ZLINE Kitchen and Bath 623-48 ZLINE 48 in. 900 CFM Under Cabinet Range Hood in Stainless Steel Installation Guide

ZLINE Kitchen and Bath 623-48 ZLINE 48 in. 900 CFM Under Cabinet Range Hood in Stainless Steel Installation Guide
KITCHEN AND BATH
Installation Guide 6 Users Manual
IMPORTANT:
Read and save these instructions.
NOTICE:
Installer: Leave this guide with the homeowner 520 / 523 / 527
Homeowner: Keep this guide for future reference
Under Cabinet/ Wall Mount Range Hood
Advanced Preparations:
Be familiar with the controls of the range hood by reading
through Range Hood Operations, Page 12.
Place the range hood on a flat, stable surface. Connect the
range hood to a designated standard outlet (120-Volt, 60Hz,
AC only) and turn on the range hood. Verify all operations
of the range hood by referring to Range Hood Operations
Page 13.
Place all supplied parts and required hardware on a flat, stable surface and verify
the existence of all supplied parts listed on Page 4.
Carefully remove the white plastic protective coat from the range hood.
Preparations:
NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.
Decide the location of the venting pipe from the hood to the outside. Refer to Venting Methods on Page 7.
A straight, short vent run will allow the hood to perform more efficiently.
Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the
hood.
IMPORTANT: Peel white plastic protective coat off the hood, if any.
Use silver tape or duct tape to seal joints between pipe sections.
For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not provided) on
each side. Refer to Figure 1.
Using references in Measurements and Diagrams on Page 16, create access opening for electrical wires and
hood exhaust under the cabinet.
CAUTION: If moving the cooking range is necessary to install the hood, turn OFF the power on an elec-
tric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.
Puncture the knockout holes (for mounting under the cabinet) on the hood as shown in Figure 2.
If necessary, attach two rubber stands with 3M adhesive tapes to the back corners of the hood.
Attach ducting transition to hood exhaust with included 10 round head screws as shown in Figure 3.
Sar?
NO
- ns =
\ O
4" WIDE 4" | 7
Figure 1 Figure 2 Figure 3
Page 8
Installations (refer to Page 4 for parts):
1. Measure the distance between stove top and the bottom of
range hood. A distance of 27” to 30” is recommended™.
*Due to different ceiling height configurations, recom-
mended height may not be applicable.
1. You have two ways (A or B) to mount this range hood:
А-1.
A—2.
A-3.
А-4.
B—3.
B—4.
Вэ.
Proceed if you would like to mount this range hood without using the hood-mounting bracket.
Using references in Height & Clearance on Page 5 and Measurements and Diagrams on Page 16, cen-
ter the hood beneath the cabinet and flush with the front of the cabinet.
Draw electrical wires through cabinet access opening, center the hood beneath the cabinet as shown in Figure 4.
From inside of the hood, place screws into the exact center of each knockout hole and secure to cabinet
bottom. Finish tightening all screws until secure. Be careful when using electrical screwdriver, damage
to the range hood may occur. Skip Part B below and proceed to Step 2.
CAUTION: Make certain the range hood is secure before releasing!
. Proceed if you would like to mount this range hood using the provided hood-mounting bracket.
. Using references in Height & Clearance on Page 5 and Measurements and Diagrams on Page 17, mark
the leveling point of the hood. Position two mounting screws on the wall, leaving 1/8” space away from
the wall. Mounting the hood on wall studs or lumbars 1s highly recommended.
Punchure the knockout wire access hole at the back of the hood and draw the electrical wires through
as shown in Figure 4.
Attach each hood-mounting bracket to the back of the hood with 4 flat head screws as shown in Figure 5.
Align hood-mounting bracket to the screws on the wall and hook hood into place as shown in Figure 6.
Tighten screws to secure hood to the wall.
CAUTION: Make certain the range hood is secure before releasing!
2. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure
installation, use as many mounting holes as needed to secure from the inside of hood.
3. Use 8” round steel pipe (follow building codes in your area) to connect the exhaust on the hood to the duct-
work above. Use silver tape or duct tape to make all joints secure and air tight. Refer to Figure 7.
SAFETY WARNING: Risk of electrical shock. this range hood must be properly grounded. Make sure this
is done by qualified electrician in accordance with all applicable national and local electrical codes. Before
connecting wires, switch power off at service panel and lock service panel to prevent power from being
switched on accidentally.
4. Connect the range hood to a designated standard outlet (120-Volt, 60Hz, AC only) or cut off the plug and con-
nect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to
colors (i.e. black to black, white to white, and green to green) as shown in Figure 8.
Figure 4
Figure 5 Figure 6 Fa
Store excess wires in the wiring box.
OPTIONAL: If you purchased a single-piece chimney cover, attach it to the hood in this step.
Drop oil tunnel into recess support near rear of hood. Refer to Figure 9.
To install baffle filters and stainless spacer(s), refer to Baffle Filters and Stainless Steel Spacers on Page 18 for
baffle filter and stainless spacer placement. Refer to Figure 10 for the following five steps:
(1 Angle baffle filter toward back of hood.
@ Push baffle filter up until almost level.
@ Slide forward into recess behind the front of hood.
@ Lower baffle filter.
O) Slide back until it fits into resting positions.
9. Repeat Step 8 to install all baffle filters and stainless spacers.
10. OPTIONAL: Install heating lamps (not included) last. 120-Volt, 250-Watt maximum per lamp.
11. Turn powe ON in control panel. Check all lights and fan operations.
12. Make sure to leave this Installation Guide for the homeowner.
72
Figure 10
Figure 7
Page 10
Figure 9
1. If the range hood or halogen light does not operate + Check if the range hood has been plugged in, make
after installation: sure that all power has been turned back ON, fused
not blown and all electrical wiring are properly con-
nected.
* Swap out light assembly to working ones to deter-
mine whether it is caused by defective bulbs. See
Replacing the light bulbs on Page 23.
2. The range hood vibrates when the blower is on: ° The range hood might not have been secured prop-
erly on to the ceiling or wall.
3. The blower or fan seems weak: * Check that the duct sized used is at least 8” or 3-1/4
x 10”. Range hood WILL NOT function efficiently
with insufficient duct size. For example: 9” duct
over 8” hole and loosely secured.
+ Check if duct 1s clogged or if damper unit (half-cir-
cular flapper) 1s not installed correctly or opening
properly. A tight mesh on a side wall cap unit might
also cause restriction to the air flow.
4. The lights work but the blower 1s not spinning at all, < The blower might be jammed or scraping the bot-
is stuck or is rattling. tom due to shipping damage. Please contact us im-
mediately.
5. The hood is not venting out properly: + Make sure the distance between the stove top and
the bottom of the hood is within* 27” and 30” in
distance. * Due to different ceiling height configura-
tions, recommended height may not be applicable.
* Reduce the number of elbows and length of duct
work. Check if all joints are properly connected,
sealed, and taped.
+ Make sure the power is on high speed for heavy
cooking.
Page 13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement