advertisement
Low radiation cordless DECT/GAP telephone
DF921
Operating Intructions
2
Safety Information
1 Safety Information
Please read this operating instruction manual thoroughly.
Intended use
The telephone is suitable for telephoning within a public telephone network system. Any other use is considered unintended use. Unauthorised modification or reconstruction is not permitted. Under no circumstances open the device or complete any repair work yourself.
Installation location
Prevent excessive exposure to smoke, dust, vibration, chemicals, moisture, heat and direct sunlight.
Do not use the handset in potentially explosive areas.
Power adapter plug
Attention: Only use the power adapter plug supplied because other power supplies could damage the telephone. Ensure access to the power adapter plug is not obstructed by furniture or such.
Rechargeable batteries
Attention: Never throw batteries into a fire. Only use batteries of the same type.
Pay attention to correct polarity. Incorrect polarity of the batteries represents a risk of explosion during charging.
Power failure
The telephone cannot be used to make calls in the event of a power failure. Always keep a cord connected telephone which operates without an external power supply available in case of emergency situations.
Medical equipment
Attention: Never use the telephone in the vicinity of medical equipment. Effects on such equipment cannot be fully ruled out.
DECT 1 telephones can cause an unpleasant humming sound in hearing aids.
Disposal
In order to dispose of your device, take it to a collection point provided by your local public waste authorities (e.g. recycling centre).
The adjacent symbol indicates that the device must not be disposed of in normal domestic waste! According to laws on the disposal of electronic and electrical devices, owners are obliged to dispose of old electronic and electrical devices in a separate waste container.
Batteries must be disposed of at the point of sale or at the appropriate collection points provided by the public waste authorities.
Packaging materials must be disposed of according to local regulations.
1
DECT : D igital E nhanced C ordless T elecommunication = Standard for cordless telephones.
Preparing the Telephone
2 Preparing the Telephone
Safety information
Attention: It is essential to read the Safety Information in Chapter 1 before starting up.
Checking the package contents
The package contains:
1
Content
Base station with power adapter plug
Charging station with power adapter plug
Handset
Telephone connection cable
Batteries
Operating instructions
921
1
−
1
1
2
1
Model DF92x
1
922
1
1
2
1
4
1
923
1
2
3
1
6
1
8
1
4
1
924
1
3
Connecting the base station
Attention: Position the base station at least 1 meter away from other electronic devices, otherwise there is a risk of mutual disturbance.
Connect the base station as illustrated in the diagram. For reasons of safety, only use the power adapter plug and telephone connection line supplied.
Mains power outlet Telephone line socket
For the base station, use the power adapter plug labelled with SW−075030EU and output data 7.5 V DC, 300mA.
Inserting the batteries
Open the battery compartment and insert the batteries. Only use batteries of the type AAA NiMH 1.2 V.
Pay attention to correct polarity.
Close the battery compartment cover.
1 Visit www.switel.com to find out whether the telephone/telephone set is already available.
3
4
Preparing the Telephone
Charging the batteries 2
Before the handset is used for the first time, insert it in the base station / charging station for at least 14 hours.
When the handset is inserted in the base/charging station properly, you will hear an acoustic confirmation signal and the charge control lamp lights up. The handset warms up during the charging process. This is normal and does not represent a risk. Do not charge the handset with charging units from other manufacturers.
The current battery charge status is indicated in the display:
Full Half empty Low Empty
Setting the display language
Select a language (cf. Menu Structure"):
> PERS. EINST > SPRACHE > ... ( > PERSONAL SET > LANGUAGE >...)
Setting the time and date on the handset
The time and date are set via the menu. Refer to Page 14 for the sequence of menu option
selections.
Auto answer / Auto hang−up
If this feature is enabled, the telephone automatically takes a call when the handset is removed from the base station and automatically ends the call when it is put back in the base
station. Use the menu to activate or deactivate these functions. Refer to Page 15 for the se-
quence of menu option selections.
Private branch exchanges
The information on Page 16 explains how to install your telephone in a private branch ex-
change.
Low−radiation operation (ECO mode)
The level of radiation is considerably lower than that of standard DECT cordless telephones when in Standby mode (when the handset is on the base station).
In talk mode, radiation is reduced (depending on the distance between the handset and base station).
Default setting = ECO MODE → OFF
The telephone can be set up so that the radiation frequency is reduced;
If necessary, you can increase the range of the telephone system by switching
ECO mode off;
→
OFF).
Operating Elements
3 Operating Elements
The buttons in this operating manual are subsequently depicted with a uniform contour.
Therefore, slight deviations in the appearance of the symbols on the telephone buttons compared to those depicted here are possible.
Handset
1 Loudspeaker
2 LC display
3 Delete button / Redialling
4 Scroll up button
5 On−hook button / Standby mode
6 Scroll down button
7 Digit keys
8 # button
Ringing tone off/on
9 Internal call
10 Microphone
11 Handsfree button
12 * button
Key lock
13 Call button / R−button
14 Menu button
14
13
12
11
1
2
3
4
5
6
7
8
9
10
Base station
15 Paging button
16 Charging contacts
15
16
4 Preliminary Information
This chapter provides basic information on using the operating instruction manual and the telephone.
Description of operating sequences in the manual
Display
¾
Description
Displays the appearance of buttons
Press the button depicted briefly
5
6
Preliminary Information
3 sec.
{ }
Press the button depicted for 3 seconds
Enter digits or letters
Handset rings
Remove the handset from the base station
Place the handset in the base station
Depicts text in the display
Icons and texts in the handset display 3
Icon Description
On: Indicates the battery charge status.
Flashing: The batteries must be charged.
Run−through segments: The batteries are being charged;
1 Internally assigned call number of the handset;
01/01 12:03
Display of date and time;
On: A call is currently being made.
Flashing: A call has been received;
On: The call log is open.
Flashing: New calls have been registered in the call log
You have opened the phone book;
u
There are further items/menu options. Press or to show them.
Press to confirm your selection.
Press the ¿ button to delete a character or skip back one menu level.
The ringing tone has been switched off;
KEYS LOCKED
The handsfree facility is activated;
The key lock function is activated;
MUTE ON
The alarm function is activated;
The microphone is deactivated (muted);
On: The connection to the base station is good.
Flashing: The connection to the base station is interrupted. Move nearer to the base station.
Preliminary Information
Standby mode 4
All descriptions in this operating manual assume that the handset is in Standby mode, which is the case when you are not talking on the phone and if a menu is not open. Press enable Standby mode as necessary.
5
to
Energy−save mode
When the handset has been in Standby mode for some time, it automatically switches to energy−save mode. The buttons and display no longer light up.
Navigating in the menu 6
All the functions can be accessed via the various menus.
Refer to Menu Structure
Page 14 for information on how to access each respective func-
tion.
Open the main menu
or Select a submenu
Open the submenu
or Select a function
Open the function
or Select a setting
Use the keypad to enter digits or letters as necessary
¿
Confirm your entries
Move one level back
Cancel all programming and saving and return the handset to Standby mode
Every process is automatically cancelled if there is no input within 15 seconds.
Creating phone book entries − example 7
The way in which to navigate through the menus and select settings is explained by means of the example Creating phone book entries . Proceed as in this example for all the settings.
Open the main menu
/ PHONEBOOK , Select the menu and confirm it
,
,
/ NEW ENTRY , Select the submenu and confirm it
Enter a name (max. 12 characters) and confirm it
Enter the phone number (max. 24 digits) and confirm it
/ GROUP B , Select the group and confirm it
Cancel the saving process and return the handset to Standby mode
7
8
Phone Book
5 Phone Book
You can use the phone book to store up to 100 phone numbers together with the associated names.
Always enter the area access code with the phone numbers so that incoming local calls can also be assigned to a phone book entry.
When the memory capacity is used up, the message MEMORY FULL appears when an attempt is made to store another number. To create space, an existing entry must first be deleted.
The phone book entries are arranged alphabetically. To access the required phone book entry directly, press the first letters of the corresponding name.
Entering names
Letters are also imprinted on the digit keys. Letters, digits and special characters are entered by pressing the relevant key the respective number of times.
¿
or
Enter a space
Delete a character
Move the cursor
To enter the same letter twice, press the button to enter the letter. Wait until the cursor skips one position forwards. Enter the letter again.
Creating phone book entries 8
Refer to the example;
9 Editing phone book entries
or
Open the phone book
Select an entry
Open the menu
,
/ EDIT ENTRY ,
,
/ GROUP B ,
Deleting phone book entries
Deleting an entry
or
Select the submenu and confirm it
Change the name and confirm it
Change the phone number and confirm it
Change the group and confirm it
Open the phone book
Select an entry
Open the menu
/ DELETE ENTRY , Select the submenu and confirm it
CONFIRM ? , or
¿
Confirm or cancel deletion
Deleting all entries
Open the main menu
Phone Book
/ PHONEBOOK ,
/ DELETE ALL ,
CONFIRM ? , or
¿
Select a menu and confirm it
Select the submenu and confirm it
Confirm or cancel deletion
Exchanging the phone book
In order to exchange the phone book, several DF92x handsets or handsets from the same series (HS1, HS2, ...) need to be registered to the base station.
HS1: Open the main menu
/ PHONEBOOK ,
/ PB TRANSFER ,
or
Select the menu and confirm it
Select the submenu and confirm it
Select a handset (target handset here: HS2)
Activate the copy process
HS2: TRANS. FROM: , Start copying
HS1 and HS2: DONE!
Transfer complete
Quick dial 10
Phone numbers from the phone book can be assigned to digit keys 1 to 9.
Saving phone numbers as quick dial numbers
Open the main menu
/ PHONEBOOK ,
/ DIRECT MEM ,
/ ,
Select a menu and confirm it
Select the submenu and confirm it
Select a quick dial button
An existing entry appears if there is one, open the options
ADD ,
/
Open the menu
Select a phone book entry
Assign the entry to a quick dial button
Deleting quick dial numbers
Open the main menu
/ PHONEBOOK ,
/ DIRECT MEM ,
/ ,
DELETE ,
CONFIRM ? , or ¿
Select a menu and confirm it
Select the submenu and confirm it
Select a quick dial button
An existing entry appears if there is one, open the options
Open the menu
Confirm or cancel deletion
9
10
Call List
6 Call List
11
The call list stores up to 50 phone numbers.
The caller number display ( CLIP
1
) is a supplementary service offered by your telephone network provider. The caller’s number appears in the display if the service is offered by your telephone network provider. Contact your network provider for further information.
Messages in the display:
UNKNOWN The phone number is received only partially or with errors.
OUT OF AREA
WITHHELD
Information related to the phone number is not available. This could signify an international call.
The caller has suppressed the transmission of their phone number.
Displaying numbers in the call list
Open the call list
or Select an entry
Only the first 12 digits of a phone number are shown.
Press
¿
to display any further digits.
Storing a phone number in the call list in the phone book
A phone number in the call list can be stored in the phone book directly.
Open the call list
/ ,
/ SAVE NUMBER ,
Select an entry and confirm it
Select the menu and confirm it
,
,
Enter a name (max. 12 characters) and confirm
Change the phone number as necessary
(max. 24 digits) and confirm
/ GROUP B , Select a group and confirm it
As soon as the phone number in the phone book has been saved together with a name, the name entered appears in the call list.
Deleting individual phone numbers
Open the call list
Select an entry and confirm it / ,
/ DELETE ,
CONFIRM ? , or
¿
Select the menu and confirm it
Confirm or cancel deletion
1 CLIP: C alling L ine I dentification P resentation = Displays the caller’s phone number.
Telephoning
Deleting all phone numbers
Open the call list
, /
DELETE ALL ,
CONFIRM ? , or ¿
Select the menu and confirm it
Confirm or cancel deletion
7 Telephoning
Taking a call
¾ , or
Ending a call
or
Take the call
End a call
Making a call
¿
¾
or
Enter the phone number (max. 24 digits)
Delete the last digit if incorrect
Dial the phone number
Redialling
The telephone stores the last 10 numbers dialled in a redialling list.
¿
, or Open the redialling list and select an entry
¾ or Dial the number
Editing phone numbers in the redialling list is identical to editing phone numbers in the call list; Chapter 6.
Calling back calls received
Your telephone stores 50 calls received in a call list.
, or Open the call list and select an entry
¾ or Dial the number
Dialling numbers from the phone book
Phone numbers must have been stored in the phone book for this function;
, or Open the phone book and select an entry
¾ or Dial the number
Quick dial
Be sure to store phone numbers as quick dial numbers first;
3 sec. Press any of the quick dial buttons
Internal calls 1 12
Making internal calls
There must be two or more handsets (HS1, HS2, ...) registered on the base station in order to make internal calls free of charge.
1 Internal calls are only possible when at least two handsets are registered in the system;
Checking the contents of the package" on Page 3.
11
12
Telephoning
HS1: , e.g.
Press
Select the internal number of the handset you wish to phone
to call all registered handsets at the same time.
HS2: ¾
HS1/HS2:
Forwarding external calls internally
HS1: , e.g.
Other handset answers the call
End the internal call
HS2:
¾
HS1:
Dial the internal handset number while making the external call
Other handset answers the call
Forward the call
If the handset called does not answer, take the external call back by pressing .
Holding a call / brokering
While a call is in progress, it is possible to dial another handset in order to consult with someone. The external caller is put on hold while you converse with the second, internal person called. You can repeat this procedure as often as required.
HS1: , e.g. Dial the internal handset number while making the external call
HS2: ¾
HS1:
Other handset answers the call
Switch between the callers
Making conference calls
An external call can be transferred to another internal handset for a conference call.
HS1: , e.g. Dial the internal handset number while making the external call
HS2: ¾
HS1: 3 sec.
Other handset answers the call
Start the conference
HS1 / HS2: End the conference
Setting the receiver volume
The volume can be adjusted to one of 5 levels during a call.
or Select a volume level
Displaying the duration of a call
The duration of the call you are making is shown on the display.
Handsfree 13
This function is used to listen to the caller via the loudspeaker.
Enable the handsfree function
Disable the handsfree function
Menu Structure
Muting the microphone in the handset 14
The microphone in the handset can be turned off / on while making a call.
¿
Deactivate the microphone (muting on)
¿ Activate the microphone
Key lock 15
The key lock feature prevents functions assigned to buttons being activated accidentally.
3 sec. Lock the keys
3 sec. Unlock the keys
Handset ringer melody 16
The handset’s ringer melody can be turned off.
3 sec. Turn off the ringer melody
3 sec. Turn on the ringer melody
Searching for the handset (Paging)
If you have mislaid your handset, you can sound a paging tone to find it.
Base station , Sound the paging tone
or Stop sounding the paging tone
Switching the handset off and on
You can switch the handset off to save the batteries.
3 sec. Switch the handset off
3 sec. Switch the handset on
8 Menu Structure
Main menu
Press to display the main menu. Then use the and buttons to select an entry and confirm it by pressing the button.
Further information on the menu and operation;
17
13
14
Menu Structure
PHONEBOOK
NEW ENTRY
LIST ENTRY
ENTER NAME
EDIT ENTRY
ENTER NUMBER
ENTER NAME
NO GROUP
GROUP A, B, C
ENTER NUMBER
NO GROUP / A, B, C
18
CONFIRM ?
DELETE ALL
DIRECT MEM
CLOCK/ALARM
DATE & TIME
SET ALARM
DELETE ENTRY
CONFIRM ?
KEY 1−9 ADD
DATE:
OFF
ON ONCE
ON DAILY
MELODY 1
TIME:
TIME:
TIME:
ALARM TONE
PERSONAL SET
HANDSET TONE
HANDSET NAME
RING VOLUME
RING MELODY
GROUP MELODY 1
KEY TONE
FIRST RING
ENTER NAME
RINGER OFF
LOW
MEDIUM
HIGH
BOOST
PROGRESSIVE
MELODY 1−10
GROUP A, B, C
ON/OFF
ON/OFF
MELODY 1−10
1 Use this function to assign a specific ringer melody to a group. Your handset will play this melody when a call is received from this group. This function requires that the caller number display ( CLIP
2
) is enabled.
2
CLIP: C alling L ine I dentification P resentation = Display the caller’s phone number.
Special Functions
AUTO PICK−UP
AUTO HANG−UP
LANGUAGE
BABYSIT MODE
ON/OFF
ON/OFF see 1
ON/OFF
ADVANCED SET
RECALL TIME
DIAL MODE
SHORT(100 ms)
MEDIUM (250 ms)
LONG (600 ms)
TONE
PULSE
PIN
2 CALL BARRING
BABY CALL
REGISTRATION
UNREGISTER
PIN
RESET UNIT
INTRUSION
ECO MODE
PIN
2
SELECT BASE
REGIST. BASE
PIN
2
PIN
2
CONFIRM ?
ON/OFF
ON/OFF
MODE
NUMBER 1−4
MODE
NUMBER
BASE 1−4
BASE 1 2 3 4
HANDSET 1−5
NEW
ON/OFF
ENTER NUMBER
ON/OFF
ENTER NUMBER
PIN
2
9 Special Functions
Dialling mode 19
The telephone can be operated in analogue exchanges (PULSE mode) as well as new, digital exchanges (TONE/DTMF mode). The dialling mode is controlled via the menu. Refer to
Page 15 for the sequence of menu option selections.
Alarm clock
The Alarm clock" function can be used so that you are alerted by the handset at a specific time.
1
2
Languages: English, French, German, Italian, Turkish and Dutch.
The PIN code is set to 0000" at the factory.
15
16
PABX / Supplementary Services
Babysit
You need two handset to use this function.
Place one of the handsets in the room you wish to monitor. Activate the the function on this handset. No further internal or external calls are signalled by this handset from this point.
You can then establish a connection to this handset from a second handset and monitor the room acoustically. Dialling the internal phone number of the handset placed in the room starts room monitoring. Room monitoring is stopped again by either putting the phone down or pressing the Call button.
Touch & dial
Use this function to store a set phone number that will be dialled automatically when any button (except ) is pressed.
Call barring
Use this function to ban certain phone numbers from being dialled. The call barring numbers must be entered separately for each handset. You can specify bar calls to up to 4 numbers each comprising up to 4 digits. All phone numbers whose first digits match the specified numbers will be barred. A useful benefit of this function is to bar international or long−distance calls, for example. Example: Call barring = 0185 . All numbers beginning with 018 5 will be barred. Numbers beginning with 018 0 , 018 1 , 018 8 , ..., will be dialled.
Intrusion mode
Enabling the INTRUSION function (see Menu Structure") allows you to link in handsets to the call made with another handset by pressing ¾ on the "intruding" handset.
10 PABX / Supplementary Services
R−functions on private branch exchanges
If your telephone is connected to a private branch exchange, functions such as call forwarding or automatic call back can be used via the R−functions . Refer to the operating manual provided with your private branch exchange as to which Flash time must be set in order to use these functions. The sales outlet where you purchased the exchange can provide information as to whether the telephone will work properly with the exchange. The Flash time
is set using the menu. Refer to Page 15 for the sequence of menu option selections.
R−functions and supplementary services
Your telephone supports supplementary services provided by your telephone network provider, such as brokering or conference calls. These supplementary services can be used by implementing the R−functions . Please contact your telephone network provider regarding which Flash time must be set to use the supplementary services. Contact your telephone network provider with regard to enabling supplementary services. The Flash time is set
using the menu. Refer to Page 15 for the sequence of menu option selections.
To enable the R−functions while making an external call:
, or
INIT 2NDCALL , Select the R−functions
or SWITCH CALLS /
CONFERENCE , Select and activate the function
Extending the Telephone System
Dialling pause
When using private branch exchanges, it is necessary to dial an access code to obtain the dialling tone for an outside line. When using some older private branch exchanges, it takes a little time before the dialling tone becomes audible. In the case of such private branch exchanges, a dialling pause can be inserted after the number for an outside line in order to continue dialling directly without having to wait for the dialling tone.
3 sec. Insert a dialling pause
The actual phone number is dialled a certain time after the number for an outside line.
The dialling pause can also be entered with the phone numbers in the phone book.
Caller number display (CLIP
1
)
The caller number display (CLIP) is a supplementary service offered by your telephone network provider. Contact your network provider for further information.
If this function is available with your telephone line, the number of the caller appears in the display when the phone rings. If the caller has suppressed transmission of his phone number, the corresponding message appears in the display. The phone number is not displayed and, as a result, is not stored in the call list.
Answering machine in the telephone network 20
An answering machine in the telephone network is a supplementary service offered by many telephone network providers. If your telephone network provider offers an answering machine in the telephone network for you, an icon on the display informs you of new messages received ( VMWI 2 ). This function can only be used when your telephone network provider actually offers the service. Contact your network provider for further information.
11 Extending the Telephone System
The international GAP
3
standard regulates the compatibility of handsets and base stations from different manufacturers. As a result, it is possible to integrate SWITEL devices and devices from other manufacturers together in one telephone system. It is possible, however, that some functions are not available.
Multiple handsets
Up to 5 handsets can be registered on the base station.
Registering handsets
Before starting to register a handset, switch the base station to Registration mode.
3 sec.
Enable Registration mode
Now register the handset,
Page 15. The currently valid PIN code is used for registration
purposes;
The handset is automatically assigned an internal call number following registration. The internal call number appears in the display.
1
2
CLIP: C alling L ine I dentification P resentation = Displays the caller’s phone number.
VMWI: V isual M essage W aiting I ndication = Visual indicator that new messages have been recorded.
3 GAP: G eneric A ccess P rofile = Standard for the interoperation of handsets and base stations from different manufacturers.
17
18
In Case of Problems
To register handsets from other manufacturers, please refer to the operating manual supplied with them.
Deregistering handsets
Each handset can deregister itself and other handsets registered on the base station. Following deregistration, UNREGISTERED appears in the display of the unregistered handset.
Handsets are deregistered via the menu. Refer to Page 15 for the sequence of menu option
selections.
Multiple base stations
You can increase the range of your handset by registering it on several base stations. The handset can be registered on up to 4 different base stations simultaneously. Each base station requires its own telephone line socket. Connections can be used with the same call number or with different ones.
Calls in progress cannot be transferred from one base station to another.
12 In Case of Problems
Service Hotline
Should problems arise with the telephone, please refer to the following information first. In the case of technical problems, you can contact our hotline service, Tel. 0900 00 1675 within Switzerland (Swisscom fees at time of going to print: CHF 2.60/min). In the case of claims under the terms of guarantee, please contact your sales outlet. There is a 2 year period of guarantee.
Problems and solutions
Problems
No connection to base station possible
No telephone calls possible
Connection is disturbed or cut off
Solutions
− Check that the handset has been registered on the base station with the correct PIN code;
− The telephone is not connected properly or is defective. Only use the telephone connection cable supplied.
− Test whether the telephone connection is in order by using another telephone.
− The power adaptor plug is not plugged in or there is a complete power failure.
− The rechargeable batteries are empty or defective.
− The handset is too far from the base station.
− The wrong dialling mode is set;
− The handset is too far from the base station.
− The base station is in an unsuitable location.
The system no longer responds
The batteries are empty within a short time
The caller number display (CLIP
3
) does not function
Technical Properties
− Reset all the functions to their default settings;
− Disconnect the power adapter plug briefly from the power socket.
− The batteries are empty or defective.
− Place the handset in the base station properly.
Clean the contact surfaces on the handset and base station with a soft, dry cloth.
− Place the handset in the base station for 14 hours.
− The caller number display (CLIP) is a supplementary service offered by your telephone network provider. Contact your network provider for further information.
− The caller has suppressed the transmission of their phone number.
13 Technical Properties
Technical data
Feature
Standard
Power supply (base station)
Power supply (charging station)
Range
Standby time
Max. talk time
Rechargeable batteries
Dialling mode
Permissible ambient temperature
Permissible relative humidity
Flash function
Value
DECT 1 −GAP 2
Input: 100−240 V AC, 50/60 Hz
Output: 7.5 V, 300 mA
Input: 100−240 V AC, 50/60 Hz
Output: 7.5 V DC, 200 mA
Outdoors: Approx. 300 m
Indoors: Approx. 50 m
Up to 100 h
Up to 10 h
2 x AAA NiMH 1.2 V
Tone dialling mode
Pulse dialling mode
10°C to 30°C
20% to 75%
100 ms, 250 ms, 600 ms
1
DECT : D igital E nhanced C ordless T elecommunication = Standard for cordless telephones.
2 GAP : G eneric A ccess P rofile = Standard for the interoperation of handsets and base stations from different manufacturers.
3
CLIP: C alling L ine I dentification P resentation = Displays the caller’s phone number.
19
20
Maintenance / Guarantee
Declaration of Conformity
This device fulfils the requirements stipulated in the EU directive:
1999/5/EC directive on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. Conformity with the above mentioned directive is confirmed by the CE symbol on the device.
To view the complete Declaration of Conformity, please refer to the free download available on our web site www.switel.com.
14 Maintenance / Guarantee
Maintenance
Clean the housing surfaces with a soft, fluff−free cloth.
Do not use any cleaning agents or solvents.
Guarantee
SWITEL equipment is produced and tested according to the latest production methods. The implementation of carefully chosen materials and highly developed technologies ensure trouble−free functioning and a long service life. The terms of guarantee do not apply where the cause of equipment malfunction is the fault of the telephone network operator or any interposed private branch extension system. The terms of guarantee do not apply to the batteries or power packs used in the products. The period of guarantee is 24 months from the date of purchase.
All deficiencies related to material or manufacturing errors within the period of guarantee will be redressed free of charge. Rights to claims under the terms of guarantee are annulled following tampering by the purchaser or third parties. Damage caused as the result of improper handling or operation, normal wear and tear, incorrect positioning or storage, improper connection or installation or Acts of God and other external influences are excluded from the terms of guarantee. In the case of complaints, we reserve the right to repair defect parts, replace them or replace the entire device. Replaced parts or devices become our property. Rights to compensation in the case of damage are excluded where there is no evidence of intent or gross negligence by the manufacturer.
If your device does show signs of a defect within the period of guarantee, please contact the sales outlet where you purchased the SWITEL device, producing the purchase receipt as evidence. All claims under the terms of guarantee in accordance with this agreement can only be asserted at the sales outlet. No claims under the terms of guarantee can be asserted after a period of two years from the date of purchase and hand−over of the product.
Notes
Notes
21
Declaration of Conformity
21
Diese Anlage entspricht der europäischen R&TTE Richtlinie.
Für die komplette Konformitätserklärung nutzen Sie bitte den kostenlosen Download von unserer Website www.switel.com.
Cet équipement est conforme à la directive européenne R&TTE.
Pour obtenir la déclaration de conformité intégrale, veuillez vous servir du téléchargement gratuit de notre site Internet www.switel.com.
Quest’apparecchiatura è conforme alla direttiva europea R&TTE.
Per la dichiarazione di conformità completa si prega di voler usufruire del servizio gratuito di download dal nostro sito Internet www.switel.com.
This equipment complies with the European R&TTE directive.
To view the complete Declaration of Conformity, please refer to the free download available at our web site: www.switel.com.
Service Hotline
Bei technischen Problemen können Sie sich an unsere Service−Hotline unter Tel. 0900 00
1675 innerhalb der Schweiz (Kosten Swisscom bei Drucklegung: CHF 2.60/min) wenden.
S’il s’agit de problèmes techniques, vous pouvez vous adresser à notre hotline de service en
Suisse en appelant le numéro 0900 00 1675 (frais Swisscom à la date d’impression de ce manuel : CHF 2.60/min).
In caso di problemi tecnici è possibile rivolgersi alla nostra hotline di assistenza tecnica chiamando al numero 0900 00 1675 valido per la Svizzera (spese da rete Swisscom alla data di stampa: CHF 2.60 / min).
In the event of technical problems, you can contact our hotline service, Tel. 0900 00 1675 within Switzerland (cost via Swisscom at time of going to print: CHF 2.60/min).
Version 1.0 − 17.06.2009
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement