ANZZI KAZ33201A-GD13 Elysian Farmhouse Stainless Steel 32 in. Single Bowl Kitchen Sink Installation instructions

 MEDUSA
ANZZI | WASTE DISPOSAL
Оса они ВВ
LISTED
(=)
5
INSTALL MANUAL
SIMCORP
LUXURY HOME BRANDS
FOOD WASTE DISPOSER
Safety Information Owner's Manual
Connecting Electricity.................. 2,3
Safety Precautions................c........2 & Installation
Instructions
Installation Instructions
Attaching the Discharge
PR
Components and Installation
of Sink Flange........——e—.—.eceeeeevevceoa 5
Connecting Disposer to
Sink Flangée...... . o ececcrcierc nes F
Dimensions, Typical
INStallaNONES oO
Dishwasher Connection.................. 6
Operating Instructions
Care and Maintenance .................. 10
Continuous Feed Models................. 8
Troubleshooting Tips
Before You Call for
Service.........eeececcerecereoeer eres "0. 11
Write the model and serial numbers
for your Disposer here:
Model #
Serial #
You can find them on a label on
the bottom of the disposer.
A=
Е
|=
[am]
=
uv
=
|
—
©
тн
[=
в
Far)
a
Че
За
Installation Instructions
Operating Instructions
Troublesshooting Tips
Customer Service
IMPORTANT SAFETY INSTRUCTIONS.
READALL INSTRUCTIONS BEFORE USING.
INSTRUCTIONS PERTAINING TO ARISK OF FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS
N
~~
LE
AWARNING!
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
» 5. Use this appliance only for its intended
purpose as described in the owner's manual.
un Read allthe instructions before using the
appliance,
m To reduce the risk of injury, close supervision
is required when an appliance is used near
children.
m Do nol put fingers or hands inlo a waste
disposer.
E Turn the electrical switch connected to the
disposer to the off position before attempting to
clear a jam or remove an object from Ihe
disposer.
n When attempting to loosen a jam in a waste
disposer, use long wooden object such as a
wooden spoon or the handle of a broom or mop.
ms When attempting to remove objects from a
waste disposer, use long-handled tongs or
pliers. If the disposer is magnetically actuated,
use only nonmagnetic tools.
m To reduce the risk of injury by materials that
may be expelled by a waste disposer, do not
put the following into a disposer:
a) Clam or oyster shells.
b) Caustic drain cleaners or similar products.
c) Glass, china or plastic,
d) Large whole bones.
e) Metal, such as bottle caps, tin cans, utensils
or aluminum foil.
f) Hot grease or other hot liquids.
g) Whole corn husks.
m [his appliance must be installed by the local
authority or the national authority. Do nol
disassemble for any reason when the
appliance is installed. There are no serviceable
parts.
AWARNING!
ms When not operating a disposer, leave the drain
stopper in place to reduce the risk of objects falling into
the disposer.
E The appliance must be installed so that resel bulton
is readily accessible.
m This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a
person responsible for their safety. Children should be
supervised to ensure lhey do nol play with the
appliance.
m If the supply cord is damaged, it musi be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
= Make sure that the installation of this appliance is
allowed by the authorities.
m This marking indicates that this product should not be
disposed wilh other household wastes throughout the
EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device,
please use the return and collection
systems or contact the retailer where
the product was purchased. They
can take this product for
environmental safe recycling. НН
m For proper grounding instructions see the
ELECTRICAL CONNECTION portion of this manual.
m Never use this appliance in damp location (eq.
bathroom or laundry room).
m Do not use this appliance to dispose of hard materials
such as glass and metal.
n Switch off or unplug the appliance before attempting
to free a jammed rotor with an implement.
С) HOW TO CONNECT ELECTRICITY
\
If you are not familiar with electrical power and procedures, call a qualified electrician.
DANGER: improper connection of the
equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician
or serviceman if you are in doubt as to whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance if it will not fit the
outlet; have a proper outlet installed by a qualified
electrician.
These appliances are meant forhousehold use
only. De not use for commercial application.
Ma
For Models Equipped with a Grounded Cord:
GROUNDING INSTRUCTIONS: This appliance must
be grounded. In the event of a malfunction or
breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of
electric shock. This appliance is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
IMPORTANT SAFETY INSTRUCTIONS.
READ ALL INSTRUCTIONS BEFORE USING.
A WARNING!
HOW TO CONNECT ELECTRICITY (cont.)
ef
If you are not familiar with electrical power and procedures, call a qualified electrician.
The power cord and/or connections mustcomply Trace lead connected to this
with the National Electrical Code, Section 422
andfor local codes and ordinances.
For Models Not Equipped with a Cord:
1. Attach a power cord, minimum 138" in length
and not to exceed 36" in length.
2. Wire the disposer directly into the house
currant.
3. Make sure the switch shall be easily visible
and accessible. The recommend distance
between this appliance and electrical switch is
within 2m.
To Attach a Power Cord:
GROUNDING INSTRUCTIONS: This
appliance must be grounded. In the event of
malfunction or breakdown, grounding provides a
path of least resistance for electric current to
reduce the risk of electric shock. The power cord
(to be installed) must have an equipment-
grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet
that is properly installed and grounded in
accordance with all local codes and ordinances.
DA N G E R « Improper connection of the
equipment-grounding conductor can resultin a
risk of electric shock. Check with a qualified
blade and attach that lead to
white wire on disposer.
Ribber side
NOTE: When viewing
face of electrical plug
with grounding pin
al top. the lell blade
is connected to the
identified wire.
Strain Relief
C. Use a cable clamp strain
relief connector where
power cord enters the
disposer.
Mul
To Wire Your Disposer Directly into
the House Current:
GROUNDING INSTRUCTIONS: This
appliance must be connected to a grounded, metal,
permanent wiring system; or an equipmentgrounding
conductor must be run with the circuit conductors and
connected to the equipmentgrounding terminal or lead
on the appliance.
A. If you use BX cable:
electrician or serviceman if you are in doubt as to !- These products are designed for household use.
whether the appliance is properly grounded.
NOTE:
Disconnect electric power fo disposer circuit
2. Connect line wire to blue lead of disposer with a wire
nut. Connect neutral wire to brown lead of disposer
with a wire nut. Connect bare ground wire to the
before installation. Turn the circuit breaker to the round screw. The ground wire should be clamped and
OFF position or remave the fuse.
A. Connect the disposer to 110-120 Volt, 60 Hz
AC current only,
B. If a plug-in cord is used, use a three-prong
plug. Ground wire should be attached to the
ground screw in the bottom of the disposer (end
bell),
held by a strain relief.
3. Do not use a rigid conduit for the wiring connection.
4. A dedicated acceptable motor switch, with the off
position marked, shall be provided for this disposer at
the time of installation. The switch shall be mounted in
sight of the disposer or the sink opening for the
disposer.
If BX cable is not used, provide a separate ground wire
to nearest reliable ground, using the screw in the end
bell for the ground wire.
Red Resel Bulton
Ground Screw
у A wire Nut
To House Current F
or Power Cord —
Bottom ofthe WW Remove
Disposer (end bell) Bottom Cap
Ее
o
per
ru
=
i)
4
&c
Le
+
Lar
Gi
mm
“a
Installation Instructions
Operating Instructions
Troublesshooting Tips
Customer Service
E
a]
pur
ar
=
|
pe
©
u—
[==
=
+
®
ee
lan)
0)
Installation Instructions
Operating Instructions
Troublesshooting Tips
Customer Service
IMPORTANT SAFETY INSTRUCTIONS.
READ ALL INSTRUCTIONS BEFORE USING.
A WARNING!
[Fi HOW TO CONNECT ELECTRICITY (cont.)
& 1
If you are not familiar with electrical power and procedures, call a qualified electrician.
SOME TYPICAL ELECTRICITY CONNECT
If your kitchen had a wall outlet with a control switch If your kitchen wall outlet didn't have a control switch, you can
yet, please plug the power cord of disposerintothe buy a external air switch from us or from market, the switch
outlet directly. should have a CE certification if you buy from market. Please
connecl your disposer power cord lo the air swilch according
to below method.
A Cone Swilch
Ar Switch Button
wall Outlet Air Switch
Disposer ;
Disposer
Wall Outlet
vil,
o AND FOLLOW THIS SAFETY INFORMATION CAREFULLY
N SAVE THESE INSTRUCTIONS
-4-
Installation
Instructions
Disposer
BEFORE YOU BEGIN
Read these instructions completely and carefully
» IM PORTANT = Save these instructions for
local inspector's use.
. IM PORTANT = Dbserve all governing codes
and ordinances.
« Note to Installer - Be sure lo leave these
instructions with the Consumer.
« Note to Consumer - Keep these instructions for
future reference.
= Skill Level - Installation of this appliance requires
basic mechanical skills.
» Completion Time - 1 hour.
s Proper installation is the responsibility of the installer.
PREPARATION
1. Disconnect electrical power supply to disposer.
2. Remove old disposer or sink lange assembly.
3. Inspect drain line. If it is heavily coated with hardened
grease and accumulations, roul oul with a plumber’s
snake.
4. Remover old sealing materials and gasketing from
sink opening, both top and bottom.
NOTE: Top and bottom of sink surfaces must be free of
any materials to prevent leaks.
-5-
WHAT YOU WILL NEED
es
Phillips and flat blade screwdrivers
SEEN
Channel lock pliers, slip joint
E C—0
Nut driver
Hammer
ADDITIONAL MATERIALS YOU MAY
NEED
. Steel punch or wooden dowel
Petroleum jelly or liquid soap
Hose clamp
Dishwasher drain connector
Adjustable pipe wrench
Plumber's pully (for cast sinks)
Stepped rubber drain adapter
Wire nuits
. Cable connector
10. Flexible drain pipe
11. Power cord kit
D A OH ds Ld Rha
wo
Installation Instructions
COMPONENTSAND INSTALLATION
COMPONENTS
Stopper
OO
Removable
lash Guard
Qs Sp
a an Sink Flange
Rubber Sink
< 4— Flange Gasket
| Je Sink
Sink Flange
Assembly
@Æ — Fiber Gasket
Support Ring
CD
(Note Arrows
Tightening
Indicating Up)
Ears Y =
II 1 f—— Mount Ring
Cushion Mount
__ ©... (Note TOP Mark}
E nen Discharge Inlet
Elbow Flange
Screw
A oe
Disposer— Hopper Discharge
Elbow
Elbow Gaskel
End Bell Rating Label in This Area
(Electrical Connections)
INSTALLATION OF SINK FLANGE
(Read completely before starting.)
Correctly Installed Sink Flange
Sink Flange ~~ Rubber Gasket
Fiber Gasket — Pr Emam Support Ring
Bottom Bead of
Cushion Mount
ee
r к
CS
Open Area
No Obstruclion
Groove Mounting Ring
Cushion weil =
should be free
Bottom Bead
to move up and down
{Shown for proper orientation)
Sink Flange
-6-
NOTE: Pay close altenlion lo the order of the sink flange
parts, as they have been correctly assembled by the
factory.
A. Disassemble the sink flange assembly from the
disposer by turning the mount ring to the left (clockwise)
and removing it.
B. Raise the mount ring toward the top of the sink flange.
Remove the cushion mount and the mount ring. You may
want to practice installing the cushion mount at this point
before you are under (he sink.
C. Unscrew the support ring from the sink flange and
remove the fiber gasket. You are now left with the sink
flange and the rubber gasket.
D. The rubber gasket is used instead of plumbers
putty with stainless steel sinks. Some cast sinks will
require putty.
E. If no pulty is used, insert the sink flange through the
rubber gasket into the sink opening. Do not turn the
flange once itis seated.
F. If you use putty instead of the gasket, form a ring
around the underside of the sink flange. Insert the flange
into the sink opening, press down hard to squeeze out
excess putty. From under the sink, trim off excess putty
flush with the bottom edge of the sink opening.
G.From underneath the sink, slip the fiber gasket onto
the exposed sink flange. With arrows pointing up, screw
the support ring onto the sink
flange and hand tighten until
the sink flange will not move.
At this point you may want to
insert the stopper in the sink
and fill with water to check
the sink flange seal and insure there are no leaks.
H.Place the mount ring over the sink flange and hold in
place while installing the cushion mount (large side
down). Make sure the groove on the inside of the cushion
mount fits over the lip on the
sink flange, similar to putting
the on a plastic container. Run
your fingers around the entire
cushion mount with slight
pressure. Do not press too
hard. When the cushion
mount is properly seated,
the mount ring can be
pulled downward over the
cushion mount and will be
free to turn.
Hand-tighten sink flange
Cushion Mount Detail
Groove Top
Bottom Bead x
Installation Instructions
DISHWASHER CONNECTION (IF REQUIRED)
If you are connecting to a dishwasher, complete the following
slep. If a dishwasher is not to be connected go on lo
"Allaching the Discharge Elbow" seclion.
[Al KNOCK OUT PLUG
Using a blunt instrument (steel punch orwooden
dowel), knock out entire plug. Do nol use a screwdriver
or sharp instrument. When knockout plug falls into
disposer, you may remove it or simply grind it up when
the disposer is used. This will not damage the
disposer in any way, but may take some time to grind,
over the course of several uses.
Ce
— Knock out plug
Ls
3
ATTACHING THE DISCHARGE ELBOW
CONNECT DISCHARGE ELBOW"
Connect the discharge elbow to the disposer.*™
Make sure all plumbing connections are tight.
Rubber
7
Fal
рва аа
Elbow
[2l CONNECT HOSE
Connect the dishwasher hose using a hose clamp. If
the hose size is different, you will need a stepped
rubber adapter.
Hose Clamp Stepped Rubber Adapter
* Discharge elbow must be installed by a professional.
“* Some installations (see page 8 for examples) may
require the use of a flexible drain pipe.
NOTE: If the dishwasher connection is made without
removing the plug, the dishwasher may overflow.
Installation Instructions
CONNECTING DISPOSER TO SINK FLANGE
[1] ATTACH TO SINK FLANGE
Line up the disposer
Mount
under the sink flange. Ring Slot
Guide the hopper
projections into the Hopper
mount ring slots. Turn Projectio
the mount ring about
1/4" Lo the right so thal
the disposer is
temporarily supported.
LINE UP WITH OUTLET PIPE
Turn the mount ring and the disposer until the
disposer discharge elbow lines up with the outlet
pipe(See page 9).
Outlet pipe
Discharge
Elbow
[3] LOCK MOUNT RING
Turn the mount ring to the right until it locks up tight.
Hopper projections must be to the extreme left of
the mounting slots. If the mount ring is hard to turn,
you may add a small amount of petroleum jelly or
liquid soap to the hopper projection. Run water and
check for leaks.
Locking Detall
Hopper Projection in
"Supported" Position
Mounting
Hopper Projection in Ring
"Locked" Position
CHECK FORLEAKS
Check the unit for leaks 24 hours after installation and
firstoperation.
IMPORTANT: Don't put your head or body under
disposer, unit could fall during installation,
Installation Instructions
DIMENSIONS
A: Disposer height
B: Disposer from bottom of sink bowl to
centerline of discharge outlet
C: Distance from centerline of the discharge
outlet to end of discharge tube
D: Disposer width
E: Distance form disposer verlical centerline Lo
centerline of discharge elbow
Cimen-=
Models. A B С D E
No
TR 1500 340 176 70 197 137
TR3400 367 184 70 216 141
SOME TYPICAL INSTALLATIONS
SINGLE BOWL
NOTE: 1. Itis essential for the proper operation
of the disposer thal this dimension be
230-300mm, depending upon the
models listed above, to avoid standing
water in disposer motor housing.
2.Flexible drain pipe may be necessary
for this application.
DOUBLE BOWL
CENTER OUTLET
DOUBLE BOWL
END OUTLET
-9-
Safety Information
Operating Instructions
Installation Instructions
Ta
0
tructi
=
ve)
=
=
—
К
@
a
Troublesshooting Tips
This disposer uses anti-fjam swivel impellers that make a clicking sound as they swing into place. This
indicates normal operation.
Operating Instructions
1. Remove the sink stopper and turn on a medium flow of cold water,
2. Turn on the wall switch.
3. Slowly insert food waste into disposer and position stopper to minimize possible ejection of material while
grinding.
4. After grinding is complete, turn disposer off and run water for at least 15 seconds to flush drain line.
Helpful Hints
DO...
A. Be sure the disposer is empty before using the
dishwasher so it can drain properly.
В. You may want lo leave the stopper in the drain
when not in use to prevent utensils and foreign
objects from falling into the disposer.
C. TO SPEED UP FOOD WASTE DISPOSER... Cut
or break up large bones, melon rinds, grapefruit
skins and corn cobs. Items such as large bones,
fibrous husks like lima bean pods and corn husks
require considerable cutting time. For this reason,
you may prefer to place them in the trash can.
DB, Grind peelings from citrus fruits to freshen up
drain smells.
E. Use a disposer cleaner or deodorizer as
necessary to relieve objectionable odors caused
by grease build-up.
F. Before turning the disposer off, let the water and
the disposer run for al least 15 seconds after
shredding stops. This assures that all waste is
thoroughly flushed through the trap and drain.
Care and Maintenance
DON'T...
A. Don't be alarmed that the disposer slows down while
grinding. The disposer is aclually increasing lorque
(grinding power) and is operating under normal
conditions.
B. Don't pour grease or fat down your disposer or any drain.
It can build up in pipes and cause drain blockages. Put
grease in a jar or can and dispose in the trash.
C. Don't use hot waler when grinding food waste. It is OK to
drain hot water into the disposer between grinding periods.
D. Don't put tin cans, bottles and bottle caps, glass, china,
leather, cloth, crockery, rubber,
string, feathers, or clam or oyster shells into your disposer.
These are waste materials and belong in the trash can.
E. Don't fill disposer with a lot of vegetable peels all at once.
Instead, turn the water and disposer on first and then feed
the peels in gradually.
F. Don't grind extremely fibrous materials like corn husks,
artichokes, etc., To avoid possible drain blockage.
G. Don't turn off disposer until grinding is completed and
only sound of motor and water is heard.
Customer Service
THE MOTOR IS PERMANENTLY LUBRICATED FOR LIFE. DON'TATTEMPT TO LUBRICATE YOUR
DISPOSER, The disposer is self cleaning and scours itself with each use.
& NEVER put lye or chemical cleaners into the disposer, as they cause serious corrosion of metal parts.
@ Yourdisposeris equipped with a removable splash guard for ease of cleaning or replacement. Remove
the splash guard by pulling it out from the top. To replace, insert into the sink flange and push down until
itis properly seated.
E Ifanodor develops, run orange or lemon rinds through the disposer. Adozen ice cubes sprinkled wilh a
little household scouring powder will also work.
-10-
Troubleshooting tips
Before you call for service...
Troubleshooting Tips
Save time and money! Review the chart on this page first and you may not need to call for service.
SAFETY NOTE: Before investigating, you must disconnect the power supply.
A WARNING!
Before resetting, disconnect the power supply-please see SAFETY NOTE above. The overload control prevents
the motor from operating should overloading occur. This feature protects your house wiring and your disposer.
When overloaded, the motor will stop automatically.
Problem Possible Causes
What To Do
Loud noises (other than Silverware, bottle cap or other
those during grinding foreign object has fallen into the
of bones and fruit pits) disposer.
Remove the splash guard and remove the object
with long-handled tongs. Replace the splash
guard.
Disposer does not start Reset button has been tripped.
Reset
Button
With the splash guard removed, check to see if
the turntable will move freely using a broom
handle. If the turntable moves freely, replace the
splash guard and check the resat button to see if
it has been tripped. The reset button is red and
located opposite the discharge elbow, near the
bottom of the disposer. Push the button in until
it clicks and remains depressed. Il the reseal
button has not been tripped, check for a shorted
or broken wire connecting to the disposer.
Check the electrical power switch, fuse box or
circuil breaker. If wiring and electrical
components are intact, the unit may have
internal problems thal require service or
replacement.
Turntable cannot rotate.
Remove
Splash Guard
Turntable
If the turntable does not turn freely, check for an
object lodged between the turntable and the
grind ring. Dislodge the object by moving the
turntable with a broom handle. Then remove the
object. If no foreign object is present, there may
be internal problems.
Disposer leaks If the leak is at the top, it may be
caused by:
|. Improper seating of sink
flange (gasket choice, putty or
tightening).
2. Supportring not tightened
properly.
3. Defective cushion mount.
If the leak is at the discharge
elbow, leak may be caused by
improper tightening of elbow
flange screws.
-11-
safety Information
Installation Instructions
Operating Instructions
E
oc
=
a
|
+
Oo
oO
i
ess
Troubl
Customer Service