TP-Link CAP300 300Mbps Wireless N Ceiling Mount Access Point Installation Guide

Add to my manuals
2 Pages

advertisement

TP-Link CAP300 300Mbps Wireless N Ceiling Mount Access Point Installation Guide | Manualzz
ETHERNET
The port is used to connect to a router or a switch to transmit data or to a PSE (Power Sourcing Equipment),
Option 1: Ceiling Rail Mounting (Only for CAP1200/CAP1750)
such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cabling.
POWER
The port is used to connect the CAP to a power socket via the provided power adapter.
Quick Installation Guide
Wireless Ceiling Mount Access Point
CAP300/CAP1200/CAP1750
Kensington
Ceiling T-rail Clip
The kensington lock port is used to connect to a kensington lock to secure your CAPs.
1
Typical Network Topology (FIT mode)
1
Position the Ceiling T-rail Clip and push
the movable part toward the rail base.
Internet
LED Indication
M3×6 Pan-head Screws (Qty.5)
Router
2
Use an M3×6 pan-head screw to secure
the T-rail Clip onto the ceiling rail.
Wireless Controller
Solid Green
Switch
Flashing Yellow
Firmware update is in progress. Do not
disconnect or power off the device.
The device is working properly or the
connection between the device and the
wireless controller is established.
PC
CAP
CAP
Double-flashing Red, Green, Yellow
The device is being reset to its
factory default settings.
Flashing Red
System errors. RAM, Flash, Ethernet,
WLAN or firmware may be
malfunctioning.
CAP
3
Attach the mounting bracket to the
Ceiling T-rail Clip using four M3x6
pan-head screws.
Flashing Green (FIT mode only)
The device is not connected to a wireless
controller.
Interface Panel
FIT FAT
RESET
Clients
ETHERNET
POWER
FIT FAT
The FIT/FAT switch is used to toggle the AP’s working mode. The toggling of the mode will reboot the AP.
In FIT mode, APs can be centrally managed by TP-Link’s wireless controller. The default FIT mode is used
The wireless controller can be in the same or different network segment as the CAPs.
2
Hardware Installation
The CAP can be ceiling rail mounted, ceiling-mounted, or wall-mounted.
when you want to deploy a large wireless network.
Note: Please take the power supply into consideration before the installation.
wireless network. The AP cannot be managed by wireless controller in FAT mode.
Option 1: Ceiling Rail Mounting (for CAP1200/CAP1750)
In FAT mode, you can log in to AP’s webpage to manage the AP alone. The FAT mode is used in a small
RESET
With the device powered on, press and hold the button for about 8 seconds until the LED flashes red, then
release the button. The device will restore to factory default settings.
Option 2: Ceiling Mounting
Option 3: Wall Mounting
4
Attach the CAP to the mounting bracket
by aligning the arrow mark on the CAP
with the arrow mark on the mounting
bracket, then rotate the CAP until it locks
into place, as shown on the left.
5
Connect the Ethernet cable to the
ETHERNET port.
Option 3: Wall Mounting
Option 2: Ceiling Mounting
Note: We recommend that you install the CAP with the Ethernet port downward.
3
Power Supply
The CAP can be powered via a PSE device (such as a PoE switch) or a power adapter.
Via PoE Switch
Washers (Qty.3)
M3×30 Pan-head Screws (Qty.3)
Wing Nuts (Qty.3)
M3×28 Plastic Wall Anchors (Qty.3)
Attach the CAP to the mounting bracket by
aligning the arrow mark on the CAP
with the arrow mark on the mounting
bracket, then rotate the EAP until it locks
into place, as shown on the left.
Remove the ceiling tile.
Hole for Ethernet cable
FIT FAT
RESET
ETHERNET
POWER
PoE Switch
Via Power Adapter
2
Place the mounting bracket in the center of
the ceiling tile. Mark three positions for the
screw holes and a position for the Ethernet
cable hole.
Drill three 4mm holes for the screws and a
25mm hole for the Ethernet cable at the
marked positions.
Connect an Ethernet cable from the PoE switch to the ETHERNET port.
1
1
X3
M3×20 Self-tapping Screws (Qty.3)
2
98.6mm
Plug one end of the provided power adapter into the POWER port of the CAP and the
other end to a standard electrical wall outlet.
Make two small pencil marks on the wall.
Make sure the two marks are level and
98.6mm apart.
Drill a 6mm hole through the center of
each mark.
Power Adapter
FIT FAT
RESET
ETHERNET
POWER
Switch
3
Secure the mounting bracket to the ceiling
tile using three M3x30 pan-head screws,
washers and wing nuts, as shown on the
left.
3
Insert the plastic wall anchors into the
6mm holes and drive the self-tapping
screws into the anchors. Do not drive the
screws all the way in and leave enough
clearance to hang the CAP.
4
Software Configurations
In FIT Mode
In FIT mode, CAP should be managed by the wireless controller. Please refer to the
Wireless Controller User Guide to learn more information about configuring and using
the controller.
Note: The IP address of the wireless controller must be reachable for the CAPs in the network.
In FAT Mode
1 Launch a web broswer and enter 192.168.0.254 in the address bar.
4
Attach the CAP to the mounting bracket by
aligning the arrow mark on the CAP with
the arrow mark on the mounting bracket,
then rotate the CAP until it locks into place,
as shown on the left.
5
Feed the Ethernet cable through the hole
and set the ceiling tile back into place.
Connect the Ethernet cable to the
ETHERNET port.
4
Hang the CAP on the screws. Make sure
the CAP is firmly seated against the wall.
Note: To log in to the device, the IP address of your PC should be set in the same subnet
addresses of the device. The IP address is 192.168.0.x (”x” is any number from 1 to 253). Subnet
Mask is 255.255.255.0.
2 Create a new username and password for login, and then click OK.
3 The webpage will be shown. Click the menu bar to configure the coresponding parameters.
For detailed configuration, please refer to the User Guide. You can download it from
http://www.tp-link.com/en/support in the download center.
5
Connect the Ethernet cable to the
ETHERNET port on the CAP.
For technical support, User Guide and other information, please
visit http://www.tp-link.com/support, or simply scan the QR code.
The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU
General Public License (“GPL”). As applicable, the terms of the GPL and any information on obtaining access to the respective GPL
Code used in TP-Link products are available to you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/). The
respective programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more authors. For
details, see the GPL Code and other terms of the GPL.
©2017 TP-Link 7106507912 REV1.0.2

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement