TECHNICAL DATA ROC-109 CONCRETE & GARAGE ® FLOOR PAINT + PRIMER DESCRIPTION AND USES . .PRODUCT APPLICATION (cont.) ® . Rust-Oleum Concrete and Garage Floor Paint and Primer is a ready-to-use interior/exterior concrete floor paint designed for use on garages, carports, driveways, basements, porches, patios, walkways, and pool decks A single coat of this self-priming concrete floor paint saves time and resists damage from hot tires, motor oil, grease and gasoline. The durable, UV and weather resistant satin finish is easy to maintain and resists fading and peeling. It is environmentally friendly and can be easily cleaned with soap and water. SURFACE PREPARATION (cont.) Not recommended for use on asphalt or wood surfaces. WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800424-LEAD or log on to www.epa.gov/lead. . FEATURES Wash the entire floor with Rust-Oleum heavy-Duty Degreaser (diluted as stated on the label) or Rust-Oleum Cleaner & Degreaser and scrub the surface using a stiff bristle brush or broom. Spot etch all exposed concrete surfaces using Rust-Oleum concrete Etch or Rust-Oleum Clean & Etch. Rinse thoroughly and allow to dry completely. . Advanced acrylic formula Hot tire and chemical resistant UV and weather resistant Interior/exterior durability .PRODUCTS SKU 225359 225380 225381 319550 320173 320172 320174 320175 . Description Armor Gray Satin – 1-Gallon Battleship Gray Satin – 1-Gallon Satin Tint Base - 1-Gallon Satin Deep Tint Base – 1-Gallon Armor Gray Satin – 5-Gallon Battleship Gray Satin– 5-Gallon Satin Tint Base – 5-Gallon Satin Deep Tint Base – 5-Gallon . APPEARANCE APPLICATION Rust-Oleum concrete and Garage Floor Paint and Primer is ready to use. Do not thin. Apply only when air, material, and surface temperatures are between 50-90°F (10-32°C) and the relative humidity is below 85%. Do not paint outdoors if rain is expected within 48 hours. If using more than one gallon, intermix (box) all cans of the same product to ensure gloss uniformity. Stir thoroughly before applying. NOTE: Painted floors may be slippery when wet. If desired, Rust-Oleum Anti-Skid Additive (sold separately) may be added to the mixed coating. . Dries to a satin finish. .PRODUCT APPLICATION Use a brush or edger to trim the perimeter and hard-to-reach areas. Use a long handled extension pole and a high quality ⅜” nap roller cover to apply an even coat of Rust-Oleum Concrete Garage and Floor Paint and Primer onto the surface. Apply in 4’x4’ foot sections and maintain a wet edge to prevent lap marks and gloss differences. Continue applying in 4’x4’ sections until complete. Only one coat is necessary. If a second coat is desired, wait 24 hours before applying the second coat in a direction perpendicular to the first. Occasional touch-up may be necessary for areas subject to heavy vehicle traffic. Rust-Oleum Decorative Color Chips (sold separately) can be added for an upgraded appearance. Chips should be applied in 4’x4’ sections while the coating is wet. . READ ALL INSTRUCTIONS CAREFULLY BEFORE STARITNG PROJECT SURFACE PREPARATION Bare Concrete Surfaces: Proper surface preparation is critical to performance. Allow new concrete to cure for a minimum of 28 days. Before coating bare concrete surfaces, remove grease, oil, salt and other contaminants with Rust-Oleum Heavy-Duty Degreaser (sold separately) or Rust-Oleum Cleaner & Degreaser (sold separately). Scrub spots thoroughly with a stiff bristle brush or broom and wipe up excess cleaner with rags or paper towels to keep contaminants from spreading. Rinse thoroughly with fresh water. Repeat as necessary to completely clean. DRY TIME Surfaces should be ready for light foot traffic in 12-16 hours and normal foot traffic in 24 hours. FOR FULL CURE AND VEHICLE TRAFFIC, ALLOW 5 DAYS. Dry times increase at cooler temperatures. If necessary, use a wire brush or sander to remove any loose or unsound concrete or masonry. For proper penetration and maximum adhesion, use Rust-Oleum Clean & etch (sold separately). Follow label instructions carefully and allow the floor to dry completely. Wipe your fingers over the clean, dry surface. If you see and dust or powder on your fingers, repeat scrubbing and rinsing until the floor is clean. COVERAGE Each gallon contains enough material to cover approximately 300400 square feet over smooth, bare concrete. Very rough or porous surfaces will require more material. CLEAN-UP Previously Painted, Stained or Sealed Concrete Surfaces: Use a wire brush to remove any loose or peeling paint, stain or sealer. To ensure proper adhesion, scuff sand the entire surface and clean with a solvent such as acetone. Rinse or sweep away dust and other particles. Wash tools and equipment with warm water and a mild detergent immediately after use. Properly dispose of all roller covers and soiled rags and protect unused product from freezing. 1 Form: GDH-1355 Rev.: 051517 TECHNICAL DATA CONCRETE & GARAGE FLOOR PAINT + PRIMER . PHYSICAL PROPERTIES . CONCRETE & GARAGE FLOOR PAINT + PRIMER Resin Type Modified Acrylic Polymer Pigments Varies with color Solvents Propylene Glycol, Water Weight Solids Per Gallon 9.9-10.5 lbs. Per Liter 1.19-1.25 kg By Weight 42.6-45.6% By Volume 32.6-32.8% Volatile Organic Compounds <50 g/l (2.08 lbs./gal.) Recommended Dry Film Thickness (DFT) Per Coat 1.0-1.5 mils (25-37.5µ) for non-porous or smooth concrete 2.0-2.5 mils (50-62.5µ) for porous or profiled concrete Wet Film to Achieve DFT (Unthinned Material) 3.0-4.5 mils (75-112.5µ) for non-porous or smooth concrete 6.0-7.0 mils (150-175µ) for porous or profiled concrete Practical Coverage at Recommended DFT (assumes 15% material loss) Light Foot Traffic Dry Times at 70-80°F (21-27ºC) and 50% Relative Humidity Foot Traffic 300-400 sq.ft./gal. for non-porous or smooth concrete 180-220 sq.ft./gal. for porous or profiled concrete 12-16 hours 24 hours Vehicle Traffic Shelf Life 5 days 5 years Flash Point >200°F (93°C) Safety Information For additional information, see SDS The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice. Rust-Oleum Corporation 11 Hawthorn Parkway Vernon Hills, Illinois 60061 An RPM Company Phone: 877•385•8155 www.rustoleum.com Form: GDH-1355 Rev.: 051517
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021