Schluter KB506252440 Kerdi-Board 2 in. x 24-1/2 in. x 96 in. Building Panel Use and Care Manual

SCHLUTER

®

-KERDI-BOARD

S U B S T R A T E

S U B S T R A T E , B U I L D I N G P A N E L , B O N D E D W A T E R P R O O F I N G

Application and Function

12.1 Schluter ®

-KERDI-BOARD

12.1 Schluter ® -KERDI-BOARD is a multifunctional tile substrate and building panel, which can also be used for creating bonded waterproofing assemblies with tile coverings.

It consists of an extruded polystyrene foam panel, with a special reinforcement material on both sides and fleece webbing for effective anchoring in thin-set mortar.

With the available panel thicknesses of

3/16", 3/8", 1/2", 5/8", 3/4", 1", 1-1/2", and 2" (5, 9, 12.5, 15, 19, 25, 38, and 50 mm) , KERDI-BOARD covers a broad range of application areas for creating flat, level, plumb, square, and dimensionally stable substrates for the installation of ceramic and natural stone tiles. With suitable preparation of the abutting seams and joint areas, the panel may be used for bonded waterproofing assemblies.

KERDI-BOARD is suitable for: creating tile substrates on masonry walls, wood or metal framing, and other finished wall surfaces; creating straight or curved partition walls; creating straight or curved bathtub and shower surrounds; concealing pipes and columns; as well as creating bathtub platforms, vanities, storage shelves, countertops, and various other bathroom structures.

The boards are simply cut to size with a utility knife. The gridlines, which are printed on the surface, are helpful for neat and quick cuts and installation.

KERDI-BOARD can be fully adhered in wall areas or spot-bonded with thin-set mortar. If necessary, the material may be secured with additional wall anchors. In the case of stud framing, KERDI-BOARD is attached with screws and washers from the matching hardware system.

Tiles can be installed directly over

KERDI-BOARD using the thin-set method.

L-shaped and U-shaped KERDI-BOARD panels are available for creating pipe and column coverings, and grooved panels are available for creating curved elements.

Schluter-Systems also offers profiles and attachment hardware for wall connections and finishing edges, as well as matching wall anchors and screws.

12.1 Schluter ® -KERDI-BOARD-SB/-

SC are prefabricated substrates, made of

Schluter ® -KERDI-BOARD, which integrate with the Schluter ® -Shower System. The substrates are waterproof and ready for tile, leaving only sealing of joints and corners to complete waterproofing. The KERDI-

BOARD-SB shower bench is available in triangular and rectangular configurations in the followings sizes (width x depth x height).

The triangular benches are 16" x 16" x 20"

(41 x 41 x 51 cm) and 24" x 24" x 20"

(61 x 61 x 51 cm) . Rectangular benches are

38" x 16" x 20" (97 x 41 x 51 cm) and 48" x 11-1/2" x 20" (122 x 29 x 51 cm) . The

KERDI-BOARD-SC shower curb can be used in conjunction with any shower base.

Curb dimensions are 38" x 6" x 4-1/2"

(97 x 15 x 11.5 cm) and 48" x 6" x 4-1/2"

(122 x 15 x 11.5 cm).

Schluter ® -KERDI-BOARD

Schluter

®

-KERDI-BOARD-SN is a prefabricated shower niche made of

KERDI-BOARD that can be installed in both

Schluter ® -KERDI and KERDI-BOARD wall assemblies. The shower niche features a

1/2" (12.5 mm) -thick by 2" (50 mm) -wide integrated bonding flange and is available in 12" x 6" (30 cm x 15 cm) , 12" x 12"

(30 cm x 30 cm) , 12" x 20" (30 cm x 51 cm) , and 12" x 28" (30 cm or 71 cm) sizes.

Material Properties and

Areas of Application

12.1 Schluter

®

-KERDI-BOARD

Property

Water vapor permeance

Thermal resistance (R-value)

Service temperature range

Flame spread/smoke developed

Thermal barrier evaluation

Method

ASTM E96 1

ASTM C518

ASTM E84

CAN/ULC S102.2

NFPA 286

Value

0.36 perms - 1/2" (12.5 mm)

R 9.1 – 2" (50 mm)

R 2.2 – 1/2" (12.5 mm)

R 0.9 – 3/16" (5 mm)

-58 ° F to 158 ° F (-50 ° C to 70 ° C)

Pass 2

Pass 3

Pass 2,4

1

Using the desiccant method at 100°F (38°C) and 90% RH

2

Per International Building Code Requirements, contact Schluter

®

-Systems for more information

3 Specific building categories, contact Schluter ® -Systems for more information

4 Porcelain tile used as thermal barrier over 1/2" (12.5 mm) -thick KERDI-BOARD on wood framing

KERDI-BOARD is made from extruded polystyrene foam, with a cement-free reinforcement layer laminated to both sides and an anchoring fleece webbing. The surface of the board has gridlines consisting of 3/8" x 3/8" (10 mm x 10 mm) squares printed on one side.

KERDI-BOARD is waterproof and vaporretardant and can withstand all chemical stresses that typically occur in conjunction with ceramic tile coverings. KERDI-BOARD may be used in bonded waterproofing assemblies where required.

KERDI-BOARD is completely flat and will not warp, even with one-sided exposure to temperature and moisture fluctuations. It will not rot or decay.

KERDI-BOARD can be used in a multitude of interior applications. In special cases, the suitability of the material must be verified based on the anticipated chemical and mechanical stresses. The information provided below is intended as general guidelines.

Structures on which KERDI-BOARD is to be installed must be stable and meet any other project-specific requirements.

Select a suitable material thickness if using

KERDI-BOARD for the construction of freestanding partition walls, shelving, or similar structures, and use reinforcement profiles as necessary. Arrange supports made of

KERDI-BOARD at regular intervals consistent with conventional building practices.

Select the material thickness and installation method depending on the evenness of the substrate. KERDI-BOARD can be spot-bonded to walls to correct substrate variations or fully embedded in thin-set mortar where walls are sufficiently even and plumb.

KERDI-BOARD should be stored flat. In case

2 of outdoor storage, protect the material from direct sunlight and weather exposure.

Installation

Fully embedded KERDI-BOARD

Any board thickness suitable

1. Remove all surface contaminants from the substrate that may weaken the bond.

2. Apply thin-set mortar to the substrate and/or onto KERDI-BOARD with a notched trowel. The mortar must bond to the substrate and mechanically anchor the fleece on the KERDI-BOARD surface.

3. Apply the panels to the wall and firmly press them in place to ensure full coverage.

4. Tightly abut the individual panels and align them appropriately.

5. The tiles can be installed immediately using unmodified thin-set mortar.

Choose a notched trowel to match the tile format, and back-butter the tiles, if necessary, to attain full coverage.

Note: If the bond between the thin-set mortar and substrate is questionable, additional mechanical attachment with the KERDI-BOARD-ZSD anchors or KERDI-BOARD-ZT washers and corresponding screws is required.

Fasteners are installed after the thin-set mortar has hardened.

Minimum board thickness = 1/2" (12.5 mm) for studs spaced at 16" (40.6 cm) o.c.;

3/4" (19 mm) for studs spaced at

24" (61.0 cm) o.c.

Note: See section “Waterproofing” on the use of KERDI-BOARD in bonded waterproofing assemblies.

Spot-bonded KERDI-BOARD

Minimum board thickness = 3/8" bond.

(9 mm)

1. Remove all surface contaminants from the substrate that may weaken the

2. Place spots of thin-set mortar on the

KERDI-BOARD panel or substrate in intervals of approx. 12" (30 cm) .

The mortar must bond to the substrate and mechanically anchor the fleece on the KERDI-BOARD surface.

3. Apply the panels to the wall, firmly press them in place, and align them with a straight-edge or level.



Note: If the bond between the thin-set mortar and substrate is questionable, additional mechanical attachment with the KERDI-BOARD-ZSD anchors or KERDI-BOARD-ZT washers and corresponding screws is required.

Fastener locations must coincide with mortar spots. This may be ensured by making holes in the KERDI-BOARD at the desired fastener locations prior to applying mortar spots. Fasteners are installed after the thin-set mortar has hardened.


Use of KERDI-BOARD on wood or metal framing

1. KERDI-BOARD can be mounted vertically or horizontally on wood or metal framing with appropriate screws

(i.e., coarse thread wood screw for wood studs and self-tapping for metal studs) and corresponding KERDI-

BOARD-ZT washers.

2. The selected screws must be of

SUBSTRATE, BUILDING PANEL, BONDED WATERPROOFING sufficient length to reach a depth of at least 3/4" (20 mm) in wood studs and at least 3/8" (10 mm) in metal studs. The maximum allowable on-center fastener spacing is 12" (30 cm) for walls and 6"

(15 cm) for ceilings. Screws may be placed between adjacent panels such that the washers fasten both panel edges.



a thickness of 3/4" (19 mm) may be used for building shelving. Again, this must be evaluated in accordance with the building specifications.

5. The tiles can be installed using unmodified thin-set mortar once the bonding materials used to construct the partition have cured sufficiently to stabilize the assembly. Choose a notched trowel to match the tile format, and back-butter the tiles, if necessary, to attain full coverage.

using unmodified thin-set mortar.


Note: Please refer to the Walls and

Countertops Profiles data sheet for additional information on profiles, including installation instructions.

A bearing plate must be provided for fastening fixtures (e.g., faucet, soap dispenser, etc.) in tiled-under sink applications to distribute the pressure of the fixture hardware on the underside of the assembly. This may be performed

Note: See section “Waterproofing” on the use of KERDI-BOARD in bonded


by routing a section from the top of the KERDI-BOARD in the area where waterproofing assemblies.

Use of KERDI-BOARD in non-bearing partition wall systems

Countertops made of

KERDI-BOARD

Minimum board thickness = 1-1/2" (38 mm) the fixtures are to be placed. Apply a corresponding piece of ceramic tile with thin-set mortar in the resulting space flush with the surface of the

Minimum board thickness = 2" (50 mm) 1. KERDI-BOARD is adhered directly

KERDI-BOARD. In general, it is recommended that the tile be at

1. Schluter ® -KERDI-BOARD is adhered to base cabinets using the

Schluter ® -KERDI-FIX adhesive. All joints least 5/16" (8 mm) -thick and extend approximately 1-1/2" (38 mm) beyond to the permanent wall in such a way as to provide lateral stability. This can be achieved by sandwiching the panel between adjacent KERDI-

BOARD panels, fixed building elements, etc. As an alternative, the

KERDI-BOARD-ZW angle profile or

KERDI-BOARD-ZB U-shaped profile may be screw-mounted to the wall prior to partition installation.

2. Open-ended partition walls can be of KERDI-BOARD panels must be sealed with KERDI-FIX or thin-set mortar.

2. The backsplash may consist of

KERDI-BOARD or other appropriate tile substrate. Seal the countertop/ backsplash transition with Schluter ® -

KERDI-BAND using unmodified thin-set mortar.

3. Countertop edges may be finished the fixture hardware on all sides. Once the countertop is tiled and grouted, holes may be drilled through the assembly to fit the fixture-mounting studs. Additional material may be removed from the underside of the

KERDI-BOARD to allow installation of the fixture hardware.

with the KERDI-BOARD-ZC brushed stainless steel U-profile and

Pipe and column coverings made of KERDI-BOARD

further stabilized with the corresponding KERDI-BOARD-ZA/-ZB

U-shaped profiles. If you plan to screw finishing hardware (e.g., shower door corresponding Schluter or Schluter ®

® -QUADEC

-RONDEC, RONDEC-CT, or RONDEC-STEP profiles.

a. Apply KERDI-FIX to the inside vertical hinges) to the U-shaped profile, adhere the matching KERDI-BOARD-ZFP flat plastic profile to the back of the U-shaped profile to improve the fastening of the surface of the KERDI-BOARD-ZC profile and slide the profile over the edge of the KERDI-BOARD, pushing it tightly against the panel. The corresponding screws. U-shaped profiles may also be used for connections in the floor and ceiling areas.

3. If multiple KERDI-BOARD panels are required to create the desired partition, the panels must be arranged horizontally with the joints sealed using thin-set mortar or

QUADEC or RONDEC profiles are installed with unmodified thin-set mortar in conjunction with the tile.

b. RONDEC-CT and RONDEC-STEP profiles are installed with unmodified thin-set mortar in conjunction with the tile.

4. The countertop/backsplash transition

Schluter ® -KERDI-FIX adhesive. The

KERDI-BOARD-ZW angle profile or

KERDI-BOARD-ZB U-shaped profile may be included in the joints for improved stability.

4. Such partition walls are not to be considered load-bearing structural walls. As a rule, use the 2" (50 mm) panels for these elements. Panels from may be finished with one of the

Schluter ® -DILEX cove-shaped profiles.

Various materials and finishes are available to match the sink rail profiles above.

5. Sinks may be mounted on top of the tile or tiled-under using RONDEC or

QUADEC profiles and corresponding sink corners.

6. The tiles can be installed immediately

1. The KERDI-BOARD-E/-U L-shaped and

U-shaped panels allow for quick and easy covering of pipes and columns.

2. The panels feature V-shaped grooves.

They are supplied flat, which makes them easy to cut to the required size.

3. Apply thin-set mortar, KERDI-FIX adhesive, or the KERDI-BOARD-ZDK double-sided adhesive tape to the

V-shaped grooves. Fold the panels prior to installation.

4. Adhere the edges of the L-shaped or

U-shaped panels to the existing walls using either thin-set mortar or

KERDI-FIX. If required, mount the

KERDI-BOARD-ZW angle profile on the wall area first for reinforcement.



Note: As an alternative, you can also cut a single U-shaped panel into two

3


L-shaped panels with shorter legs.


Curved wall areas made of

KERDI-BOARD

1. The Schluter ® -KERDI-BOARD-V panels feature grooves to allow for quick and easy creation of curved elements.

2. First, cut the panels to the required size.

If a larger expanse of panels is required, several panels can be connected along the edges with thin-set mortar,

KERDI-BOARD-SB bench

KERDI-BOARD-SC curb

1. Apply unmodified thin-set mortar to the floor and to the edge of the shower base and walls using a 1/4" x 3/8"

(6 mm x 10 mm) square- or U-notched trowel.

2. Press the curb or ramp firmly into place.

Check the underside of the curb or ramp to ensure that full coverage and support is achieved.

3. Seal the curb to the base and walls using KERDI-KERECK and KERDI-

BAND.

KERDI-BOARD-SN shower niche

slope, or the tile may be set on a slope during installation, to prevent water from pooling in the finished application.

Continue setting tile using unmodified thin-set mortar.

Waterproofing with KERDI-BOARD

Schluter ® -KERDI-FIX adhesive, or the

KERDI-BOARD-ZDK double-sided 1. Determine desired location and trace adhesive tape.

3. If the grooved surface points toward the inside, it is recommended that the grooves be filled with thin-set mortar prior to panel installation.

4. Outward-facing grooves should be filled with thin-set mortar prior to or during around the outside of the Schluter ® -

KERDI-BOARD-SN flange, making sure the lines are level and plumb. Cut and remove the wallboard such that the niche will be supported on both sides by the studs or other wall framing.

2. Insert the niche and fasten to the studs. the tile installation.

5. The tiles can be installed using

When installing adjacent to KERDI-

BOARD, use wood or metal screws and unmodified thin-set mortar once the bonding materials used to construct the element have cured sufficiently to stabilize the assembly. Choose a notched trowel to match the tile format, and back-butter the tiles, if necessary, to attain full coverage connections to fixed building elements such as door and window frames. Where these surfaces will not accept a bond to unmodified thin-set mortar, use KERDI-FIX to bond KERDI-BAND.

Separate KERDI-BOARD above the existing movement joints and structural joints and cover the joints with Schluter using unmodified thin-set mortar, ensuring a minimum 2" (50 mm) overlap.

® -KERDI-FLEX

KERDI-BOARD-ZT washers, placing the fasteners along the seam between the

KERDI-BOARD and the niche. When installing adjacent to gypsum board or other tile backers (e.g., CBU), use wood or metal screws only (i.e., no washers), placing fasteners approximately

1/4" (6 mm) from the edges of the niche.

Fastener penetrations may be sealed with KERDI-BAND using unmodified thinset mortar.

Please refer to the Schluter ® -Shower

System Installation Handbook for guidelines on waterproofing showers, steam showers, and tub surrounds.


Fasten all corners and limit fastener spacing to 12" (305 mm) o.c.

3. Connections between the niche and walls are made using KERDI-BAND

Note: Certain glass tiles may not be compatible with bonded waterproofing applications and/or may require special or KERDI. When installed adjacent to

KERDI-BOARD, seams are most easily

Where waterproofing is desired, the joints and corners of KERDI-BOARD in the area must be sealed with KERDI-BAND using unmodified thin-set mortar. The

KERDI-BAND must overlap panel joints by at least 2" (50 mm) .

KERDI-BAND is also suitable for sealing setting materials. Consult glass tile manufacturer and Schluter-Systems for more information.

1. Apply unmodified thin-set mortar to the floor and walls using a 1/4" x 3/8"

(6 mm x 10 mm) square- or U-notched trowel.

2. Press the bench firmly into place and check the underside and backsides to ensure that full coverage and support are achieved. Verify that the slope on the surface of the bench is directed toward the shower base.

3. Install KERDI-BAND and KERDI-

KERECK and KERDI-KERS-B (for triangular bench) to cover all seams and corners, ensuring a minimum 2"

(50 mm) overlap, and work the membrane into the mortar to achieve full coverage and remove air pockets.

constructed using KERDI-BAND. When installed adjacent to gypsum board or other tile backers (e.g., CBU), seams are most easily constructed by continuous application of the KERDI membrane.

The membrane is applied up to the niche opening. Once the niche is sealed to the wall assembly, tile can be installed immediately using unmodified thin-set mortar.

4. When using the prefabricated shelf, determine the desired height of the shelf and mark with a level line. Set tile using unmodified thin-set mortar up to that line on the back and sides of the niche. Butter the sides and back of the shelf with unmodified thin-set mortar and solidly embed it in the niche, resting on the previously installed tile. The shelf may be raised at the back to create a

Certain moisture-sensitive stones, e.g., green marble, or resin-backed tiles may not be appropriate for use in wet areas or may require special setting materials. Consult stone supplier and Schluter-Systems for more information.

If installing bathroom fixtures such as grab bars in showers, wall-mounted toilets, or other heavy objects, the fixtures must be anchored in the structure or solid blocking behind KERDI-BOARD.

Note: Reinforcement may be required behind the entire footprint of the object.

For example, place solid blocking behind the base of a wall-mounted toilet installed over KERDI-BOARD on stud framing.

4

SUBSTRATE, BUILDING PANEL, BONDED WATERPROOFING

Product Item Numbers

Schluter ® -KERDI-BOARD Waterproof building panel

Item No.

Width

Panel dimension: 48" x 32" – 122 cm x 81 cm

KB 12 1220 812 48" – 122 cm

Panel dimension: 48" x 64" – 122 cm x 162.5 cm

KB 5 1220 1625 48" – 122 cm

KB 9 1220 1625

KB 12 1220 1625

48" – 122 cm

48" – 122 cm


KB 5 1220 2440 48" – 122 cm

KB 9 1220 2440

KB 12 1220 2440

KB 15 1220 2440

48" – 122 cm

48" – 122 cm

48" – 122 cm

Panel dimension: 24-1/2" x 96" – 62.5 cm x 244 cm

KB 19 625 2440

KB 25 625 2440

24-1/2" –

24-1/2" –

62.5 cm

62.5 cm

KB 38 625 2440

KB 50 625 2440

24-1/2" – 62.5 cm

24-1/2" – 62.5 cm


KB 15 1220 3050 48" – 122 cm

Length

32" – 81 cm

64" – 162.5 cm

64" – 162.5 cm

64" – 162.5 cm

96" – 244 cm

96" – 244 cm

96" – 244 cm

96" – 244 cm

96" – 244 cm

96" – 244 cm

96" – 244 cm

96" – 244 cm

120" – 305 cm

Thickness

1/2" – 12.5 mm

3/16" – 5 mm

3/8" – 9 mm

1/2" – 12.5 mm

3/16" – 5 mm

3/8" – 9 mm

1/2" – 12.5 mm

5/8" – 15 mm

3/4" – 1 9 mm

1" – 25 mm

1-1/2" – 38 mm

2" – 50 mm

5/8" – 15 mm

Schluter

®

-KERDI-BOARD-V Waterproof building panel

Item No.

KB 19 625 2440 V

KB 25 625 2440 V

KB 38 625 2440 V

KB 50 625 2440 V

Width

24-1/2" – 62.5 cm

24-1/2" – 62.5 cm

24-1/2" – 62.5 cm

24-1/2" – 62.5 cm

Length

96" – 244 cm

96" – 244 cm

96" – 244 cm

96" – 244 cm

Thickness

3/4" – 1 9 mm

1" – 25 mm

1-1/2" – 38 mm

2" – 50 mm

Schluter

®

-KERDI-BOARD-E Waterproof building panel

Item No.

KB 19 625 2440 E

KB 25 625 2440 E

Width

24-1/2" – 62.5 cm

24-1/2" – 62.5 cm

Length

96" – 244 cm

96" – 244 cm

Thickness

3/4" – 1 9 mm

1" – 25 mm

Schluter ® -KERDI-BOARD-U Waterproof building panel

Item No.

KB 19 625 2440 U20

KB 19 625 2440 U30

Width

8-1/4" x 7-7/8" x 8-1/4" = 24-1/2" – 21 x 20 x 21 cm = 62 cm

Length

96" – 244 cm

6-5/16" x 11-13/16" x 6-5/16" = 24-1/2" – 16 x 30 x 16 cm = 62 cm 96" – 244 cm

Thickness

3/4" – 19 mm

3/4" – 19 mm

Schluter

®

-KERDI-BOARD-SN Shower niche

Item No.

KB 12 SN 305 152 A

KB 12 SN 305 305 A

KB 12 SN 305 508 A1

KB 12 SN 305 711 A1

Size

12" x 6" – 305 mm x 152 mm

12" x 12" – 305 mm x 305 mm

12" x 20" – 305 mm x 508 mm

12" x 28" – 305 mm x 711 mm

Depth

3-1/2" – 89 mm

3-1/2" – 89 mm

3-1/2" – 89 mm

3-1/2" – 89 mm

Shelf

-

-

1

1

12.1 Schluter ® -KERDI-BOARD-SC Prefabricated curb

Item No.

KBSC 115 150 970

KBSC 115 150 1220

Width

4-1/2" – 11.5 cm

4-1/2" – 11.5 cm

Length

48" – 122 cm

38" – 97 cm

Height

6" - 15 cm

6 " - 15 cm

12.1 Schluter ® -KERDI-BOARD-SB Prefabricated bench

Item No.

KBSB 410 TA

KBSB 610 TA

KBSB 290 970 RA

KBSB 410 1220 RA

Width

16" – 41 cm

24" – 61 cm

38" – 97 cm

48" – 122 cm

Length

16" – 41 cm

24" – 61 cm

11-1/2" – 29 cm

16" – 41 cm

Height

20" - 51 cm

20" - 51 cm

20" - 51 cm

20" - 51 cm

Shape

Triangular

Triangular

Rectangular

Rectangular

5

6


Schluter

®

-KERDI-BOARD-ZW

Item No.

Length supplied: 6"— 15 cm

KB ZW 30 E/15

Length supplied: 8' 2-1/2" — 2.50 m

KB ZW 30 E

Description

Stainless steel angle profile

Stainless steel angle profile

Schluter ® -KERDI-BOARD-ZC

Item No.


KB ZC 38 EB

KB ZC 50 EB

Description

U-shaped brushed stainless steel profile with 1 perforated anchoring leg

U-shaped brushed stainless steel profile with 1 perforated anchoring leg

Size

1-1/2" – 38 mm

2" – 50 mm

Schluter ® -KERDI-BOARD-ZC/E

Item No.

E/KB ZC 38 EB

E/KB ZC 50 EB

Description

Brushed stainless steel outside corner piece for ZC

Brushed stainless steel outside corner piece for ZC

Size

1-1/2" – 38 mm

2" – 50 mm

Schluter

®

-KERDI-BOARD-ZA

Item No.


KB ZA 19 EB

KB ZA 25 EB

Description

U-shaped brushed stainless steel profile with 2 perforated anchoring legs


KB ZA 38 EB

KB ZA 50 EB



Size

3/4" – 19 mm

1" – 25 mm

1-1/2" – 38 mm

2" – 50 mm

Schluter ® -KERDI-BOARD-ZA/E

Item No.

E/KB ZA 38 EB

E/KB ZA 50 EB

Description

Brushed stainless steel outside corner piece for ZA

Brushed stainless steel outside corner piece for ZA

Size

1-1/2" – 38 mm

2" – 50 mm

Schluter ® -KERDI-BOARD-Z/V

Item No.


V/KB Z 19 EB

V/KB Z 25 EB

V/KB Z 38 EB

V/KB Z 50 EB

Description

Brushed stainless steel connector for ZC and ZA




Size

3/4" – 19 mm

1" – 25 mm

1-1/2" – 38 mm

2" – 50 mm


Schluter ® -KERDI-BOARD-ZI/V

Item No.

V/KB ZI 19 E

V/KB ZI 25 E

V/KB ZI 38 E

V/KB ZI 50 E

Description

Stainless steel internal connector for ZC and ZA




Size

3/4" – 19 mm

1" – 25 mm

1-1/2" – 38 mm

2" – 50 mm

Schluter ® -KERDI-BOARD-ZB

Item No.


KB ZB 19 E

KB ZB 25 E

KB ZB 38 E

KB ZB 50 E

Description

U-shaped stainless steel profile with 3 perforated anchoring legs




Schluter ® -KERDI-BOARD-ZSD

Item No.

Description

KB ZSD 90 E Stainless steel anchor

KB ZSD 110 E

KB ZSD 90 Z

KB ZSD 110 Z

Stainless steel anchor

Galvanized steel anchor

Galvanized steel anchor

Length

3-1/2" – 9 cm

4-5/16" – 11 cm

3-1/2" – 9 cm

4-5/16" – 11 cm

Schluter ® -KERDI-BOARD-ZDK

Item No.

KB ZDK 12/10M

KB ZDK 19/10M

KB ZDK 30/10M

Description

Double-sided tape

Double-sided tape

Double-sided tape

Schluter ® -KERDI-BOARD-ZSA

Item No.

KB ZSA 100/45M

Description

Joint reinforcement tape

Size

3/4" – 19 mm

1" – 25 mm

1-1/2" – 38 mm

2" – 50 mm

Packaging

25 anchors/box

25 anchors/box

25 anchors/box

25 anchors/box

Size

1/2" x 33' – 12.5 mm x 10 m

3/4" x 33' – 19 mm x 10 m

1-3/16" x 33' – 30 mm x 10 m

Size

4" x 148' - 100 mm x 45 m

7

8


Schluter ® -KERDI-BOARD-ZFP

Item No.

KB ZFP 35

8.1 Schluter

®

-KERDI-BAND

Item No.

KEBA 100/125/5M

KEBA 100/125/10M

KEBA 100/185/5M

KEBA 100/250/5M

KEBA 100/125

KEBA 100/185

KEBA 100/250

Width

5" – 12.5 cm

5" – 12.5 cm

7-1/4" – 18.5 cm

10" – 25 cm

5" – 12.5 cm

7-1/4" – 18.5 cm

10" – 25 cm

Description

Flat plastic profile

Length

16' 5" – 5 m

33' – 10 m

16' 5" – 5 m

16' 5" – 5 m

98' 5" – 30 m

98' 5" – 30 m

98' 5" – 30 m

Size

1-3/8" x 8' - 35 mm x 2.5 m

Waterproofing strips

Thickness

4 mil

4 mil

4 mil

4 mil

4 mil

4 mil

4 mil

8.1 Schluter ® -KERDI-FLEX

Item No.

FLEX 125/5M

Waterproofing strips for use above movement joints

Width Length

5" – 12.5 cm 16' 5" – 5 m

Thickness

12 mil

FLEX 250/5M

FLEX 125/30

FLEX 250/30

10" – 25 cm 16' 5" – 5 m

5" – 12.5 cm 98' 5" – 30 m

10" – 25 cm 98' 5" – 30 m

12 mil

12 mil

12 mil

8.1 Schluter ® -KERDI-KERECK-F

Item No.

KERECK / FI 2

KERECK / FI 10

KERECK / FA 2

KERECK / FA 10

Thickness

4 mil

4 mil

4 mil

4 mil

Pre-formed corners

Packaging

2 Inside corners

10 Inside corners

2 Outside corners

10 Outside corners

8.1 Schluter ® -KERDI-KERS-B Preformed corner

Item No.

KERECK135/FI2

KERECK135/FI10

KERSB135KLR

KERSB135K5LR

KERSB135K

Thickness

4 mil

4 mil

4 mil

4 mil

4 mil

Description

Inside corner, 135°

Inside corner, 135°

Bench corners

Bench corners

Bench/ neo-angle corner kit

Packaging

2 units

10 units

1 right and 1 left

5 right and 5 left

1 right and 1 left bench corner, and

2 135° inside corners


8.1 Schluter

®

-KERDI-SEAL-PS Pipe seal with over-molded rubber gasket

Item No.

Pipe nipple opening diam.

Thickness Packaging

KMS 185/12

KMS 185/20

KMS 10185/12

KMS 10185/20

1/2" - 12.5 mm

3/4" - 20 mm

1/2" - 12.5 mm

3/4" - 20 mm

4 mil

4 mil

4 mil

4 mil

1 unit

1 unit

10 units

10 units

8.1 Schluter ® -KERDI-SEAL-MV Mixing valve seal with over-molded rubber gasket

Item No.

Mixing valve opening diam.

Thickness Packaging

KMS MV 235/114

KMS MV 10235/114

4-1/2" - 114 mm

4-1/2" - 114 mm

4 mil

4 mil

1 unit

10 units

8.3 Schluter ® -KERDI-FIX Adhesive/sealant

Item No.

KERDIFIX / color*

KERDIFIX 100 G

Description

Cartridge - 9.81 oz (290 ml)

Tube - 3.38 oz (100 ml)

* Color Codes

BW

Bright white

G

Grey

To complete the item number, add the color code (e.g., KERDIFIX / BW ).

Schluter ® -KERDI-BOARD-ZT

Item No.

Description

KB ZT 32 Z Galvanized steel attachment washers

KB ZT 32 Z/L Galvanized steel attachment washers

Schluter

®

-KERDI-BOARD-ZS

Item No.

KB ZS 35 G

KB ZS 55 G

KB ZS 75 G

Description

Course thread screw for wood framing



Schluter

®

-KERDI-BOARD-ZT/-ZS

Item No.

KB ZS 35 GT 32 Z

Description

Washer and screw set

Size

1-1/4" – 32 mm

1-1/4" – 32 mm

Size

1-5/8" – 41 mm

2" – 50 mm

3" – 75 mm

Size

1-5/8" – 41 mm

Packaging

100 washers/box

1000 washers/box

Packaging

200 screws/box

100 screws/box

100 screws/box

Packaging

40 each/box

9


Schluter

®

-KERDI-BOARD 10-Year Limited Warranty

COVERAGE AND CONDITIONS: Subject to the conditions and limitations as stated hereinafter, Schluter-Systems* warrants that

Schluter ® -KERDI-BOARD (the “Product”) will be free from all manufacturing defects, and will not rot, deteriorate or break down under normal use for a period of ten (10) years from the date of purchase only when the Product is used and installed in accordance with the terms and conditions of the

Schluter ® -KERDI-BOARD Technical Data Sheet and industry standard guidelines that are not in conflict with the Data Sheet in effect at the time of installation.

Further, efflorescence is considered to be a natural occurrence with cementitious materials and is therefore not considered to be a defective condition and is not covered by this warranty. It is the responsibility of the owner/ builder/ installer to ensure the suitability of all building materials and all associated building materials for the owner’s intended use. It is recommended that the owner consult with an experienced and professional installer.

RESOLUTION: If the Product fails to meet this warranty, then the owner’s exclusive remedy and the sole obligation of Schluter-Systems, at its election, shall be to a) reinstall or replace the failed portion of the tile assembly or b) pay an amount not to exceed the original square foot cost of the installation of the tile assembly verified to be defective. Tile assembly is defined to include all KERDI-BOARD materials, non-reusable tile surfaces, and the appropriate setting and grouting materials. Further, due to conditions beyond the control of Schluter-Systems (e.g., color and shade availability, discontinuation, normal wear and tear),

Schluter-Systems cannot guarantee or warrant an exact match to the specific tile, stone, or other covering materials used in the installation. In such events, substantially similar materials may be substituted.

DISCLAIMER: THERE ARE NO WARRANTIES BEYOND THIS EXPRESSED WARRANTY AS STATED ABOVE. ALL OTHER WARRANTIES,

REPRESENTATIONS OR CONDITIONS, EXPRESSED OR IMPLIED, ARE DISCLAIMED AND EXCLUDED, INCLUDING WARRANTIES, REPRESENTATIONS

OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARISING BY STATUTE OR OTHERWISE BY LAW OR FROM A

COURSE OF DEALING OR USAGE OF TRADE. SCHLUTER-SYSTEMS EXCLUDES AND IN NO EVENT SHALL HAVE ANY LIABILITY FOR LOST PROFITS

OR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY, OR CONSEQUENTIAL DAMAGES, ARISING OUT OF OR OTHERWISE

CONNECTED TO FAILURE OF THE PRODUCT OR TILE ASSEMBLY OF WHICH IT IS PART, NOR MISUSE OF THE PRODUCT OR TILE ASSEMBLY, REGARDLESS

OF ANY STRICT LIABILITY, ACTIVE OR PASSIVE NEGLIGENCE OF SCHLUTER-SYSTEMS, AND REGARDLESS OF THE LEGAL THEORY (CONTRACT OR TORT

OR EXTRA-CONTRACTUAL OR OTHER), NOR FROM ACTS OF WAR, TERRORISM, FAULTY AND NEGLIGENT PENETRATION OF THE SYSTEM,

FIRES, EXPLOSIONS, ACTS OF GOD, INTENTIONAL ACTS OF DESTRUCTION OR ANY LOSSES DUE TO STRUCTURAL FAILURE OR OTHER CAUSES

UNRELATED TO THE PRODUCT OR DELAYS, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS GIVEN IN LIEU OF

ANY OTHER WARRANTY EXPRESSED OR IMPLIED. THE REMEDIES CONTAINED HEREIN ARE THE ONLY REMEDIES AVAILABLE FOR BREACH OF

THIS WARRANTY. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS; SOME STATES AND PROVINCES DO NOT ALLOW DISCLAIMERS

OR OTHER RESTRICTIONS OF IMPLIED WARRANTIES, SO SOME OF THE ABOVE DISCLAIMERS MAY NOT APPLY TO YOU.

TRANSFERABILITY: This Limited Warranty extends ONLY to the original end user (defined as original intended owner and user of the property/unit in which the installation is incorporated - herein referred to as “Owner”) and is not transferable or assignable, unless approved in writing by the Technical Director or an Officer of Schluter-Systems or otherwise prohibited by specific state or provincial law.

MODIFICATIONS TO WARRANTY: No changes or modification of any terms or conditions of this warranty are allowed unless authorized by written agreement and signed by the Technical Director or an Officer of Schluter-Systems.

EFFECTIVE DATE: This warranty shall supersede and replace any and all prior oral or written warranties, agreements, or other such representations made by or on behalf of Schluter-Systems relative to the Product or the application of the Product and shall apply to any installation occurring on or after January 1, 2013.

CLAIMS ON THIS LIMITED WARRANTY: To make a claim under this Limited Warranty, the Owner must provide Schluter-Systems with written notice within 30 days of any alleged defect in the Product covered by this Limited Warranty, together with date and proof of purchase of the Product, proof of the costs of the original installation and name and address of all installers, failing which this Limited Warranty shall be of no legal effect. Schluter-Systems reserves the right at its election and as a condition of this Limited Warranty to inspect the alleged failed and defective condition.

All U.S. Claims shall be sent to: All Canadian Claims shall be sent to:

Schluter Systems L.P.

Attn: Warranty Claims Dept.

194 Pleasant Ridge Road

Schluter Systems (Canada), Inc.


21100 chemin Ste-Marie

Plattsburgh, NY 12901-5841 Ste-Anne-de-Bellevue, QC H9X 3Y8

*For the purpose of this warranty Schluter Systems, L.P. shall provide the warranty for all products for end users located in the United States, and

Schluter Systems (Canada) Inc.

shall provide the warranty for all products for end users located in Canada. This warranty is limited to sales of the Product made in and intended for use in the United States and Canada.

10


Schluter

®

-KERDI-BOARD Profiles 5-Year Limited Warranty

COVERAGE AND CONDITIONS: Subject to the conditions and limitations as stated hereinafter, Schluter-Systems* warrants that Schluter ® -KERDI-BOARD

Profiles (the “Products”)** will be free from manufacturing defects for a period of five (5) years from the date of purchase and only when the Products are used and installed in accordance with the terms and conditions of the Schluter ® -KERDI-BOARD Technical Data Sheet and industry standard guidelines that are not in conflict with the Data Sheet in effect at the time of installation. It is the responsibility of the owner/builder/installer to ensure the suitability of all building materials and all associated building materials for the owner’s intended use. Visual defects or nonconformities apparent prior to installation are not covered by this warranty.

Further, this warranty does not cover normal wear and tear or other damage (e.g., scratches, discoloration, fading, etc.) caused by impacts or accidents. It is recommended that the owner consult an experienced and professional installer.

RESOLUTION: If the Products fail to meet this warranty, then the owner’s exclusive remedy and the sole obligation of Schluter-Systems, at its election, shall be to a) reinstall or replace the failed portion of the tile assembly or b) pay an amount not to exceed the original square foot cost of the installation of the tile assembly verified to be defective. Tile assembly is defined to include all Schluter ® -KERDI-BOARD Profiles, non-reusable tile surfaces, and the appropriate setting and grouting materials. Further, due to conditions beyond the control of Schluter-Systems (e.g., color and shade availability, discontinuation, normal wear and tear), Schluter-Systems cannot guarantee or warrant an exact match to the specific tile, stone, or other covering materials used in the installation.

In such events, substantially similar materials may be substituted.

DISCLAIMER: THERE ARE NO WARRANTIES BEYOND THIS EXPRESSED WARRANTY AS STATED ABOVE. ALL OTHER WARRANTIES,

REPRESENTATIONS OR CONDITIONS, EXPRESSED OR IMPLIED, ARE DISCLAIMED AND EXCLUDED, INCLUDING WARRANTIES, REPRESENTATIONS

OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARISING BY STATUTE OR OTHERWISE BY LAW OR FROM A

COURSE OF DEALING OR USAGE OF TRADE. SCHLUTER-SYSTEMS EXCLUDES AND IN NO EVENT SHALL HAVE ANY LIABILITY FOR LOST PROFITS

OR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY, OR CONSEQUENTIAL DAMAGES, ARISING OUT OF OR OTHERWISE

CONNECTED TO FAILURE OF THE PRODUCTS OR TILE ASSEMBLY OF WHICH THEY ARE PART, NOR MISUSE OF THE PRODUCTS OR TILE ASSEMBLY,

REGARDLESS OF ANY STRICT LIABILITY, ACTIVE OR PASSIVE NEGLIGENCE OF SCHLUTER SYSTEMS, AND REGARDLESS OF THE LEGAL THEORY

(CONTRACT OR TORT OR EXTRA-CONTRACTUAL OR OTHER), NOR FROM ACTS OF WAR, TERRORISM, FAULTY AND NEGLIGENT PENETRATION

OF THE SYSTEM, FIRES, EXPLOSIONS, ACTS OF GOD, INTENTIONAL ACTS OF DESTRUCTION OR ANY LOSSES DUE TO STRUCTURAL FAILURE OR

OTHER CAUSES UNRELATED TO THE PRODUCTS OR DELAYS, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS

GIVEN IN LIEU OF ANY OTHER WARRANTY EXPRESSED OR IMPLIED. THE REMEDIES CONTAINED HEREIN ARE THE ONLY REMEDIES AVAILABLE

FOR BREACH OF THIS WARRANTY. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, SOME STATES AND PROVINCES DO NOT

ALLOW DISCLAIMERS OR OTHER RESTRICTIONS OF IMPLIED WARRANTIES SO SOME OF THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

TRANSFERABILITY: This Limited Warranty extends ONLY to the original end user (defined as original intended owner and user of the property/unit in which the installation is incorporated - herein referred to as “Owner”) and is not transferable or assignable, unless approved in writing by the Technical Director or an Officer of Schluter-Systems or otherwise prohibited by specific state or provincial law.

MODIFICATIONS TO WARRANTY: No changes or modification of any terms or conditions of this warranty are allowed unless authorized by written agreement and signed by the Technical Director or an Officer of Schluter-Systems.

EFFECTIVE DATE: This warranty shall supersede and replace any and all prior oral or written warranties, agreements, or other such representations made by or on behalf of Schluter-Systems relative to the Products or the application of the Products and shall apply to any installation occurring on or after January 1, 2013.

CLAIMS ON THIS LIMITED WARRANTY: To make a claim under this Limited Warranty, the Owner must provide Schluter-Systems with written notice within 30 days of any alleged defect in the Products covered by this Limited Warranty, together with date and proof of purchase of the Products, proof of the costs of the original installation and name and address of all installers, failing which this Limited Warranty shall be of no legal effect. Schluter-Systems reserves the right at its election and as a condition of this Limited Warranty to inspect the alleged failed and defective condition.

All U.S. Claims shall be sent to: All Canadian Claims shall be sent to:



194 Pleasant Ridge Road

Schluter Systems (Canada), Inc.


21100 chemin Ste-Marie

Plattsburgh, NY 12901-5841 Ste-Anne-de-Bellevue, QC H9X 3Y8

*For the purpose of this warranty Schluter Systems, L.P.

shall provide the warranty for all products for end users located in the United States, and

Schluter Systems (Canada) Inc. shall provide the warranty for all products for end users located in Canada. This warranty is limited to sales of the

Products made in and intended for use in the United States and Canada.

**Schluter ® -KERDI-BOARD Profiles (the “Products”): The Products are defined to include all Schluter ® -KERDI-BOARD profiles referred to in the

Schluter ® -KERDI-BOARD Data Sheet.

11


•

194 Pleasant Ridge Road, Plattsburgh, NY 12901-5841

•

Tel.: 800-472-4588

•

Fax: 800-477-9783

Schluter Systems (Canada) Inc.

•

21100 chemin Ste-Marie, Ste-Anne-de-Bellevue, QC H9X 3Y8

•

Tel.: 800-667-8746

•

Fax: 877-667-2410

www.schluter.com

This technical data sheet is subject to change without notice. Please visit www.schluter.com for the latest version.

Schluter KB506252440 Kerdi-Board 2 in. x 24-1/2 in. x 96 in. Building Panel Use and Care Manual

SCHLUTER

-KERDI-BOARD

Application and Function

-KERDI-BOARD

Material Properties and

Areas of Application

Installation

Fully embedded KERDI-BOARD

Spot-bonded KERDI-BOARD

Use of KERDI-BOARD on wood or metal framing

Use of KERDI-BOARD in non-bearing partition wall systems

Countertops made of

KERDI-BOARD

Pipe and column coverings made of KERDI-BOARD

Curved wall areas made of

KERDI-BOARD

KERDI-BOARD-SB bench

KERDI-BOARD-SC curb

KERDI-BOARD-SN shower niche

Waterproofing with KERDI-BOARD

Product Item Numbers

* Color Codes

Schluter

-KERDI-BOARD 10-Year Limited Warranty

Schluter

-KERDI-BOARD Profiles 5-Year Limited Warranty

www.schluter.com

Related manuals

Schluter Systems

KB1212202440

Schluter Systems

KB12SN305711A1

Schluter Systems

KB121220812

Pittsburgh Corning

110950

Everbilt

EVB60SC

Everbilt

EVB60SC

Schluter

RO100AMG

Schluter Systems

KERDIFIX/BW

Schluter Systems

KB1212202440

Schluter

SES2D6EB

Schluter

KST965/1525

Schluter

KKB81152ABSAKGB