Cambridge LEGACY9PCSWSQ-TN Legacy 9-Piece Patio Outdoor Dining Set with Large Square Table and 8 Swivel Rockers Instructions / Assembly

Cambridge LEGACY9PCSWSQ-TN Legacy 9-Piece Patio Outdoor Dining Set with Large Square Table and 8 Swivel Rockers Instructions / Assembly
Outdoor Furniture
STOP
IMPORTANT
If you have any problems with this product (missing or damaged parts, assembly issues, etc.),
PLEASE DO NOT RETURN TO THE RETAILER/STORE
from where you purchased the product.
Please call our Toll-Free Customer Service Hotline at:
1-800-416-3511
Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday
To expedite any future warranty claims, please retain the Instruction Sheet, Warranty
Card and receipt for future use.
Care and Maintenance
Store furniture in an upright position. Be careful to never allow water to build up in frames as this will
cause corrosion and freeze damage in cold climates. Wash all frames with a solution of mild soap and
water. Rinse with clean water and dry with a soft absorbent cloth towel. Frames can be treated with a
liquid wax for maximum protection against UV rays and/or salty, damp air. If your set includes
cushions, slings, and/or an umbrella they may be cleaned by hand with a solution of soap and water
with a clean water rinse. (Never machine wash cushions, slings or umbrella covers as this will result in
shrinkage or damage). After cleaning cushions tip on end and allow to drip dry. (Never use a
commercial or home dryer to tumble dry fabric goods). Do not use bleach or solvents to clean any
product! This will void the warranty.
Page 1
Outdoor Furniture
1-Year Limited Warranty Program
For a period of one (1) year after purchase, the Manufacturer will either repair or replace defective components in accordance with this
Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by the
original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty
revert back to the date of original purchase for future warranty.
Manufacturer or its authorized dealer can accept or reject warranty claims based on its findings. This warranty applies in normal
residential use only and is not intended for commercial use. Manufacturer can make substitutions as required of materials,
components, and sub-components of comparable value and utility. This warranty is limited to product repair or replacement (to be
determined solely by Manufacturer). Warranty return is limited to only the single affected component.
This warranty covers only manufacturing defects and does not cover normal wear and tear, damage due to acts of nature (such as, but
not limited to freezing or high winds), abuse or misuse, including chemical damage from suntan oil or other chemicals, exposure to
extreme heat or cold, abrasion or excessive weight. This product is intended to be used in standard installations only. This warranty
is invalid if the product is not used for intended purpose. Manufacturer disclaims liability for any aspect of installation and any
inconvenience caused by a defective part of a component.
Certain items are not covered by this warranty. These include, but are not limited to the following:
1. Components subjected to abuse, including abuse intended to simulate failure.
2. Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, chips, etc.).
3. Any part which merely exhibits normal wear yet functions essentially as new, including chips, scratches or stretching of
materials and stitching.
4. Tears, punctures, scratches or any damage caused by improper installation or use.
5. Damage to frames/welds resulting from improper assembly or exposure to water and/or sub-freezing temperatures is not
covered. General frame rusting is not covered.
6. Fading and/or discoloration of fabrics/cushions/straps/wicker resulting from exposure to the elements, chemicals, oils, fluids
or any other cause are not covered.
7. Umbrella bases are not covered under any circumstances.
8. Items sold “as is” or floor models.
To make a claim, call the toll-free number below. Please have available a copy of the original sales receipt along with a brief description
of the problem. Please also provide your email address and daytime telephone or cell phone #. Repairs or replacement will be made at
the Manufacturer’s option. Sales and use taxes, plus shipping and handling charges are the responsibility of the consumer.
THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES NOR IS RESPONSIBLE
FOR ANY OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THOSE OF RETAILING DEALERS. THIS
EXCLUSIVE REMEDY IS LIMITED TO RECEIPT OF A CREDIT IN CONNECTION WITH THE REPAIR OR REPLACEMENT OF ANY
PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS AS STATED IN THIS
WARRANTY. NEITHER THE PRODUCT MANUFACTURER NOR ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR INCIDENTAL,
INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
EXCEPT AS OTHERWISE MAY BE REQUIRED BY LAW, THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER
THAN THE WARRANTY DESCRIBED HEREIN, AND ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
Contact Warranty Services at
Page 2
1-800-416-3511
Care & Maintenance
Outdoor furniture can be enjoyed for many years when well maintained.
Regular Maintenance
Wash the furniture with a solution of mild detergent and water, rinse with clear water, and dry thoroughly. To all metal frames, apply a
fine, clear automobile wax for maximum protection against harmful ultraviolet exposure and salt air.
For best protection, perform this maintenance two or three times per year in low pollution areas or more frequently in high pollution
areas. Please note that these durable materials can be safely cleaned as often as desired. Note: Some suntan and sun block products
may be harmful to resin, cushions and strap, mesh and vinyl lace and strap. Do not allow such products to come in contact with any
seating surfaces to avoid deep penetrating stains, which are not covered under warranty.
How to Clean & Care for Teak Furnishings
Left alone to age, the natural color of teak furnishings will weather to a soft, silver grey. This process will take approximately nine
months, depending on the degree of sunlight and rain exposure. Imperfections, which are inherent properties of the wood, will show
over time, enhancing the beauty of the furniture. In humid or wet climates, or after rains, the wood may naturally expand and contract,
causing the grain to rise. This is to be expected with exposure to the elements and will stabilize after the initial weathering occurs.
To maintain teak furnishings, use a soft bristled utility brush and stroke lightly in the direction of the grain to remove surface dust. For
more stubborn dirt, the wood may be washed with a mild solution of four parts laundry detergent or dish washing soap to one part
bleach in water, then rinsed thoroughly and allowed to dry completely. Oiling the wood may cause mildew or irregular coloring.
How to Clean Woven Furnishings
Woven furnishings are made of durable and weatherproof extruded polyethylene resin weave. Light stains and soils may be removed
with a solution of mild detergent and water, rinsed with clear water and dried thoroughly. Mildew and heavy stains can be removed with
a quality commercial outdoor furniture cleaner and protectant. Woven furnishings may not be suitable for intensely hot climates.
How to Clean Fabric
Fine outdoor fabrics are designed to endure years of sun, soil and moisture. Wash outdoor cushions with a solution of mild detergent
and water and thoroughly rinse with clear water. Stand cushions on end and allow to air dry completely. Light stains can be removed as
above. Mildew and heavy stains can be removed with a quality commercial outdoor furniture cleaner and protectant. Note: Do not dry
clean or use a washing machine or dryer. Do not steam or use water at temperatures above 100º F when washing. Note: Be careful to
keep the outdoor furniture cleaner from contact with the cushions of your outdoor furniture, as it will cause discoloration. Do not use
bleach on printed acrylic fabrics. Do not use solvent-type materials on woven vinyl, woven blend or ultra woven blend fabrics as they
will damage the yarns. Do not use chlorine based cleaners.
How to Clean Mesh
Remove light stains with a solution of mild detergent and water, then rinse with clear water and dry thoroughly. Mildew and heavy
stains can be removed with a quality commercial outdoor furniture cleaner and protectant.
How to Clean Strap
For general or light cleaning, begin by brushing dirt off the strap. Apply a solution of mild detergent and warm water and allow it to soak
into the strap. Gently clean with a sponge or soft bristle brush, then rinse thoroughly with clear water and allow the strap to air dry.
How to Clean Vinyl Strap
Apply a quality vinyl protectant to guard against the effects of air pollution, salt air build-up, and mildew. To remove difficult stains use
rubbing alcohol applied with a soft cloth.
How to Clean & Care for Stone and Marble Tops
Tabletops are designed for normal outdoor use in residential settings. To maintain the natural beauty we recommend resealing your
table top when necessary, with the same sealer product applied during the manufacturing process. The sealer penetrates the stone
and acts as a repellent, preventing absorption of moisture and stainable materials.
If tabletop is stained with products such as wine, soda, coffee, or other colorants of organic origin, clean these spills immediately with a
mild detergent then rinse with water. In extreme cold climates, it is recommended that tabletops be stored in a dry indoor area or be
covered with suitable outdoor furniture cover. Be sure to allow space between the tabletop and the cover so that moisture does not
collect on the table; this will promote airflow and allow moisture to escape.
Page 3
ASSEMBLY INSTRUCTIONS
1
Important: We recommend 2 people work together to assemble the chair. Note the arrow labels on the "U"
bar and the rocker assembly. Also note the horseshoe shape of the rocker plate. Point the open end of the horseshoe
away from you. The arrows on the rocker assembly should be pointing towards you. Set the chair frame on the
rocker assembly with front of the seat facing you and the arrows on the "U" bar pointing towards you as shown in
Figure 1. This is very important for a safe, balanced rocking motion. If chair frame has been properly positioned
on the rocker assembly, all arrows on the "U" bar and rocker assembly will be pointing in the same direction.
2
Critical Step: The "U" metal plates must be installed in the proper location. Read this step and carefully
examine. Insert the "U" metal plate, so that the "U" bar and rocker plate are between both sides of the "U" metal
plate. Make sure that the holes in the "U" metal plate are completely aligned with the holes in the "U" bar as shown
in Figure 1. Guide the bolts through the holes on the top side of the "U" metal plate, through the holes in the "U"
bar portion of the chair, through the holes in the rocker plate and then, most importantly,through the holes in the
bottom side of the "U" metal plate. It is very important that the holes in the bottom portion of the "U" metal plate
be placed directly beneath the holes in the rocker plate. Add a spring washer and a nut to each bolt as shown in
Figure 2. Hand tighten nuts 3-4 revolutions only. Repeat the same procedure on the other side.
CAUTION: Failure to place "U" metal plates under the rocker plates and above the "U" bar exactly as
shown in diagram will cause the bolt heads and nuts to damage the structure of the rocker plates and the
"U" bar. Damage due to over tightening of bolts or improper assembly could cause injury and may void
your warranty.
ROCKER PLATE
E
A
"U" BAR
ROCKER
ASSEMBLY
Figure 1
G
C
G
"U" BAR
B
3
FOOT CAP
D
Figure 2
F
Tighten all nuts and bolts with the hex wrenches provided. Ensure the bolts are FULLY tightened. Remove
arrow labels from "U" bar and rocker assembly. Cover bolts with bolt covers.
PARTS IDENTIFICATION LIST
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS LIST
DESCRIPTION
ORDER PART # QTY
A
CHAIR FRAME
AR19238
1
B
SWIVEL BASE &
ROCKER
ASSEMBLY
AR19239
1
C
5/16" X 40 MM
BOLT
HW0295
4
D
Ø8.0 X 2.3 MM
SPRING WASHER
HW0003
4
E
"U" METAL
PLATE
HW0618
2
F
5/16" NUT
HW0015
4
G
BOLT COVER
HW0028
8
H
HEX WRENCH-1
HW0008
1
I
HEX WRENCH-2
HW0007
1
ROCKER PLATE
HW0619
FOOT CAP
FC0359
SLING TUBE CAP
FC0358
FACTORY ASSEMBLY
FACTORY ASSEMBLY
FACTORY ASSEMBLY
ASSEMBLY INSTRUCTIONS
1
Place the table top upside down on a flat, non-abrasive surface. Attach the table leg to the table top by using
the bolts and washers as shown in Fig.1. Guide the bolts through the holes in the table leg, into the pre-drilled
holes in the table top. Hand tighten only. Repeat for the other three legs.
FOOT CAP
C
G
D
F
A
2
Attach a leg to the leg connector bracket by carefully guiding the bolts already in place on the table legs (each
leg has two bolts) through the holes in the leg connector bracket. Add a washer and a nut to the end of each bolt
as shown in Fig.2. Hand tighten only. Repeat on the other three legs.
H
E
F
3
B
After making any necessary adjustments to the alignment of the table, use the hex bolt driver and hex wrench to tighten
all bolts . Note: each bolt must be tightened a few revolutions at a time. In order to apply equal pressure to all bolt
joints, we recommend working in a cross corner (X fashion). Repeat until all bolts are tight. Do not over tighten.
Over tightening may strip bolts. Cover all bolts with covers.
PARTS IDENTIFICATION LIST
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS LIST
DESCRIPTION
ORDER PART # QTY
A
TABLE TOP
AT70664
1
B
LEG CONNECTOR
BRACKET
AT70665
1
C
TABLE LEG
AT70666
4
D
1/4" X 18 MM BOLT
HW0035
8
E
1/4" NUT
HW0014
8
F
Ø6.5 X 1.0 MM
WASHER
HW0004
16
G
BOLT COVER
HW0105
8
H
NUT COVER
HW0027
8
I
HEX WRENCH
HW0009
1
J
HEX BOLT DRIVER
HW0006
1
K
TOUCH-UP PAINT
G0003
1
FOOT CAP
FC0007
UMBRELLA POLE
STOPPER & NUT
G0091
& HW0448
FACTORY ASSEMBLY
FACTORY ASSEMBLY
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement