Escort Beltronics GT-360 Owner's Manual
Add to my manuals10 Pages
Beltronics GT-360, your trustworthy guardian on the road, offers unrivaled 360° protection. Its HD Performance detects real threats faster, pinpoints their location with threat direction arrows, and intelligently eliminates false alerts using GPS technology and the updatable IVT Filter™. Stay informed and drive confidently with the GT-360.
advertisement
Programming
Press and hold the BRT and SEN buttons to access Programming. To exit Programming, simply wait a few seconds without pressing a button. The unit will display Completed to confirm your selections.
Press BRT to go from one category to the next
Press VOLUME + or – to change your setting within a category
User Mode Advanced*
Novice
Access and customize all Settings and Preferences
Access and customize units and display color, (all other
Settings are set to factory defaults)
NOTE: Switch back to Advance mode to view all Preferences
Scan Bar*
Full Word
Scanning Bar with Full Word
Full Word: AutoScan, Auto NoX, or Highway
Display Color Copper*/Blue/Green/Red Set color to match your vehicle’s dash display
Speed Display On*
Off
Displays current speed
Displays battery voltage
Offers double beep alert tones below specified speed Cruise Alert Off / 20-160 mph
20 mph*
Over Speed Off / 20-160 mph
70 mph*
Reminds you when you exceed a specified speed
Meter Mode Standard*
Tech
Basic
Standard*
Mild
AutoMute
Single band with front and rear signal strength bar graphs
Single band with numeric frequency and front and rear signal strength bar graphs
Simple messages replace bands:
Caution (if traveling below cruise alert limit)
Slow Down (if traveling above cruise alert limit)
Standard Beltronics alert tones
Mild doorbell chime alert tones
Automatically reduces audio to preferred volume during alert
Automatically stores and locks out false alarms
Language
GPS Filter On* / Off
Units for distance and speed
Language for voice and text
Voice announcements
Enables GPS-powered features
7
Programming
AutoPower type (constant power or switched)
1 Hour
2 Hours
4 Hours*
8 Hours
Powers off automatically after 1 hour
Powers off automatically after 2 hours
Powers off automatically after 4 hours
NOTE:
AutoPower only works with constant power ignition
NOTE: If AutoPower is on, to save screen life the display screen goes blank after 30 minutes without moving.
Band Enables Default* Default Settings
Modified Band Enables have been modified from their default settings
Press SEN to go from one
band category to the next
Press VOLUME + or – to change your setting within a category
X Band On* / Off
K Band On* / Off Freq: 24.050-24.250 GHz
NOTE: When K Band is off, you can select separate segments of the band to turn on or off.
On* / Off Freq: 24.050 - 24.110 GHz
KN2
Ka Band
On* / Off
On* / Off
KaN1 On / Off* Freq: 33.400 - 33.700 GHz KaN6 On / Off* Freq: 34.800 - 35.160 GHz
On / Off*
Freq: 24.110 - 24.175 GHz
KN3
KN4
Freq: 33.400-36.000 GHz
NOTE: When Ka Band is off, you can select separate segments of the band to turn on or off.
KaN4 KaN9 On / Off* Freq: 35.600 - 35.840 GHz
KaN5 On / Off* Freq: 35.840 - 36.000 GHz
Ka Band On* / Off
Ka-POP
On* / Off
TSR
Freq: 35.160 - 35.400 GHz
KaN3 On* / Off Freq: 35.400 - 35.600 GHz
Marker Enable On* / Off Default Settings
Modified Marker Enables have been modified from their default settings
8
Programming
Press SEN to go from one
marker category to the next
Press VOLUME + or – to change your setting within a category
On* / Off
On* / Off
Red & Speed On* / Off
Redlight
Speed Cam On* / Off
Air Patrol On / Off*
Speed Trap On* / Off
Air Patrol On / Off*
Other location
Red light camera
Red light & speed camera
Speed camera
Known aircraft patrolled areas
NOTE: User cannot mark an air patrol location
Speed trap
Known aircraft patroled areas
NOTE: User cannot mark an Air Patrol location
Clear Locations Marked Clear all user Marked locations. Press SEN button to confirm
Lockouts Clear all lockouts. Press SEN button to confirm
Clear DEFENDER database, all markers, and all lockouts.
Press SEN button to confirm
*Default Setting
Defender
Format
Clear all DEFENDER data. Press SEN button to confirm
9
Contact Us
Notes for Programming
For descriptions of features and functions available when connected to ESCORT Live, visit
Beltronics.com and download the GT-360 Owner’s
Manual.
To view serial number and software revision press
MRK and MUTE while powering on detector.
To restore GT-360 to its original factory Settings, press and hold MRK and BRT while turning the power on. A Restored message will display, acknowledging the reset.
Software Updates
GT-360’s red light and speed camera database is easily updated using our exclusive detector software tools found on our web site. Firmware, or the operating software for the detector, can also be updated using these tools.
In order to have access to these updates, you must register your GT-360 at www.Beltronics.
com. Once registered, you will receive email notifications that updates are now available for your database or firmware. To handle your software and DEFENDER updates you need to connect your GT-360 to a computer first. You can connect GT-360 to a computer via USB/USB Mini
B cable.
10
866.468.0322 • Beltronics.com
Beltronics USA, Inc.
5442 West Chester Road, West Chester OH 45069
Beltronics One Year Limited Warranty
What this warranty covers: Beltronics USA, Inc. (“Beltronics”) warrants your Product against all defects in materials and workmanship.
For how long: One (1) year from the date of original purchase from an authorized Beltronics dealer.
What we will do: If a breach of warranty occurs, Beltronics, at its discretion, will either repair or replace your Product free of charge.
What we will not do: Beltronics will not pay shipping charges that you incur for sending your Product to us.
What you must do to maintain this warranty: Show original proof of purchase or receipt from an authorized Beltronics dealer.
Warranty exclusions: This warranty does not apply to your product under any of the following conditions: 1. The serial number has been removed or modified. 2. Your product has been subjected to misuse or damage (including water damage, physical abuse, and/or improper installation). 3. Your product has been modified in any way. 4. Your receipt or proof-of-purchase is from a non-authorized dealer or internet auction site, including E-bay, U-bid, or other non-authorized resellers.
5. You are not the original purchaser of the Product from an authorized dealer or did not receive it as a gift from the original purchaser of the
Product from an authorized dealer.
To obtain service: 1. Contact Beltronics (1-800-341-2288) to obtain a Return Authorization Number. 2. Properly pack your Product and include: your name, complete return address, written description of the problem with your Product, daytime telephone number, and a copy of the original proof of purchase or receipt. 3. Label the outside of the package clearly with your Return Authorization Number. Ship the
Product pre-paid (insured, for your protection) to: Beltronics USA, Inc.,
5442 West Chester Rd., West Chester, OH 45069.
LIMITATION OF WARRANTY: The obligations set forth above are
Beltronics’ sole obligations and your exclusive remedy. Beltronics makes no other express warranty. Any implied warranty of merchantability or fitness for a particular purpose that may be applicable to the Product is limited in duration to the duration of this warranty. Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. BELTRONICS SHALL NOT BE LIABLE
FOR CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES INCLUDING,
WITHOUT LIMITATION, DAMAGES ARISING OUT OF THE USE, MISUSE OR
MOUNTING OF THE PRODUCT. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Beltronics is not responsible for products lost in shipment between the owner and our service center.
Other legal rights: This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
©2018 Beltronics USA, Inc. Beltronics®, GT-360™, Escort Live!™, Defender®,
TrueLock™, SmartShield®, SpecDisplay™, AutoSensitivity™ and EZ Mag Mount™ are trademarks of Beltronics USA, Inc. Manufactured in the Philippines.
Features, specifications and prices subject to change without notice.
FCC NOTE: Modifications not expressly approved by the manufacturer could void the user’s FCC granted authority to operate the equipment.
FCC ID:QL4M6. CONTAINS FCC ID:QKLBT2
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received including interference that may cause undesired operation.
Live life in the passing lane.
Live life in the passing lane.
Arrows indicate direction of the threat.
GT-360
360° Protection with Threat Direction
Dual Antenna Front
& Rear Protection
GPS Intelligence Rejects
False Alerts
ESCORT Live
Crowd Sourced Alerts
Quick Reference
Lightning Fast
Response
Congratulations
Take the freedom of the road back with the
Beltronics GT-360, equipped with 360° high definition protection, threat direction arrows, and intelligent GPS technology to eliminate false alerts.
Go to Beltronics.com for full featured Owner’s
Manual.
GT-360 features a new multi-color
OLED display.
Brilliant graphics illuminate intuitive icons that identify the type of threat at a glance.
GT-360 Features
• GT-360’s HD Performance accurately identifies real threats sooner than other detectors, and with threat direction arrows, provides you with location information about these threats.
• Updatable IVT Filter™ automatically reduces false alerts from moving In-Vehicle Technology sources such as collision avoidance systems and adaptive cruise control.
• GPS location-based intelligence automatically locks out false alerts and allows you to mark locations for future reference.
• Access to the DEFENDER Database, which warns you of verified speed traps, speed cameras, and red light cameras.
• Built in Bluetooth® technology gives you access to ESCORT’s award winning app, ESCORT Live.
The exclusive real-time ticket-protection network which warns you of upcoming alerts received and reported by other users in the area, and gives you access to local speed limit data for over-speed alerts.
H I G H D E F I N I T I O N 3 6 0 ° P R O T E C T I O N
2
Registration and ESCORT Live
Before downloading ESCORT Live, you must first register your device. Be sure to have your device nearby, as you will need its serial number.
1 Visit www.Beltronics.com and click Product
Registration.
2 Click the “Registration for all devices” link.
3 Follow the onscreen instructions to register
your device.
Be sure to write down the username and password you create, as you will need this information to access and download ESCORT Live. (You will also receive an e-mail with this information, once you have registered your device.)
For iPhone:
1 Ensure GT-360 power is ON
2 Open the App Store on your iPhone
and search for ESCORT Live Radar.
3 Follow the onscreen instructions to download
ESCORT Live Radar and then open the app.
4 When prompted, enter the username and
password you created when registering your
product at Beltronics.com.
5 Press the Settings button then select
Devices.
6 You should see GT-360
listed with Not Connected
underneath.
Press the GT-360 device
entry and when prompted
select Pair.
7 The Bluetooth icon on the GT-360 display
will appear to confirm that it is paired to
your iPhone.
3
For Android based smartphones:
1 Ensure GT-360 power is ON.
2 On your smartphone go to Bluetooth® Settings
and make sure that Bluetooth® is ON.
3 Press Scan for devices and wait for the device
list to populate, GT-360 should appear
under Available devices.
4 Press the GT-360 device entry.
5 The Bluetooth icon on the GT-360 display
will appear to confirm that it is paired to your
smartphone.
6 Open Google Play on your smartphone
and search for Escort Live Radar.
7 Follow the onscreen instructions to download
Escort Live Radar and then open the app.
8 When prompted, enter the username and
password you created when registering your
product at Beltronics.com.
7 Open the app, walk through the tutorial, and
you’re ready to hit the road!
Your new detector comes with the revolutionary
EZ Mag Mount™. Simply tilt the display end of the detector up and slide it onto the mounting bracket. The magnetic mount holds the detector in place. To remove the detector from the mount, simply lift the display end of the detector and the detector releases from the mount.
Mounting Tips:
• Center of windshield between driver and
passenger.
• Ensure clear view of road ahead and sky
above.
• Avoid windshield wipers and heavily tinted
areas.
To mount the detector in your vehicle:
1 Remove paper backing from EZ Mag Mount™ `
StickyCup.
2 Ensure the locking clamp is open.
3 Firmly press EZ Mag Mount™ StickyCup onto windshield and close the locking clamp to secure.
4 To adjust view, loosen thumb wheel and adjust angle of mounting bracket. Tighten thumb wheel to secure.
5 Tilt the display end of the detector slightly upward and engage with the flanged edge of the mounting bracket. The EZ Mag Mount™ magnet holds the detector in place.
6 To remove the detector, simply lift the display end of the detector upward. The detector will release from the mount.
7 To remove mount from windshield, release locking clamp and pull tab on top of StickyCup.
EZ Mag Mount™ Care Instructions:
Should the EZ Mag Mount™ StickyCup accumulate debris and lose its stickiness, simply rinse under warm water, gently wipe off debris and allow to air dry.
EZ Mag Mount™
Release Tab
StickyCup
Locking Clamp (closed)
GT-360
Thumb Wheel For
Angle Adjustment
Mounting Bracket
4
Using GT-360
1 Plug small end of SmartCord USB into modular jack on GT-360 and large end of SmartCord USB into your vehicle’s lighter/accessory socket
2 GT-360 should power on automatically. If not,
press the device’s power button.
Power requirement
11.0-16.0 Volts DC negative ground
400mA standby, 700 mA maximum
NOTE: You can easily access and customize all of your Settings and Preferences by pressing and holding the BRT and SEN buttons. See Settings and
Preferences for details.
Using SmartCord USB
• Mute Button:
- Press to mute the audio for a specific alert.
- Press three times to lock out a false alert.
- Press twice while receiving a locked-out alert
to unlock.
- When connected to ESCORT Live press and
hold mute button on unit or cord to manually
report to other users a verified X or K-band
alert, or a police officer observing traffic.
• Alert Light: Blinks red when receiving a radar or
laser alert.
• Power Light: Lights green when device is
powered on.
• USB Charging Port: Charge smartphones,
tablets and other USB-charged Devices.
Mounting Bracket
Modular Jack
Connects to SmartCord for powering your device
Earphone Jack
Connects to optional 3.5 mm stereo earphone.
5
Modular Connector
Plugs into detector jack
SmartCord USB Adapter
Connects to lighter/accessory socket
Mount Area
The EZ Mag Mount™ attaches to device here
BRT
Press to adjust display brightness (Min, Med,
Max, Auto, Dark)
MRK
To mark a location for future alerts, press MRK twice, then VOL + or – to select the type of marker, then MRK again to confirm. Press twice while receiving marker alert to unmark
Volume
Press and hold + or – to adjust volume
Power
Press to turn GT-360 on or off
MUTE
Press to mute an alert; press three times to lock out a false alert; press twice while receiving a locked-out alert to unlock
SEN
Press to adjust detector sensitivity
(Auto, AutoNoX,
AutoLoK, and
Highway)
Display
Alert area
Display
Showing current speed
Display (OSP)
OverSpeed alert setting that can be adjusted in Preferences. Bluetooth icon will appear on display screen blue when paired to phone and Speed limit data will show here when ESCORT Live App is open.
6
Continued ➜
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project