Lanco PV360-5 User guide

Lanco PV360-5 User guide
Polyurethane Varnish™ PV-360
Rev. 06 / 2016
Method of Application:
Danger / Warning:
Brush: Apply by brush or roller, use a good brush with natural bristles.
Precaution: Flammable mixture, do not use near fire or flame.
Roller: Use Lanco® All Purpose Roller 3/8” Nap PA-566 or conventional or
airless spray. Roller application may require special care to prevent bubbling
and more than one coat to obtain proper thickness. Apply at 4 mils wet film
thickness that will yield 2 mils dry film thickness. With a clean soft varnish
brush apply a thin, smooth coat brushing in grain direction. Maintain a wet
edge and brush out any lap marks. A second coat, if desired, may be applied
without sanding as soon as first coat is dry. If allowed to dry more than 12
hours, sand or buff with fine sandpaper (#220) or steel wood to insure
proper adhesion between coats. Remove all dust before varnishing.
Contains: Petroleum distillates. Use only with adequate ventilation.
Avoid prolonged or repeated breathing of vapor.
It is important to use adequate ventilation as high vapor concentration may
cause unconsciousness or even asphyxiation. Ventilation must be sufficient
to limit exposure below MSDS limits. Eye irritation and dizziness are
indications of over exposure.
Refer to Lanco® material safety data sheet.
Provide adequate ventilation during application and drying cycles. Do not
take internally. Swallowing may cause injury, illness or death. If swallowed,
Conventional spray: For suction feed, use DeVilbiss MBC gun with “E” tip do not induce vomiting. Call a physician immediately.
and needle and 30 air cap or equivalent at 35-40 psi atomizing pressure
feed. For pressure feed, use DeVilbiss MBC gun with tip and needle and 704 Notice: Reports have associated repeated and prolonged occupational over
air cap or equivalent at 35-40 psi atomizing pressure and 5-8 psi fluid exposure to solvents, with permanent brain and nervous system damage,
pressure, 3/8” ID material hose, double regulated pressure tank with oil and peripheral nervous tissue damage and liver abnormalities. Intentional
moisture separator.
misuse by deliberately concentrating and inhaling the contents may be
harmful or fatal.
Airless spray: Minimum of 28:1 ratio pump, 0.011”-0.013” orifice tip 1/4” Always wear respiratory protection (NIOSH, MSHA TC 23C OR
ID Teflon material hose.
equivalent). Keep out of reach of children.
Limitation: Apply in good weather when air and surface temperature are
above 40ºF and surface temperature is at least 5ºF above the dew point. For
optimum application properties, material should be between 70º to 100ºF
prior to mixing and application.
Note: When multiple coats of product are applied, be sure to sand lightly
between coats with a fine sandpaper and dust clean or vacuum.
Cleanup: Wipe up drips and spatters with Lanco® Mineral Spirits MS-107.
Clean all equipment with this solution.
Caution: Do not take internally. Close container after each use. Keep out of
the reach of children. Combustible; keep away from heat and open flame.
Avoid prolonged contact with skin and breathing vapors or spray mist.
• NORTH AMERICA • 600 Mid Florida Drive Airport Industrial Park of Orlando, Florida 32824 • Tel. (407) 240-4000 Fax (407) 240-4046
• CARIBBEAN & SOUTH AMERICA • Urb. Aponte #5, San Lorenzo, Puerto Rico USA 00754 • Tel. (787) 736-4221 Fax (787) 736-5313
• CENTRAL AMERICA • Zona Industrial Bes, lote #4, El Coyol de Alajuela, Costa Rica • Tel. (506) 2438-2257 Fax (506) 2438-2162
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement