Configure start up wizard
Select the screen resolution from the drop-down menu
based on your TV/monitor's resolution.
Resolution
System Resolution: 1024 * 768/60HZ
Check this box if you wish to see this wizard again after you
reboot your system.
Wizard
WM Start wizard when device starts?
We strongly recommend that you change the default
Admin password ‘12345' for better security protection.
Wizard
Admin Password FREER
New Admin Password
New Password
Confirm
Select the applicable time zone, date/time format, and time.
Wizard
Time Zone (GMT-08:00) Pacific Time US & Canada
Date Format MM-DD-YYYY
System Format 09-29-2014
System Time __18:14:37
We recommend checking ‘Enable DHCP’ even if your DVR is not
connected to the internet, this will automatically get the DVR
IP address.
Wizard
NIC Type 10M/100M Self-adaptive
Enable DHCP
IPv4 Address 192.0.0.64
The wizard will show additional network information,
click ‘Next’ to proceed.
Wizard
Server Port 8000
HTTP Port 80
RTSP Port 8554
To initialize the hard drive click the ‘Init’ box otherwise the
DVR will NOT record.
Wizard
Capacity Status Property Type
KZ 465.76GB Normal: RW Local
Free Space
464GB
If you wish to add an IP camera click ‘Search’ otherwise,
click ‘Next’ to proceed. ee
IP Address Amount Model
M1 192.168.1.36 1 CMIP3412
Choose continuous or motion detection recording from the listed
options. Check the ‘Start Recording’ box to initialize recording.
Click ‘Ok’ to finish
fhe wizard,
M Start Recording
O Continuous
Motion Detetction
www.laviewusa.com
What is in the box?
Netowrk Video Recorder
High Definition IP Cameras
Pre-made Cat5e Cables
Remote Control
Mouse
NVR Power Cable
Utility Disc
Quick Start Guide
Warranty Card
Security Stickers
@ Power LED Indicates if the NVR is powered on
O Status LED
Indicates if the Hard Drive is working
(7 GA Port
Connects to TV or computer monitor
© Audio 1/O Connects an extra microphone/speaker
(not included)
© Tx/Rx LED Indicates if the Network is active © LAN Connects to your router
@ Video In Connects cameras via catSe cables @ Rs-485 Connection for additional PTZ camera
(not Included)
@ us: Port Connects to a USB mouse or flash drive ® ACPower Connects the Power Supply
о HDMI Port Connects to HDTV or computer monitor (12) Power Power Switch
Troubleshooting
Problem
Solution
signal/Invalid
format
No display/No | +
Make sure the VGA/HDMI cable is properly connected to both the DVR and TV/monitor
NOTE: A laptop cannot be used as a screen
Make sure your TV/monitor is on the correct video input (e.g. HDMI1, HDMI2, etc.)
* Try switching to another 1080p TV/monitor and adjust the output resolution in the DVR
menu
On the front of the DVR check that the power LED light is on
video
No picture/No | *
Make sure the camera is camera is properly connected to the PoE port on the NVR or
network switch. If the camera does not support PoE or you are connecting it to a
non-PoE switch, you will need additional 12VDC power supply for the camera
Cannot log in
* The default user name is: admin and the default password is: 12345. If you don't
remember your old password, please submit a ticket to us at
www.lavi com/contact/.
Camera
picture is not
clear
Make sure the camera is not placed behind a window, there is no interference or a strong
light source in front of the camera
In DVR Menu>Record>Parameter>Resolution, set the sub stream resolution to CIF for
all channels
Move the camera to a different location and/or direction
NOTE: The live view (sub stream) resolution is NOT the actual image quality recorded (Main
stream); Connection of excessive length (over 300ft)ofcat5e cablewill drop the camera
image quality; Working at extreme weather condition (below -22F or above 140F) will drop
the image quality and damage the camera.
Night vision is
not working
The infrared activates automatically when the environment is dark enough. You can check
that the camera infrared bulbs are working properly as they turn light red in dark
environments
DVR is not
recording
Check that the hard drive status is normal and is initialized under the Main
Menu>HDD>General
Enable the record mode (Normal or Motion Detection) under the Main
Menu>Record>Schedule>Edit for the selected camera
We recommend testing all the cameras and cables prior to installation.
*12VDC Required if POE not available
Wireless Router
#5232 VGA SWRS-485 ke ALARM i ALARM QUT
Esje Go a EEE
"|
OR
VGA
PC Monitor
DVR Adapter
— Mouse
1920x1080
O) Lavie
Innovation That Secures
Premium IP NVR System
QUICK START GUIDE
Remote Viewing
View footage on your mobile devices with our app. You can either
scan the provided QR code below or search LaView Net in the app
store. Then scan the OR code located on the NVR for device P2P info.
ul
# Download on the [m] [m]
| App Store ER
ANDROID APP ON
SCAN ME
>> Google play
LaView NET
Content may vary by model, including the number of channels, cameras, configuration,
and hard drive capacity.
Questions?
Call us at: 626-898-4988 (M-F from 9am to 6pm PST)
Open support ticket at: www.laviewusa.com/contact
Complete user manual can be viewed via included CD disc or
can be downloaded at: www.laviewusa.com/support.
Copyright © LaView Eagle-Eye Technology Inc. 2015
QUICK START GUIDE
Connect your cameras
* Connect the Catbe cable into the camera
* Connect the other end of the Cat5e cable into
the NVR PoE port.
(Repeat for all cameras)
Connect to your monitor/TV
* Connect your NVR and TV/monitor with a HDMI or
VGA cable (Not included)
Note: Your monitor/TV must support the output resolution of the
NVR or you may get a black screen or a possible error message. You
cannot use a laptop as a display.
Connect the mouse and power
Connect the mouse to the USB port
Connect the NVR power cable to the DVR
Connect to your network
Connect the LAN port on the NVR to the LAN port
on your router via an Ethernet cable for remote
viewing on your mobile phone, tablets, PC and Mac
You can also add existing IP cameras to your NVR from
your network.
Note: The NVR will still work as a standalone video recorder if you do
not have internet connection and skip this step.
(OPTIONAL)
Configure the start up wizard
The connection is now completed. Turn on the
power switch and follow the start-up wizard on
your screen to configure the NVR. (Next Page)
">
