Chem-Tainer Industries TC4772IC-2-BLACK, TC7272IC-2-BLACK, TC4772IC-2-GREEN, TC4642IC-2-BLACK, TC2331IC-2-BLACK, TC4642IC-2-GREEN, TC-2331IC-2-GREEN, TC3731IC-2-BLACK Operating instructions

Chem-Tainer Industries TC4772IC-2-BLACK, TC7272IC-2-BLACK, TC4772IC-2-GREEN, TC4642IC-2-BLACK, TC2331IC-2-BLACK, TC4642IC-2-GREEN, TC-2331IC-2-GREEN, TC3731IC-2-BLACK Operating instructions
Tank Handling, Installation & Use Guidelines
Although Chemtainer’s tanks are extremely durable, improper handling and installation can
result in damage to tank, fittings, and accessories. Failure to comply with handling and
installation instructions voids all warranties.
1. At delivery, inspect your tank immediately for defects or shipping damage. Any
discrepancies, or product problems, should be noted on both the driver's bill of lading and
your packing list.
2. When unloading your tank from the delivery truck, avoid its contact with sharp objects.
Forklift blades can cause significant damage if proper precautions are not taken. Do not
allow tanks to be rolled over on the fittings. Large bulk storage tanks, whenever possible,
should be removed from truck bed by use of a crane or other suitable lifting device. OSHA
regulation 29CFR 1910.178 through 1910.189 addresses specific standards for hoisting and
lifting. Keep unloading area free of rocks, sharp objects, and other materials that could
damage the tank. If tank is unloaded on it's side, carefully brace to prevent rolling.
3. Support bottom of tank firmly and completely. Concrete pads provide the best
foundation. The pad should be clean, smooth, and level so it fully supports the entire tank
bottom with no deflection. However, when seismic and wind factors are not being
considered, tanks with a base load bearing of less than 800 pounds per square foot require
a firm, even, compacted bed of sand, pea gravel, or fine soil that won't wash away. Tanks
with a base load bearing of 800 pounds per square foot, or greater, require a reinforced
concrete base. Steel support stands concentrate the loaded tank weight onto the stand leg
pads. It is recommended that stands are mounted on a concrete base. Bolting of stands is
necessary to prevent movement due to agitation, wind, seismic loads and accidental
4. Install tanks in an area that is accessible. Ease of maintenance and removal should be
5. Test by filling tank with water prior to use, to prevent material loss through unsecured
fittings, shipping damage, or manufacturing defects. Tanks should be tested for a minimum
5 hours.
6. Plastic screw on bulkhead fittings are designed to be hand tightened. Overtightening can
cause fittings to leak.
7. Support sides of rectangular tanks. In general, tanks with heights greater than 18" must
be supported. However, specific applications must be considered: smaller tanks with
contents that have high specific gravity and/or elevated temperatures must be supported.
8. Do not mount heavy equipment on tank sides.
9. Do not allow weight on tank fittings. Fully support pipes and valves.
10. Use expansion joints to prevent damage at fittings from the differential expansion and
contraction of the piping and tanks.
11. Tanks are designed for use only in the atmospheric storage of chemicals, never for
vacuum or pressure applications.
12. Immersion heaters should never touch the walls of the tank. Minimum spacing should
be 3" - 4" from wall.
13. Refer to the chemical capability chart on this site as a guide. Be certain tank, fittings,
and fitting gasket material are compatible with chemicals at the anticipated operating
temperatures. Contact our technical staff for information on chemicals not listed, or when
uncertain conditions exist.
14. Protect tanks from impact, especially at temperatures below 40 degrees F.
15. Confined spaces must be considered hazardous. Do not enter tank without first taking
proper precautions.
16. Tank sizes as listed are nominal and calibrations on molded tanks are only
approximates, but provide an indication of volume. Polyethylene tanks expand and contract
which will effect volume. The degree in which this occurs depends on the size of the tanks,
wall thickness, specific gravity of contents, temperature of contents, and ambient
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF