nozzle on the product.
(h) Put the cover back into place, pushing inward at step 3 and downward at
step 4, as shown below. Note that point A provides the best contact sur
face on the lubrication hole cover.
(a)
(b)
(d)
(c)
39
MAINTENANCE Cleaning the Glide Rails
Clean the both left and right glide rails daily as follows:
(a) Use a clean, lint-free cloth to wipe dust and debris off the glide rails.
(b) Operate the product to inspect it and to determine where dirt might
remain on the glide rails.
(c) Repeat steps (a) and (b) two or three times to ensure smooth movement.
Note: Make sure to use a lint-free cloth
40
MAINTENANCE Schedule
Area
Day
Week
Month
Quarter
1 Exterior
Year
Notes
Clean
Inspect and secure
loose parts
Wipe away dirt and
debris.
Apply silicone lubricant.
2 Screws
3 Glide rail
4 Rollers
Stride
5
motor
Apply bearing grease.
Lubricate with original
66A lubricant.
6 Cushion
41
MAINTENANCE Task List (Elliptical Trainers)
Like cars, fitness products require maintenance. Regular maintenance extends product life, and failure to maintain products can void the manufacturer’s warranty. Copy the maintenance log sheet, and record maintenance
work for each fitness product.
Daily tasks
1. Use a clean, lint-free towel, dampened with a mixture of Simple Green®
all-purpose cleaner and water, to thoroughly clean the product exterior.
2. Inspect parts for looseness, and secure all loose screws. Make sure that
the product is safe for operation. If safety issues arise, place an “Out of
Order” sign on the product, and call for service.
3. Wipe dirt and debris off the glide rails. Use a clean, lint-free towel,
dampened with a mixture of Simple Green® all-purpose cleaner and
water.
Weekly tasks
1. Clean rollers. Use a clean, lint-free towel, dampened with a mixture of
Simple Green® all-purpose cleaner and water. Apply a small amount of
silicone lubricant onto the rollers.
Yearly tasks
1. Apply grease to the stride mechanism.
2. Apply SportsArt 66A lubricant to the cushion.
Caution
●● Please follow standard safety precautions when working on this product.
●● Electronic components can carry an electrical charge even after the
product has been turned off. For safety, turn off unit power. Wait five minutes
to allow capacitors to discharge. Then disconnect the power cord from the
wall socket (if applicable). Only after such steps have been completed
should covers be removed and electronic components accessed.
●● Do NOT use cleaners with alcohol, ammonia, or other damaging
chemicals. The use of such chemicals can damage the product and void
the warranty. Never spray or pour any liquid directly onto the product. Doing
so can damage electronic components and void the warranty.
●● This product has moving parts that can be hazardous. Exercise caution
when maintaining, operating, or moving this product.
42
MAINTENANCE One-Year Maintenance Log
Facility:_______________________ Supervisor:____________________
Product model number:__________ Serial number:_________________
Start date: ____________________ End date:_____________________
Daily Tasks
Completed
Weeks 1-7
Weeks 8-14
Weeks 15-21
Week 22-28
Daily Tasks
Completed
Week 29-35
Week 36-42
Week 43-49
Week 50-52
Weekly Tasks Weeks 1-7
Completed
Weeks 8-14
Weeks 15-21
Weeks 22-28
Weekly Tasks Weeks 29-35
Completed
Weeks 35-42
Weeks 43-49
Weeks 50-52
Monthly tasks 1
Completed
2
3
Quarterly Tasks
Completed
Quarter 1
Yearly Tasks
Completed
Year 1
4
5
Quarter 2
6
7
8
Quarter 3
9
10
11
12
Quarter 4
Notes: __________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
43
10. ACCESSORIES
These accessories are related to the functions of this machine. Some are
standard and others are optional.
The details of each accessory and its function are explained.
USB CHARGER (Standard)
The USB charger will provide 5V and 1.5A voltage for charging of smart
phone or other devices. However it is compatible only with some tablets,
such as iPad. Check your tablet for compatibility before charging.
CSAFE PORT (Standard)
Compatible with CSAFE (Communications Specification for Fitness Equipment) Protocol. It works with an optional Netpulse Personal Entertainment
System as well as the ECOFIT System.
SA WELL+ Member System (Option)
This is a system designed specially by SportsArt to assist the user in managing his/her workout history.
There are two ways to connect with the member site:
1. Use smart phone Bluetooth functions and the SA WELL+ App. The APP
software can be downloaded at APP Stores.
2. Supports USD flash drive to store workout data.
For more detailed information about the function, please visit the SA WELL+
website.
44
ACCESSORIES Entertainment Cap
(a) RFID member card slot: Work with both optional SA WELL+ and
ECOFIT member cards. (Not available yet.)
(b) Bluetooth/WIFI button: When a smart phone is connected with
equipment, press this button to disconnect. Scan the QR code or touch
the NFC tag on the console to connect to the equipment again if
necessary. (Available with optional SA WELL+.)
(c) USB port: This port is used for device charging as well as optional data
transferring. (Available with optional SA WELL+.)
(d) QR code and NFC tag: Use smart phone App to scan the QR code or
tap the NFC tag on the console to connect with equipment. (Available
with optional SA WELL+.)
(e) USB port: this port is used for device charging as well as media playing
such as MP3/MP4.
(a)
(b)
(d)
(c)
(e)
(d)
45
11. APPENDIXES
APPENDIXES Specifications
Model
Dimensions
Overall Weight
Maximum User Weight
Power Requirement
Fuse
Current Rating
E875 16”
L : 2200 mm (86.6”)
W : 710 mm (27.9”)
H : 1750 mm (68.8”)
164 kg (361 lbs)
150 kg (330 lbs)
100 – 120 V / 60 Hz (USA)
220 – 240 V / 50 Hz (EUROPE)
110 V : 1A
220 V : 1A
46
APPENDIXES Electronics Block Diagram
BT Board
Control Board
CSAFE Board
Main Board
TV Board
USB Board
HRC Board
Fan
Head Phone Board
NFC Board
EUP Key Board
Level switch
HTR Board
Stride switch
Contact HTR plates
Stepper motor
Speed sensor
Model no. board
DRV Board
Electro-magnet
EUP Board
Console power board
Fuse
AC Jack
Switch
Filter
:Connector
:Converge
47
AV Board
Your Authorized Distributor
48
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement