Rust-Oleum RockSolid 318711, 286891, 286890, 308638, 286879, 286892, 308637, 318699 User manual

Rust-Oleum RockSolid 318711, 286891, 286890, 308638, 286879, 286892, 308637, 318699 User manual
TECHNICAL DATA
RSD-01
ROCKSOLID® POLYCURAMINE
GARAGE FLOOR COATING KIT
DESCRIPTION AND USES
PRODUCT APPLICATION (cont.)
®
SURFACE PREPARATION (cont.)
RockSolid Garage Floor Coating Kit is designed to provide
excellent hardness, adhesion and durability on properly
prepared concrete floors. It has excellent resistance to salt,
oil, gasoline and other harsh chemicals. This garage floor
coating contains zero VOC making it environmentally safe
and is packaged in pouches, which reduces waste.
Use the supplied RockSolid concrete etch per the
instructions to provide the proper surface condition to
ensure proper adhesion. Rinse the floor thoroughly and
allow it to dry completely.
Moisture Testing - New concrete should be allowed to cure
for 30 days before application of any coating. If there is any
doubt about the dryness of the concrete, conduct a test by
simply taping a piece of 4 mil plastic sheet 18x18” on the
bare concrete for 24 hours. Be sure to tape all four sides.
After 24 hours, check the concrete for signs of moisture.
The concrete substrate will be darker if damp. If moisture is
found, allow additional drying time (10-14 days) and repeat
the test.
PRODUCT FEATURES









Low odor and can be applied indoors
Formulated without the addition of VOC containing
solvent
One coat system
45 minute pot life
Patented Burst Pouch Technology
96% solids formulation
Has excellent self-leveling properties
7 day recoat window without sanding
Excellent durability in a single coat
Testing for Sealer - Check for curing compounds or other
types of sealers by pouring a small amount of water onto the
concrete. If water soaks in, the surface is suitable for
coating. If water beads up on the concrete, the surface is
not porous and a test application is warranted to ensure
proper adhesion will develop. Sanding or mechanical
abrading may be required if proper adhesion does not
develop.
KIT CONTENTS





Polycuramine Burst Pouch (Two part Burst Pouch
Technology U.S. Patent Number 8,381,903 B2)
Foam Roller
Decorative Chips
Concrete Etch
Instructions
Previously Coated Floors - Previously coated floors need
to be in good condition with proper adhesion to the concrete
substrate. Check the adhesion of the previous coating by
cutting a small X in the coating using a sharp razor knife.
Firmly apply a piece of 5” duct tape over the center of the X
cut, and then pull off with a fast snap. If more than 10% of
the taped area is removed, the original coating is not
bonded well and needs to be removed chemically or
mechanically with a grinder.
PRODUCTS
SKU
286879
286891
286890
286892
308637
308638
318699
318711
DESCRIPTION
Gray 2.5 Car Kit
Gray 1 Car Kit
Mocha 2.5 Car Kit
Mocha 1 Car Kit
Dark Gray 2.5 Car Kit
Dark Gray 1 Car Kit
Black 2.5 Car Kit
Black 1 Car Kit
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800424-LEAD or log on to www.epa.gov/lead.
PRODUCT APPLICATION
SURFACE PREPARATION
Proper surface preparation is critical to achieve best results.
Scrub heavily soiled areas with RockSolid Heavy Duty
Degreaser or Rust-Oleum Cleaner & Degreaser (sold
separately). Scrub thoroughly, then rinse. Repeat as
needed.
MIXING
MIX ONLY ONE POUCH AT A TIME. Both components and
the environment should be pre-conditioned to a minimum of
40ºF (4ºC) prior to use. Be sure the air and surface
temperatures are at least 5º above the dew point.
1
Form: GDH-604
Rev.: 013119
TECHNICAL DATA
RSD-01
ROCKSOLID® POLYCURAMINE
GARAGE FLOOR COATING KIT
PRODUCT APPLICATION (cont.)
PRODUCT APPLICATION (cont.)
MIXING (cont.)
CLEAN-UP
Combine the two components by placing the pouch on the
ground and rolling it from the part A side towards the part B
side like a tube of toothpaste. This will create pressure in the
part A side and force the middle seal to burst, allowing the
two components to mix together. Thoroughly mix the
materials by shaking the pouch back and forth and
squeezing the edges and corners toward the center of the
pouch. Mix for 2-3 minutes.
Clean tools and equipment with mineral spirits. Allow
unused product to harden in container and dispose
according to local regulations.
LIMITATIONS
This product must be installed at the specified spread rates
to perform as described. Do not apply in direct sunlight. Do
not apply product when the substrate and ambient
temperatures are steadily below 40°F (4°C).
APPLICATION
SHELF LIFE and STORAGE
Apply only when air, material and floor temperatures are
between 40-90°F (4-32°C). Optimal installation temperature
is 55-90°F (13-32°C). Extreme cold application temperatures
may slow the cure time. Do not apply in direct sunlight.
Do not coat the floor if it is raining or if extremely damp
conditions exist. The concrete surface must be completely
dry at the time of the application to achieve proper adhesion.
Sixty (60) months in factory delivered unopened pouches.
Keep away from extreme heat, cold and moisture. Maintain
at a proper storage temperature of 45-90°F. Keep out of
direct sunlight and away from fire hazards.
PERFORMANCE CHARACTERISTICS
Once the material in thoroughly mixed, use a scissors to cut
a corner off the pouch. Pour the contents of the pouch
directly onto the floor in a 2-3” wide ribbon about 4’ long.
Trim the edges from the poured ribbon of material using a
good quality synthetic brush. Use the supplied RockSolid
⅜” Microfiber Roller Cover on a 9” roller frame to apply the
coating evenly to the floor in 4’ x 4’ sections in an “M” and
“W” pattern. Continue working in 4’ x 4’ sections, pouring a
new ribbon 2’ away from the previous section. Use the roller
to pull the material back first; then push forward to fill in the
void between sections. Overlap into the previously coated
areas while taking care to avoid creating thick spots.
FLEXIBLITY (1/8” MANDREL)
Once a strip across the entire back wall has been coated,
toss the decorative paint chips onto the wet coating. Leave a
6”-12” section of wet film without decorative chips. This
section will be rolled into when coating the next 4’ x 4’ area.
Skip this step if paint chips are not desired. The coating
performance will not be affected.
ABRASION RESISTANCE
METHOD: ASTM D1737
RESULT: Pass
HARDNESS SHORE D
METHOD: ASTM D2240
RESULT: 90
GLOSS @ 60°
METHOD: ASTM D523
RESULT: >95
METHOD: ASTM 4060, CS 17, 1,000 gram load
RESULT: Loss/1000 cycles = 40 mg
Do not coat or roll over control joints. Use a flexible control
joint fill material if desired. Repeat the above steps for each
additional pouch.
COVERAGE RATE
Each Polycuramine pouch covers up to 200-250 square feet.
Coverage may vary based on condition and porosity of the
concrete.
DRY TIME
Temperature and humidity may affect drying time. Do not
walk on the coating while it is still tacky. Surface should be
ready for foot traffic in 8-10 hours and vehicle traffic in 24-36
hours depending upon temperature and humidity.
2
Form: GDH-604
Rev.: 013119
TECHNICAL DATA
RSD-01
ROCKSOLID® POLYCURAMINE
GARAGE FLOOR COATING KIT
PHYSICAL PROPERTIES
Resin Type
Proprietary Blend of Epoxy, Urethane and Polyurea
Pigment
Varies with color
Solvent
Benzyl Alcohol, 1-Choro-4-(Trifluoromethyl) Benzene, Nonylphenol, Neopentyl
Glycol Diglycidyl Ether
Per Gallon
Weight
9.1-9.3 lbs.
Per Liter
1.09-1.11 kg
Solids By Volume
96%
Volatile Organic Compounds
<1 g/l
200-250 sq.ft./kit (4.9-6.2 m2/l)
(coverage rate can vary depending on texture and porosity of concrete)
Practical Coverage
Pot Life
Dry Times @ 70-80º F
(21-27°C) and 50%
Relative Humidity†
45 minutes to 1 hour (depending on temperature and humidity)
Tack Free
8-10 hours
Dry Hard
12-16 hours
Vehicle Traffic
Shelf Life
24-36 hours depending on temperature
60 months unopened factory delivered pouches
Safety Information
For additional information, see SDS
Calculated values are shown and may vary from the actual manufactured material.
†
Dry times will be increase if temperatures are less than 55ºF (13ºC).
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
Phone: 877∙385∙8155
www.rustoleum.com
Form: GDH-604
Rev.: 013119
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement