Yale Smart Home Alarms Manual

Conexis L1
Yale Smart Home
Alarm Manual•
SR-310 • SR-320 • SR-330 • SR-340
An ASSA ABLOY Group brand
The smarter way to protect your home•
smart
Living
Control your home
security from your
smartphone
2
The smarter way to protect your home•
Introduction
Contents
1. Location planning
4
2. Un-pack & power devices
6
3. Initial set-up
10
4. Mounting devices
13
5. Using the system
18
6. Default settings
21
7. Adding & using devices
22
8. Changing batteries
26
9. Troubleshooting
31
10. Specifications 33
For more information on this product and
Yale Smart Living Range visit
www.yale.co.uk/smart-living
Consumer Support:
www.yale.co.uk/help
2
The 2 year guarantee for this
product is active from the
date of purchase (A copy of
this guarantee is available on
our website).
3
Introduction
Location
Planning•
(GB) Step by step index (03)
Introduction
(GB) Step by step index -
1
(12)
Plan device locations and check devices
range
(GB)before
Installation
(IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation 1 -mounting.
Accessories vary depending on kit
(DK) Installation.
7
Key Pad
2
1
mart Home Alarm kit. This simple to install system has
30m Operating Range
nd.
Smoke Detector
b
Powe
the Yale
Smart Home Alarm kit. This simple to install (GB)
system
Step byhas
step index Introduction
eained
user
andin
no mind.
connections are needed between the
the home decor, lift carpets or run cables.
1
3
2 needed between the
6 PIRcontained
Cameras) in this and
system. no
As well
as extra
eMax.self
connections
are
moke detectors, you can add keyfob remote controls
o Smart
damage
home
decor,
carpets
orhas
run cables.
le
Homethe
Alarm
kit. This
simplelift
to install
system
nvenience.
All devices must be within 30 metres of the Smart Hub and
must not be mounted on or near large metal objects. Avoid
obvious sources of electrical interference such as fridges and
microwave ovens.
External Siren
arn
tery Le
Bat Off>
n
r <O
• The Key Pad should be
accessible from a protected
entry/exit point
• Ensure that the Key Pad is
not visible from the outside of
the premises.
LAN
Mount on a ceiling in main
access areas e.g. hallways, top
of stairs.
n
er
Pow
2
d
b
ar
ry Le
BantteOff>
<O
LAN
n mind.
(p. 07)
Key Fob
• Use inside or outside within a
30m range
30M
a
30M
30M
ar
ery Le
BanttOff>
<O
• Mount as high as possible on
the door or window frame.
a
0 devices (Max. 6 PIR Cameras) in this system.
As well as extra
the
PIRs and smoke detectors, you can add keyfob remote controls
control convenience.
2
ces (Max. 6 PIR Cameras) in this system. As well as extra
er
Pow
LAN
Accessories
(p. 04-06) Door/Window
Contact vary depending o
Ø 3.5mm
e mains supply or seek the services of a qualified
wered by an adaptor and all other components are
4
3
ontainedBatteries
and no
are or
needed
included).
willconnections
operate for 2 years
more between
Ø 5mm
ar testing
battery
changes
(when notified
bycables.
the
age
the and
home
decor,
lift carpets
or run
peace of mind.
n
Mount as high as possible, out of
easy reach.
(p.
30M
c
nal siren are ‘tamper’ protected. Any unauthorised
nd
youincan
add keyfob remote controls
the smoke
system isdetectors,
armed will result
an alarm.
6
wire
into the mains supply or 5seek the
services
l convenience.
4
(p. 08)
of a qualified
HUB is powered by an adaptor and all other components are
l batteries included). Batteries will operate for
years
or index
more
(GB)2Step
by step
3 by the
ging. Regular testing and battery changes (when notified
1
egular
testing
andwho
battery
changes (when notified by the
ability
and
peace
of mind.
e used with
persons
have
consented to being
5
1
Smart Hub 2.0
(03)
sing ladders or steps, please follow manufacturer’s
hand and power tools and follow the
manufacturer’s
(GB)
by step
index ocare
the
supply
or used.
seek
theStep
services
thatmains
the correct
tools are
Wear
goggles
or of a qualified
anisadaptor
all other
components are
d.powered
The externalby
Siren
extremely and
loud, please
ensure
o a safe
distance before
testing.will operate for 2 years or more
ries
included).
Batteries
nd peace
tem
is not toof
bemind.
used to make 999 emergency calls
bility for any actions taken by emergency services for
.ystem
xternal has
siren are ‘tamper’ protected. Any
3
e controls
(p
n
Lear
LAN
The Panic Button can activate your alarm
immediately - even when the system is
disarmed.
• Keep out of reach of children
• Keep hidden from view, but easily
accessible.
Information and illustrations are subject to change within this
document. Yale reserves the right to alter the specification and
product design at anytime without notice. Yale® is a registered
trademark. © 2018 ASSA ABLOY. All rights reserved.
ry
BantteOff>
<O
30M
Accessories vary
on kit
(p. depending
09-10)
Accessories vary depen
Panic Button
and external siren are ‘tamper’unauthorised
protected.
Any unauthorised
PIR Motion Detector
kit.the
This
simple
to
install
system
hen
system
armed
will result
in anhas
alarm.
(p. 11)
ems
when
system
iswith
armed
will result in an alarm.
his alarm
system the
isisNOT
compatible
HSA6000
ries. Please note the prefix “EF- & SR-” on the front of
6
4
atibility.
n using ladders or steps, please follow manufacturer’s
tween
the
on
using
or steps,
please follow manufacturer’s
singwhen
hand and
powerladders
tools and follow
the manufacturer’s
nnections
arehand
needed
between
the
when
using
and
power
tools
follow
Take
care
that the
correct
tools
are used.
Wearand
goggles
or the manufacturer’s
ift
carpets
or
run
cables.
uired.
external
is extremely
loud,tools
please are
ensure
them.The
Take
careSiren
that
the correct
used. Wear goggles or
2
4
7
eat
to aextra
safe distance before testing.
ll as
ere
required. The external Siren is extremely 2
loud, please ensure
ras) in this system. As well as extra
er
Pow
• Ensure the Smart Hub is hidden
from view.
• Access to a mains socket and
broadband internet router is
required.
n
• Mount 1.8m - 2.1m above floor level
• Location in a corner will ensure wider room coverage
• Do not mount the PIR where its field of view will be
obstructed
• Do not point directly at sources of heat e.g. fires or
boilers, and do not position directly above radiators
• Avoid mounting the PIR directly facing a window
• Do not point the PIR at a door protected by a Door/
Window Contact
er
Pow
LAN
y Learn
Batter
Off>
<On
er
Pow
LAN
4
ar
ry Le
BantteOff>
<O
Pet PIR Motion Detector
(p
(p. 22-24)
• Suitable for homes with pets up to 25kg
• For rooms where pets are active and may climb on furniture, protect the area with a Door/Window contact instead to prevent false alarms.
(p. 04-06)
(p. 11)
5
(p.
Unpacking the devices•
r
Powe
Smart Hub 2.0
ar
ry Le
BantteOff>
<O
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE
(DK) Installation.
n
LAN
Key Pad
Remove battery strips (1
1. Plug in the power adaptor and connect the Smart Hub to your internet router using the cable provided.
2
3
Router
NOT INCLUDED
Panic button A
Yale
1
2
7
8
4
Away
/
5
3
6
9
Panic button B
LED
Learn button=
Press 8 and 9 together
(GB) Installation - (IT) Installazione - (DE)0 Installation - (NO) Installasjon - (SE) Insta
(DK) Installation.
Disarm
Part
Arm
HomeArm
4
Test your planned location of components (2
a
er
Pow
ery
BanttOff>
<O
Le
arn
tery
Bant Off>
<O
<On Off>
b
L AN
See page 16 for Key pad installation.
PIR
Remove battery strips (1
Yale
Press button to test connection (3
Status
LED
Alarm Hub Status
Top Light:
Shows server
connection status
Learn/Test button
HOME SERVER
Fault- -See
See
Fault
troubleshooting
shooting
trouble
(page31)
22)or
or
(page
checkapp
app
check
fornotifications
notifications
for
Middle Light:
Shows fault status
Cover
screw
(GB) Installation - (IT) Installazione - (DE) Installation - (
(DK) Installation.
Door/Window Contact
8 9
Remove battery strips (1
Test your planned location of components (2
OK
Bottom Light:
Shows arming status
Solid Red Fully Armed
Flashing Red Part Armed
White Armed
Disarmed
6
Sensor
Magnet
Yale
LED
Learn/Test
button
Gap no more
than 10mm
6
Press button to test connection
Test(3your planned location of components (2
7
b
a
3 x 1.5v AA
Unpacking the devices•
External Siren
c
(Lithium)
Ø 5mm
7
1.2
1
The Siren is very loud! Take care not to activate
the Siren tamper switch unnecessarily.
SR-PVC
(21)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation (DK) Installation.
WARNING
3 x 1.5v AA
(Lithium)
d
a
2.4
5
a
Key Fob SR-PVC
6
1.
3 x 1.5v AA
(Lithium)
2.
3.
b
b
CR 2032
CR
2032
SR-PVC
3
CR 2032
(11)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation (DK) Installation.
b
PIR Image Camera
5
d
c
Ø 5mm
SR-KF
a
Remove battery strips (1
Smoke
SR-KF Detector
3 x 1.5v AA
Learn/Test button
3 x 1.5v AA
SR-KF
4
5
a
Flash light
6
SR-SD
b
3 x 1.5v AA
Camera
(11)
Learn: Hold for 10 seconds
Test: Hold for 1 second
your
planned location
of components
- (IT) Installazione Test
- (DE)
Installation
- (NO) Installasjon
- (SE)(2Installation -
PIR Video Camera
5
Remove battery strips (1
SR-SD
CR 2032
Panic Button
CR 2032
SR-SD
Flash light
Press button to test connection (3
SR-PB
CR 2032
Camera
Learn/Test button
d location of components (2
SR-PB
Learn: Hold for 10 seconds
Test: Hold for 1 second
Power Switch
Plug in to mains socket.
SR-PB
8 9
ess button to test connection (3
On/Off, Test &
Learn button
8
6
Learn: Hold for 10 seconds
Power On/Off: Press & release
Test: Press & release
9
Download the app•
Setting up devices•
Adding new devices (Optional: Use it only if you have extra devices outside the kit)
(08)
(GB) App download - (IT) Scarica l'App Please ensure all devices
powered
and
operational
at- this point.
(DE) Appare
Download
- (NO) Nedlasting
av App
- (SE) Installera appen
3
(08)
All devices in the kit are linked to the Smart Hub. If you want to add more devices, you can do this by using the “Add new device”
section in the Smart Living Home app.
(DK) Installer APP.
(GB) App download - (IT) Scarica l'App Download
the -Yale
Yale
Home
App
Living
Home
(DE) App Download
(NO) Smart
Nedlasting
av App
- (SE) Installera appen (DK) Installer APP.
3
Internet Connection: Required on
Go to the app menu
Select Add Device, then activate leaning mode.
iOS 9 +
Yale Smart Living Home
Android 4.2 +
IOS 9.0 +
1
Android 4.2 +
First time registration
IOS 9.0 +
Enter Learn Mode
Follow the set-up instructions in the app.
2
Android 4.2 +
Learn in Devices
Press the learn button on the device you leant to add then see diagrams below. The Smart Hub will beep (single or multiple
dependent on device) when a new device is registered. You will then see your new device in your device List within the home app.
Learn/ Test
button
Press & hold
for 3 seconds
Serial No.
Learn/Test
button
One single
press.
Learn/Test
button
One single
press.
Learn/Test
button
One single
press.
EF-PETPIR
Learn/Test button
One single press.
Serial No.
Learn/Test
button
Press 8 and 9
together
Ensure you
initialise your
keypad before
you learn it in.
(See page 17)
Please Note:
Panel Serial NumberSerial
can beNo.
found on the Smart Hub sticker.
LED
Learn/Test button
One single press.
For
please
holdhold
thethe
Learn
button
forfor
1010
seconds,
to enter
enter Learn
Learnmode.
mode.
Forthe
thefollowing
followingdevices,
accessories,
please
Learn
button
seconds,before
beforereleasing
releasing to
If the device doesn’t learn in, remove the batteries for 5 seconds, then replace and
Learn/Test button
Hold for 10 seconds try relearning within 3 minutes.
Please register the hub within one hour of power up, otherwise app ‘authentication error’ will appear
– re-boot the hub (including switching off / on the back-up battery) and start the process again if
necessary.
Recording your set-up information
SR-PVC must be learned in with the
tamper screw removed so that the tamper
is open. Sensor will not learn with tamper
closed.
E-mail used to set up system:
SR-PC
Smart Security Hub 2.0 serial number
Phone number used for notifications:
Key Pad PIN Code for Disarm/Arm (default
1234):
3
SR-PVC Learn/Test button
Hold for 10 seconds
SR-PS Learn/Test button
Hold for 10 seconds
Exit Learn Mode:
Press Stop learning mode on the app
Key Pad code for key Pad setting (default 0000):
10
11
(09)
(GB) Setting up - (IT) Configurazione - (DE) Einstellung (NO) Tilkobling og montering av alarmsentralen - (SE) Driftsättning (DK) Opsætning.
Range Test•
Mounting Devices•
4
1
Check Devices Range
PIR Motion Detector
b
2
1
1.) Place each device in the location where you wish to mount them.
er
Pow
ar
ry Le
Bantte
Off>
<O
n
LAN
Before mounting each device please check the system with a simple range test.
a
Login to your Yale Home App. Go to app menu, select Settings > Alarm Settings > Tests then press the ‘Start Walk Test’
button.
2
3
a
3
b
Hold the devices in the desired location and press the Test/LearnRouter
button on the devices. (see page 11)
NOT INCLUDED
~1.8m
2.1m
If the sensor signal reached the Smart Hub, it will show in the device list on your app.
Ø 3.5mm
4
d
a
b
Ø 5mm
c
4
5
6
a
When you are happy that all your rndevices can communicate <On
with the
Smart Hub, please proceed to mounting the devices.
Off>
er
Pow
b
tery
Bant Off>
ea
tery L
Batn Off>
<O
O
Before you mount a device
use the device <settings
in the Smart Living Home app to bypass the device and disable the
LAN
tamper alert. After the device is fully in place don’t forget to disable the bypass.
Key Pad
Smart Hub 2.0 Mounting
2
b
b
3
<OBatte
n Of ry
f>
Lear
n
OR
a
Powe
r
a
1
N
a
LA
Ø 3.5mm
d
4
b
c
b
Ø5mm
a
Ø 5mm
c
5
6
The Smart Hub can be free standing, either vertically or horizontally on a flat surface with access to mains socket and
broadband internet router.
It is also suitable for wall mounting. Using the two holes on the mounting back plate, mark the position of the holes. Drill
two holes and fix with the screws and plugs provided. Hook the Smart Hub onto the plate.
12
13
Mounting Devices•
Mounting Devices•
Door/Window Contact
PIR Camera
(14)
b
2
1
c
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation (DK) Installation.
7
1
2
a
a
3
1. The sensor should be on the frame while the magnet should be on the door/window.
Testing
The gap between the magnet and sensor should
be no more than 10mm when closed. Test to see
whether the magnet is in range of the sensor: before
mounting hold the magnet and sensor in place and
then pull them apart. If the sensor LED lights up it
implies the two items are within range.
3
a
b
4
Ø 3.5 mm
b
~1.8m
2.1m
Ø 3.5mm
max 10mm
5
Clean the mounting surface with a suitable degreaser agent and mount using the adhesive pads.
Clean the mounting surface with a suitable degreaser agent and mount using the adhesive pads
Please note that some surfaces may be unsuitable for mounting using the adhesive pads. Please use
Please
note that some surfaces may be unsuitable for mounting using the adhesive pads. Please use
screw mounting in these cases.
screwmounting in these cases.
or
4
b
5
d
a
or
c
Ø 5 mm
6
7
5
b
6
6
b
7
a
b
a
a
14
15
1
Mounting Devices•
Mounting Devices•
Mounting the External Siren
(21)
(21)Installation (GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation (DK)
Installation.
The tamper spring
is Installation.
fully compressed when the siren is mounted. If there is a gap, pack with a
(DK)
(21)
7
suitable
spacing
material.
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
1
(DK) Installation.
1
1.2
1
2
a
b
(IT) Associazione/test - (DE) Verbinden/Testen (NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
7
2.
1.1
a
Powering up the siren
2 will
b
automatically disable the siren
tamper for a three hour period.
b
7
Pair / Test button
Panic Button
a
3
3
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation (DK) Installation.
Ø 5mm
2.
b
a
b
3
a
d
d
c
c
Ø 5mm
Ø 5mm
4
b
5
a
b
4
6
a
5
a
6
d
b
Ø 5mm
23.
1
c
Smoke Detector
Pair (GB)
/ Test
button
Installation
- (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(15)
(DK) Installation.
(IT) Associazione/test - (DE) Verbinden/Testen (NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
3
3.4
4.5
a
7
2
1
6
Pair / Test button
b
(IT) Associazione/test - (DE) Verbinden/Testen (NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
3
16
1
1
17
Using the System•
Using the System•
Arming and Disarming your Alarm
Configuring Device Behaviour
Using the Yale Home App
Go to the app menu, select Settings > Alarm Settings > Devices to access your device list. Go in to the settings for
each device and select the required setting.
Swipe
Swipe down to
part arm
Swipe down to
fully arm
Changing your Key Pad PIN
The Key Pad PIN is the PIN you set during the alarms first installation. You can set up to 10 sets of 4 digit PIN numbers in the app.
Setting up Part Armed Mode
Part Armed mode is usually used to protect the ground floor when you are upstairs in bed.
Disarmed
Part-Armed
Armed
Burglar
Go to the app menu, select Settings > Alarm Settings > KeyPad PIN Code Settings and select the user you want to edit the PIN
Key
code for or add another PIN.
Disarmed
Burglar
Burglar
Burglar
Home Omit
Home Omit
Disarmed
Part-Armed
Armed
Disarmed
Home
Access
Burglar
Part-Armed
Armed
Sensor
Part-Armed Ignored Armed
Home Omit
Home Omit
Home Access
Home Omit
Home Access
Entry
Instant Siren
Home access
Entry
Entry
Home Access
Entry
Triggers
Countdown
Entry
18
19
Using the System•
Adding Alert Notifications
You can add/delete email addresses that will be alerted when the alarm is triggered. You can choose to have
ALL events (or Burglar only) reported via email.
Hint: our report email will use the email address of: [email protected] Save this email address
as your VIP (Apple iOS) or Priority (Android) email and assign a special ringtone to it.
You can also add SMS alerts to specified mobile numbers (burglar events only)
Go to the app menu, select Settings > Users > Notification Settings to manage your notifications.
Default Settings•
Disarmed
All devices (except SR-PC and SRPVC) are pre-set to “entry” mode.
When the system is first armed, users will have 30
seconds to exit the building. If the system is already
armed, triggering any sensors will cause an entry
countdown to begin.
SR-PC/SR-PVC’s default setting is “Burglar only”, i.e.
immediate triggering during full arm and sleep during
Part Arm. This is done to conserve battery life.
You can change the entry/exit delay timing and other
settings for both fully armed and part armed mode.
Part-Armed
Burglar
Key
Disarmed
Burglar
Burglar
Burglar
Home Omit
Home Omit
Disarmed
Armed
Part-Armed
Disarmed
Home
Access
Burglar
Part-Armed
Armed
Sensor
Part-ArmedIgnoredArmed
Home Omit
Home Omit
Home Access
Home Omit
Home Access
Entry
Instant Siren
Home access
Entry
Go to the app menu, select Settings > Alarm Settings >
System Settings.
Entry
Home Access
Entry
Triggers
Countdown
Entry
Supervision off as default (recommended).
Please note that having supervision enabled could reduce the battey life of your devices.
This feature should only be used by a professional installer to check for outage and malfunctions with
your devices. Incorrect usage would lead to a supervision failure message showing on the app.
With the exception of the PIR Image Camera, PIR Video Camera and Smoke Detector (these always
have supervision turned on), the other devices you will need to have supervision manually enabled on
the device if required.
Supervision can be enabled via Settings > Alarm Settings > System Settings > General Configuration.
Jamming and interference
detection (default on).
20
If jamming and interference is of concern, please
enable via “Settings > Alarm Settings > System
Settings > General Configuration’’
21
Adding & using devices•
Key Fob
/
Adding & Using Devices•
Key Pad
Manually requesting PIR Images
Initialisation
During an alarm, the PIR Image Camera will send
images to your phone. You can also manually
request these images in the ‘control’ section of the
app by pressing the image icon next to the device
in the contol list. Still images take an average of 15
seconds before showing on your phone. Click on
“image” to view images.
Go to app menu and select Control
IMPORTANT: If you purchase a Key Pad seperately to your
kit, you will need to initialise it before you learn it in for use
with your Smart Hub.
Panic
1
2
7
8
4
Away
/
• Use the Key fob to remotely arm, part arm or
disarm your alarm when within 30m range of
your Smart Hub.
• To add a Key Fob, see page 11.
• Pressing the panic button on the key fob will
immediately sound the alarm.
• To cancel the panic alarm you will need to enter
your PIN code on your Key Pad.
Panic button A
Yale
Part Arm
5
0
3
6
9
Panic button B
LED
Learn button=
Press 8 and 9 together
Disarm
Part arm
HomeArm
Note: Up to 50 images can be kept in the Yale
Server (the oldest images are automatically deleted
to make space). Users are advised to delete
unwanted images. Images will be stored for no
longer than 30 days.
Take Photo
1 Press ‘Panic button A’ followed by factory
default Key Pad code ‘0000’.
2 The LED will now flash slowly indicating it is in
test (programming) mode.
3 Press ‘Panic button A’ followed by the ‘7’ key
to set the Key Pad into slave mode.
4 Quit test mode by pressing the disarm key
twice.
5 You are now ready to learn this in to your
system (see page 9).
View Photo
22
23
CHANGE
Adding & Using Devices• (IT) Associazione/test
BATTERY- (DE) Verbinden/Testen -
Adding & Using Devices•
Reset Key Pad Code
Smoke Detector
Pair / Test button
e batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
3
Reset to factory default (0000) using the following steps:
Smoke Detection
2. Remove
1. Unscrew
When smoke is detected the device will activate for a minimum of 10 seconds with a two
(15)
tone alarm and flashing LED.
CR 2032
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation (DK) Installation.
CHANGE
BATTERY
7
2
Pressing the test button when in an alarm condition will silence the alarm for 10 minutes. It
will automatically resume smoke detection again after this period.
1
SR-KP
3. Hold down number 3 to discharge and then insert the
new battery.
Pair / Test button
1
CR 2032
3
4. Replace cover
Recalibration
Pair / Test button
5.
Initiliase your Key Pad. See previous page 22.
SR-DC
(IT) Associazione/test - (DE) Verbinden/Testen (NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
6. Learn this into your system.
r
secs
Radio 10
868MHz
1
Ø 5mm
+
If there is a system fault, you will need to press the Arm/
Home Arm button for a second time to “force arm” the
system.
3 x 1.5v AAA
24
Panic button
2.3m
3
Press and hold down the red button for 10 seconds.
Router
NOT INCLUDED
Resetting the system after a Panic Alarm
• Press the panic buttons together for 3 seconds to activate
PIN CODE
the alarm.
SR-PIR / PETPIR
Silence an Alarm
Silencing the alarm with the Panic Button does not reset the system. If the alarm is armed prior to activation,
the system will re-arm after being silenced with the Panic Button.
3 x 1.5v AAA
• Deactivate a panic event by pressing the disarm button
followed by your PIN code.
SR-EIR
(IT) Associazione/test - (DE) Verbinden/Testen (NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
Press thePress
2 panic
for
thebuttons
2 panictogether
buttons together
for
3 seconds
to activate
panic alarm.
3 seconds
to aactivate
a panic alarm.
Using your Panic Alarm
n
Pair /the
Test button
Press and hold
red button for at least 3 seconds to activate a panic alarm.
2
2 x 1.5v AA
ar
ry Le
BantteOff>
<O
>3s
Powe
SR-PC
Armed
SR-PB
LAN
>3sec.<
>3sec.<
Part Armed
Radio 868MHz
Activate an Alarm
Panic button
Panic button
4
Panic Button
4
110°
he system will require a reset at the Smart Hub after being silenced with the Panic Button. To reset the
T
Radio 868MHz
Smart Hub unplug the AC power (a) and turn the battery switch off for 10 seconds.
Turn the battery switched
back on and plug in theØAC
power
again.
5mm
>3sec.<
a
(a)
er
Pow
ar
ery Le
BanttOff>
<O
n
<On Off>
tery
Bant Off>
<O
b
LAN
Press the 2 panic buttons together for
3 seconds to activate a panic alarm.
a
25
b
OR
Learn
+ PIN+CODE
PIN CODE
11
2 x 1.5v AA
a
Off y
>
1
The Smoke Detector might need recalibrating after time to ensure it is working
at its optimum. This is done
(09)
LED flashes and beeps after 10 seconds. The Detector will
(GB) Setting up - (IT) Configurazione - (DE) Einstellung by pressing
andavholding
the test
until- the
(NO) Tilkobling
og montering
alarmsentralen
- (SE)button
Driftsättning
(DK) Opsætning.
then start its self calibration routine.
r <OBatter
n
CR 2032
Disarmed
Smoke Detector testing should be done on a regular monthly basis. Pressing the test button will make
(GB) How
does
it workthe
- (IT)button
Come funziona
the LED flash, the audible sounder chime and will send a test signal to the Smart
Hub
when
is - (DE) Wie es funk
(NO) Hvordan virker det - (SE) Hur fungerar det - (DK) Hvord
released. If nothing happens after pressing the test button, it indicates the batteries will need changing (see
SR-KF
page 26).
Powe
CR 2032
Testing
(IT) Associazione/test - (DE) Verbinden/Testen (NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
(GB) Tamper alarm - (IT) Allarme effrazion
(SE) Manipulationslarmet - (DK) Destrukt
(24)
GB - Fault Status
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel
- (NO) Batteribytte SR-EIR
(SE) Batteribyte - (DK) Batteriskift.
IT - Guasto Stato
(24)
DE - Fehlerstatus
•
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel•- (NO) Batteribytte
3 x 1.5v AAA
NO
- Feil Status
(SE)
Batteribyte
- (DK) Batteriskift.
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation SE - Felindikering
(DK)
Installation.
External
Siren
Battery Change
Always use the correct type of batteries as replacements because any other battery type canDK
cause
- Fejlstatus
Changing Batteries
Changing Batteries
7 arming
When the batteries start getting
3 x 1.5vlow
AAAthe Siren will produce a series of audible pips and flashes when
and disarming.
SR-RS
problems with the operation of the system. Ensure the correct steps are taken when changing
batteries in tamper protected devices.
1
2
a
GB - PANEL MODE
Low Battery Indicator
b
IT - Modalitá Pannello
The Hub will start to emit an intermittant beep to indicate that the batteries need changing on one of your
DE - Panel-Modus
devices.
SR-RS
2 x AA a low battery warning with a tamper warning.
Note: Take care not to confuse
(Lithium 3.6V)
Tamper Warning: Series of beeps when armed, silent when disarmed.
Low Battery: Series of audible pips when armed and disarmed.
NO - Panel Mode
The hub will continue to beep until the batteries on this device have been replaced, or low battery device
SE -isLarmstatus
put into bypass mode. Please note that bypass mode disables the device, and if disabled this device will no
DK - Panel tilstand
longer be triggered when the alarm is armed.
The app will also display a low battery message under the relevant device when batteries are running low.
SR-SR
SR-EIR
2 x AA
(Lithium 3.6V)
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte (SE) Batteribyte - (DK) Batteriskift.
3
2.
1. Disarm
> Settings
> Devices
> External Siren
> Change battery
SR-EIR
(GB) Reset - (IT) Reset - (DE) Reset - (NO) Tilbakestill - (SE) Återställning - (DK) Nulstil .
CHANGE
BATTERY
(21)
rn
er
Pow
ea
ery L
BanttOff>
<O
tery
Bant Off>
<O
b
SR-SR
4.
3.
4 x 1.5v D
a
<On Off>
<On Off>
5.
rn
4 x 1.5v D
LAN
er
Pow
ea
ery L
BanttOff>
<O
d
LAN
Remove old batteries and wait
for 30 secs before replacing
with 4 new
ones.
SR-BX
c
CR 2032
Ø 5mm
Switch off
4 x 1.5v D
KP
DC
SR-SR
CR 2032
SR-BX
4 4 x 1.5v D
6.
When a device first shows the low battery signal in the app, it has enough capacity to operate for
approximately 1 month before complete exhaustion.
Always make sure the system is disarmed before changing any batteries. We recommend you follow the
battery wizard within the app when changing the batteries.
2 x 1.5v AA
7.
5
a
b
Turn on. Check
the siren beeps &
flashes.
6
8. > Done
Replace the cover
Warning: After the batteries have been inserted, the tamper
will become active after three hours.
PC
SR-BX
3 x 1.5v AAA
26
27
CHANGE
BATTERY
BATTERY
Changing Batteries•
(22)
Changing Batteries•
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte (SE) Batteribyte - (DK) Batteriskift.
CHANGE
BATTERY
CR 2032
CR 2032
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(SE) Batteribyte - (DK) Batteriskift.
Door/Window
Contact Battery Change
When the battery is low the LED will light up when the door/window is opened.
CR 2032
Note: Door/Window Contact case tamper conditions are also indicated by a lit LED,
check the tamper before
changing the battery.
CHANGE
BATTERY
SR-KP
SR-KP
To change the battery:
(23)
PIR Video Camer Battery Change
(23)
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte (SE) Batteribyte - (DK) Batteriskift.
3 x 1.5v AA
(Lithium)
SR-KP
CR 2032
CR 2032
CR 2032
1. Disarm
CR 2032
2. Unscrew
& remove
SR-PVC top case
3. Remove &
replace Batteries
4. Refit.
3 x 1.5v AA
(Lithium)
1. Disarm
(22)
SR-KP
2. Unscrew SR-DC 3. Remove cap
4. Remove battery
5. Insert new
6. Refit.
(GB) Changing batteriestop
- (IT)case.
Sostituzione batterie - (DE) Batteriewechsel - (NO)
Batteribytte battery
SR-DC
(SE) Batteribyte - (DK) Batteriskift.
SR-DC
2 x 1.5v AA
2 x 1.5v AA
PIR BatterySR-PC
Change
(22)
3 x 1.5v AAA
2 x 1.5v AA
SR-PC
When the battery is low the LED will flash when any motion is detected. The batteries are changed as
follows:
CR 2032
3 x 1.5v AAA
3 x 1.5v AAA
SR-PC
SR-PIR / PETPIR
EF-PIR
CR 2032
CHANGE
BATTERY
SR-PC
SR-DC
SR-KF
(22)
1.
SR-KF
Disarm
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte (SE) Batteribyte - (DK) Batteriskift.
2. (GB) Changing batteries
3. - (IT) Sostituzione batterie
4. - (DE) Batteriewechsel - (NO) Batteribytte Unscrew
&
(SE) Batteribyte
- (DK)
Batteriskift.
Replace cover
Remove
remove
& replace
3 x 1.5v AA
battery
3 x 1.5v AAA
3 x 1.5v AA
Alkaline
SR-KP
PETPIR
1. Disarm 2. SR-PIR /3.
SR-PIR /Remove
PETPIR
SR-PIR / PETPIR
Unscrew
& remove Batteries
top case
CR 2032
When the battery is low the LED will glow dimly when any key is pressed. The battery is changed as follows:
2 x 1.5v AA
CR 2032
Please ensure battery
is inserted correctly.
SR-PVC
Key
Fob Battery Change
3. Insert
new
Batteries
4. Refit.
CR 2032
Ensure tamper spring is fully
depressed when re-fitting the PIR to
the back case. If this has not been
done correctly this will be indicated by a
flashing LED on the PIR.
Press any key and check that the LED lights. If the LED lights the new battery installation is successful.
CHANGE
BATTERY
CHANGE
BATTERY
Key Pad Battery
Change
SR-SD
SR-SD
When the battery is low the LED will flash when any key is pressed. The battery is changed as follows:
CR 2032
CR 2032
SR-DC
CR 2032 CR 2032
PIR Camera Battery Change
2 x 1.5v AA
Alkaline
1. Disarm SR-KP
2. Unscrew &
SR-KP remove cover
1. Disarm
SR-PC
2.
Unscrew
& remove
top case
3. Remove old & insert
new Batteries
Please be careful
when removing case
as cable is very
delicate.
4. Refit.
3 x 1.5v AAA
5. Replace cover.
4. Insert new
battery (slot under
SR-PB
2 tabs) & click in
place. CR 2032
SR-PB
Press a number key and check that the LED lights. If the LED lights the new battery
installation is
CR 2032
successful.
3. Remove old
battery
SR-DC
28
SR-PIR / PETPIR
SR-DC
2 x 1.5v AA
2 x 1.5v AA
29
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte CR 2032
(SE) Batteribyte - (DK) Batteriskift.
(23)
Changing Batteries•
Troubleshooting•
External Siren
Smoke Detector Battery
3 x 1.5v AA Change
(Lithium)
SR-KF
When the battery is low the LED will flash accompanied by a low volume beep once every 30 seconds.
SR-PVC
1.
Rotate anticlockwise to
remove
2. Remove
old
batteries
Siren produces a series of audible pips
when armed or disarmed
4.
Fit & rotate
clockwise to lock.
3.Insert
new
batteries
CR 2032
SR-KF
Press the test button and check that the LED lights and the sounder chimes to confirm the new battery
installation is successful.
3 x 1.5v AA
SR-PB
Panic Button Battery Change
When the battery is low the LED will glow dimly when the button is pressed. The battery is changed as
follows:
SR-SD
CR 2032
SR-PB 1. Unscrew
2. Open case
3. Remove
old battery
Siren produces a 3 second alarm
when disarmed
• There has been a previous alarm and there might
be an intruder still in the premises.
3 x 1.5v AA
CR 2032
SR-SD
4. Insert new
battery & replace
cover.
Press the button and check that the LED lights. If the LED lights the new battery installation is
successful.
• If the Siren produces a series of pips when arming
and disarming this indicates low batteries. Check
your app for confirmation of battery status.
• If the Siren produces a series of pips only when
arming this indicates a tamper fault. Check that
the Siren cover is firmly secured and the tamper
spring on the back of the Siren is fully depressed
when in contact with the wall. If not use suitable
packing material to fill the gap).
Siren produces an interrupted tone when
sounding an alarm
• Low battery warning. Check your app for battery
status. Change batteries (see page 27).
Siren does not respond to Arming or
Disarming
• Siren batteries may be completely exhausted.
Check your app for confirmation of battery status.
See instructions for changing batteries on page
27.
• Siren may not be learnt-in. If Siren produces a
tamper alarm when the cover is removed and the
Siren is OK, learn-in the Siren (see page 11).
• Siren may not be in range of the Smart Hub
Ensure these are within 30m of each other and
relocate devices if required.
Adding the External Siren
• Ensure the dip switch positions are as shown
in the diagram. If the switches are in the wrong
position, please change accordingly
30
• After changing the
dip switch, turn off the
power for 30 seconds,
then turn the power on
again for the changes to
take effect
Door/Window Contact
Door/Window Contact LED lights up
• Batteries are low or the tamper switch has been
disturbed. Check that the tamper switch spring is
making contact with the mounting surface. If the
tamper switch is OK, please change the battery.
Door/Window Contact does not respond
to opening when jumper is in the test
7
position
1
(14)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Ins
(DK) Installation.
2
• Batteries are completely exhausted. Change the
battery.
• The magnet is too far away from the sensor.
Check that the gap between the sensor and
magnet is not greater 3
than 10mm.
PIR Motion
Detector
a
4
max 10mm
5
or
PIR does not respond to motion
• Previous motion may have triggered the PIR
sleep timer, and is preventing subsequent motion
detection. Arm the system and the vacate
protected area for at least 60 seconds before
testing. By pressing the learn/test button the PIR
6
LED will light up and detect
motion for the first
minute.
b
PIR Motion Detector is slow to respond
• This is normal. The PIR Motion Detector has
sophisticated false alarm filtering to filter out
random fluctuations, and responds to genuine
motion across field of view, the PIR is less
sensitive, when walking directly towards it.
a
31
7
(10)
4
Troubleshooting•
PIR Motion Detector gives false alarms
• Check pets have no access to the protected area.
• Check that the PIR Motion Detector is not
pointed at sources of heat or moving objects, e.g.
fluttering curtains.
• Check that the PIR Motion Detector is not
mounted above convector heaters or pointing
directly at windows.
It is possible to arm the system with
“open” Door/Window Contact
(i.e. windows open).
You will be prompted in the App when trying to
arm with your door/window open.
PIR Motion Detector LED flashes
• Batteries are low or the tamper switch is
disturbed. Check your app for device battery
status. Change them if they are running low.
Check that the tamper switch spring is making
contact with base.
(GB) Setting up - (IT) Configurazione - (DE) Einstellung (NO) Tilkobling og montering av alarmsentralen - (SE) Driftsättning (DK) Opsætning.
Specifications•
All devices
Smart Hub LED 2 (Warning LED)
Environmental Conditions
GB - Network
IT - Rete
DE - Netzwerk
NO - Nettverk
Network
SE - Nätverk
DK - Netværk
HOME SERVER
-10°C to 40°C, relative humidity 70% noncondensing for all units except the external Siren.
Siren: -20°C to 50°C, relative humidity 95% noncondensing
GB - Fault Status
IT - Guasto Stato
DE - Fehlerstatus
Fault Status
NO - Feil Status
SE - Felindikering
DK - Fejlstatus
Radio operational range
GB - PANEL MODE
IT - Modalitá Pannello
DE - Panel-Modus
Mode
NO - Panel
Panel Mode
SE - Larmstatus
DK - Panel tilstand
Housings ABS/polycarbonate
30m in a typical domestic installation, range can vary
depending on building construction, device positions
and RF environment
Smart Hub 2.0
(GB) Reset - (IT) Reset - (DE) Reset - (NO) Tilbakestill - (SE) Återställning - (DK) Nulstil .
r
arn
tery Le
Batn Off>
<O
ry
BantteOff>
<O
<On Off>
<On Off>
r
Powe
LAN
arn
tery Le
Batn Off>
<O
Powe
LAN
PIR Motion Detector does not respond to
movement
32
Radio 868MHz FM
Power supply 4.5V, 3 x AA alkaline batteties
Tested to EN54
Radio 868MHz FM
Power supply 3V, CR2032 lithium coin cell battery.
PIR Motion Detector
Should you have any questions or experience a
problem with your Smart Home Alarm Kit, please
check our troubleshooting sections within the app.
(select the ? at top right of the screen you need
help with) Or alternatively go to our FAQ section at
yale.co.uk/help.
Smoke Detector
External Siren
PIR Image Camera & PIR Video Camera
Consumer Support
Alarm processing Microprocessor controlled dual
edge sequential pulse count with pulse length
discrimination
Radio 2.4GHz
Power supply 3 x AA Lithium batteries.
Motion Detector range 12 metres 110O
Key Fob
• Batteries are completely exhausted. Check your
app for device battery status. Change the batteries.
• Device out of range of the Smart Hub.
* If a PIR Image Camera or PIR Video camera is not
learnt into the system or within range of the Smart
Hub, battery life will be greatly affected while it
searches for a connection.
PIR Video Camera
Siren Output 100dBA sound
pressure @ 1m minimum
Zones 20 radio devices
Radio system 868MHz FM, 2.4GHz
Power supply Plug top adaptor type, input 230VAC
50Hz, output 9VDC, 1A, tested to EN 60 950
Rechargeable battery Ni-MH, 4.8V 600mAH,
charge time 72hrs, standby
time 10hrs
Siren Output 104dBA sound
pressure @ 1m minimum
Radio 868MHz FM
Power supply 6V, 4 x D alkaline batteries.
LED flashes every 20 minutes
Power supply 2 x AA 1.5V alkaline batteries
Movement detection range 110°
Alarm processing Microprocessor controlled dual
edge sequential pulse count with pulse length
discrimination
Radio 868MHz FM
Power supply 4.5V, 3 x AAA alkaline batteries.
Motion Detector range 12 metres 110O
Door/Window Contact
Radio 868MHz FM
Power supply 3V, CR2032 lithium coin cell battery
Radio 868MHz FM
Power supply 3V, CR2032 lithium coin cell battery.
Key Pad
Radio 868MHz FM
Power supply 3V, CR2032 lithium coin cell battery.
Panic Button
Special notes on compatibility:
This alarm system is NOT compatible with HSA6000
series and HSA3000 series accessories. Please
note the prefix “EF” or “SR” on the front of the part
number to indicate compatibility.
The phone feature and remote notifications require
our central server. Yale does not guarantee limitless
and future availability of our free server. We would
contact individual users via e-mail should this
situation change.
In the unlikely event of server disconnection, the
alarm system will continue to function (arm/disarm)
using the supplied Key Pad accessory.
PIR Image Camera
Alarm processing Microprocessor controlled dual
edge sequential pulse count with pulse length
discrimination
Radio 2.4GHz
33
Notes
34
Notes
35
Conexis L1
Hereby, ASSA ABLOY Ltd., School Street, Willenhall, West Midlands, England Wv13 3PW declares
that the radio equipment type SR-310, SR-320, SR-330, SR-340 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet
address: www.yale.co.uk/declaration-of-conformity
An ASSA ABLOY Group brand
NoPb
WEEE
Note: Waste electrical products
and batteries should not be
disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or
retailer for recycling advice.
/YaleUK
/YaleSecurity
THE YALE BRAND, with its unparalleled global reach and
range of products, reassures more people in more countries
than any other consumer locking solution.
THE ASSA ABLOY GROUP is the world’s leading
manufacturer and supplier of locking solutions, dedicated to
satisfying end-user needs for security, safety and convenience.
/YaleSecurityUK
The smarter way to protect your home•
Issue No. 2A
">