American Standard 7075202.002 Colony Pro 4 in. Centerset 2-Handle Low-Arc Bathroom Faucet with 50/50 Pop-Up Assembly in Polished Chrome Installation Guide

American Standard 7075202.002 Colony Pro 4 in. Centerset 2-Handle Low-Arc Bathroom Faucet with 50/50 Pop-Up Assembly in Polished Chrome Installation Guide
INSTALLATION
INSTRUCTIONS
COLONY® PRO
7075.200
7075.202
7075.205
CENTERSET
LAVATORY FAUCET
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
RECOMMENDED TOOLS
Adjustable Wrench
1 INSTALL FAUCET CAUTION
Channel Locks
Plumbers’ Putty or Caulking
Phillips Screwdriver
Hex Wrench (2 mm)
Turn off hot and cold water
supplies before begining.
• Insert FAUCET (1) and POP-UP CABLE (2) through mounting
holes of Sink or Mounting Surface.
1
2 SECURE FAUCET AND MAKE WATER SUPPLY CONNECTIONS
• Secure FAUCET (1) with ATTACHMENT NUTS (2) supplied.
(HAND TIGHTEN).
• Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (3) or 3/8"O.D. BULL-NOSE RISERS (4). Use adjustable
wrench to tighten connections. Do not over tighten. Be careful
not to kink copper supply when bending. Use tubing cutter to
cut to proper length.
2
1
3
COUPLING NUT
4
FERRULE
NOTE: FLEXIBLE SUPPLIES HAVE TO BE PURCHASED SEPARATELY
3 INSTALL POP-UP DRAIN
• Apply a bead of putty to
underside of FLANGE (1).
1
3a
1
• Drop FLANGE (1) into LAVATORY
DRAIN (2). From below assemble
RUBBER GASKET (3), METAL
WASHER (4) and LOCK NUT (5).
Do not tighten.
3
2
4
5
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
-1-
M965761 (8/16)
3b
3c
• Place SEAL (1) with small end facing up into
TAILPIECE (2) and tighten against DRAIN
BODY (4). PIVOT ROD (3) opening in
TAILPIECE (2) should face the rear of the
lavatory. Tighten LOCK NUT (5) with
channel locks. Do not over tighten.
4
• Assemble PIVOT ROD (1), PIVOT NUT (2). CLIP (3) and SEAL (4)
as shown. Hand tighten PIVOT NUT (2) Drop STOPPER (5)
into drain.(For vandal proof drain rotate stopper so PIVOT
ROD (1) goes through EYE (6) of STOPPER (5). Make
connection to “P” TRAP.)
• Remove one end of CLIP (3) from PIVOT ROD (1) by squeezing
ends together while sliding.
• Insert PIVOT ROD (1) into second or third hole in EXTENSION (7)
and reassemble CLIP (3). (EXTENSION (7) may need to be bent).
• Adjust STOPPER (5) height by repositioning EXTENSION (7)
andtightening THUMBSCREW (8).
5
3
8
5
1
7
2
6
1
3
2
4
3 TEST INSTALLED FAUCET
• Remove AERATOR. With handles in OFF position, turn on water supplies and check all connections for leaks.
• Operate both handles to flush water lines thoroughly. Operate LIFT ROD and check DRAIN for leaks. Replace AERATOR.
4 SERVICE
If Faucet Drips Proceed As Follows:
• Turn HANDLES in OFF position.
• If spout drips, operate HANDLES several times from OFF to ON position. Do not forc HANDLES they turn only 90˚.
• AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.
To Change Handle Position:
• Remove INDEX BUTTON (1), HANDLE SCREW (2) and HANDLE (3).
• Remove ADAPTER (4) & RETAINING O-RING (5).
• Lift and turn STOP WASHER (6) 90˚.
• Replace RETAINING O-RING (5)
& ADAPTER (4).
Replace HANDLE (3).
90°
5
6
1
2
3
Aerator
4
90°
-2-
M965761 (8/16)
COLONY® PRO
CENTERSET
LAVATORY FAUCET
MODEL NUMBERS
M970169-YYY0A
SET SCREW &
PLUG BUTTON
HOT/COLD
7075.200
7075.202
7075.205
M970186-YYY0A
LEVER HANDLE KIT
M911107-0070A
ADAPTER
M970182-YYY0A
POP-UP KNOB & ROD
M964492-0070A
VALVE NUT
M913332-0070A
BEARING WASHER
M923840-0070A
AERATOR
M964005-0070A
VALVE
M953450-YYY0A
(7075.200)
POP-UP DRAIN
ASSEMBLY
M953465-YYY0A
(7075.202)
POP-UP DRAIN
ASSEMBLY
065800-0070A
ATTACHMENT NUT
Replace the “YYY” with
appropriate finish code
POLISHED CHROME
002
LEGACY BRONZE
278
SATIN NICKEL
295
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
-3-
M965761 (8/16)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement