Hanover MONDN7PCFP-BR Monaco 7-Piece Aluminum Outdoor High Dining Set with Rectangular Firepit Table and Contoured Sling Swivel Chairs Instructions / Assembly

Hanover MONDN7PCFP-BR Monaco 7-Piece Aluminum Outdoor High Dining Set with Rectangular Firepit Table and Contoured Sling Swivel Chairs Instructions / Assembly
Hanover Outdoor Furniture
IMPORTANT
If you have any problems with this product (missing or damaged parts, assembly issues, etc.),
PLEASE DO NOT RETURN TO THE RETAILER/STORE
from where you purchased the product.
Please call our Toll‐Free Customer Service Hotline at:
1‐800‐416‐3511
Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday
Or visit our website at:
www.hanover‐products.com
To expedite any future warranty claims, please retain the Instruction Sheet, Warranty
Card and receipt for future use.
For additional on‐line support on assembly, troubleshooting and care & maintenance of your outdoor
furniture, please visit our website at: www.hanover‐products.com.
6/1/2015 (a)
Outdoor Furniture
1-Year Limited Warranty Program
For a period of one (1) year after purchase, the Manufacturer will either repair or replace defective components in accordance with this
Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by the
original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty
revert back to the date of original purchase for future warranty.
Manufacturer or its authorized dealer can accept or reject warranty claims based on its findings. This warranty applies in normal
residential use only and is not intended for commercial use. Manufacturer can make substitutions as required of materials,
components, and sub-components of comparable value and utility. This warranty is limited to product repair or replacement (to be
determined solely by Manufacturer). Warranty return is limited to only the single affected component.
This warranty covers only manufacturing defects and does not cover normal wear and tear, damage due to acts of nature (such as, but
not limited to freezing or high winds), abuse or misuse, including chemical damage from suntan oil or other chemicals, exposure to
extreme heat or cold, abrasion or excessive weight. This product is intended to be used in standard installations only. This warranty
is invalid if the product is not used for intended purpose. Manufacturer disclaims liability for any aspect of installation and any
inconvenience caused by a defective part of a component.
Certain items are not covered by this warranty. These include, but are not limited to the following:
1. Components subjected to abuse, including abuse intended to simulate failure.
2. Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, chips, etc.).
3. Any part which merely exhibits normal wear yet functions essentially as new, including chips, scratches or stretching of
materials and stitching.
4. Tears, punctures, scratches or any damage caused by improper installation or use.
5. Damage to frames/welds resulting from improper assembly or exposure to water and/or sub-freezing temperatures is not
covered. General frame rusting is not covered.
6. Fading and/or discoloration of fabrics/cushions/straps/wicker resulting from exposure to the elements, chemicals, oils, fluids
or any other cause are not covered.
7. Umbrella bases are not covered under any circumstances.
8. Items sold “as is” or floor models.
To make a claim, call the toll-free number below. Please have available a copy of the original sales receipt along with a brief description
of the problem. Please also provide your email address and daytime telephone or cell phone #. Repairs or replacement will be made at
the Manufacturer’s option. Sales and use taxes, plus shipping and handling charges are the responsibility of the consumer.
THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES NOR IS RESPONSIBLE
FOR ANY OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THOSE OF RETAILING DEALERS. THIS
EXCLUSIVE REMEDY IS LIMITED TO RECEIPT OF A CREDIT IN CONNECTION WITH THE REPAIR OR REPLACEMENT OF ANY
PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS AS STATED IN THIS
WARRANTY. NEITHER THE PRODUCT MANUFACTURER NOR ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR INCIDENTAL,
INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
EXCEPT AS OTHERWISE MAY BE REQUIRED BY LAW, THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER
THAN THE WARRANTY DESCRIBED HEREIN, AND ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
Contact Warranty Services at
Page 2
1-800-416-3511
Care & Maintenance
Outdoor furniture can be enjoyed for many years when well maintained.
Regular Maintenance
Wash the furniture with a solution of mild detergent and water, rinse with clear water, and dry thoroughly. To all metal frames, apply a
fine, clear automobile wax for maximum protection against harmful ultraviolet exposure and salt air.
For best protection, perform this maintenance two or three times per year in low pollution areas or more frequently in high pollution
areas. Please note that these durable materials can be safely cleaned as often as desired. Note: Some suntan and sun block products
may be harmful to resin, cushions and strap, mesh and vinyl lace and strap. Do not allow such products to come in contact with any
seating surfaces to avoid deep penetrating stains, which are not covered under warranty.
How to Clean & Care for Teak Furnishings
Left alone to age, the natural color of teak furnishings will weather to a soft, silver grey. This process will take approximately nine
months, depending on the degree of sunlight and rain exposure. Imperfections, which are inherent properties of the wood, will show
over time, enhancing the beauty of the furniture. In humid or wet climates, or after rains, the wood may naturally expand and contract,
causing the grain to rise. This is to be expected with exposure to the elements and will stabilize after the initial weathering occurs.
To maintain teak furnishings, use a soft bristled utility brush and stroke lightly in the direction of the grain to remove surface dust. For
more stubborn dirt, the wood may be washed with a mild solution of four parts laundry detergent or dish washing soap to one part
bleach in water, then rinsed thoroughly and allowed to dry completely. Oiling the wood may cause mildew or irregular coloring.
How to Clean Woven Furnishings
Woven furnishings are made of durable and weatherproof extruded polyethylene resin weave. Light stains and soils may be removed
with a solution of mild detergent and water, rinsed with clear water and dried thoroughly. Mildew and heavy stains can be removed with
a quality commercial outdoor furniture cleaner and protectant. Woven furnishings may not be suitable for intensely hot climates.
How to Clean Fabric
Fine outdoor fabrics are designed to endure years of sun, soil and moisture. Wash outdoor cushions with a solution of mild detergent
and water and thoroughly rinse with clear water. Stand cushions on end and allow to air dry completely. Light stains can be removed as
above. Mildew and heavy stains can be removed with a quality commercial outdoor furniture cleaner and protectant. Note: Do not dry
clean or use a washing machine or dryer. Do not steam or use water at temperatures above 100º F when washing. Note: Be careful to
keep the outdoor furniture cleaner from contact with the cushions of your outdoor furniture, as it will cause discoloration. Do not use
bleach on printed acrylic fabrics. Do not use solvent-type materials on woven vinyl, woven blend or ultra woven blend fabrics as they
will damage the yarns. Do not use chlorine based cleaners.
How to Clean Mesh
Remove light stains with a solution of mild detergent and water, then rinse with clear water and dry thoroughly. Mildew and heavy
stains can be removed with a quality commercial outdoor furniture cleaner and protectant.
How to Clean Strap
For general or light cleaning, begin by brushing dirt off the strap. Apply a solution of mild detergent and warm water and allow it to soak
into the strap. Gently clean with a sponge or soft bristle brush, then rinse thoroughly with clear water and allow the strap to air dry.
How to Clean Vinyl Strap
Apply a quality vinyl protectant to guard against the effects of air pollution, salt air build-up, and mildew. To remove difficult stains use
rubbing alcohol applied with a soft cloth.
How to Clean & Care for Stone and Marble Tops
Tabletops are designed for normal outdoor use in residential settings. To maintain the natural beauty we recommend resealing your
table top when necessary, with the same sealer product applied during the manufacturing process. The sealer penetrates the stone
and acts as a repellent, preventing absorption of moisture and stainable materials.
If tabletop is stained with products such as wine, soda, coffee, or other colorants of organic origin, clean these spills immediately with a
mild detergent then rinse with water. In extreme cold climates, it is recommended that tabletops be stored in a dry indoor area or be
covered with a suitable outdoor furniture cover. Be sure to allow space between the tabletop and the cover so that moisture does not
collect on the table; this will promote airflow and allow moisture to escape.
Page 3
ASSEMBLY INSTRUCTIONS
1
Position the swivel base on a flat, solid surface. Make sure the swivel plate is positioned all the way into
the base. It may have vibrated out during shipment. The two sets of holes in the swivel plate should be
facing away from you.
Note the arrows on both the swivel plate and the "U" bar portion of the chair frame. Position the chair frame
onto the swivel plate so that the two pairs of holes in the "U" bar are exactly aligned with the two pairs of
holes in the swivel plate and the arrows on both the "U" bar and swivel plate are pointing in the same
direction. Proper positioning of the chair frame on the swivel plate/swivel base assembly, and proper
alignment of the holes in the "U" bar with the holes in the swivel plate are critical to the safe, well balanced
swiveling motion of the chair.
2
3
Carefully examine the diagram. Attach a metal plate to two (2) bolts and guide the bolts through the top of
one set of holes in the "U" bar (located at the bottom of the chair frame) and into the pair of holes in the
swivel plate. From beneath the swivel plate, add a washer, then a spring washer and a nut to the end each bolt.
Hand tighten 3-4 revolutions only. Do not tighten completely. Repeat procedure for pair of holes on the
opposite side.
Using the hex wrenches provided, tighten the nuts and bolts. Be sure the bolts are fully tightened. Remove
the arrow labels from the “U” bar and swivel plate. Your chair is now ready for use.
A
C
E
"U" BAR
SWIVEL PLATE
B
G
D
F
Page 4
PARTS IDENTIFICATION LIST
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS LIST
DESCRIPTION
ORDER PART # QTY
A
CHAIR FRAME
AB1296
1
B
SWIVEL
ASSEMBLY & BASE
AB1297
1
C
5/16" X 43 MM
BOLT
HW0450
4
D
Ø8.0 X 2.3 MM
SPRING WASHER
HW0003
4
E
METAL PLATE
HW0847
2
F
5/16" NUT
HW0015
4
G
Ø8.5 X 1.5 MM
WASHER
HW0005
4
H
HEX WRENCH-1
HW0008
1
I
HEX WRENCH-2
HW0007
1
FOOTREST COVER
FACTORY ASSEMBLY
G0155
FOOT CAP
FACTORY ASSEMBLY
FC0030
ADV14011
Page 5
ASSEMBLY INSTRUCTIONS
CSA Model 98300
ARV08300
Installer: Leave these instructions with consumer.
Consumer: Keep these instructions for future reference.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or fire department.
WARNING:
Improper installation, adjustment alteration,
service or maintenance can cause injury or
property damage. Read the installation,
operating and maintenance instructions
thoroughly before installing or servicing this
equipment.
WARNING: For Outdoor Use Only
WARNING
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
DANGER
FOR USE WITH 20LB (9KG) PROPANE
CYLINDER WITH TYPE 1 CONNECTION OR FOR
USE WITH NATURAL GAS AFTER CONVERSION
KIT IS INSTALLED (MUST BE PROFESSIONALLY
INSTALLED).
CARBON MONOXIDE HAZARD
This appliance can produce carbon
monoxide which has no odor.
Using it in an enclosed space can kill
you.
Never use this appliance in an enclosed
space such as a camper, tent, car or
home.
Questions, Problems, Missing Parts? Before returning to
your retailer, call our customer service department in the
US and Canada at 1-800-416-3511, Monday-Friday, 9 a.m.–
5 p.m. Eastern Time.
1
Dec-01-2016
WARNING:
USE FACTORY APPROVED
REPLACEMENT PARTS AND
ACCESSORIES ONLY. USE
OF UNAPPROVED PART OR
ACCESSORIES CAN VOID
THE WARRANTY ON THIS
PRODUCT AND RESULT IN
AHAZARDOUS CONDITION.
PLEASE CONTACT US FOR
INFORMATION REGARDING
REPLACEMNT HOSES,
THERMOCOUPLES,ELECTR
ODES,IGNITION
MODULES,LAVAROCKS,LO
GS, FIRE ICE, ETC.
TABLE OF CONTENTS
Important Safety Information
3
Important About Propane
4
Specification
4
Parts Identification List
5-6
Installation
7-11
Natural Gas Conversion
12
Lighting Instructions
13
Batteries
14
Maintenance
14
Troubleshooting Guide
15
Warranty
16
2
IMPORTANT SAFETY INFORMATION
The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural Gas and Propane Installation Code,
CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable.
The appliance and its appliance main gas valve must be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).
The appliance must be isolated from the gas supply piping system by closing its equipment shutoff valve
during any pressure testing of the gas supply system at test pressure equal to or less than 1/2 psi (3.5kPa).
The appliance area must be kept clear and free from combustible materials, gasoline and other flammable
vapors and liquids.
Do not use this appliance if any part has been under water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control system and any gas control which has been under
water.
Children and adults should be alerted to the hazards of high surface temperatures and kept at a safe
distance to avoid burns or clothing ignition.
Young children should be carefully supervised when they are anywhere near the appliance.
Clothing or other flammable material should not be hung from the appliance, or placed on or near the
appliance.
Any screen or guard removed for servicing an appliance must be replaced prior to operating the
appliance.
Installation and repair should be done by a qualified service person. The appliance should be
inspected before use and at least annually by a professional service person. More frequent cleaning
may be required as necessary. It is imperative that the control compartments, burners and circulating
air passageways of the appliance be kept clean.
Do NOT burn solid fuels in this gas fireplace.
Do NOT ignite the burner before pouring all of the burner media (lava rock or fire ice) into the burner pan. The
media must be evenly distributed over the burner.
During initial firing of firepit, please stay away from the firepit for 20 minutes as fire media (lava rock or fire ice)
may pop and hit someone on the face or eyes
Do NOT ignite or use the firepit if the burner media (lava rock or fire ice) are wet. Ensure the burner media are
completely dry before igniting as intense heat could cause the media to crack and pop.
It is UNSAFE to use this product for cooking!
CAUTION: The propane gas pressure regulator provided with this appliance must be used. This regulator is
set for an outlet pressure of 11 inches water column.
This outdoor gas appliance is not intended to be installed in or on recreational vehicles and/or boats.
Before each use of this gas appliance, open the LP (Liquid Propane) Tank Drawer and inspect the LP Hose. If
there is evidence of excessive abrasion or wear, or the hose is cut, it must be replaced prior to the gas
appliance being put into operation. Use only the replacement hose assembly specified in this manual. Inspect
the burner before each use of the appliance. The burner must be replaced prior to the appliance being put
into operation if it is evident that the burner is damaged. Use only the burner listed in these instructions.
Keep the fuel supply hose away from any heated surfaces.
3
IMPORTANT SAFETY INFORMATION
ABOUT PROPANE (LP) GAS
A self contained LP-gas cylinder for use with this appliance must have a
capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD
(overfill protection device). See Figure 1.
The LP-gas supply cylinder to be used must be constructed and marked in
accordance with the specification for LP-gas cylinders of the U.S. Department
of Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339,
Cylinder, Sphere and Tubes for the Transportation of Dangerous Goods.
 The cylinder supply system must be arranged for vapor withdrawal.
 The cylinder used must include a collar to protect the cylinder valve.
 This appliance shall be used only outdoors in a well-ventilated space and
shall not be used in a building, garage or any other enclosed space.
 When this appliance is not is use, the gas must be turned off at the supply
cylinder.
 Storage of this appliance indoors is permissible only if the cylinder is
disconnected and removed from the appliance.
 Cylinders must be stored outdoors in a well-ventilated area out of the
reach of children .Disconnected cylinders must have threaded valve plugs
tightly installed and must not be stored in a building, garage or any other
enclosed areas.
CSA (Canadian Standards Association) certified to ANSI Z21.97-2014 / CSA
2.41-2014 “ Outdoor Decorative Gas Appliances”
Figure 1
SPECIFICATIONS
INPUT
Propane Regulator
Pressure
Natural Gas Minimum
Inlet Pressure
Clearances to
combustible surfaces
30,000 Btu/hr
11 in / 2.74 kPa water
column
7 in / 1.74 kPa water
column
Sides 24 in / 60.96 cm
4
20,000 Btu/hr Low fire
Top: 72 in / 182.88 cm
PARTS IDENTIFICATION LIST
PART
DESCRIPTION
PART#
QTY
A
CONTROL KNOB
FP0245
1
B
GAS VALVE
FP0307
1
C
THERMOCOUPLE
FP0004
1
D
LP REGULATOR HOSE
FP1329
1
E
ELECTRODE
FP1330
1
F
GAS TUBE
FP1689
1
G
ORIFICE ELBOW
FP1385
1
H
IGNITION MODULE
FP1666
1
I
ORIFICE BRACKET
FP1667
1
J
PROPANE ORIFICE
FP1299
1
K
NATURAL GAS ORIFICE
FP1300
1
L
“AAA” BATTERY(1.5V)
HW0705
1
M
FOOTCAP
FC0660
4
N
HEX BOLT DRIVER
HW0006
1
O
1/4" X 20 MM BOLT
HW0036
8
P
1/4" X 30 MM BOLT
HW0038
8
Q
WASHERS
HW0004
14
R
BIG WASHERS
HW0594
4
S
FIREPIT TABLETOP
FP1749
1
5
T
MIDDLE PANEL
FP1750
1
U
BOTTOM PANEL
FP1751
1
V
BACK PANEL
FP1752
1
W
DOOR PANEL
FP1753
1
Y
BURNER COVER
FP1754
1
Z
BURNER COVER
PROTECTIVE RING
FP1755
1
AA
FIREPAN/BURNER
ASSEMBLY
FP1756
1
BB
SUPPORT BAR-1
FP1757
1
CC
SUPPORT BAR-2
FP1758
1
6
INSTALLATION
1. Identify parts packed in carton against the parts list. Remove all protective
materials and set parts on a flat, non-abrasive surface.
IMPORTANT NOTE: WE RECOMMEND TWO PEOPLE WORK TOGETHER
TO ASSEMBLE THE PRODUCT.
2. Place the back panel upside down on a flat, non-abrasive surface. Open it
as shown in Figure 2.
Figure 2
3. Assemble the door panel to the back panel as shown in Figure 3.
Figure 3
7
4. Attach the bottom panel to legs by using four 1/4"x30 mm bolts and washers
as shown in Figure 4.Guide the bolts through holes in the bottom panel, into
pre-drilled holes in the legs. Hand tighten only.
Figure 4
5. Carefully place the middle panel inside back panel with bottom panel as
shown in Figure 5.
Figure 5
8
6. Attach the bottom panel to the back panel by using two 1/4"x30 mm bolts
and washers as shown in Figure 6. Guide the bolts through holes in the bottom
panel, into pre-drilled holes in the back panel. Hand tighten only.
Figure 6
7. Attach the two support bars to the firepan/burner assembly by using two
1/4"x30 mm bolts and washers as shown in Figure 7. Hand tighten only.
Figure 7
8. Attach the complete firepan/burner assembly to back panel with door panel
by using four 1/4"x20 mm bolts and washers as shown in Figure 8. Hand
tighten only.
Figure 8
9
9. After making any necessary adjustments to the alignment of the all parts,
use the hex bolt driver to tighten all bolts. Do not over tighten. Over tightening
may strip bolts.
10. With the help of another person, Attach the table top to the complete base
by using four 1/4"x20 mm bolts and washers as shown in Figure 9. Guide the
bolts through the holes in the side panels, into the pre-drilled holes in the table
top. Do not tighten completely. Carefully place the burner cover protective ring
inside table top.
Figure 9
11. Open the tank door, place the tank in the holder and connect the regulator
as shown in Figure 10. Turn the black handle clock-wise to tighten. Turn the
handle counter-clockwise to remove. The hose must point down. Open the
control door and check that the valve is turned all the way clockwise to the
“OFF” position. Open the tank valve. Apply a solution of soapy water to the
tank-regulator connection and to the valve-hose connection to check for leaks.
If soap bubbles continue to form, the connection has a leak. If a leak is found,
close the tank valve and tighten all connections. NEVER USE A FLAME TO
CHECK FOR LEAKS.
Figure 10
10
12. Tighten threaded knobs (L) found on tank tray (Figure.11) so that the LP
tank cannot move from side to side. Do not remove plastic cap from end of
threaded section.
Figure 11
13. Pour the lava rocks (not included) into the burner pan completely covering
the burner. See Figure 12.
BURNER PAN
IGNITION WELL
Figure 12
14. Remove the cardboard cover from the ignition well as shown in Figure 12.
Remove any lava rock or fire ice on top of ignition well.
Figure 13
CARDBOARD COVER
15. Open the tank valve. Apply a solution of soapy water to the tank-regulator
connection and to the valve-hose connection to check for leaks as shown in
Figure 14. If soap bubbles continue to form, the connection has a leak. If a leak
is found, close the tank valve and tighten all connections.
NOTE: NEVER USE A FLAME TO CHECK FOR LEAKS.
Checking the tank-regulator for leaks
Figure 14
11
NATURAL GAS CONVERSION
Natural gas conversion must be performed only by your natural gas provider or
service company.
Step 1- At the control panel, disconnect the rubber gas hose from the gas valve.
Step 2- Below the burner, disconnect the aluminum gas tube from the orifice elbow.
Step 3- Remove the 2 M4 nuts from the orifice holder and remove the orifice bracket
assembly.
Step 4- Disconnect the orifice from the elbow and replace it with the Natural Gas orifice
from the kit.
Re-fit the orifice bracket assembly onto the holder using the 2 M4 screws and nuts.
Re-connect the aluminum gas tube into the end of the elbow. Connect your Natural Gas
supply line onto the gas valve at the control panel. BEFORE ATTEMPTING TO USE THE
FIREPIT, check ALL of the connections for leaks using a solution of soapy water. If a leak
is discovered and any bubbles are seen, close the main gas valve and re-tighten ALL the
connections. NEVER USE A FLAME TO CHECK FOR GAS LEAKS!
12
Step 5- Stick the conversion label on the rating plate as shown in Figure 15.
Metal Rating Plate
Serial Number _________________
Model Number: 98900
1. must be used. This regulator is set for an outlet pressure of
CAUTION: The gas pressure regulator provided with this appliance
2.
This appliance has been converted to use Natural Gas.
3. Input 40,000 Btu/hr.
Max Gas Supply Pressure 7 inch w.c. (1.74 kPa) Min.
4. Gas Supply Pressure 5 inch w.c. (1.24 kPa)
5.in.609 mm. Top 72 in. 1828 mm.
Minimum clearance from combustible constructions: Sides: 24
FOR OUTDOOR USE ONLY. If stored indoors, detach and6.
leave cylinder outdoors.
7.
Figure 15
Conversion Label
LIGHTING INSTRUCTIONS
Warning: If these instructions are not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
1. Make sure the control knob is in the "OFF" position. See Figure 16 Open the
tank
valve all the way.
IGNITER BUTTON
CONTROLKNOB
Figure 16
2. Push in the igniter button. You will hear a slight clicking sound. With the
igniter button pushed in, push and turn the control knob to the “ON” position.
the fire should light within a few seconds. Once the flame is lit, release the
igniter button and continue to hold the
13
control knob in for 10 to 15 seconds. Release the control knob. The control
knob should pop back out and then remain lit.
Note: If the fire does not light, turn the knob to the “OFF” position and wait five
(5) minutes before trying again.
3. To turn down the flame, push the control knob in slightly and turn to Medium
(medium
or Low (small flame).
4. To shut down the fire pit, turn the control knob to the “OFF” position and turn
off the tank valve.
BATTERIES
Make sure the control knob is in the "OFF" position.
Unscrew the push button cap on the ignition module
located on the control panel to access the battery
compartment. The ignition module requires one Alkaline
AAA size battery (1.5V). The negative (-) end goes in
first. See Figure 17. Dispose of battery safely. May
explode or leak if charged or disposed of in fire. Make
sure of the polarity. Mercury and cadmium free
Figure 17
Always purchase the correct size and grade of battery most suitable for the
intended use. Replace all batteries of a set at the same time. Clean the battery
contacts and also those of the device prior to battery installation. Ensure
batteries are installed correctly with regard to polarity (+ and -). Remove
batteries from equipment which is not to be used for an extended period of time.
Remove used batteries promptly.
MAINTENANCE
The flames should look like those in Figure 18. To clean the burner, use a soft
brush after the burner has cooled completely. Never use a vacuum cleaner on
the burner. It is recommended that the fire pit be stored indoors during the winter
if it will be subjected to freezing temperatures. The LP cylinder must be
disconnected and removed from the appliance before the appliance can be
stored indoors.
Figure 18
14
TROUBLESHOOTING GUIDE
PROBLEM
CAUSE
REMEDY
No Propane Gas at Burner
Check that gas tank valve is open. Turn
control knob to “ON” and push control
knob in. Make sure tank has propane
gas.
Check that AAA battery is installed with
negative (-) end first and has a charge.
Check that the wire is connected to the
ignition module. Check that the
electrode is not cracked or broken.
Burner won’t light
No Spark at Electrode
Burner won’t stay
lit after lighting
Lack of oxygen
Remove excess lava rocks or fire ices
from around the ignition well.
Thermocouple not in flame
Check that the tip of the thermocouple is
even with the top of the ignition well.
Remove any lava rocks from the ignition
well.
Thermocouple connection
at the main control valve is
loose
Tighten the thermocouple nut at the
back of
the valve.
No Lava Rocks on Burner
Cover the burner with lava rocks per the
instructions
15
ONE-YEAR LIMITED WARRANTY
What is Covered Under This Warranty?
The item you have purchased is warranted against defects in material and workmanship
for the following parts from the date of purchase for the period of warranty as outlined
below, but only when the unit is installed and operated in accordance with the instructions
in this Owner’s Manual and in compliance with local building and fire codes:
Limited 1 Year
• Stainless Tube/Plate burner
Limited 90 days
• All remaining parts
How Do I Obtain Warranty Service?
To obtain warranty service, you must contact our customer service center within the
relevant warranty period and provide us with a copy of your dated register receipt as proof
of the purchase date. We reserve the right to request photographs and/or return of the
defective item(s) and/or such other evidence relating to any claim as we shall reasonably
require.
What are the Limitations and Exclusions of this Warranty?
Warranty Limitations:
This warranty is subject to the limitation set forth above. In addition, this warranty is made
to the original purchaser only and is effective only if items are purchased from one of our
authorized dealers. This warranty is not transferable. For warranty replacements based on
warranty claims, we will not be responsible for charges associated with shipments outside
continental North America at any time or for any reason.
Warranty Exclusions: This warranty is subject to the exclusions set forth above. In addition,
the following are excluded from coverage under this warranty: any item used for
commercial, contract or any other non-residential purpose; clearance items, display
models or items purchased “as is”; freight damage; items subject to misuse, abuse,
neglect or lack of proper care or maintenance (including without limitation as provided in
any “care and maintenance guide” or similar information we provide); normal wear and
tear; damage caused by acts of nature, acts of force majeure, vandalism, fire or other
casualty, or improper assembly; hardware against corrosion or rusting; purchased or
replacement parts; and all plastic parts. Also excluded are loss of use or time;
inconvenience; money; travel; packaging; or incidental, special or consequential damages
of any kind. Replacement of defective items or parts as provided herein, or (at our sole
discretion) pro rated refund of your purchase price, shall constitute your sole and
exclusive remedy for items which are not as warranted. In no event shall our responsibility
exceed the purchase price of the item found to be other than as warranted. This warranty
is the exclusive statement of your rights with respect to items you have purchased and
supersedes any other express warranty or statement, written or oral, made in connection
with the purchase and sale of such items. The term ”item” when used herein in the
singular refers to the specific piece found to be defective, and not to the entire set of which
the item is a part.
Some states do not allow exclusion or limitation of incidental or consequential damage, so
that limitation may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights that vary from state to state.
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement