Samsung NZ84T9770EK User manual

Samsung NZ84T9770EK User manual
Induction Hob
User manual
NZ84T9770EK
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 1
2020-02-25
12:35:12
Contents
Contents
Using this manual
3
Operation
The following symbols are used in this User Manual:
Model name & serial number
3
3
Safety instructions
3
Disposing of the packaging material
Proper disposal of your old appliance
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
7
7
7
Installing the hob
8
Using the touch buttons
Switching the appliance on
Select cooking zone and power level setting
Switching the appliance off
Quick stop
Using the child safety lock
Timer
Using keep warm
Power boost
Power management
Pause
Flex control
Sound on/off
Suggested settings for cooking specific foods
Safety instructions for the installer
Connecting to the mains power supply
Installing into the countertop
Components
Before you start
Cooking zones
Control panel
Induction heating
The key features of your appliance
Safety shutoff
Virtual flame technology
Residual heat indicator
Temperature detection
Initial cleaning
Cookware for induction cooking zones
Suitability test
Size of pans
Operating noises
Using suitable cookware
8
8
9
11
12
12
12
13
13
14
15
15
15
16
16
16
16
17
17
18
18
18
18
19
19
19
20
21
22
22
22
22
23
23
Maintaining your appliance
24
Hob
Light soiling
Stubborn soiling
Problem dirt
Hob frame (option)
To avoid damaging your appliance
24
24
24
25
25
25
Warranty and service
26
FAQs and troubleshooting
Service
26
27
Technical data
28
Technical data
Cooking zones
Product information
28
28
28
2 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 2
2020-02-25
12:35:12
Safety instructions
Please take the time to read this owner’s manual, paying particular attention to the
safety information contained in the following section, before using your appliance.
Keep this manual for future reference.
If transferring ownership of the appliance, please remember to pass the manual on
to the new owner.
The safety aspects of this appliance comply with all accepted technical and safety
standards. However, as manufacturers we also believe it is our responsibility to
familiarize you with the following safety instructions.
The following symbols are used in this User Manual:
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
WARNING
Hazards or unsafe practices that may result in severe personal injury or death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or property
damage.
CAUTION
To reduce the risk of fire, explosion, electric shock, or personal injury when using
your hob, follow these basic safety precaution.
NOTE
Useful tips, recommendations, or information that helps users manipulate the
product.
Model name & serial number
Both the model name and the serial number are labeled underneath the hob base.
For later use, write down the information or attach the additional product label
(located on the top of the product) onto the current page.
Model Name
Serial Number
WARNING
Children should be supervised to ensure that they do not play
with the appliance.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
The means for disconnection must be incorporated in the fixed
wiring in accordance with the wiring rules.
English 3
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 3
2020-02-25
12:35:13
Using this manual
Using this manual
Safety instructions
Safety instructions
This Appliance should be allowed to disconnection from the
supply after installation. The disconnection may be achieved by
having the plug accessible or by incorporating a switch in the
fixed wiring in accordance with the wiring rules.
The appliance is not intended to be operated by means of an
external timer or separate remote-control system.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
The appliance must not be installed behind a decorative door in
order to avoid overheating.
The method of fixing stated is not to depend on the use of
adhesives since they are not considered to be a reliable fixing
means.
WARNING: If the surface is cracked, switch off the appliance to
avoid the possibility of electric shock.
CAUTION: The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
WARNING: The appliance and its accessible parts become hot
during use. Care should be taken to avoid touching heating
elements. Children less than 8 years of age shall be kept away
unless continuously supervised.
During use the appliance becomes hot. Care should be taken to
avoid touching heating elements inside the hob.
WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in a fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
WARNING: Accessible parts may become hot during use. Young
children should be kept away.
WARNING: Danger of fire: Do not store items on the cooking
surfaces.
A steam cleaner is not to be used.
WARNING: Use only hob guards designed by the manufacturer
of the cooking appliance or indicated by the manufacturer
of the appliance in the instructions for use as suitable or hob
guards incorporated in the appliance. The use of inappropriate
guards can cause accidents.
Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
After use, switch off the hob element by its control and do not
rely on the pan detector.
4 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 4
2020-02-25
12:35:13
The surfaces are liable to get hot during use.
user maintenance shall not be made by children unless they are
older than 8 and supervised.
Keep the appliance and its cord out of reach of children less
than 8 years.
Be sure the appliance is properly installed and grounded by a
qualified technician.
The appliance should be serviced only by qualified service
personnel. Repairs carried out by unqualified individuals may
cause injury or serious malfunction. If your appliance is in need
of repair, contact your local service centre. Failure to follow
these instructions may result in damage and void the warranty.
Flush - mounted appliances may be operated only after they
have been installed in cabinets and workplaces that conform
to the relevant standards. This ensures sufficient protection
against contact for electrical units as required by the essential
safety standards.
If your appliance malfunctions or if fractures, cracks or splits
appear:
• switch off all cooking zones;
• disconnect the hob from the mains supply; and
• contact your local service centre.
If the hob cracks, turn the appliance off to avoid the possibility
of electric shock. Do not use your hob until the glass surface
has been replaced.
English 5
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 5
2020-02-25
12:35:13
Safety instructions
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
CAUTION
Safety instructions
Safety instructions
Do not use the hob to heat aluminium foil, products wrapped
in aluminium foil or frozen foods packaged in aluminium
cookware.
Always keep the control panels clean and dry.
Liquid between the bottom of the pan and the hob can produce
steam pressure. Which may cause the pan to jump.
Cables from electrical appliances must not touch the hot surface
of the hob or hot cookware.
Always ensure that the hotplate and the base of the pan are
kept dry.
Do not use the hob to dry clothes.
Never place combustible items on the hob, it may cause fire.
There is the risk of burns from the appliance if used carelessly.
Keep all packaging materials well out of the reach of children,
as packaging materials can be dangerous to children.
Users with Pacemakers and Active Heart Implants must
keep their upper body at a minimum distance of 30 cm from
induction cooking zones when turned on. If in doubt, you
should consult the manufacturer of your device or your doctor.
(Induction hob model only)
This appliance is to be used only for normal cooking and frying
in the home. It is not designed for commercial or industrial use.
Do not attempt to repair, disassemble, or modify the appliance
yourself.
Never use the hob for heating the room.
Always turn the appliance off before cleaning.
Take care when plugging electrical appliances into mains
sockets near the hob. Mains leads must not come into contact
with the hob.
Clean the hob in accordance with the cleaning and care
instructions contained in this manual.
The cooking zones will become hot when you cook.
Always keep small children away from the appliance.
Overheated fat and oil can catch fire quickly. Never leave
surface units unattended when preparing foods in fat or oil, for
example, when cooking chips.
Keep pets away from the appliance because pets may step on
the controls of the appliance, causing an malfunction.
Turn the cooking zones off after use.
6 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 6
2020-02-25
12:35:13
Disposing of the packaging material
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
WARNING
All materials used to package the appliance are fully recyclable. Sheet and hard
foam parts are appropriately marked. Please dispose of packaging materials and
old appliances with due regard to safety and the environment.
WARNING
Before disposing of your old appliance, make it inoperable so that it cannot be a
source of danger. To do this, have a qualified technician disconnect the appliance
from the mains supply and remove the mains lead.
The appliance may not be disposed of in the household rubbish.
Information about collection dates and public refuse disposal sites is available
from your local refuse department or council.
For information on Samsung’s environmental commitments and product-specific
regulatory obligations, e.g. REACH, WEEE, Batteries, visit : samsung.com/uk/
aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.html
English 7
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 7
2020-02-25
12:35:13
Safety instructions
Proper disposal of your old appliance
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature
indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed
of with other household waste at the end of their working
life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where
they purchased this product, or their local government
office, for details of where and how they can take these
items for environmentally safe recycling.
Business users should contact their supplier and check the
terms and conditions of the purchase contract. This product
and its electronic accessories should not be mixed with
other commercial wastes for disposal.
Installing the hob
WARNING
Be sure the new appliance is installed and grounded only by qualified personnel.
Please observe this instruction. The warranty will not cover any damage that may
occur as a result of improper installation.
Technical data is provided at the end of this manual.
Safety instructions for the installer
•
Installing the hob
•
•
•
•
•
•
•
•
•
•
A device must be provided in the electrical installation that allows the
appliance to be disconnected from the mains at all poles with a contact
opening width of at least 3 mm. Suitable isolation devices include line
protecting cut - outs, fuses (screw type fuses are to be removed from the
holder), earth leakage trips and contactors.
With respect to fire protection, this appliance corresponds to EN 60335 - 2 6. This type of appliance may be installed with a high cupboard or wall on one
side.
The installation must guarantee shock protection.
The kitchen unit in which the appliance is fitted must satisfy the stability
requirements of DIN 68930.
For protection against moisture, all cut surfaces are to be sealed with a
suitable sealant.
On tiled work surfaces, the joints in the area where the hob sits must be
completely filled with grout.
On natural, artificial stone, or ceramic tops, the snap action springs must be
bonded in place with a suitable artificial resin or mixed adhesive.
Ensure that the seal is correctly seated against the work surface without any
gaps. Additional silicon sealant must not be applied; this would make removal
more difficult when servicing.
The hob must be pressed out from below when removed.
A board can be installed underneath the hob.
The ventilation gap between the worktop and front of the unit underneath it
must not be covered.
Connecting to the mains power supply
Before connecting, check that the nominal voltage of the appliance, that is, the
voltage stated on the rating plate, corresponds to the available supply voltage. The
rating plate is located on the lower casing of the hob.
WARNING
Shut off power to circuit before connecting wires to circuit.
The heating element voltage is AC 230 V~. The appliance also works perfectly on
networks with AC 220 V~ or AC 240 V~. The hob is to be connected to the mains
using a device that allows the appliance to be disconnected from the mains at all
poles with a contact opening width of at least 3 mm, eg. automatic line protecting
cut - out, earth leakage trips or fuse.
WARNING
The cable connections must be made in accordance with regulations and the
terminal screws tightened securely.
WARNING
Once the hob is connected to the mains supply, check that all cooking zones are
ready for use by briefly switching each on in turn at the maximum setting with
suitable cookware.
WARNING
Pay attention (conformity) to phase and neutral allocation of house connection and
appliance (connection schemes); otherwise, components can be damaged.
Warranty does not cover damage resulting from improper installation.
WARNING
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
8 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 8
2020-02-25
12:35:14
Installing into the countertop
1N~ (32A)
01
02
04
03
06
05
L
01
220-240 V ~
04
Blue
02
Brown
05
Gray
03
Black
06
Green/Yellow
NOTE
A
N
2N~ (16A): Separate the 2-phase wires
(L1 and L2) before connection.
01
05
07
06
04
L1
L2
N
01
220-240 V ~
05
Blue
02
380-415 V ~
06
Gray
03
Brown
07
Green/Yellow
04
Black
Installing the hob
02
03
Make a note of the serial number on the
appliance rating label prior to installation.
This number will be required in the case
of requests for service and is no longer
accessible after installation, as it is on the
original rating plate on the underside of the
appliance.
Serial number
A.
NOTE
01
04
02
05
03
06
L1
2 x 1N~ (16A): Separate the wires before
connection.
N1
07
L2
N2
01
220-240 V ~
05
Black
02
Brown
06
Gray
03
Blue
07
Green/Yellow
04
220-240 V ~
WARNING
For correct supply connection, follow the wiring diagram attached near the terminals.
Pay special attention to the minimum space and clearance requirements.
NOTE
The bottom of the hob is equipped with two fans. If there is a drawer under the
hob it should not be used to store small objects or paper, since they could damage
the fan or interfere with the cooling if they are sucked into it.
01
Min. 2 mm
02
560 mm
01
02
English 9
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 9
2020-02-25
12:35:14
Installing the hob
01
02
01
03
02
03
06
04
08
07
09
05
10
Installing the hob
x4
07
02
Ø6
03
90 °
04
11
04
12
06
Max. 50 mm, Min. 20 mm
01
08
Min. 60 mm
09
Min. 600 mm
750±1 mm
10
Min. 60 mm
05
490±1 mm
11
Min. 60 mm
06
R3
12
Min. 50 mm
01
05
08
07
Min. 40 mm
05
15 mm
02
520 mm
06
Min. 60 mm
03
Min. 40 mm
07
480 mm
04
25 mm
08
Min. 50 mm
10 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 10
2020-02-25
12:35:14
01
02
03
04
01
Min. 550 mm
02
Min. 35 mm
03
Min. 65 mm
04
Min. 100 mm
05
Min. 5 mm
05
Installing the hob
02
03
01
01
Min. 20 mm
02
Min. 2 mm
03
Min. 20 mm
Components
Induction hob
Bracket Spring
Screws
Magnetic Knob
English 11
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 11
2020-02-25
12:35:15
Before you start
Control panel
Cooking zones
01
06
01
06
09
01
06
04
01
06
01
03
08
04
Before you start
05
07
10
02
08
05
03
02
06
08
07
01
Induction rear Wide Flex zone 1800 W with Power Boost 2600 W
02
Induction front Wide Flex zone 1800 W with Power Boost 2600 W
03
Induction complete Wide Flex zone 3300 W with Power Boost 3600 W
04
Induction cooking zone 2200 W with Power Boost 3200 W
05
Induction cooking zone 1200 W with Power Boost 2000 W
06
Control panel
07
Lighting Bar
08
Virtual Flame Technology™
01
Cooking zone buttons
02
Magnetic knob (Power level setting)
03
Lock button
04
On/Off button
05
Timer buttons and display
06
Cooking zone display
07
Keep warm button
08
Pause button
09
Wide Flex zone button
10
Power Boost button
12 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 12
2020-02-25
12:35:15
Induction heating
The key features of your appliance
•
B
A
C
A.
B.
C.
Induction coil
Induced currents
Electronic circuits
•
•
•
•
•
•
•
•
•
•
Ceramic glass cooking surface: The appliance has a ceramic glass cooking
surface and four rapid - response cooking zones.
Touch buttons: Your appliance is operated using touch buttons.
Easy cleaning: One advantage of the ceramic glass cooking surface and The
detachable control knob is their accessibility. The smooth, flat surface is easy
to clean.
On/Off button: The On/Off button provides the appliance with a separate
mains switch. Touching this sensor switches the power supply on or off
completely.
Control and function indicators: Digital displays and indicator lights provide
information about settings and activated functions, as well as the presence of
residual heat in the various cooking zones.
Safety shutoff: A safety shutoff ensures that cooking zones switch off
automatically after a period of time if the setting has not been changed.
Power Boost : Use this function to heat up the contents of the pan faster
than maximum power level
. (The display will show
.)
Auto Pan-Detection: Each cooking zone incorporates an automatic pandetection system, the system is calibrated in order to recognize pans of a
diameter just slightly smaller than the cooking zone. Pans must always be
placed centrally on each cooking zone. And you should use suitable cookware.
Digital displays:
•
to
,
selected power level
•
residual heat (Stay Hot)
•
residual heat
•
the child lock is activated
•
message, the touch sensor button has been touched for longer than
8 seconds.
•
message, when the hob is overheated because of abnormal operation.
(example : operation with empty cookware)
•
message, cookware is unsuitable or too small or no cookware has
been placed on the cooking zone.
English 13
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 13
2020-02-25
12:35:15
Before you start
The Principle of Induction Heating:
When you place your cookware on a
cooking zone and you turn it on, the
electronic circuits in your induction
hob produce “induced currents” in the
bottom of the cookware which instantly
raise cookware’s temperature.
Greater speed in cooking and frying:
As the pan is heated directly and not
the glass, the efficiency is greater than
in other systems because no heat is
lost. Most of the energy absorbed is
transformed into heat.
Before you start
•
•
•
•
•
•
Keep warm
: Use this function to keep cooked food warm.
The display will show
.
Pause
: Use this fuction to switch all cooking zones on to the low power
setting. (example : to take a telephone call) The display will show
.
Wide Flex zone : Use this function to expand cooking zone into complete
left side. The Wide Flex zone is a large, rectangle-shaped area designed for
cooking multiple dishes.
Vritual Flame™: Get hassle free because inform you ‘Creating food now on the
cooktop’ by visually telling.
Magnetic knob: The power control is easy, simple and intuitive by using
magnectic knob.
Quick Stop: This option reduces the step and time it takes to stop cooking by
simple one touch.
Safety shutoff
If one of the cooking zones is not switched off or the heat setting is not adjusted
after an extended period of time, that particular cooking zone will automatically
switch itself off.
Any residual warmth will be indicated with
,
(for “hot”) in the digital
displays corresponding to the particular cooking zones.
The cooking zones switch themselves off at the following times.
Heat setting
Switch off
1-3
After 6 hours
4-6
After 5 hours
Before you start
7-9
After 4 hours
10-15
After 1.5 hours
NOTE
If the Hob is overheated because of abnormal operation,
And the Hob will be switched off.
will be displayed.
NOTE
If cookware is unsuitable or too small or no cookware has been placed on the
cooking zone,
will be displayed.
And after 1 minute the corresponding cooking zone will be switched off.
NOTE
Should one or more of the cooking zones switch off before the indicated time has
elapsed, see the section “FAQs and troubleshooting”.
Other reasons why a cooking zone will switch itself off
All cooking zones will switch themselves off if liquid boils over and lands on the
control panel.
The automatic shutoff will also be activated if you place a damp cloth on the
control panel. In both of these instances, the appliance will need to be switched
on again using the main On/Off
button after the liquid or the cloth has been
removed.
14 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 14
2020-02-25
12:35:16
Virtual flame technology
Residual heat indicator
Virtual flame technology creates the
appearance of flames when you turn on an
induction element.
When an individual cooking zone or the hob is turned off, the presence of residual
heat is shown with an
,
(for “hot”) in the digital display of the appropriate
cooking zones. Even after the cooking zone has been switched off, the residual
heat indicator goes out only after the cooking zone has cooled.
You can use the residual heat for thawing or keeping food warm.
WARNING
As long as the residual heat indicator is illuminated, there is a risk of burns.
•
•
•
WARNING
If the power supply is interrupted, the
,
symbol will go out and information
about residual heat will no longer be available.
However, it may still be possible to burn yourself. This can be avoided by always
taking care when near the hob.
Temperature detection
If for any reason the temperatures on any of the cooking zones were to exceed the
safety levels, should this happen then the cooking zone will automatically reduce
to a lower power level.
When you have finished using the hob, the cooling fan will continue to run until
the hob’s electronics has cooled down. And the cooling fan switched itself off
depending upon the temperature of the electronics.
English 15
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 15
2020-02-25
12:35:16
Before you start
•
Virtual flame technology is available only on the right burner.
As you turn the knob to adjust the power level, the color of the flames change.
(If you select Power Boost, the flames bounce off the cookware.)
The virtual flame may look different depending on the appearance, size, or
position of the cookware. (For the best results, use cookware that, matches the
element size. Cookware that is too large can cover the virtual flame. Cookware
that is too small can cause the virtual flame to be ill-formed.
Impurities on the cookware bottom or the cooktop surface can cause the
virtual flame to be ill-formed of incomplete. Clean up the cookware or the
cooktop surface before using them.
Before you start
Initial cleaning
Suitability test
Wipe the ceramic glass surface with a damp cloth and ceramic cooktop glass
cleaner.
Cookware is suitable for induction cooking,
if a magnet sticks to the bottom of the
cookware and cookware is labelled as
suitable by the cookware manufacturer.
WARNING
Do not use caustic or abrasive cleaners. The surface could be damaged.
Cookware for induction cooking zones
The induction hob can only be turned on when cookware with a magnetic base is
placed on one of the cooking zones. You can use the following suitable cookware.
NOTE
Cookware material
Can be suitability test using the Magnetic Knob.
Before you start
Cookware material
Suitable
Steel, Enamelled steel
Yes
Cast iron
Yes
Stainless steel
If appropriately labelled by the manufacturer
Aluminium, Copper, Brass
No
Glass, Ceramic, Porcelain
No
NOTE
Cookware for induction hob is labelled as suitable by the manufacturer.
NOTE
Certain cookware can make noise when being used on induction cooking zones.
These noise are not a fault in the appliance and do not affect operation in any way.
NOTE
Non-stainless containers are less in heat conductivity compared to stainless
containers, taking more time to cook.
NOTE
Induction cooking may not function properly on nonferrous cookware whose edge
doesn’t stick to the magnet, or on nonferrous cookware whose bottom is ironcoated.
Size of pans
Induction cooking zones adapt automatically to the size of the bottom of the
cookware up to a certain limit. However the magnetic part of the bottom of the
cookware must have a minimum diameter depending upon the size of the cooking
zone.
Diameter of cooking zones
Minimum diameter of the bottom of the cookware
220 mm
140 mm
160 mm
100 mm
Front or Rear Flex
140 mm
Complete Flex
240 mm (long side dimension), oval, fish kettle
16 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 16
2020-02-25
12:35:16
Operating noises
If you can hear.
•
Cracking noise: cookware is made of different materials.
•
Whistling: you use more than two cooking zones and the cookware. is made of
different materials.
•
Humming: you use high power levels.
•
Clicking: electric switching occurs.
•
Hissing, Buzzing: the fan operates.
The noise are normal and do not refer to any defects.
Using suitable cookware
NOTE
You can save valuable energy by observing
the following points.
•
Always position pots and pans before
switching on the cooking zone.
•
Dirty cooking zones and pan bases
increase power consumption.
•
When possible, position the lids
firmly on the pots and pans to cover
completely.
•
Switch the cooking zones off before
the end of the cooking time to use the
residual heat for keeping foods warm
or for thawing.
English 17
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 17
2020-02-25
12:35:17
Before you start
Better pans produce better results.
•
You can recognise good pans by their bases. The base should be as thick and
flat as possible.
•
When buying new pans, pay particular attention to the diameter of the base.
Manufacturers often give only the diameter of the upper rim.
•
Do not use pans which have damaged bases with rough edges or burrs.
Permanent scratching can occur if these pans are slid across the surface.
•
When cold, pan bases are normally bowed slightly inwards (concave). They
should never be bowed outwards (convex).
•
If you wish to use a special type of pan, for example, a pressure cooker, a
simmering pan, or a wok, please observe the manufacturer’s instructions.
Energy saving tips
Operation
Select cooking zone and power level setting
Using the touch buttons
To operate the touch buttons, touch the desired button with the tip of your pointed
finger until the relevant displays illuminate or go out, or until the desired function
is activated.
Ensure that you are touching only one button when operating the appliance. If
your finger is too flat on the button, an adjacent button may be actuated as well.
1.
For selecting the cooking zone, press
the corresponding cooking zone button.
2.
Turn the magnetic knob to set the
power level.
Switching the appliance on
The appliance is switched on using the On/
Off
button.
Press the On/Off
button for
approximately 1 second.
The digital displays will show
.
NOTE
NOTE
Operation
After the On/Off
button has been actuated to switch on your appliance, a
heat setting must be selected within approximately 20 seconds. Otherwise, the
appliance will switch itself off for safety reasons.
•
•
•
•
The default level is set to 15 when selecting the cooking zone.
If more than one button is pressed for longer than 8 seconds,
will show in
the heat setting display. To reset, press the On/Off
button.
If you try to turn the magnetic knob by grabbing the side or pushing it
strongly, it will not work.
If you try to turn the magnetic knob with gloves on, the knob may not work.
18 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 18
2020-02-25
12:35:17
Switching the appliance off
Using the child safety lock
To completely switch off the appliance, use
the On/Off
button.
Press and hold the On/Off
button for
1 second.
You can use the child safety lock to safeguard against unintentionally turning on a
cooking zone and activating the cooking surface. Also the control panel, with the
exception of the On/Off
button, can be locked in order to prevent the settings
from being changed unintentionally, for example, by wiping over the panel with a
cloth.
Switching the child safety lock On/Off
NOTE
1.
Press and hold the Lock
button for
approximately 3 seconds.
An acoustic signal will sound as
confirmation.
2.
Touch any button.
will appear in the displays,
indicating the child safety lock has
been activated.
For switching the child safety lock off,
press and hold the Lock
button for 3
seconds. An acoustic signal will sound
as confirmation.
After switching off a single cooking zone or the entire cooking surface, the
presence of residual heat will be indicated in the digital displays of the
corresponding cooking zones in the form of an
,
(for “hot”).
Quick stop
To switch off a cooking zone, press and hold
the cooking zone button for 2 seconds.
English 19
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 19
2020-02-25
12:35:18
Operation
3.
Operation
Timer
4.
Using the timer as a safety shutoff:
If a specific time is set for a cooking zone, the cooking zone will shut itself off once
this period of time has elapsed. This function can be used for multiple cooking
zones simultaneously.
Setting the safety shutoff
The cooking zone(s) for which you want to apply the safety shutoff must be
switched on.
1.
After switched on, press the
corresponding cooking zone button
to activate the flash signal for the
corresponding cooking zone display.
To cancel the timer settings, press the
target cooking zone button, and then
press and hold the Timer
botton for
2 seconds. This will cancel the cooking
zone’s timer settings with a beep. If
holding down the Timer
button for 2
seconds without selecting a burner, this
will cancel the timer settings of the last
changed burner.
To display the time remaining for any of the cooking zones, use the Timer
button.
The corresponding cooking zone display will begin to blink slowly.
The settings are reset using the Timer setting buttons ( or ). After the set
period of time has elapsed, the cooking zone automatically switches itself off, an
acoustic signal sounds as confirmation and the timer display indicates.
NOTE
Operation
2.
Press the Timer
button. The number
10 will be displayed above the timer
display.
If you press the Timer
button without selecting a cooking zone, the display
turns on but no timer settings is applied.
NOTE
To change the settings quicker, touch and hold any of the
desired value is reached.
3.
or
buttons until the
Press the Timer setting buttons
( or ) or turn the magnetic knob to
set the desired time. The safety shutoff
is now activated.
NOTE
The timer can be adjusted from 0 to 99.
20 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 20
2020-02-25
12:35:18
Using keep warm
Count up timer
For the count up timer to be used, the appliance must be switched on but all the
cooking zones must be not use timer as a safety shutoff.
1.
Press the Timer
button.
will appear in the timer display.
2.
The count up timer function becomes
active and the display numbers
increase over time. To cancel the timer
settings, press and hold the Timer
button for 2 seconds.
To stop the timer, press the Timer
button.
3.
Keep warm function keeps food at the proper temperature without over-cooking,
so it stays deliciously warm.
1.
Use this function to Keep cooked food
Warm. Press the corresponding cooking
zone button.
2.
Press the Keep warm
button.
Operation
English 21
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 21
2020-02-25
12:35:19
Operation
Power boost
Pause
The Power Boost
function makes additional power available to the each cooking
zones. (example : bring a large volume of water to the boil)
The Pause
function simultaneously switches all cooking zones that are
switched on to the low power setting and then back to the heat setting that was
previously set. This function can be used to briefly interrupt and then continue the
cooking process e.g. to take a telephone call.
When the Pause
function is activated, all buttons except for the Pause
, Lock
and the On/Off
buttons are disabled. To resume cooking, press the
Pause
button again.
Cooking zones
Max Boost time
220 mm
10 min
160 mm
10 min
Front or Rear Flex
10 min
Complete Flex
5 min
After these times, the cooking zones automatically return to power level
Control Panel
.
NOTE
In certain circumstances, the Power Boost function may be deactivated
automatically to protect the internal electronic components of the hob.
Operation
The cooking zones have a maximum power available to them.
If this power range is exceeded by switching on the Power Boost
function,
Power Management automatically reduced the heat setting of cooking zone.
B
A
A.
B.
Paired cooking zone
Paired cooking zone
Press the Pause
To Switch Off
Press the Pause
Return to previous power level
NOTE
Timer functions are not stopped by the Pause
Power management
A
To Switch On
Display
B
The display for this cooking zone alternates
for some seconds between the set heat
setting and the maximum possible heat
setting. After then, the display changes from
the set power level to maximum possible
power level.
button.
Flex control
The flex function can operate complete left side cooking zone for using large size
cookware. (example : oval cookware, fish kettle)
1.
Press the Wide Flex zone
button.
2.
Turn the magnetic knob to set the
power level. Power level display of
left side (front, rear) will be changed
together.
22 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 22
2020-02-25
12:35:20
Sound on/off
Suggested settings for cooking specific foods
1.
2.
3.
The figures in the table below are guidelines. The heat settings required for
various cooking methods depend on a number of variables, including the quality
of the cookware being used and the type and amount of food being cooked.
Press and hold the Pause
button
for 3 seconds within 10 seconds after
power on.
Sound will off and
will show in the
cooking zone display.
To change Sound setting, repeat No. 1
and No. 2 procedure.
Sound will on and
will show in the
Timer display.
Switch setting
Cooking method
Examples for Use
14-15
Warming
Sautéing
Frying
Warming large amounts of liquid, boiling
noodles, searing meat, browning goulash,
braising meat
10-13
Intensive
Frying
Steak, sirloin, hash browns, sausages,
pancakes / griddle cakes
8-9
Frying
Schnitzel / chops, liver, fish, rissoles, fried
eggs
6-7
Boiling
Cooking up to 1.5 l liquid, potatoes,
vegetables
3-5
Steaming
Stewing
Boiling
Steaming and stewing of small amounts of
vegetables, boiling rice and milk dishes
1-2
Melting
Melting butter, dissolving gelatine, melting
chocolate
NOTE
•
•
The heat settings indicated in the table above are provided only as guidelines
for your reference.
You will need to adjust the heat settings according to specific cookware and
foods.
NOTE
After power on, It is not possible to operate sound On/Off
later.
button 10 senconds
English 23
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 23
2020-02-25
12:35:20
Operation
4.
Press and hold the On/Off
button for
approximately 1 second to power on.
Maintaining your appliance
Hob
WARNING
Cleaning agents must not come into contact with a heated ceramic glass surface:
All cleaning agents must be removed with adequate amounts of clean water after
cleaning because they can have a caustic effect when the surface becomes hot.
Do not use any aggressive cleaners such as grill or oven sprays, scouring pads or
abrasive pan cleaners.
NOTE
Clean the ceramic glass surface after each use when it is still warm to the
touch. This will prevent spillage from becoming burnt onto the surface. Remove
scales, watermarks, fat drippings and metallic discolouration with the use of a
commercially available ceramic glass or stainless steel cleaner.
Stubborn soiling
1.
2.
3.
To remove food that has boiled over
and stubborn splashes, use a glass
scraper.
Place the glass scraper at an angle to
the ceramic glass surface.
Remove soiling by scraping with the
blade.
NOTE
Glass scrapers and ceramic glass cleaners
are available from specialty retailers.
Light soiling
1.
2.
Maintaining your appliance
3.
4.
Wipe the ceramic glass surface with a damp cloth.
Rub dry with a clean cloth. Remnants of cleaning agent must not be left on the
surface.
Thoroughly clean the entire ceramic glass cooking surface once a week with a
commercially available ceramic glass or stainless steel cleaner.
Wipe the ceramic glass surface using adequate amounts of clean water and
rub dry with a clean lint - free cloth.
24 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 24
2020-02-25
12:35:20
Problem dirt
Hob frame (option)
1.
Remove burnt-on sugar, melted plastic,
aluminium foil or other materials with
a glass scraper immediately and while
still hot.
WARNING
There is a risk of burning yourself when the
glass scraper is used on a hot cooking zone:
2. Clean the hob as normal when it has
cooled down. If the cooking zone on
which something has melted has been
allowed to cool, warm it up again for
cleaning.
NOTE
To avoid damaging your appliance
•
•
•
•
•
•
•
Do not use the hob as a work surface or for storage.
Do not operate a cooking zone if there is no pan on the hob or if the pan is
empty.
Ceramic glass is very tough and resistant to temperature shock, but it is
not unbreakable. It can be damaged by a particularly sharp or hard object
dropping onto the hob.
Do not place pans on the hob frame. Scratching and damage to the finish may
occur.
Avoid spilling acidic liquids, for example, vinegar, lemon juice and descaling
agents, onto the hob frame, since such liquids can cause dull spots.
If sugar or a preparation containing sugar comes into contact with a hot
cooking zone and melts, it should be cleaned off immediately with a kitchen
scraper while it is still hot. If allowed to cool, it may damage the surface when
removed.
Keep all items and materials that could melt, for example, plastics, aluminium
foil and oven foils, away from the ceramic glass surface. If something of this
nature melts onto the hob, it must be removed immediately with a scraper.
English 25
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 25
2020-02-25
12:35:21
Maintaining your appliance
Scratches or dark blemishes on the ceramic
glass surface, caused, for example, by a
pan with sharp edges, cannot be removed.
However, they do not impair the function of
the hob.
WARNING
Do not use vinegar, lemon juice or scale remover on the hob frame; otherwise dull
blemishes will appear.
1. Wipe the frame with a damp cloth.
2. Moisten dried debris with a wet cloth. Wipe and rub dry.
Warranty and service
FAQs and troubleshooting
Information code
A fault may result from a minor information that you can correct yourself with
the help of the following instructions. Do not attempt any further repairs if the
following instructions do not help in each specific case.
WARNING
Repairs to the appliance are to be performed only by a qualified service technician.
Improperly effected repairs may result in considerable risk to the user. If your
appliance needs repair, please contact your customer service centre.
Problem
What should I do if the
cooking zones are not
functioning?
What should I do if the
cooking zones will not
switch on?
Possible cause
•
•
•
•
Warranty and service
What should I do if the
display except for
,
the residual warmth
indicator suddenly
disppears?
•
What should I do if,
after the cooking zones
have been switched off,
residual warmth is not
indicated in the display.
•
•
Check the Auto Cook sensor.
C1
The temperature is sensed
higher than specified.
•
The On/Off
button
was accidentally
actuated.
The control panel is
partially covered by a
damp cloth or liquid.
•
The On/Off
button
was accidentally
actuated.
The control panel is
partially covered by a
damp cloth or liquid.
•
The cooking zone
was only briefly used
and therefore did not
become hot enough.
•
•
•
•
If the fuses trip a
number of times, call an
authorised electrician.
The appliance is
properly switched on.
The appliance is
properly switched on.
Clean the control panel.
The appliance is
properly switched on.
Clean the control panel.
Solution
Restart the appliance using
the On/Off
button. If
the problem continues,
disconnect power for more
than 30 seconds. Then,
restart the appliance and try
again. If the problem still
continues, contact a local
service center.
C2
Check the Auto Cook sensor.
A2
The DC Motor fails to operate
because of problems with the
PCB or wiring, or electrical
disturbance on the motor blade.
d0
The sensor is pressed for more
than 8 seconds.
Check if the sensor pad
is wet or pressed. If the
problem continues, restart
the appliance using the On/
Off
button. If the problem
still continues, contact a
local service center.
F0
Communications between main
and sub PCBs fail.
F2
The touch-enabled IC
communicates abnormally.
Restart the appliance using
the On/Off
button. If
the problem continues,
disconnect power for more
than 30 seconds. Then,
restart the appliance. If the
problem still continues,
contact a local service
center.
Solution
The fuse in the house
wiring is intact.
The control indicators
in the control panel are
illuminated.
Possible cause
C0
If the cooking zone
is hot, please call the
customer service center.
26 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 26
2020-02-25
12:35:21
What should I do if the cooking zone will not switch on or off?
This could be due to one of the following possibilities:
•
The control panel is partially covered by a damp cloth or liquid.
•
The child safety lock is on.
What should I do if the
display is illuminated?
Check for the following:
•
The control panel is partially covered by a damp cloth or liquid.
To reset, press the On/Off
button.
•
If liquid has overflowd on control panel, please wipe the liquid.
What should I do if the
display is illuminated?
Service
Before calling for assistance or service, please check the section “FAQs and
troubleshooting”.
If you still need help, follow the instructions below.
Is it a technical fault?
If so, please contact your customer service centre.
Always prepare in advance for the discussion. This will ease the process of
diagnosing the problem and also make it easier to decide if a customer service
visit is necessary.
Please take note of the following information.
Check for the following:
•
The hob is overheated because of abnormal operation.
•
After hob is cooled down, press the On/Off
button for resetting.
•
•
What should I do if the
When calling, please know the model and serial number of your appliance. This
information is provided on the rating plate as follows:
display is illuminated?
Check for the following:
•
Cookware is unsuitable or too small or no cookware has been placed on the
cooking zone.
•
If you use suitable cookware, displayed message will automatically disapear.
What should I do if the cooling fan runs after the hob is turned off?
Model description
S/N code (15 digits)
We recommend that you record the information here for easy reference.
•
•
Model:
Serial number:
When do you incur costs even during the warranty period?
•
•
If you could have remedied the problem yourself by applying one of the
solutions provided in the section “FAQs and troubleshooting”.
If the customer service technician has to make several service calls because he
was not provided with all of the relevant information before his visit and as a
result, for example, has to make additional trips for parts. Preparing for your
phone call as described above will save you the cost of these trips.
English 27
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 27
2020-02-25
12:35:21
Warranty and service
Check for the following:
•
When you have finished using the hob, the cooling fan runs by itself for
cooling down.
•
After the hob’s electronics has cooled down, the cooling fan will be turned off.
•
If you request a service call because of an information made in operating the
appliance, the visit from the customer service technician may incur a charge
even during the warranty period.
•
•
What form does the problem take?
Under what circumstances does the problem occur?
Technical data
Product information
Technical data
800 mm
Depth
520 mm
Height
56 mm
Width
750 mm
Heating technology
Depth
490 mm
Corner radius
3 mm
Number of cooking zones and/or
areas
Appliance dimensions
Worktop cut - out
dimensions
Model identification
Type of hob
For circular cooking zones or area:
diameter of useful surface area per
electric heated cooking zone (Ø)
220-240 V ~ 50 / 60 Hz
Connection voltage
7.0 kW
Maximum connected load power
Weight
Supplier’s name
Width
Net
16.5 kg
Gross
19.5 kg
For non-circular cooking zones or
areas: length and width of useful
surface area per electric heated
cooking zone or area (L x W)
Energy consumption per cooking
zone or area calculated per kg
(EC electric cooking)
Cooking zones
Technical data
Position
Diameter
Power
Front right
160 mm
1200 W / Boost 2000 W
Center
220 mm
2200 W / Boost 3200 W
Front Flex
-
1800 W / Boost 2600 W
Rear Flex
-
1800 W / Boost 2600 W
Complete Flex
-
3300 W / Boost 3600 W
Energy consumption for the hob
calculated per kg (EC electric hob)
Samsung Electronics co. Ltd.
NZ84T9770EK
Built-In
Induction cooking zones and cooking area
3
16.0 cm, 22.0 cm
43.5 x 22.5 cm
Ø 16.0 cm : 193.0 Wh/kg
Ø 22.0 cm : 176.5 Wh/kg
43.5 x 22.5 cm : 195.6 Wh/kg
188.4 Wh/kg
* Data determined according to standard EN 60350-2 and Commission Regulations
(EU) No 66/2014.
Energy saving tips
•
•
•
Always position pots and pans before switching on the cooking zone.
Dirty cooking zones and pan bases increase power consumption.
Using a pressure cooker reduces cooking time.
28 English
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 28
2020-02-25
12:35:21
Memo
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 29
2020-02-25
12:35:21
Memo
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 30
2020-02-25
12:35:21
Memo
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 31
2020-02-25
12:35:21
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
AUSTRIA
0800 72 67 864 (0800-SAMSUNG)
www.samsung.com/at/support
BELGIUM
02-201-24-18
www.samsung.com/be/support (Dutch)
www.samsung.com/be_fr/support (French)
DENMARK
707 019 70
www.samsung.com/dk/support
FINLAND
030-6227 515
www.samsung.com/fi/support
FRANCE
01 48 63 00 00
www.samsung.com/fr/support
GERMANY
06196 77 555 77
www.samsung.com/de/support
ITALIA
800-SAMSUNG (800.7267864)
www.samsung.com/it/support
CYPRUS
8009 4000 only from landline, toll free
www.samsung.com/gr/support
GREECE
80111-SAMSUNG (80111 726 7864) only from land line
(+30) 210 6897691 from mobile and land line
www.samsung.com/gr/support
LUXEMBURG
261 03 710
www.samsung.com/be_fr/support
NETHERLANDS
088 90 90 100
www.samsung.com/nl/support
NORWAY
21629099
www.samsung.com/no/support
PORTUGAL
808 207 267
www.samsung.com/pt/support
SPAIN
91 175 00 15
www.samsung.com/es/support
SWEDEN
0771 726 786
www.samsung.com/se/support
SWITZERLAND
0800 726 786
www.samsung.com/ch/support (German)
www.samsung.com/ch_fr/support (French)
UK
0333 000 0333
www.samsung.com/uk/support
IRELAND (EIRE)
0818 717100
www.samsung.com/ie/support
DG68-00630B-00
NZ84T9770EK_EU_DG68-00630B-00_EN.indd 32
2020-02-25
12:35:21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement