EMCO E4STRN36WH 36 in. x 80 in. 400 Series White Universal Traditional Self-Storing Aluminum Storm Door Installation guide
Advertisement
Advertisement
Installation Guide
for EMCO® Woodcore Self-Storing and Self-Storing Colonial and Traditional
Storm Doors with Mortised Handle Set and Retractable Insect Screen
Please Do Not Return Product to Store!
PLEASE call the storm door Solution Center at 1-800-933-3626, with any questions regarding installation, lost part replacement, or anything else related to your storm door purchase.
Read this entire guide before you begin your installation. If your abilities do not match the requirements of this installation, contact an experienced contractor.
PARTS OVERVIEW
Your installation kit should contain the following parts. However, in some door models, not all of the parts will be used.
A
A
B
C
D
E
F
G
H
I
J
K
L
M
Rain Cap
Door Frame
Rain Cap Extender
Ventilating Glass Panel
Hinge Rail with 4 hinges
(Hinge Side Z-bar)
Insect Screen
Latch Rail
(Handle Side Z-bar)
Sweep
Sweep fin
Side Screw Covers (2)
Top Screw Cover (1)
Hinge Rail Shim
Edge Seal
C
E
N
O
P
Q
R
S
Not Shown
Screen Shipping Clip
Installation Kit
(Pink, Clear & Green Parts
Bags Inside)
Window Handle Kit
(If Applicable)
Latch Side Spacer Clip
Sill Spacer Clip
Slot Cover
G
H
J
K
L
M
G
A
Figure 1
F
E
J
D
I
K
H
EMCO Enterprises, Inc., is a wholly owned subsidiary of Andersen Corporation. EMCO manufactures and supports the limited warranties for Andersen® and EMCO® doors.
“Andersen”, “EMCO” and all other marks where denoted are trademarks of Andersen
Corporation. ©2014 Andersen Corporation. All rights reserved.
1
M
B
Andersen SDD, PO Box 853
Des Moines, IA 50306-0853
Rev 1-2014 12088 Print in Color
p/n 504119
U
SAFETY FIRST: Please read and follow all Cautions and Warnings in this guide.
warning
Entry door hardware and handle may become hot when exposed to sunlight.
warning
Improper use of hand or power tools could result in injury and/or product damage. Follow equipment manufacturer’s instructions for safe operation. Always wear safety glasses.
warning
Metal fasteners and other hardware components may corrode when exposed to preservative treated and fire-retardant treated lumber.
Obtain and use the appropriate size stainless steel fasteners and hardware as called out by the installation guide to fasten unit to any rough opening made from pressure treated and fire-retardant treated lumber. Failure to use the appropriate materials for the installation may cause a failure resulting in injury, property or product damage.
warning
Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to lift, carry, and install window and door products to avoid injury and/ or property damage.
warning
The insect screen is intended for reasonable insect control and not the retention of objects or persons within the interior. The insect screen material will not stop a person from falling through the door.
RECOMMENDED TOOLS
Safety Glasses
Phillips
Chisel
Screwdriver
Flat tip
Drill
Hammer
Metal File
Drill Bits
1/2”
3/4”
Pencil
Gloves
Tape
Measure !
Pliers
5/8”
5/8”
!
1
To install the storm door, you must verify that the opening width, height and mounting surface are sufficient.
VERIFY MOUNTING REQUIREMENTS !
!
!
!
5/8”
!
1. Measure the width at the top, middle, and bottom of the opening of the brick mold or exterior trim. Refer to Table 1.
(Figure 2)
5/8” 1/2”
5/8”
2. Measure the height at the center of the opening. Measure from the inside of the brick mold or exterior trim, down to the top of the bottom sill. Refer to Table 1.
1/2”
5/8”
Table 1: Door Sizes
**
5/8” Opening Sizes
W 1 - 3 (width)
*
H (height)
1/2”
1 1/2”
Use this table to determine if your storm door will fit into the opening:
36” x 80” 35 3/4” TO 36 3/8”
5/8”
1”
1 1/2”
33” x 80” 32 3/4” TO 33 3/8”
1 1/2”
32” x 80” 31 3/4” TO 32 3/8”
1 1/2”
3.
1 1/2” the rain cap, hinge rail and latch rail (Figure 3) . You must have a minimum of:
2”
2”
W1
5/8”
W2
5/8”
!
H
1 1/2”
1 1/2”
Scissors !
Center Punch
1/2”
1/2”
1”
3/4” min
1/2”
1/2” min
2 1/2” min
2”
1”
Figure 3
1/2”
!
1/2”
**
• 1” mounting surface depth.
• 3/4” mounting surface front.
*
*
• 2 1/2” handle clearance
1 1/2”
* For opening widths up to 1” wider or for mounting surface depth between 5/8” - 3/4”, please call our Solution Center at 1-800-933-3626 to purchase a special kit to accommodate your situation.
Nominal storm doors sizes are listed. The actual storm door frame width and height will be less.
Example: A nominal size of 36” x 80” may have an actual storm door frame size of 35 1/8” x 79 1/8”.
W3
Figure 2 iNterior view
VISTA InTERIOR vUe De L’iNtÉrieUr
= eXterior view
VISTA EXTERIOR vUe De L’eXtÉrieUr
= i view
X view
2
2”
1/2”
1/2”
1”
1/2”
1/2”
1”
O
L
Tools needed:
2
INSTALLATION
PREPARATION
Installation
Kit a X view
!
i view
LeFt HANDeD
A LA IZQUIERDA
À MAiN GAUCHe riGHt HANDeD
A LA DERECHA
À MAiN Droite
5/8”
5/8”
Figure 6
Figure 4 Figure 5
In this step, you will determine the handle side of your storm door.
1. Left Handed (Figure 4) : From the exterior, a left handed storm door will have the handle on the left side of the storm door. See pages 4-8 for installation instructions.
1 1/2”
2.
Right Handed (Figure 5) : From the exterior, a right handed storm door will have the handle on the right side of the storm door. See pages 9-13 for installation instructions.
3.
The top interior is where the insect screen and cover plate are located (Figure 6) .
1 1/2” c Determine if Hinge Rail Shim is needed
X view
Nominal Storm
Door Sizes
36”x80”
34” x 80”
33” x 80”
32”x80”
Shim needed if opening width is:
36 1/8” TO 36 3/8”
34 1/8” TO 34 3/8”
33 1/8” TO 33 3/8”
32 1/8” TO 32 3/8”
L
L iF reqUireD
SI fUERA nECESARIO si NÉCessAire
Tape x 4
1. Use the table above to determine if you need to use the provided hinge rail shim (L).
2. If your opening width falls within the dimensions listed, you will need to install the shim. If your opening width does not fall within these dimensions, proceed to step 3.
3. Remove any debris from the mounting surface where the hinge rail shim (L) will be attached.
4. Apply the four strips of double stick tape from the pink bag to the shim, spacing them evenly along the entire length. Attach the shim to the mounting surface, as shown.
b !
2 1/2”
1/2”
40 1/2”
1/2”
HASTA EL bATIEnTE DE LA pUERTA jUsqU’AU seUiL De LA porte
1. Most homeowners prefer to have the storm
2” door handle. In shallow door openings, this can cause the two handles to interfere.
Check for potential interference using the rough measurements. If you anticipate that there will be interference, hand the storm door on the opposite side of your entry door. See page 2, Figure 3 for detailed hardware depth requirements.
1/2”
1”
3
3
PREPARE
STORM
DOOR FOR
INSTALLATION
(Left Hand)
E
Q
H
#6
3/4” Machine Pan Painted
1-1/4” SMS Pan
#8
1/2” SMS Pan
1/2” SMS Pan Painted
#6
3/4” Machine Pan Painted
1/2” Self-Drill Pan
1-1/4” SMS Pan
1/2” Self-Drill Pan Painted
#8
7/8” Machine Pan Painted
R
1/2” SMS Pan Painted piNk bAG / bOLSA ROSA / sAC rose
O
1/2”
Painted x 2
1” SMS Pan
1” x 8 a
!
i view b
E
!
!
!
i view c
1/2” view i
5/8”
3/4” Machine Flathead
1/2”
5/8” 1/2” H
1.
2.
3. d
#6
3/4” Machine Pan Painted
1-1/4” SMS Pan the ground. TIP: Lay on door carton.
Identify the top of the hinge rail (E).
#8
!
i
1 1/2” view
!
1/2” SMS Pan Painted
5/8”
5/8” top pARTE SUpERIOR
HAUt
5/8”
1 1/2”
1.
2. e bottoM bAs
1/2”
1/2”
1/2”
#10
#12
#10
2”
1-1/2” Machine Flathead
2”
1 1/2” pERfIL proFiL
1/2”
2” SMS Pan Painted
1” Machine Pan Painted hole from the screws removed in step 3a .
NOTE: Top of hinge rail should extend
1-1/2” Machine Flathead drill 1” deep pilot holes in door frame at each hinge and fasten using 1” unpainted screws from the pink bag in the installation kit.
1/2”
1”
1”
I
1. Slide sweep fin (I) into track in sweep (H).
2.
Install door sweep so it is centered across
5/8” SMS Pan Painted bottoM bAs discard.
width of door frame and pressed tight against bottom of door frame.
3. Center punch and then predrill 1/8” pilot holes at the bottom of the slot for future adjustment, then attach the sweep using painted 1/2” screws from the pink bag.
1”
S i view
2”
1/8” 2” SMS Pan Painted
H O
#12
5/8” SMS Pan Painted top pARTE SUpERIOR
HAUt
R
7/8” Machine Pan Painted
Kit
1” SMS Pan
1. Install the sill spacer clip (R) under the latch side sweep screw and tight against the bottom of the sweep. Tighten the sweep
1. Find the Installation Kit (O) located inside the door carton and identify the slot cover (S), the color matched 1/2” flat head screws, and the 1/8” drill bit found in the pink bag.
2. Do not remove the insert located inside of the hinge side pocket.
2.
Install the latch side spacer clip (Q) over the
3. Hold the slot cover over the hinge side pocket of the door frame edge. Make sure hinge side pocket is fully covered by cover plate. Mark the two mounting screw locations.
latch side of the door frame as shown. This
4. Using a drill and 1/8” drill bit, drill a hole in the marked locations. Install the slot cover with the
1” Machine Pan Painted two 1/2” painted flat head screws.
1-1/2” Machine Flathead
4
#10
1-1/2” Machine Flathead
2” SMS Pan Painted
#12
5/8” SMS Pan Painted
a
4
INSTALL
HINGED
STORM DOOR
IN OPENING
(Left Hand)
A
R
X view b
C
#6
3/4” Machine Pan Painted
1-1/4” SMS Pan
#8
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
!
5/8”
5/8”
1/2” 7/8” Machine Pan Painted
1/2”
1 1/2” 1” SMS Pan
1 1/2”
2”
1/8”
1”
O
YeLLow bAG / bOLSA AmARILLA / sAC jAUNe
1” x 19
3/16” Plug x 1
1” SMS Pan Painted
1” Machine Pan Painted
#10
Q
!
view !
c X view
1/2”
1/2”
1. Set the door frame on the entry sill so the hinge rail is tight against the mounting surface (or hinge rail shim) and the sill spacer clip (R) is sitting on the door sill.
2.
Tip the top of the door frame into the opening, making sure that the sill spacer clip is still on the door frame and resting on the sill.
NOTE: Door may be out of square at this time.
1. #12
1 1/2”
5/8” SMS Pan Painted latch side spacer clip hole is not completely filled, review step 2c.
2.
Pre-drill pilot holes using drill bit, then use 1”
1. Open the storm door.
2.
Pre-drill and fasten the hinge rail to the door
2”
3. Remove both orange clips from the bottom of the door frame and properly discard.
1/2”
1” d X view e X view
3/16” pLUG
TApòn DE 0.31 Cm boUCHoN peiNt 4,8 MM
A
A
C
A
1. Open the storm door. Place the rain cap (A) in the opening so that it rests on top of the hinge rail, aligning the end of the the rain cap with the edge of the hinge rail.
2. Close the storm door. Adjust rain cap to achieve an even gap between the top of the door frame.
3. Look at the center hole of the rain cap. If the mounting surface can be seen in the entire hole, proceed to step 4e . If the mounting surface cannot be seen in the entire hole, or if there is space above the rain cap, then remove the rain cap.
4.
From the mounting surface (back) side of the rain cap, completely insert a 3/16” plug from the yellow bag into the middle hole.
5. Re-install the rain cap as described above.
5
1. Using the drill bit and 1” screws from the yellow bag, fasten the rain cap to the mounting surface.
2.
If a plug was installed in the middle hole, you will need to install the rain cap extender (C).
3.
Place the rain cap extender over the rain cap as shown, with both ends being flush.
4. Using the drill bit and 1” screws from the yellow bag in the installation kit, fasten the rain cap extender to the mounting surface.
a
5
INSTALL
LATCH RAIL
(Left Hand) pAD
ALmOHADILLA tAMpoN
G
#6
3/4” Machine Pan Painted
1-1/4” SMS Pan
#8
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
!
5/8”
5/8”
1 1/2”
1 1/2”
7/8” Machine Pan Painted
1/2”
2” 1” SMS Pan
1/8”
1”
O
YeLLow bAG / bOLSA AmARILLA / sAC jAUNe
1” x 6
Pad x 3
1” SMS Pan Painted view
X
!
b
1-1/2” Machine Flathead
#10
1-1/2” Machine Flathead
G
!
X view
1/2” a
1.
2” SMS Pan Painted
Find the three 1/2” square adhesive backed spacer pads in the yellow bag in the installation kit.
2. Swing door open and wipe off any residue on edge of door.
3. Peel the paper backer off each pad and attach them to the latch side
#12 another close to the center of the door, and the third approximately 6” up from the bottom.
1.
2.
Close storm door and slide latch rail towards door frame until it contacts all three spacer pads, creating a 3/16” gap.
3.
4.
Place latch rail (G) in the opening with top end pushed up against rain cap. mounting surface.
Open storm door and remove spacer pads, then properly discard.
1/2”
Using drill bit and 1” screws from the yellow bag, fasten latch rail to
5/8” SMS Pan Painted
1”
6
INSTALL THE
WINDOW
HANDLE
(Left Hand)
P
Window
Handle
1 1/2” i view b i view c i view tAb pESTAñA
LANGUette
2-3
1
1. Lower or raise the ventilating glass panel so that the holes below the insect screen are at a comfortable working height.
2.
If applicable, refer to the instructions included in the Window Handle Kit (P) to install the window handle.
If installing a door without a window handle:
1.
Lower insect screen by pulling down on orange insect screen helper tab. Once screen is exposed, grab and hold in hand.
2. Remove helper tab by twisting and pushing it outwards.
6
CUt-AwAY view
VISTA TRAnSVERSAL vUe eN CoUpe FroNtALe
1. When you reach top of ventilating glass panel, a slight pull towards you will allow insect screen pull lip to maneuver around ventilating glass panel rail.
2.
A slight push away from you will align lip and rail.
3. Raise insect screen lightly. Screen will be fully engaged when ventilating glass panel rail is interlocked with insect screen lip.
a
7
INSTALL
HANDLE
SET &
CLOSER
(Left Hand) a
8
IF #6
(Left Hand)
Tools needed:
3/4” Machine Pan Painted
1-1/4” SMS Pan
9
#8
1/2” SMS Pan i view a
FILE EDGE
SEAL
(Left Hand)
M 1/2” SMS Pan Painted
Tools needed:
X view a
Installation
Kit
1. Refer to the instructions included in the
Installation Kit (O) to drill the handle holes and to install the door handles and closer.
10
O
INSTALL EDGE
SEAL
(Left Hand)
M
5/8”
5/8”
!
1 1/2” bottoM
1/2” SMS Flathead
warning pARTE InfERIOR bAs
1/2” Self-Drill Pan
H
Generously round the bottom corner of the edge seal with a metal file to avoid sharp edges. Failure to round the bottom corners may cause an injury.
1/2” Self-Drill Pan Painted
1. Close the storm door.
1.
File the bottom corners of the edge seal (M) until they are smooth.
2. From the interior, loosen the sweep screws
3/4” Machine Flathead lightly comes into contact with the door sill.
3.
Retighten the sweep screws.
7/8” Machine Pan Painted
!
view
X
1 1/2” b
1/2”
2”
1/2”
1/2”
1” SMS Pan Painted
1”
1/8”
1” Machine Pan Painted !
X view
!
c
O
YeLLow bAG / bOLSA AmARILLA / sAC jAUNe
1”
X view M x 6
#10
1/2”
1. Open the door and remove all four hex head screws from the edge of the door, then properly discard screws.
1/2”
1/2”
M
M #12
1. Align first hole down on edge seal with top
5/8” SMS Pan Painted screw from yellow bag.
2”
1. Pre-drill 1” deep pilot holes in door frame through pre-drilled holes in edge seal.
2. Fasten edge seal to door frame using five 1” painted screws from yellow bag.
1”
7 1 1/2”
11
INSTALL
SCREW
COVERS
(Left Hand) a
!
sHort LeG pESTAñA CORTA rAiNUre CoUrte
!
K
X view
J
K
Tools needed:
K
5/8” 1/2”
5/8” 1/2” 1/2”
1. Lock leg of screw cover (K) into short leg of rain cap screw track. Press on other leg to snap it into long leg of track. Make sure screw cover snaps into screw track along the entire length of the rain cap.
2. Repeat this process with remaining side screw covers.
3.
Using scissors, trim off any excess that may remain.
1”
1 1/2”
8
12
PREPARE
STORM
DOOR FOR
INSTALLATION
(Right Hand)
E
Q
H
#6
3/4” Machine Pan Painted
1-1/4” SMS Pan
#8
1/2” SMS Pan
1/2” SMS Pan Painted
#6
3/4” Machine Pan Painted
1/2” Self-Drill Pan
1-1/4” SMS Pan
1/2” Self-Drill Pan Painted
#8
7/8” Machine Pan Painted
R
1/2” SMS Pan Painted
1” SMS Pan piNk bAG / bOLSA ROSA / sAC rose
O
1/2”
Painted x 2
1” x 8 a
!
i view b
E
!
!
!
i view c
1/2” view i
5/8”
3/4” Machine Flathead
5/8” 1/2” 1/2” top pARTE SUpERIOR
HAUt
5/8”
H
I
1.
2.
3. Remove the two middle hex head screws from the hinge side edge of door frame.
d
#6
1-1/4” SMS Pan the ground. TIP: Lay on door carton.
Identify the top of the hinge rail (E).
#8
5/8”
5/8”
!
5/8”
1 1/2” the hinge rail should extend approximately
3/16” beyond the top of the door frame.
2.
Pre-drill 1” deep pilot holes in door frame at
1/2” SMS Pan Painted i
1 1/2” view
!
1. e pERfIL proFiL
1/2” up with the bottom hole from the screws removed in step 12a . NOTE: The the top of
1-1/2” Machine Flathead each hinge and fasten using 1” unpainted screws from the pink bag in the installation kit.
1/2”
1/2”
1-1/2” Machine Flathead
2”
1” SMS Pan Painted
2” SMS Pan Painted
1/2”
1 1/2”
1” SMS Pan
1. Slide sweep fin (I) into track in sweep (H). Crimp
1” Machine Pan Painted
#12 bottoM pARTE InfERIOR bAs
#10
2”
1/2”
1” bottoM bAs of door frame.
1”
2. Install door sweep so it is centered across width of door frame and pressed tight against bottom
3. Center punch and then predrill 1/8” pilot holes at the bottom of the slot for future adjustment, then attach the sweep using painted 1/2” screws from the pink bag.
view i
1”
S
2”
1/8” 2” SMS Pan Painted
Q
H
3/4” Machine Flathead
O
#12 top
5/8” SMS Pan Painted
HAUt
Installation
Kit
1.
1” SMS Pan side sweep screw and tight against the bottom of the sweep. Tighten the sweep
1. Find the Installation Kit (O) located inside the door carton and identify the slot cover (S), the color matched 1/2” flat head screws, and the 1/8” drill bit found in the pink bag.
2. Do not remove the insert located inside of the hinge side pocket.
2.
Install the latch side spacer clip (Q) over the latch side of the door frame as shown. This
3. Hold the slot cover over the hinge side pocket of the door frame edge. Make sure hinge side pocket is fully covered by cover plate. Mark the two mounting screw locations.
4. Using a drill and 1/8” drill bit, drill a hole in the marked locations. Install the slot cover with the
1” Machine Pan Painted two 1/2” painted flat head screws.
1-1/2” Machine Flathead
9
#10
1-1/2” Machine Flathead
2” SMS Pan Painted
#12
5/8” SMS Pan Painted
a
13
INSTALL
HINGED
STORM DOOR
IN OPENING
(Right Hand)
A
X view
R b
C
#6
3/4” Machine Pan Painted
1-1/4” SMS Pan
#8
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
!
5/8”
5/8”
1/2” 7/8” Machine Pan Painted
1/2”
1 1/2” 1” SMS Pan
1 1/2”
2”
1/8”
1”
YeLLow bAG / bOLSA AmARILLA / sAC jAUNe
O
1” x 19
3/16” Plug x 1
1” SMS Pan Painted
!
#10
5/8”
Q
1-1/2” Machine Flathead c c
!
view
X
1/2”
1/2”
1. Set the door frame on the entry sill so the hinge rail is tight against the mounting surface (or hinge rail shim) and the sill spacer clip (R) is sitting on the door sill.
2.
Tip the top of the door frame into the opening, making sure that the sill spacer clip is still on the door frame and resting on the sill.
NOTE: Door may be out of square at this time.
1. #12
1 1/2”
5/8” SMS Pan Painted latch side spacer clip hole is not completely filled, review step 2c.
2.
Pre-drill pilot holes using drill bit, then use 1”
1. Open the storm door.
2.
Pre-drill and fasten the hinge rail to the door
2”
3. Remove both orange clips from the bottom of the door frame and properly discard.
1/2”
1” d X view e X view
3/16” pLUG
TApòn DE 0.31 Cm boUCHoN peiNt 4,8 MM
A
C
A
A
1. Open the storm door. Place the rain cap (A) in the opening so that it rests on top of the hinge rail, aligning the end of the the rain cap with the edge of the hinge rail.
2. Close the storm door. Adjust rain cap to achieve an even gap between the top of the door frame.
3. Look at the center hole of the rain cap. If the mounting surface can be seen in the entire hole, proceed to step 13e . If mounting surface cannot be seen in the entire hole, or if there is space above the rain cap, then remove the rain cap.
4.
From the mounting surface (back) side of the rain cap, completely insert a 3/16” plug from the yellow bag into the middle hole.
5.
Re-install the rain cap as described above.
10
1. Using the drill bit and 1” screws from the yellow bag, fasten the rain cap to the mounting surface.
2. If a plug was installed in the middle hole, you will need to install the rain cap extender (C).
3.
Place the rain cap extender over the rain cap as shown, with both ends being flush.
4.
Using the drill bit and 1” screws from the yellow bag in the installation kit, fasten the rain cap extender to the mounting surface.
a
14
INSTALL LATCH
RAIL
(Right Hand)
G pAD
ALmOHADILLA tAMpoN
#6
3/4” Machine Pan Painted
1-1/4” SMS Pan
#8
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
!
5/8”
5/8” 1/2”
1”
1 1/2” 2” 1” SMS Pan
1/8”
1 1/2”
1” SMS Pan Painted
!
X view !
#10
O
YeLLow bAG / bOLSA AmARILLA / sAC jAUNe
1” x 6
Pad x 3
X view
G
1/2” a
1.
3.
2” SMS Pan Painted
Find the three 1/2” square adhesive backed spacer pads in the yellow bag in the installation kit.
2. Swing door open and wipe off any residue on edge of door.
#12 another close to the center of the door, and the third approximately 6” up from the bottom.
1.
2.
Close storm door and slide latch rail towards door frame until it contacts all three spacer pads, creating a 3/16” gap.
3.
4.
Place latch rail (G) in the opening with top end pushed up against rain cap. mounting surface.
Open storm door and remove spacer pads, then properly discard.
1/2”
Using drill bit and 1” screws from the yellow bag, fasten latch rail to
5/8” SMS Pan Painted
1”
15
INSTALL THE
WINDOW
HANDLE
(Right Hand)
P
Window
Handle
1 1/2” i view b i view c i view tAb pESTAñA
LANGUette
2-3
1
1. Lower or raise the ventilating glass panel so that the holes below the insect screen are at a comfortable working height.
2.
If applicable, refer to the instructions included in the Window Handle Kit (P) to install the window handle.
If installing a door without a window handle:
1.
Lower insect screen by pulling down on orange insect screen helper tab. Once screen is exposed, grab and hold in hand.
2. Remove helper tab by twisting and pushing it outwards.
11
CUt-AwAY view
VISTA TRAnSVERSAL vUe eN CoUpe FroNtALe
1. When you reach top of ventilating glass panel, a slight pull towards you will allow insect screen pull lip to maneuver around ventilating glass panel rail.
2.
A slight push away from you will align lip and rail.
3. Raise insect screen lightly. Screen will be fully engaged when ventilating glass panel rail is interlocked with insect screen lip.
a
16
INSTALL
HANDLE SET
AND CLOSER
(Right Hand) a
17
IF #6
(Right Hand)
Tools needed:
3/4” Machine Pan Painted
1-1/4” SMS Pan
18
FILE EDGE
SEAL
(Right Hand)
Tools needed:
#8
1/2” SMS Pan view i a X view
M 1/2” SMS Pan Painted
Installation
Kit
1.
Refer to the instructions included in the
Installation Kit (O) to drill the handle holes and to install the door handles and closer.
a
O
19
INSTALL EDGE
SEAL
(Right Hand)
M
5/8”
5/8”
!
1 1/2” view
X
1 1/2” bottoM
1/2” SMS Flathead
warning pARTE InfERIOR bAs 1/2” Self-Drill Pan
H
Generously round the bottom corner of the edge seal with a metal file to avoid sharp edges. Failure to round the bottom corners may cause an injury.
1/2” Self-Drill Pan Painted
1.
Close the storm door.
1. File the bottom corners of the edge seal (M) until they are smooth.
2. From the interior, loosen the sweep screws
3/4” Machine Flathead lightly comes into contact with the door sill.
3. Retighten the sweep screws.
7/8” Machine Pan Painted
!
b
1/2”
2”
1/2”
1/2”
1” SMS Pan Painted
1”
1/8”
1” Machine Pan Painted !
X view
!
c
O
YeLLow bAG / bOLSA AmARILLA / sAC jAUNe
1”
M
X view x 6
#10
1/2”
1.
Open the door and remove all four hex head screws from the edge of the door, then properly discard screws.
1/2” 1/2”
M
M #12
1.
Align first hole down on edge seal with top
5/8” SMS Pan Painted screw from yellow bag.
2”
1. Pre-drill 1” deep pilot holes in door frame through pre-drilled holes in edge seal.
2.
Fasten edge seal to door frame using five 1” painted screws from yellow bag.
1”
1 1/2”
12
20
INSTALL
SCREW
COVERS
(Right Hand)
J
K
Tools needed:
!
a
K
!
X view sHort LeG pESTAñA CORTA rAiNUre CoUrte
K
5/8” 1/2”
5/8” 1/2” 1/2”
1. Lock leg of screw cover (K) into short leg of rain cap screw track. Press on other leg to snap it into long leg of track. Make sure screw cover snaps into screw track along the entire length of the rain cap.
2. Repeat this process with remaining side screw covers.
3.
Using scissors, trim off any excess that may remain.
1”
1 1/2”
13
CLEANING INSTRUCTIONS wiNDow GLAss – the glass may be cleaned with any household glass cleaner. keep glass cleaners away from painted parts and brass/nickel components.
pLAstiC pArts – plastic door components may be cleaned using a mild soap and water mixture and by gently rubbing the affected area. Do not use harsh abrasives or any product that contains chlorine.
ALUMiNUM pArts – Aluminum parts on the door may be cleaned using a mild soap and water mixture and by gently rubbing the affected area. Mineral spirits may be used and will not harm the paint. this will remove many items such as glue residue. Do not use harsh abrasives or any product that contains chlorine.
LIMITED WARRANTIES proDUCt LiMiteD wArrANtY
Door FrAMe: eMCo enterprises, inc. (eMCo) warrants the door frame, hinges, and painted finish on eMCo® storm door products to be free from defects in manufacturing, materials, paint adhesion, or workmanship, under normal use, for ten (10) years or as long as the original consumer purchaser owns the home in which the door was initially installed, whichever is shorter.
CoMpoNeNts: eMCo warrants the non-glass and non-insect screen fabric components of eMCo® storm doors (including brass and nickel hardware finish and the mechanical functions of locksets, closers, windows and insect screens) to be free from defects in manufacturing, materials and workmanship for a period of one (1) year from the date of original retail purchase or for as long as the original consumer purchaser owns the home in which the door was initially installed, whichever is shorter. kick panel retention within the frame is not covered under this warranty.
in the event a door frame, hinges, insulated glass or a component fails as a result of a defect in manufacturing, materials or workmanship within the limited warranty period specified above, and upon written proof of purchase, eMCo, at its option, will provide a replacement door frame, hinge, and/or components without charge – installation is not included. such replacement or repair is warranted for the remainder of the original limited warranty period. please locate the door serial number and written proof of purchase and contact eMCo Consumer support at 1-800-933-3626.
“oops-prooF” iNstALLAtioN LiMiteD wArrANtY eMCo enterprises, inc. (eMCo) warrants that any part lost or mis-cut during the original installation of your eMCo storm door will be repaired or replaced at no additional charge within ninety (90) days of the date of original purchase. this limited warranty will not apply if the part has been misused, abused or altered. Cutting parts not specified by the installation guide or mis-drilled parts are not included in this warranty.
in the event a part is lost or mis-cut within the limited warranty period, eMCo, at its option, will provide the appropriate replacement part – installation is not included. please locate the door serial number and written proof of purchase and contact eMCo Consumer support at 1-800-933-3626.
GeNerAL LiMiteD wArrANtY iNForMAtioN the limited warranties set forth in this document are the only express warranties (whether written or oral) applicable to eMCo® storm doors, and no one is authorized to modify or expand these limited warranties. All warranty claims must be made during the applicable warranty periods.
ALL iMpLieD wArrANties iNCLUDiNG MerCHANtAbiLitY AND FitNess For A pArtiCULAr pUrpose Are LiMiteD to tHe AppLiCAbLe stAtUte oF
LiMitAtioN, bUt iN No CAse wiLL tHeY eXteND beYoND tHe terM oF tHe LiMiteD wArrANties set FortH Above. eMCo eXCLUDes AND wiLL
Not pAY For iNCiDeNtAL or CoNseqUeNtiAL DAMAGes, wHetHer ArisiNG oUt oF CoNtrACt, tort or otHerwise, AND its LiAbiLitY wiLL iN ALL iNstANCes be LiMiteD to tHe repAir or repLACeMeNt oF tHe DeFeCtive proDUCt.
some states do not allow the exclusion of incidental and consequential damages, or limitation of the duration of an implied warranty, so the above limitations or exclusions may not apply to you.
this limited warranty gives you specific legal rights, and you may also have other rights that may vary from state to state and in Canada.
what is Not covered by this limited warranty: Damage caused by 1) improper installation, maintenance, or use 2) chemicals or airborne pollutants, such as salt or acid rain; 3) acts of God, including wind damage; 4) products not manufactured by eMCo eMCo enterprises, inc. is a wholly owned subsidiary of Andersen Corporation. eMCo manufactures Andersen® and eMCo® storm doors. eMCo supports the limited warranties covering Andersen® storm and screen Doors. “Andersen”, “eMCo” and all other marks where denoted are trademarks of Andersen Corporation. ©2013 Andersen Corporation. All rights reserved.
Reprinted and effective as of May, 2011.
On-line Parts and Knowledge Store
Andersen is committed to helping you find parts quickly and easily for your Andersen® or eMCo® storm door. Use the site below and your serial number to find many of the most-common replacement parts for your storm door.
this site also includes the Andersen storm Door Learning Center. whether you are trying to find other Andersen® or eMCo® products or you are looking for replacement part installation guides, or other care and maintenance topics and tips, this is a great place to start.
parts.andersenstormdoors.com
14
Public link updated
The public link to your chat has been updated.
Advertisement